Security System

User's Manual

4110DL/4110XM

N5100V5 Rev B 4/99

TABLE OF CONTENTS

SYSTEM OVERVIEW.....4 Keypads.....4 Zones.....4 Alarms.....5 Fire Protection.....5 Burglary Protection....5 Memory of Alarm.....5 Pager Notification.....5 ABOUT THE KEYPADS....6 Keypad Types.....6 Keypad Styles....6 SUMMARY OF SYSTEM STATUS DISPLAYS....7 SUMMARY OF KEYPAD FUNCTIONS....8 SECURITY CODES..... 10 Duress Code..... 10 Quick Arming..... 10 Assigning/Changing/Deleting User Codes (Using the 8 CODE Key).. 11 ENTRY/EXIT DELAYS.... 12 CHECKING FOR OPEN ZONES (Using the READY Key).... 13 BYPASSING PROTECTION ZONES.... 14 Using The 6 BYPASS Key.... 14 Quick Bypass.... 15 ARMING PERIMETER ONLY, WITH ENTRY DELAY ON (Using The 3 STAY Key)... 16 ARMING PERIMETER ONLY, WITH ENTRY DELAY OFF (Using The 7 INSTANT Key ).. 17 ARMING ALL PROTECTION, WITH ENTRY DELAY ON (Using The 2 AWAY Key).. 18 ARMING ALL PROTECTION, WITH ENTRY DELAY OFF (Using The 4 MAXIMUM Key).. 19 2

(continued)

DISARMING THE SYSTEM AND SILENCING ALARMS (Using the 1 OFF Key)... 20 USING THE KEYSWITCH..... 21 CHIME MODE (Using the 9 CHIME Key).... 22 PANIC KEYS.... 22 TESTING THE SYSTEM (Using the 5 TEST Key)... 24 TROUBLE CONDITIONS.... 26 "Check" and "Battery" Displays.... 26 Power Failure..... 27 Other Displays..... 28 FIRE ALARM SYSTEM, IF INSTALLED.... 29 In Case of Fire Alarm..... 29 Silencing Fire Alarms..... 30 NATIONAL FIRE PROTECTION ASSOCIATION RECOMMENDATIONS ON SMOKE DETECTORS.. 31 EMERGENCY EVACUATION.... 32 QUICK GUIDE TO ALARM SYSTEM FUNCTIONS.... 33 SUMMARY OF AUDIBLE/VISUAL NOTIFICATION... 34 PROTECTION ZONES LIST..... 35 OWNER'S INSURANCE PREMIUM CREDIT REQUEST... 37 CANADIAN DEPARTMENT OF COMMUNICATIONS (DOC) STATEMENT.. 39 FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTS... 40 IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS... 41 THE LIMITATIONS OF THIS ALARM SYSTEM.... 42 SERVICING INFORMATION..... 43 WARRANTY....Back Cover This manual is a step-by-step guide that will aquaint you with the system's features and benefits. It defines the components and their functions, describes their operation, and instructs you with normal and emergency procedures. Keep this manual in a convenient place so that you can refer to it as necessary. 3

SYSTEM OVERVIEW

General Congratulations on your ownership of an Ademco Security System. You've made a wise decision in choosing it, for it represents the latest in security protection technology today, including microcomputer technology to monitor all system status. Ademco is the world's largest manufacturer of security systems and millions of premises are protected by Ademco systems. Basically, this system offers you three forms of protection: burglary, fire and emergency. Your system may consist of at least one keypad which provides full control of system operation, various sensors such as motion detectors and door and window sensing devices, plus a selected number of strategically placed smoke or combustion detectors designed to provide early warning in case of fire. Your system may also have been programmed to automatically transmit alarm or status messages over the phone lines to a central alarm monitoring station. All system functions are controlled by your keypad(s). The keypads feature a telephone style (digital) keypad and a Liquid Crystal Display (LCD) which shows the nature and location of all occurrences. Their built-in sounder will sound during alarm and trouble conditions. For additional information, see the following section: ABOUT THE KEYPADS. Your system's sensing devices have been assigned to various zones. For example, the sensing device on your Entry/Exit door may have been assigned to zone 01, sensing devices on windows in the master bedroom to zone 02, and so on. These zone numbers will appear on the display when an alarm or trouble condition occurs.

Keypads

Alarms
When an alarm occurs, both the keypad and external sounders will sound, and a message at the keypad will identify the zone(s) causing the alarm. In addition, if your system is connected to a central monitoring station, an alarm message will be sent. To stop the alarm sounding, you simply disarm the system. The fire protection portion of your security system (if used) is always on and will sound an alarm if a fire condition is detected. Refer to the FIRE ALARM SYSTEM section for important information concerning fire protection, smoke detectors and planning emergency exit routes from your premises. The burglary protection portion of your system must be turned on or "armed" before it will sense burglary alarm conditions and sound an alarm. Your system can be armed in one of four modes: STAY, AWAY, INSTANT and MAXIMUM. Refer to the ARMING THE SYSTEM sections for instructions in using these modes of operation. Your system also provides a CHIME mode for alerting you to the opening and closing of doors and windows while the system is disarmed. When an alarm or trouble condition occurs, the keypad displays the number(s) of the zone(s) that caused the problem, and displays the type of alarm or trouble (ex. FIRE, ALARM, CHECK). The display remains until it is cleared by entering the OFF sequence (security code + OFF key) twice. If you have chosen to be notified of alarms or other system conditions b y pager, the following codes will be sent to your pager by the control: 1811=Trouble 1911=Alarm 1001=Open 1002=Close

ALARM STAY CHIME FIRE CHECK INSTANT

BYPASS NOT READY

STYLE B KEYPAD
IMPORTANT!: When entering codes and commands, sequential key depressions must be made within 2 seconds of one another. If 2 seconds elapses without a key depression, the entry is aborted and must be repeated from its beginning.

SECURITY CODES

General At the time of installation, your installer programmed a personal four-digit Master code, known only to you and yours. This code is used to perform most system functions, including arming and disarming of the system. As an additional safety feature, temporary user codes can be assigned (see next page) for use by those not having a need to know the Master code. Note that the Master code remains in effect even when other user codes are assigned. This feature is intended for use when you are forced to disarm or arm the system under threat. When used, the system will act normally, but can silently notify the central station of your situation, if that service has been provided. The Duress code is defined as user number 8. Important: The Duress code is useful only when connected to a central station. If your system supports "Quick Arming", the "#" key can be pressed in place of the security code when arming the system. The security code is always required, however, when disarming the system. accept

Duress Code

Ask your installer if "Duress" is active for your system, and if so, check here:

Quick Arming

Ask your installer if "Quick Arming" is active for your system, and if so, check here:
To Assign, Change, or Delete User Codes
1. Enter your Master code and press the CODE key. 2. Enter single-digit user number ('2', '3', '4', '5', '6' or '7') for which a code is to be assigned, changed, or deleted. 3. If assigning or changing a user's code, enter the desired 4-digit code for use by that user number. The keypad will beep once. If deleting a user's code, perform steps 1 & 2 and stop. In a few moments the keypad will beep once, indicating that the existing code has been deleted. To assign your Duress code, do the following: Enter your [Master code] + [8] + [8] + [desired 4-digit code]. The keypad will beep once. The Master code can be changed by the main user of the system. To change it, do the following: Enter your [Master code] + [8] + [1] + [new Master code] + [new Master code] again. The keypad will beep once. Important:Temporary users should not be shown how to use any system function they do not need to know (e.g., bypassing protection zones).

