Suspension bracket fixing points (4 points)
p.48 Install the optional ceiling mount here when suspending the projector from a ceiling.

Lamp cover

Air filter (air intake vent)
p.44, 46 Prevents dust and other foreign particles from being drawn into the projector. It should be cleaned periodically.
Open this cover when replacing the lamp inside.

Appearance

Centre of projector

Centre of lens

131.5 66*1
406 *1 Distance from centre of lens to suspension bracket fixing point (Lens shift amount: Max. 8.8 mm vertically) *2 Distance from centre of lens to centre of projector (Lens shift amount: Max. 7.7 mm horizontally) Centre of lens 300 52.8

310 160

Units:mm

Setting up

Adjusting the projection size
The size of the projected image is basically determined by the distance from the projector's lens to the screen.
Lens shift Top Offset Centre of lens Offset Lens shift Bottom
Adjusting the projection the lens to the bottom of the size The height from the centre of
Projection distance screen will vary depending on the lens shift setting.
While referring to the table below, position the projector so that the images are projected onto the screen at the optimum size. The values should be used as a guide for setting up the projector.
Units: cm (in.) Units: cm (ft.) Projection distance 16:9 screen size
30" 40" 60" 80" 6637 (2615) 8950 (3520) 13075 (5128) 180100 (7139) 220120 (8747) 270150 (10659) 330190 (13075) Longest Shortest to (Tele) (Wide) 87 to 188 (2.8 to 6.2) 117 to 252 (3.8 to 8.3) 177 to 380 (5.8 to 12.5) 238 to 508 (7.8 to 16.7) 298 to 636 (9.8 to 20.9) 359 to 764 (11.8 to 25.1) 450 to 956 (14.7 to 31.4) Offset

Units: cm (in.)

to Offset
17 to -17 (6.8 to -6.8) 23 to -23 (9.1 to -9.1 ) 35 to -35 (13.6 to -13.6) 46 to -46 (18.2 to -18.2) 58 to -58 (22.7 to -22.7) 69 to -69 (27.2 to -27.2) 86 to -86 (34.0 to -34.0)

100"

120" 150"
Units: cm (ft.) Projection distance

Offset

4:3 screen size
30" 40" 60" 80" 6146 (2418) 8161 (3224) 12090 (4735) 160120 (6347) 200150 (7959) 240180 (9471) 300230 (11891)
Longest Shortest to (Tele) (Wide) 106 to 230 (3.5 to 7.6) 143 to 309 (4.7 to 10.1) 217 to 465 (7.1 to 15.3) 291 to 622 (9.6 to 20.4) 365 to 778 (12.0 to 25.5) 439 to 935 (14.4 to 30.7) 550 to 1170 (18.0 to 38.4)
21 to -21 (8.3 to -8.3) 28 to -28 (11.1 to -11.1 ) 42 to -42 (16.7 to -16.7) 56 to -56 (22.2 to -22.2) 71 to -71 (27.8 to -27.8) 85 to -85 (33.3 to -33.3) 106 to -106 (41.7 to -41.7)

Lens shift adjustment

The lens shift dials can be used to position the image and is especially useful when using the projector in the following locations. p.16 Hanging from the ceiling A screen in a high location Projector situated to the side so that the screen can be viewed sitting right in front of it Projector situated on a shelf, etc. When positioning an image using the lens shift dial, hardly any deterioration of the image occurs because the lens shift correction is adjusted optically. However, for optimal image quality the lens shift function should not be used.

Projection methods

Avoid setting the projector up in a place which is very dusty or humid, or where there will be cigarette or other smoke, especially oily smoke. Clean the air filter at least once every 3 months. Clean the air filter more frequently if using the projector in a dusty environment. A special method of installation is required when suspending the projector from the ceiling (ceiling mount). If it is not installed correctly, it could fall causing an accident and injury.
When projecting from directly in front
When projecting from the side of the screen
When projecting from a celling
* Even if projection will be from the screen side, set up the screen and projector so that they are parallel.
* When suspending the projector from a ceiling, change the configuration menu settings. p.34
Configuration menu Settings Projection Front Front/Ceiling
If you use adhesives on the ceiling mount to prevent the screws from loosening, or if you use things such as lubricants or oils on the projector, the projector case may crack causing it to fall from its ceiling mount. This could cause serious injury to anyone under the ceiling mount and could damage the projector. When installing or adjusting the ceiling mount, do not use adhesives to prevent the screws from loosening and do not use oils or lubricants and so on. Do not use the projector on its side. This may cause malfunctions to occur.

Connecting Image Sources

Turn the power off for both the projector and the signal source before connecting them. If the power for either device is on at the time of connection, damage may result. Check the shapes of the cable connectors and the device ports before making the connections. If you try to force a connector to fit a device port with a different shape or number of terminals, a malfunction or damage to the connector or port may result.
Video equipment (VHS VCR, DVD player, game console, etc.) Computer
*Port names may vary depending on the equipment being connected.

S-Video

Component output SCART*

Mini D-Sub 15-pin

S-Video cable (commerciallyavailable)
RCA video cable (commerciallyavailable)

SCART cable

(commerciallyavailable) +

D SCART adapter*2

(accessory)
Component video cable (commerciallyavailable)
HDMI cable (commerciallyavailable)
Computer cable (commerciallyavailable)
*1 If a DVD has been connected using a D SCART adapter, change the "D/SCART" setting in the "Input Signal" to "SCART". p.34 *2 Some regions may not have the D SCART adapter included as an accessory.

Remove the lens cover.

Turn the power on.
Control Panel Remote Control
Connect the power cable. Turn on the main power switch.
Turn the power on for the connected equipment.
If there is a problem with projection even though the projector is set up and connected correctly, refer to p.15, 36. If you set the "Direct Power On" to "On", the power of the unit will turn ON when the main power switch is turned ON, without having to press the power button of the remote control or the projector's control panel. The projector is equipped with a "Child Lock" function that prevents young children from accidentally turning the power on and looking into the lens, and also an "Operation Lock" function that prevents mis-operations. p.33 When using above an altitude of about 1500 m, make sure you set the "High Altitude Mode" to "On". p.33 This projector is equipped with an automatic adjustment function that automatically optimizes it when a computer input signal is switched. If a laptop computer or a computer with a LCD screen has been connected to the projector, you may need to use keyboard or function settings to change the output destination. While holding down the key, press (the key with a symbol such as / on it). After the selection is made, projection will soon start. Computer documentation
Example of output selection
NEC Panasonic SOTEC HP Toshiba IBM SONY DELL Fujitsu
Set mirror setting or display detection. Depending on OS, you can change the output selection by pressing.

Macintosh

When the expected images are not projected
If more than one signal source has been connected, or if no images are projected, use the remote control or the projector's control panel buttons to select the signal source. For video devices, press the [Play] button on the video equipment first, then select the signal source. Using the remote control Using the control panel
When the expected images are not projected Turning the power off
Press the button that has the name of the port on it that the desired signal source is connected to. When you press , the menu is displayed. Each press of moves the pointer. Move the pointer to the target input source to select it. Press to accept. The input source is automatically changed if no operations are performed for about 5 seconds with the pointer at the target input source.
When the colour of the image projected from the [D] or [Component] input port is unnatural, select an appropriate signal according to the signal from the device connected at "Input Signal" in the Configuration menu. p.34

Turning the power off

Turn the power off for the signal sources that are connected to the projector. Press on the remote control or on the projector's control panel. If you press on the projector's control panel, the following message will be displayed. Press again to continue. When the projector has cooled down (takes about 30 seconds), turn off the main power switch. Simply pressing or electricity consumption. does not stop

Attach the lens cover.

Adjusting the Projection Screen

Focus adjustment

Turn the focus ring to adjust the focus.
Fine adjustments to image size (Zoom adjustment)
Turn the zoom ring to adjust the size of the projected image.

Wide Tele

Projection image position adjustment (Lens shift) Fine adjustments to image
The lens shift function can be used to move the image display position vertically and horizontally within the range shown in the figure on the right when you cannot set up this projector directly in front of the screen, or when the image is projected too low or too high. When you turn the lens shift dial and hear a click, the lens position is almost centred.

size (Zoom

adjustment)
Projection image position adjustment (Lens shift)
The image display position cannot be moved to the maximum positions in both the vertical and horizontal positions. Ex) The image cannot be shifted vertically when it has been shifted horizontally by the full amount. When the image has been shifted vertically by the full amount, it can be shifted up to 9% of the horizontal width of the screen.

1/2V 1/2H

Move downwards

Move to the left

Move to the right
When transporting the projector, make sure to turn the lens position down by the full amount. Otherwise the lens shift mechanism may be damaged.
Move upwards Standard projection position (centre position for lens shift) Range that the picture can be shifted from the standard projection position
Correcting projector tilt
If the projected images are tilted horizontally ( so that it is horizontal. ), use the front adjustable feet to adjust the projector

Extend

Retract
Displaying a test pattern
You can project a test pattern at times such as when setting up the projector in order to perform adjustments in the line menu, and zoom and focus adjustments without having to connect video equipment. If on the remote control is pressed, the test pattern appears.
To stop displaying the test pattern, press again. Displaying a test pattern
Basic Image Quality Adjustments
Selecting the colour mode
Press and select the colour mode from the menu. Setting is also possible using the configuration menu.
Selecting the aspect Selecting the aspect
Select Menu Operations Press or on the remote control or on on the projector's control panel to select an item. Press or to confirm the selection. *If you press , the Select menu disappears.

Press menu.

and select the aspect mode from the
When projecting using Auto For 4:3 input signals For input images recorded in squeeze mode For letterbox input signals Normal Full Zoom
If you project an image that is compressed, enlarged or separated using the aspect function in public places such as a store or hotel for the purposes of profit-making or public display, it may result in infringing on the author's right that is protected by copyright law.
*1 Not usable during computer input. Not compatible with certain component video signals. *2 If Auto is not suitable, the setting will become Normal.
: Ideal for using in bright rooms. : Living Room Ideal for using in rooms in which the curtains are closed. : Ideal for using in dark rooms. Natural It is recommended that you start in this mode when making colour adjustments. : Ideal for using in dark rooms. Theatre Dynamic
Theatre Black 1 Theatre Black 2
: Suitable for use in a completely darkened room. 1: A clear tone of colour one might see in professional monitors used when creating DVD software. 2: A deep warm tone of colour that gives you the feeling of enjoying a movie at the theatre.
When you select the colour mode indicated with , the Epson Cinema Filter will be applied automatically to increase the contrast and makes skin tones more natural.

Input signal

Normal TV broadcasts Images with standard aspect ratio (4:3) Computer images
Images recorded by a video camera or DVD software in squeeze mode

Letterbox images

Normal TV broadcasts Images with standard aspect ratio (4:3)

Recommended aspect mode

Normal

Result

Black bands will appear at the left and right of the images.
Input signals will be projected at the same width as the projector's panel resolution.
Input signals will be projected at the same height as the projector's panel resolution.
When a 4:3 image is projected, the top and bottom of the image are hidden from view. If this happens, the part of the image hidden from view at the top and bottom can be reduced in size in the vertical direction so that it can be viewed by "Zoom Size" in the Configuration menu. p.31 When images with subtitles are projected and the subtitles are truncated, use the "Zoom Caption Pos." menu command to adjust. p.31
When HDTV images are projected, the images appear in 16:9 size.
When 4:3 images are projected, the images will be elongated horizontally.
Input signals will be projected at the same height as the projector's panel resolution. At this time, the image enlargement ratio will be smaller near the middle of the images but become larger towards the left and right edges of the images. This is useful for when 4:3 images are projected onto a wide screen. Because there is almost no distortion due to enlargement in the middle of the images, the images appear close to what they would be at their original size. And because both ends of the images are enlarged, movement at the edges of the images appears faster and gives an impression of greater speed, making it ideal for viewing sporting events.

to select an item, then press
next to it is selected, the selection screen for that item.
List of configuration menus
When no image signals are being input, the "Image" menu and the "Signal" menu cannot be adjusted. Also, the items displayed in the "Image" menu, the "Signal" menu and the "Info" menu will vary depending on the type of image signals that are being projected.
Displayed for input sources other than computer * This is displayed in the line menu.
Color Mode Image Brightness Contrast Color Saturation Tint Sharpness Abs. Color Temp. Skin Tone Advanced Brightness Control Auto Iris Reset
p.30 p.30 p.30 p.30 p.30 p.30 p.30 p.30 p.30 p.31 p.31 p.31
Dynamic, Living Room, Natural, Theatre,Theatre Black 1, Theatre Black 2 * * * * * * *

Standard Advanced Gamma

Thin Line Enhancement, Thick Line Enhancement Vert. Line Enhancement, Horiz. Line Enhancement
2.0, 2.1, 2.2, 2.3, 2.4 Customized Adjust it from the image

Adjust it from the graph

High, Low On, Off Yes, No

Reset RGB RGBCMY

Offset R, G, B Gain R, G, B R (Hue/Saturation), G (Hue/Saturation), B (Hue/Saturation), C (Hue/Saturation), M (Hue/Saturation), Y (Hue/Saturation)
Only displayed for Computer input (does not appear when signals from the [HDMI] input port are being input)
Aspect Signal Zoom Size Zoom Caption Pos. Tracking Sync. Position Auto Setup

Progressive

p.31 p.31 p.31 p.31 p.31 p.31 p.31 p.32 p.32 p.31 p.32 p.31 p.32 p.32 p.32 p.33 p.33
Auto, Normal, Full, Zoom, Wide
On, Off Off, Video, Film/Auto
Motion Detection Noise Reduction
Output Scaling Setup Level
Off, NR1, NR2, NR3 Auto, 100%, 98%, 96%, 94%, 92% 0%, 7.5% On, Off Normal, Expanded Yes, No

EPSON Super White

HDMI Video Range

Direct Power On

Settings

On, Off

Off, 5min., 10min., 30min.

Sleep Mode

Child Lock

Operation Lock

Trigger Out

High Altitude Mode

Projection
Front, Front/Ceiling, Rear, Rear/Ceiling

Display

Tracking

This adjusts the images if vertical stripes appear in the images.
This adjusts the images if flickering, fuzziness or interference appear in the images. Flickering and fuzziness may also occur when the brightness, contrast and sharpness settings are adjusted. Clearer adjustments can be obtained if you adjust the "Tracking" first and then adjust the "Sync".

Position *1

(Setting is not possible when signals are being input from the [HDMI] input port.) When part of the image is clipped, move the image display position vertically and horizontally so that the entire image is projected. Press , , and to adjust the position.

Auto Setup

This sets automatic adjustment to on or off in order to set whether the projector automatically adjusts images to their optimum condition when the input signal is changed. The three automatically adjusted items are "Tracking", "Position" and "Sync."
*1 The setting values are stored separately for each image source and signal type. *2 The setting values are stored separately for each image source and colour mode setting. *3 The setting values are stored separately for each colour mode setting.

Progressive *1

(This can be set only when signals are being input from the [Video] / [S-Video] input port, 525i, 625i signals are being input from the [SCART] input port, or 525i, 625i, 1125i signals are being input from the [Component] / [HDMI] input port.) Interlace (i) signals are converted to progressive (p) signals using a method appropriate for the image. Off :This is ideal for using when viewing images with a large amount of movement. Video :This is ideal for general video images. Film/Auto :By pulling down 3-2/2-2, images (e.g. video films/CG or animations) recorded in 24/30 frames are automatically converted to the optimum progressive signals so that images are reproduced looking natural as originally intended.

Motion Detection *1

(This can be set only when signals are being input from the [Video] / [S-Video] input port, 525i, 625i signals are being input from the [SCART] input port, or 525i, 625i, 1125i signals are being input from the [Component] / [HDMI] input port.) Select whether the progressive conversion operation mode is for fast-moving images or for slow-moving images. The smaller the value, the more suitable the mode is for viewing still images. The larger the value, the more suitable the mode is for viewing video images.

Noise Reduction *1

This reduces flickering of images. Three modes are available. Select the mode to suit your liking. Set "Off" when the image source, such as DVD, contains little electrical interference.

Output Scaling *1

(Setting is not possible when composite video , S-Video , or computer signals are being input.) This changes the display area (the part of projected images). 100% - 92% :When 100% is set, the top and bottom of the image is sometimes affected by electrical interference depending on the image signal. In such cases, try to adjust the display position ("Position"). p.31 Auto :Displayed when the signals from [HDMI ] input port are being input. Signals are automatically projected at 100% or 92% size depending on the input signals. (Not displayed when the equipment's DVI port is connected to the projector's [HDMI] input port.)

Setup Level *1

(This can be set when NTSC signals are being input from the [Video] / [S-Video] input ports, when composite video signals are being input from the [Component] input port, or when signals are being input from the [SCART] input port.) If using products designed for destinations such as South Korea that have different black level (setup level) settings, use this function to obtain correct images. Check the specifications of the connected equipment when changing this setting.

EPSON Super White *1

(Setting is only possible when Color Mode is "Natural", "Theatre", "Theatre Black 1", or "Theatre Black 2", and composite video, S-video, component video, or SCART signals are being input.) If bright white areas of images such as clouds and T-shirts on the beach in summer appear uneven and overexposed, set to "On". When set to "On", the "HDMI Video Range" setting will be ignored.
*1 The setting values are stored separately for each image source and signal type.

HDMI Video Range*1

(Setting is possible only when "EPSON Super White" is "Off".) When the [HDMI ] input port of the projector is connected to a DVD player, for example, set the video range of the projector to suit the video range setting of the DVD player. The setting at the DVD player can be either Normal or Expand.
All the adjustment values on the "Signal" menu, except "Aspect ", are returned to their default values.

(operation) indicator

(warning) indicator

When the

(warning) indicator is lit or flashing warning/problem

: Lit : Flashing

Internal problem / Fan problem / Sensor problem / Cinema filter problem / Auto iris problem
Disconnect the power cable from the electrical outlet. Then contact your local dealer or the nearest address provided in the World-Wide Warranty Terms. Inquiries

(Lit/off for 1 sec) Red

Lamp problem / Lamp on error / Lamp cover open error Check if the lamp is broken. p.46 Clean the air filter. p.44
Replace the lamp and then turn the power on. If the problem is still not solved after the lamp is replaced, stop using the projector and disconnect the power cable from the electrical outlet. Then contact your local dealer or the nearest address provided in the World-Wide Warranty Terms. Inquiries
(Lit/off for 0.5 sec) If the lamp is not broken

If the lamp is broken

Contact your local dealer for further advice.
Check that the lamp and the lamp cover are securely installed. When using above an altitude of about 1500 m, make sure you set the "High Altitude Mode" to "On". p.33 Red
High internal temperature (overheating)
The lamp will switch off automatically and projection will stop. Wait for approximately 5 minutes. When the cooling fan stops, turn off the main power switch at the rear of the projector. If the projector is installed against a wall, leave a space of 20 cm or more between it and the wall. Clean the air filters if they are blocked. p.44

Orange

High-speed cooling in progress
You can continue using the projector, but if the temperature rises again, it will switch off automatically.
If the problem is not solved when the power is turned back on, stop using the projector, turn off the main power switch, and disconnect the power cable from the electrical outlet. Then contact your local dealer or the nearest address provided in the World-Wide Warranty Terms. Inquiries
(operation) indicator is lit or flashing normal
(warning) indicator is off
: Lit , projection will start after a brief interval. : Flashing
Standby condition If you press Warm-up in progress Projection in progress in
Warm-up time is approximately 30 seconds.
Power off operations are ignored while warm-up is in progress. Normal operation is in progress. Cool-down time is approximately 30 seconds. After cool-down is complete, the projector goes to standby mode. You cannot use the remote control or the projector's control panel during cool-down. If the main power switch at the rear of the projector is turned off before cool-down is complete, wait for the lamp to cool down (normally about one hour is required) before turning the power back on again.

Has the "Position" setting been adjusted correctly? Has the computer been set for dual display? Only when projecting computer images
Has the correct resolution been selected? Only when projecting computer images
Set the computer so that the signals that are output are compatible with this projector. "List of Supported Monitor Displays" p.49 Computer documentation
Image colours are not right
Are the cables connected correctly? Has the image contrast been adjusted correctly? Has color been adjusted appropriately? Have the colour intensity and tint been adjusted correctly? Only when projecting images from a video source
Check that all of the cables required for projection are securely connected. p.12 Use the "Contrast" menu command to adjust the color. "Image" - "Contrast" p.30 Use the "Advanced" menu command to adjust the colour. "Image" - "Advanced" p.30 Use the "Color Saturation" and "Tint" menu commands to adjust the colour and tint. "Image" - "Color Saturation", "Tint" p.30

Images appear dark

Has the image brightness been adjusted correctly? Has the image contrast been adjusted correctly? Is the lamp due for replacement?
Use the "Brightness" menu commands to make the adjustments. "Image" - "Brightness" p.30 Use the "Contrast" menu command to adjust the color. "Image" - "Contrast" p.30 When the lamp is nearly due for replacement, the images will become darker and the colour quality will become poorer. When this happens, the lamp should be replaced with a new one. p.46
Projection stops automatically

Is sleep mode active?

When "Sleep Mode" has been set to On, the lamp turns off automatically if no signal is input for about 30 minutes, and the projector switches to standby mode. Press the button on the remote control or the button on the projector's control panel to turn the projector's power back on. To cancel the sleep mode setting, change "Sleep Mode" menu command to "Off". "Settings" - "Sleep Mode" p.33
Have you pressed the [Power] button? Is "Child Lock" set to "On"?

Press panel.

on the remote control or
on the projector's control
If the "Child Lock" menu command is set to "On", press on the projector's control panel for about 3 seconds or press on the remoto control to turn the power on. "Settings" - "Child Lock" p.33
Is "Operation Lock" set to "On"? If the "Operation Lock" menu command is set to "On", all buttons on the projectors control panel are disabled. Press on the remote control. "Settings" - "Operation Lock" p.33 Are all of the indicators switched off?

Securely tighten the lamp fixing screws.

Install the lamp cover.

Resetting the lamp operating time
The lamp operating time must always be reset after the lamp has been replaced with a new one. The projector has a built-in counter which keeps track of the lamp operating time. When the cumulative operating time reaches a certain point, it causes the replacement warning message to be displayed. Press to turn on the power. Press to display the configuration menu.
Remove the old air filter.
Insert the new air filter.
Install the air filter cover.
Loosen the lamp fixing screws.

Remove the old lamp.

Insert the new lamp.

Pull out straight.

Make sure that it faces the correct way.
Install the lamp and the lamp cover securely. The lamp will not turn on if the lamp or the lamp cover is not installed correctly. This product includes a lamp component that contains mercury (Hg). Please consult your local regulations regarding disposal or recycling. Do not dispose of it with normal waste.
Select "Reset Lamp Hours" from the "Reset" menu.
Select "Yes" and then press.
Optional Accessories / Consumables
The following optional accessories / consumables are available for purchase if required. This list of optional accessories and consumables is current as of December, 2006. Details of accessories are subject to change without notice. Varies depending on country of purchase.
Optional Accessories 50" Portable Screen ELPSC06
Consumables Lamp Unit (1 spare lamp, 1 spare screwdriver) Use as a replacement for spent lamps. Air Filter Set (1 air filter) Use as a replacement for old air filters. ELPAF09 ELPLP39
A compact screen which can be carried easily. (Aspect 4:3) 60" Portable Screen 80" Portable Screen 100" Portable Screen A portable roll-type screen. (Aspect 4:3) VGA-HD15 PC Cable (1.8 m) VGA-HD15 PC Cable (3 m) VGA-HD15 PC Cable (20 m) ELPKC02 ELPKC09 ELPKC10 ELPSC07 ELPSC08 ELPSC10
(For mini D-Sub 15-pin/mini D-Sub 15-pin) Use to connect the projector to a computer. Ceiling Mount* ELPMB20
(with ceiling plate) Use when installing the projector to a ceiling. Celling Pipe 600 (600 mm/white)* ELPFP07
Use when installing the projector to a high ceiling or a ceiling with veneer panels. * A special method of installation is required in order to suspend the projector from the ceiling. Please contact the place of purchase if you would like to use this installation method.

List of Supported Monitor Displays
Depending on the setting, the output screen resolution will change slightly.

Component Video

16:9 : Aspect
Units: Dots Wide 19201080
Signal SDTV (525i, 60Hz) SDTV(625i, 50Hz) SDTV(525p) SDTV(625p) HDTV (750p) 16:9 HDTV(1125i) 16:9 HDTV(1125p) 16:9
Resolution * * * * 19201080
Aspect mode Normal 14401080

Full 19201080

Zoom 19201080

14401080

19201080

*Letterbox signal

Composite Video /S-Video

Units: Dots

Signal TV(NTSC ) TV(PAL , SECAM )

Resolution * *

Normal 14401080
Aspect mode Full Zoom 19201080 19201080

16:9 16:9

Wide 19201080
Computer image (analog RGB)
Units: Dots Signal VGA 60 VESA72/75/85, iMac*1 SVGA 56/60/72/ 75/85, iMac*1 XGA 60/70/75/ 85, iMac*1 WXGA60-1 WXGA60-2 SXGA 60 MAC13" MAC16" MAC19" Resolution Normal *640360 *800450 *1024576 *14401080 Full Aspect mode Zoom Wide 19201080 19201080
*1 Connection is not possible if the equipment does not have a VGA output port. *2 Letterbox signal It may be possible to project signals which are not listed in the above table. However, some functions may be limited in that case.
Input signal from the [HDMI] input port
Units: Dots Signal VGA 60 SDTV (525i, 60Hz) SDTV(525p) SDTV(625i, 50Hz) SDTV(625p) HDTV (750p) Resolution Normal *720360 *720360 *720432 *720432 *Full 19201080 Aspect mode Zoom 19201080 Wide 19201080 -

HDTV(1125i) HDTV(1125p)

*1 Connection is not possible if the equipment does not have a VGA output port. *2 Letterbox signal are input signals through the [SCART] input port. It may be possible to project signals which are not listed in the above table. However, some functions may be limited in that case.

Specifications

Product name Dimensions Panel size Display method Resolution Scanning frequencies
Home Projector EMP-TW(W) 124 (H) 310 (D) mm (not including feet) 0.74 inch wide Polysilicon TFT active matrix 2,073,600 pixels (1920 (W) 1080 (H) dots) 3 Analogue Pixel clock : 13.5 to 150 MHz Horizontal : 15 to 80 kHz Vertical Digital : 50 to 85 Hz Pixel clock : 13.5 to 150 MHz Horizontal : 15 to 80 kHz Vertical : 50 to 85 Hz Manual Manual (appox. 1 : 2.1) Manual (Maximums: Approx. 96% vertically, 47% horizontally) UHE lamp, 170 W, Model No.: ELPLPto 240V AC 50/60Hz 2.7 to 1.2A Power Consumption Operating: 245W(100 to 120V area), 240W(220 to 240V area) Standby: 4.0W(100 to 120V area), 5.0W(220 to 240V area) 0 to 2286m (0 to 7500ft.) +5 to +35C (No condensation)

SEIKO EPSON CORPORATION 2006. All rights reserved.

92 EPSON EMP-TW416900 www.epson.co.uk
Curvy, black, and dominated by its lens, Epsons EMP-TW1000 is a bit of a looker
HOME CINEMA CHOICE DECEMBER 2007

HCC149.epson 92

10/10/07 16:12:18

REVIEWS 93

Epson joins the Full HD parade
Theres more to Epson than printers, as this 1080p projector proves. Martin Pipe puts the EMP-TW1000 through its paces
ost people are likely to associate the Epson brand with printers and scanners, rather than home cinema gear. Yet, and this may come as a surprise, the company is actually the bone de world number one in projectors; supply and manufacture. And its a leading shareholder in the 3LCD consortium a tech utilised to the full with its rst, impressively specced, 1080p home cinema PJ. The EMP-TW1000 is a Full HD unit, with a native 16:9 resolution of 1920 x 1080 pixels. A good match, then, for Full HD sources such as Sky HD and high-def disc formats. The three LCD panels employ Epsons exclusive Crystal Clear Fine (C2Fine) technology the TW1000 is the rst PJ to make use of it. Here, the liquid crystals are aligned vertically when no voltage is applied. The result of this, once the effects of the polarising lters on either side of the liquid-crystal layer are factored in, is the (theoretical) elimination of light leakage Epson reckons this creates a pure jet black. Quite a claim, then. In addition to C2Fine is an auto-iris system. This changes the light intensity according to the source, thereby improving black performance. Hopefully, Epsons incarnation will improve on those of the competition with Mitsubishis similarly Full HD HC5000, for example, the jumps in light level can be rather off-putting. The 170W lamp is claimed to offer 1,700 hours of life or 3,000 if you select the low-power economy mode.
Then theres Epsons Cinema Filter, which effectively optimises the picture for differing lighting conditions. In an ideal world, there would be only one lighting condition completely dark but in the real world, things are not that simple. The six settings include dynamic for lighter rooms, natural and theatre black for darker environments.
Product: Full HD LCD projector, with HDMI1.3 input and shortthrow lens Positioning: Top of Epsons current range of consumer projectors Peers: Mitsubishi HC5000; Optoma HD80 Infocus IN78

Black is back

Talking of all things dark, the glossy black casework of the EMP-TW1000 is something to behold. The organic curves bestow a high-end appearance that deny its printer-manufacturer origins. In other words, you could
swap the badge for that of a more established homecinema marque and most would be none the wiser.
Also worthy of note is the 2.1x zoom lens, which is equipped with a lever-operated wide-angle lensshift function that operates horizontally and vertically. Not everyone can place the projector in its optimal position, and a lens shift can compensate for such eventualities with minimal image distortion (unlike keystone correction, which this projector doesnt have). This lens is a short-throw type; designed with small rooms in mind (well, it does hail from Japan!), it will yield 100in pictures at a distance of only 3m. To help you register the projected picture on the screen correctly, theres an on-board pattern generator. This is also useful for initial setting of focus.

Connectivity meets all expectations. Both component and HDMI are present, and will go all the way to 1080p. 480i and 576i (standard-def interlaced) can be fed into the HDMI port, as can 48Hz progressive video. A strong contender, then, for the new EICTA HD Ready 1080p logo that few are currently aware of. The HDMI input supports the latest 1.3 standard; the EMP-TW1000 uses 10-bit video processing (although not the 12-bit or 16-bit specically allowed by HDMI 1.3) for improved colour depth. This will really come into its own with PC users and latest-generation games consoles like the PlayStation 3. On the subject of PCs, a standard VGA port is included. But if your computer permits it use the HDMI input (bringing in DVI adaptors and switchboxes where necessary!). Also somewhat old-tech is the RS-232 serial port, which Epson has provided for system integration. Input selection is easy, the supplied handset dedicating buttons to each. This handset is backlit, but even with fresh batteries the lighting in question is rather dim. Full control of the PJ is possible without the remote but the in-built controls will be somewhat useless if the projector is ceilng-mounted. Most projectors of any note include some kind of bought-in video processing, and the EMP-TW1000 is no exception here. Rather than the usual Silicon Optix or Faroudja chipsets, though, Epson has plumped for PixelWorks DNX solution to carry
DECEMBER 2007 HOME CINEMA CHOICE

HCC149.epson 93

10/10/07 16:12:22

94 REVIEWS

Specifications
HD Ready: YES exceeds specification Progressive-scan: YES 480p, 576p, 720p and 1080p supported Composite:YES 1 input S-video: YES 1 input Component video: YES 1 input HDMI/DVI: YES HDMI 1.3 PC input: YES 1 D-sub 15-pin (VGA, RGB/ HV); configurable for component or Scart Dimensions: 406(w) x 124(h) x 310(d)mmmm Weight: 5.6kg Features: LCD technology; 1920 x 1080 resolution; 1,200 Lumens brightness (claimed); contrast 12,000:1 (claimed);RGB Scart input; horizontal/vertical lens shift; 4x aspect ratios (normal/full-screen/ zoom/wide); 100% scaling option; C2 Fine LCD; gamma and colour temperature adjustments; Epson Super White; 6x picture presets; autoiris mode; 30 150in; 2.1x short-throw zoom lens; RS232 control; 12V screentrigger output; pattern generator; input info display; 170W lamp; Up to 3000 hours lamplife (economy mode) 10-bit signal processing

Plug and play: The D-Sub input allows for PC connection
out deinterlacing and scaling duties. The setup menus allow plenty of tweaks, including output scaling (which can be effectively bypassed in the 100% setting ideal for native high-def sources), noise reduction, motion-detection and lm/video mode. Other menus provide the usual conguration parameters, including ceiling and rear-projection, and plenty of video adjustments. Among them are skin-tone, colour temperature, and comprehensive gamma adjustment, plus Epsons Super White mode, which tames overexposure in bright areas. Your video tweaks are stored on a per-input basis and there are ten overall memory banks to choose from. As a result, you can optimise picture quality for each of your sources.

Performance

After installing and calibrating the EMP-TW1000 to ISF standards, the viewing experience could begin. I started off with Blu-ray, in the form of Casino Royale undoubtedly one of the best releases to date on this hi-def format. Two things stood out. First of all, the portrayal of detail is exquisite. The grain of the
The movies exotic location-shooting, meanwhile, shows off the EMPTW1000s ability to reproduce colours with utter beauty. Motion blur never proves to be a problem, regardless of whether the source material is hi-def, DVD or digital TV. The auto-iris feature also works well, with no signicant jumps in brightness. Pictures were also free of noise, pixellation or other selfgenerated forms of artefacting. Perfection, alas, is not attained. For a start, shadow detail and overall black levels are a bit lacking just what is Epsons idea of jet black? A very dark grey, quite obviously. Another problem is that no control over aspect ratio is possible with HD sources; the presumption is that all hi-def material is in widescreen, but what about upscaled DVD material? Not all is agged correctly. Then theres the SD performance; pictures here are a tad on the soft side the use of HDMI does, however, minimise this effect.
A: Pre-calibration colour temperature was close, but post calibration it was almost dead on 6500K B: However, slightly high readings for red, blue and particularly green suggest an unnatural colour palette Before calibration Colour temperature: 6,915K Luminance: 288.4fL After calibration Colour temperature: 6,548K Luminance: 969fL

Conclusion

There are better Full HD projectors, but they tend to be signicantly more expensive than EMP-TW1000. The black-level limitations can perhaps be overlooked with this in mind, especially when the featureset, input exibility, excellent colour delity and potential for true-to-life detail are also factored in. This unit should denitely be on the shortlist of those seeking Full HD on a budget

VERDICT

Epson EMP-TW1000 2,600 Approx Highs: Beautiful colour; impressive detail; flexible configuration Lows: Disappointing black level; no HD aspect-ratio selection Performance: Design: Features:
tense black-and-white ashback sequence that kicks off the movie is so lmic, you can almost hear the gate-chatter.
Similarly impressive is the ght on the sinking Venetian building; all of the complex textures are conveyed with uncanny believability and depth.

Overall:

HCC149.epson 94

10/10/07 16:12:23