NOTICE:

1. The changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibility of the user to correct such interference. As an ENERGY STAR Partner our company has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

WARNING:

To prevent fire or chock hazard, do not expose the monitor to rain or moisture. Dangerously high voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.

PRECAUTIONS

Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, Swimming pool or in a wet basement. Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a trolley or stand recommended by the manufacture or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacture and follow the kit instructions. Slots and openings in the back and bottom of the cabinet area provided for ventilation. To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug or similar surface. Do not place the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided. The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug. Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges. Do not overload power strips and extension cords. Overloading can result in fire or electric shock. Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on the monitor. Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel. To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100-240V AC, Min. 3.5A. The wall socket shall be installed near the equipment and shall be easily accessible. For use only with the attached power adapter (output 12V DC) which have UL,CSA listed license

SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a problem.
Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness in the screen depending on the desktop pattern you use. The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the time. Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours.

Table of contents

Chapter 1 MONITOR FEATURE.9
Chapter 2 OPERATING INSTRUTION.15 Chapter 3 Machine assembly 21 Chapter 4 TROBLE SHOOTING.27 Chapter 5 CONNECTOR INFORMATION.29
Chapter 6 FRU LIST.30 Chapter 7 SCHEMATIC DIAGRAM 31

Chapter 1

Monitor Feature
Driving system Size Pixel pitch Viewable angle Brightness Contrast Ratio LCD Panel Input Response time Video Separate Sync H-Frequency V-Frequency Display Color Maximum Dot Clock Max Resolution Plug & Play ON Mode EPA ENERGY STAY Audio output Input Connector Input Video Signal Screen Size (Active) Power Source Environmental Considerations Weight (N.W.) Dimension OFF Mode TFT Color LCD 20.1 wide 0.258 mm 178(H) x 178 (V) degree LG panel: 300 cd/m2(typ) 600:1 (typ) 16ms (Tr+Tf) R,G,B Analog & DVI box (optional) H/V TTL 31-81KHZ 50-75HZ 16.7 million Colors 162MHz 1680X1050@60HZ VESA DDC2B <75W <3W Rated Power 5.0W rms(Per channel) D-Sub 15 pin, or DVI-D cable Analog : 0.7Vp-p,75OHM Horizontal : 433.4mm Vertical : 270.9mm 90~240 Vac, 50~60HZ Operating Temp : 5 to 40 degree ; Storage Temp : -20 to 60 degree ; Operating Humidity : 15% to 85% 6.8kg 510.3(W) x 443.9(H) x 206.6D) mm

Switch

* Power Switch * MENU/ENTER * / Volume * / Volume * Auto Adjust KEY

Function External Controls : Regulatory Compliance
* Contrast/brightness * Focus * Clock * H.Position * W.Position * Language * OSD Color temperature * OSD Position & Timeout * Auto Config * Input * Information * Reset * Exit cUL, FCC, TUV, CE, ISO13406-2

Timeings

The product has 29 memory modes in total. 19 modes are preset and 10 modes
are user definable. MODE NO. RESOLUTION x 640 x 640x640 x 480

Dot clock(MHz)

28.321

25.175

fh H-Total ( us ) H-Sync ( us ) H-B-P ( us ) H-Active ( us ) H-F-P ( us )
31.469kHz 31.78(900dots) 3.813(108dots) 1.907(54dots) 25.42(720dots) 0.636(18dots)
31.469kHz 31.778 (800 dots) 3.813 (96 dots) 1.907 (48 dots) 25.422 (640 dots) 0.636 (16 dots)
35.0kHz 28.571(864 dots) 2.116 (64 dots) 3.175 (96 dots) 21.164 (640 dots) 2.116 (64 dots)
37.861kHz 26.413 (832 dots) 1.270(40 dots) 4.064(128 dots) 20.317(640 dots) 0.762(24 dots)

- 10 -

fv V-Total (ms ) V-Sync ( ms ) V-B-P (ms ) V-Active ( ms ) V-F-P ( ms ) SYNC. H/V POLARITY SEP. SYNC
70Hz(70.087) 14.27(449 lines) 0.064(2 lines) 1.112(35 lines) 12.71(400 lines) 0.384(12 lines) -/+
60Hz (59.940) 16.683 (525 lines ) 0.064 (2 lines ) 1.049 (33 lines ) 15.253 (480 lines ) 0.317 ( 10 lines) -/-
66.7 HZ (66.667) 15.000 (525 lines ) 0.086 (3 lines ) 1.114 (39 lines ) 13.714 (480 lines ) 0.086 (3 lines ) +/+ Or -/-
72.809Hz 13.735(520 lines) 0.079(3 lines) 0.739(28 lines) 12.678(480 lines) 0.237(9 lines) -/-

