English

Technical Information

Satellite Speakers:

A patented advanced technology driver featuring a unique heat transfer system: special high excursion suspension and a computer-designed anti-resonant cone

Power ratings:

120V Model - 120V @ 60Hz; 80VA 240V Model - 140V @ 50Hz; 80VA

Dimensions: Inputs:

3 x RCA Phono - Line level 1 x Stereo Mini jack - Line level Sub Woofer - 265mm x 190mm x 350mm Satellites - 68mm x 103mm x 90mm

Weight: Outputs:

3 x Speaker terminals 9 Kg

Finishes: Controls:

1 x Volume / Power pot 1 x Bass switch (3 Position) 1 x Centre input switch (2 Position) Black sub woofer Textured black satellites with silver/grey grilles White sub woofer Textured white satellites with silver/grey grilles

Accessories:

2 x 5 metre Speaker cables 1 x 2 metre Signal input cable 1 x Speaker level to line level adaptor cable 2 x Wall brackets

Warranty

Your Acoustic Energy loudspeakers are guaranteed against original defects in materials, manufacture and workmanship for 1 year from the date of purchase. Please retain all original packaging materials for possible future use. Under this warranty Acoustic Energy agrees to repair any defect or, at the companys discretion, replace the faulty component(s) without charge for parts and labour. This warranty does not imply any acceptance by Acoustic Energy or its agents for consequential loss damage and specifically excludes fair wear and tear, accident misuse or unauthorised modification. This warranty is applicable in the United Kingdom only and does not in any way limit the customers legal rights. Claims and enquiries under the warranty for AE products purchased outside the UK should be addressed to the local importers or distributors. If you have reason to claim under the warranty please contact your dealer in the first instance.

OWNERS MANUAL

Designed by KOI Inc (USA) Exclusively for Acoustic Energy Limited (UK) Manufactured in Malasyia. Acoustic Energy Limited, 16 Bridge Road, Cirencester, Gloucestershire GL7 1NJ. UK Tel: +44 (0)Fax: +44 (0)1285 654430

www.aego5.com

AEGO5/p5 Owners Manual Warning
To reduce the risk of fire or electric shock, do not expose this system to rain or moisture.
Important Safety Instructions
To ensure your safety, please read these instructions before operating this unit.
1. Follow all instructions and observe warnings marked

Caution

To reduce the risk of shock, do not remove the cover of this system. There are no user-serviceable parts inside. Refer servicing to qualified service personnel. The CAUTION marks shown on this page are located on the back of your system. The lightning flash, with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the system enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle as marked on the system is intended to alert the user to the presence of important operating and maintenance instructions in this owners guide.
The Acoustic Energy AEGO5 is a powered 5.1 surround sound speaker system designed to give maximum acoustic performance with minimal visual impact. It will enable you to fill your room with sound rather than speakers and get the best from your AV surround system. This manual will help you to get the best out of your AEGO5 system and explain how to link it up with your existing digital decoder (AEGO5) or straight to your DVD player through the Acoustic Energy Aego decoder (AEGOP5).

contents

Important Safety Instructions Introduction Unpacking Connecting AEGO5 (with External Power Amplifier) Key AEGO5 Controls AEGO5 Speaker Placement AEGO5 Speaker Orientation Connecting AEGOP5 Key AEGOP5 Controls AEGOP5 Front Panel AEGOP5 Rear Panel AEGOP5 Remote Control AEGOP5 Operation LCD & LEDs LCD Display 16 16

on the unit.

