Away Stay Part. 1 Away Stay Part. 2 Away Stay Common
67 RF Trans. Low Bat Report Code
UL: must be enabled if wireless devices are used

[00] [00]

50 Burglary Dialer Delay

68 Cancel Report Code

V20PSIA/V15PSIA: [10] Report enabled.
Delay Time: Delay Time V20PSIA/V15PSIA 0 = no delay UL: must be 0 Delay Disable 1 = 15 seconds; 2 = 30 seconds; 3 = 45 seconds SIA Guidelines: delay must be minimum of 30 seconds V20PSIA/V15PSIA: Delay Time: 1 = 15 seconds; 2 = 30 seconds; 3 = 45 seconds Delay Disable: 0 = use delay set in entry = dial delay disabled for zones listed in zone list 6 (use zone list 6 to enter those zones that require dial delay to be disabled; these zones ignore the setting in entry 1) UL: Dial delay plus entry delay must not exceed one minute; use zone list 6 to disable dial delay from appropriate zones, if necessary.
69 Recent Closing Report Code
V20PSIA/V15PSIA: Always enabled. Field does not apply to other controls.
RESTORE REPORT CODES (70 76) 70 Alarm Restore Rpt Code
[0] [00] [00] [00] [00] [00] [00] | | | | | |
71 Trouble Restore Rpt Code 72 Bypass Restore Rpt Code 73 AC Restore Rpt Code 74 Low Bat Restore Rpt Code 75 RF Trans. Lo Bat Rst Rpt Code
53 SESCOA/Radionics Select 54 Dynamic Signaling Delay 55 Dynamic Signaling Priority
0 = Radionics (0-9, B-F); enter 0 for all non-SESCOA formats 1 = SESCOA (0-9 only reporting)
Select delay from 0 to 225 secs, in 15-sec increments. 0 = no delay (both signals sent); 1 = 15 secs; 2 = 30 secs, etc. UL: Grade AA must be 0; Grade A must be 15 max
0 = Primary Dialer first; 1 = Long Range Radio first. For UL Commercial Burglary installations that use a DACT and LRR, this field must be 0.
76 Test Restore Rpt Code 77 Daylight Savings Time

Start/End Month

0 = Disabled 1-12 = January-September (1 = Jan, 2 = Feb, etc) #+10 = October; #+11 = November; #+12 = December
OUTPUT AND SYSTEM SETUP (77 93)

[4][10] |

56, 57, 58 Menu Modes
These are Menu Mode commands, not data fields, for Zone Programming, Function Key Programming, and Expert Mode Zone Programming respectively. See page 2 and respective sections later in this document.
TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES (59 thru 68, *70 thru 76, and 89): For 3+1 or 4+1 Standard Format: Enter a code in the first box: 19, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F. A 0 (not #+10) in the first box will disable a report. A 0 (not #+10) in the second box will result in automatic advance to the next field. For Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 19, 0, or BF, as described above. A 0 (not #+10) in the second box will eliminate the expanded message for that report. A 0 (not #+10) in both boxes will disable the report. For Ademco Contact ID Reporting: Enter any digit (other than 0) in the first box, to enable zone to report (entries in the second boxes are ignored). A 0 (not #+10) in the first box disables the report. UL: see installation instructions for requirements

78 Daylight Savings Time

Start/End Weekend

[1][5]

0 = disabled; 1 = first; 2 = second; 3 = third; 4 = fourth; 5 = last; 6 = next to last; 7 = third to last
79, *80, *81, *82 Menu Modes
These are Menu Mode commands, not data fields, for Output Device Mapping, Output Programming, Zone List Programming, and Alpha Programming respectively. See page 2 and their respective sections in the Installation and Setup Guide for procedures.
84 Auto Stay Arm 85 Cross Zone Timer

[3] [0]

SYSTEM STATUS REPORT CODES (59 68) [0] 59 Exit Error Alarm Report Code
See above for entries. V20PSIA/V15PSIA: [1] Always enabled.
0 = no; 1 = partition 1 only; 2 = partition 2 only; 3 = both partitions
60 Trouble Report Code 61 Bypass Report Code 62 AC Loss Report Code 63 Low Bat Report Code 64 Test Report Code

[00] [00] [00] [00] [00]

| | | | |
This option not for use in UL installations. (assign cross zones on zone list 4, using *81 Menu mode) 0 = 15 seconds 6 = 2-1/2 min #+12 = 8 min 1 = 30 seconds 7 = 3 min #+13 = 10 min 2 = 45 seconds 8 = 4 min #+14 = 12 min 3 = 60 seconds 9 = 5 min #+15 = 15 min 4 = 90 seconds #+10 = 6 min 5 = 2 minutes #+11 = 7 min
86 Cancel Verify Keypad Display
0 = no alarm canceled display 1 = display Alarm Canceled when system is disarmed after an alarm has occurred. (To clear the ALARM CANCELED display, the user must enter the security code + OFF again.)
Use Scheduling mode to set periodic test reports, or use the following key commands: installer code +[#] + [0] + 0 = test report sent every 24 hours installer code +[#] + [0] + 1 = test report sent once per week installer code +[#] + [0] + 2 = test report sent every 28 day Each mode sets schedule 32 (VISTA-20P) or schedule 08 (VISTA-15P) to the stated repeat option; first test report sent 12 hours after command.
87 Misc. Fault Delay Time

65 Open Report Code

[0,0,0]

Part. 1 Part. 2 Common

(used with Configurable Zone Types digit 6) 0 = 15 seconds 6 = 2-1/2 min #+12 = 8 min 1 = 30 seconds 7 = 3 min #+13 = 10 min 2 = 45 seconds 8 = 4 min #+14 = 12 min 3 = 60 seconds 9 = 5 min #+15 = 15 min 4 = 90 seconds #+10 = 6 min 5 = 2 minutes #+11 = 7 min UL: may only be used on non-burglar alarm/ non-fire alarm zones when used in fire and/or UL burglar alarm installation

164 Pager 2 Characters

UL: see Inst. Instructions for requirements NOTE: Output Device must either be programmed to be STOPPED in field 80 or STOPPED by Code + # + 8 + output number. Entry 1:: 0 = disabled, 1-15 = 1 min - 15 min (#+10 = 10 min; #+11 = 11 min; #+12 = 12 min; #+13 = 13 min; #+14 = 14 min; #+15 = 15 min) Entry 2: 0 = Keypad display when line is faulted 1 = Keypad display plus keypad trouble sound 2 = Same as 1, plus programmed output device STARTS. If either partition is armed, external sounder activates also.
165 Pager 2 Report Options
Part. 1 Part. 2 common See field *162 for reporting options. Select for each partition (use zone list 10 if using options 12 or 13).
93 Reports In Armed Period
Restrict V20PSIA/V15PSIA Report Pairs Unlimited Reports Enable

166 Pager 3 Phone No.

Per Zone (Swinger Suppression)
Restrict Report Pairs: 0 = Unlimited Reports 1 = 1 report pair 2 = 2 report pairs SIA Guidelines: Must be set for option 1 or 2.

167 Pager 3 Characters

V20PSIA/V15PSIA: Restrict Report Pairs: 1 = 1 report pair; 2 = 2 report pairs Unlimited Reports Enable: 0 = restrict reports to the setting in entry = unlimited reports for zones listed in zone list 7; (use zone list 7 to enter those zones that require unlimited reporting; these zones ignore the setting in entry 1)
168 Pager 3 Report Options

0,0,0]

Part. 1 Part. 2 common See field *162 for reporting options. Select for each partition (use zone list 11 if using options 12 or 13).
DOWNLOAD INFORMATION (94, 95) 94 Download Phone No.
Enter up to 20 digits, 09; #+11 for ''; #+12 for '#'; #+13 for a 2second pause. Do not fill unused spaces. If fewer than 20 digits, exit field by pressing. To clear entries from field, press 94. UL: downloading may be performed only if a technician is at the site.

169 Pager 4 Phone No.

170 Pager 4 Characters
95 Ring Count For Downloading
NOTE: Do not enter 0 if using 4285/4286 Phone Module. 0 = Disable Station Initiated Download; 114 = number of rings (19, # +10 =10, # +11 =11, # +12 =12, # +13 =13, # +14 =14); 15 = answering machine defeat (# +15 =15).

197 Exit Time Display Interval
184 Configurable Zone Type 91
0 = no display; 1-5 = seconds between display refresh NOTE: If enabled and using only 2-digit fixed-word keypads (e.g., 6150RF), do not set exit delay time greater than 96 seconds. See Inst. Instr. for explanation.
198 Display Partition Number 199 ECP Fail Display
0 = 3-digit display (1 + device address) 1 = 2-digit fixed-display as 91
(VISTA-20P; for Alpha Display Keypads) 0 = no; 1 = yes (partition no. appears on Alpha Display)
185 Zone Type 91 Report Codes
91 ALARM ID: XXX TROUBLE ID: XXX
189 AUI Device 1 and 2 Enable
(for Touch Screen Style Keypads)

[1] [1]

AUI 1 AUI 2 System supports up to two touch screen style keypads (e.g., Symphony Advanced User Interface, and 6270 Touch Screen Keypad). AUI Compatibility Note: To ensure proper AUI device operation, connect only to controls having microprocessor version 3.0 or higher, and use AUI devices with the following rev levels: 6270 series use version 1.0.9 or higher; 8132/8142 (Symphony) series use version 1.1.175 or higher. Touch Screen (AUI) device 1: Must set AUI device address to 1 Touch Screen (AUI) device 2: Must set AUI device address to 2 VISTA-20P: Enter each touch screen keypads home partition 0 = disable; 1 = partition 1; 2 = partition 2; 3 = partition 3 (common) VISTA-15P: 0 = disable; 1 = enable NOTE: Use of touch screen style keypads does not affect the number of standard keypads supported.
Configurable Zone Types Worksheets
Configurable zone types 90 and 91 can be programmed via downloader software or from a keypad using data fields*182*185. Configurable zone types 92 and 93 (VISTA-20P only) can only be programmed using the downloader software. Programming Configurable Zone Type options involves making 10 entries in data field *182 for zone type 90 and field *184 for zone type 91, where each entry represents the sum of the values of the various options shown in the tables below. Use fields *183 and *185 to program Contact ID report codes for these zone types. ENTRY 1

Power Reset/ Use Entry Verification Delay 1/= no 0 = show alarms 0 = no 1 = delay 1 when armed 4 = power reset 2 = delay 2 & disarmed after fault (by code + OFF) 1 = dont show alarms when 12 = verification (see zone armed (show type 16) alarms, trbles,

faults when disarmed)

3 = never show any alarms, trbles, faults Entry 7 = fault display + power reset/verification
Entry 8 = entry delay 1/entry delay 2 + exit delay + interior zone type

ENTRY 9

Alarm Sounds Use Bell Timeout 0 = no 4 = yes Respond as Fire Zone 0 = no 8 = yes

ENTRY 10

Trouble Sounds 0 = none 1 = periodic beep 2 = trouble beeps Chime when Chime Mode On 0 = no 4 = yes
0 = none 1 = steady keypad 2 = steady bell see fields *32, see zone type and keypad *33 09; see note = pulsing bell and keypad Entry 9 = alarm sounds + bell timeout + fire zone
Entry 10 = trouble sounds + chime
*56 Zone Programming Menu Mode
(press *56 while in Program mode)
The Zone Programming Worksheet is on page 13.
For each of the following prompts, make the desired entry, followed by the [] key to accept the entry. Refer to the Installation and Setup Guide for detailed explanations for each prompt. SET TO CONFIRM?
0 = no; 1 = yes (See XMIT TO CONFIRM prompt later in this section.) We recommend that you confirm the programming of every transmitter.

XMIT TO confirm

Appears if you answered Yes at the Set to Confirm prompt. Activate the loop input or button that corresponds to this zone. Press [] to continue. If the serial/loop number transmitted does not match the serial number entered, a display showing the entered and the received serial/loop numbers appears. If so, activate the loop input or button on the transmitter once again. If a match is not obtained, press the [#] key twice and then enter (or transmit) the correct serial number. Press [] to continue If the serial number transmitted matches the serial number entered, the keypad will beep 3 times and a summary display will appear, showing that zone's programming. An s indicates that a transmitters serial number has been enrolled. Press [] to accept the zone information and continue.

ENTER ZN NUM.

01-64, 91, 92, 95, 96, 99 To quit, enter 00 to quit (returns to data field mode).

SUMMARY SCREEN:

System displays a summary of the entered zones current programming. Press [] to continue.

(prompts continued in next column)
Wireless Key Programming Templates (press the [D] key from *58 Menu mode Summary Screen)
This procedure programs the wireless keys, but a key is not active for arming/disarming until it is assigned to a user number (see System Operation section, Assigning Attributes Command in the Installation Instructions). TEMPLATE ?
Enter desired template number 16 (see chart below), then press [] to continue. To exit the Template screen, press [#]. The system returns to the *58 Menu mode Summary Screen.

ENTER START ZONE

The system displays the lowest zone number of the highest available consecutive 4-zone group. To start at a different zone number, enter the zone desired, and press []. If the system has four consecutive zones beginning with that zone, the zone number is displayed. If not, the system will again display a suggested zone that can be used. If the required number of consecutive zones is not available at all, the system will display 00. Press [] to accept. Continue to the INPUT S/N (serial number/loop number) and XMIT TO CONFIRM prompts described earlier in the *56 Menu Mode section. IMPORTANT: When confirmed, the key is not active for arming/disarming until it is assigned to a user number (using the assigning attributes command, attribute 4). See System Operation section in Installation Instructions. When done, the keypad beeps three times and the display returns to the ENTER START ZONE prompt to let you enter the starting zone for the next wireless key.
TEMPLATE SUMMARY L T 21 23
The selected template is displayed. The top line represents loop numbers, the bottom line represents each loops zone type. Press [] to accept template and continue.

PARTITION (VISTA-20P)

Enter the partition (1, 2, or 3-common) in which the key is to be active. Press [] to continue.
Wireless Key Predefined Default Templates

For 5804

TEMPLATE 1

Function

No Response Disarm Arm Away No Response No Response Disarm Arm Away Arm Stay 24-hour audible Disarm Arm Away Arm Stay

Zone Type

For 5804BD

TEMPLATE 4

LOOP 3
No Response No Response Arm Away Disarm No Response Arm Stay Arm Away Disarm 24-hour audible Arm Stay Arm Away Disarm
LOOP 3 LOOP 2 LOOP 4 YOU MUST ENROLL THIS BUTTON LOOP 3 LOOP 1 SET HOUSE CODE

TEMPLATE 2

TEMPLATE 5

TEMPLATE 3

TEMPLATE 6
5800 Series Transmitter Input Loop Identification
All of the transmitters illustrated have one or more unique factory assigned input (loop) ID numbers. Each of the inputs requires its own programming zone (e.g., a 5804's four inputs require four programming zones). For information on any transmitter not shown, refer to the instructions accompanying that transmitter for details regarding loop numbers, etc.

Enter the partition (1-3) in which this function key will be active.

KEY "A" FUNC

Enter the desired function for this key: 00 = For the Function key selected, the function will be as follows (default): If A selected = Zone 95 (emergency key, same as [1] [] pair) If B selected = Zone 99 (emergency key, same as [] [#] pair) If C selected = Zone 96 (emergency key, same as [3] [#] pair) If D selected = Single-button paging (continued in next column)

79 Menu Mode

ENTER OUTPUT NO.

80 Menu Mode (continued)

Enter the device output number (programmed in *79 Menu Mode) you want associated with this output. 01-16 = VISTA-20P output no.; 01-08 = VISTA-15P output no.; 17-18 = onboard triggers Press [] to continue.
(press 79 while in Programming mode)
The *79 Device Mapping Worksheet is on page 14.
01-18 = VISTA-20P relays/X-10; 01-08, 17, 18 = VISTA-15P relays/X-10 [] to continue
OUT NORM LOW (appears only for triggers 17/18)
0 = no (standard default); sets the output level normally high 1 = yes; sets the output normally low (can be used for resetting 4-wire smoke detectors) [] to return to Output Number prompt

SUMMARY SCREEN

A summary screen appears showing the programmed settings. Press [] to return to OUTPUT FUNCTION NUMBER prompt.

OUTPUT TYPE

0 = delete; 1 = relay (skip to B prompt); 2 = Powerline Carrier device (skip to A prompt) [] to continue.

*81 Menu Mode

(press *81 while in Programming mode)
The Zone List Worksheet is on page 14.

ZONE LIST NO.

Enter the zone list number (01-12) to program (or 00 to exit this mode). Press [] to continue.
A (if X-10 was selected) UNIT No.
Enter the unit code (01-16, set at the device). [] to return to the Output Number prompt continue
Enter each zone number (01-64) to add to the zone list, followed by pressing [] (example, 01, 02, 03). Press 00 to continue. VISTA-20P = 01-64; VISTA-15P = 01-06, 09-34, 49-56. IMPORTANT: Do not include fire zones in zone lists that are used to STOP device actions.
B (if relay was selected) MODULE ADDR
Enter the predefined address for this module (07-15; see Table of Device Addresses on page 2). Make sure the modules DIP switches are set to the selected address. [] to continue

ALPHA VOCABULARY LIST (For Entering Zone Descriptors)
(Word Space) A AIR ALARM ALLEY AMBUSH AREA APARTMENT ATTIC AUDIO B BABY BACK BAR BASEMENT BATHROOM BED BEDROOM BELL BLOWER BOILER BOTTOM BREAK BUILDING C CABINET CALL CAMERA CAR CASH CCTV CEILING CELLAR CENTRAL CIRCUIT CLOSED COMPUTER CONTACT D DAUGHTERS DELAYED DEN DESK DETECTOR DINING DISCRIMINATOR DISPLAY

062 064

084 085

102 103

DOOR DOWN DOWNSTAIRS DRAWER DRIVEWAY DUCT E EAST ELECTRIC EMERGENCY ENTRY EQUIPMENT EXIT EXTERIOR F FACTORY FAMILY FATHERS FENCE FIRE FLOOR FLOW FOIL FOYER FREEZER FRONT G GARAGE GAS GATE GLASS GUEST GUN H HALL HEAT HOLDUP HOUSE INFRARED INSIDE INTERIOR INTRUSION J JEWELRY K KITCHEN

117 118

152 153
L LAUNDRY LEFT LEVEL LIBRARY LIGHT LINE LIVING LOADING LOCK LOOP LOW LOWER M MACHINE MAIDS MAIN MASTER MEDICAL MEDICINE MONEY MONITOR MOTHERS MOTION MOTOR N NORTH NURSERY O OFFICE OPEN OPENING OUTSIDE OVERHEAD P PAINTING PANIC PASSIVE PATIO PERIMETER PHONE POINT POLICE POOL POWER

202 207 208

R RADIO REAR RECREATION REFRIGERATION RF RIGHT ROOM ROOF S SAFE SCREEN SENSOR SERVICE SHED SHOCK SHOP SHORT SIDE SKYLIGHT SLIDING SMOKE SONS SOUTH SPRINKLER STATION STORE STORAGE STORY SUPERVISED SUPERVISION SWIMMING SWITCH T TAMPER TELCO TELEPHONE TEMPERATURE THERMOSTAT TOOL TRANSMITTER U UP UPPER UPSTAIRS UTILITY

253 254

V VALVE VAULT VOLTAGE W WALL WAREHOUSE WEST WINDOW WING WIRELESS X XMITTER Y YARD Z ZONE (No.) ZONE 1ST 2 2ND 3 3RD 4 4TH 5 5TH 6 6TH 7 7TH 8 8TH 9 9TH Custom Word #1 Custom Word #2 Custom Word #3 Custom Word #4 Custom Word #5 Custom Word #6 Custom Word #7 Custom Word #8 Custom Word #9 Custom Word #10
Bulleted () words in boldface type are those that are also available for use by the 4285/4286 Phone Module. If using a Phone module, and words other than these are selected for Alpha descriptors, the module will not provide annunciation of those words. Italicized words followed by an asterisk indicate those words supported by the 6160V/6150V Voice Keypads
CHARACTER (ASCII) CHART (For Adding Custom Words)
32 (space) 33 ! 34 " 35 # 36 $ 37 % 38 & 39 ' 40 ( 49 ) * + , . / 9 : 67 ; < = > ? @ A B C 76 D E F G H I J K L 85 M N O P Q R S T U 90 V W X Y Z

Setting Schedules (Installer Code + [#] + [6] [4])

ENTER SCHED NO.

VISTA-20P: 01-16 = end-user schedules; 17-32 = installer-only schedules VISTA-15P: 01-04 = end-user schedules; 05-08- = installer-only schedules [] to continue. To Quit, enter 00.
GROUP NUMBER ( for event 2 user access)

1-8; [] to continue.

PARTITION ( for events 3-7,10,12)
0 = all partitions; 1 = partition 1; 2 = partition 2; 3 = common [] to continue.

ENTER EVENT

00 = clear event 01 = Relay On/Off 02 = User Access 03 = Latch Key Report to Pager (sent to all pagers in the users partition; message sent is 777-7777. User must be enabled for paging and system must be armed before reporting can occur.) 04 = Forced Stay Arming (Forced bypass is automatically enabled regardless of setting in field *23) 05 = Forced Away Arming (Forced bypass is automatically enabled regardless of setting in field *23) 06 = Auto Disarm 07 = Display Reminder 10 = Display custom words (if selected, system displays custom words 8, 9, and 10 at defined time. Can be used as installers reminder message to the end user); programmable by installer only 11 = Periodic Test Report (see key commands in Test Report Code, data field *64, to quickly set periodic test reporting intervals); programmable by installer only [] to continue.
01-12 = hour; 00-59 = minute; 0 = AM; 1 = PM; to select days, position the cursor under the desired days using the [] key to move forward, then press 1 to select the day. [] to continue.
STOP (for events 1 relay on/off; 2 user access; 3 latch key report)
See START for entries. [] to continue.

REPEAT

0 = do not repeat; 1 = repeat schedule weekly; 2 = repeat schedule biweekly (every other week); 3 = repeat schedule every third week; 4 = repeat schedule every fourth week [] to continue
RANDOMIZE (for events 01 and 11)
0 = no; 1 = yes If selected, the scheduled start and stop times will vary within 60 minutes of the hour time. For example, if a schedule is set to start at 6:15pm, it will do so the first time 6:15pm arrives, but on subsequent days it will start anytime between 6:00 and 6:59 p.m. NOTE: Do not use the random option if the start and stop times are within the same hour setting, otherwise unpredictable results may occur (e.g., the randomized stop time may occur before the start time). [] to continue and return to ENTER SCHED NO. prompt to program the next schedule.

DEVICE NUMBER ( for event 1 relay on/off)

01-18; [] to continue.

SCHEDULES WORKSHEET(installer code + [#] + [6] [4]; master code can only access schedules 01-16 for VISTA-20P, 01-04 for
VISTA-15P, and events 00-07 for both controls; VISTA-15P supports up to 8 schedules, VISTA-20P supports up to 32 schedules )

(see list below)

Device No.
for 01 events: enter 01-18

Group No.

for 02 events: enter 1-8

Partition

for 04-06 events: enter 1, 2, or 3 (VISTA-20P)

Start Time/ Days

Stop Time/ Days

Repeat

Random

(yes/no)

Events: Master/Installer Installer Only 00 = clear event 04 = forced STAY arm 10 = display custom words 8-= device on/off 05 = forced AWAY arm 11 = periodic test report 02 = user access 06 = auto disarm 03 = latch key report 07 = display reminder Repeat Options: 0 = none; 1 = repeat weekly; 2 = repeat every other week; 3 = repeat every third week; 4 = repeat every fourth week
*56 ZONE PROGRAMMING WORKSHEET (VISTA-15P supports up to 32 zones: 1-6, 9-34, 49-56) [default shown in brackets]
Zone Zn Type Part. Report Hardwire Type Rsp. Time Location
[09] [01] [03] [03] [03] [03] [03] [03]

Zn Type

[1] [1] [1] [1] [1] [1] [1] [1]

Part. Report

[EOL] [EOL] [EOL] [EOL] [EOL] [EOL] [EOL] [EOL]

Input Type Loop

Serial No. Location

NOTES:

Zone Type: see chart on page 12; Report Code: enabled if any digit entered as 1st digit; Hardwire Type (zns 1-8): 0 = EOL 3 = ZD 1 = NC 4 = DB 2 = NO Input Type: 2 = AW (zones 9-48) 3 = RF (zones 9-48) 4 = UR (zones 9-48) 5 = BR (zones 49-64) NOTE: Zones 9-16 not available if zone doubling enabled. Response Time: 0 = 10msec 1 = 350msec 2 = 700msec 3 = 1.2 sec
Reserved Zones 91 = addressable device
report enable/disable default zone type = [05].

92 = Duress report

enable/disable
[1] [1] [1] [1] [1] [1] [1] [1] [1] [1] [1] [1] [1] [1] [1] [1] [00] [00] [06]
[BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] N/A N/A N/A

N/A N/A N/A N/A N/A N/A

keypad [1] / [] keypad [3] / [#] keypad [] / [#]
*57 FUNCTION KEY WORKSHEET

A Option

com P1 P2 com P1

P2 com P1

P2 com

Comments

Paging Time Display Arm AWAY Arm STAY Arm NIGHT-STAY Step Arming Device Activation Device: Comm. Test Macro Key 1 Assign each macro key to only a single partition. Macro Key 2 Assign each macro key to only a single partition. Macro Key 3 Assign each macro key to only a single partition. Macro Key 4 Assign each macro key to only a single partition. Emergency Keys: zone 95 zone 99 zone 96 paging Personal Emergency n/a Silent Alarm n/a Audible Alarm n/a Fire n/a Emergency Keys: A = paired keys [1] / [] (zone 95); B = paired keys [] / [#] (zone 99); C = paired keys [3] / [#] (zone 96) There are only four macros system-wide.

OUTPUT RELAYS/POWERLINE CARRIER (X-10) DEVICES WORKSHEET FOR 79, 80 and 81.
Applicable only if Relays and/or Powerline Carrier Devices are to be used. 79 RELAY/POWERLINE CARRIER (X-10) DEVICE MAPPING (Must program before using *80)
OUTPUT TYPE Relay X10 Output Module Pos Unit Description No. Addr. (1-4) No. OUTPUT TYPE (09-16 apply to VISTA-20P only) Relay X10 Output Module Pos Unit Description No. Addr. (1-4) No. On-Board Trigger 1 norm output = 17 On-Board Trigger 2 norm output = 18

ZONE LISTS WORKSHEET

Fill in the required data on the worksheet below and follow the procedure in the installation manual as you enter the data during the displays and prompts that appear in sequence. NOTE: Record desired zone numbers below, noting that a list may include any or all of system's zone numbers.

List No.

