Users Manual xiii

The charge for a Telepermit assessment is $337.50. An additional charge of $337.50 is payable where an assessment is based on reports against non-Telecom New Zealand Specifications. $112.50 is charged for each variation when submitted at the same time as the original. An invoice for $NZ1237.50 will be sent under separate cover.
Following information is only for EU-member states:
The symbol indicates that this product may not be treated as household waste. Please ensure this product is properly disposed as inappropriate waste handling of this product may cause potential hazards to the environment and human health. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. This symbol may not be displayed depending on the country and region where you purchased.

EnergyStar Program

Your computer model may be Energy Star Compliant. If the model you purchased is compliant, it is labeled with the ENERGY STAR logo on the computer and the following information applies. TOSHIBA. is a partner in the Environmental Protection Agencys (EPA) Energy Star Program and has designed this computer to meet the latest Energy Star guidelines for energy efficiency. Your computer ships with the power management options preset to a configuration that will provide the most stable operating environment and optimum system performance for both AC power and battery modes. To conserve energy, your computer is set to enter the low-power Sleep Mode which shuts down the system and display within 15 minutes of inactivity in AC power mode. We recommend that you leave this and other energy saving features active, so that your computer will operate at its maximum energy efficiency. You can wake the computer from Sleep Mode by pressing the power button. According to the EPA, a computer meeting the new ENERGY STAR specifications will use between 20% and 50% less energy depending on how it is used. If all U.S. household and businesses replaced old computers with new ENERGY STAR qualified models, we would save more than $1.8 billion in energy costs over the next five years and avoid greenhouse gas emissions equivalent to more than 2.7 million cars. If every computer purchased by businesses next year met the new ENERGY STAR requirements, businesses would save more than $210 million over the lifetime of those models. That is equivalent to lighting 120 million square feet of U.S. commercial building space each year.

Type of battery that can be used for the remote controller
When the provided batteries run down, please replace them with adequate ones. CR2016 type battery is available. Other types or battery should not be used.

Installing the batteries

1. Open the battery cover on the back side of the remote controller.

Battery Cover

Opening the battery cover
2. Be sure to place the batteries with correct polarities. Press the battery down to the stopper then push it forward to fit into the battery case.

Stopper

Battery

Inserting the batteries

3. Close the battery cover. Close the cover securely until it clicks.
Closing the battery cover

Replacing the batteries

When the batteries in the remote controller reach the end of their life, the remote controller may not operate correctly or work only within a short distance from your computer. In this instance, you should purchase new batteries and replace the discharged ones.
1. Open the battery cover on the back side of the remote controller. 2. Hold down the stopper and slide the battery out of battery case.

Removing the batteries

3. Insert the battery in place. Be sure to place the batteries with correct polarities. Press the battery down to the stopper then push it forward to fit into the battery case. 4. Close the battery cover. Close the cover securely until it clicks.
Placing slim size remote controller
Inserting a slim size remote controller
To insert the slim size remote controller, follow the steps below. 1. Make sure the ExpressCard slot is empty. 2. Set the front side upward and insert the slim size remote controller.
Inserting the slim size remote controller
3. Press gently to ensure a firm connection.
Remove a slim size remote controller
To remove the slim size remote controller, follow the steps below. 1. Press the slim size remote controller slightly to make it stretch out. 2. Grasp the slim size remote controller and pull it out from the slot.
This chapter provides basic information to get you started using your computer. It covers the following topics: Be sure also to read the Instruction Manual for Safety and Comfort. This guide, which is included with the computer, explains product liability. Installing the battery pack Connecting the AC adaptor Opening the display Turning on the power Windows Vista setup Turning off the power Restarting the computer System Recovery Options Create Optical Recovery Discs Restoring the preinstalled Software from the Recovery HDD Restoring the Preinstalled Software from Recovery Media

AUTO Mode Login screen

Turn on the computer. The Select Tiles screen will be displayed. Select the tile for facial authentication. "Please turn your face to the camera" will be displayed. Verification will be performed. If the authentication is successful, the image data taken in step 4 will be faded in and placed over one another. If an error occurs during authentication, you will be returned to the Select Tiles screen. 6. Windows Welcome screen will be displayed, and will be logged in automatically to Windows. 1. 2. 3. 4. 5.

