Bioscrypt V-Pass FX

Flexible Security Options

FEATURES

Industrys most accurate finger-scan algorithm (#1 at FVC 2002 & FVC 2004) RoHS compliant User configurable 1:N mode or 1:1 mode New blue LED power signal Self-contained reader stores approximately 4,000 finger-scan templates in 1:1 mode, 500 finger-scan templates in 1:500 mode, and 200 finger-scan templates in 1:200 mode USB communication via Aux port VeriAdmin software (included free of charge) offers a simple approach to initial setup, template management, and networking configuration User-friendly installation with pigtail connections and flat surface, single-gang, or mullion mounting Simple one-touch enrollment Intuitive user interface provides feedback via multi-colored LED and tone signals Flexible communication options support Wiegand formats up to 64 bits Duress finger option.
Finger-only security in 1:N mode or dual-factor authentication in 1:1 mode with an external Wiegand reader Ideal for retrofitting existing legacy systems to dual biometric/ authentication solutions in 1:1 mode

TECHNICAL INFORMATION

DIMENSIONS Length: 130 mm (5.12 in) Width: 50 mm (1.97 in) Depth: 63.5 mm (2.5 in) COMMUNICATIONS: Pigtail wire connections for RS-232 and RS-485 Wiegand IN/OUT USB Aux port

ORDERING INFORMATION

By default, the Bioscrypt V-Pass FX is set to 1:500 mode. The reader must be configured manually to run in 1:200 or 1:1 modes. V-PASS-FX-A,R: Finger-scan reader (using customer-supplied external Wiegand device) DESKTOP-VS-FX-A,R: V-PASS-FX-A,R reader mounted on a plastic stand, with power supply DEMO-VS-FX-A,R:
VERIFICATION (1:1): Enrollment time: < 3 seconds Verification time: < 1 second False Acceptance Rate (FAR): Adjustable False Rejection Rate (FRR): Adjustable Equal Error Rate (EER) (FAR=FRR): 0.1% Number of templates: ~ 4000 per unit Template size: ~ 350 bytes IDENTIFICATION (1:N): Enrollment time: < 3 seconds Verification time: < 2 seconds FAR: 0.2% FRR: 1.0% Number of templates: 500 per reader in 1:500 mode; 200 per reader in 1:200 mode Template size: ~ 2500 bytes VOLTAGE: 9-24 VDC CURRENT DRAW: Idle: 0.20 amps @ 12 VDC Max: 0.40 amps @ 12 VDC MOUNTING: Flat surface, single-gang, or mullion mountable Wall mount plate accepts #6 screws or bolts Clearance hole diameter is 3.94 mm (0.155 in) Trim plate included to cover single-gang box. OPERATING TEMPERATURE: 0 - 60C CERTIFICATIONS: FCC, CE, UL294, cUL, RoHS
V-PASS-FX-A,R reader mounted on stand, with power supply and case BIO-SDK: Development software CD (supports all Bioscrypt products) OUTDOOR ENCLOSURE: The Bioscrypt V-Pass FX is compatible with the Bioscrypt V-Cerco or V-Cerco-HT protective enclosures. Contact Bioscrypt for more information.
BIOSCRYPT INC. 505 Cochrane Drive Markham, ON, Canada L3R 8E3
P: 905.940.7490 F: 905.940.7492 sales@bioscrypt.com

Bill Redirect Send Bioscrypt Fingerprint V-Pass reader numbers directly in your existing application software
Documentation: 16/08/2009
Use this documentation with the product : Bill Redirect 5.0J and more
Software configuration and integration service
It's free, fast, and efficient ! Submit your case to info@billproduction.com and receive a customized answer !
Our Internet site: http://www.billproduction.com/ Email: info@BillProduction.com
This documentation demonstrate how Send Bioscrypt Fingerprint V-Pass reader numbers directly in your existing application software
The following instructions apply to:
Bioscrypt Fingerprint V-Pass reader http://www.l1id.com/pages/399-bioscrypt-v-pass-fx
Step #1 Install and Start the software VeriAdmin
This software is include with your Bioscrypt V-Pass reader
To Configure the Unit Parameters
Select the option: Communication Enter in the field Assign Uni Network ID: 0 Select the option: 0 Host 232/Aux 232 (RJ11) Set the 2 Baud options to: 57600 Click on button: Apply
Select the option: Verifiction Response Check the 2 options: Always (with ID) Click on button: Apply Close this software: VeriAdmin
Step #2 Download and install Bill Redirect software http://www.billproduction.com/Bill_COMtoKB.ZIP

Step #3

Disable all except the Serial Port and Keyboard Buffer section. Set to OFF Serial Port and Pressed key switch.

Step #4

Click on button: Configuration. Enter the Serial Port Number where your Bioscrypt V-Pass reader is connected The Serial Port Configuration is: Bauds: 57600 Parity: None Databits: 8 StopBits: 1 Timeout:.3

Step #5

Click on button: Configuration

Click on button: Add

Enter in this field: {START_WITH}{ASCII:64}
Enter in this field: {CNV_BIOSCRYPT[RX_DATA]}{ASCII:13}

Step #6

Enable the section: Virtual Keyboard Click on button: Configuration

Step #7

Enter in the field Button Text: Mode Enrollment Enter in the field String to send is push: {SERIALPORTNUMBER[0]} Enter in the field Window Title: VeriAdmin Move this button on: The top right in your Windows

Step #8

Enter in the field Button Text: Mode Reader Enter in the field String to send is push: {SERIALPORTNUMBER[1]} Enter in the field Window Title: VeriAdmin * Replace the number 1 by the Serial Port Number where your Bioscrypt V-Pass reader is connected
Move this button on: The top right in your Windows (just across the first button)

Step #9

On main screen Click on button: Save Configuration Click on button: Minimize to Tray Icon Open the Windows NotePad At this step If your configuration is correct you can see the each Finger number appear in the NotePad
To enroll a new finger Open the software: VeriAdmin Click on button: Mode Enrollment Do the enrollment To return in mode Reader Click on button: Mode Reader Close the software: VeriAdmin
To send Bioscrypt number directly in a field of another software and click on a button, use the command TX_FIELD and CLICK_BUTTON commands

Example At Step #5:

{TX_FIELD[AppName,22,{CNV_BIOSCRYPT[RX_DATA]}]}{CLICK_BUTTON[AppName,131]} For more information, consult the product manual: http://www.billproduction.com/Bill_Redirect_Manual.pdf
Optional: Create a log file (Date, Time, UserNumber) readings made by the V-Pass scanner.
Click on button: Add Enter in this field: {ALL_RX} Enter in this field:
{TX_FILE[C:\LOG_VPASS.TXT,{CURDATE:MM-DD-YYYY}{ASCII:9}{CURTIME}{ASCII:9}RX_DATA]}RX_DATA
If you want log file and not receive the number via the keyboard, just uncheck the section Keyboard Buffer.
On main screen Click on button: Save Configuration Click on button: Minimize to Tray Icon At this step If your configuration is correct you can see the each Finger number appear in the file: C:\LOG_VPASS.TXT