4-DIGIT USER CODES It is recommended that obvious codes such as or not be assigned.

ENTRY/EXIT DELAYS

General Information Your system has preset time delays, known as exit delay and entry delay. When you arm your system, exit delay gives you time to leave through the entry/exit door without setting off an alarm. Entry delay gives you time to disarm the system when you reenter through the entry/exit door. The system must be disarmed, however, before the entry delay period ends, or an alarm will occur. The keypad will beep slowly during the entry delay period, reminding you to disarm the system. You can also arm the system with no entry delay at all by using either INSTANT or MAXIMUM arming modes. These modes can provide greater security while you are sleeping or while you are away for extended periods of time. See your installer for your delay times and record them here: Exit Delay: seconds Entry Delay: seconds

CHECKING FOR OPEN ZONES

Using the Before your system can be armed, all protected doors, windows and other READY Key protection zones must be closed or bypassed (see BYPASSING PROTECTION ZONES section), otherwise the keypad will display a "Not Ready" message, and if your keypad has a READY indicator light, it will not be lit. The READY key can be used to display all faulted zones, making it easier for you to secure any open zone. To display faulted zones, simply press and release the READY key (do not enter code first). Secure or bypass the zones displayed before arming the system. A "Ready" message will be displayed when all protection zones have been either closed or bypassed and the keypad's READY indicator light (if present) will be lit.
TYPICAL DISPLAYS WHEN NOT READY TO ARM TYPICAL DISPLAYS INDICATING FAULTED PROTECTION ZONE (AFTER PRESSING READY KEY) TYPICAL DISPLAYS INDICATING "READY TO ARM"

ALARM FIRE CHECK

AWAY BYPASS STAY
SUPV NO AC PHONE TEST NOT READY CHIME BAT TAMPER

03 ALARM

BYPASSING PROTECTION ZONES

Using the 6 BYPASS Key

LIMITATION The system will not allow fire zones to be bypassed. All bypasses are removed when an OFF sequence (security code plus OFF) is performed.

USER CODE + INSTANT KEY ARMS THE PERIMETER (INCLUDING THE ENTRY/EXIT DOOR), WITH NO ENTRY DELAY.
TYPICAL DISPLAYS "ARMED INSTANT"

ARMING ALL PROTECTION

WITH ENTRY DELAY ON Using the 2 AWAY Key
Use this key when no one will be staying inside. 1. Enter your security code and press the AWAY key. 2. The keypad will beep twice and will display the armed message. The red ARMED indicator will light. 3. You may leave through an entry/exit door during the exit delay period without causing an alarm. After exit delay, the system arms and will sound an alarm if a protected window or non-entry/exit door is then opened, or if any movement is detected inside your premises. You may reenter through an entry/exit door, but must disarm the system within the entry delay period to avoid an alarm.
USER CODE + AWAY KEY ARMS ALL BURGLARY PROTECTION (INTERIOR AND PERIMETER), BUT ALLOWS USE OF THE ENTRY/EXIT DOOR.
TYPICAL DISPLAYS "ARMED AWAY"
WITH ENTRY DELAY OFF Using the 4 MAXIMUM Key
Use this key when the premises will be vacant for extended periods of time such as vacations, etc., or when no one will be moving through protected interior areas. 1. Enter your security code and press the MAXIMUM key. 2. The keypad will beep twice and will display the armed message. The red ARMED indicator will light. 3. You may leave through an entry/exit door during the exit delay period without causing an alarm. After exit delay, the system arms and will sound an alarm immediately if any protected door or window is opened, or if any movement is detected inside your premises. An alarm will sound immediately, when someone reenters.
USER CODE + MAXIMUM KEY ARMS ALL BURGLARY PROTECTION (INTERIOR AND PERIMETER), (INCLUDING THE ENTRY/EXIT DOOR WITH NO ENTRY DELAY).
TYPICAL DISPLAYS "ARMED MAXIMUM"
DISARMING THE SYSTEM AND SILENCING ALARMS

Using the 1 OFF Key

IMPORTANT: If you return and the main burglary sounder is on: DO NOT ENTER, but CONTACT THE POLICE from a nearby safe location. If you return after an alarm has occurred and the main sounder has shut itself off: the keypad will beep rapidly upon your entering, indicating that an alarm has occurred during your absence (the Memory of Alarm feature). LEAVE IMMEDIATELY, and CONTACT THE POLICE from a nearby safe location. WHEN SAFE TO DO SO, re-enter and follow the procedure for silencing an alarm.

PANIC KEYS

Using Panic Keys
(for manually activating silent and/or audible alarms)
TO INITIATE A PANIC FUNCTION AT ANY TIME OF DAY OR NIGHT: Press an active lettered key for at least two seconds. or Press both keys of an active pair at the same time. * If connected
Your system may have been programmed to use special keys or combinations of keys to manually activate emergency (panic) functions. The functions that might be programmed are: Silent Emergency, Audible Emergency, Personal Emergency, and Fire. A silent emergency will send a silent alarm signal to the central station*, but there will be no audible alarms or visual displays. An audible emergency will send a signal to the central station* and sound a loud, steady alarm at your keypad(s) and at any external sounders that may be connected (ALARM plus a zone number would also be displayed). A personal emergency alarm will send an emergency message to the central station* and will sound at keypad(s), but not at external bells or sirens. A fire alarm will send a fire alarm message to the central station* and will uniquely sound at keypad(s) and external bells and sirens (FIRE plus a zone number would also be displayed).

A B C D

OFF AWAY STAY

1 & * 3 &#

LETTERED EMERGENCY KEYS ("D" IS NOT USED)

INSTANT CODE

> EMERGENCY

PAIRED

TYPICAL KEYPAD

* & #

CHECK IF ACTIVE

PANIC KEY(S) [A] [B]

P R O G R A M M E D F U N C T I O N SILENT EMERGENCY (Fixed-Function) ____SILENT, ____AUDIBLE, ____PERSONAL, ____FIRE AUDIBLE EMERGENCY (Fixed-Function)

ZONE NUMBER 96

SEE YOUR INSTALLER AND NOTE HERE THE KEY(S) & FUNCTION(S) PROGRAMMED FOR YOUR SYSTEM
[C] OR [1] & [] [] & [#] [3] & [#]
SILENT EMERGENCY (Fixed-Function) ____SILENT, ____AUDIBLE, ____PERSONAL, ____FIRE AUDIBLE EMERGENCY (Fixed-Function)
KEYS [A], [B], AND [C] ARE NOT PRESENT ON ALL KEYPADS. KEY [D], IF PRESENT ON YOUR KEYPAD, IS NOT ACTIVE HERE.