1:1 Mode Login screen

Turn on the computer. The Select Tiles screen will be displayed. Select the tile for facial authentication. The Select Account screen will be displayed. Select the account, and click the arrow button. "Please turn your face to the camera" will be displayed. Verification will be performed. If the authentication is successful, the image data taken in step 6 will be faded in and placed over one another. If an error occurs during authentication, you will be returned to the Select Tiles screen. 8. Windows Welcome screen will be displayed, and will be logged in automatically to Windows. If authentication was successful, but an authentication error subsequently occurred during the login to Windows, you will be asked to provide your account information. 1. 2. 3. 4. 5. 6. 7.
Using the optical disc drive
Operation is the same for all optical media drives. The full-size drive provides high-performance execution of CD/DVD-based programs. You can run either 12 cm (4.72") or 8 cm (3.15") CDs without an adaptor. An ATAPI interface controller is used for CD/DVD operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. Refer also to the Writing CD/DVD with the DVD Super Multi drive section for precautions on writing to CD/DVD.

Loading discs

To load a disc, follow the steps below and refer to the figures. 1. a. When the power is on, press the eject button to open the drawer slightly.

Eject Button

Pressing the eject button
b. Pressing the eject button will not open the drawer when the disc drive's power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button.

Connecting

To connect the modem cable, follow the steps below.
The modular cable that comes with the computer must be used to connect a modem. Connect the end of the modular cable with the core to the computer. In case of a lightning storm, unplug the modem cable from the telephone jack. Do not connect the modem to a digital telephone line. A digital line will damage the modem. 1. Plug one end of the modular cable into the modem jack. 2. Plug the other end of the modular cable into a telephone jack.
Connecting the internal modem
Do not pull on the cable or move the computer while the cable is connected. If you use a storage device such as an optical drive or hard disk drive connected to a 16-bit PC Card, you might experience the following modem problems: Modem speed is slow or communication is interrupted. Skips may occur in sound.

Disconnecting

To disconnect the internal modem cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. In the same way, pull the cables other connector out of the computer.

Using the FM tuner

The availability of this feature is depending on the model you purchased. 1. Plug the FM tuner antenna into the FM Antenna jack.

FM Antenna jack

FM TUNER ANTENNA
Plug FM tuner antenna into the jack

Select Start

All Programs
FM Tuner Utility to start FM software.

Wireless communications

The computers wireless communication function supports both Wireless LAN and Bluetooth devices. Only some models are equipped with both Wireless LAN and Bluetooth functions.
Do not use the Wireless LAN (Wi-Fi) or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt Wi-Fi or Bluetooth operation. Turn Wi-Fi and Bluetooth functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any Wi-Fi or Bluetooth functionality. Always turn off Wi-Fi or Bluetooth functionality if the computer is near automatic control equipment or appliances such as automatic doors or fire detectors. Radio waves can cause malfunction of such equipment, possibly resulting in serious injury. It may not be possible to make a network connection to a specified network name using the ad hoc network function. If this occurs, the new network(*) will have to be configured for all computers connected to the same network in order to re-enable network connections. * Please be sure to use new network name.

The Wireless LAN feature is not available on all models. Where present, it supports the A,B, G and N standards but it is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with IEEE802.11 Wireless LAN standard. Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6 Mbit/s. (IEEE 802.11g) Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5, 2 and 1 Mbit/s. (IEEE 802.11b) Roaming over multiple channels Card Power Management Wired Equivalent Privacy (WEP) data encryption, based on the 128 bit encryption algorithm. Advanced Encryption Standard (AES) data encryption, based on 128 bit encryption algorithm.
Be sure to enable the encryption function otherwise you may expose your computer to illegal access by an outsider across the Wireless LAN which may cause intrusion, eavesdropping, and the loss or destruction of stored data. TOSHIBA strongly recommend the customer to enable the encryption function. TOSHIBA is not liable for the eavesdropping of data due to the use of Wireless LAN and the damage thereof.
Bluetooth Stack for Windows by TOSHIBA (depends on the model purchased)
Please note that this software is specifically designed for the following operating systems: Microsoft Windows Vista Detailed information regarding the use with these operating systems is listed below. Please refer also to the electronic information which is included with each software. This Bluetooth Stack is based on Bluetooth Version 1.1/1.2/2.0+EDR specification. TOSHIBA cannot confirm compatibility between any PC products and/or other electronic devices that use Bluetooth other than TOSHIBA notebook computers.
Release Notes related to the Bluetooth Stack for Windows by TOSHIBA
1. Fax application software: Regarding FAX application software, there are some software that you cannot use on this Bluetooth Stack. 2. Multi User: On Windows Vista, the use of Bluetooth is not supported in a multiuser environment. This means that, when you use Bluetooth, other users logged onto the same computer will not be able to use its Bluetooth functionality.

Product Support:

The latest information regarding Operating System support, Language Support or available upgrades can be found on our web site http:// www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or www.pcsupport.toshiba.com in the United States.

Monitoring battery capacity
Remaining battery power can be monitored using the following methods. Clicking the battery icon on the task bar Via the Windows Mobility Center window Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. The computer needs this time to check the battery's remaining capacity and to calculate the remaining operating time, based on the current power consumption rate and remaining battery capacity. The actual remaining operating time may differ slightly from the calculated time. With repeated discharges and recharges, the batterys capacity will gradually decrease. Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged.
Maximizing battery operating time
A batterys usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: CPU processing speed (Depends on the model you purchased) Screen brightness Cooling method (Depends on the model you purchased) System Sleep Mode System Hibernation Monitor power off How often and how long you use the hard disk, optical disc. How much charge the battery contained to begin with. How you use optional devices, such as a PC Card, to which the battery supplies power. Enabling Sleep Mode conserves battery power if you are frequently turning the computer off and on. Where you store your programs and data. Closing the display when you are not using the keyboard saves power. Operating time decreases at low temperatures. The condition of the battery terminals. Make sure the battery terminals stay clean by wiping them with a clean dry cloth before installing the battery pack.
Retaining data with power off
When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods. Battery pack (3cell, 6cell, 9cell) Approximately 1.5 days (Sleep mode, 3-cell) Approximately 3 days (Sleep mode, 6-cell) Approximately 5 days (Sleep mode, 9-cell) Approximately 1 month (Shut down mode, All type of battery packs) Approximately 1 month

RTC battery

Extending battery life
To maximize the life of your battery pack: At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below. 1. Turn off the computer's power. 2. Disconnect the AC adaptor and turn on the computer's power. If it does not turn on go to step 4. 3. Operate the computer on battery power for five minutes. If the battery pack has at least five minutes of operating time, continue operating until the battery pack is fully discharged. If the Battery indicator flashes or there is some other warning to indicate a low battery, go to step 4. 4. Connect the AC adaptor to the computer and the power cord to a power outlet. The Battery indicator should glow orange to indicate that the battery pack is being charged. If the Battery indicator does not glow, power is not being supplied. Check the connections for the AC adaptor and power cord. 5. Charge the battery pack until the Battery indicator glows white/ green. If you have extra battery packs, rotate their use. If you will not be using the system for an extended period, more than one month, remove the battery pack. Store spare battery packs in a cool dry place out of direct sunlight.

Latches

Removing the memory module
6. Seat the cover and secure it with screws and replace the battery pack.

Additional battery pack

You can increase the portability of the computer with additional battery packs. If youre away from an AC power source and your battery runs low, you can replace it with a freshly charged battery. Refer to Chapter 6, Power and Power-Up Modes.

Additional AC adaptor

If you frequently transport the computer between different sites such as your home and office, purchasing an AC adaptor for each location will reduce the weight and bulk of your carrying load.

External monitor

An external analog monitor can be connected to the external monitor port on the computer. Refer to Appendix B, Display Controller and Modes. The computer supports several video modes. To connect a monitor, follow the steps below. 1. Turn the computer off. 2. Connect the monitor to the external monitor port. 3. Turn the monitor's power on. 4. Turn the computer on. When you turn on the power, the Windows Bootup screen (Windows Logo) appears on the display device. However, the Windows Desktop appears on a display device that you used last time to shut down your PC, if the display device exists when you turn on the power. To change the display settings, press Fn+F5. If you disconnect the monitor before you turn the computer off, be sure to press Fn+F5 to switch to the internal display. Refer to Chapter 5, The Keyboard, for details on using hot keys to change the display setting.
A HDMI monitor can be connected to the HDMI out port on the computer. 1080p, 1080i, 720p, 576p and 480p signal formats can be supported. But actual signal format you can use depends on HDMI monitor. To connect monitor, follow the steps as detailed below: As the port operation of all HDMI (High-Definition Multimedia Interface) monitors has not been confirmed, some HDMI monitors may not function properly. 1. Plug one end of the HDMI cable into the HDMI port of the HDMI device.
Connecting a HDMI cable Users Manual 8-11
2. Plug the other end of the HDMI cable into the HDMI out port on your computer.
Setting for display video on HDMI
To view video on the HDMI device, be sure to configure the following settings otherwise you may find that nothing is displayed. Be Sure to use the FN + F5 hot keys to select the display device before starting to play video. Do not change the display device while playing video. Do not change the display device under the following conditions. While data is being read or written. While communication is being carried out.
Settings for audio on HDMI
To set the audio device to use the HDMI, follow the steps below. 1. Click Start. 2. Click Control Panel. 3. Click Hardware and Sound. 4. Click Sound. 5. Click Digital Output Device (HDMI). 6. Click the Set Default Device button. To set the audio device to use internal speaker, follow the steps below. 1. Click Start. 2. Click Control Panel. 3. Click Hardware and Sound. 4. Click Sound. 5. Click Speakers. 6. Click the Set Default Device button.

i.LINK (IEEE1394)

i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as 1. Digital video cameras 2. Hard disk drives 3. MO drives 4. CD-RW drives i.LINK uses a four-pin connector, which does not carry electric current. External devices will need their own power supply.

Precautions

1. Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. 2. Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise. Data can be destroyed. 3. If you are transferring data through an IEEE1394 hub, do not connect or disconnect other devices from the hub during data transfer. There is a likelihood that data will be damaged. Connect all devices to the hub before you turn on the computers power. 4. You may not use any copyrighted video or music data copied from a video camera except for your personal enjoyment. 5. If you connect/disconnect an i.LINK device to/from another i.LINK device that is currently exchanging data with the computer, data frames might be dropped. 6. Make sure data transfer has ended or turn off the computer, before you: a. Connect/disconnect an i.LINK device to/from the computer. b. Connect/disconnect an i.LINK device to/from another i.LINK device that is connected to the computer.
1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: a. You may need to install drivers for your i.LINK devices. b. Not all i.LINK devices have been tested. Therefore, compatibility with all i.LINK devices cannot be guaranteed. c. Use S100, S200 or S400 cables no longer than three meters. d. Some devices might not support sleep or automatic off functions. e. Do not connect or disconnect an i.LINK device while it is using an application or when the computer is automatically shutting it down to save power. Data might be destroyed. f. When multiple IEEE1394 devices are connected to a PC, the devices may not correctly be identified. This problem may occur when Windows Vista is restarted while the devices are connected or when the power to the IEEE1394 devices is turned on before the PC is turned on. If it occurs, disconnect the IEEE1394 cables and then reconnect them.
1. Open the Safety Remove Hardware icon on the Task Bar. 2. Point to i.LINK (IEEE1394) device and click. 3. Disconnect the cable from the computer then from the i.LINK device. Refer also to the documentation that came with your i.LINK device.
eSATA (External Serial ATA)
An device corresponding to eSATA function can be connected to the eSATA/USB combo port on the computer.

The response of the TouchPad is too sensitive

USB mouse

On-screen pointer does The system might be busy. If the pointer is not respond to mouse shaped as an hourglass, wait for it to resume its operation normal shape and try again to move it. Make sure the mouse is properly connected to the USB port. Double-clicking does not work Try changing the double-click speed setting in the mouse control utility. 1. To access this utility, click , Control Panel, Hardware and Sound, then Mouse icon. 2. Wihtin the Mouse Properties window, click the Buttons tab. 3. Set the double-click speed as required and click OK. The mouse pointer moves too fast or too slow Try changing the speed setting in the mouse control utility. 1. To access this utility, click , Control Panel, Hardware and Sound, then Mouse icon. 2. Within the Mouse Properties window, click the Pointer Options tab. 3. Set the pointer speed as required and click OK. The mouse might be dirty. Refer to your mouse documentation for instructions on cleaning. If problems persist, contact your dealer.
The mouse pointer moves erratically
Also refer to your USB devices documentation. Problem USB device does not work Procedure Check for a firm cable connection between the USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows Vista documentation for information on checking the drivers. If problems persist, contact your dealer.
Problem I cannot use the USB Sleep and Charge function. Procedure The setting of USB Sleep and Charge function may be [Disabled]. Change the setting to [Enabled] in the HW Setup. When there is a current overflow of the external device connected to the compatible port, USB bus power (DC5V) supply may be stopped for safety reasons. When this happens, disconnect an external device if some external devices are connected. After that, turn the power of the computer ON/OFF to restore the function. If this function can not be still used even if only one external device is connected, stop using the external device because its current is over the acceptable value of this computer. Some external devices may not be able to use the USB Sleep and Charge function. In this case, please try one or more of the following methods. Change a mode setting of [Enabled] by the HW

Appendix C

Card Specifications
Form Factor Compatibility Mini PCI TypeIII IEEE 802.11 Standard for Wireless LANs Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The "Wi-Fi CERTIFIED" logo is a certification mark of the Wi-Fi Alliance. Microsoft Windows Networking CSMA/CA (Collision Avoidance) with Acknowledgement (ACK) 54/48/36/24/18/12/9/6 Mb/s (IEEE 802.11a/g) 11/5.5/2/1 Mb/s (IEEE 802.11 b)
Network Operating System Media Access Protocol Data Rate

Radio Characteristics

Radio Characteristics of Wireless LAN Cards may vary according to: Country/region where the product was purchased Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment. Refer to the sheet "Information to the User" for regulatory information that may apply in your country/region. R-F Frequency Band 2.4GHz (2400~2497 MHz) for 802.11b/g/n (draft version) Band 5GHz (5150~5850 MHz) for 802.11a/n (draft version) DSSS-CCK, DSSS-DQPSK, DSSS-DBPSK (IEEE 802.11b) OFDM-BPSK, OFDM-QPSK, OFDM16QAMOFDM-16QAM (IEEE 802.11a/g)

Modulation Technique

The range of the wireless signal is related to the transmit rate of the wireless communication device. Communications at a lower transmission rate may travel larger distances. The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials. Range is also impacted due to obstacles in the path of the transmission that may either absorb or reflect the radio signal.
Supported Frequency Sub-bands
Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
Wireless IEEE 802.11 Channels Sets (Revision B, G and draft N)

Memory (Main System)

Part of the main system memory may be used by the graphics system for graphics performance and therefore reduce the amount of main system memory available for other computing activities. The amount of main system memory allocated to support graphics may vary depending on the graphics system, applications utilized, system memory size and other factors. For PCs configured with 4 GB of system memory, the full system memory space for computing activities will be considerably less and will vary by model and system configuration.

Battery Life

Battery life may vary considerably depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery life numbers are achieved on select models and configurations tested by TOSHIBA at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power. After going through many charge and discharge cycles, the battery will lose its ability to perform at maximum capacity and will need to be replaced. This is a normal phenomenon for all batteries. To purchase a new battery pack, see the accessories information that is shipped with your computer.
Hard Disk Drive (HDD) Capacity
1 Gigabyte (GB) means 109 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for the definition of 1 GB = 230 = 1,073,741,824 bytes, and therefore shows less storage capacity. Available storage capacity will also be less if the product includes one or more pre-installed operating systems, such as Microsoft Windows and/or pre-installed software applications, or media content. Actual formatted capacity may vary.
Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology. Maximum brightness is only available when operating in AC power mode. The screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen.

data: Information that is factual, measurable or statistical that a computer can process, store, or retrieve. data bits: A data communications parameter controlling the number of bits (binary digits) used to make up a byte. If data bits = 7 the computer can generate 128 unique characters. If data bits = 8 the computer can generate 256 unique characters. DC: Direct Current. Electric current that flows in one direction. This type of power is usually supplied by batteries. default: The parameter value automatically selected by the system when you or the program do not provide instructions. Also called a preset value. delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program (called a driver) that permits a computer to communicate with a device. dialog box: A window that accepts user input to make system settings or record other information. disable: To turn a computer option off. See also enable. disk drive: The device that randomly accesses information on a disk and copies it to the computers memory. It also writes data from memory to the disk. To accomplish these tasks, the unit physically rotates the disk at high speed past a read-write head. disk storage: Storing data on magnetic disk. Data is arranged on concentric tracks much like a phonograph record. display: A CRT, LCD, or other image producing device used to view computer output.

Glossary-5

documentation: The set of manuals and/or other instructions written for the users of a computer system or application. Computer system documentation typically includes procedural and tutorial information as well as system functions. double click: To press and release the pointing device's primary button rapidly twice without moving the pointing device. In the Windows operating system, this refers to the pointing device's left button, unless otherwise stated. driver: A software program, generally part of the operating system, that controls a specific piece of hardware (frequently a peripheral device such as a printer or mouse). DVD: An individual digital versatile (or video) disc. See also DVD-ROM. DVD-R (+R, -R): A Digital Versatile Disc-Recordable disk can be written once and read many times. The DVD-R drive uses a laser to read data from the disc. DVD-RAM: A Digital Versatile Disc-Random Access Memory is a high capacity, high performance disc that lets you store large volumes of data. The DVD-ROM drive uses a laser to read data from the disc. DVD-ROM: A Digital Versatile Disc-Read Only Memory is a high capacity, high performance disc suitable for play back of video and other high-density files. The DVD-ROM drive uses a laser to read data from the disc. DVD-RW (+RW, -RW): A Digital Versatile Disc-ReWritable disc can be rewritten many times.

terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output. TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest.
USB: Universal Serial Bus. This serial interface lets you communicate with several devices connected in a chain to a single port on the computer.
VGA: Video Graphics Array is an industry standard video adaptor that lets you run any popular software. volatile memory: Random access memory (RAM) that stores information as long as power is supplied to the computer.
warm start: Restarting or resetting a computer without turning it off. Wi-Fi: A registered trademark term of the Wi-Fi Alliance that stands for Wireless Fidelity, and is another term for the communication protocol to permit an Ethernet connection using wireless communication components.

Glossary-12

window: A portion of the screen that can display its own application, document or dialog box. Often used to mean a Microsoft Windows window. Wireless LAN: Local Area Network (LAN) through wireless communication. Wireless WAN: Wide Area Network (WAN) through wireless communication. write protection: A method for protecting a floppy diskette from accidental erasure.

Glossary-13

Glossary-14
AC adaptor, 1-4 additional, 1-15 connecting, 3-3 ASCII characters, 5-7 Display controller, B-1

Equipment checklist, 1-1

Floppy disk using, 4-17 Fn + Esc (sound mute), 5-3 Fn + F1 (instant security), 5-3 Fn + F2 (power save mode), 5-3 Fn + F3 (Sleep Mode), 5-3 Fn + F4 (hibernation), 5-3 Fn + F5 (display selection), 5-3 Fn + F6 (Display Brightness decreases), 5-4 Fn + F7 (Display Brightness increases), 5-4 Fn + F8 (Wireless setting), 5-4 Fn + F9 (Touch Pad), 5-4 Fn Sticky key, 5-5 Function keys, 5-2
Battery charging, 6-8 extending battery life, 6-11 indicator, 6-1 location, 2-6 Monitoring capacity, 6-10 real time clock, 1-4, 6-4 safety precautions, 6-6 save mode, 1-9 types, 6-3 Battery pack, 1-4 additional, 8-10 replacing, 6-12
Cleaning the computer, 4-37
Display, 1-5 automatic power off, 1-9 brightness decreases, 5-4 brightness increases, 5-4 controller, 1-6 opening, 3-4

Graphics controller, 1-6

Hard disk drive, 1-4 automatic power off, 1-9 Hibernation, 1-10, 5-3 HW Setup, 1-12

Index-1

Keyboard, 1-6, 5-1 emulating keys on enhanced, 5-2 F1. F12 function keys, 5-2 hot keys, 5-3 typewriter keys, 5-1 Windows special keys, 5-5 Keypad overlay, 1-9, 5-6 numeric mode, 5-6 temporarily using normal keyboard (overlay on), 5-7 turning on the overlays, 5-6
LAN, 1-7, 4-36 cable types, 4-36 connecting, 4-36 disconnecting, 4-37
Media care, 4-29 CD/DVDs, 4-29 Memory, 1-3 expansion, 1-15, 8-7 installing, 8-7 removing, 8-9 Modem, 1-7, 4-30 connecting, 4-31 disconnecting, 4-32 properties menu, 4-31 region selection, 4-30 Monitor, external, 1-6, 8-11