2. Always use the correct line voltage. Please refer to page 6,
and find out the correct power requirements in your area. Please note that different operating voltages may require the use of different adapters.
3. Do not install the unit in an unventilated rack, or directly

Section one

- will deal with the AEGO5 speaker system, how to integrate your existing decoder and placement of your Aego satellite speakers.
above heat producing equipment such as power amplifiers.
4. To avoid shock or fire hazard, do not expose the unit to rain
or moisture, or operate it where it will be exposed to water.
5. Do not attempt to operate the unit if it has been dropped,

Section two

- will provide details of the Acoustic Energy Dolby Digital/DTS decoder that is supplied in the AEGOP5 system. Also, how to connect your DVD player along with other ancillary equipment.
damaged, exposed to liquids, or if it exhibits a distinct change in performance indicating the need for service.
6. Only qualified service personnel should open this unit. 8. Removing covers will expose you to hazardous voltages. 9. Do not overload wall outlet, extension cords or integral

Contents listing:

Mode Selection Input Selection
convenience receptacles, as this can result in a risk of fire or electrical shock.
10. Route power supply cords so that they are not likely to be
1 x AEGO5 subwoofer 5 x AEGO5 Satellite Speakers 5 x Wall Brackets 4 x rubber feet for subwoofer 1 x Multi-way signal cable 3M (6 x RCA Phono to 1 x Multi-pin) 1 x Speaker lead 3.5M 2 x Speaker leads 5.5M 2 x Speaker leads 10M 1 x Owners manual 1 x Car Sticker

Test Mode Mute Mode Master Volume Control Balance Setting Delay Calibration Time Delay Adjustment on Centre Channel Speaker Time Delay Adjustment on Rear Surround Speakers Pro Logic Mode Speaker Mode with Bass Manager Saving Presets
walked on or pinched by items placed on or against them, paying particular attention to cords at plugs, mains adapters, and the point at which they exit from the unit.

AEGOp5 - as AEGO5 plus

1 x AEGOP5 Dolby Digital / DTS decoder 1 x power supply 1 x remote control 2 x batteries for remote control 1 x Multi-pin signal cable 3M (G9 multi-pin to G9 multi-pin)
Loading Presets Sound Field Processing Equalization DRC (Dynamic Range Compression) Resetting Technical Information Warranty

Connecting Aego5

Controls

Existing Decoder

POWER OFF AUTO ON

AEGO5 Speaker Placement

As with all loudspeakers, the placement in relationship to room boundaries (walls etc.) will have a major effect on their overall performance. As the Aego Satellites are so small your choice of positions is far greater and you should use this to maximize the performance of these remarkable little speakers. If a speaker is positioned in free air (not close to any walls etc.) then it will sound brighter. If mounted on or close to a large object (such as a table or on a wall) then the mid range will become louder and the speaker will sound warmer and more powerful. In most situations we would recommend that the satellites are mounted on walls at about head height with the brackets provided to give you a warm powerful sound that you will find pleasing and comfortable. However if this is not possible then Aego Speaker Stands are available from your dealer.
(Alternative) (Alternative) Front Left Subwoofer Front Right

Centre

Front Left

Front Right

Rear Left

Rear Right

see page 5 for connection in to AEGOP5 decoder.
When set to AUTO the Aego system will go in to standby mode if no signal is detected for a period of time (10 minutes). It will automatically switch back on when a signal is detected.

SUB LEVEL

Right Speaker

Centre Speaker

Left Speaker
Sub Level This can be altered to obtain preferred level of bass.

Surface Mounting

AUX. SUB.

Stand Mounting

Wall Mounting

SPEAKER OUTPUTS

FRONT RIGHT

FRONT LEFT

CENTRE

REAR RIGHT

REAR LEFT

OFF AUTO ON

MULTIPIN INPUT
Sub output This output is available to supply an auxiliary subwoofer such as the Acoustic Energy Aegis Compact Sub. This may be recommended when used in a large room.

Surround Right (SR)

Subwoofer

Surround Left (SL)

Volume knob This is the main volume control for all channels. When used with a decoder it would normally be set to maximum, This enables the Aego5 system to be used with DVD players that have a built in decoder but no overall volume control. Detachable grille can rotate to suit speaker orientation.

* Not supplied

Connecting AEGOp5
(with 5.1 Theatre System)

Games Consul

Audio Out

Audio Out L R L R Rec

CD Player

Laserdisc

Optical

DVD Player

Digital Audio Out L Coaxial R

Phono Jack

ACOUSTIC ENERGY LIMITED, 16 BRIDGE ROAD, CIRENCESTER, GLOUCESTERSHIRE GL7 1NJ WWW.ACOUSTIC-ENERGY.CO.UK

Centre Left

OPTICAL IN DIGITAL IN POWER 12V DC
Right Front Right Rear Right Sub AUX 2 AUX 1 LINE IN

MULTIPIN

Developed And Manufactured By Videologic Systems.
AEGOP5 Decoder Right Speaker Centre Speaker Left Speaker
Acknowledgments & Trademarks
All contents are subject to change at any time without notice. No responsibility is assumed for its use; or for infringements of patents or other rights of third parties and no patent or license is implied hereby. All trademarks are the property of their respective owners. Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. (c)1992 - 1997 Dolby Laboratories, Inc. All rights reserved. Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942, 5,956,674, 5,974,380, 5,978,762 and other worldwide patents issued and pending. DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems, Inc. Copyright 1996, 2000 Digital Theater Systems, Inc. All Rights Reserved.

FCC Compliance Statement

The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Shielded cables and I/O cords must be used for this equipment to comply with the relevant FCC regulations.

1. After properly connecting AEGOP5 to your audio sources and amplifier, plug in AEGOP5 s AC adapter to an AC outlet. 2. Turn on the power of AEGOP5 by pushing the POWER button on the front panel. Turn on the power of all audio sources, amplifier, or powered subwoofer. 3. Installation is now complete, get ready to experience true Dolby Digital or DTS surround sound. Note: To prevent damage to speakers, when playing music or a movie, ensure the volume is set low initially.
Gradually turn the volume up to an appropriate level after the playback has started.
Volume knob This is the main volume control for all channels. When used with a decoder it would normally be set to maximum, This enables the Aego5 system to be used with DVD players that have a built in decoder but no overall volume control.

AEGOp5 Decoder

AEGOp5 Remote Control

1 POWER Button

On/off key

2 INPUT MODE Button

Front Left Rear Left

AEGOP5

Select from the 5 different source inputs

3 TEST Button

Test signal for the 6 discrete channels

4 MUTE Button

input power
Mute the sound (toggle on and off)

mute test

balance delay prologic

5 PRO LOGIC Button

Select from 4 different surround settings

AEGOp5 Front Panel

1. The POWER Button Turns AEGOP5 on or off. 2. LCD Display Provides you with information regarding the system status and settings. 3. Speaker Channel LEDs Each LED represents the status of an individual channel. When a particular channel is active, the LED lights up. The colour of the LED also indicates the frequency range of that channel:
* Red means this particular channel has been set to output a wider frequency range that contains bass signal between 20Hz to 120Hz. * Green means this particular channel doesnt contain the bass signal between 20Hz to 120Hz.

6 DELAY Button

Select the desired channel to engage the time delay adjustment

field EQ on/off EQ setup

preset 1 preset 2 preset 3

save1 preset 4 load

7 BALANCE Button
Set the volume setting for each of the 6 channels

BassManager Cen

8 EQ SETUP Button
Select up to 5 EQ Band Settings

SL/SR VOL DRC SW D Time

9 EQ ON/OFF Button
Activate the selected EQ Band Setting

10 FIELD Button

Select from 6 different sound fields
11 PRESET Button (P1, P2, P3, P4)
Recall up to 4 different presets

12 SAVE Button

Store your settings into a selected preset

13 LOAD Button

Activate your saved setting stored in selected preset
Right Front Right Rear Right Sub AUX 2 AUX 1 LINE IN OPTICAL IN DIGITAL IN POWER 12V DC
14 SPEAKER ON/OFF Buttons (CEN, SL/SR, SW)

CEN Button activates/deactivates the centre channel speaker. LS/RS Button simultaneously activates/deactivates the left and right rear speakers. SW Button activates/deactivates the subwoofer.

AEGOp5 Rear Panel

1. MULTIPIN Audio Output: This output feeds 6 channels audio signals to the matching input on a control centre or power amplifier via a multipin (DIN) cable. 2. Main Outputs (Front Left, Front Right, Rear Left, Rear Right, Centre and Sub): The Six outputs feed audio signals to the matching inputs on a control centre or power amplifier. 3. AUX1 AUX2 and LINE Inputs: These inputs accept signals from stereo analog signal sources. 4. OPTICAL and DIGITAL inputs: Your AEGOP5 has two types of digital inputs. One S/PDIF (OPTICAL) and one coaxial (DIGITAL) input. Connect the digital outputs of the sound sources to these inputs. 5. 12V DC Power Input: Connect the AEGOP5 power adapter to an AC outlet. Please refer to page 6 to determine the correct voltage in your area.

15 BASS MANAGER Button

Switches between three bass configurations (bass config.1, bass config.2 and bass config.3)
16 VOL + and VOL Increase/decrease the volume.

17 D TIME Button

Increase/decrease the delay time.

18 DRC Button

Select among 3 different dynamic range compression ratios.

19 RESET Button

Resets the system to its factory default settings.

AEGOp5 Operation

The following pages provide information on the operation of AEGOP5. The AEGOP5 was purposely designed to be simple to operate with all functions available from the remote control.
AEGOP5 Operation - Test Mode
Test Mode After connecting up to your source and speakers, you can press the TEST button on the remote to test the system. You can also use the test mode to test the location of the speakers. When the TEST button is pressed, white noise is generated through all satellite speakers in an order of Front Left, Centre, Front Right, Rear Left, and Rear Right channels for 2 seconds each. When completed, the AEGOP5 returns to Auto Decode mode.
AEGOp5 Operation - Input Selection
Input Selection The AEGOP5 can be connected to up to 5 audio sources. Select the input source you want by repeatedly pressing the INPUT Button on the remote control until the desired source is selected.
AEGOp5 Operation - Master Volume Control
Volume Setting To increase or decrease the master volume of your AEGOP5, simply press VOL + or VOL - on the remote control.
AEGOp5 Operation - LCD and LEDs
1. Press the power button to turn the AEGOP5 on, press it again to turn it off. 2. When power is turned off but still connected to the mains: a. LCD display and Speaker Configuration LEDs are off. b. Decoder status and user configurations are stored. c. Once the power is turned on again, AEGOP5 will resume to its previous decoder status and user configurations. 3. When power is turned off and the unit unplugged from the mains: a. LCD display and Speaker Configuration LEDs are off. b. Decoder status and user configurations are not stored. c. AEGOP5 will reset to factory defaults if the adaptor is reconnected to the mains.

preset 4

mute balance delay

test prologic

BassManager
SL/SR field EQ on/off EQ setup DRC preset 1 preset 2 preset 3 reset save1 preset 4 load VOL

SW D Time

EQ on/off EQ setup

preset 1

preset 2

preset 3

Example: Volume being decreased by 3 decibels.

SL/SR VOL DRC

DOLBY DIGITAL CO VOLUME -03DB
In the Digital Mode (Dolby Digital / DTS), you can manually select the audio input source either in coaxial or optical form depending on the input type. If COAXIAL is selected, the display shows the following information:
When test mode is running, the display shows information in a sequence as below:
DOLBY DIGITAL CO TEST L DOLBY DIGITAL CO TEST C DOLBY DIGITAL CO TEST R DOLBY DIGITAL CO TEST SL DOLBY DIGITAL CO TEST SR
AEGOp5 Operation - Balance Setting
Balance Button You can set the volume setting of each individual channel. To select a channel, press BALANCE button on the remote control repeatedly until the desired channel is reached. Adjust volume on selected channel by pressing VOL + or VOL - on the remote control. Example: Press the BALANCE button once to display the current balance volume for channel L (Left).
AEGOp5 Operation - LCD Display
Auto Decode Mode (Auto detection of input type) When AEGOP5 is turned on, it automatically detects and identifies the audio signal coming from source unit. Playing a DVD title with Dolby Digital (AC3) format, the display shows the following information.
DOLBY DIGITAL CO SURROUND
If Optical is selected, display of AEGOP5 shows the following information:
DOLBY DIGITAL OP SURROUND
In the PCM mode, you can switch between 3 audio input sources such as CD Player, VCR, game consoles etc. (See page 8 or page 9 for reference). The display shows the following information:
Playing a DVD title with DTS format, the display shows the following information.
PCM STEREO PCM STEREO PCM STEREO

LINEIN AUX1 AUX2

DTS COAXIAL SURROUND
Playing DVD, CD, LD, VCR and games consoles connected to the analog inputs (LINE, AUX1 and AUX2), the display shows the following information.
AEGOp5 Operation - Mute Mode
Mute Mode Pressing MUTE Button on the remote control will mute all signal outputs (including the multipin and 6 RCA connectors.) To disable the mute function, press MUTE Button again.
DOLBY DIGITAL CO BALANCE L 0DB
Press the BALANCE button again to select the next channel.
input power mute balance delay test prologic

PCM LINEIN STEREO

DOLBY DIGITAL CO BALANCE R 0DB
Press VOL + or VOL - will increase or decrease the balance volume for selected channel.
AEGOp5 Operation - Mode Selection

Surround Processing Modes: The versatile AEGOP5 surround sound processor is capable of processing both the digital or analog audio signals from many different types of audio source. With the equipment connected correctly, AEGOP5 automatically detects the type of digital signal present at the digital input.
DOLBY DIGITAL CO BALANCE R +0DB
When MUTE Button is pressed, the display shows the following information:
DOLBY DIGITAL CO SURROUND MUTE
AEGOp5 Operation - Delay Calibration
Subwoofer Front Left Centre Front Right
AEGOp5 Operation - Pro Logic Mode
Pro Logic Mode Your AEGOP5 will automatically switch to Pro Logic mode when it detects a Pro Logic signal. With other types of input signal, you can select the Dolby Pro Logic mode manually by pressing Pro Logic button on the remote. Repeatedly pressing the Pro Logic Button will switch the Pro Logic mode in between the following modes; AUTO, ALL PCM, ENABLE and DISABLE.
Press the DELAY Button will display the current delay time for channel LS.
Pressing the SL or SR button, switches the surround channels on and off. The LCD will display the following:
DOLBY DIGITAL CO DELAY SL 5 MS
Press the DELAY Button again will circle to next channel.
DOLBY DIGITAL CO SPK SUR ON
mute balance delay test prologic
DOLBY DIGITAL CO DELAY SR 5 MS
Press the D TIME + or D TIME - button will increase or decrease the delay time for current channel.
DOLBY DIGITAL CO SPK SUR OFF
Pressing the SW button, switches the subwoofer on and off. The LCD will display the following:
DOLBY DIGITAL CO DELAY SR 6 MS
DOLBY DIGITAL CO SPK SW ON DOLBY DIGITAL CO SPK SW OFF
Bass Manager Pressing the BASS MANAGER button enables you to select from three different settings of Bass; Bass Config.1, Bass Config.2 and Bass Config.3. These selections will feed the bass signal below 120Hz to different speakers as described below. Bass Config.1 With this setting, the bass signal below 120Hz will be sent to the subwoofer; the LEDs on the front panel indicating SW will be red, and the LCD will show the following:

SL/SR VOL

SW D Ti
The recommended listening position is described below:
Centre channel speaker should be placed the same distance as the left and right speakers from your listening position. Rear left and right speakers should be placed behind your listening position and above ear level. If speaker placement is restricted due to the physical environment of the room, delay calibration is sometimes necessary to achieve the ideal listening environment. If the centre speaker can only be placed nearer to you than the left and right speakers, sound from the centre speaker will arrive before the sound from the left and right speakers. The difference in arrival time could may affect the sound quality and effect. Your AEGOP5 allows you to adjust the speaker time delay to compensate for this problem by increasing the delay time for the centre channel. Thus sound from the centre, left and right speakers will reach you at the same time. If your centre speaker is closer to your listening position than the left and right speakers, press DELAY button repeatedly until the centre channel is selected. To increase or decrease the delay time, press D TIME + or D TIME - until the desired delay is selected. The same procedure can be applied to adjust the delay time of rear surround speakers if necessary.
AEGOp5 Operation - Time Delay Adjustment on Surround Speakers
Delay Calibration Press DELAY Button and repeat to select the length of delay time for SL/SR/C channels. The delay range for SL/SR is 0 to 15 ms and 0 to 5 ms for centre. Adjust the delay time on selected channel by pressing D TIME + or D TIME - on the remote control.
If a Pro Logic signal is detected, AEGOP5 will switch to Pro Logic mode automatically, and the display shows the following information:
DOLBY DIGITAL CO PROLOGIC AUTO
If a stereo signal (either analog or digital) is detected, AEGOP5 will switch to stereo mode automatically. You can then convert the stereo mode to Pro Logic mode by pressing the Prologic button until you see the following on the display:
DOLBY DIGITAL CO PROLOGIC ALL PCM DOLBY DIGITAL CO PROLOGIC ENABLE
If you want to convert Pro Logic or 2-channel Dolby Digital signal into Stereo mode, you can press the Prologic button until you see the following on the display:
DOLBY DIGITAL CO BASS CONFIG.1
Bass Config.2 With this setting, the bass signal below 120Hz will be sent to front left and right speakers and the subwoofer; the LEDs on the front panel indicating L/R/SW will be red, and the LCD will show the following information:

Surround Speaker Delay Delay calibration for the rear surround speakers may be necessary if the surround speakers are placed quite close to your listening position. To correct the delay this may cause, press the DELAY button repeatedly until SL or SR appear on the display. Increase the time delay of the surround speakers by pressing D TIME + until you are able to hear a 3D sound effect coming from surround speakers. Press DELAY Button again to move to the next channel.
DOLBY DIGITAL CO PROLOGIC DISABLE
DOLBY DIGITAL CO BASS CONFIG.2
Bass Config.3 With this setting, the bass signal below 120Hz will be sent to all the speakers; the LEDs on the front panel indicating L/R/SL/SR/SW channels will be red and the LCD will show the following information:
AEGOp5 Operation - Speaker Mode with Bass Manager
Speaker Mode with Bass Manager The six LEDs on front panel of your AEGOP5 represent the six discrete audio channels (Left, Right, Centre, Rear Left, Rear Right and Sub). If a particular channel is active, the LED will light up in green. The LED will be red if that particular channel carries bass signal below 120Hz. Speaker Mode Pressing the CEN button, switches the centre channel on and off. The LCD will display the following:
field EQ on/off EQ setup preset 1 preset 2 preset 3
AEGOp5 Operation - Time Delay Adjustment on Centre Channel Speaker
Delay Calibration Press the DELAY button and repeat to select the length of delay time for the Rear Left (SL), Rear Right (SR) and Centre(C) channels. The delay range for SL/SR is 0 to 15 ms and 0 to 5 ms for centre. Adjust the delay time for the selected channel by pressing D TIME + or D TIME - on the remote control.
DOLBY DIGITAL CO DELAY SL 5 MS DOLBY DIGITAL CO DELAY SR 5 MS
Press D TIME + or D TIME - to increase or decrease the delay time for the selected channel.
DOLBY DIGITAL CO BASS CONFIG.3
Bass Config. Off With this setting, the bass signal below 120Hz will be sent to all the speakers; the LEDs on front panel of AEGOP5 indicating L/R/C/SL/SR/SW channels will be red and the LCD will show the following information:.
DOLBY DIGITAL CO BASS CONFIG.OFF
DOLBY DIGITAL CO SPK C ON DOLBY DIGITAL CO SPK C OFF
AEGOp5 Operation - Saving Presets
Setting Presets The AEGOP5 enables you to customise up to 4 settings. This function enables you to save and load your favourite settings at any time. Saving a Preset: Press the PRESET 1 button, the display will show the following:
Press the EQ SETUP button to display the current setting of EQ Band 1.
AEGOp5 Operation - Sound Field Processing
DSP Sound Field Your AEGOP5 is equipped with a sound field processor that gives you six different field effects; Disable, Hall, Theater, Stadium, Club, and Church. By pressing Field button on the remote, you can select any of these effects. You can also increase or decrease the Reverb value from 0 - 9 by pressing VOL + or VOL - on the remote control whilst you are selecting the field effect. Press the Field button and repeat to change the current setting of Sound Field mode.

DOLBY DIGITAL CO EQ BAND 1 0DB
Press the EQ SETUP button again to select next EQ Band.
AEGOp5 Operation - Resetting
Resetting Your AEGOP5 can be reset to its factory default settings by pressing RESET button on the remote.
save1 preset 4 load BassManager Cen

prologic

DOLBY DIGITAL CO EQ BAND 2 0DB
Press the Vol+ or Vol- button to increase or decrease the volume for current EQ Band.
DOLBY DIGITAL CO PRESET 1
Press the SAVE button to save all the current decoder settings into Preset 1.
DOLBY DIGITAL CO EQ BAND 2 +01DB
Press EQ SETUP button to store the new EQ setting. Press EQ ON/OFF button to switch the new EQ settings on or off.
Press the RESET button to reset the AEGOP5 to its factory default settings.
DOLBY DIGITAL CO RESET TO FACTORY
When completed, your AEGOP5 reverts to Auto Decode mode.
DOLBY DIGITAL CO PRESET 1 SAVING DOLBY DIGITAL CO PRESET 1 SAVED
When complete, your AEGOP5 will revert back to Auto Decode mode.
DOLBY DIGITAL CO DIABLE REVERB 0 DOLBY DIGITAL CO HALL REVERB 3 DOLBY DIGITAL CO THEATRE REVERB 3 DOLBY DIGITAL CO STADIUM REVERB 3
AEGOp5 Operation - DRC (Dynamic Range Compression)
DRC Your AEGOP5 features Dynamic Range Compression (DRC), its sophisticated technology creates realistic sound fields with richly detailed sound that is remarkably free from distortion. Repeatedly pressing DRC button will switch between 3 modes: NO No compression is applied to the original audio signal, this provides the greatest dynamic range. HALF Partial compression is applied, this function is useful if AEGOP5 is connected to an external amplifier.

DOLBY DIGITAL CO

AEGOp5 Operation - Loading Preset
Loading a Preset You can load a previously saved preset by pressing LOAD button on the remote. Loading a Preset: Press any of the 4 preset buttons, (PRESET 1, PRESET 2, PRESET 3 or PRESET 4), the display will show the following:
DOLBY DIGITAL CO CLUB REVERB 3 DOLBY DIGITAL CO CHURCH REVERB 3
AEGOp5 Operation - Equalization
5-Band Equalization Your AEGOP5 features a 5-band equalizer which enables you to fine tune the sound of your favourite movie or music. Press EQ SETUP button on the remote to activate it. Repeatedly pressing EQ SETUP button will switch between the 5 bands. Each band of the equalizer enables you to adjust your desired volume to a maximum of 10dB. Press VOL + or VOL - on the remote control to adjust the volume. After setting the desired volume for each EQ band, you press EQ SETUP button again to store the new setting for that band. Press EQ ON/OFF button to switch the new EQ settings on or off.

FULL Full compression is applied, this function is useful if AEGOP5 is connected to an external amplifier.
Press LOAD button to load the preset.
Press the DRC button to display the current setting of Dynamic Range Compression mode.
DOLBY DIGITAL CO PRESET 1 LOADING DOLBY DIGITAL CO PRESET 1 LOADED
When preset loading is complete, your AEGOP5 will revert back to Auto Decode mode.
DOLBY DIGITAL CO DYNAMIC NO
Press the DRC button again to switch between the DRC modes.
DOLBY DIGITAL CO DYNAMIC FULL DOLBY DIGITAL CO DYNAMIC HALF