TESTING THE SYSTEM

TO BE CONDUCTED WEEKLY

Using the 5 TEST Key

NO ALARM REPORTS WILL BE SENT TO THE CENTRAL MONITORING STATION while the system is in Test mode.
The TEST key puts your system into Test mode, which allows each protection point to be checked for proper operation. 1. Disarm the system and close all protected windows, doors, etc. The keypad's READY message should be displayed and the READY indicator (if present) should be lit. 2. Enter your security code and press the TEST key. 3. The keypad will sound a single beep every 40 seconds as a reminder that the system is in the test mode. Each time a protection zone is faulted, the external siren or bell should sound for one second and then turn off, while the keypad sounds 3 beeps. If this does not happen, call for service immediately. 4. Open and close each protected door and window in turn and listen for the required sounds The identification of each faulted protection point should appear on the display. 5. Walk in front of any interior motion detectors (if used) and listen for the required sound as movement is detected. The identification of the detector should appear on the display when it is activated. Note: Wireless PIR (Passive Infrared) units will send signals out only if disturbed after they have been inactive for 3 minutes.

Other Displays dl:

If this remains displayed for more than 1 minute, your system is disabled. CALL FOR SERVICE IMMEDIATELY. CC: The system is in communication with the central station for change of function or status verification. If this message persists for more than 10 minutes, CALL YOUR SERVICE COMPANY. FC: A communication failure has occurred. CALL FOR SERVICE IMMEDIATELY. O C The keypad is not receiving signals from the control panel and sees an open circuit. If this message persists for more than 10 minutes, CALL YOUR SERVICE COMPANY.
FOR SERVICING INFORMATION, SEE PAGE 43

FIRE ALARM SYSTEM

IF INSTALLED
General Your fire alarm system (if installed) is on 24 hours a day, for continuous protection. In the event of an emergency, the strategically located smoke and heat detectors will automatically send signals to your system, triggering a loud, interrupted sound from the Keypad. An interrupted sound will also be produced by optional exterior sounders. A FIRE message will appear at your Keypad and remain on until you silence the alarm. 1. Should you become aware of a fire emergency before your detectors sense the problem, go to your nearest Keypad and manually initiate an alarm by pressing the panic key pair assigned as FIRE emergency (if programmed by the installer) as indicated on page 23. 2. Evacuate all occupants from the premises. 3. If flames and/or smoke are present, leave the premises and notify your local Fire Department immediately. 4. If no flames or smoke are apparent, investigate the cause of the alarm. The zone number(s) of the zone(s) in an alarm condition will be displayed at the Keypad.
TYPICAL "FIRE EMERGENCY" DISPLAY

In Case Of Fire Alarm

SUPV NO AC PHONE TEST NOT READY CHIME BAT INSTANT TAMPER

Silencing Fire Alarms

1. Silence the alarm by pressing the OFF key (security code not needed to silence fire alarms). To clear the display, enter your code and press the OFF key again (Memory of Alarm). 2. If the Keypad does not indicate a READY condition after the second OFF sequence, press the READY key to display the zone(s) that are faulted. Be sure to check that smoke detectors are not responding to smoke or heat producing objects in their vicinity. Should this be the case, eliminate the source of heat or smoke. 3. If this does not remedy the problem, there may still be smoke in the detector. Clear it by fanning the detector for about 30 seconds. 4. When the problem has been corrected, clear the display by entering your code and pressing the OFF key.

NATIONAL FIRE PROTECTION ASSOCIATION RECOMMENDATIONS ON SMOKE DETECTORS
General With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's Standard #74 noted below. Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the premises as follows: A smoke detector installed outside of each separate sleeping area, in the immediate vicinity of the bedrooms and on each additional story of the family living unit, including basements and excluding crawl spaces and unfinished attics. In addition, it is recommended that the owner consider the use of heat or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached garages.

TV ROOM KITCHEN

DINING

KITCHEN

BEDROOM BEDROOM

BDRM BDRM

BEDROOM

s LIVING ROOM s

LIVING ROOM
s Smoke Detectors for Minimum Protection Smoke Detectors for Additional Protection v Heat-Activated Detectors

LVNG RM

CLOSED DOOR GARAGE

BASEMENT

EMERGENCY EVACUATION

Steps to Safety

M ET OO OS DR CL BE
M OM OO TH RO DR BA ED B BE

2ND FLOOR

EN CH KIT BACK DOOR M OO DR BE

M OO TH DR BA BE

1ST FLOOR
Establish and regularly practice a plan of escape in the event of fire. The following steps are recommended by the National Fire Protection Association: 1. Plan on your detector or your interior and/or exterior sounders warning all occupants. 2. Determine two means of escape from each room. One path of escape should lead to the door that permits normal exit from the building. The other may be a window, should your path be unpassable. Station an escape ladder at such windows if there is a long drop to the ground. 3. Sketch a floor plan of the building. Show windows, doors, stairs and rooftops that can be used to escape. Indicate escape routes for each room. Keep these routes free from obstruction and post copies of the escape routes in every room. 4. Assure that all bedroom doors are shut while you are asleep. This will prevent deadly smoke from entering while you escape. 5. Try the door. If the door is hot, check your alternate escape route. If the door is cool, open it cautiously. Be prepared to slam the door if smoke or heat rushes in. 6. Crawl in the smoke and hold your breath. 7. Escape quickly; don't panic. 8. Establish a common meeting place outdoors, away from your premises, where everyone can meet and then take steps to contact the authorities and account for those missing. Choose someone to assure that nobody returns to the premises many die going back.

