Article 17

Using this Equipment in Japan
In Japan, the frequency bandwidth of 2,400 MHz to 2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station). 1. Sticker Please put the following sticker on devices incorporating this product.
The frequency bandwidth of this equipment may operate within the same range as industrial devices, scientific devices, medical devices, microwave ovens, licensed radio stations and non-licensed specified low-power radio stations for mobile object identification systems (RFID) used in factory product lines (Other Radio Stations). 1. Before using this equipment, ensure that it does not interfere with any of the equipment listed above. 2. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. 3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations.
2. Indication The indication shown below appears on this equipment.

(1) (2) (3)

2.4DSOF4
2.4: This equipment uses a frequency of 2.4 GHz. DS: This equipment uses DS-SS modulation. OF: This equipment uses OFDM modulation. The interference range of this equipment is less than 40m. This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is possible to avoid the band of mobile object identification systems.
3. TOSHIBA Direct PC Monday Friday: 10:00 17:00 Toll Free Tel: 0120-15-1048 Direct Dial: 03-3457-4850 Fax: 03-3457-4868

Device Authorization

This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business Law of Japan. The Name of the radio equipment: refer to the equipment label provided on the computer JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENT Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017 The following restrictions apply:
Do not disassemble or modify the device. Do not install the embedded wireless module into other device. 5.17 GHz to 5.23 GHz for indoor use only.
Radio Approvals for Wireless Devices
The following information is dependent on what type of wireless device is in your computer. Not all devices are available on all models.
Approved Countries/Regions for use for the Atheros AR5BMB-43/44 and AR5BMB5 Mini PCI Wireless Network Adapters
This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.

Approved Countries/Regions for use (Bluetooth wireless technology)
Bluetooth Card from Toshiba equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Argentina Belgium Chile Czech Republic Estonia Germany Hungary Italy Korea Lebanon Luxembourg New Zealand Peru Portugal Slovenia Switzerland Uruguay Australia Bulgaria China Denmark Finland Greece Iceland Japan Kuwait Liechtenstein Malta Norway Philippines Singapore Spain Thailand USA Austria Canada Cyprus Egypt France Hong Kong Ireland Jordan Latvia Lithuania Netherlands Oman Poland Slovakia Sweden UK Venezuela
Bluetooth Wireless Technology and Your Health
The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is much less than the electromagnetic energy emitted by wireless devices such as mobile phones. Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:
Using the equipment with Bluetooth wireless technology on board airplanes, or In any other environment where the risk of interference to other devices or services is perceived or identified as harmful.
If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the device with Bluetooth wireless technology prior to turning on the equipment. Exposure to Radio Frequency Radiation The radiated output power of the Bluetooth Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.

Notice

The information contained in this manual, including but not limited to any product specifications, is subject to change without notice. TOSHIBA CORPORATION AND TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (TOSHIBA) PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING. TOSHIBA ASSUMES NO LIABILITY FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN OR FOR DISCREPANCIES BETWEEN THE PRODUCT AND THE MANUAL. IN NO EVENT SHALL TOSHIBA BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, OR EXEMPLARY DAMAGES, WHETHER BASED ON TORT, CONTRACT OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF.

Trademarks

Satellite and ConfigFree are registered trademarks of Toshiba America Information Systems, Inc. and/or Toshiba Corporation. Microsoft, Outlook, Windows, and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. DirectX, Active Desktop, DirectShow, and Windows Media are registered trademarks of Microsoft Corporation. Wi-Fi is a registered trademark of the Wi-Fi Alliance. Intel, Intel Core, Celeron, Centrino and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. TouchPad is a trademark of Synaptics, Inc. Adobe and Photoshop are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. ExpressCard is a registered trademark of PCMCIA. Memory Stick, Memory Stick PRO, and i.LINK are trademarks or registered trademarks of Sony Corporation. Secure Digital and SD are trademarks of SD Card Association. MultiMediaCard and MMC are trademarks of MultiMediaCard Association. xD-Picture Card is a trademark of Fuji Photo Film, Co., Ltd. Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Toshiba is under license. Other trademarks and trade names are those of their respective owners. All other brand and product names are trademarks or registered trademarks of their respective companies.

ConfigFree...150 Getting Started..150 ConfigFree Utilities..151
Chapter 6: If Something Goes Wrong.154
Problems that are easy to fix..154 Problems when you turn on the computer.155 The Windows operating system is not working.158 Using Startup options to fix problems.158 Internet problems..159 The Windows operating system can help you..160 Resolving a hardware conflict.160 A plan of action..160 Fixing a problem with Device Manager.161 Memory problems..162 Power and the batteries..163 Keyboard problems...164 Display problems..165 Disk drive problems..167 Optical drive problems.168 Sound system problems..169 ExpressCard problems..170 Printer problems..172 Modem problems..172 Wireless networking problems.173 DVD operating problems..176 Develop good computing habits..177 Data and system configuration backup in the Windows operating system.178 If you need further assistance.182 Before you contact Toshiba..182 Contacting Toshiba...183 Other Toshiba Internet Web sites.183 Toshibas worldwide offices..184
Appendix A: Hot Keys/TOSHIBA Cards.. 186
Hot Key Cards..186 Using the Hot Key Cards..187 Application Cards..188 Using the Application Cards..189 Card Case...189 Hot key functions..190 Volume Mute..190 Lock (Instant security).191 Power plan...192 Sleep mode...193 Hibernation mode..194 Output (Display switch)..195 Display brightness..196 Disabling or enabling wireless devices.197 Disabling or enabling the TouchPad.198 Zoom (Display resolution)..199 Keyboard hot key functions..200
Appendix B: Power Cord/Cable Connectors. 201 Glossary... 202 Index... 216

Introduction

Welcome to the world of powerful, portable, multimedia computing. With your Toshiba notebook computer, your work and entertainment can accompany you wherever you go. Your Computer model may be ENERGY STAR compliant. If the model you purchased is compliant, it is labeled with the ENERGY STAR logo on the computer and the following information applies. Toshiba is a partner in the Environmental Protection Agencys (EPA) ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency. Your computer ships with the power management options preset to a configuration that will provide the most stable operating environment and optimum system performance for both AC power and battery modes. To conserve energy, your computer is set to enter the low-power Sleep mode which shuts down the system and display within 15 minutes of inactivity in AC power mode. We recommend that you leave this and other energy saving features active, so that your computer will operate at its maximum energy efficiency. You can wake the computer from Sleep mode by pressing the power button. See the Mobile Computing section of the Toshiba Users Guide for more information on using power management settings to conserve computer energy.

Setting up your computer

Important information on your computers cooling fan
Your computer may have a CPU cooling fan that cools the CPU by drawing outside air into the computer. Always make sure your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your computer is in Sleep mode). In this condition, observe the following: Never cover your computer or AC adaptor with any object. Never place your computer or AC adaptor near a heat source, such as an electric blanket or heater. Never cover or block the air vents, including those located at the base of the computer. Always operate your computer on a hard flat surface. Using your computer on a carpet or other soft material can block the vents located at the base of the computer. Overheating your computer or AC adaptor could cause system failure, computer or AC adaptor damage or a fire, possibly resulting in serious injury. Read the Provide adequate ventilation section in the Instruction Manual for Safety and Comfort that is shipped with your computer.
The cooling fan location will vary depending on the computer.
TECHNICAL NOTE: You must complete all setup steps up to and including Setting up your software on page 43 before adding external or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and ExpressCards. Your computer contains a rechargeable main battery that needs to be charged before you can use it. To use external power or to charge the battery you must attach the AC adaptor. See Connecting to a power source on page 45.
Please handle your computer carefully to avoid scratching or damaging the surface.

Setting up your software

When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely.
The names of windows displayed, and the order in which windows appear, may vary according to your software setup choices.
The first time you turn on your computer, the Setup Wizard guides you through steps to set up your software. 7 From the Welcome screen click Next to enter the Setup Wizard. Confirm acceptance of Microsofts End User License Agreement and click Next. Enter your desired user name and password, choose a picture to be associated with your user account, and then click Next. Enter the computer name and choose your background and then click Next. Click the appropriate option from the Help Protect Windows Automatically screen. Follow the remaining screen prompts to complete the setup process. Click Start when the Thank You message appears. The Windows operating system checks the systems performance, and then may restart your computer.

Make sure the disc is completely on the spindle and is lying flat on the tray. If you insert the disc incorrectly, it may jam the drive. If this happens, contact Toshiba support for assistance. 9 Push the disc tray in by pressing gently on the center of the tray until it clicks into place. You are ready to use the disc.

Playing an audio CD

Insert an audio CD and close the disc tray. If the computer is turned on, Windows Media Player opens. You can use the Windows Media Player program to control the CD. To access the Windows Media Player, you can open it through the Start menu.
When using Windows Media Player, your system may not be able to activate Sleep or Hibernation modes. To prevent this from occurring, close Windows Media Player before you select Sleep or Hibernation mode.

Stop button

Play/Pause button
(Sample Image) Windows Media Player screen
The Windows Media Player control panel works much like an ordinary compact disc player: To play the CD or to pause, click the Play/Pause button. To stop the CD, click the Stop button. Before putting on headphones to listen, turn the volume down. Do not set the volume too high when using headphones. Continuous exposure to loud sound can harm your hearing.

Playing optical media

If you insert an optical disc into the optical drive and the Auto-Run feature does not automatically start your disc, try launching the optical disc manually. To do this, follow these steps: Click Start, and then Computer. Click the optical drive icon. The disc drive will run the optical disc. If your disc does not run using this method, try using an application that is associated with the media on the disc. For example, if it is a music CD, open Windows Media Player and use it to select and then play the CD. For other types of media, use the associated software to open the files on the disc.

Recording optical media

Depending on the configuration, your computer may come with an optical drive that allows you to: Play pre-recorded and recorded optical media. Read/write data and multi-media files to recordable optical media.
For more information regarding supported optical media formats please refer to your computers detailed specifications at pcsupport.toshiba.com.
Due to manufacturing and quality variations in third party optical media (e.g., CD or DVD) or optical media players/recorders, in certain cases, your Toshiba optical drive may not record on certain optical media that bear the applicable logo, or play back optical media recorded by other computers or optical media recorders. Additionally, certain optical media recorded on your optical drive may not play back or operate properly on other computers or optical media players. These problems are not due to any defect in your Toshiba computer or optical drive. Please refer to your computer's product specification for listing of specific format compatibilities. Copy protection technology may also prevent or limit recording or viewing of certain optical media. For details on how to use the software, please refer to the respective Online Help menus.

Taking care of your battery
6 Turn the computer right side up.
Reconnect any cables that were removed in step 3 of Removing the battery from the computer on page 104. Restart the computer.
The following sections offer tips on how to take care of your battery and prolong its life.

Safety precautions

If the battery pack produces an odor, overheats or changes color or shape while it is being used or charged, turn off the computers power immediately and disconnect the power cord/cable from the power socket. Carefully remove the battery pack from the computer. Do not try to disassemble a battery pack. Do not overcharge or reverse charge a battery. Overcharging will shorten its life, and reverse charging could damage it. Avoid touching the metal terminals of the battery with another metal object. Short-circuiting the battery can cause it to overheat and may cause damage to the battery or the computer. Do not incinerate a spent battery, as this could cause it to explode and release caustic liquid. If a battery is leaking or damaged, replace it immediately. Use protective gloves when handling a damaged battery. To replace the main battery, use an identical battery that you can purchase through the Toshiba Web site at accessories.toshiba.com. A reverse polarity condition should be avoided with all batteries. The main battery is designed so that it cannot be installed in reverse polarity. Charge the battery only in the computer or in a battery charger designated as an approved option. When you install the battery pack, you should hear a click when it is seated properly. Do not expose the battery pack to fire. The battery pack could explode.

Maintaining your battery

Fully discharging your battery pack will allow better accuracy of the battery meter. To fully discharge your battery pack: Periodically, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below: 3 Turn off the computers power. Disconnect the AC adaptor and turn on the computers power. If it does not turn on, go to step 4. Operate the computer on battery power for five minutes. If the battery pack has at least five minutes of operating time, continue operating until the battery pack is fully discharged. If the battery light flashes or there is some other warning to indicate a low battery, go to step 4. Connect the AC adaptor to the computer and the power cord/cable to a power outlet. The DC-IN or AC powerlight should glow white, and the battery light should glow amber to indicate that the battery pack is being charged. If the DC-IN or AC power-light indicator does not glow, power is not being supplied. Check the connections for the AC adaptor and power cord/cable. Charge the battery pack until the battery light glows white.

If you have extra battery packs, rotate their use. If you will not be using the system for an extended period, more than one month, remove the battery pack. If you are not going to use the computer for more than eight hours, disconnect the AC adaptor. Store spare battery packs in a cool dry place out of direct sunlight.
Disposing of used batteries
The life of a battery pack depends on usage. When the battery pack needs replacing, the main battery light flashes amber shortly after you have fully recharged the battery. You must discard a battery if it becomes damaged. Never attempt to dispose of a battery pack by burning or by throwing it into a fire, and never allow exposure to a heating apparatus (e.g., microwave oven). Heat can cause a battery pack to explode and/or release caustic liquid, both which may possibly cause serious injury. Always dispose of used battery packs in compliance with all applicable laws and regulations. Put insulating tape, such as cellophane tape, on the electrode during transportation to avoid a possible short circuit, fire or electric shock. Failure to do so could possibly result in serious injury.
Always use the battery pack supplied as an accessory or an equivalent battery pack specified in the User's Manual. Other battery packs have different voltage and terminal polarities. Use of nonconforming battery packs could generate smoke or cause fire or rupture, possibly resulting in serious injury. After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them. Under certain applicable laws and regulations, it may be illegal to dispose of old batteries by placing them in the trash. Please be kind to our shared environment. Check with your local government authority for details regarding where to recycle old batteries or how to dispose of them properly. If you cannot find the information you need elsewhere, call Toshiba at: (800) 457-7777. As part of Toshibas commitment to preserving the environment, Toshiba supports various trade-in and recycling programs. Visit www.ToshibaDirect.com and select Recycling & Trade-in Programs, or enter Recycle in the search bar. Toshiba is dedicated to preserving the environment by sponsoring Call2Recycle, a program of the Rechargeable Battery Recycling Corporation. For more information and for drop-off locations, visit www.rbrc.org or call 1-800-822-8837.

Traveling tips

The USB Sleep and Charge function only works for compatible ports. When USB Sleep and Charge function is Enabled, USB bus power (DC 5V) will be supplied to compatible ports even when the power of the computer is turned OFF. USB bus power (DC 5V) is similarly supplied to the external devices which are connected to the compatible ports. However, some external devices cannot be charged solely by supplying USB bus power (DC 5V). As for the specifications of the external devices, please contact the device manufacturer or check the specifications of the external devices thoroughly before use. Using the USB Sleep and Charge function to charge external devices will take longer than charging the devices with their own chargers. If external devices are connected to compatible ports when the AC adaptor is not connected to the computer, the battery of the computer will be depleted even when the power of the computer is turned OFF. As such, we recommend that you connect the AC adaptor to the computer when using the USB Sleep and Charge function. External devices connected to the USB bus power (DC 5V) function that interfaces with the power ON/OFF of the computer may always be in an operational state.
Metal paper clips or hair pins/clips will generate heat if they come into contact with USB ports. Do not allow USB ports to come into contact with metal products, for example when carrying the computer in your bag. USB Sleep and Charge function SettingsThe default setting is Disabled. Changing the setting to Enabled enables the use of this function. To change the setting, launch TOSHIBA Hardware Setup and click on the USB tab. There are two modes, Mode-1 and Mode-2 in Enabled. For normal use, set the setting to Mode-1.

TOSHIBA Zooming Utility

If the function does not work with Mode-1 setting, change it to Mode-2. Some external devices may not be able to use this function in either mode. When this happens, change the setting to Disabled. Setting item: Enabled (Mode-1) -- Enables the function Enabled (Mode-2) -- Enables the function Disabled (Default) -- Disables the function USB Wakeup functionThis function restores the computer from Sleep Mode depending on the external devices connected to the USB ports.
USB Wakeup function will supply USB bus power (DC 5V) to all USB ports, including compatible ports, even when the computer is in Sleep Mode. USB bus power (DC 5V) will not be supplied if the computer is in Hibernation Mode or shutdown state. When USB Sleep and Charge function is Enabled in TOSHIBA Hardware Setup, the USB Wakeup function does not work for compatible ports. The Wakeup setting (function to allow the Wakeup) check box will be displayed on the Device Manager and even though you can change the settings the USB Wakeup function will not work. If you want to use the USB Wakeup function, attach the mouse or keyboard to a USB port that does not have the USB Sleep and Charge function-compatible icon ( ).

ConfigFree

Toshiba does not guarantee that the fingerprint reader will recognize the enrolled user or accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of this fingerprint recognition software or utility.
All references to Bluetooth in this section are applicable only if Bluetooth is available on your system.
ConfigFree is a set of utilities that makes it easy to control communication devices and network connections. ConfigFree also lets you identify communication problems and create profiles for easy switching between locations and communication networks.
For more information on using ConfigFree, see the ConfigFree online Help.
The ConfigFree utilities include the following: Connectivity DoctorThe Connectivity Doctor utility is used to analyze network connections and fix networking problems with your notebook computer. For more information, see Connectivity Doctor on page 151. Profile SettingsThe Profiles utility lets you switch between network configurations. For more information, see Profile Settings on page 152.
This section contains information about the ConfigFree main screen, and how to start and set up ConfigFree. For more detailed information on setting up and using ConfigFree, see the Help File included in the application.

Starting ConfigFree

To start ConfigFree, be sure the computer has a wired or wireless connection. Then perform any of the following steps: Click Start, All Programs, Toshiba, Networking, and then ConfigFree. Double-click the ConfigFree icon in the Notification Area.
Press the TOSHIBA Assist button (if applicable to your system) to open the TOSHIBA Assist, and then click the ConfigFree icon. Click the ConfigFree icon then click the desired utility. in the Notification Area, and
If your computer is not connected to a network, the ConfigFree icon in the Notification Area is displayed with an X.
ConfigFree Utilities Connectivity Doctor
The Connectivity Doctor lets you analyze your network connections and fix network connection problems. Using Connectivity Doctor, you can view detailed network information by simply moving the mouse pointer. The Connectivity Doctor works with the following network devices: Wired and wireless network devices Access points Status of the PC Network Connections Status of wired and wireless connections Wireless Connection band (a/b/g etc.) Status of Wireless Connection switch
The Connectivity Doctor displays the following information:
(Sample Image) Connectivity Doctor screen

Profile Settings

The Profile Settings utility lets you save network settings in profiles. ConfigFree profiles are useful for easily switching network settings and devices. You can switch network settings simply by selecting the profile with the desired settings. If you visit a client company occasionally, for example, you can set up a profile to match that environment and connect to the network. Similarly, users who access networks in the office and at home can set up profiles to handle these networking environments. A profile contains the currently configured network settings on the computer, as well as information about any network devices. The following settings can be saved (or captured) in a profile: Internet settingsincludes LAN settings (proxy server settings) and the address of a home page that opens automatically when Internet Explorer starts Deviceslets you enable or disable settings of wired and wireless network devices, infrared devices, and set the power status of Bluetooth antennas TCP/IP settingsincludes DHCP, IP address, subnet mask, default gateway, DNS server, and WINS server settings Personal firewall settings for Internet connections Bluetooth Security Level (for example, high or medium) Enable UAC (User Account Control) setting

If you are using an AC adaptor, verify that the computer is receiving power from the external power source by looking at the AC power light. If the indicator is glowing, the computer is connected to a live external power source.
The computer starts but when you press a key nothing happens.
Verify that the active program accepts text input. Try clicking your mouse on an area where you can type text and try typing again. Your computer may be in Sleep mode and have a software or resource conflict. When this happens turning the power on returns you to the problem instead of restarting the system. To clear the condition, press Ctrl, Alt, and Del simultaneously. Then shut down the computer via software, or follow the steps if your program stops responding (see Problems that are easy to fix on page 154). Clearing the condition may get the computer running, but it will not solve a resource conflict. Read the documentation that came with the conflicting device and Resolving a hardware conflict on page 160.
The computer is not accessing the hard disk or the optional external diskette drive.
Your computer normally loads the operating system from the hard disk. If you have a hard disk problem, you will not be able to start the computer. Insert a system diskette into the optional external diskette drive and press F12 when the machine starts and use the arrow keys to select the boot-up device. (You may need to press F12 several times.)
The computer displays the WARNING RESUME FAILURE/Windows Error Recovery Windows did not shut down successfully message.
To continue, select Start Windows normally. This can happen if the computer was put into Sleep mode and the battery has discharged. If you performed a shutdown before this message was displayed, a program or driver may have prevented Windows from shutting down. Data stored in the computers memory has been lost. Data stored in the computers hard drive may not be affected. Always save your data even when you are using Sleep mode. If your battery fully discharges, information that has not been saved will be lost. Your computer can be configured to warn you when the battery is running low see What to do when the main battery runs low on page 100.
If you are running on battery power, it is recommended that you do not leave the computer in Sleep mode for long periods of time. To charge the battery, leave the computer plugged into a live wall outlet for several hours. For more information see Charging batteries on page 96.

The screen does not look right.
You can change the display settings by clicking a blank area of the desktop with the secondary control button, then clicking Personalize. This opens the Personalization window. Click Windows Color and Appearance to choose the colors for the screen. Click Display settings to choose the screen resolution.
The built-in screen flickers.
Some flickering is a normal result of the way the screen produces colors. To reduce the amount of flickering, try using fewer colors. To change the number of colors displayed: 3 Right-click in a blank area of the Windows desktop. Click Personalize, and then Display Settings. Change the Colors option and click OK.
For more information see Windows Help.
A message displays saying that there is a problem with your display settings and that the adapter type is incorrect or the current settings do not work with your hardware.
Reduce the size of the color palette to one that is supported by the computers internal display. To change the display properties: Right-click in a blank area of the Windows desktop. Click Personalize, and then Display Settings. Adjust the screen resolution and/or color quality. Click OK.
The display mode is set to Simultaneous and the external display device does not work.
Make sure the external monitor is capable of displaying at resolutions of 800 x 600 or higher. Devices that do not support this resolution will only work in Internal/External mode, and not simultaneous mode.
Small bright dots appear on your TFT display when you turn on your computer.

Disk drive problems

Problems with the hard disk or with a diskette drive usually show up as an inability to access the disk or as sector errors. Sometimes a disk problem may cause one or more files to appear to have garbage in them. Typical disk problems are:
You are having trouble accessing a disk, or one or more files appear to be missing.
Make sure you are identifying the drive by its correct name (A: or C:).

Error-checking

Run Error-checking, which analyzes the directories, files and File Allocation Table (FAT) on the disk and repairs any damage it finds. To run Error-checking: 3 Click Start, and then Computer. Right-click the drive you want to check. On the pop-up menu, click Properties. The drives Properties box appears.

warranty limited warranty 38 Web 117 Web Camera 121 Web sites 183 Wi-Fi wireless networking 114 Windows Media Player 90 Windows Explorer 81 Windows operating system Help and Support 160 problem solving 158 Windows operating system desktop 111 Windows Start menu 81 wireless networking 114 Wizards Connect to the Internet 115 World Wide Web 117 www 117
Taskbar 113 telephone line connecting to modem 115 television adjusting display 63 Toshiba registering computer 44 worldwide offices 184 TOSHIBA Assist 127 TOSHIBA Hardware Setup 139 Toshiba online resources 93 traveling tips 110 troubleshooting DVD player general problems 176 external keyboard 164