MODE NO. RESOLUTION

37.500kHz 26.667(840 dots) 2.032 (64 dots) 3.810 (120 dots) 20.317 (640 dots) 0.508 (16 dots)
35.16kHz 28.44(1024 dots) 2.00(72 dots) 3.56(128 dots) 22.22(800 dots) 0.67(24 dots)

37.879kHz

46.875kHz
26.40 (1056 dots) 21.333 (1056dots) 3.200 (128 dots) 2.200 ( 88 dots) 20.00 ( 800 dots) 1.000 (40 dots) 1.616 (80 dots) 3.232 (160 dots) 16.162 (800 dots) 0.323 (16 dots)
75Hz (75) 13.333 (500 lines) 0.080 (3 lines) 0.427 (16 lines) 12.80 (480 lines) 0.027 ( 1 line ) -/-
56.25 17.78(625 lines) 0.06(2 lines) 0.63(22 lines) 17.07(600 lines) 0.03( 1 line) +/+
60Hz (60.316) 16.58 (628 lines) 0.106 (4 lines) 0.607 (23 lines) 15.84 (600 lines) 0.026 (1 line ) +/+

75Hz (75.000) 13.333 (625lines) 0.064 (3 lines) 0.448 (21 lines) 12.80 (600lines) 0.021 (1 line ) +/+

57.283

- 11 -
48.077kHz 20.80 (1040dots) 2.400 ( 120 dots) 1.280 (64 dots) 16.00 (800 dots) 1.120 (56 dots)
49.72kHz 20.11(1152 dots) 1.12(64 dots) 3.91(224 dots) 14.52( 832 dots ) 0.56(32 dots )
48.363kHz 20.677(1344 dots) 2.092(136 dots) 2.462(160 dots) 15.754(1024 dots) 0.369(24 dots)
56.48kHz 17.71(1328 dots) 1.81(136 dots) 1.92(144 dots) 13.65(1024 dots) 0.32(24 dots)
72Hz (72.188) 13.85 (666 lines) 0.125 (6 lines) 0.478 (23 lines) 12.48 (600 lines) 0.770 ( 37 +/+ line )
74.55Hz 13.41(667 lines) 0.06(3 lines) 0.78(39 lines) 12.55 (624 lines) 0.02(1 line) +/+
60.004Hz 16.666(806 lines) 0.124(6 lines) 0.600(29 lines) 15.880(768 lines) 0.062(3 lines) -/-
70.07Hz 14.27(806 lines) 0.11(6 lines) 0.51(29 lines) 13.60(768 lines) 0.05(3 lines) -/-

x 1024

60.02kHz 16.66(1312 dots) 1.22 (96 dots) 2.23 (176 dots) 13.00 (1024 dots) 0.20 (16 dots)
63.981kHz 15.630 (1688 dots) 1.037 (112 dots) 2.296 (248 dots) 11.852 (1280 dots) 0.444 (48 dots)

79.976KHz

67.5 KHz
12.504 (1688 dots) 14.815(1600 dots) 1.067 (144 dots) 1.837 (248 dots) 9.481 (1280dots) 0.119 (16 dots) 1.185(128 dots) 2.370(256 dots) 10.667(1152 dots) 0.593(64 dots)
fv V-Total (ms ) V-Sync ( ms ) V-B-P (ms ) V-Active ( ms ) V-F-P ( ms )
75.03Hz 13.33 (800 lines) 0.05 (3 lines) 0.47 (28 lines) 12.80 (768 lines) 0.02 (1 lines)

60.020Hz

75.025 Hz
75.06 Hz 13.333(900 lines) 0.044(3 lines) 0.474(32 lines) 12.800(864 lines) 0.015(1 lines)
16.661 (1066 lines) 13.329 (1066 lines) 0.047 ( 3 lines) 0.594 ( 38 lines) 16.005 (1024 lines) 0.016 (1 line )

- 12 -

0.038 (3 lines) 0.475 (38 lines) 12.804(1024 lines) 0.013 (1 lines)
SYNC. H/V POLARITY SEP. SYNC 17" MODE NO. RESOLUTION

x 1200

74.176
60.000 KHz 16.667 (1800dots) 1.037 ( 112 dots) 2.889 (312 dots) 11.852 (1280 dots) 0.889 (96 dots)
75.000 KHz 13.333 (2160 dots) 1.185 ( 192 dots) 1.877 (304 dots) 9.877 (1600 dots) 0.395 (64 dots)
44.955KHz 22.244 (1650dots) 0.539 ( 40 dots) 2.966 (220 dots) 17.256 (1280 dots) 1.483 (110 dots)

60.00Hz

60.00 Hz
59.94Hz 16.683 (750 lines) 0.111 (5 lines) 0.445 (20 lines) 16.016 (720 lines) 0.111 (5 lines) +/+
16.667 (1000 lines) 16.667 (1250 lines) 0.050 (3 lines) 0.600 (36 lines) 16.000 (960 lines) 0.017 ( 1 +/+ line ) 0.040 (3 lines) 0.613 (46 lines) 16.000 (1200 lines) 0.013 ( 1 +/+ line )

- 13 -

Monitor Block Diagram
+3.3V I/O A U +2.5V D +3.3V D _ _M LIB _D R _LV SA

+1.8V V _D I

+1.8V D _A C

+3.3V _PLL

+1.8V RE _CO

+3.3V _LBA C D

+3.3V D _LV SB

+3.3V D _LV S

+3.3V V _D I

+3.3V D _A C

D ITA D C IG L D 24A 02 (U A 12)

SD /SCL A

PO ERSW W ITCH A 1563(U IC 2) (U +2.5V 3) (U +3.3V 4) +12VFRO M (U +1.8V 6) PO ERB A W O RD

D I IN T V PU ( CN ) 8

A A GD C N LO D 24A 02 (U A 10)

RX , RX RX , RX 2 1, 0 C

/RESET MX A 809_1(U 8)

G 1601 (U M 5)

RED, G REEN, BLU , SD /SCL E A

V AIN T G PU ( CN ) 7

M SCL/SD STR A

I2C 24LC32SN(U 7)

FSD TA D R,FSB SEL0/1 A ,FSA D K FSCLK -/+,FSD M Q
FRA ESTO M RE M 2M -4( U ) T46V 32LG 1
M O I/F EM RY 39V ( X 1) F020 U
O AD CM D R[0.19],O M A [0.7] C D TA
TX 0+/-, TX 1+/-, TX 2+/-,TX 3+/-, TX C+/A A A A A TX 0+/-,TX 1+/-, TX 2+/-, TX 3+/-, TX C+/B B B B B

TOPA EL N (CN 2)

LBA C_RETU / IN / IN / IN D RN 3

K CO TRO EY N L (CN 4)

M TE U

PW 1 M

V LU E O M

A D IN( L/R) U IO

AD U IO TPA 3002D ( U ) 2 9

SPK R0+/SPK L0+/-

SPEA K ( CN ) 6

- 14 -

PCB CONDUCTOR VIEW

Main Board

- 15 -

Button Board

- 16 -

Chapter 2

OPERATING INSTRUCTIONS Front Panel Definition
This Section defines the front panel User Interface for Led Indictor and Key function. Key Definition: There are five keys defined in this system and described bellows. * Adjusting display settings

External Controls

Power on/off 1 POWER Blue: power on Orange: in sleep mode 2 OSD Function Press to view OSD. Press again to enter a selection in OSD.
If OSD is active, press to select or adjust OSD options. If OSD UP/ PLUS is inactive, press once, then press the buttons marked or to adjust the volume. DOWN / MINUS If OSD is active, press to select or adjust OSD options. If OSD is inactive, press once, then press the buttons marked or to adjust the volume. If OSD is active, press to exit a selection in OSD. If OSD is inactive, press and the monitor will automatically optimize the position, focus and clock of your display.

- 17 -

OSD Menu Picture
Brightness: This adjusts the brightness of the picture on the screen. Contrast: This adjusts dark and light shades of color relative to each other to achieve a comfortable contrast. Color temp. : There are three ways of adjusting color: Warm (Reddish white) Cool (Bluish white) User : You can adjust the colors red, green and blue to the intensity you desire. Focus: This removes any horizontal distortion and makes the picture clear and sharp. Clock: If there are any vertical stripes seen on the background of the screen this renders them less noticeable by minimizing their size. It also changes the size of the horizontal screen. H-Position: This adjusts the horizontal screen position. V-Position: This adjusts the vertical screen position.

Volume: Adjusts the volume. Mute : on /off

- 18 -

Option
Auto Config. : System runs auto-configuration. Reset: Recall to default settings. Information: This shows brief information on the screen.

Setting

Language: Select the OSD menu language from English, French, German, Italian, Spanish, Simplified Chinese, Traditional Chinese, Japanese and Russian. OSD H. Position OSD V. Position OSD Time-out This changes the position of the OSD window on the screen and staying time.

LED Definition

The system equips one dual color (blue/amber) led to indict system status and defined as bellows : LED Color Blue Amber Dark System Status System in normal operation mode System in power-saving mode System in power-off mode

- 19 -

LOGO :
When the monitor is power on, the LOGO will be showed in the center, and disappear slowly.
HOW TO OPTIMIZE THE DOS-MODE Plug and play
Plug & play DDC2B feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC2B. The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel. THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL. This monitor meets the Green monitor standards as set by the Video Electronics Standards Association(VESA) and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees (NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is no video-input signal present. When there is no video input signal this monitor, following a time-out period, will automatically switch to an OFF mode. This reduces the monitors internal power supply consumption. After the video input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to a Screen Saver feature except the display is completely off. The display is restored by pressing a key on the keyboard, or clicking the mouse.

- 20 -

USING THE RIGHT POWER CORD

- 25 -

1. Get inverter and insert cable
2. Insert button cable in main board connector
1. Lock 4*pcs screw to fasten m/b and PCB BKT
First to lock 4*pcs screw to fasten Inverter board on the PCB BKT
2. Get m/b and insert speaker cable, then assemble it on the
1. Lock 4 pcs screw to fasten m/b on the pcb BKT
1. Insert INV-M/B cable, then tidy button cable and inv-m/b

- 26 -

Lock screw*2pcs to fasten panel hold
insert LCD cable in m/b connector
1. Assemble shielding and pcb BKT 2. Lock 7pcs screw to fasten shielding 3. Insert ccft cable L/R of into inverter/b connector
1. Stick al foil *2pcs on ccft connector of pcb shielding
1. Lock io nut 2pcs in VGA connector
1. Assemble button/b and back cover

- 27 -

1. Insert button/b cable in button/b connector
1. Assembly back cover and bezel 2. Lock screw * 6 pcs cover to fasten and back
1. Lock screw*2 pcs to fasten bezel and PCB shielding.
2. Assembly DVI box, if necessary.
1. Assembly stand base and back cover. 2. lock screw *6 pcs to fix it.
1. Assembly VESA cover and back cover.

- 28 -

Chapter 4
TROUBLE SHOOTING This chapter provides trouble shooting information forAL2032

1. No Power No Power

Check Adaptor Power Output =18V
Change Adaptor Power Board
Check Scalar Module Output L4 =5V? U4 #2 = 3.3V ? L 13 = 1.8V ? NO Change Scalar Module Board
Check Power Button From Scalar/B(CN5) to Button/B(CN1)

Check Cable Yes Open ?

Change Cable
Change Switch or Button Board

- 29 -

2. No Characters , Missing one color
NoCharacters Missing one color

Check CN4 12Vdc Output

Change Adaptor

Check L4 5Vdc Output

Check or Change U2 , Q6 , D3
Check U6(pin2) 1.8Vdc Output

Check or Change U6

Check U4(pin2) 3.3Vdc Output

Check or Change U4

Change Inverter Board
Check Inverter From Scaler board OK ?
Check CN2 to Panel Signal Output
Check or Change Cable Or Panel

Check X Tal 14.318 Mhz ?

Change X1
Change VGA Cable Check H , V SYNC ?

Change U5

- 30 -

3. No audio

No Audio
Check Input source Or Change CN9 Check Input Signal CN9 OK ?
Check CN6 to Speaker OK ? Change Speaker or CN6(Cable)
Check U12(Pin9) Change U12 or U9 & U9 OK ?
Check U9Pin1(Mute) & Q10 & U9 OK ?

Change Q9 or U9

- 31 -

Chapter 5

Connector Information
Phonejack stereo PIN1. AC power cord : CEE22 typed connector PIN2. Audio cable PIN3. Audio : Line-in receptacle

PHONEJACK STEREO

Video signal connector 15P Mini D-Sub connector x 1

CN6 DB15HD

PIN 15
MNEMO RV GV BV NC GND RG GG BG +5V SG NC SDA HS VS SCL
SIGNAL Red Video Green Video Blue Video None Ground(DDC return) Red GND Green GND Blue GND + 5V (for DDC) Sync GND None DDC Data Horizontal Sync Vertical Sync DDC Clock

- 32 -

Proprietary connecting of DVI box The 44 pin of proprietary DVI box is defined as follows: RX2RX2+ RX1RX1+ RX0RX0+ RXCRXC+ GND GND Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 LLC VPC KEY1 GND KEY44 SCART_FUNC KEY3 SCART RGB_CON SCL5V nYCOEN SDA5V NVDSW_SEL HSCL REST HSDA DVI_ DETECT CORD_ RESET CORD_DETECT ADO_L DETECT AGND IR0 ADO_R V51R GND V12 V12

- 33 -

Chapter 6
FRU (Field Replaceable Unit) list
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of AL2032W. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). NOTE : Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel(http://aicsl.acer.com.tw/spl/). For whatever reasons a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED CERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts repair and service of customer machines. NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how best to dispose it, or follow the rules set by your regional Acer office on how to return it.

- 34 -

AL2032W Exploded Diagram

Chapter 7

SCHEMATIC DIAGRAM

Main Board Circuit

+1.8V_CORE

V / F u C

6 / F u 4. C

6 / F u 41. C

6 / F u 5. C

6 / F u 11 4. 10 C

6 / F u 3. C

6 / F u 51 3. 10 C

6 / F u 0 1. 1 C

6 / F u 91 3. 10 C

6 / F 6 u / 61 F 3. u 1 2. C C

6 / F u 51. C

6 / F u 61 4. 10 C

+3.3V_LBADC

+2.5V_DDR

+3.3V_I/O_MALIBU

+3.3V_LVDSB +3.3V_LVDSA +3.3V_LVDS FSVREF

FSDATA[0.31] 5

V / 6F u C2

V / 5F u 52 C2

6 / F u 71. C

6 / F u 7. C

6 / F u 31. C

6 / F u 1. C

6 / F u 1. 1 C

R170 0/6/NC R171 0/6/NC

RX0+ RX0RX1+ RX1RX2+ RX2RXC+ RXC-

GND +1.8V_DVI

6 / F u 91 5. 10 C

6 / F u 21 5. 10 C

V / 4F 5u C2 2

6 / F u 51 5. 10 C

6 / F u 6. C

249R/6 1%

N4 N3 A8 B8 A9 B9 A10 B10 A6 B6 D5 C5 B11
B1 B2 C1 C2 D1 D2 C3 A1 N2 N1 L4 L3 R4

TXD RXD

R131 0/6

R132 0/6

3 BLUE3 BLUE+
3 GREENGREEN+ REDRED+ SOG
+3.3V_PLL 22pF/6 C67 C68 22pF/6

3 VGA_SCL 3 VGA_SDA

14.318MHz

XTAL TCLK

Route (VIN1/ADC_IN1, ADC1_RETURN) and (VIN2/ADC_IN2, ADC2_RETURN) as differential tracks close to each other and ground the return track of each pair very close to the Malibu D12 ball and ground pin Optional Filter Caps in between a pair on LBADC differential tracks close to the Malibu chip

ACS_RSET_HD

G4 G3 XTAL F1 TCLK K3 NO_CONNECT K2 NO_CONNECT ACS_RSET_HD
FSDATA0 FSDATA1 FSDATA2 FSDATA3 FSDATA4 FSDATA5 FSDATA6 FSDATA7 FSDATA8 FSDATA9 FSDATA10 FSDATA11 FSDATA12 FSDATA13 FSDATA14 FSDATA15 FSDATA16 FSDATA17 FSDATA18 FSDATA19 FSDATA20 FSDATA21 FSDATA22 FSDATA23 FSDATA24 FSDATA25 FSDATA26 FSDATA27 FSDATA28 FSDATA29 FSDATA30 FSDATA31

RNRN3 RN3 4

RNRNRN3 4

RN3 RN3 4

FSDATA0 FSDATA1 FSDATA2 FSDATA3 FSDATA4 FSDATA5 FSDATA6 FSDATA7 FSDATA10 FSDATA11 FSDATA9 FSDATA8 FSDATA14 FSDATA15 FSDATA12 FSDATA13 FSDATA16 FSDATA17 FSDATA18 FSDATA19 FSDATA20 FSDATA21 FSDATA22 FSDATA23 FSDATA28 FSDATA26 FSDATA25 FSDATA24 FSDATA29 FSDATA30 FSDATA31 FSDATA27
21 SCART_FUNC 23 SCART_RGB_CON 25 nYCOEN 27 nVDSW_SEL 29 nRESET 31 DVI DETECT 33 CARD DETECT 35 TVBOX_DETECT 39 IR41 43

Y0 Y2 Y4 Y6 LLC_VPC

RX2RX1RX0RXC-
RX2+ RX1+ RX0+ RXC+ Y1 Y3 Y5 Y7 KEY1 KEY2 KEY3 MSTR_SCL MSTR_SDA TT_I2CSCL TT_I2CSDA CARD_RESET ADO_L 8

ADO_R 8

1841 44P

FSBKSEL1 5

FSBKSEL0 5
C19 B19 A19 D18 C18 B18 A18 C17

R78 10K/6

VRED0 VRED1 VRED2 VRED3 VRED4 VRED5 VRED6 VRED7 VGRN0 VGRN1 VGRN2 VGRN3 VGRN4 VGRN5 VGRN6 VGRN7 VBLU0 VBLU1 VBLU2 VBLU3 VBLU4 VBLU5 VBLU6 VBLU7
A23 C22 B22 A22 D21 C21 B21 A21
FSADDR0 FSADDR1 FSADDR2 FSADDR3 FSADDR4 FSADDR5 FSADDR6 FSADDR7 FSADDR8 FSADDR9 FSADDR10 FSADDR11 FSCLKp FSCLKn FSDQS FSDQM0 FSDQM1 FSDQM2 FSDQM3 FSWE FSCAS FSRAS FSCKE FSBKSEL0 FSBKSEL1
AD25 AD26 AC24 AC25 AB26 AA24 AA25 AA26 Y24 AB25 AC26 AB24

U24 U23

FSADDRU0 FSADDRU1 FSADDRU2 FSADDRU3 FSADDRU4 FSADDRU5 FSADDRU6 FSADDRU7 FSADDRU8 FSADDRU9 FSADDRU10 FSADDRU11 FSCLKU+ FSCLKUFSDQSU FSDQMU0 FSDQMU1 FSDQMU2 FSDQMU3 /FSWEU /FSCASU /FSRASU FSCKEU FSBKSELU0 FSBKSELU1
FSADDRU6 FSADDRU5 FSADDRU4 FSADDRU9 FSBKSELU1 FSBKSELU0 FSADDRU8 FSADDRU7

RNRN3 4

R36 R4

33R/6 33R/5

FSADDR6 FSADDR5 FSADDR4 FSADDR9 FSBKSEL1 FSBKSEL0 FSADDR8 FSADDR7 FSADDR0 FSADDR1 FSADDR11 FSADDR10 FSADDR3 FSADDR2

FSADDR[0.11] 5

FSADDRU0 FSADDRU1 RN8 FSADDRU11 FSADDRUFSADDRU3 FSADDRU2 FSCLK+ FSCLK-

FSCLK+ 5 FSCLK- 5

FSDQS 5
B25 A25 D24 C24 B24 A24 C23 B23

R37 10K/6

T25 U25 U26 T24 V26 V25 V24 W26 Y25 Y26

FSDQM[0.3] 5

/FSWEU /FSRASU /FSCASU FSCKEU FSDQMU0 FSDQMU3 FSDQMU1 FSDQMU2
/FSWE /FSRAS /FSCAS FSCKE FSDQM0 FSDQM3 FSDQM1 FSDQM2

/FSWE /FSRAS /FSCAS 5

Place Series term ination resistors on all address and control lines (RN601,RN603,RN605) very close to U600
Unloaded trace im pedance on this interface is 90 Ohm Loaded trace im pedace w ith DRAM load is 65 Ohm (for 2.5 inch total trace length)

FSCKE 5

7 PWMPWM1

PWM0 PWM1

SCART_FUNC SCART_RGB_CON Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7

4606-04-04P-R/NS

LLC_VPC
A20 B20 VCLK C20 VODD D19 VVS D20 VHS_CSYNC B17 VDV VCLAMP C26 C25 PWM0 D26 PWM1 D25 PWM2 OCM_TIMER1 A12 B12 LBADC_IN3 C12 LBADC_IN2 D12 LBADC_IN1 LBADC_RETURN C16 B16 SVDATA0 A16 SVDATA1 D15 SVDATA2 C15 SVDATA3 B15 SVDATA4 A15 SVDATA5 D14 SVDATA6 SVDATA7 A17 A14 SVDV B14 SVODD C14 SVVSYNC D16 SVHSYNC SVCLK

M1 M2 OCM_UDO OCM_UDI

GPIO_G06_B0 GPIO_G06_B1 GPIO_G06_B2 GPIO_G06_B3 A3+ A3AC+ ACGPIO_G05_B0 GPIO_G05_B3 A2+ A2A1+ A1A0+ A0GPIO_G04_B0 GPIO_G04_B1 GPIO_G04_B2 GPIO_G04_B3 GPIO_G04_B4 GPIO_G04_B5 GPIO_G04_B6 GPIO_G04_B7 GPIO_G07_B0 GPIO_G07_B1 GPIO_G07_B2 GPIO_G07_B3 GPIO_G07_B4 GPIO_G07_B5 GPIO_G07_B6 GPIO_G07_B7 LVDS_SHIELD[0] LVDS_SHIELD[1] LVDS_SHIELD[2] LVDS_SHIELD[3] B3+ B3BC+ BC-

R90 R91

20R/6 1% 20R6 1%

DAN202U

% / R 5 7

C91 C92 C69 C94 C93
0.47uF/6 0.01uF/6 0.01uF/6 0.01uF/6 0.01uF/6

% / R 1 R

DB15 HD

A-HS A-VS

C88 0.1uF/6

R86 10K/6

R98 10K/6

% / R R

RGB SIGNAL GNDs at 2-mm from respective RGB series Capacitors

GNDGNDGND

A0 A1 A2 GND

VCC WP SCL SDA

Near VGA pins

R97 22R/6

R95 0/6

GND GND GND

AHS 4 AVS 4

ANALOG DDC

5.6V/NC 5.6V/NC

C N / V 6. D

GND GND

S N / / 0 R R 1 5

C N / V 6 5. D 5

6 / F p 1 C

1A 1Y 2A 2Y 3A 3Y 4Y 4A

6A 6B 5A 5B

VCC GND

6 / F u 7 1. 1 C GNDGND

SN74LVC14A/NC

03. Graphic Inputs

Size Date: Document Number 03. Graphic Inputs Friday , September 10, 2004

Sheet 3

- 38 -

R40 R43 R67

4 /OCM_WE 4 /OCM_RE 4 /ROM_CS

10K/6/NC 10K/6 10K/6

Socke t for a X8 Flash (64/128/256/512K) and PROM JETm em ory Em ulator
OCMADDR18 OCMADDR17 OCMADDR16 OCMADDR15 OCMADDR14 OCMADDR13 OCMADDR12 OCMADDR11 OCMADDR10 OCMADDR9 OCMADDR8 OCMADDR7 OCMADDR6 OCMADDR5 OCMADDR4 OCMADDR3 OCMADDR2 OCMADDR1 OCMADDR0

/OCM_WE /OCM_RE /OCM_CS

V / 0 F 6 u C 2 2

6 / F u 9 1. C

4 OCMADDR[0.19]
OCMADDR[0.19] OCMDATA[0.7]
A18 A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0

A28F001 29LV040B

DQ7 DQ6 DQ5 DQ4 DQ3 DQ2 DQ1 DQ0 CE# OE# WE# VCC VSS
OCMDATA7 OCMDATA6 OCMDATA5 OCMDATA4 OCMDATA3 OCMDATA2 OCMDATA1 OCMDATA0 /ROM_CS /OCM_RE /OCM_WE

4 OCMDATA[0.7]

R68 R69 R70 R62 R55 R47 R50 10K/6 10K/6 10K/6/NC 10K/6/NC 10K/6/NC 10K/6 10K/6/NC
OCMADDR8 OCMADDR9 OCMADDR13 OCMADDR14 OCMADDR15 OCMADDR16 OCMADDR18 OCMADDR17 OCMADDR19 OCMADDR10 OCMADDR11 OCMADDR12
INT_OSC 8-BIT_FLASH2 R65 10K/6 R80 10K/6 R41 10K/6 R46 10K/6 R71 10K/6
Firmware_By pass DDC2BI Serial_Interf ace_Debug1 Serial_Interf ace_Debug2 Serial_Interf ace_Debug3 8-BIT_FLASH1 8-BIT_FLASH3 TCLK OUTPUTS_ZERO OUTPUTS_ZERO

R56 R51 R61 R64 R73

10K/6 10K/6/NC 10K/6 10K/6 10K/6
10: LOW (Use TCLK) 11: LOW (s et all dis play output to '0') 12: LOW 13: LOW(disable s erial inte rface de bug) 14: LOW 15: LOW 16: HIGH (use crystal) 17: LOW (8bit bus w ith OCM acces s e xte rnal ROM ) 18: HIGH 19: LOW

06. Memory I/F

Size Date: Document Number 06. Memory I/F Thursday , September 02, 2004

Sheet 6

1SS355

L2 CX000800000/1206

BOOST IS VCC FB DC DE CF GND

6 / F p C 1 GND

330K/6

6 / F p

6 / F u 8 1. C 0

+ C V / u 1

V / u 1

6 / F u 1 1. C

D2 1SS355

O S / A 6 S QD N

C22 0.1uF/6

C189 1u/8

R149 4K7/6

AIC1563

8 / u 1

3K/6 1%

% / K R 2

2N3906

L31 CX000800000/1206

R25 1K/6 1%

2200pF/6

6 / K 1

4 TUNER12V_KEY

L4 CX000800000/1206

Q20 MMBT3904L

SI9435

C190 0.1uF/6

V / 1 u C 3

C192 0.1uF/6

D3 RB081L-20

20268-04

L37 CX000800000/1206

6 / 4 F 3 p C 0 1

V V / u 0 / C u GND C

4500-07

L35 CX000800000/1206

8 BOOST IS VCC FB DC DE CF GND

ADJ ON/OFF

D21 1SS355

V / u 6 / 1 F u 8. C

% / 5 K 2 R

O S / A 3 S 2 Q D N

C188 0.1uF/6

Q22 MMST3906

8K2/6 1%

R141 953R/6 1%

ADJ/GND

L13 CX000800000/1206

L32 CX000800000/1206

R11 10K/6/NC

+ V / 1 u C 0 1

AIC1084/TO252

R74 148R/6 1%

330R/6 1% +

D22 RB081L-20
V 6 / / 7 u F u 3 / 1. C F 8 p C 0 C GND GND GND

100K/6

VOLUME 8

4 PWM1

4K7/6/NC
6 / F u 1. QMMBT3904L/NC C

R127 1K/6/NC

L33 CX000800000/1206/NC

R57 200/6 1%

L28 CX000800000/1206/NC L29

+ V / 8 u 0 C 1

C23 1u/8

R58 330/6 1%

R17 4K7/6

L1 CX000800000/1206

C25 0.1uF/6

0/6/NS

Q2 MMST3906/NC

ON/OFF

4 PPWR

Q5 MMBT3904L

C9 330uF/16V

C16 0.1uF/6

4 PBIAS

R10 4K7/6/NC

0.8A Max

R8 1K/6

+V / u 1 C

R38 200/6 1% +V / u 1 C

LT1117/TO223

4 PWM0

Q1 MMBT3904L

R39 200/6 1%

Title Size Date:
Document Number 07. Power Tuesday , September 14, 2004

Sheet 7

Acer America Corporation www.acer.com/aac
AL2032W video card information and configuration tips.
Some video cards and on-board video solutions will not support the Wide Screen format (resolution 1680x1050) for the AL2032W. Below is a list of video cards that, according to their manufacturers, will support the Wide Screen format. Note: the list applies to genuine Intel, ATI, or NVidia video cards. OEM versions of the same chipset may not be able to display these modes. If the OEM version of the driver does not work, please try to download the generic driver from the chipset manufacturer.
Legacy AGP (Requires driver update from manufacturer)
ATI RadeonTM X800 XT 256MB DDR-SDRAM ATI Radeon X800 SE 128MB DDR-SDRAM ATI 256MB Radeon 9800XT ATI 128MB Radeon 9800Pro Current video cards ATI Radeon X850 XT Platinum Edition 256MB DDR-SDRAM NVIDIA GeForce 6800 GTO 256MB NVIDIA GeForce 6800 256MB ATI Radeon X300 128MB PCI Express x16 ATI Radeon X300 SE 128MB DDR-SDRAM ATI Radeon X300 SE 64MB DDR-SDRAM Intel GMA 900 Workstation NVIDIA Quadro FX 3400 NVIDIA Quadro FX 1400 NVIDIA Quadro FX 1300 NVIDIA Quadro NVS 280 PCI Express NVIDIA Quadro FX4400 ATI Fire GL V3100

Notebook

NVIDIA Quadro FX Go 1000 NVIDIA Quadro FX Go 700 NVIDIA GeForce FX Go 5200 NVIDIA GeForce FX Go 5650 NVIDIA GeForce FX Go 5650 ATI MobilityTM Radeon 9600 Pro Turbo ATI MobilityTM Radeon 9000 ATI Mobility Radeon 9700 ATI Mobility Radeon 9800 Intel GMA 900
Acer makes no representations about the accuracy or suitability of the information included in this document for any purpose and makes no commitment to update the information. THIS INFORMATION IS PROVIDED "AS IS" AND ACER DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF INTELLECTUAL PROPERTY. Acer reserves the right to make any changes in this site or the products and/or the programs described at any time without notice. Applicable law may not allow the exclusion of implied warranties, so the above exclusion may not apply to you.
ATI Video Card Configuration
DVI or VGA Connections. Note: some OEM versions of the ATI cards, will not support the 1680x1050 resolution in both DVI and VGA modes. If the recommended 1680x1050 resolution setting does not appear, try changing the hide modes state 1. 2. 3. Right click on the desktop, choose Properties to get the Display Properties Window. Click on the Settings tab, then click the Advanced button. Click on the Monitor Tab then un-check the Hide Modes that this monitor cannot display check box.
Nvidia Video Card Configuration
DVI or VGA Connection. Note: some OEM versions of the Nvidia cards, will not support the 1680x1050 resolution in both DVI and VGA modes. If the recommended 1680x1050 resolution setting does not appear, try changing the hide modes state 1. 2. 3. Right click on the desktop, choose Properties to get the Display Properties Window. Click on the Settings tab, then click the Advanced button. Click on the Monitor Tab then un-check the Hide Modes that this monitor cannot display check box.
If the recommended 1680x1050 resolution setting still does not appear, try using the Nvidia display application to create a custom resolution. 1. 2. 3. Right click on the desktop, choose Properties to get the Display Properties Window. Click on the Settings tab, then click the Advanced button. Click on the GeForce or Quadro tab, and click the Add button under Custom resolutions and refresh rates.

Acer America Corporation www.acer.com/aac 4. Agree to the disclaimer displayed:
5. Enter the resolution size:
The display mode of 1680x1050 should now appear.