ONE SHORT BEEP (once every 40 seconds) Keypad only ONE BEEP every 40 sec. Keypad only TWO SHORT BEEPS Keypad only THREE SHORT BEEPS Keypad only
a. LOW BATTERY AT XMTR b. TROUBLE ARM AWAY OR MAXIMUM a. ARM STAY OR INSTANT b. ZONE OPENED WHILE SYSTEM IS IN CHIME MODE c. ZONE OPENED WHILE SYSTEM IS IN TEST MODE MEMORY OF ALARM ENTRY DELAY WARNING
a. BAT displayed with ID number of transmitter. b. CHECK displayed. Troubled protection zone is displayed. AWAY and (if MAXIMUM) INSTANT are displayed. a. STAY and (if INSTANT) INSTANT are displayed. Red ARMED indicator is lit. b. CHIME displayed. Pressing / READY key will display opened zone. c. Open protection zone number is displayed. FIRE and/or ALARM is displayed; zone in alarm is displayed. None during delay; Exceeding the delay time without disarming causes alarm.
RAPID BEEPING Keypad only SLOW BEEPING Keypad only
bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady ring. N o t e s : BAT displayed (with no beeping or zone number) indicates system main battery is weak (see page 27). Also see Power Failure, and Other Displays under TROUBLE CONDITIONS on page 27. 34

PROTECTION ZONES LIST

One or more sensing devices will have been assigned by the installer of your alarm system to each of the various protection zones in your system (although not every zone number can be used). For example, the sensing device on your Entry/Exit door may have been assigned to zone 06, sensing devices on windows in the master bedroom to zone 10, and so on. Zone numbers 07, 95 and 96 represent Keypad Keypad "Panic" alarm functions assigned by the installer (see Page 23). Zone numbers 08 and 09 are reserved for Duress and Tamper signal reporting to the central station. This chart may be used to record the specific zone number assignments for your system. Your installer will assist you in recording this information.
Zone Description Zone 33 PROTECTION ZONE DESCRIPTIONS Description Zone Description Zone 96 Description
Key B (or: & #) Panic Duress Tamper
Key A (or 1 & ) Panic Key C (or 3 & #) Panic
OWNER'S INSURANCE PREMIUM CREDIT REQUEST
This form should be completed and forwarded to your homeowner's insurance carrier for possible premium credit. A. GENERAL INFORMATION: Insured's Name and Address:__________________________________________________________________ __________________________________________________________________ Insurance Company:__________________________________ Policy No.: _____________________________ ADEMCO System: Type of Alarm: 4110DL Burglary

4110XM (circle one) Fire

Installed by: _________________________________ Serviced by: ___________________________________ _________________________________

address

___________________________________
B. NOTIFIES (Insert B for Burglary, F for Fire, where appropriate): Local Sounding Device ________ Police Dept. _______ Fire Dept. ______ Central Station _________
Name and Address:__________________________________________________________________________ C. POWERED BY: A.C. With Rechargeable Power Supply D. TESTING: Quarterly, Monthly, Weekly, Other _______________________________

continued on other side

OWNER'S INSURANCE PREMIUM CREDIT REQUEST (cont.)
E. SMOKE DETECTOR LOCATIONS: Furnace Room Basement Kitchen Living Room Bedrooms Dining Room Attic Hall
F. BURGLARY DETECTING DEVICE LOCATIONS: Front Door 1st Floor Windows Basement Door All windows Rear Door Interior Locations All Exterior Doors
All Accessible Openings, Including Skylights, Air Conditioners and Vents G. ADDITIONAL PERTINENT INFORMATION: _________________________________________________________________________________________ _________________________________________________________________________________________ _________________________________________________________________________________________ _________________________________________________________________________________________
Signature: ____________________________________________________ Date: _______________________
CANADIAN DEPARTMENT OF COMMUNICATIONS (DOC) STATEMENT

NOTICE

The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company's inside wiring associated with a single line individual service may be extended by means of certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Caution: User should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all the devices does not exceed 100.

This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company. This equipment uses the following jacks: An RJ31X is used to connect this equipment to the telephone network. The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area. (continued) 40
(continued) FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 STATEMENT If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe necessary. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service. If trouble is experienced with this equipment, please contact the manufacturer for repair and warranty information. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved. There are no user serviceable components in this product, and all necessary repairs must be made by the manufacturer. Other repair methods may invalidate the FCC registration on this product. This equipment cannot be used on telephone company-provided coin service. Connection to Party Line Service is subject to state tariffs. This equipment is hearing-aid compatible. When programming or making test calls to an emergency number, briefly explain to the dispatcher the reason for the call. Perform such activities in the off-peak hours; such as early morning or late evening.

IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS
If your security system has been connected to the telephone line, and there is trouble with regular telephone service, disconnect the security system from the telephone line by removing the plug from the RJ31X (CA38A in Canada) telephone wall jack (you should have been shown how to do this by your installing company). Do not attempt to disconnect the telephone line connection inside the control cabinet. Doing so will result in the COMPLETE disruption of your regular telephone service. If the regular phone works correctly after the plug has been disconnected from the RJ31X wall jack, the security system has a problem and you should call your service representative for service immediately. If, upon disconnection of the security system from the wall jack, there is still a problem with telephone service, notify the telephone company that they have a problem and request prompt repair service. IMPORTANT: A security system connected to an alarm monitoring station relies on that connection. If the security system is at fault, reinsert the plug as soon as the security system is repaired. If the phone service is at fault, re-insert the plug immediately, to ensure resumption of full protection upon restoration of phone service. The user may not, under any circumstances (in or out of warranty), attempt any service or repairs to the system.
WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example: Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. A user may not be able to reach a panic or emergency button quickly enough. While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death. Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90 to 105F (32 to 40C), the detection performance can decrease.

(continued) WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers. Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the situation. In the case of a monitored alarm system, authorities may not respond appropriately. This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. Wireless transmitters (used with some systems) are designed to provide long battery life under normal operating conditions. Longevity of batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device being used. External factors such as humidity, high or low temperatures, as well as large swings in temperature, may all reduce the actual battery life in a given installation. This wireless system, however, can identify a true low battery situation, thus allowing time to arrange a change of battery to maintain protection for that given point within the system. Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments.

SERVICING INFORMATION

Your local authorized service representative is the person best qualified to service your alarm system. Arranging a regular program with that person is advisable. Your local service representative is:

Previous Menu

SECURITY SYSTEM

4110DL
ANT PORT R IM N!! ER FO ORMATIO COV NF SIDE IN AND I SEE RES EATU F NEW
Installation Instructions Installation Instructions Installation Instructions

N5672V3 10/96

Please Read
INFORMATION CONCERNING NEW FEATURES Controls with microprocessor part number N7185V3 or higher contain the following new features. These controls can be identified via the downloader as Rev. 06.
1. This control complies with National Fire Protection Association (NFPA) requirements for temporal pulse sounding of fire notification appliances. Fire alarms now sound as interrupted pulses consisting of three pulses and a brief pause (i.e. ring, ring, ring, pause ring, ring, ring, pause, etc.) Capability has been added for the control to call a pager on the secondary telephone number. This can only be used if the primary reporting format is Ademco Contact ID. The following entries have been added to program field *49 (Split/Dual Reporting) for the purpose of paging messages: Primary 6 = All reports except Open/Close 7 = All reports 8 = All reports Touch-tone codes sent to the pager are: 1911 = Alarm 1001 = Open 1002 = Close 1811 = Trouble No restore reports are sent to the pager. 3. 4. 5. 6. Three additional user codes have been added (identified as Users 5, 6, and 7). Duress is now User 8 (no longer User code + 1). AC Loss report is now sent at a random time delay up to 1 hour. If AC is restored before the report goes out, no report will be sent. Telephone number entries can now contain *, #, and a 2-second pause. Enter # + 11 for "*" Enter # + 12 for "#" Enter # + 13 for 2-sec. pause Audible Exit Warning option has been added (field *27: 0 = no; 1 = yes [default = 1]). If enabled, beeping will occur during exit time and will change from slow to rapid beeping during last 5 seconds of exit delay. Master code is now able to change itself in normal operating mode. To change, enter: [Master code] + [8] + [1] + [new Master code] + [new Master code] again. New Telco Hand-off feature allows the technician at the site to call the downloading facility from the control panel phone line, initiate a site download (Master Code + # +1), and the control will immediately be on-line with the modem at the downloading facility. If all power is lost at the control, upon power up, the armed status will be the same as it was before the power loss. Bypasses, however, are not retained. The control checks for the physical battery connection every two minutes. If connection is lost, a visual and audible trouble is indicated, and a communicator report will be sent (if programmed). The actual condition of the battery is still checked once every four hours. To clear the low battery message after the low battery condition is restored, enter Test mode: [User code] + [5]; otherwise it will clear itself the next time the system checks the battery's condition. Secondary (Paging number) Alarms/ Open/Close, Troubles Alarms, Troubles Alarms, Open/Close, Troubles

7. 8. 9.

10. 11.

TABLE OF CONTENTS

RECOMMENDATIONS FOR PROPER PROTECTION.. 5 Section 1. GENERAL DESCRIPTION... 6 FEATURES... 6 SPECIFICATIONS... 6 COMPATIBLE DEVICES... 6 ZONE RESPONSE TYPE CHARACTERISTICS.. 7 WIRING GUIDELINES... 7 Section 2. SYSTEM INSTALLATION AND WIRING.. 8 Section 3. PROGRAMMING THE SYSTEM... 9 THE MECHANICS OF PROGRAMMING.. 9 Entering Program Mode... 9 Programming a Data Field... 9 Reviewing a Data Field... 9 Erasing an Entry in a Data Field.. 9 Downloading.... 9 Clearing All Data Fields... 9 Exiting Program Mode.. 9 Section 4. SYSTEM OPERATION... 10 USER ACCESS CODES... 10 Adding a Secondary User Code.. 10 Deleting a Secondary User Code.. 10 KEYPAD FUNCTIONS... 10 System Commands... 10 Panic Keys... 10 Keyswitch LED Indications.. 10 Keyswitch Operation... 10 Section 5. TESTING THE SYSTEM... 11 REGULATORY AGENCY STATEMENTS.. 12 DOC STATEMENT... 13 THE LIMITATIONS OF THIS ALARM SYSTEM.. 14 SUMMARY OF CONNECTIONS DIAGRAM. INSIDE BACK COVER ADEMCO LIMITED WARRANTY.. BACK COVER

RECOMMENDATIONS FOR PROPER PROTECTION
The Following Recommendations For The Location Of Fire And Burglary Detection Devices Help Provide Proper Coverage For The Protected Premises.
Recommendations For Smoke And Heat Detectors
With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's (NFPA) Standard #72 noted below. Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows: For minimum protection a smoke detector should be installed outside of each separate sleeping area, and on each additional floor of a multi-floor family living unit, including basements. The installation of smoke detectors in kitchens, attics (finished or unfinished), or in garages is not normally recommended. For additional protection the NFPA recommends that you install heat or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached garages. In addition, we recommend the following: Install a smoke detector inside every bedroom where a smoker sleeps. Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway outside may not wake up the sleeper if the door is closed. Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air conditioners or humidifiers) are used. Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters) long. Install smoke detectors in any room where an alarm control is located, or in any room where alarm control connections to an AC source or phone lines are made. If detectors are not so located, a fire within the room could prevent the control from reporting a fire or an intrusion.

DINING KITCHEN

TV ROOM

BEDROOM BEDROOM

KITCHEN

DINING

BDRM BDRM

s LIVING ROOM 7 s

LIVING ROOM

BEDROOM

s Smoke Detectors for Minimum Protection 7 Smoke Detectors for Additional Protection v Heat-Activated Detectors 7

LVNG RM

CLOSED DOOR GARAGE

BASEMENT

Recommendations For Proper Intrusion Protection
For proper intrusion coverage, sensors should be located at every possible point of entry to a home or commercial premises. This would include any skylights that may be present, and the upper windows in a multi-level building. In addition, we recommend that radio backup be used in a security system so that alarm signals can still be sent to the alarm monitoring station in the event that the telephone lines are out of order (alarm signals are normally sent over the phone lines, if connected to an alarm monitoring station).

Section 1. GENERAL DESCRIPTION
The 4110DL is a microprocessor-based state-of-the-art security controls intended for wired applications. The Control Panel supports up to 6 hardwired zones and can be programmed either through the keypad or remotely using ADEMCO's V-LINK downloading software.

FEATURES

Zones Supported
6 hardwire zones, characteristics: having the following

Alarm Output

Provides a 12VDC, 2 AMP output (assumes a fully charged battery is connected) Steady output for Burglary/Panic, or pulsing output for Fire Output is current limited
EOLR supervision supporting N.O. or N.C. sensors. 300-500 msec normal response. Zone 3 programmable for Fast Response to open (10mS).

Communication Formats

Ademco Low Speed (Standard or Expanded): 1400Hz ACK/KISSOFF. Sescoa/Radionics (Standard or Expanded): 2300Hz ACK/KISSOFF. Ademco Express : DTMF, 1400/2300Hz ACK, 1400Hz KISSOFF. Ademco Contact ID: DTMF 1400/2300Hz ACK, 1400Hz KISSOFF.

Security Codes

1 master code for entire system (user 1) 3 secondary user codes (users 2-4)

Keypad Panic Keys

Provides 3 panic key functions

SPECIFICATIONS

4110DL CONTROL
1. Physical: 12-1/2" W x 14-1/2" H x 3" D (318mm x 368mm x 76mm) Electrical: VOLTAGE INPUT: 16.5VAC from plug-in 25VA transformer, Ademco No. 1321/TF2 (in U.S.A.), 1321CN (in Canada) RECHARGEABLE BACK-UP BATTERY: 12VDC, 4AH (Gel type). CHARGING VOLTAGE : 13.8VDC. ALARM SOUNDER: 12V, 2.0 Amp output AUXILIARY POWER OUTPUT : 12VDC, 500mA max. Interrupts for 4-wire smoke detector reset. MAXIMUM ZONE RESISTANCE: Zones 1-8 = 300 ohms excluding EOLR
In UL installations, maximum current draw from the Auxiliary Output and the Alarm Output combined must not exceed 500mA total.
FUSE : Battery (3A) No. 90-12 LINE SEIZE: Double Pole REGULATORY INFORMATION Ringer Equivalence: 0.7B FCC Registration No.: AC 398U-68192-AL-E UL File No. S1632, Guide UXOU

COMPATIBLE DEVICES

Remote Keypads (up to 4)
Model 4127, 6127 4137AD, 6137, (Select for Vista) Type Fixed English Fixed English Addressable Alpha

IMPORTANT

Addressable keypads must be used in the non-addressable mode (Device Address 31), which is pre-set at the factory. Do not set these keypads to any other addresses.
Smoke Detectors (4-wire only) Model

2412TH

Ionization Products of Combustion Detector Photoelectric Smoke Detector Photoelectric Smoke Detector)w/135 F (57 C) Heat Detector)

Fire Supervisory Module

A77-71601 EOL Relay Module (supervises power for 4 wire fire zone).

Optional Keyswitch

4116 Keyswitch
ZONE RESPONSE TYPE CHARACTERISTICS

Zone Response Type

1 Entry/Exit Burglary 5 Trouble by Day/Alarm by Night 6 24-Hr. Silent Alarm Hr. Audible Alarm 8 24-Hr. Auxiliary Alarm 9 Fire

Characteristics

Provides exit delay time when panel is armed in any arming mode. Provides entry delay when panel is armed in Away and Stay modes only. Provides an instant alarm when panel is armed in any arming mode. Provides exit delay time when panel is armed in any mode. Will only provide entry delay if an Entry/Exit zone is faulted first upon entry. Otherwise, alarm will be instant. Bypassed automatically when panel is armed in the Stay or Instant mode. Provides a trouble response if panel is not armed when zone is faulted. Provides an instant alarm if panel is armed in any mode. Provides a silent alarm to Central Station whether panel is armed or disarmed. Provides an audible alarm at the bell output and keypad whether panel is armed or disarmed. Provides an audible alarm at the keypad only. No bell output is provided. Provides a fire alarm when zone is shorted. Causes bell output to pulse. Provides a trouble response when zone is open. Provides entry and exit delay times. Bypassed automatically when panel is armed in the Stay or Instant mode.
3 Perimeter Burglary 4 Interior, Follower

10 Interior w/Delay

WIRING GUIDELINES
Wiring Run Chart For Devices* Drawing Aux Power From The Control (12V+ & GND) TOTAL CURRENT DRAWN BY ALL DEVICES CONNECTED TO A SINGLE WIRE RUN Wire Size #22 #20 #18 #mA or less 500 ft (152m) 750 ft (228.6m) 1300 ft (396m) 1500 ft (457m) 100 mA 250 ft (76m) 380 ft (116m) 650 ft (198m) 1000 ft (305m) 300 mA 80 ft (24m) 130 ft (39.6m) 220 ft (67m) 330 ft (100.5m) 500 mA 50 ft (15m) 80 ft (24m) 130 ft (39.6m) 200 ft (70m)
* Includes Keypads and alarm devices requiring separate power.
Example: If you have two motion detectors that draw a total of 44 mA, and you are using #20 AWG wire, the distance from the control panel Aux + and - terminals to the last device can be up to 750 ft. The length of all wire runs for keypads must not exceed 1500 feet (457m) when unshielded quad conductor cable is used (750 feet if shielded cable is used). This restriction is due to the capacitive effect on the data lines when quad cable is used.
Transformer Wiring Table Distance of Transformer From the Control Panel Up to 50 feet 50100 feet 100250 feet Wire Gauge To Use # 20 # 18 # 16
Section 2. SYSTEM INSTALLATION AND WIRING

INSTALLING THE SYSTEM

Refer to the Summary of Connections diagram on the inside back cover of this manual for terminal connections when following these procedures. 1. 2. Mount the Control Cabinet. Mount the PC board. BE SURE TO USE THE PLASTIC MOUNTING CLIPS (SUPPLIED) TO ISOLATE THE CIRCUIT BOARDS FROM THE CABINET. FAILURE TO DO SO MAY RESULT IN DAMAGE TO THE TRANSFORMER AND/OR THE CIRCUIT BOARDS.

WARNING

3. 4. 5.
Install Remote Keypads. Install Hardwired Zones. Install Sounding Devices.
Use only UL Listed sounding devices for UL installations.
Install the Remote Keyswitch. Connect Telephone Line. Make sure telephones on the premises are connected only through the alarm control panel (disconnect from the incoming phone line at the telephone jack). This is necessary to have true line seizure.
Connect the AC Transformer. DO NOT PLUG THE TRANSFORMER INTO THE AC OUTLET UNTIL ALL OTHER WIRING TO THE CONTROL IS COMPLETE.
Connect the Battery. Do not attach the connector cable to the battery's terminals until after you have plugged the AC transformer into an uninterrupted 120VAC outlet. 1. 2. In UL installations, maximum current draw from the Auxiliary Output and the Alarm Output combined must not exceed 500mA. Use a 3A battery or larger for UL installations.

Connect Earth Ground.

Section 3. PROGRAMMING THE SYSTEM
THE MECHANICS OF PROGRAMMING
For actual program fields, refer to the programming form included at the center of this manual. Entering Program Mode Use one of the following methods: Press both the [*] and [#] keys at the same time within 50 seconds after power is appled to the Control. or After power-up, enter the [Master Code] + 8 + 0 (default Master Code is 4110) This method is disabled if you exit the program mode using *98 instead of *99. See "Exiting Program Mode" later in this section. Once you have entered program mode, data field *20 will be displayed (this is the first field in the system). The system will now accept entries for field *20. Programming a Data Field Field Number 20
Press [*] plus [Field No.] (e.g., *20), and then make the required entry. Note the following: The keypad beeps three times when the data field has been completely programmed The next Field No. is displayed. If you do not want to program this field, press [*] + the Field No. you want to program. If the number of digits that you need to enter in a data field is less than the maximum digits available (e.g., the phone number field), enter the desired data, then press [*] + the next Field No. to be programmed. If you try to enter a non-existent field, the keypad will display EE or Entry Error. Simply re-enter [*] plus a valid Field No. Reviewing a Data Field Press [#] plus [Field No. ]. Note the following: Data will be displayed for that field number, entry by entry (a beep will be heard between entries and three beeps after the last). No changes will be accepted in this mode. If you try to enter a non-existent field, the keypad will display EE or Entry Error. Simply re-enter [#] plus a valid field number.

Erasing an Entry in a Data Field Applies only to fields *40-*43, and *94. Press [*] plus Field No. plus [*]. Downloading *96 resets the Subscriber Account number and CSID in preparation for an initial download. If *97 was entered previously, *96 must be entered last. Clearing All Data Fields *97 clears (zeros) all data fields. The Master Code will now be 0 0. DO NOT PRESS *97 IF ANY PROGRAMMING HAS BEEN DONE PREVIOUSLY; DATA ALREADY PROGRAMMED INTO THE SYSTEM WILL BE DELETED.
Exiting Program Mode *98 inhibits re-entry into the programming mode with the use of the Master Code. *99 allows re-entry into the program mode using Master Code + 8 + 0.
Section 4: SYSTEM OPERATION

USER ACCESS CODES

Adding a Secondary User Code MASTER CODE + [CODE KEY] + USER # ( 2, 3, OR 4) + DESIRED 4-DIGIT ACCESS CODE. (The system will emit a single beep when a secondary code has been successfully entered.) Deleting a Secondary User Code MASTER CODE + [CODE KEY] + USER # (2, 3 OR 4) Notes: All Master and Secondary security codes permit access to the system for arming, disarming, etc. If a secondary code is inadvertently repeated for different users, the lower user number will take priority. Opening and closing reports are sent for the Master as No. 1. User codes are sent as Numbers 2, 3, and 4, respectively.

KEYPAD FUNCTIONS

System Commands Before arming, the system must be in the READY condition (all zones must be intact). If the "NOT READY" message appears, press the READY [* ] key to display faulted zones. SUMMARY OF SYSTEM COMMANDS
MODE AWAY STAY INSTANT MAXIMUM DISARM BYPASS QUICK BYPASS (if enabled) CHIME MODE SITE-INITIATED DOWNLOAD* HOW TO PERFORM Security Code + [2] Security Code + [3] Security Code + [7] Security Code + [4] Security Code + [1] Security Code + [6] + Zone #(s) Security Code + [6] Security Code + [9] (toggles on and off) Security Code + [#] + [1] EXIT DELAY Yes Yes Yes Yes ENTRYDELAY Yes Yes No No PERIMETER ARMED Yes Yes Yes Yes INTERIOR ARMED Yes No No Yes
* Initiates phone call to the downloading facility. Panic Keys
A panic function is activated when: Both keys of the appropriate key pair are pressed at the same time, or The appropriate lettered key is pressed for at least 2 seconds. The panic functions are identified by the system as follows:

Keys [1] & [*], or [A] [ *] & [#], or [B] Displayed as Zone Zone Type 24-Hr. Silent Programmable (24-Hr. Silent, Audible, Auxiliary, or Fire 24-Hr. Audible
Notes: Keys [A], [B], [C] are not on all keypads. Key [D], if present, is not active here.

[3] & [#], or [C]

Keyswitch LED Indications
RED OFF SLOW FLASH RAPID FLASH MEANING DISARMED & NOT READY ARMED READY ARMED
Keyswitch Operation To arm AWAY, turn key and release within a 1/2 second. To arm STAY, turn and hold key for longer than 2 seconds. To disarm, turn key and immediately release.
Section 5. TESTING THE SYSTEM
After installation is completed, the Security System should be carefully tested, as follows: Test Mode 1. With the system in the disarmed state, check that all zones are intact. If a NOT READY message is displayed, press the [ D] key to display the faulted zone(s). Restore faulted zone(s) if necessary. 2. Enter the [Security Code] + [5] TEST. The following will occur: The outside sounder will sound for 1 second. A test report will be transmitted (if programmed) to the Central Station immediately. (If the backup battery is discharged or missing, the sounder may not turn on and a LOW BATTERY report will be transmitted with a TEST report.) 3. Fault and restore each zone. The keypad will emit 3 beeps each time a contact is faulted. The keypad will beep once per minute as a reminder that the system is in the Test Mode. 4. Exit this mode by entering the [Security Code] + [1] OFF.
Armed System Test Alarm messages will be sent to the central station during the following tests. Notify them in advance that tests will be in progress. 1. 2. 3. Arm the system and fault one or more zones. After 15 seconds (if optional dialer delay is selected), silence alarm sounder(s) by entering the [Security Code] + [1] OFF. Check Entry/Exit delay zones. Check the keypad-panic alarms that are in the system by pressing the Panic key (key pairs on some keypads). If the system has been programmed for audible emergency, the keypad will emit a steady alarm sound, and ALARM and [Zone Number] will be displayed. Silence the alarm by entering the [Security Code] and pressing OFF. If the system has been programmed for silent emergency, there will be no audible alarms or displays, but a report will be sent to the central station. Notify the central station when all tests are finshed, and verify results with them.

TO THE INSTALLER Regular maintenance and inspection (at least annually) by the master and frequent testing by the user are vital to continuous satisfactory operation of any alarm system. The master should assume the responsibility of developing and offering a regular maintenance program to the user as well as acquainting the user with the proper operation and limitations of the alarm system and its component parts. Recommendations must be included for a specific program of frequent testing (at least weekly) to insure the system's proper operation at all times.
REGULATORY AGENCY STATEMENTS
UL NOTICE: This is a "Grade A" residential system.
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: If using an indoor antenna, have a quality outdoor antenna installed. Reorient the receiving antenna until interference is reduced or eliminated. Move the radio or television receiver away from the receiver/control. Move the antenna leads away from any wire runs to the receiver/control. Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user or master may find the following booklet prepared by the Federal Communications Commission helpful: "Interference Handbook" This booklet is available from the U.S. Government Printing Office, Washington, DC 20402. The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.

FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 STATEMENT
This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this in formation must be provided to the telephone company. This equipment uses the following jacks: An RJ31X is used to connect this equipment to the telephone network. The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe necessary. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the neces sary modifications in order to maintain uninterrupted service. If trouble is experienced with this equipment, please contact the manufacturer for repair and warranty information. If the trou ble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved. There are no user serviceable components in this product, and all necessary repairs must be made by the manufacturer. Other repair methods may invalidate the FCC registration on this product. This equipment cannot be used on telephone company-provided coin service. Connection to Party Line Service is subject to state tariffs. This equipment is hearing-aid compatible. When programming or making test calls to an emergency number, briefly explain to the dispatcher the reason for the call. Perform such activities in the off-peak hours; such as early morning or late evening.
CANADIAN DEPARTMENT OF COMMUNICATIONS (DOC) STATEMENT NOTICE The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company's inside wiring as sociated with a single line individual service may be extended by means of certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or al terations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Caution: User should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the require ment that the total of the Load Numbers of all the devices does not exceed 100.

WARNING THE LIMITATIONS OF THIS ALARM SYSTEM
While this System is an advanced design security system, it does not offer guaranteed protection against burglary, fire or other emergency. Any alarm system, whether commercial or residential, is sub ject to compromise or failure to warn for a vari ety of reasons. For example: Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will not work with out power. Battery-operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. A user may not be able to reach a panic or emergency button quickly enough. While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for ex ample, may not sense a first floor or basement fire. Finally, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending on the nature of the fire and/or location of the smoke detectors, the detector, even if it operates as anticipated, may not pro vide sufficient warning to allow all occupants to escape in time to prevent injury or death. Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tamper ing, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detec tion ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of the protected area approaches the temperature range of 90 to 105F (32 to 40C), the detection performance can decrease. Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices are located on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo, radio, air conditioner or other appliance, or by passing traffic. Fi nally, alarm warning devices, however loud, may not warn hearing-impaired people. Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. Even if the system responds to the emergency as intended, however, occupants may have insuffi cient time to protect themselves from the emergency situation. In the case of a monitored alarm sys tem, authorities may not respond appropri ately. This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 20 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. The security keypad (and remote keypad) should be tested as well. Wireless transmitters (used in some systems) are designed to provide long battery life under normal operating conditions. Longevity of batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device being used. External factors such as humidity, high or low temperatures, as well as large swings in temperature, may all reduce the actual battery life in a given installation. This wireless system, however, can identify a true low battery situation, thus allowing time to arrange a change of battery to maintain protection for that given point within the system. Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments.

GEL LEAD ACID TYPE. DO NOT USE GATES BATTERY BATTERY NORMALLY NEED NOT BE REPLACED FOR AT LEAST 3 YRS. BATTERY CAPACITY FOR EMERGENCY STANDBY USE AT LEAST 4 HOURS.
FUSE FOR REPLACEMENT, USE SAME VALUE

AUX PWR OUTPUT TERMS

BATTERY (e.g. No. 90-12) CHARGING VOLTAGE 13.8VDC
EOL POWER SUPERVISION RELAY MODULE A77-716B
4-WIRE SMOKE OR COMBUSTION DETECTOR
BATTERY 12V, 4AH OR 12V, 1.2AH

BLACK RED

VIOLET
CONNECTOR TABS TO DETERMINE TOTAL STANDBY LOAD ON BATTERY, ADD 100mA TO TOTAL OF AUX. POWER OUTPUT AND REMOTE CONSOLE CURRENTS. USE UL LISTED LIMITED ENERGY CABLE FOR ALL CONNECTIONS
BLK RED GRN YEL OPTIONAL No. 4116 ARMING/DISARMING KEYSWITCH (SINGLE LED, LOCKSWITCH, TAMPER)

HEAT DETECTOR

1000 OHMS EOLR
ZONE 5 (IF PROGRAMMED FOR FIRE)
LOCATED AT LOWER RIGHT CORNER OF CIRCUIT BOARD
YELLOW: DATA OUT TO CONSOLE
GREEN: DATA IN FROM CONSOLE
FOR COMPLETE INFORMATION, SEE INSTRUCTIONS N5672VS
BLACK: CONSOLE GROUND () RETURN

ZONE 5

ZONE 3

ZONE 1

ZONE 2

ZONE 4

ZONE 6
TO 110VAC UNSWITCHED OUTLET (24HR)
PLUG-IN TRANSFORMER 16.5VAC, 25VA (e.g. ADEMCO No. 1321/TF2. USE No. 1321CN IN CANADA
NOTE: CONSOLE CURRENT MUST BE INCLUDED IN AUX. CURRENT DRAIN CALCULATIONS

RED: CONSOLE PWR (+)

AUX. POWER OUTPUT 10.5-13.8VDC 500mA MAX. INTERRUPTS FOR FIRE ALARM RESET
ALARM OUTPUT 10.5-13.8VDC, 2A MAX. (600mA MAX FOR UL USAGE, INCLUDING AUX. POWER) STEADY FOR BURGLARY/PANIC, PULSING FOR FIRE (e.g. USE ADEMCO No. 702 OR 719 SIREN, OR 12V BELL) CONNECTION OF THE FIRE ALARM SIGNAL TO A FIRE ALARM HEADQUARTERS OR A CENTRAL STATION SHALL BE PERMITTED ONLY WITH THE PERMISSION OF THE LOCAL AUTHORITY HAVING JURISDICTION. THE BURGLAR ALARM SIGNAL SHALL NOT BE CONNECTED TO A POLICE EMERGENCY NUMBER.
REMOTE CONSOLE No. 4127: No. 4137AD: No. 6127: No. 6128: No. 6137: OR No. 5330: 20mA 60mA 20mA 30mA 85mA 105mA
NOTE: MULTIPLE CONSOLES MAY BE USED, BUT EACH 5330 CONSOLE MUST BE ON AN INDIVIDUAL HOME RUN. USE MAX. OF 220FT. OF #22 WIRE OR 550 FT. OF #18 WIRE.
No. 4110DL SUMMARY OF CONNECTIONS

TIP (BROWN)

RING TIP (GRAY) (GREEN)

RING (RED)

OHMS OHMS OHMS OHMS OHMS OHMS EOLR EOLR EOLR EOLR EOLR EOLR MAXIMUM LOOP RESISTANCE (EACH ZONE) 300 OHMS (PLUS EOLR) RESPONSE, ZONES 1-6: 300-500MSEC ZONE 3 CAN BE PROGRAMMED FOR N.C. SENSOR FAST RESPONSE TO AN OPEN: 10MSEC MAX ZONE 5 CAN BE PROGRAMMED FOR USE AS A FIRE ZONE. SEE DIAGRAM THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) IT MAY NOT CAUSE HARMFUL INTERFERENCE, (2) IT MUST ACCEPT ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. COMPLIES WITH FCC RULES, PART 68 FCC REGISTRATION NO. AC398U-68192-AL-E RINGER EQUIVALENCE: 0.7B.

WARNING:

WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM.
THIS EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATIONS STANDARD 74 (NATIONAL FIRE PROTECTION ASSOC., BATTERYMARCH PARK, QUINCY, MA 02269). PRINTED INFORMATION DESCRIBING PROPER INSTALLATION, OPERATION, TESTING, MAINTENANCE, EVACUATION PLANNING AND REPAIR SERVICE IS TO BE PROVIDED WITH THIS EQUIPMENT.
HANDSET INCOMING PHONE LINE EARTH GROUND SEE INSTRUCTIONS FOR PROPER GROUNDING TELEPHONE WIRING (VIA RJ31X* JACK DIRECT CONNECT CORD) *IN CANADA, CA38A JACK

DOC LOAD NO.: 3

TO PREVENT RISK OF SHOCK, DISCONNECT TELEPHONE LINE AT TELCO JACK BEFORE SERVICING THIS UNIT.
ADEMCO LIMITED WARRANTY Alarm Device Manufacturing Company, a Division of Pittway Corporation, and its divisions, subsidiaries and affiliates ("Seller"), 165 Eileen Way, Syosset, New York 11791, warrants its products to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for 24 months from the date stamp con trol on the product or, for products not having an Ademco date stamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply. Seller's obligation shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product which is proved not in compli ance with Seller's specifications or proves defective in materials or workmanship under normal use and service. Seller shall have no obligation un der this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Ademco factory service. For warranty service, return product transportation prepaid, to Ademco Factory Service, 165 Eileen Way, Syosset, New York 11791. THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. Seller does not represent that the products it sells may not be compromised or circumvented; that the products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the products will in all cases provide adequate warning or protection. Customer un derstands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LI ABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UN DER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty replaces any previous warranties and is the only warranty made by Seller on this product. No increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorized.