6HFXULW\6\VWHP

8VHU*XLGH
ARM STAY INSTANT AC/LB READY
FIRE BURGLARY INSTRUMENTS, INC.

N9819V3 6/00

Table Of Contents
QUICK REFERENCE...3 INTRODUCTION....4 SYSTEM REFERENCE....5 TURNING THE SYSTEM ON....7 TURNING THE SYSTEM OFF...10 USER CODES....11 MISCELLANEOUS COMMANDS...12 TESTING THE SYSTEM....14 NATIONAL FIRE PROTECTION ASSOCIATION RECOMMENDATIONS ON SMOKE DETECTORS....15 EMERGENCY EVACUATION...16 GLOSSARY.....17 FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT..20 TELEPHONE OPERATIONAL PROBLEMS...20 LIMITATIONS OF THIS ALARM SYSTEM...21 LIMITED WARRANTY....23

Quick Reference

TO TURN SYSTEM ON
1. Check to make sure the system is ready, (Green READY light is lit ). 2. Enter your 4-digit user code. 3. Exit through a door designated by your installer as an exit/entry door. 4. The ON/OFF (ARM) light will light.

TO TURN SYSTEM OFF

1. Enter through a door designated by your installer as an exit/entry door 2. Enter your 4-digit user code. 3. The system ON (ARM) light will go out.
TO TURN SYSTEM ON AND STAY INSIDE
1. Check to make sure the system is ready (Green READY light is lit ). 2. Press

3. Enter your user code.

The ON/OFF (ARM) light and the STAY light will both light.
REMEMBER: You must turn the system OFF if you want to open the door or leave the premises after the exit time has passed.
TO TURN THE SYSTEM ON: INSTANT MODE, AND STAY INSIDE
1. Check to make sure the system is ready (Green READY light is lit ). 2. Press 3. Press

INSTANT. STAY.

4. Enter your user code.
The ON/OFF (ARM) light, the INSTANT light, and the STAY light will all be on.

TO RESET SMOKE DETECTOR

1. Enter your 4-digit user code.
READY light is not available on all keypads.

Introduction

Congratulations on your decision to protect your home or business with the XL-2T security system. You have chosen a reliable, state-of-the-art security system that is remarkably easy to operate. Your system has been professionally installed by your local Security Company whose representative can explain the specifics of your system. The keypad is the input and display device for your security system. Your Security Company representative will suggest the model most appropriate for your premises and your needs. The XL-2T is listed by Underwriters Laboratories for Household Fire and Burglary applications. Throughout this manual, the following conventions are used to represent the keystrokes required to perform the following functions.

STAY BYPASS INSTANT CODE

Press button labeled STAY. Press button labeled BYPASS. Press button labeled INSTANT. Press button labeled CODE. Enter 4-digit user code.
Please keep your manual in a convenient location so you can refer to it if needed.

System Reference

ZONE DESCRIPTIONS
In the following table, enter a description of the area of protection for each zone. Example: Zone 1 Windows on North side of building Zone 4 Main entrance to building. ZONE 7 DESCRIPTION ______________________________________
Entry time ________ Door __________ Exit time ________ Entry time ________ Door __________ Exit time is the same for all designated Entry/Exit doors.

SEND-HELP ALERT

All keypads are equipped with emergency-pair keys. In order to activate the alert, both keys must be pressed at the same time. The type of keypad you have installed dictates which keys you press. Your installer will show you how to activate these emergency keys. The emergency keys used for all keypads are shown below. The following SEND - HELP ALERT is programmed into my system: KEYS [#] & [] (Right ) [7] & [9] (Left ) [1] & [3] (Center )

DESCRIPTION __________________________________ __________________________________ __________________________________
Buttons on XL-4600SM keypad only

System Reference (cont)

USER CODE ASSIGNMENTS
In the following table, enter the names of the individuals assigned to each specific User ID number. USER ID ASSIGNED TO 1 (MASTER USER * ) 2 (MASTER USER * ) 3 4** 13 Door Strike - Yes No If No ______________________ (If user 13 is not assigned to door strike, then any user can activate the door strike.) 14 Only Turns System ON -Yes If No __________________ 15 Ambush/Duress Code -Yes If No ___________________
* Master Users can add, change, or erase other user codes. ** If your installer enables only User 4 to report openings and closings to the CS, then only those person(s) that you assign User 4 ID to will cause a report to be generated.
MONITORING STATION INFORMATION

Account # Telephone #

Turning The System On
IS THE SYSTEM READY? You can turn the burglar portion of your security system ON and OFF. Before you can turn the system ON, it must be ready. If you have a protected door open, or someone is moving in view of a motion detector, the system will not display READY. The system is ready if the READY light is ON or if the display shows: SYSTEM READY
WHEN SYSTEM IS NOT READY If the system is not ready to be armed, the READY light will be OFF and the zone lights will show which zone or zones are not ready. The following conditions will be indicated by the zone lights or described on the display: Fast Blink.. Alarm Slow Blink/Low Intensity.. Bypass Slow Pulse.. Trouble Solid ON.. Not Ready Example: If the READY light is not lit and the Zone 1 light is solid ON, an alarm sensor on Zone 1 is faulted. This might mean that a door is open or someone is walking in view of a motion sensor. Check all sensors on Zone 1 and resolve the problem. When all sensors are restored, the READY light will come ON and the zone light will go out. In this example, the display shows: SYSTEM NOT READY and NOT RDY ZONE 1 FRONT DOOR
Determine which zone or zones are not ready, resolve the problem, and turn the system ON normally. If the problem cannot be resolved, you may bypass the zone that is not ready. Bypassing should only be done if the problem on the zone cannot be resolved, OR if you intentionally wish to leave the zone OFF. For example, you would leave the zone OFF if you plan to keep the window open for ventilation. Zones that are bypassed are not protected when the system is ON. See Bypass on the following page for a description of the procedure.

Turning The System ON (cont)
TO TURN SYSTEM ON AND LEAVE Enter your 4-digit user code. The System ON, (ARM) light will go ON or the display will show: ON: AWAY. Exit through a door designated by your installer as an exit/entry door. You must leave within the exit time programmed by your installer. Refer to the reference sheet for the time that has been set for your system. TO TURN SYSTEM ON AND STAY INSIDE To turn the perimeter portion of your burglar alarm ON and move around freely inside the premises, use the STAY mode. Check to make sure the system is ready. When it is ready, press: STAY followed by your user code.
When the system has been turned on successfully, the ON/OFF (ARM) light and the STAY light will be lit, or the LCD will display: ON: STAY REMEMBER: You must turn the system OFF if you want to open the door or leave the premises after the exit time has passed. TO TURN SYSTEM ON IN INSTANT MODE AND STAY INSIDE In INSTANT STAY mode, the perimeter portion of your burglar alarm system is ON and the time delays are eliminated from your normal Entry/Exit door(s). All interior protection is OFF, so you are free to move around inside. Check to make sure the system is READY. When it is ready, press: INSTANT STAY followed by followed by your user code.
When the system has been turned ON successfully, the ON/OFF (ARM) light, the INSTANT light, and the STAY light will all be ON, or the LCD will display: ON: STAY INSTANT
NOTE: This system can be programmed by the installer for the AUTO-STAY feature which automatically bypasses interior zones if you arm the system and do not exit through a delay zone during exit time. TO TURN SYSTEM ON IN INSTANT MODE In INSTANT mode, all alarm sensors, including those on doors and windows, will report an alarm immediately if activated. Check to make sure the system is ready to be armed (no faulted zones). When it is ready, press: INSTANT followed by your user code.
When the system has been turned ON successfully, the ON/OFF light and the Instant light will be ON, or the LCD will display: ON: INSTANT TO BYPASS A ZONE The Bypass function excludes a zone of protection from the security system until it is unbypassed (either by using the unbypass procedure or when you turn the system OFF). Bypassing can only be done while the system is turned OFF. Press the BYPASS button. Then enter your user code and the zone number (1-7) to be bypassed, as follows: BYPASS
followed by your user code

+ ZONE #

If the Quick Bypass feature has been enabled by the installer, the user code is not required when bypassing zones. NOTE: Bypassed zones are NOT protected when the system is turned ON. After the bypass command has been accepted, the keypad will sound one long beep, and the zone LED of the zone(s) bypassed will slowly blink, or the LCD will display: IMPORTANT: Temporary users (i.e., baby sitters, housekeepers, etc.) should not be shown the Bypass procedure.

BYPASS ZONE 01 FRONT DOOR
TO UNBYPASS A ZONE Pressing the BYPASS button returns a bypassed zone to normal operation. To unbypass a zone(s), repeat the bypass function as follows: BYPASS followed by your user code + ZONE #.
After unbypassing, the zone display will show the state of the zones. -9-

Turning The System OFF

When you turn the system OFF, you turn OFF only the burglar portion of your system; any smoke or heat detectors and panic keys will remain ON. You must enter through a designated entry door and turn OFF the system within the time allowed. You can have different amounts of time for different entry points. See your system reference sheet for the times established for your system. To turn your system OFF: Enter your 4-digit user code. If no alarms have taken place, the ON/OFF light (labeled ARM) will go OFF, or the display will show: SYSTEM READY If alarms occurred when the system was ON, or if a trouble condition exists, the zone LED's will indicate it, as follows: Fast Blink.. Alarm Slow Blink/Low Intensity.. Bypass Slow Pulse.. Trouble Solid ON.. Not Ready or the LCD will display: ALARM ZONE 1 FRONT DOOR Burglary alarms will sound a steady tone at the keypad(s), and fire alarms will generate a pulsing sound. IMPORTANT: If an intrusion has taken place while you were away, do not enter until the location has been checked. Call for help from a neighbor's house and wait there for the police. After you have turned the system OFF with your user code, the LCD keypads will display this message: ALM MEM ZONE 1 FRONT DOOR To clear the display of alarm or trouble conditions and silence the audible alert: Enter your 4-digit user code - 10 again.

User Codes

TO ADD OR CHANGE A USER CODE Users can be added or changed directly at the keypad. Your system can have up to 15 different user codes. Users #1 and #2 are the only users allowed to add or delete other user codes. To add or change a user code, press the CODE button followed by user #1 or user #2 of the 4-digit user code. Then enter the new user number and the new 4-digit user code. The keypad will beep after each digit is pressed.
User #1 or #2 Code User ID New User Code
Use the system reference sheet to record system users. On this sheet your installer will indicate if you have chosen to dedicate a user code to send an emergency Ambush or Duress signal. You may also have chosen to reserve one user code that is only allowed to turn the system ON. This code will NOT be able to turn the system OFF. TO DELETE A USER CODE To delete a user, press the Code button followed by the 4-digit master user code. Enter the the user number, then press [#] to delete. For example, to delete user 3, do the following:
Master User Code User ID # to delete
NOTE: User #1, the master user, cannot be deleted but it can be changed using the ADD OR CHANGE user procedure. THE ARM-ONLY CODE (Maid Code) If you choose to have a code that cannot turn the system OFF, but can turn the system ON, have your installer program this feature. If programmed, user code 5 will have System ON capability only, and you can issue this code to a temporary user so he can secure the premises when he leaves.

- 11 -

Miscellaneous Commands
SEND HELP ALERTS Your system can be programmed for 3 separate keypad Send Help alerts that would send an emergency signal to your Central Station. See the System Reference sheet to see which have been programmed for your system. AMBUSH/DURESS Your system can be programmed to send an emergency signal to the Central Station if you are forced to enter the premises or are under duress of any kind. If you choose to include this feature, User Code 15 is dedicated to this function, and must only be used under these circumstances. QUICK ON (QUICK ARMING) If programmed by your installer, Quick ON, or Quick Arming, allows you to turn the system ON to the AWAY mode without entering a user code. NOTE: Turning your system OFF always requires a valid user code. Press [#] [1]. QUICK FORCED ON If programmed by your installer, Quick Forced ON allows you to turn the burglar portion of your alarm system ON to the AWAY mode, bypassing all zones that are not ready. Press [#] [2]. NOTE: A valid user code is still required to turn the system OFF. NOTE: This feature is disabled on UL installations. QUICK BYPASS If you have Quick Bypass programmed for your system, you will not have to use your user code to bypass zones. The Quick Bypass procedure is: BYPASS ZONE (1 - 7)
NOTE: Bypassed zones are not protected when the system is turned ON. After the bypass command has been accepted, the keypad sounds one long beep. The zone light of the bypassed zone(s) will slowly blink, or the display will show: BYPASSED: ZONE 1 FRONT DOOR NOTE: Temporary users (i.e. baby sitters, housekeepers, etc.) should not be shown the Bypass procedure. - 12 -
Miscellaneous Commands (cont)
TURN CHIME ON/OFF Chime is an optional feature that causes the keypad to chime when selected doors are opened while the burglary protection is OFF or disarmed. Only your installer can program a zone for the Chime feature. Once programmed, you can turn Chime ON or OFF to meet your daily needs. To turn Chime ON or OFF: Press [#] [6]. SET AUTO ARM ON TIME Setting Auto Arm ON time lets you set the time of day your system will automatically turn ON. To activate Set Auto Arm ON time: Press [#] [5] [hour] [minute]. The two digit settings for hours and minutes are in the 24-hour format. Example: 7AM=07; 3PM=15. Set minutes the same way: 5min=05; 25min=25. The readout keypad will prompt you for the required entries. DOOR STRIKE Door strikes are used in access control applications. To activate door strikes: Press [#] [9] [User Code] [Door #] where the door number is as follows: 1 ________________________ 2 ________________________ NOTE: User 13 is the only user code that can perform the door strike function. VIEW TIME To view the time, press: [#] [7]. CURRENT TIME: 08:15AM SET TIME To set the time and date, press: [#] [3] [user 1 or 2 code] [hr1] [hr2] [min1] [min2] [mnth1] [mnth2] [day1] [day2] [year1] [year2] (The user code is not required if so programmed by installer.) TO VIEW AUTO ARM ON TIME To view the auto arm time, press: [#] [8] [user 1 or 2 code]. AUTOARM TIME: 05:00PM (The user code is not required if so programmed by installer.) - 13 -

Testing The System

SYSTEM TEST It is recommended that you test your system once a week using the following procedure: NOTE: If your system is monitored, contact your Central Station before you perform this test. 1. Turn your security system ON. 2. Wait until your exit time is over. Then activate the system by opening a protected zone (for example: a window or door). 3. Confirm that the alarm sounding device (bell or siren) sounds. If your system is connected to a Central Station, the keypad will sound the ringback tone to confirm that the signal was received. 4. Turn the security system OFF. 5. Call the Central Station to tell them you are finished testing. BATTERY TEST It is recommended that you test your battery once a month. In order to test your backup/standby battery, the following procedure should be followed: 1. Unplug the transformer from the AC outlet by removing the restraining screw that secures the transformer to the wall. (NOTE: The screw is not present on the models sold in Canada.) 2. Observe that the AC indicator light on the keypad goes OFF. 3. Activate your alarm by performing the above SYSTEM TEST. Remember to contact your Central Station if your system is monitored. 4. Plug the transformer into the AC outlet and secure with the restraining screw. (NOTE: The screw is not present on the models sold in Canada.) The National Fire Protection Association publishes a standard for fire warning equipment (NFPA publication #72). Further information can be obtained by contacting: NFPA Public Affairs Dept., Batterymarch Park, Quincy, MA 02269. If you have any further questions about the operation of your system, please contact your alarm company.

- 14 -

National Fire Protection Association Recommendations On Smoke Detectors
With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Associations (NFPA) Standard #72 noted below. Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows: A smoke detector installed outside of each separate sleeping area, in the immediate vicinity of the bedrooms and on each additional story of the family living unit, including basements, and excluding crawl spaces and unfinished attics. In addition, the NFPA recommends that you install heat or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements, and attached garages.

KITCHEN DINING

BEDROOM BEDROOM

TV ROOM

KITCHEN DINING LIVING ROOM

BDRM BDRM

LIVING ROOM

BEDROOM

Smoke Detectors for Minimum Protection Smoke Detectors for Additional Protection BEDROOM TO BR Heat-Activated Detectors

BEDROOM KTCHN

LVNG RM BASEMENT

CLOSED DOOR

GARAGE

- 15 -

Emergency Evacuation
Establish and regularly practice a plan of escape in the event of fire. The following steps are recommended by the National Fire Protection Association: 1. Position your detector or your interior and/or exterior sounders so that they can be heard by all occupants. 2. Determine two means of escape from each room. One path of escape should lead to the door that permits normal exit from the building. The other is an alternative route, such as through a window, should your normal escape path be unpassable. Station an escape ladder at such windows if there is a long drop to the ground. 3. Sketch a floor plan of the building. Show windows, doors, stairs, and rooftops that can be used to escape. Indicate escape routes for each room. Keep these routes free from obstruction and post copies of the escape routes in every room. 4. Assure that all bedroom doors are shut while you are asleep. This will prevent deadly smoke from entering while you escape. 5. Try the door. If the door is hot, check your alternate escape route. If the door is cool, open it cautiously. Be prepared to slam the door shut if smoke or heat rushes in. 6. When smoke is present, crawl on the ground. Do not walk upright, since smoke rises and may overcome you. Clearer air is near the floor. 7. Escape quickly; dont panic. 8. Establish a common meeting place outdoors, away from your house, where everyone can meet and then take steps to contact the authorities and account for those missing. Choose someone to assure that nobody returns to the house many die going back.

M ET OO OS DR CL BE

M M OO OO TH DR DR BA BE BE

2ND FLOOR

N HE TC KI BACK DOOR M OO DR BE

M OO TH DR BA BE

1ST FLOOR

- 16 -

Glossary
AC INDICATOR: Small green power ON/OFF light between the center buttons on the keypad. When lit, the system is running on primary power; when not lit, the system is running off the backup battery. ALARM: Sound from keypad or other horn/siren indicates a burglar alarm, fire alarm, or other condition you should be alerted to. ARMED: See ON/OFF. AWAY: A system setting that protects the premises while it is unoccupied. All burglary sensors are active. BURGLARY/FIRE: The two major functions of a security system. Fire protection is always ON and cannot be turned OFF. The burglary sensors protect against unauthorized entry into your premises. The burglary protection can be turned ON and OFF and programmed for special levels of access and notification. BYPASS FEATURE: The Bypass feature allows you to exclude a selected zone or zones from the burglar alarm protection. BYPASS BUTTON: A button on the keypad used to activate the Bypass feature. CENTRAL STATION: The signal monitoring center contacted by your security system over the telephone and/or other communication channels when alarms are activated, if your system is programmed to communicate alarms off site. The Central Station will follow their procedures and your instructions for contacting the proper authorities when a signal is received. CHIME FEATURE: An optional feature that causes the keypad to chime for one second when selected doors are opened when the burglary protection is OFF or disarmed. Once programmed by your installer, you can turn Chime ON and OFF with #6. DISARMED: See ON/OFF system feature that you may have programmed into your system. If someone forces you to turn your system OFF, entering the special Ambush/Duress user code turns the system OFF and sends a silent emergency signal to the Central Station so personnel there can respond appropriately. ENTRY DELAY: The period of time allowed between opening a designated Entry/Exit door and turning OFF the alarm system before the system will register an alarm condition. This is determined at the time of installation. Your system supports two entry times, allowing you to have a different length of time for different doors.

- 17 -

Glossary (cont)
EXIT DELAY: The period of time allowed between turning the system on and leaving through a designated exit/entry door before the system will register an alarm condition. This is determined at the time of installation. INTERIOR ZONE: An interior zone is a group of points that protect the interior of your premises. You may want to turn the perimeter portion of your system on while leaving the interior zones OFF to allow you to open interior doors and pass interior motion detectors without causing an alarm. KEYPAD: A keypad is your link into your system. It displays alarm and trouble messages, shows faulted zones and allows you to turn the system ON or OFF by using the buttons. Your system will have one or more keypads. ON/OFF: These terms refer to the burglary portion of your security system. There are several levels of operation that allow you to protect part of your premises while you remain inside. Fire sensors and other emergency and environmental features are always active and ready; they are not affected in any way by turning the burglary portion of your security system ON or OFF. Other terms used are "armed" (system is on) and "disarmed" (system is OFF). See ON-INSTANT, ON-STAY, and STAY. ON/OFF INDICATOR: Red light in the upper portion of the keypad labeled "Armed." When lit, some part of the burglar alarm system is ON; when not lit, the burglary portion of the system is OFF. ON-STAY: A system setting that turns ON the perimeter protection of the building but allows movement throughout the interior. PANIC BUTTON: A push button that allows you to signal the Central Station that you need immediate assistance. Your system has programmable Keypad Send Help Alerts that can also serve as Panic buttons. PERIMETER ZONE: A perimeter zone is a group of points that protect the exterior of your premises. Your outside doors and windows would be programmed as a perimeter zone.

- 18 -

SENSOR: The actual alarm sensor, detector, or device installed to detect an intrusion, fire, or environmental problem. Examples include: door contacts, window contacts, motion sensors, glassbreak sensors, smoke detectors, rate-of-rise heat detectors, temperature sensors, flood/water sensors, and carbon monoxide gas detectors. SILENT CONDITION: Most types of alarms and troubles alert you with the keypad sounder and the sirens, horns, or speakers located in your premises. The intent is to advise you of the alarm or trouble and allow you to respond promptly. The audible sounds also let an intruder know that he has been detected and will hopefully scare him away. In some circumstances, an audible alarm might put your life in danger. For that reason, those alarms are programmed as silent conditions. For an example, see AMBUSH/DURESS. SYSTEM: Your security system is composed of three main parts: 1) the control panel, which functions as the system brain and the link to the monitoring agency (Central Station); 2) the keypad(s), which provide you with system status and allow you to input commands; 3) security sensors such as door and window contacts, motion sensors, smoke detectors, and other sensors as required to detect intrusion, fire, and other conditions for your premises. USER CODE: A user code is a 4-digit code that is required to operate the system. The system supports up to 6 separate user codes. The system supports one master user who can add/delete other user codes. Two of the user codes may be dedicated to special functions as defined by your alarm company at the time of installation. (See the User Code List in the back of this manual) ZONE: A zone is a collection of sensors with common characteristics grouped together for your operating convenience. The system will support 6 zones or groupings.

- 19 -

FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type-tested and found to comply with the limits for a class B computing device in accordance with the specifications in Subpart J Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment on, the user is encouraged to try and correct the interference by one or more of the following measures: If using an indoor antenna, have a quality outdoor antenna installed. Re-orient the receiving antenna until interference is reduced or eliminated. Move the receiver away from any wire runs to the control/communicator. Plug the control/communicator into a different outlet so that it and the receiver are on different branch circuits. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user or installer may find the following booklet prepared by the Federal Communications Commission helpful: "Interference Handbook." This booklet is available from the U.S. Government Printing OFFice, Washington, DC 20402. The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User Guide. Unauthorized changes or modifications could void the user's authority to operate the equipment.
TELEPHONE OPERATIONAL PROBLEMS
In the event of telephone operational problems, disconnect the control by removing the plug from the RJ31X wall jack. We recommend that your certified installer demonstrate disconnecting the phones on installation of the system. Do not disconnect the phone connection inside the control/communicator. Doing so will result in the loss of your phone lines. If the regular phone works correctly after the control/communicator has been disconnected from the phone lines, the control/communicator has a problem and should be returned for repair. If upon disconnection of the control/communicator, there is still a problem on the line, notify the telephone company that it has a problem and request prompt repair service. The user may not under any circumstances (in or out of warranty) attempt any service or repairs to the system. It must be returned to the factory or an authorized service agency for all repairs. This control unit was manufactured under rigid quality standards and complies with all UL requirements for its intended use. Maintenance is best performed by your installing company with trained service personnel.

- 20 -

LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary, fire, or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example: Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work without batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. A user may not be able to reach a panic or emergency button quickly enough. While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with the System may not work are as follows: Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending on the nature of the fire and/or the location of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death. Passive Infrared Motion Detectors can only detect Intrusion within the designed ranges as diagrammed in their Installation and Setup Guide. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and Intrusion can only be detected in unobstructed areas covered by the beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying, of any material on the mirrors, windows, or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of the protected area approaches the temperature range of 90 degrees to 150 degrees Fahrenheit, the detection performance can decrease.

- 21 -

LIMITATIONS OF THIS ALARM SYSTEM (cont)
Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers who are located on the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo, radio, air conditioner, other appliances, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers. Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. However, even if the system responds to the emergency as intended, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors are working properly. Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners, and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments.

- 22 -

LIMITED WARRANTY
Fire Burglary Instruments, Inc., a subsidiary of Pittway Corporation, and its divisions, subsidiaries and affiliates ("Seller"), 149 Eileen Way, Syosset, New York 11791, warrants its security equipment (the "product") to be free from defects in material and workmanship for one year from date of original purchase, under normal use and service. Seller's obligation is limited to repairing or replacing, at its option, free of charge for parts, labor, or transportation, any product proved to be defective in materials or workmanship under normal use and service. Seller shall have no obligation under this warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than the Seller. In case of defect, contact the security professional who installed and maintains your security equipment or the Seller for product repair. This one year Limited Warranty is in lieu of all other expressed warranties, obligations or liabilities. THERE ARE NO EXPRESS WARRANTIES, WHICH EXTEND BEYOND THE FACE HEREOF. ANY IMPLIED WARRANTIES, OBLIGATIONS OR LIABILITIES MADE BY SELLER IN CONNECTION WITH THIS PRODUCT, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, ARE LIMITED IN DURATION TO A PERIOD OF ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE, ANY ACTION FOR BREACH OF ANY WARRANTY, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY, MUST BE BROUGHT WITHIN 60 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. Some states do not allow limitation on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Seller does not represent that the product may not be compromised or circumvented; that the product will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate warning or protection. Buyer understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHILE SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. No increase of alteration, written or verbal, to this warranty is authorized.

8&10

12(.)&15(+)
XL-2 HOOKUP & INSTALLATION Page 6
120NSTANT DC POWER rhlsteminal detivera constant unregulated 10.0-15.5VDC power fordevi@s requiring a constant power such as VS279. It is mnnected to a bell fuse (F3). 13ELLOUTPU~ rhe total output Wwer available for sounding devices is 1 amp at 10.5 -15.5 \/DC for residential applications, or 12.0 -14.4 VDC for commercial installatbna (750 mA for UL installations). These terminals will dehver CONSTANT output [m BURGLARY, AUDIBLE PANIC and BELL TEST. On a FIRE mndiimn, a PULSED Output will be generated, There are separate bell cutoff times programmable for Burglary and Rre Condtions within the programrni~ $equenm. For UL Household Hre Warning System installations, the speaker is required to be mounted indoors for best audibi~iy. Also, for UL installafiins, lise only one speaker.

22(+) & 23(-)

24& 25
lrRANSFORMER: (>onnect the12VAC 20VAtraneformer, utihzing 18awgwireat adstanul to exceed 15 feet from the panel, to an unswltched 120 VAC outlat. Mt
[10not use any other transformer since this may resu~ in improper operaticm or clamage to the unit. The AC/LOW BAT LED onthekeypad will remain ON, while AC~weris ~~resent.If an AC loss occurs the AC/LOW BAT LED will turn off immediately. II AC remains OFF for 15 minutes, the system will pulse the ke~ad buzzer and transmit to the central etation, if programmed, THE KEYPAD BUZZER CAN BE SILENCED by ent~ of any valid user code. When AC restores the AC/LOW [3AT LED will light immediately, and a restore code will be reptied, K ~Jrogrammed. BACKUP BA~ERY: lrhe RED(+) and BLACK(-) flying leada must be connected to a 12 VDC 4-6AH GELL CELL, to sewe as ba~up Wwer in the event of AC loss. /! battery test occurs approximately eve~ 4.5 minutes. Low bafte~ mtiion CJccursat nominal 11VDC. The keypad AC/LOW BAT LED and buzzer will IJULSE SLOWLY when low battery condition is detected. The System rar~rta this condition to the CS f programmed. Battery resforal will oscur WITHIN 4.5 minutes, at the NEXT battery test. THE BUZZER MAYBE SILENCED by (!ntry of any vatid user code. (;round start capa~~iy can be added to the system through addiiin of the FBII Model 117 module. Consult the 117 Installation hretructions for hookup information. NOTE: The 117 module has not been tested for use inj UL installations,

MOUNTING KEYPAD INCONTROLPANEL ENCLOSURE AL*.+,;:::: -:-- (1 1- Remve keypad knockout from flonf of metal box enclosure as shown. 2-insert XL4600RM into opening from front of encloeure. 3- Secure keypad to enclosure using the four painted metal ecrews and nuts provided.
: :ur:ll~~1 I H Cj [J 1~1 ~~n[gijf~j ] 1 ,,.UU[30 ! ,. D a C_ J
XL-2HOOKUP&lNSTALLAT10N

XL4SOOSM KEYPAD

A. Directly to a control panel having a keypad cutout on the front of its enclosure, B. ~}re~ly to a single or double gang electrical junction box. C. Oirecfly to a wall or other surface. 1, Remve the keypad cover assembly from the rear munting plate. Insert a small screwdriver blade in the COVER PRY-OFF SLOTS at the lower edge of the keypad (see Oiagram 2 ) and W!st to pry off the cover assembly. 2. Mount the rear plate (see Diagram 3). Note: The plate is correctly oriented when ifs part number, molded into the plastic, is upright. A. MOUNTING DIRECTLY PANEL ENCLOSURE: TO CONTROL
The XL4612SM Keypad may be surface rncunted in the following way6
If the control panel has a keypad wtout on the front face of its enclosure, remove the cutout and mount the plate to the anclosuras face via HOLES N ( eee diagram 3) and the four screws and nuts provided. Diagram 2: BOTTOM VIEW OF KEYPAD Note: The XL3B attack-proof enclosures does not contain a keypad cutout. B. MOUNTING DIRECTLY TO AN ELECTRICAL JUNCTION BOX: The plste can be mcunfed directly to a single or double gang electrical junction Wx. Uae the screwholes provided and HOLES B for a single gang box or HOLES A for a double gang box. C. MOUNTING DIRECTLY TO A WALL OR OTHER SURFACE Provide a wiring hole in the mounting surface. Position the plates WIRING OPENING over the hole and mounting plate, using HOLES A andor B in conjunction with appropriate mounting hardware (not provided) for the type of surface. 3. Complete the keypad wirl~ ae required for the wntrol with which the ke~ad is to be used. 4. Replace the keypad cover assembly on the rear plate. Staning at the upper edge of the plate, engage the plates two HOLDING HOOKS (sea diagram 3) into the recesses provided for them inside the upper edge of the wver assembly and snap the lower edge of the rover assembly and snap the lower edge of the cover onto the two SNAP HOOKS at the lower edge of the plate. Nofe: (Optional) If desired, mverandplate can& further secured together by inserting a ecrew (provided) into the SLOT at the keypada lower edge.

Diagram

3: REAR MOUNTING
XL-2 HOOKUP & INSTALLATION Page 10
MOUNTING 6805 and 8615 KEYPADS
Keypad munting is tientical for both the 6615 LED and 6605 LCD versions. Keypads can be surface mounted or flush mounted as described bebw. NOTE: After mounting the W05 LCD Keypsd at eye level, you can a~ust the display intet ,sity level to suit the user by adjusting the intensity control hated behind the keypad door. SURFACE MOUNTING ~ b o.% o 8.%) ~ 1. Select a mounting location and Pla[cethe rear plate of thekeypad 6nthewa11. Ma~lhe location of thecutout forthekeypad wiring catlle. 2-Create a keypad opening. Connect the keWad wiring to the control panel w/ 4-wire connector. 3- Place the keypad wiring through thf?cutout and secure the backplate to the wall (see dagram). r] 4- Connect the keypad wiring conm?ctortothe keypad andplace thekeypad on the munling plate attached to the wall. 5- Secure the keypad to the rear mounting plate by attaching the 5/8 inch screw provided in the lower hole, located betind the keypa[i door. RECESSED MOUNTING 1- Select a mounting location, For receeeed mounting thie must be between two etude.The rear mounting plate is not used for recessed installations. 2- Create an opening in the wall exa(fily 4 inches high by 5 13/16 inches wide. 3- Turn over the keypad and rewve the PMllilps head screw (item 1 on diagram) in ttie upper left hand eide of the keypad printed circuit bead. Note: This screw is located immediatt?lyto the left of the keypad mnnecfor. 4- Attach the black metal mounting strap to tlhe rear of the keypad as follows (see dagram); - Face the pointed end of the mounting strap facing the keypad front. Thie will be ueed to latch onto the inside of the wall. - Place the emall white plastic spacer underneath the mounting strap. Secure the munting strap using the 5/8 inch Philhpe head ecrew (supphed) and the plastic spacer to location 1. - Secure the other end of the strap (location 2 on diagram) to the whte plaetic openirlg using the Philhps head screw removed in step 2. 5- Connect the white plastic tab into the round opening immediately behind the keypsd door. Place the longer Philtips head screw fincluded) through the opening inside the keypad door and begin to tighten the screw. Tighten the screw and leave the tab in a down poe~on. 6- Run the keypad wiring to the control panel and attach the wiring to the keypad. 7- Place the keypad into the wall opening with the side containing the black metal strap first until it graba the inside ot lhe wall. 8- After inserting the eide of the ke~rpadwfih the metal strap, insert the other side into the opening until the entire keypad is firmly in the wall. 9- Tghten the screw inserted in step 5.

XL.2 HOOKUP& INSTALLATION Page 11

KEYPAD MYOUT

XL@ORM

Model 6615 LED KeyPW

1) ZONE STATUS LEDS These LEDS dsplay the current zone statue including alarms, bypaaeee, troubles and fau~s. Each mndifion will cause these LEDS to operate dfierently as follows:
ALARMS Fast Bfink (approx. 150 ms. ON -150 ms. OFF), TROUSLES Slow Pulse (approx. 600 m6. ON -600 ms. OFF), BYPASSES Wnk(100 ms. ON -900 ms, OFF). Zone bypassea are displayed a6 a very slow wink of the zone LED light. FAULTED ZONES ~hd ON. Faulted zoneaarethe lowest,prior~intication. Fauhedburgla~ zones are displayed wth the LED sofidly ON while the system is disarmed. NORMAL OFF 2) ARM/DISARM LED This LED indicates whether the system ia currently armed (ON) or disarmed (OFF). Thie LED will also btink fast to show that alarms have omurred or bhnk slowly upon failure to mmmunicate wfih the Central Station.
XL-2 HOOKUP & INSTALLATION Page 12
3) STAY LED This LED displays whether the s)/afem has been amed in the STAY mode, ON Interior zones are bypassed OFF Interior zones are normal 4) INSTANT LED Thie LED displays whether the ey!jtem has been armed in the INSTANT mode, meaning that the system ia currently armed ati all delay zones are instant, ON Delay zones aremrrentlyinstsnf OFF Delay zones arenonwal 5) AC/LOW BATTERY LED This indicator hght @splaysthe c!Jrrenf pwer status of the panel as follows; ON AC is present OFF No AC, mnning on battery backup Slow Blink Low baftew condition detected 6) READY LED This LED displays whether the s)~etemis ready for arming. The READY hght is common to all BURGURY ZONES wtih the following indications; ON System resdy Itobe armed OFF System not ready to be armed Slow Blink Fast Bhnk Indicatea Installer programming mode Aam ltiem~ Mode
7) STAY BU~ON The STAY mode enables arming tha system, excluding zones programmed as interior zones. This will provtie exferfor protection of the location while allowing full awess throughout the interhr. 8) BYPASS BU~ON The BYPASS key is used to tem~mrarily exclude protection to a specific zone. 9) INSTANT BU~ON The INSTANT button enables arming of the eystem, eliminating the entry/exit delay. 10) CODE BU~ON The CODE button is used to enter the installer programming mode and entry of user codes.

KEYPAD SOUNDER

CHIRP Keypad emts a short chip to wnfirm each keystroke. STEADY The keyps.dwill make a steady sound during entry time, an~or during burglary alarm. CHIME - steady 1 e~lcondtone, ACKNOWLEDGE - UWn successful entry of a certain mmmands the system will emit a sound for approximately hati a second, PULSING - A pulsing sound (approximately hati a semnd ON then OFF) indicatas a trouble (nndiiion euch as AC loss, Low Battery, or Fire Zone. NEGATIVE ACKNOWLEDGMENT - UWn entry of an illegal command the keypad will amMfour short beeps. For example,, if attempfin to define a new user and the master user ie not entered, four sbrf beeps will be made Indicating tha the command was unsuccessful. ! SOUNDER RINGBl\CK - Several short beeps to indicate successful mmmuniwtion to the Central Station. This occurs for all eignals, excluding ambush and eilent zones. FAST PULSING SCIUNDER- Sound anerated during entry time period AFTER an alarm condition has occurred and the system.reached be # cutoff. A pulsing sounder will fo!low the bell oufPut on I?re condtions. Trouble condnlons also generate a pulslng eounder and will follow the loop or be silenced through entry of a viihd user code.

Reset is acmmptished through the entry of any vatid user code. This can be used to reset the smoke detectors attached to the system, silence any bells, or clear the keypad display or sounder. In addition an option exists, for mahing the q key to act as a reset for claaring the sounder, communicafiins failure, and aksmr memy. This p:sgrsmmable option can be obtained through location 3 of question 05.

BYPASS

Bypassing is performed to temporarily exclude zones which are fauky or not ready from activating the system. Depress the BYPASS button follo~fed by any vahd four(4) &gif user code, followed a number 1-6, wh~h represertfa the reepedtve zone to be bypaseed. EXAMPLE: BYPASS ZONE 2 (Aesume user code of 1234) BYPASS 12342 Subsequent bypaseee can be macle by depressing the BYPASS button followed by another zone number within a ten second perfod. After this ten aemnd period twill be necessary to enter the entire command including the user de. After a successful bypass the keypad sounder will emit the acknowledge beep, and the reepetiive zone LE13will WINK SLOWLY. In addtion the following rules for b]fpaas exist;. FIRE zones cannot be byp~ssed. 24 hour zones can be bypassed, however they CANNOT be unbypassed if they are violated. Zones can only be bypaseed while the system is disarmed, at which time visual indication will be rti~layed. o Bypasa signala are transmi~ed to the Central Station UPON ARMING if a bypaes mde has been programmed. NOTE: Zones which are bypassucl are not protected when the system is armed.

AUTO UNBYPASS

All burglary zones which are bypaaaed can be automatically unbypasaed uWn system dieam, assuming no other zone(s) hdd been in alarm. 24 hour zones w~ch have been bypassed will be unbypaeeed only if they are nomal. The auto-unbypase feature is a programmable option (see question 5 of the programming aequeme). Auto unbypsss option must be selected for all UL applications

6.10. 6.11.

MANUAL UNBYPASS USER CODE PROGRAMMING
wdea (4 dgka each) with the following apphcafions;
This function removes an existing Ioypasafrom a currently bypassed zone. The procadure is the same as b~aaa Usere wales can be entered or modified directly through the keypad. Tha system ~~~~Nuwueelr

1 MsterUsr [Default= 1234] 2 UserW ~fmlt = nufll 3 Uwr #3 [~fatit = rrtil] 4 UserW bfadt = nti] User#5 [Defatit = rndl] NO~ Canb an W 5 hbusb Cti nrUser#6 [Dsf~t = null] 6 NOTE: Only the master user (user number 1) can pwram or modfy other users.

only cti

XL-2 HOOKUP & INSTALLATION Page 15
USER DEFINITION PROCEDURE: CODE [USER] [USER#] [USERID] where: CODE [USER] [USER#] Example: Define operator W with an ID of 7493. (Assume master ueer mde ie 1234), CODE 123437493 An acknowledge sound (steady tone) verffies a sumessful user mde programming. A negative acknowledge sound (4 short tones) iq,ticetee uneucceasful programming. If additional user programming ie necessa~, repeat.the procedure listed above, User programming can be performed while the ayetem Ie DISARMED ONLY. Code butfon onkeypad Maater UserlD@de(user#l) Desired ueertobe progmmmed(l-6) O-9
[USERID] Fourdigit usercode. Vatiddgtisare
If a dialing format is programmed which transmite openin~closing by user ID, each user will report the respective ueer number. DURESS/AMBUSH If ambush capabiliy is required then an ambueh transmission code must be entered wif~n the programming sequence. When ambush hae been enabled then the user #6 code will be used as an AMBUSH rode, In this mode, entry of the user #6 wde will ARM or DISARM the syste,mand transmit the ambush code to the Central Station. Furthermore if openin~cloeing by user reWrfing is programmed, user number 6 will be reported along with the ambuah code. If ambush has not been programmed then user #6 can be used aa an ordinary user code, ARM ONLY CODE [USER 5 CODE] A programming option exiets to make user #5 an ARM only code. This means that the code can only arm the system am would be ueed for a user such as a maid or tem~ra~ ueer of the syetem. This is obtained through location 2 of question 5.

USER DELETION

Remval of ueers from the system can be performed as follows; USER DELETION PROCEDURE CODE [USER] [User #] Where: [USER] Master user mde [User #] Represents the user number being deleted. (2-6), Note: User number 1 cannot be deleted. * ie the* (asterfsk) key from the keypad.
KEYPAD AUXILIARY CONDITIONS

The eyetem has the ability to transmk four separate keypad emergency condtions as follows: # FIRE 79 AUX. 13 AMBUSH [USER CODE #6] For example, the 24 hr keypad panic can be initiated through simukaneous depression of the # and q keys. The panic rendition can be silent (no bell output) or au~ble baeed on the programming option. NOTE: The defauff value for panic is audible. In adtiffion to the keyefrokee, the XL4600SM keypad containe dedcated function keys for the auxifiary condfiions. These keye can be acfvated through eimu~aneous depression of the two keys. Audible panic can be RESET BY ENTERING ANY VALID USER CODE. The keypad FIRE and AUX renditions are selectable through the programming eequence. The ambush code will be user #6 Han ambush code is programmed in question #15. PANIC
XL-2 HOOKUP & INSTALLATION Page 16

SYSTEM PROGMMMING

The eystem can be programmed in anyone of the fol~wing met~s. Orectly through keypad (XL4600RM, XL4600SM, 8605 or 6615). EZ-MATE PC DOWNLOADER MOdel~OOremotely NOTE: The =-Mate downloader haa not been tested for UL app~cationa.
Thie manual describes system programming via the keypad. The other programming davices include documentation descrihng their programming procedures. Keypad programming is aamptished inside cover of this manual. by understating and wmplefing the PROGRAMMING SHEET bcated on the programming questions are availtile for the
There are 19 total programming questions numbered 00-18. A~tional p~rammable zone descriptors when LCD based ke~ads are used.
Wthin each question there are several locations labeled L1,L2, etc. for data entry. The system is shipped from the factory with SPECIFIC DEFAULT VALUES which were selected for a typkal installation. If the defauk values are suitable for your installation then programming can be simp~ied. Tha defauh values are listed w~h each programming question and in thtl SYSTEM DEFAULT aecfion of this manual.

PROGWMMING QUESTIONS

This secfionof the manual defines the programming questions along wfihthevaluee expecfedforeach queetbn. Completa the Programming sheet and then enter the data through the keypad as explained in the section titled Data Entry Through the Keypad.
QUESTION 01 PRIMARY TELEPHONE NUMBER

DEFAuLr2wAAAAAAAAA

Enter the telephone number finclucting area code or ~aling prefix IF NECESSARY) of the primary central atafkm receher in L1 - LI 2. Vahd diating digits are 0-!1, B=. , and C= three second pauea. An entry of the digtf A sign~es the end of the phone number. REPORTING ROUTE The system will report all signala to the primary receiver phone number. Furthermore the panel will atfemafe Nfween the primary and secondary receivers (itthf] second phone number is programmed) for a maximum of 8 attempts each in the event the signal has not been acknowledged.

PARTIAL EXTENDED The patial extended format transmtis a standard signal for alarm mn~tions and an etietied message for restores and other system mndifions, NOT&. The extended message @ales must be B-F). Example: Alarm Condtion 8531 Restore 853 E EEE 1
XL-2 HOOKUP & INSTALLATION Page 18

Quesfion04

L2RECEIVEH

TYPE DEFAULT=6

E/~~Jp
digti for the desired receiver type from the chart below in location L2. NPICAL CS RECEIVERS DESCRIPTION FBI, Ademco Slow, Silent Knight Slow 10 PPS, 1400 Hz., No Parity o= FBI 1= IO PPS,1400 HZ, Parity FBI 10 PPS,2300 HZ, No Parity 2= FBI 10 PPS, 2300 Hz, Patity 3= FBI, Silent Knight Fast, ADCOR, ADEMCO ~5 4= 20 PPS, 1400 Hz, No Iarky FBI, Radionics Slow (1400) 20 PPS, 1400 Hz, Parity 5= FBI, Franklin, Sescoa, DCI, Quickalert, Variiech, ADEMCO PPS, 2300Hz., No lParlty 6= FBI, Radionics Slow (2300) 7= 20 PPS, 2300 Hz, Padty FBI 40 PPS, 1400 Hz, No lParity 8= FBI A= 40 PPS,2300HZ, N0 Parity FBI, Radionics Fast (2300) B= 40 PPS, 2300 Hz, Pafity UL compatible receivers: FBI CPZ?O(all formats), ADEMCO W5 (all formats without panty), Silent Knight 8520,,9000.
Question04 L3-MESSAGE LEN(STH/BELL LOCKOUT Default=O
Enter the digit for the desired message length from the chart below in location L3. 0= 3x1 3dlgltaccount,l dlgltevant cola, no belllockout 8=3x1, wits bell hkout A = 4x1, wkh ball kkouf 2= 4Xdigi, account number, 1 digit event code, no bell lockout 4 x &gii account number, 2 digfi event code, no bell lockout E = 4x2, wfih ball bckoti 8= If bell lockout is selected then subsequent activations of the same zone within the same arming intewal will wt acfiva!a the bell. This applies only to burglay (non 24 hour) zones. For UL installations bell lockout must not be sele(Xed.NOTE Please consult your Central Station manager to determine the formats and message lengths which are acce~ed by the receiver. To select European diating format, add 1 to the value selected for this digit, NOTE: European dia~ng format has Mt been tesied by UL.
Question 04 L4- SYSTEM OPTIOIVS Defau/t = 1
Enter the digit for the desired system options from the chati below in location L4. o= Silent Keypa(~Panic 1= Audlbla Keypad PanlC 2= Silent Keypacl Panic, Split Repo~ng Audible Keypad Panic, Sptit Repofling 3= 4= Silent Keypacl Panic, 24 Hr Test 5= Audible Keypad Panic, 24 Hr Teet 8= Silent Keypacl Panic, Sptit Reporting, 24 Hr Test 7= Audible Keypad Panic, Sp~t Reporting, 24 hr Test 8= Silent Keypacl Panic, Bell Test Audible Keypad Panic, Bell Test 9= A= Silent Keypac~Panic, Split Reprfing, Bell Test B= Audible Keypad Panic, Sp~i Reporting, Bell Test c= Silent Keypacj Panic, 24 Hr Test, Bell Test D= Audible Keypad Panic, 24 hr Test, Bell Teel E= Silent Keypa(~Panic, Sptit Reporting, 24 Hr Teet, Bell Test -. Audible Kevc,ad Panic. SDlit Remrtino, 24 Hr Teat, Bell Test F= DESCRIPTION OF SYSTEM OPTIONS Keypad Silant/Audible Panic - Determines whether the keypad panic condition ( q & #from the keypad) will activate ttie bell. In either case a eignal will be transmitted to the Central Station if a panic code has been programmed. NOTE: The keypad panic rendition can be activated through location 1 of question 05. Spiff Reporting -The split repoffing option will direct all opening and closing signals to the seconda~ rewivertelaphorse number. All other conditions (alarms, froublea, restores etc.) will adhere to the reporting route described in question 01.If ep~t roWrfing ie selected then the second:~ry receiver telephone number MUST be programmed. 24 Hour Taaf - If 24 hour test is enabled then the systam will transmit the test mde to the Central Station every 24 hours in the absance of any other signal. Transmission of any signal will reset the 24 hour test clock. For example f a business opened and closed 6 days a week then a teat signal will be generated 24 hours after the laSt closing sgnal. NOTE Tma option is required for UL Commercial Burgla~ apphcations. Ball Teat If this option is sele!ctedthe bell will be activated for one second upon successful arming. This o~on is required for UL Commercial Burgla~ applications.

XL.2 HOOKUP& INSTALLATION Paga 19

QU~TION

05 KEYPAD CONDITIONS

DEFAULT

= 1400

DEFAULT= 1

This question contains four locations for various keypad definable options Question 05 L 1- KEYPAD EMERGENCY CONDITIONS
Thie location epecifies which of the keypad emergency condifione are active. To determine the value for this hatbn the values for the desired conditions as ehown in the chart below +1 +Keypad Panic (.& #) Enable Keypad Fire (7& 9) Enable Keypad Aux (1 &3) Enable
4 Keypad Aux = Audible For example, if you wanted the keypad panic and fire conditions only then add +1 and +2, and enter a 3 info this bcafion. The vahd selections for this digit are shown below; O = Keypad Emergency con~~ons Disabled 1 u Keypad Panic 2 = Keypad Fire 3 = Keypad Panic, Keypad Hre 4 = Keypad AUX (slent) 5 = Keypad Panic, Aux (Silent) 6 = Keypad Fire, Aux, (Silent) 7 = Keypad Panic, Rre, Aux (Slent) C = Keypad Aux, (Audible) D = Keypad Panic, Aux. (Audible) E = Keypad fire, Aux, (Audible) F = Keypad Panic, Fire, Aux (Audible)
Question 05 L2 - MISC OPTIONS DEFAULT= 4
To obtain the value for this location add the values corres~nding
to the desired optione or consuk the table:
PANIC or KEYSWITCH (tl ) This option determines whether connections 10 & 13 on the control panel will be used ae a panic input or a keyswitch input. Note : Add 1 if a keyewkch is desired, HARDWIRED PANIC SILENT or AUDIBLE (+2) Determines whether the hardwired panic circuit will be audible or silent. NOTE: Add 2 if audible. AUTGUNBYPASS ENABLE (+4) Determines whether zones will automatically be unbypaesed upon disarm. Add 4 for autounbypaas enable. ARM ONLY COOE [USER ~] (+8) If user number 5 should be used as an arm only code (maid code) then add 6 to ttis digit, The vatid selections for this digit are shown below: O= Panic Input Silent 1 = Keyswitch Input 2 = Panic Input Enabled Audible 4 u Panic Input Silent, Auto.unbypaaa 5 = KeySwitch Input, Auto-unbypass 6 = Panic Input Audble, Auto-unbypass 8 = Panic Input Silent, Arm Only User = Keyswitch Input, Arm Only User 5 A = Panic Input Audible, Arm Only User 5 C = Panic Input Silent, Auto-unbypass, Arm Only User 5 D = Keyswitch Input, Auto-u nbypass, Arm Only User 5 E = Panic Input Audible, Auto-unbypase, Arm Only User 5

Question08 L1 -ENTRY DELAY Defauff = 2
Enterthe desired antrydelaytime in 15 second increments. The vatid range of input is 1- F, wfih 1 indbsting a 15 second entry delay and F indicating 225 seconds. For UL app~cations the maximum entrance delay shall not exceed &5 seconds for buaehold applications or 15 sewndls for commercial burglary applications.
Quest;on08 L2 -EXITDELAY Defauff = 4
Enter the desired exfi time in 15 !second increments. For UL appticstions the maximum exh delay shall not exceed 69 second$.The vatidrange ofinputisl -F, withl indicating a15semnd exfidelay and Finticating 225aeoOrfd$.
Question08 L3-WURGLARYWf:LL CUTOFF DefauM = 5
Enter the desired bell cutoff time cln alarm condtiona for burglary and panic in 3 minute intervals. The va~i range of in~ isl -F, w*h FindtMting aninfinite bum ball cutoff.Exampls 3=9minutes. For ULinstallationa inmmmercialm~m~Ona the minimum bell cutoff shall be 15 minutes, or 4 minutes for household burgla~ appticatiins.
@cation 08 L4 - FIRE WELL CUTOFF Defauff = F
Enter the deeired bell cutoff time for fire mndtions in three minute intewals. The vahd range of input is 1- F, wkh F itiiceting an infinite fire bell cutoff. Example 3 = 9 minutes. For UL installations the minimum fire bell cutoff time shall h 4 minutes. XL-2 HOOKUP & INSTALLATION Pags 21
tiesfiins 09-14 represenf all the options related to programmable zones 1-6. Each question contains four(4) bcefbns L1-L4. The firet two locations (Ll -L2) define the zone type. The sewndtwo locations (L3-L4) define the slam codetransmiffsd to the Central Sfatbn for that zone. ZONE TYPES Zones l-6canbepmgrammed foranyone of!hefollowing zone~pes:

8.1. ~

This is the induaf~ standati exiVentry zone. When the system is amsd exfi time begins. After exit expiree, any subsequent violafiin of this zone will ~n entV time. If the system is not disarmed within the p~rammed entry time an alarm will occur. The keypad sounder will annunciate steadi~durfng entry fima, unless there had been an alarm condiibn, at which time if will wise. Delay zones will activate instamly when the sysem is armed using the INSTANT mode.

L3 - L4

ZONE ALARM CODE

QUESTION 10 ZONE 2

There are 4 locations (Ll -L4) within this question w~ch define the operation of zone 2. Enter a 2 digit number in bcafions LI and L2 from the chati above that represents the desired type forthia zone. Enter the desired alarm code in locations L3 and L4 for tftia zone relative to the dialer format selected.

40 INTERIOR FOLLOWER 32

QUESTION 11 ZONE 3
There are 4 locations (L1-L4) within this question which define the operation of zone 3. Enter a 2 digit number in locations LI and L2 from the chafl above that represents the desired type for t~s zone. Enter the desired alarm code in Iocationa L3 and L4 for this zone relative to the dialer format selected.
ZONE TYPE ZONE ALARM CODE
XL-2 HOOKUP & INSTALLATION Page 24

QUESTION 12 ZONE 4

There are 4 locations (LI-L4) within this question which define the operation of zone 4. Enter a 2 digit number in locations LI and L2 from the charf above that represents the desired type for this zone. Enter the deeired alarm mde in lo~:ationsL3 and L4 for this zone relative to the dialer format selected.
L1 - L2 L3 - L4 QUESTION 13 ZONE 5
There are 4 locations (LI-L4) wkhin this question which define the operation of zone 5. Enter a 2 digit number in locations L1 and L2 from the chati above that repreeenfe the desired type for this zona. Enter the desired alarm mde in Iol;afions L3 and L4 for this zone relative to the dialer for~t

~~ eelecfed.

LI - L2 ZONE ~PE: 10 L3 - L4 ZONE ALAF{M CODE 35

GtUESTION14 ZONE 6

There are 4 locations (L1-L4) wkhn this question which define the operatbn of zone 6. Enter a 2 digit number in bcations LI and L2 from the zone chart that represents the desired type for thie zone, Enter the desired alarm code in Io,:afions L3 and L4 for this zone relative to the dialer format selected. LOCATIONS L1 - L2 L3 - L4 ZONE TYPE ZONE ALARM CODE DEFAULTS FIRE
QUESTION 15 AMBUSH/AC LOSS
There are 4 locations L1-L4 in this question. LI - L2 is the alarm mde that will be transmitted on AMBUSH. M - L4 is the P,CLOSS CODE, The same rules for programming regarding dialer format apply here. If ether, or both of these transmis!$ions are not desired, program their reepecfive Iocationa AA AMBUSH transmissions are immediate and not aborfable. AC LOSS transmissions will be reported 15 minutes after detecfiin.

LI - L2 L3 - L4

L1 L2 L3 L4

BYPASS RESTORE TROUBLE #OF RINGS

A A F 8

QUESTION 19 KEYPAD FIRU KEYPAD AUX. DEFAULT: AAAA
There are 4 Iocafiins LI-L4 in this question. Lt - L2 ia the slam mdethat will betransmiffed upon acftiafionof the ke~ad fire mndifion (pressing the 7 & 9 keys on the keypad). This code can vary from any of the zones whch are programmed as tire. L3 - L4 is the mde transmitted to the CS for ke~ad aux. mndfiion ( 1 & 3 from the keypad) NOTE: These keypad eme~ency mndtions are optional and can be enabled wti~n question 05 of the programming aequenca. If ekher or bth of these transmissions are not desired, program their raspecfive Iocatbns AA.
LI - L2 L3-L4 Question 00 INSTALLER

KPAD FIRE KPAD AUX CODE

There are 4 locations L1 - L4 in thb question. Enter any 4 tigif (O-9installer mde desired, This mde is used to ENTER the system programming tie via the keypad. Typically each installing mmpany would uae a unique installer tie in order to preve~ unaUthOti@ people from gaining access to their panels. Note: The factory defauh value for the installer mde is 4800 in bcations LI -L4 respscfiiely.
XL-2 HOOKUP & lNSTALLATfON Page 26
DATA ENTRY VIA LED BASED KEYPADS
This section describes the physical keystrokes necessa~ to perform keypad programming and how to infe~ret the data displayed on the LED based keypads (XL4600RM, XL4600SM or 661 5) during programming operations.
Adual keypad programming ahoulld be peflormed after @mplefion of the programming sheet.
NOTE: For information regarding programming through the LCD based keypads mneuk the nex sacfiin of ttis manual.
HOW TO ENTER PROGRAMMING MODE The SYSTEM programming modt~can be entered WHILE DISARMED ONLY as follows DEPRESS the COCIEbutton. DEPRESS the * b!)tton, (asterisk) ENTER the four digil, INSTALLER CODE (default= 4600)
WHAT YOU SEE ON THE KEYPAD PROGRAM MODE u READY LEIO:
Upon entering the installer keypa(~programming mode the READY LED will slowly pulse, and will continue to pulse until I(?avingthis mode. The remaining LEDS display the t~uestion number and location contents as indcated below

OUESnON MUMER

.!0!.2::

. :. :

WESTON NUMBER

SS15Key~d Progmmming

XL-2 HOOKUP & INSTALLATION Page 27
QUESTION NUMBERS Zone LEDSl followe: EWMPLES:
ZONE LEDS: the Wnent QUESTION NUMBER (not thespecfic location witMneach question) aa
As previously stated there are 17 total questions, each of which mnfains mutiple data entry Iocafiona. thmugh5display
In the diagram shown the question number is obtained by ADDING the values of all LEDS that are ON. Zonel ON, Zonas2-50FF Zone 1 ON, Zone 2 ON, Zones 3-5 OFF Zone 2 ON, Zone 3 ON, Zone 4 ON, Zones 1 and 5 OFF LOCATION CONTENTS = SYSTEM STATUS LEDS
display the DATA that resides in EACH location within the The remaining status LEDS (ARM,STAY,lNSTANT,AC/LB) current question. As per the dagram and explanation above, the value located next to each LED must be ADDED to ~lculate the total data, for each bcafion.

00 Installer Code 01 Phone #Phone W 03 Callback Number 04 Dialer Options 05 Kpad options 06 Account #Aaunt W 06 Timaouts 09 Zone #Zone w 11 Zone W 12 Zone #Zone #Zone W 15 System Codes 16 System Codes 17 System Codes 18 System Codes 19 System codes 21 Zone 22 Zone 23 Zone 24 Zone 25 Zone 26 Zone 1 Descriptor 2 Descriptor 3 Descriptor 4 Descriptor 5 Descriptor 6 Descriptor 1234 (null) (null) (null) (null) (null)
4600 234~ ~ (none) ~ (none) Touch Tone, 20PPS, 2300hz, 3x1, Au~bla Panic Keypad panic & Auto unbypass enabled 1234 AAAA (null) Entry Delay =30 sec., Exit Delay =60 seconds Burg Bell Cutoft = 15 minutes, Rre Bell Cutoff= No Timeout Delay (20) Code =31 Inferior (40) Code =32 Perimeter (1O) Code =33 Perimeter (1O) Code =34 Peflmeter (1O) Code =35 Hre (84) Code= 16 Ambush = AA (null) AC Loss= W (null) Panic =22 Low Batte~ = AA (null) Open = A (null) Close= A (Null) Test Code= AA (null) Bypass = A (null) Restore= E Trouble= F Keypad fire = M (null) Keypad Aux = AA (null) ZONE ZONE ZONE ZONE ZONE ZONE (LCD (LCD (LCD (LCD (LCD (LCD Keypads Keypads Keypads Keypads Keypade Keypads Only) Only) Only) Only) Only) Only)

USER CODES ; 5 6

XL-2 HOOKUP & INSTALLATION Paga 32
\MARN!NG LIMITATIONS OF THIS ,ALARM SYSTEM \Nhilethissys!em is an advanceddasi{~n securiiysyetem, kdoesnot offer guaranteedprtietiion againatburglaV, fire ortiher emergency.Any alarmsystem,whethercommercialor rasidantial,is subjeti to compromiseor failureto warnfor a varietyof reasons. For example:. lntrudarsmaygain amessthrough unprotetiedo~ninga orhavathatwhnical aopMtiicationto bypawanalarmsenwr or disconnectan alarmwarningdevice.
. intrusion dat&ors (a.g., paasivf~infrarsd datatiors), smoke datetiors, andmanyothar senaing devi~awill~twti wkhoti ~wer. Battery oprated dsvices will not work without batteries, with dead batteries or if the batteries are not put in properly. Devices pwerd solaly by AC will not work if thair AC powar su~ly is cut off for any reawn, however &lefly. Wgnalsaent bywiralaas transmMers may be blo&edorrefleded bymetal beforathey reach thealarm rmiver. Eventi the signal path has baen racsnt!ly checkad during a weekly test, blockage can oaur t a matal object is movd itio the path, Ausermay not beableto reackla panic orsmergancy bunonqubklyanough.
While smokadatatiors have pla,y&a keyrole inreducing residential firadeaths inthe Untied States, th~maynti activata or provide early warnirq~for a variety of reasons in as many aa 354 of all firas, according to data pub~shed by the Federal Emargancy Managomant Agency. Soma of tha raaaons amoka detactors used in conjunctbn wfih this System may not wok ara as follows: Smoke detectors may have been improperly installed and pmtionad. SmMe detmore may not sense firaa that start whare smoka cannot reach the datactors, such as in chimneys, in walls, or roofs, or on the other side of closed doors, Smoke dstecfors may not sense a firs on anothar Iaval of a raaidanrn or building. A second floor detetior, for axample, may not $~ense first floor or baaemeti fire. Moreovar, smoke detactors hava aenaing fimifsfrnrrs. a No smoke detector can aenae every kind of firs avey time. In ganaral, dstecfors may not alwaya warn ebo~ fires ceueed by mralessnesa and safaty h=ards Ike smoking in bed, violent explosions, escaping gee, improper storage of flamm~le matatiab, overloaded elactfical circuits, children playing with matchas, or arson. Depanding on the nature of the fire andlor the Imation of the smokel datactore, the detactor, avan ti it operataa as anticiptiad, may not provide sufficient warning to allow all occupants to escapa in time to prevant injury or daath. Passive infrared Motion Date&c,fficanonly detetiintrusion wfihinthe design& rangeeas tiagram& intheirinatallatbn manual. Passive Infrared Detmora do not provide mlumatric area protection. They do create mutiple baams of protection, and intrusion can only be datected in unobstructed areas rnvered by tha baams, Thay cannd detacf mdion or intrusion that takes place ba~nd walia, ceitings, floors, closed doors, glaaa paRitions, glass dmrs, or window. Machankl tam~ring, masking, painting, or spraying of any matedal on the mirroffi, windows or any Prt of the opt~ system an raduce their datection abitify, Pe~ssiva Infrared Detectors sense changes in tampraturw howevar, as tha ambient temperature of the protacted ama approaches the tempertiura ranga of 90 to 150F, the datection performance wn dacreasa, Alarm warning davices such assirens, bells orhorns maynotalefi other side ofcloaed orpatily open doors, bwarning deviwasound paoplaor wake upslaepars whoarel=at& onthe onadifferent levalof thareSidenW fromthe bedrooms, then they are lees likely to waken or aleti people inside the bedrooms. Even persons wh are awake may not haar the warning if the alarm is muffled by noise from a stereo, radio, air condtiioner or other a~liancas, or by paasing traffic, Finally, alarm worning devices, howaver loud, may not warn haaringimpaired people or w~en deep sleapars. Telephone hnesneeded totransmk alarm signals from apramises toacentral monkoring tiation may beoutofsewbeor temporarily out of service. Telef)hone tines are also subject to compromise by sophisticated intruders. Even ifthesystem raspndsto theemergency asintended, however, mcupants mayhave insuMcient timetoprotti themaelvea from the emergenc~fstiuation. In the case of a monitorad alarm systam, authorities may not resWnd appropriately. TKsequipment, tikeother eletiflml devicas, issubjetito mmpnantfailura. last as long as 10 yaars, the electronic wmponants muld fail at any time. Evanthough thiaequipmant iades@ndti

FEDERAL COMMUNICAmONS COMMISSION(FCC)STATEMEN~ ~s equipmenthasbeantased to FCCrequirements andhasbeenfoundacceptable use.The FCC requires the folbwing statement for
for your information. This equipmant generates and usas radio frequency anargy and f not installsd and ussd properly, that is in strisf amrdance wfih the manufacturers instructions may cause interference to radio and television reception. k has been tested and found to mmp~ with the timifs of Pan 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential insallatbn. However, there is no guarantee that interference will not =ur in a particular installation, Hthis equipment does not cause interfere to radm or television reception, whiah can be determined by turning the equipment off and on, the user is encouraged to try to correct the interferewe by one or more of the following measures:lf using an indoor antenna, have a qua~tiyoutdoor antenna installed. Reorient the remiving antenna until interference is reduced or eliminated, Move the radio or television r~eivar away from tha mntroV mmmunicator. Move tha antenna leads away from any wire runs to the sontrollmmmunicator. Plug the mnfroVcommunicator into a different outlet so that it and the radio or television receiver are on different bra~h circuits.
H rrscsssary, the user should consult ths dealsr or an expsriencsd radiofielevision technician for additional suggesfbns. The user may find the following hoklet prapared by the Federal Communications Commission helpfuh Intarferance HandkoW This booklet is available from the U.S. Government Printing Office, Washington, DC 20402. Stwk No. 004000-00~-7. The user shall not make any changes or mod fi~tions to the equipment unless authorized by the installtiion Indrutiions or User,s Manual. Unsuthorizsd chsnges or modifications muld void the use?s authorii to operate the equipment, IN THE EVENT OF TELEPHONE OPERAnONAL PROBLEMS
In the event of telephone operational problems, disconnsaf the mmmunicator by ramoving the plug from the RJ31x jask. Do not dscennect the phone connation inside the wmmunicator. Doing so will resuk in the loss of lhe phone works mrrecfly after the mmmunicator has been &swnne&ed from the phone Nnas,tha mmmunicator has a problem and should be rstumed for repair. K upon dismnneding the communicator, there is still a problem on your fine, notify the talaphone sompany that they have a problem and rsquest prompt repair service. The usar may not under any circumstances on or out of warranty) anempt any service or repairs on the system. It must be returned to the faofory or an authorizd sewice agen~ for all repairs.
XL-2 HOOKUP & INSTALLATION

Page S8