Used For General Purpose (GP) General Purpose Chime-by-Zone or GP Cross Zones or GP Night-Stay Zones or GP Dial Delay Disable or GP Unlimited Reports or GP General Purpose Zones activating pager 1 Zones activating pager 2 Zones activating pager 3 Zones activating pager 4

Contains These Zones

(see field *26 for Chime-by-Zone option) (see field *85 for Cross Zone Timer option) V20PSIA/V15PSIA: see field *50 for Dial Delay Disable option V20PSIA/V15PSIA: see field *93 for Unlimited Reports option

(VISTA-20P) (VISTA-20P)

80 OUTPUT DEFINITIONS
Fill in the required data on the worksheet below and follow the programming procedure in the installation manual as you enter the data during the displays and prompts that appear in sequence. Notes: 1. For Relays, 4229 and 4204 devices are programmed in *79, *80, and *81 modes. 2. For Powerline Carrier devices (plcd), field 27 must be programmed with a House Code. 3. Tampers of expansion units cannot be used to operate devices.
Output Function Number (V20P=1-48) (V15P=1-24) Activation Type and Detail Partition Number Activated by Zone List Zone Type Zone No. (P) (ZN) 0=delete (ZL) (ZT) (if using ZT trig) 1=zn list 1-8 = list (see table 00=none 2=zn type below) V20P: 01-= any 1 = partition 1 3=zn no. V15P: 01-06, 2 = partition 2 09-34, 49-= common Event (for zone list/activated by) Output Device Action Number Type 0 = off By Zone List By Zone No. 1 = close 2 secs 2 = stay closed V20P=1-18 R = relay 0 = restore 0 = restore T = trigger 3 = pulse 1 = alarm 1 = alrm/flt/trbl V15P=1-8, X = X= toggle 2 = fault 17, = duration = trouble 6 = duration 2
ZONE TYPE/SYSTEM OPERATION Choices for Zone Types are: 00 = Not Used 05 = Trouble Day/Alarm Night 10 = Interior w/Delay 24 = Silent Burglary 01 = Entry/Exit#= 24 Hr Silent 12 = Monitor Zone 77 = Keyswitch 02 = Entry/Exit#= 24 Hr Audible 14 = Carbon Monoxide 81 = AAV Monitor Zone 03 = Perimeter 08 = 24 Hr Aux 16 = Fire w/Verification 90-91 = Configurable 04 = Interior Follower 09 = Fire 23 = No Alarm Response Choices for System Operation are: Note: In normal operation mode: 20 = ArmingStay 38 = Chime 52 = Kissoff Code + # + 7 + NN Key Entry starts Device 21 = ArmingAway 39 = Any Fire Alarm 54 = Fire Zone Reset Code + # + 8 + NN Key Entry stops Device 22 = Disarming (Code + OFF) 40 = Bypassing 58 = Duress 31 = End of Exit Time 41 = **AC Power Failure 60 = AAV Trigger ** Use 0 (any) for Partition No. (P) entry. 32 = Start of Entry Time 42 = **System Battery Low 66 = Function key *** Or at Disarming, whichever occurs earlier. 33 = Any Burglary Alarm 43 = Communication Failure 67 = Bell Failure Use *57 Menu mode to assign the function key. 36 = **At Bell Timeout*** 68 = TELCO Line Fault Duration is set in program field *177. 78 = Keyswitch red LED Device action not used for these choices. 79 = Keyswitch green LED

4-WIRE SMOKE DETECTOR CONNECTIONS

OUTPUT 17 (TRIG. 1)

+12 AUX GND OUTPUT 18 (TRIG. 2)
SEALED LEAD-ACID TYPE. BATTERY NORMALLY NEED NOT BE REPLACED FOR AT LEAST 3 YRS. TO DETERMINE TOTAL STANDBY LOAD ON BATTERY, ADD 100mA TO TOTAL OF AUX. POWER OUTPUT AND REMOTE KEYPAD CURRENTS. USE UL LISTED LIMITED ENERGY CABLE FOR ALL CONNECTIONS RED JUMPER CUT FOR BELL SUPERVISION. ALSO, CONNECT 2000 OHM RESISTOR DIRECTLY ACROSS SOUNDER.
5881L: UP TO 8 5881M: UP TO 16 5881H: UP TO 56 *5882 IN CANADA
OPTIONAL FOR UP TO 40 ADDITIONAL ZONES ( FROM EITHER OR BOTH GROUPS)
USE 1361X10 TRANSFORMER INTERFACE IN PLACE OF 1321 OR 1321CN WHEN POWER LINE CARRIER DEVICES ARE BEING USED. (SEE INSTRUCTIONS FOR CONNECTIONS)

ZONE 7

ZONE 1

ZONE 8

ZONE 2

ZONE 3

ZONE 4

ZONE 5

BLACK: KEYPAD GROUND (- ) RETURN
ALL OUTPUTS ARE POWER LIMITED. 2000 OHMS EOLR

ZONE 6

VISTA-20P ONLY
GREEN: DATA IN FROM KEYPAD

RED: KEYPAD PWR ( + )

YELLOW: KEYPAD DATA OUT
165 Eileen Way, Syosset, NY 11791 Copyright 2003 Honeywell International Inc.
THIS EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION'S STANDARD 72, CHAPTER 2 (NATIONAL FIRE PROTECTION ASSOCIATION, BATTERY-MARCH PARK, QUINCY,MA 02269). PRINTED INFORMATION DESCRIBING PROPER INSTALLATION, OPERATION,TESTING, MAINTENANCE, EVACUATION PLANNING AND REPAIR SERVICE IS TO BE PROVIDED WITH THIS EQUIPMENT.
CAN BE USED FOR 2-WIRE SMOKE DETECTORS
24-HR BATTERY STANDBY REQUIRED FOR FIRE INSTALLATIONS. USE 12V, 17.2AH BATTERY FOR 600mA AUX POWER. SEE INSTRUCTIONS.
BATTERY FUSE 3A FOR REPLACEMENT, USE SAME VALUE (e.g. ADEMCO No. 90-12)
RELAY PROGRAM RELAY AS ZONE TYPE 54 (FIRE ZONE RESET) _ 4
BATTERY CAPACITY FOR EMERGENCY BURGLARY STANDBY USE AT LEAST 4 HRS
8-PIN CONNECTOR USED FOR 1361X10 TRANSFORMER CONNECTIONS AND FOR ON-BOARD TRIGGERS SEE INSTRUCTIONS. 7 8

BLK RED GRN YEL AND/OR

ADEMCO 5881* Type RF RECEIVER WIRELESS ZONES
AUX PWR SET UNITS OUTPUT DIP SWITCH TERMINALS FOR DEVICE ADDRESSES 7 - 15 SEE OR INSTRUCTIONS.

BATTERY 12V, 4AH RED

CHARGING VOLTAGE 13.8VDC. MAXIMUM CHARGING CURRENT 650mA.
TO TERM 4 TO TERM 5 TO TERM 6 TO TERM 7
BLK RED GRN YEL BLK RED GRN YEL
ADEMCO No. 4219 WIRED EXPANSION MODULE (8 ADD'L EOLR WIRED ZONES) -AND/ORADEMCO No. 4229 WIRED EXPANSION/RELAY MODULE (8 ADD'L EOLR WIRED ZONES PLUS 2 OUTPUT RELAYS) -AND/ORADEMCO No. 4204 RELAY MODULE (4 OUTPUT RELAYS)

NOTE: KEYPAD (S) CURRENT (IN BOTH PARTITIONS) AND ALL OTHER DEVICES DRAWING POWER FROM TERMS 4 & 5 MUST BE INCLUDED IN AUX CURRENT DRAIN CALCULATIONS.

2 / / / / / / / 16

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM. IN ADDITION, THIS SYSTEM MUST BE CHECKED BY A QUALIFIED TECHNICIAN AT LEAST ONCE EVERY THREE (3) YEARS.

2k ZONE 3

2k ZONE 4
TYPICAL WIRING FOR DOUBLE BALANCED ZONE (VISTA-20P ONLY)
TYPICAL WIRING FOR ZONE DOUBLING (VISTA-20P ONLY)
REMOTE KEYPADS CAN USE 6150 OR 6160 KEYPADS. LOCAL PROGRAMMING MUST BE DONE WITH A 6139/6160, BUT NEED NOT REMAIN IN THE SYSTEM (SET TO ADDRESS 16).
ALL DEVICES AND ACCESSORIES USED IN A CANADIAN INSTALLATION MUST BE LISTED FOR USE IN CANADA
ADEMCO VISTA-20P / VISTA-20PSIA SERIES / VISTA-15P / VISTA-15PSIA SERIES SUMMARY OF CONNECTIONS

V20P_V15P-SOC-V5

Mounting and Wiring the Control
This section describes the procedures for mounting and wiring this control and its peripheral devices. In the following subsections, procedures are listed in the left column, while notes and pertinent explanations are provided in the right column.

Cabinet and Lock

1. Mount the control cabinet to a sturdy wall in a clean, dry area, which is not readily accessible to the general public, using fasteners or anchors (not supplied) with the four cabinet mounting holes. Remove cabinet door, then remove the lock knockout from the door. Insert the key into the lock. Position the lock in the hole, making certain that the latch will make contact with the latch bracket when the door is closed. When correctly positioned, push the lock until it is held securely by its snap tabs.
The cabinet can be closed and secured without a lock by using 2 screws in the cover's edge.

CHECK POSITION

LOCKED

ADEMCO

SNAP TAB
PUSH ON LOCK UNTIL IT IS SEATED SECURELY

UNLOCKED

CABINET DOOR BOTTOM

STEP 1

STEP 2
Figure 1. Installing the Cabinet Lock
Mounting the PC Board Alone
(no RF Receiver) 1. Hang two short mounting clips (provided) on the raised cabinet tabs (see Detail B in Fig. 2). 2. a. Insert the top of the circuit board into the slots at the top of the cabinet. Make sure that the board rests on the correct row (see Detail A). b. Swing the base of the board into the mounting clips and secure the board to the cabinet with the accompanying screws (see Detail B).
Before installing the cabinet's contents, remove the metal cabinet knockouts required for wiring entry. Do not remove the knockouts after the circuit board has been installed.

CIRCUIT BOARD

CABINET
DETAIL A SIDE VIEW OF BOARD SUPPORTING SLOTS
DETAIL B SIDE VIEW OF MOUNTING CLIPS

MOUNTING-001-V0

Figure 2. Mounting the PC Board

cab_lock_snap-001-V0

Installation Instructions
Mounting Board with RF Receiver
1. a. Remove the receiver board from its case, then insert the top of the board into the slots at the top of the cabinet, as shown in Detail A in Figure 3. Make sure that the board rests on the correct row of tabs. b. Swing the base of the board into the mounting clips and secure it to the cabinet with the accompanying screws. c. Insert the top of the control's board into the slot in the clips and position two clips at the lower edge of the board. d. Swing this board into place and secure it with two additional screws. Insert grounding lugs (supplied with the receiver) through the top of the cabinet into the left-hand terminals of the antenna blocks (at the upper edge of the receiver board) and secure them to the cabinet top with the screws provided, as shown in Detail B. Insert the receiver's antennas through the top of the cabinet, into the blocks' right-hand terminals, and tighten the screws.

5804BD, 5827, 5827BD) do not send check-in signals.
The following transmitters are not intended for use in UL installations: 5802MN, 5802MN2, 5804, 5804BD, 5814, 5816TEMP, 5819, 5819WHS & BRS, and 5850. The 5827BD and 5800TM can be used in UL Listed Residential Burglar installations.
Transmitter Battery Life See Wireless Transmitter paragraph in the Limitations of This Alarm System statement located at the end of this manual for information on transmitter battery life. Some transmitters (e.g., 5802 and 5802CP) contain long-life but non-replaceable batteries, and no battery installation is required. At the end of their life, the complete unit must be replaced (and a new serial number enrolled by the control). Button-type transmitters (such as 5801, 5802, and 5802CP) should be periodically tested for battery life. The 5802MN and 5804 Button Transmitters have replaceable batteries. Do not install batteries in wireless transmitters until you are ready to enroll during system programming. After enrolling, batteries need not be removed.

Installing a Keyswitch

1. Connect the 4146 keyswitch's normally open momentary switch to a zones terminals. Remove the 2000 ohm EOL resistor if connected across the selected zone. 2. Using a standard keypad cable as shown: Connect the yellow and white keyswitch wires to trigger connector pin 3 (+12V). Connect the Red and Green LED wires to the appropriate output 17/output 18 trigger connector pins. 3. Connect a 2000 ohm EOL resistor across the momentary switch. 4. You can wire an optional closed-circuit tamper switch (model 112) in series with the zone. If the switchplate is then removed from the wall, the tamper will open, disabling keyswitch operation until the system is next disarmed from the keypad. If the tamper is opened when the system is armed, an alarm will occur.
Use only one keyswitch per partition. When using a keyswitch, the zone it is connected to is no longer available for use as a protective zone. Use *56 Menu mode to program the keyswitch zone and assign it zone type 77. Use *80 Menu mode to program the LED functions: program outputs 17 and 18 for system operation zone type 78 (red LED) and 79 (green LED) as appropriate (see Output Device Programming section).

OUTPUT 17 (YELLOW)

Go to a Data Field

Entering Data
Review a Data Field Deleting an Entry
Interactive Mode Programming (56, *57, 58, 79, 80, 81, 82)
Entering Interactive Mode Press [] + [Interactive Mode No.] (for example, 56) while in Program Mode. The Alpha display keypad will display the first of a series of prompts requesting entries. After making the appropriate entry, press the [] key to accept the entry and continue to the next prompt.
Loading Factory Defaults/Initializing for Download
To Load Default Entries Press 97 while in Program Mode. This resets all data fields to the default values shown on the Program Form. Use 97 only if you wish to return to the original factory-programmed defaults. Press 96 while in Program Mode. This initializes the system for downloading and resets all the subscriber account numbers and CSID.
To Initialize Download ID
Do not press 97 to load defaults if any programming has been done previouslydata already programmed into the system will be changed! Exiting the Programming Mode
Prevent installer code reentry Press 98. Exits Programming Mode and prevents re-entry by: Installer Code + [8] + [0] + [0]. To enter the programming mode if 98 was used to exit, you must first power the system down. Then power up again, and press [] and [#] at the same time, within 50 seconds of powering up. See field *88 for other Program mode lockout options. Press 99. Exits Programming Mode and allows re-entry by: Installer Code + [ 8] + [0] + [0] or by: Pressing [] and [#] at the same time, within 50 seconds of power-up.
Reports as n/a n/a n/a n/a n/a n/a n/a n/a n/a Enabled By *56 zone programming: input device type entry automatic if output to long range radio field *29 enabled automatic if phone module access code field *28 enabled *56 zone programming: input device type entry, then: automatic if zone no. 9-16 entered as AW type or relay assigned automatic if zone no. 17-24 entered as AW type or relay assigned automatic if zone no. 25-32 entered as AW type or relay assigned automatic if zone no. 33-40 entered as AW type or relay assigned automatic if zone no. 41-48 entered as AW type or relay assigned *79 output device programming: device address prompt: entered at device address prompt entered at device address prompt entered at device address prompt entered at device address prompt data field programming as listed below: always enabled for partition 1, all sounds enabled. data field *190 data field *191 data field *192 data field *193 data field *194 data field *195 data field *196 automatic

Secondary Phone No.

Part. 1 Primary Subs. Acct. No.
Part. 1 Secondary Subs. Acct. No. Part. 2 Primary Subs. Acct. No.
To clear entries from field, press 44.
VISTA-20P. To clear entries from field, press 45. VISTA-20P. To clear entries from field, press 46. Select the type of telephone service.
Part. 2 Secondary Subs. Acct. No. Phone System Select
If Central Station Receiver is not on WATS line: 0 = Pulse Dial; 1 = Tone Dial If Central Station Receiver is on WATS line: 2 = Pulse Dial; 3 = Tone Dial
Report Format (Primary/Secondary)
0 = 3+1, 4+1 ADEMCO L/S STANDARD 1 = 3+1, 4+1 RADIONICS STANDARD 2 = 4+2 ADEMCO L/S STANDARD 3 = 4+2 RADIONICS STANDARD 6 = 4+2 ADEMCO EXPRESS 7 = ADEMCO CONTACT ID REPORTING 8 = 3+1, 4+1 ADEMCO L/S EXPANDED 9 = 3+1, 4+1 RADIONICS EXPANDED
Select report format for primary and secondary phone numbers.

Split/Dual Reporting

0 = standard/backup reporting only (all reports only to primary unless unsuccessful, then will attempt secondary) 1 - 5 (see table to right)

1= 2= 3= 4= 5=

To Primary No. alarms, restore, cancel all except open/close, test alarms, restore, cancel all except open/close, test all
To Secondary No. others open/close, test all all all

Burglary Dialer Delay

0 = no dial delay 1 = 15 seconds 2 = 30 seconds 3 = 45 seconds
Provides delay of BURGLARY ALARM report to the central station, which allows time for the subscriber to avoid a false alarm transmission. This delay does not apply to zone type 24 alarms (silent burglary) or to 24-hour zone types 6, 7, and 8 (silent panic, audible alarm, auxiliary alarm), which are always sent as soon as they occur. UL: must be 0 SIA Installations: delay must be minimum of 30 seconds Select SESCOA or Radionics format. Select 0 for all other formats.

SESCOA/Radionics Select

0 = Radionics (0-9, B-F reporting) 1 = SESCOA (0-9 only reporting)
Installation Instructions FIELD TITLE and DATA ENTRIES Dynamic Signaling Delay
0 = disabled (both signals sent) 115 = entry times a 15-second delay. e.g., 1 = 15 seconds, 2 = 30 seconds, etc.
Intended for use with Long Range Radio reporting. This field lets you select the time the panel should wait for acknowledgment from the first reporting destination (see 55) before it attempts to send a message to the second destination. Delays can be selected from 0 to 225 seconds, in 15-second increments. This delay is per message. If 0 is entered in this field, the control panel will send redundant reports to both Primary Dialer and LRR. UL Installations: For Fire Alarm and UL Burglar Alarm installations without Line Security (Grade A), the maximum Dynamic Signaling Delay must be no more than 15 seconds. For UL Burglar Alarm installations with Line Security (Grade AA), Dynamic Signaling Delay must be 0. The reports will be sent to both the dialer and the LRR. Intended for use with Long Range Radio reporting. You must also enable field 29, OUTPUT TO LONG RANGE RADIO. Select the initial reporting destination for messages as follows: Primary Dialer First selected (0): If acknowledged before delay expires (see 54), then message will not be sent to LRR. If not acknowledged before delay expires, then message is sent to both the Primary Phone No. and LRR. Long Range Radio First selected (1): If acknowledged before delay expires, then message will not be sent to the primary dialer. If not acknowledged before delay expires, then message is sent to both the Primary Phone No. and LRR. Use this menu mode to program zone information. See Zone Programming section for procedures. This menu mode can be used to quickly program zone information, but is recommended only for those already familiar with *56 menu mode. See Zone Programming section for procedures. Use this menu mode to program keypad function keys. See Function Key section for procedures.

Device Duration 1, 2

0 = 15 secs 1 = 30 secs 2 = 45 secs 3 = 60 secs 4 = 90 secs 5 = 2 min 0 = 60 Hz 1 = 50 Hz
6 = 2-1/2 min 7 = 3 min 8 = 4 min 9 = 5 min #+10 = 6 min #+11 = 7 min

50/60 Hz AC Operation

Select the type of AC power applied to the control.
Configurable Zone Type Programming Fields
The system allows you to define custom zone types (VISTA-20P supports 4 [types 90-93]; VISTA-15P supports 2 [types 90, 91]), based on the options described below. All configurable zone types can be programmed via the downloader. Configurable zone types 90 and 91 can also be programmed from a keypad using data fields *182-*185 described below. UL installations: Do not configure zones as fire alarm or UL burglar alarm zones.
Configurable Zone Type 90
0-15 = values for each of 10 entries (0-9, # + 10 = 10, # + 11 = 11, # + 12 = 12, # + 13 = 13, # + 14 = 14, # + 15 = 15)
Enter the appropriate value for each entry, 1-10, based on the charts on the next page. To calculate the value for each entry, add the values of the selected options in each of the entrys columns shown in the respective chart (one option per column). For example, to program entry 2 for alarm response to short, auto restore on, but not a vent zone, enter 5 (1 for alarm short + 4 for auto restoreyes + 0 for vent zone-no). Enter the desired 3-digit Contact IDreport codes for alarms and troubles occurring on zones assigned to this zone type. Press [] to accept and continue. Important Notice on Report Codes: To avoid confusion at the central station, it is recommended that existing Contact IDcodes be used with configurable zone types whenever possible. See list in System Communication section and/or check with the central station for a complete list of Contact IDreport codes. If none of the codes are suitable, choose a code in the reserved range of 750-789 (reserved for configurable zone type report codes) and make sure to define the code with your central station. See field *182 for explanation of entries. See field *183 for explanation of entries and read the Important notice on using these codes.
Zone Type 90 Report Codes
%0%61 -( <<< 8639&0) -( <<<
Use existing Contact ID codes, if appropriate, or define unique codes in CID code range 750-789.

*184 *185

Configurable Zone Type 91

see *182 for entries

Zone Type 91 Report Codes
Configurable Zone Type Options
Auto Restore (entry 2) Vent Zone (entry 2) Faults on zones set for this option are cleared; restore messages sent upon restoral of faults. Zones set for this option are ignored if faulted when arming the system, but are protected if the zone is later restored (e.g., an open window can be ignored when arming, but if the window is later closed, it will be protected; opening the window again causes an alarm.) Zones set for this option can be bypassed only while the system is disarmed. Zones set for this option can be bypassed when the system is armed or disarmed. Alarms on zones set for this option participate in dial delay central station reporting, if system dial delay enabled in field *50. Faults on zones set for this option are delayed by the time set in field *87. Do not use this option if using entry/exit delay for this zone type. Selects how faults on zones set for this zone type are displayed. Selects whether the system resets power (when user enters code + OFF), and whether the system performs alarm verification (see description for zone type 16 in Programming Overview section) when a fault occurs on these zones. Selects whether to use the systems entry delay times. Selects whether to use the systems exit delay time. Zones set for this option are treated same as standard zone type 4 (bypasses when armed STAY, faults displayed). Selects the type of alarms sound for zones set for this zone type. Alarm sounding on zones set for this option remain for the duration set in fields *32 / *33. Zones set for this option respond in the same manner as if programmed for zone type 9. Do not set fire zones to respond as a fault in entries 1-6. Selects the type of trouble sounds for zones set for this zone type (periodic beeps = once every 30 seconds; trouble beeps = rapid beeping). Zones set for this option cause a chime when Chime mode is on.

Report Code (RC)

First Digit: 1-9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F 00 to disable Second Digit: same as above [] to continue

02 HARDWIRE TYPE EOL 0

Hardwire Type
0 = EOL 3 = zone doubling 1 = NC 4 = double-balanced 2 = NO [] to continue
This prompt appears only for zone numbers 02-08. Zone 1 is automatically set for EOL operation. VISTA-20P This prompt appears only for hard-wired zones 01-08 (zone 02 is used as an example in display). Option 3: used for clean me option on zone 1 (see field 174).

02 Response Time 1

Response Time (RT)
0 = 10mSec 1 = 350mSec 2 = 700mSec 3 = 1.2 seconds [] to continue

10 INPUT TYPE RF TRANS 3

Input Device type (In)
2 = AW (Aux wired zone) 3 = RF (supervised RF transmitter, 4 = UR (unsupervised RF transmitter) 5 = Button type RF transmitter (unsupervised). [] to continue
This prompt is skipped for zones 1-8, or 1-16 if zone-doubling was enabled at Hardwire Type prompt. All of the RF transmitters have one or more unique factory-assigned input (loop) ID codes. Each of the inputs requires its own programming zone (e.g., a 5804's four inputs require four programming zones). RF Transmitters can be enrolled as one of the following types: Type Description RF Sends periodic check-in signals, as well as (Supervised RF) fault, restore, and low-battery signals. The transmitter must stay within receiver's range. UR Sends all the signals that the RF type (Unsupervised RF) does, but the control does not supervise the check-in signals. The transmitter may therefore be carried off-premises. BR (Unsupervised Sends only fault signals. It will not send a Button RF) low-battery signal until it is activated. The transmitter may be carried off-premises. NOTE: For the built-in hardwired zones, the Input Device type is automatically displayed as HW and cannot be edited. To change the input type of a previously programmed wireless device (type RF, UR, BR) to a wired zone (type AW), you must first delete transmitters serial number (see To Delete A Serial Number prompt on next page)

PROMPT

10 INPUT S/N: L A022-4064 1
VALID ENTRIES Serial number Entry and Loop Number Entry
see explanation [] to continue
Used only when enrolling wireless transmitters. a. Transmit two open/close sequences. If using a button-type transmitter, press and release the button twice, but wait about 4 seconds before pressing the button the second time. OR b. Manually enter the 7-digit serial number printed on the label of the transmitter. Then press the [] key the cursor will move to the L position. You can edit the loop number, if necessary. When the loop number is acceptable, press []. c. Press key [C] to copy the serial number previously enrolled (used when programming a transmitter with several input loops). NOTE: If the [C] key is used to copy the previously enrolled serial number, the cursor will move to the Loop column (L) with the previous serial number displayed, and display a highlighted question mark for the loop number. Enter the loop number and press []. The system will now check for a duplicate serial/loop number combination.

Output No.

For example, if you want to pulse a strobe light upon fire alarms on zone 4 using a relay mapped to output number 2 (as programmed in *79 Menu Mode), program the following in *80 Menu Mode: Prompt Entry Output Funct. # = 01 (assuming this is the first output function) Activated By: Enter Zn No. Output Action = 3 (zone number) = 04 (requires 2-digit zone numbers) = 3 (continuous pulse)
Output Number = 02 (device mapped in *79 Menu Mode) Start Output Definition mode by pressing 80 while in Data Programming mode. The following prompts are displayed: 80 Menu Mode PROMPT
Output Funct. # (00 = Quit) A E P Trig ?0 ZL=1
VALID ENTRIES Output Function No.
Enter the output function number to be defined (or 00 to exit).
01-48 = output function number [] to continue
This screen displays a summary of the current output programming (for this example, Zone List has been selected-this is the default screen). A = Output Action; E = Triggering event; P = Partition; Trig = Trigger type NOTE: A question mark in the summary screen indicates that the device number shown has not been mapped. Use *79 Menu mode to map the device.
01 Activated By: Zone List

Activated By

0 = delete 1 = zone list 2 = zone type 3 = zone number [] to continue
Select where the initiating event for this output definition is to occur as follows: 0 = delete (deletes the output function and any previous programming;-see prompt below) 1 = zone list (go to A prompt) 2 = zone type (go to B prompt) 3 = zone number (go to C prompt) If you enter 0, the following prompt appears: Delete? 0 = NO, 1 = YES Press 1 to delete this output definition.

01 Zn List 1

Zone List
01-08 = zone list [] to continue
If zone list was selected, this screen appears. Otherwise skip to the next row. Enter the desired zone list number associated with this output number. NOTE: Do not use pager zone lists 09-12 in output definitions. Press [] to continue. Enter the zone list event that will activate this output. Enter Event Alarm = restore; 1 = alarm; 2 = fault; 3= trouble
NOTE: For alarm, fault, and trouble, an event on ANY zone in the list activates the output, but ALL zones in the list must be restored before the output is restored. Press [] to continue and skip to the Output Action prompt. B

Alpha Descriptor Programming

(*82 Menu Mode)

About Descriptor Programming
The system lets you assign zone descriptors for protection zones, keypad panics, and RF receiver supervision faults. Each description can be composed of a combination of words (up to 3) selected from a vocabulary of 196 words stored in memory (see a following page). In addition, up to 10 installerdefined words can be added to those already in memory, plus 3 additional words can be assigned as partition descriptors. Thus, when an alarm or trouble occurs in a zone, an appropriate description for that zone's location can be displayed at the keypad. Zone descriptors are recommended for systems using Alpha display keypads, and are necessary if a 4285 or 4286VIP Phone Module is used. NOTE: You can enter zone descriptors when the zone is being defined in 56 Menu mode, but we recommend you do it using 82 Menu mode.
If using a 4285 or 4286VIP Phone Module, select from those words in the Alpha Vocabulary List shown in boldface type. The phone module will not provide annunciation of the other words. If a 4285/4286 Phone Module is added to an existing system, the Alpha descriptors presently in the system should be reprogrammed, selecting from those words shown in boldface type in the Alpha Vocabulary List. The phone module will not provide annunciation of any other words.
Programming Zone Descriptors (program menu mode 82)
Descriptor programming involves: 1. Entering index numbers for up to three words from the vocabulary list for each descriptor; 2. Entering up to ten 10-digit custom words, if desired, which can then be used in descriptors. When defining descriptors: Pressing the [6] key accepts the entered index number and moves the cursor to the next position for a descriptor. Pressing the [8] key saves the entered descriptor and moves to the next descriptor. Start Zone Descriptor Programming mode by pressing *82 while in Data Programming mode. The following prompts are displayed: PROMPT
Program Alpha ? 0=No, 1=Yes 00
VALID ENTRIES Program Alpha
The Program Alpha ? prompt will appear. Press 1 to continue.
Custom Words ? 0=No, 1=Yes 00

Custom Words

The Custom Words prompt will appear. Press 0 to program standard alpha descriptors from the fixed vocabulary. The system will then automatically display the descriptor for zone 1. Press 1 to define custom words (described later in Adding Custom Words section). Note that this is a Summary mode, and that no entries can be made. Entries can be made only when the display contains a flashing cursor, which signifies the Entry mode. Press [] to continue.

ZN 01

Flashing Cursor
To delete or change the default descriptor for zone 1, press [] plus the same zone number (01). This will clear that descriptor and allow changes to be made at the flashing cursor. NOTE: If you do not wish to change the existing descriptor for zone 1, enter [] plus the next zone number for which you wish to enter (or check) a descriptor. A summary display for that zone will appear. You must then press [] plus the same zone number again to gain access to the entry mode (flashing cursor) for that zone. Press [#] plus the 3-digit number for the first word from the Alpha Vocabulary List. Example: The descriptor that we wish to enter for zone 1 is BACK DOOR. From the list, BACK = 013. Therefore, you would enter #013. Note: If you accidentally enter the wrong word, simply press [#] plus the correct 3-digit number for the word you want. Press [6] to accept the selected word and continue to the next word. NOTE: If this is the only word you are using for the descriptor, press [8] instead of [6] to save that word in memory.

ZN 01 B ACK

First 3-Digit Index No.
see index for entries [] to continue

ZN 01 BACK

Accept First Word
6 = save word and go to next word in this descriptor 8 = save word and end descriptor- go to next zone
Second 3-Digit Index No. Enter the 3-digit number for the next word. In our example, the word
see index for entries [] to continue is DOOR, whose number is 057. Enter # 7. Press [6] to accept the selected word. NOTE: If these are the only words you are using for the descriptor, press [8] instead of [6] to save them in memory. The two words in our example have now been entered. Note, however, that up to three words may be entered (provided the number of characters will fit on the screen). Press [8] to save all words in memory.

Accept Second Word

6 = save word and go to last word in this descriptor 8 = save word and end descriptor- go to next zone
The flashing cursor will disappear, indicating that the word(s) are stored in memory for that zone, as shown in the summary display at the left. To enter a descriptor for the next zone, press [] plus the desired zone number (e.g., 02). The summary display will appear. Now repeat the previous steps to enter the descriptor for the next zone. To exit the Alpha descriptor mode, press + 0 + 0 at the summary display.
Adding Custom Words (will not be annunciated by 4285/4286 Phone Module)
You can add up to 10 installer-defined words to the built-in vocabulary, which can then be used when programming zone descriptors. Each of the 10 words can actually consist of a word string of one or more words, but no more than ten characters can be used for each word or word string. When adding custom words, the keypad keys perform the following functions: [4] Moves cursor one space to the left. [6] Moves cursor one space to the right. [8] Saves the new word in the system's memory. 1. Select Custom Word mode (enter 1) when the prompt CUSTOM WORD ? is displayed. 2. Enter the number (0110 of the custom word or word string to be created, corresponding to ) index numbers 245 - 254 respectively (for example, if you are creating the first custom word or word-string, enter 01, for the second, enter 02, etc.). A cursor will now appear at the beginning of the second line. or 11, 12, 13 for partition 1, partition 2 and common partition descriptors respectively. See Assigning Partition Descriptors paragraph below. NOTE: Custom words 8, 9, and 10 are reminder words that can be programmed to display using Scheduling Mode. 3. Refer to the Character List of letters, numbers, and symbols on a following page. Press [#], followed by the two-digit entry for the first letter you would like to display (e.g., # for A). The cursor will then move to the right, in position for the next character. 4. Repeat Step 3 to create the desired word(s). Note that the 4 key can be used to move the cursor to the left, if necessary. Remember, no word or word-string can exceed 10 characters. 5. Press the [8] key to save the custom word(s) and return to the CUSTOM WORD ? display. Repeat Steps 25 for other custom words to be entered. To change a custom word, just overwrite it. If no more are to be entered now, press [0] to return to the Descriptor entry. The custom word(s) will be automatically added to the built-in vocabulary. Assigning Partition/Custom Message Descriptors VISTA-15P: You can create a custom message display that appears on alpha keypads instead of System Ready. To assign a custom message, use word number 11 as described below. VISTA-20P: You can assign a partition descriptor (up to 16 characters) for each partition plus the common lobby. Use the same procedure as for adding custom words (described above), but use the following word numbers in step 2: 11 = partition 1 ___________________________________________ 12 = partition 2 ___________________________________________ (VISTA-20P only) 13 = common lobby ________________________________________ (VISTA-20P only) Use the SPACE bar to delete existing characters. Once a custom word is entered in any of these word locations (11-13), the system displays the appropriate partitions word instead of the normal System Ready message.

Chime Mode Activate Output Devices

SUMMARY OF ARMING MODES

Arming Mode Exit Delay AWAY STAY NIGHT-STAY INSTANT MAXIMUM Yes Yes Yes Yes Yes Features for Each Arming Mode Entry Delay Yes Yes Yes No No Perimeter Armed Yes Yes Yes Yes Yes Interior Armed Yes No
only those zones listed in NightStay zone list

No Yes

Panic Keys
There are three Panic keys (A, B, and C) that, if programmed, can be used to manually initiate alarms and send a report to the central station. Each key can be programmed for 24-hour Silent, 24-hour Audible, Fire, or Personal Emergency responses. The programmed Panic response is activated when the appropriate key is pressed for at least 2 seconds. The Panic keys are identified by the system as follows:
Keys [A] (/1) [B] (/#) [C] (3/#) Displayed as Zone 96
IMPORTANT: For a Silent panic function (if programmed) to be of practical value, you must program a report code for the zone and the system must be connected to a central station.
Setting the Real-Time Clock
Set the time and date by doing the following: 1.

(Security Code)

+[#] + [6] [3]

Alpha Display:

(-7%61)( 6)%(= 83 %61 8-1)(%8) 7%8-1)(%8) 7%8 4
2. Press [] when the time/date is displayed. A cursor appears under the first digit of the hour. To move cursor ahead, press []. To go back, press [#]. Enter the 2-digit hour setting. Enter the 2-digit minute setting. Press [1] for PM or [2] for AM. Enter the last two digits of the current year. Enter the 2-digit month setting. Enter the 2-digit day setting. 3. To exit, press [] when cursor is at the last digit, or wait 10 seconds.

Current time display

Time/date editing display
Various System Trouble Displays

Alpha Display

CANCELED ALARM

Fixed Disp. Meaning

will appear if an exit or interior zone contained a fault during closing at the time the Exit Delay ended (e.g., exit door left open), but the system was disarmed during the Entry Delay time. The alarm sounder and keypad sound continuously, but stop when the system is disarmed. No message will be transmitted to the central station. will appear when the Exit Delay ends if an exit or interior zone contained a fault during closing. The alarm sounder and keypad sound continuously until the system is disarmed (or timeout occurs). An Exit Alarm message is sent to the central station. Also results if an alarm from an exit or interior zone occurs within 2 minutes after the end of an Exit Delay. indicates that a problem exists with the displayed zone(s) and requires attention. Note: The control will sense a high resistance in the loops on hardwired zones 28 and display CHECK and the affected zone number when the system is in the disarmed mode. It will not be possible to arm the system as long as this condition exists (unless this zone is bypassed). If the system is in the armed mode when the high resistance condition occurs, this display will not appear, but will do so as soon as the system is disarmed. Check the sensor or the loop wiring for the displayed zone. indicates that communication between control and a zone expander or wireless receiver is interrupted, where xx is the device address. Check the wiring and DIP switch settings on the units. If field *199 is set to 1, all ECP module problems are displayed as 91. If there are wireless sensors in the system, the Check condition may also be caused by some change in the environment that prevents the receiver from receiving signals from a particular sensor. with no zone number indicates that the system's main standby battery is weak. with a zone number and a once-per-minute beeping at the keypad indicates that a low-battery condition exists in the wireless sensor displayed (zone 00 indicates a wireless keypad). If the battery is not replaced within 30 days, a CHECK display may occur. NOTE: Some wireless sensors contain a non-replaceable long-life battery which requires replacement of the entire unit at the end of battery life (e.g., Nos. 5802, 5802CP). Telephone Line Failure, indicates that a monitored telephone line (if programmed in field *92) has been cut or disconnected. Depending on how the system was programmed, the keypad may also produce a trouble sound, and the external sounder may be activated. Silence by entering installer code + OFF. If this remains displayed for more than 1 minute, the system is disabled. The system is in communication with the central station for change of function or status verification. Power Failure If there is no keypad display at all and the LEDs are unlit, operating power (AC and battery) for the system has stopped and the system is inoperative. If the message AC LOSS (Alpha display keypads) or NO AC (Fixed-Word display keypads) is displayed, the keypad is operating on battery power only. If the battery standby capacity is used up during a prolonged AC power outage, the control's power will shut down to minimize deep discharge of the battery. A communication failure has occurred. The keypad is not receiving signals from the control and sees an open circuit. Backup LRR communication failure. Bell supervision failure. RF jam detected. Wireless keypad low battery The dialer test has been successful (CID code 601). The dialer is disabled. Walk test mode is active(CID code 607). The upload or download session was completed. The upload or download session failed before completion.

Dialer Communication Test and Periodic Test Reports
1. Enter Installer Code + 5 [TEST], then press 1 at the prompt to start the Dialer Test.
The following will be displayed (accompanied by 2 beeps) if test is successful:
PHONE OKAY (Cd displayed on Fixed-Word Display Keypads)
A Contact ID report will also be sent (code 601) If the dialer test is unsuccessful, the following is displayed:
COMM FAILURE (FC displayed on Fixed-Word Display Keypads)
2. Enter installer code + OFF to clear the display and exit. Automatic Periodic Test Report The system can be set to automatically send test reports (enabled in field *64; Contact ID code 602) at specified intervals. Frequency of the reports is set in Scheduling mode (event 11) or by the following key commands:
installer code + [#] + 0 + 0 = test report sent every 24 hours installer code + [#] + 0 + 1 = test report sent once per week installer code + [#] + 0 + 2 = test report sent every 28 days
Each mode sets schedule 32 (VISTA-20P) or schedule 08 (VISTA-15P) to the stated repeat option; first test report sent 12 hours after command. To ensure that test reports are sent at the times expected, set the Real-Time Clock to the proper time before entering the test report schedule command. Automatic Standby Battery Tests 1. An automatic test is conducted every 3 minutes to ensure that a standby battery is present and properly connected. If a battery is not present or is not properly connected, a LOW BATTERY message is displayed and, if so programmed, will be reported to the central station. 2. A battery capacity test is automatically conducted for 2 minutes every 4 hours, beginning 4 hours after exiting the Programming mode or after powering up the system. In addition, entry into the Test mode will also cause a battery capacity test to be initiated. If the battery cannot sustain a load, a Low Battery message is displayed and, if so programmed, will be reported to the central station.
Specifications & Accessories

SECURITY CONTROL

Sounders:

5800 Series Transmitter Input Loop Identification
All of the transmitters illustrated below have one or more unique factory assigned input (loop) ID codes. Each of the input loops requires its own programming zone (e.g., a 5804's four inputs require four programming zones).

LOOP 3

LOOP 2

(REED)

LOOP 1

(PRIMARY)

LOOP 2 LOOP 1 LOOP 4 YOU MUST ENROLL THIS BUTTON
5801 ENROLL AS "UR" OR "RF"

LOOP 1 (TERMINALS)

(AUX. CENTER)
ALTERNATE POSITION FOR LOOP2

(AUX. RIGHT)

NOTE: For information on any transmitter not shown, refer to the instructions accompanying that transmitter for details regarding loop numbers, etc. UL NOTE: The following transmitters are not intended for use in UL installations: 5802MN, 5802MN2, 5804, 5804BD, 5814, 5816TEMP, 5819, 5819WHS & BRS, and 5850.
5802MN ENROLL AS "UR" OR "RF"
5816MN ENROLL AS "RF"
5817 ENROLL AS "RF"
YOU MUST ENROLL THIS BUTTON LOOP 4

LOOP 3 LOOP 2 LOOP 1

5804 ENROLL AS "BR"

LOOP 3 (TERMINALS)
LOOP 1 (INTERNAL SHOCK SENSOR)
5819 ENROLL AS "RF"
5819S (WHS & BRS) ENROLL AS "RF"

SET HOUSE CODE

5827 SET HOUSE CODE

5827BD SET HOUSE CODE

5804BD ENROLL AS "BR"
LOOP ENROLL AS "RF"

(Green)

(Red) (Yellow)

(MOTION)

5816 ENROLL AS "RF"
5850 (GBD) ENROLL AS "RF"
5890 ENROLL AS "RF"
Compatible 5800 Series Transmitters Table

Model 5801

5802CP

5802MN

5804BD
Product Wireless Panic Transmitter

Pendant (Personal

Emergency Transmitter)

Input Type UR or RF

BR Only

UR or RF

REMOTE KEYPADS AND OTHER ADDRESSABLE DEVICES (e.g. 5800TM, 4285/4286, LRR, 4219, 4229, 4204, 5881)

ZONE PAIRS

POWER SHUTDOWN NOTE: SYSTEM SHUTS DOWN SENSOR DETECTION PROCESSING IF CONTROL'S VOLTAGE DROPS BELOW 9.6V.
CONNECTION OF THE FIRE ALARM SIGNAL TO A FIRE ALARM HEADQUARTERS OR A CENTRAL STATION SHALL BE PERMITTED ONLY WITH THE PERMISSION OF THE LOCAL AUTHORITY HAVING JURISDICTION. THE BURGLAR ALARM SIGNAL SHALL NOT BE CONNECTED TO A POLICE EMERGENCY NUMBER.
FOR COMPLETE INFORMATION, SEE INSTRUCTIONS K5305-1V1
NOTE: KEYPAD (S) CURRENT (IN BOTH PARTITIONS) AND ALL OTHER DEVICES DRAWING POWER FROM TERMS 4 & 5 MUST BE INCLUDED IN AUX CURRENT DRAIN CALCULATIONS.

2 / / / / / / / 16

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM. IN ADDITION, THIS SYSTEM MUST BE CHECKED BY A QUALIFIED TECHNICIAN AT LEAST ONCE EVERY THREE (3) YEARS.
TYPICAL WIRING FOR DOUBLE BALANCED ZONE (VISTA-20P/PS ONLY)

ASSEMBLED IN MEXICO

REMOTE KEYPADS CAN USE 6150 OR 6160 KEYPADS. LOCAL PROGRAMMING MUST BE DONE WITH A 6139/6160, BUT NEED NOT REMAIN IN THE SYSTEM (SET TO ADDRESS 16).
TYPICAL WIRING FOR ZONE DOUBLING (VISTA-20P/PS ONLY)
ALL DEVICES AND ACCESSORIES USED IN A CANADIAN INSTALLATION MUST BE LISTED FOR USE IN CANADA
VISTA-20P/PS SERIES, VISTA-15P SERIES

SUMMARY OF CONNECTIONS

V20P_V15P-SOC-V0

ADEMCO LIMITED WARRANTY

Alarm Device Manufacturing Company, a Division of Pittway Corporation, and its divisions, subsidiaries and affiliates ("Seller"), 165 Eileen Way, Syosset, New York 11791, warrants its products to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for 24 months from the date stamp control on the product or, for products not having an Ademco date stamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply. Seller's obligation shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product which is proved not in compliance with Seller's specifications or proves defective in materials or workmanship under normal use and service. Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Ademco factory service. For warranty service, return product transportation prepaid, to ADEMCO Factory Service, 170 Michael Drive, Syosset, New York 11791. THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. Seller does not represent that the products it sells may not be compromised or circumvented; that the products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the products will in all cases provide adequate warning or protection. Customer understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty replaces any previous warranties and is the only warranty made by Seller on this product. No increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorised.