Reviews & Opinions
Independent and trusted. Read before buy Abit SG-80!

Abit SG-80

Manual

Download (English)
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Abit SG-80About Abit SG-80
Here you can find all about Abit SG-80 like manual and other informations. For example: motherboard.

Abit SG-80 manual (user guide) is ready to download for free.

On the bottom of page users can write a review. If you own a Abit SG-80 please write about it to help other people.

 

[ Report abuse or wrong photo | Share your Abit SG-80 photo ]

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

Comments to date: 1. Page 1 of 1. Average Rating:
arnechaa 8:04pm on Saturday, May 29th, 2010 
AGP support along with SATA support as well. Also two IDE connectors also Board is unstable with Pentium D 540.

Comments posted on www.ps2netdrivers.net are solely the views and opinions of the people posting them and do not necessarily reflect the views or opinions of us.

 

Documents

doc0

(SG-80, SG-81) Intel Pentium 4 System Board Socket 775 Users Manual

SG-80 Series

Rev. 1.00
Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, incidental or consequential damages arising from any defect or error in this manual or product. Product names appearing in this manual are for identification purpose only and trademarks and product names or brand names appearing in this document are property of their respective owners. This document contains materials protected under International Copyright Laws. All rights reserved. No part of this manual may be reproduced, transmitted or transcribed without the expressed written permission of the manufacturer and authors of this manual.

Table of Contents

Chapter 1.

1.1. 1.2. 1.3. 1.4.

Introduction.. 1-1
Features & Specifications.. 1-1 Layout Diagram (SG-80)... 1-3 Layout Diagram (SG-81)... 1-4 Jumpers & Connectors Description.. 1-5

Chapter 2.

2.1. 2.2. 2.3.

Hardware Setup... 2-1

CPU Socket... 2-1 System Memory... 2-2 Connectors, Headers, and Switches.. 2-3 2.3.1. ATX Power Connectors (ATX_POWER, ATX12V) 2-3 2.3.2. FAN Connectors (CPUFAN, SYSFAN, PWRFAN). 2-4 2.3.3. CMOS Memory Clearing Header (CCMOS). 2-5 2.3.4. Front Panel Switches & Indicators Connection Headers (PANEL1)... 2-6 2.3.5. Additional USB Port Connection Header (USB3, USB4)... 2-7 2.3.6. Front Panel Audio Connection Header (FPIO-AUDIO1).. 2-8 2.3.7. Accelerated Graphics Port Slot (AGP1). 2-9 2.3.8. Internal Audio Source Connectors (CD1, AUX1). 2-10 2.3.9. Floppy Disk Drive Connector (FDC). 2-11 2.3.10. IDE Disk Drive Connectors (IDE1, IDE2). 2-12 2.3.11. Serial ATA connectors (SATA1, SATA2).. 2-13 2.3.12. External I/O Panel... 2-14

Chapter 3.

BIOS Setup.. 3-1
About the Setup Utility... 3-1 3.1.1. The Standard Configuration.. 3-1 3.1.2. Entering the Setup Utility... 3-2 3.1.3. Updating the BIOS... 3-3

Users Manual

Using BIOS... 3-4 3.2.1. Standard CMOS Features... 3-4 3.2.2. Advanced BIOS Features... 3-7 3.2.3. Advanced Chipset Features. 3-10 3.2.4. Integrated Peripherals.. 3-14 3.2.5. Power Management Setup.. 3-18 3.2.6. PnP/PCI Configurations.. 3-20 3.2.7. PC Health Status... 3-22 3.2.8. Frequency Control.. 3-23 3.2.9. Load Fail-Safe Defaults Option.. 3-23 3.2.10. Load Optimized Defaults Option.. 3-24 3.2.11. Set Password... 3-24 3.2.12. Save & Exit Setup Option.. 3-25 3.2.13. Exit Without Saving.. 3-25

Chapter 4.

Driver Installation.. 4-1

Setup Items.... 4-2

Appendix A. How to Get Technical Support. A-1

Introduction

1.1. Features & Specifications
Designed for Intel 90nm Pentium 4/Celeron D LGA775 Processors with 800/533 MHz FSB Supports Intel Hyper-Threading Technology SIS 661FX/ 964 (L) Two 184-pin DIMM sockets Supports DDR400 non-ECC un-buffered memory Supports maximum memory capacity up to 2GB Integrated SIS Mirage Graphics GPU high performance 256-bit 3D engine and 2D Accelerator Serial ATA 1.5Gbps data transfer rate Support SW RAID 0/ 1/ JBOD Onboard 10/100 PHY On board 5.1 channels Audio CODEC 1x AGP 8X/4X slot. 3x PCI slots 1x Floppy Port supports up to 2.88MB 2x Ultra DMA 133/100/66/33 Connectors 2x Serial ATA 1.5Gbps Connectors (Option) 2x USB 2.0 headers (Each header support two USB 2.0 devices) 1x FP-Audio header, 1 x CD-IN, 1 x AUX-IN

Chipset Memory

Graphic

SATA 150 (Option)

LAN Audio Internal I/O Connectors

Chapter 1

Back Panel I/O
1x PS/2 Keyboard, 1x PS/2 Mouse 1x Serial Port, 1x Parallel Port, 1x VGA connector 4x USB 2.0, 1x RJ-45 LAN Connector 1x Audio connectors (Line-out, Line-in, MIC-in) Micro ATX form factor (244mm x 244mm)
Miscellaneous Product List
Model SG-80 SG-81 Chipset SIS 661FX + 964 SIS 661FX + 964L Features 10/100 LAN + SATA 10/100 LAN
All brand names and trademarks are the property of their respective owners. This motherboard is customized for certain system configurations; and may not fit system integration in all DIY ways. Before integrating this product, please check ABIT web site for recommended device listings, or contact sales/tech. support people. Specifications and information contained herein are subject to change without notice.
1.2. Layout Diagram (SG-80)
1.3. Layout Diagram (SG-81)
1.4. Jumpers & Connectors Description
Jumpers CCMOS Description CMOS Memory Clearing Header Default Setting Pins 2-3 Closed (Normal)
Connectors AGP1 ATX_POWER ATX12V CD1/AUX1 CPUFAN SYSFAN/PWRFAN DIMM1/DIMM2 FDC1 FPIO_AUDIO1 IDE1/IDE2 PANEL1 PCI1/PCI2/PCI3 SATA1/SATA2 USB3/USB4
Description Accelerated Graphics Port Slot ATX Power Connectors Internal Audio Connectors CPU Fan Power Connector System/Power Fan Power Connectors DDR DIMM Slots Floppy Disk Drive Connector Front Panel Audio Connection Header Hard Disk Drive Connectors Front Panel Switch Connection Headers 32bit/33MHz PCI Slots Serial ATA connectors Additional USB Port Connection Headers

Hardware Setup

2.1. CPU Socket
This server board provides one 775-pin Zero Insertion Force (ZIF) socket to install the Intel Pentium 4 CPU.

Chapter 2

2.2. System Memory
This system board provides two 184-pin DDR DIMM slots for un-buffered and non-ECC modules with memory size expansible up to 2GB (DDR400). DIMM DIMM Module 256MB, 512MB, 1GB 256MB, 512MB, 1GB Total System Memory Total Memory 256MB ~ 1GB 256MB ~ 1GB 256MB ~ 2GB
2.3. Connectors, Headers, and Switches
All the connectors, headers and switches mentioned here are depending on your system configuration. Some features you may (or may not) have to connect or to configure depending on the peripherals you have connected. WARNING: Always power off the computer and unplug the AC power cord before adding or removing any peripheral or component. Failing to so may cause severe damage to your system board and/or peripherals. Plug in the AC power cord only after you have carefully checked everything.

2.3.1.

ATX Power Connectors (ATX_POWER, ATX12V)
This connector provides the connection to ATX12V power supply.

2.3.2.

FAN Connectors (CPUFAN, SYSFAN, PWRFAN)
These connectors each provide power to the cooling fans installed in your system. CPUFAN: Power connector for CPU cooling fan SYSFAN, PWRFAN: Power connector for System and Power Fan
WARNING: These fan connectors are not jumpers. DO NOT place jumper caps on these connectors.

2.3.3.

CMOS Memory Clearing Header (CCMOS)
This header uses a jumper cap to clear the CMOS memory. Pin 2-3 shorted (default): Normal operation. Pin 1-2 shorted: Clear CMOS memory.
ATTENTION: Turn the system power off first (including the +5V standby power) before clearing the CMOS memory. Failing to do so may cause your system to work abnormally or malfunction.

2.3.4.

Front Panel Switches & Indicators Connection Headers (PANEL1)
These headers are used for connecting switches and LED indicators on the chassis front panel. The mark + align to the pin in the figure below stands for positive polarity for the LED connection.
Definition HD LED + HD LED RESET RESET Reserved

Pin 10

Definition Message LED + Message LED Power Switch Power Switch NC

2.3.5.

Additional USB Port Connection Header (USB3, USB4)
These headers each provide 2 additional USB 2.0 ports connection through an USB cable designed for USB 2.0 specifications.
Pin Signal Name 9 USBPWR USBPWR USB_FP_P0USB_FP_P1USB_FP_P0+ USB_FP_P1+ GND GND Key
Function Front Panel USB Power Front Panel USB Power USB Port 0 Negative Signal USB Port 1 Negative Signal USB Port 0 Positive Signal USB Port 1 Positive Signal Ground Ground No pin NC

2.3.6.

Front Panel Audio Connection Header (FPIO-AUDIO1)
This header provides the connection to audio connector at front panel. To use the audio connector at front panel, remove all the jumpers on this header, and then connect to front panel by the extension cable provided with the chassis. To use the audio connector at rear panel, disconnect the extension cable, attach the jumpers back at pin 5-6, and pin 9-10 (default setting).

Pin 9 10

Signal Name AUD_MIC AUD_GND AUD_MIC_BIAS AUD_VCC Filtered AUD_F_R AUD_RET_R REVD Key AUD_F_L AUD_RET_L
Function Front Panel Microphone input signal Ground used by Analog Audio Circuits Microphone Power +5V used by Analog Audio Circuits Right Channel audio signal to Front Panel Right Channel Audio signal to Return from Front Panel Reserved No Pin Left Channel Audio signal to Front Panel Left Channel Audio signal to Return from Front Panel

2.3.7.

Accelerated Graphics Port Slot (AGP1)
This slot supports an optional AGP graphics card up to AGP 8X/4X mode. ATTENTION: This motherboard does not support 3.3V AGP cards. Use only 1.5V or 0.8V AGP cards.

2.3.8.

Internal Audio Source Connectors (CD1, AUX1)
These connectors connect to the audio output of internal CD-ROM drive or add-on card.

2.3.9.

Floppy Disk Drive Connector (FDC)
This connector supports two standard floppy disk drives via a 34-pin 34-conductor ribbon cable. Connecting the Floppy Disk Drive Cable: 1. Install one end of the ribbon cable into the FDC connector. The colored edge of the ribbon cable should be aligned with pin-1 of FDC connector. 2. Install the other end(s) of ribbon cable into the disk drive connector(s). The colored edge of the ribbon cable should be also aligned with pin-1 of disk drive connector. The endmost connector should be attached to the drive designated as Drive A.

2.3.10.

IDE Disk Drive Connectors (IDE1, IDE2)
These IDE ports each connects up to two IDE drives at Ultra ATA/100 mode by one 40-pin, 80-conductor, and 3-connector Ultra ATA/66 ribbon cables. Connect the single end (blue connector) at the longer length of ribbon cable to the IDE port on system board, and the other two ends (gray and black connector) at the shorter length of the ribbon cable to the connectors on hard drives. NOTE: The red line on the ribbon cable should be aligned with pin-1 on this connector.

2.3.11.

Serial ATA connectors (SATA1, SATA2)
These connectors are provided to attach one Serial ATA device at each channel via Serial ATA cable.

2.3.12.

External I/O Panel
Mouse: PS/2 mouse connector. Keyboard: PS/2 keyboard connector. LPT1: Parallel port connector. COM1: Serial port connector. VGA1: Monitor signal connector. USB1/USB2: USB 2.0 connectors. LAN1:10/100Mbps LAN connectors. AUDIO: Mic In: Connects to the plug from external microphone. Line In: Connects to the line out from external audio sources. Line Out: Connects to the front left and front right channel in the 5.1-channel or regular 2-channel audio system.

BIOS Setup

3.1. About the Setup Utility
The computer uses the latest Award BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS. The BIOS (Basic Input and Output System) Setup Utility displays the systems configuration status and provides you with options to set system parameters. The parameters are stored in battery-backed-up CMOS RAM that saves this information when the power is turned off. When the system is turned back on, the system is configured with the values you stored in CMOS. The BIOS Setup Utility enables you to configure: Hard drives, diskette drives and peripherals Video display type and display options Password protection from unauthorized use Power Management features
The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options. This chapter provides explanations for Setup Utility options.

3.1.1.

The Standard Configuration
A standard configuration has already been set in the Setup Utility. However, we recommend that you read this chapter in case you need to make any changes in the future. This Setup Utility should be used: when changing the system configuration when a configuration error is detected and you are prompted to make changes to the Setup Utility when trying to resolve IRQ conflicts when making changes to the Power Management configuration when changing the password or making other changes to the Security Setup

Chapter 3

3.1.2.
Entering the Setup Utility
When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are completed, the following message appears: Press <DEL> to enter SETUP Pressing the <Delete> key accesses the BIOS Setup Utility:
BIOS Navigation Keys The BIOS navigation keys are listed below: KEY ESC +/-/PU/PD F10 F1 F5 F6 F7 FUNCTION Exits the current menu Scrolls through the items on a menu Modifies the selected fields values Saves the current configuration and exits setup Displays a screen that describes all key functions Loads previously saved values to CMOS Loads a minimum configuration for troubleshooting Loads an optimum set of values for peak performance

3.1.3.

Updating the BIOS
You can download and install updated BIOS for this motherboard from the manufacturers Web site. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install new BIOS as follows: 1. If your motherboard has a BIOS protection jumper, change the setting to allow BIOS flashing. 2. If your motherboard has an item called Firmware Write Protect in Advanced BIOS features, disable it. (Firmware Write Protect prevents BIOS from being overwritten.) 3. Create a bootable system disk. (Refer to Windows online help for information on creating a bootable system disk.) 4. Download the Flash Utility and new BIOS file from the manufacturers Web site. Copy these files to the system diskette you created in Step 3. 5. Turn off your computer and insert the system diskette in your computers diskette drive. (You might need to run the Setup Utility and change the boot priority items on the Advanced BIOS Features Setup page, to force your computer to boot from the floppy diskette drive first.) 6. At the A:\ prompt, type the Flash Utility program name and press <Enter>. 7. Type the filename of the new BIOS in the File Name to Program text box. Follow the onscreen directions to update the motherboard BIOS. 8. When the installation is complete, remove the floppy diskette from the diskette drive and restart your computer. If your motherboard has a Flash BIOS jumper, reset the jumper to protect the newly installed BIOS from being overwritten.

3.2. Using BIOS

When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>. Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for information. Some options (marked with a triangle ) lead to submenus that enable you to change the values for the option. Use the cursor arrow keys to scroll through the items in the submenu. In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a triangle.

3.2.1.

Standard CMOS Features
This option displays basic information about your system.
Date and Time The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility.
IDE Devices (None) Your computer has two IDE channels (Primary and Secondary) and each channel can be installed with one or two devices (Master and Slave). Use these items to configure each device on the IDE channel. This motherboard features two SATA connectors supporting two SATA drives. SATA refers to Serial ATA (Advanced Technology Attachment), the standard interface for the IDE hard drives which are currently used in most PCs. Press <Enter> to display the IDE submenu:
IDE HDD Auto-Detection Press <Enter> while this item is highlighted to prompt the Setup Utility to automatically detect and configure an IDE device on the IDE channel. NOTE: If you are setting up a new hard disk drive that supports LBA mode, more than one line will appear in the parameter box. Choose the line that lists LBA for an LBA drive. IDE Channel 1/2 Master/Slave/ IDE Drive(Auto) Leave this item at Auto to enable the system to automatically detect and configure IDE devices on the channel. If it fails to find a device, change the value to Manual and then manually configure the drive by entering the characteristics of the drive in the items described below. Users Manual
Refer to your drives documentation or look on the drive casing if you need to obtain this information. If no device is installed, change the value to None. NOTE: Before attempting to configure a hard disk drive, ensure that you have the configuration information supplied by the manufacturer of your hard drive. Incorrect settings can result in your system not recognizing the installed hard disk. Access Mode (Auto) This item defines ways that can be used to access IDE hard disks such as LBA (Large Block Addressing). Leave this value at Auto and the system will automatically decide the fastest way to access the hard disk drive. Press <Esc> to return to the Standard CMOS Features page. Drive A/Drive B (1.44M, 3.5 in./None) These items define the characteristics of any diskette drive attached to the system. You can connect one or two diskette drives. Floppy 3 Mode Support (Disabled) Floppy 3 Mode refers to a 3.5-inch diskette with a capacity of 1.2 MB. Floppy 3 Mode is sometimes used in Japan. Video (EGA/VGA) This item defines the video mode of the system. This motherboard has a built-in VGA graphics system; you must leave this item at the default value. Halt On (All, But Keyboard) This item defines the operation of the system POST (Power On Self Test) routine. You can use this item to select which types of errors in the POST are sufficient to halt the system. Base Memory, Extended Memory, and Total Memory These items are automatically detected by the system at start up time. These are display-only fields. You cannot make changes to these fields.

3.2.2.

Advanced BIOS Features
This option defines advanced information about your system.

CPU Feature

Scroll to this item and press <Enter> to view the following screen: Users please note that this function is only available for Prescott CPUs.
Thermal Management This item displays CPUs temperature and enables you to set a safe temperature to Prescott CPU. TM2 Bus Ratio This item represents the frequency (bus ratio) of the throttled performance state that will be initiated when the on-die sensor goes from not hot to hot). TM2 Bus VID This item represents the voltage of the throttled performance state that will be initiated when the on-die sensor goes from not hot to hot. Limit CPUID MaxVal This item can support Prescott CPUs for old OS. Users please note that under NT 4.0, it must be set Enabled, while under WinXP, it must be set Disabled. NX BIOS Control When disabled, forces the NX feature flag to always return to 0.

Hard Disk Boot Priority

Scroll to this item and press <Enter> to view the following screen:
CPU L3 Cache (Enabled) This item is only available when processors support L3. Some high-end processors support L3. If the CPU do support L3, you may set this item to enable or disable. Leave this item at the default value for better performance. Hyper-Threading Technology (Enabled) This item is only available when the chipset supports Hyper-Threading and you are using a Hyper-Threading CPU. Quick Power On Self Test (Enabled) Enable this item to shorten the power on testing (POST) and have your system start up faster. You might like to enable this item after you are confident that your system hardware is operating smoothly. First/Second/Third Boot Device (Floppy/Hard Disk/CDROM) Use these three items to select the priority and order of the devices that your system searches for an operating system at start-up time. Boot Other Device (Enabled) When enabled, the system searches all other possible locations for an operating system if it fails to find one in the devices specified under the First, Second, and Third boot devices. Swap Floppy Drive [Disabled] If you have two floppy diskette drives in your system, this item allows you to swap the assigned drive letters so that drive A becomes drive B, and drive B becomes drive A. Boot Up Floppy Seek (Disabled) If this item is enabled, it checks the size of the floppy disk drives at start-up time. You dont need to enable this item unless you have a legacy diskette drive with 360K capacity. Boot Up NumLock Status (On) This item defines if the keyboard Num Lock key is active when your system is started.

AGP Data Rate (Auto) This item allows users to set the AGP Data Rate by, Auto, 1X, 2X, 4X, or 8X, depending on what speed the AGP card supports. Press <Esc> to return to the Advanced Chipset Features page.

OnChip AGP Control

VGA Share Memory Size (32M) This item allows you to select the shared memory size for VGA usage. Press <Esc> to return to the Advanced Chipset Features screen. System BIOS Cacheable (Disabled) This feature is only valid when the system BIOS is shadowed. It enables or disables the caching of the system BIOS ROM at F0000h-FFFFFh via the L2 cache. This greatly speeds up accesses to the system BIOS. Video RAM Cacheable (Disabled) This feature enables or disables the caching of the video RAM at A0000h-AFFFFh via the L2 cache.

3.2.4.

Integrated Peripherals
These options display items that define the operation of peripheral components on the systems input/output ports.

OnChip IDE Device

Internal PCI/IDE (Both) Use these items to enable or disable the internal PCI IDE channels that are integrated on the mainboard. IDE DMA Transfer Access (Enabled) This item allows you to enabled the transfer access of the IDE DMA. IDE Burst Mode (Enabled) This option, when enabled will instruct the system to send every write transaction to the write buffer. Burstable transactions then burst onto the PCI bus and nonburstable transactions do not. OnChip SATA Controller (Enabled) Enables or disables the onboard Serial ATA controller. Enable this item if you are to install SATA devices onboard. Serial ATA Mode (IDE) Use this item to define the onboard SATA mode. Set this item to RAID if you are to activate the RAID function of the SATA devices. Press <Esc> to return to the Integrated Peripherals screen.

OnChip PCI Device

OnChip USB Controller (Enabled) Enable this item if you plan to use the Universal Serial Bus ports on this mainboard. OnChip AC97 Controller (Enabled) Enables or disables the onboard AC97 audio function. Disable this item if you are going to install a PCI audio add-on card. OnChip LAN Controller (Enabled) Enables and disables the onboard LAN chip. LAN Boot ROM (Disabled) Use this item to enable and disable the booting from the onboard LAN or a network add-in card with a remote boot ROM installed.
BIOS Setup Press <Esc> to return to the Integrated Peripherals screen.

Onboard SuperIO Device:

Onboard FDC Controller (Enabled) This option enables the onboard floppy disk drive controller. Onboard Serial Port 1 (3F8/IRQ4) This option is used to assign the I/O address and interrupt request (IRQ) for onboard serial port1 (COM1). Onboard Parallel Port (378/IRQ7) This option is used to assign the I/O address and interrupt request (IRQ) for the onboard parallel port. Parallel Port Mode (ECP) Enables you to set the data transfer protocol for your parallel port. There are four options: SPP (Standard Parallel Port), EPP (Enhanced Parallel Port), ECP (Extended Capabilities Port), and ECP+EPP. SPP allows data output only. Extended Capabilities Port (ECP) and Enhanced Parallel Port (EPP) are bi-directional modes, allowing both data input and output. ECP and EPP modes are only supported with EPP- and ECP-aware peripherals. Users Manual

3-18 ECP Mode Use DMA (3)
When the onboard parallel port is set to ECP mode, the parallel port can use DMA3 or DMA1. Press <Esc> to return to the Integrated Peripherals screen. Onboard 1394 Device (Enabled) Enables and disables the onboard IEEE 1394 controller. Init Display First (PCI Slot) Use this item to specify whether your graphics adapter is installed in one of the PCI slots or is integrated on the motherboard.

3.2.5.

Power Management Setup
This option lets you control system power management. The system has various power-saving modes including powering down the hard disk, turning off the video, suspending to RAM, and software power down that allows the system to be automatically resumed by certain events.
ACPI Suspend Type (S3(STR)) Use this item to define how your system suspends. In the default, S1(POS), the suspend mode is equivalent to a software power down. If you select S3 (STR), the suspend mode is a suspend to RAM, i.e., the system shuts down with the exception of a refresh current to the system memory. SG-80 Series
BIOS Setup Resume by USB from S3 (Disabled)
When set to Enabled, the system power will resume the system from a power saving mode if there is any USB port activity. Power On by PS2 Keyboard (Hot Key) This option enables you to allow the keyboard activity to awaken the system from power saving mode. Power On by PS2 Mouse (Disabled) This option enables you to allow the mouse activity to awaken the system from power saving mode. Wakeup By Ring (Disabled) Use this item to enable LAN or modem activity to wakeup the system from a power saving mode. Wakeup By PME# of PCI (Enabled) This item allows users to enable or disable PCI activity to wakeup the system from a power saving mode. Power Up by Alarm (Disabled) When set to Enabled, the following three fields become available: Month Alarm, Day of Month Alarm, and Time Alarm Upon arrival of the alarm time, it will instruct the system to wake up. When set to 0 (zero) for the day of the month, the alarm will power on your system every day at the specified time. Power Button Override: Under ACPI (Advanced Configuration and Power management Interface) you can create a software power down. In a software power down, the system can be resumed by Wake Up Alarms. This item lets you install a software power down that is controlled by the power button on your system. If the item is set to Instant-Off, then the power button causes a software power down. If the item is set to Delay 4 Sec. then you have to hold the power button down for four seconds to cause a software power down. Restore On AC Power Loss: This item selects the system action after an AC power failure. Users Manual

PIRQ_0 Use IRQ No. ~ PIRQ_7 Use IRQ No. [Auto] This item specifies the IRQ number manually or automatically for the devices installed on PCI slots.

3.2.7.

PC Health Status
On motherboards that support hardware monitoring, this item lets you monitor the parameters for critical voltages, critical temperatures, and fan speeds.
CPU Shutdown Temperature (Disabled) This item sets the temperature that would shutdown the system automatically in order to prevent system overheats. NOTE: This item only works for the OS with ACPI activated. System Component Characteristics These items allow end users and technicians to monitor data provided by the BIOS on this motherboard. You cannot make changes to these fields.

3.2.8.

Frequency Control
This item enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have installed in your system.
Auto Detect DIMM/PCI Clk (Enabled) When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI slots. Spread Spectrum (Enabled) If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system. Clock Control By (Auto) Use this item to set the CPU Host Clock frequency to Auto or by manual setting. Select Manual to activate the following items and set each item manually.

3.2.9.

Load Fail-Safe Defaults Option
This option opens a dialog box that lets you install fail-safe defaults for all appropriate items in the Setup Utility:
Press <Y> and then <Enter> to install the defaults. Press <N> and then <Enter> to not install the defaults. The fail-safe defaults place no great demands on the system and are generally stable. If your system is not functioning correctly, try installing the fail-safe defaults as a first step in getting your system working properly again. If you only want to install fail-safe defaults for a specific option, select and display that option, and then press <F6>.

Driver Installation

All the necessary drivers are included within the Drivers & Utilities CD that came packaged with your board. The display shown in the following figure should appear after inserting this CD into your CD-ROM drive, if not, enter [My Computer] [CD-ROM] Drive double click [autorun.exe]. Please follow the on-screen instruction.

Chapter 4

4.1. Setup Items
Drivers Install the drivers for Windows Operating System. Manual View the users manual in PDF file. Utility Click to enter the sub-screen for installing software like Acrobat Reader, Award Flash, DirectX, and LoFormat utility. Browse CD Browse the contents of this CD-ROM. Close Exit the CD setup Items Menu.
How to Get Technical Support
Appendix A. How to Get Technical Support
(From our website) http://www.abit.com.tw (In North America) http://www.abit-usa.com (In Europe) http://www.abit.nl
Thank you for choosing ABIT products. ABIT sells all our products through distributors, resellers and system integrators; we have no direct sales to end-users. Before sending email for tech support please check with your resellers or integrators if you need any services, they are the ones who sold you your system and they should know best as to what can be done, how they serve you is a good reference for future purchases. We appreciate every customer and would like to provide the best service to you. Providing fast service to our customers is our top priority. However we receive many phone calls and a huge amount of email from all over the world. At the present time it is impossible for us to respond to every single inquiry. Therefore it is quite possible that if you send an email to us that you may not receive a response. We have done many compatibility tests and reliability tests to make sure our products have the best quality and compatibility. In case you need service or technical support, please understand the constraint we have and always check with the reseller who sold the product to you first. To expedite service, we recommend that you follow the procedures outlined below before contacting us. With your help, we can meet our commitment to provide the best service to the greatest number of ABIT customers: 1. Check the Manual. It sounds simple but we have taken a lot of care in making a well-written and thorough manual. It is full of information that doesn't only pertain to motherboards. The CD-ROM included with your board will have the manual as well as drivers. If you don't have either one, go to our Program Download Area of the Website or FTP server. Download latest BIOS, software or drivers. Please go to our Program Download area on our Website to check to see if you have the latest BIOS. They are developed over periods of time to fixes bugs or incompatibilities. Also please make sure you have the latest drivers from your peripheral cards makers! Check the ABIT Technical Terms Guide and FAQ on our Website. We are trying to expand and make the FAQs more helpful and information rich. Let us know if you have any suggestions. For hot topics check out our HOT FAQ! Internet Newsgroups. They are a great source of information and many people there can offer help. ABIT's Internet News group, alt.comp.periphs.mainboard.abit, is an ideal forum for the public to exchange information and discuss experiences they have had with ABIT products. Many times you will see that your question has already been asked before. This is a public Internet news group and it is reserved for free discussions. Here is a list of some of the more popular ones:

North America and South America ABIT Computer (U.S.A.) Corporation 45531 Northport Loop West, Fremont CA, 94538, U.S.A. Tel: 1-510-623-0500 Fax: 1-510-623-1092 Sales: sales@abit-usa.com Latin America Sales: ventas@abit-usa.com Marketing: marketing@abit-usa.com Web Site: http://www.abit-usa.com 46808 Lakeview Blvd. Fremont, CA 94538, U.S.A.
RMA Center UK and Ireland
ABIT Computer (U.K.) Corporation Ltd. Unit 3, 24-26 Boulton Road, Stevenage, Herts SG1 4QX, UK Tel: 44-1438-228888 Fax: 44-1438-226333 E-mail: sales@abitcomputer.co.uk AMOR Computer B.V. (ABIT's European Office)
Germany and Benelux (Belgium, Netherlands, Luxembourg), France, Italy, Spain, Portugal, Greece, Denmark, Norway, Sweden, Finland, and Switzerland Austria, Czech, Romania, Bulgaria, Slovakia, Croatia, Bosnia, Serbia, and Macedonia Shanghai
Jan van Riebeeckweg 15, 5928LG, Venlo,
The Netherlands Tel: 31-77-3204428 Fax: 31-77-3204420 Sales: sales@abit.nl Web Site: http://www.abit.nl Asguard Computer Ges.m.b.H Schmalbachstrasse 5, A-2201 Gerasdorf / Wien, Austria Tel: 43-1-7346709 Fax: 43-1-7346713 E-mail: asguard@asguard.at ABIT Computer (Shanghai) Co. Ltd. Tel: 86-21-6235-1829 Fax: 86-21-6235-1832 Web Site: http://www.abit.com.cn ABIT Computer (Russia) Co. Ltd. Sales: sales@abit.ru Info: info@abit.ru Web Site: http://www.abit.ru ABIT Computer (Poland) Co. Ltd. Przedstawicielstwo w Polsce ul. Wita Stwosza 28, 50-149 Wrocaw Tel: 65 / 66 Fax: 87 Web Site: http://www.abit4u.jp ABIT Computer Corporation No. 323, Yang Guang St., Neihu, Taipei, 114, Taiwan Tel: 886-2-8751-8888 Fax: 886-2-8751-3382 Sales: sales@abit.com.tw Marketing: market@abit.com.tw Web Site: http://www.abit.com.tw

Russia and CIS

Poland
Japan Taiwan Head Office (Serving all other territories not listed above. Taiwan is 8+ GMT time, and may have different holiday calendar from yours.)

Technical Support Form

Company Name: Contact Person: E-mail Address: Model Motherboard Model No. OS/Application * * BIOS ID # DRIVER REV * Phone Number: Fax Number:
Hardware Name CPU HDD CD-ROM-Drive System Memory IDE1 IDE2 IDE1 IDE2

Brand *

Specifications

ADD-ON CARD

Problem Description:

 

Tags

NEC 411I Motorola W490 CCD-TR918E DCR-PC350 System RR-US065 2 II SCH-S179 600 PRO SDM-N50PS PCG-GRV616G KX-FP205G Magnia Z310 XR-3753 UE-40C5100 XM600 America Elro C950 DX130-JD Quad 44 Server C3510 Motherboard DVD 800 NV-GS33 KCA-420I-i-pod-space-interface 42PC3D-UE Yamaha QR10 Animal Tecra M7 EX-Z50 CF-5100 TE-100 Telescope 73A 1098 S KD-SX925R Control EB-GD93 Unlimted Gpsmap 495 DSC-W215 DR-Z125L Ericsson Zylo RDR-HXD760 90-250MM Sensor 500 Stand PT-8 Labelmanager 220P RX-V3000RDS B-2 PRO TD4112W Ideapad V460 KEH-P6100RDS PDW7000 Sp7000 Samsung I80 DG-stomp Alum10N 330551 AJ3150-00W S1410 Chatbot Motorazr V3R Brio Sing UE40C5000 NA168VX2 G-8000 R0902 Powerbank H500 SR2000 Manager Plus NW-S718F CP730 AVR85 BT2500 TCP42C2 TH-50PZ70E Control NX9000 RT-21FA32X PS50B550 DSP 260 DCR-DVD905E DMR-E95HEG Dopod D600 EV5DVD 3-gold Volt SP90 HTS3366 93 Chorus Lexmark W820 MCD288 XM-GTX1852 Explorer PRO DVD-1000 ICD-B500 BD239R Plus M-5 BJV180 YP-P2AB

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101