General Operation

Your system's sensing devices have been assigned to various "zones." For example, the sensing device on your entry/exit door may have been assigned to zone 01, sensing devices on windows in the master bedroom to zone 02, and so on. These numbers appear on the display when an alarm or trouble condition occurs.
LYNXR is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N LYNXRCHKIT-HC) is installed.
The fire protection portion of your security system (if used) is always active and will sound an alarm if a fire condition is detected. Refer to the FIRE ALARM SYSTEM section for important information concerning fire protection, smoke detectors and planning emergency exit routes from the premises.

Fire Protection

Burglary Protection
Your system provides two modes of burglary protection: STAY and AWAY. STAY mode protects the perimeter only, allowing you to freely move within inside the premises. AWAY mode protects the entire system. Both modes provide an entry delay time that allows you to reenter the premises without setting off an alarm. For additional security, you can turn the entry delay off when arming the system by using the NO DELAY key in combination with the desired arming key. The system also allows you to bypass selected zones before arming the system, if desired. Refer to the BYPASSING PROTECTION ZONES section. The system also provides a CHIME mode, for alerting users to the opening of protected doors and windows while the system is disarmed. You must turn on ("arm") the burglary protection portion of your system before it will sense burglary alarms. To arm the system, enter your security code then press the desired arming key (AWAY or STAY). Refer to the ARMING THE SYSTEM section for detailed procedures and information. At the time of installation, you were assigned a personal 4-digit security or mater user code. You must enter the security code when arming and disarming the system, and when performing other system functions. As an additional security feature, other users who do not need to know your code can be assigned up to 6 different security codes. Refer to the SECURITY CODES section for procedures on adding security codes to the system.

To remotely activate forced bypass: ------To remotely check system status: ---------- [*] To hang up: ------------------------------------*If forced bypass was enabled by your installer. OTHER FUNCTIONS-----------------------To set the time and date: --------------------To set scheduling: ---------------------------To activate or deactivate X-10 devices 1-6: To activate or deactivate X-10 devices 7 & 8: To add a user code: -------------------------To delete a user code (except Master Code): -To turn Test mode on: ----------------------To turn Test mode off: ----------------------FUNCTION

+ [6] + [#]* + [9]

+ FUNCTION + FUNCTION +

LIGHTS ON

+ [63] + [64]
LIGHTS OFF + device number
+ FUNCTION + LIGHTS ON or LIGHTS OFF + dev. no.

** + ** + + +

CODE CODE
+ user no. (02-08)+ user code + user number (02-08)

TEST OFF

To use the defined AUX function: ----------- Press and hold AUX key 2 secs (4 beeps) + To send message to pager: -------------------- Press and hold AUX key 2 seconds (4 beeps) ** Only the master code can be used to add or delete another user code.

About the Master Keypad

General
IMPORTANT: If the keypad beeps rapidly upon entering the premises, an alarm has occurred during your absence and an intruder may still be on the premises. LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location. The keypad allows you to control all system functions. The keypad features telephone-style keys and a Liquid Crystal Display (LCD), which shows the nature and location of all occurrences.

BYPASS

LIGHTS OFF STATUS

FUNCTION

01000-021-V0
The keypad also features a built-in sounder, which will sound during alarms and troubles. The keypad also "beeps" during certain system functions, such as during entry/exit delay times, in Chime mode, and when depressing any of the keys (to acknowledge the key press). In addition, a built-in speaker announces system status.
About the Display and Indicators
Display Definitions (for other displays, see Trouble Messages)
ALARM: Appears when an intrusion has been detected and the system is armed (also appears during a fire alarm or AWAY LOW BAT AC INSTANT CHIME TEST audible emergency alarm). Accompanied by the STAY REC MESSAGE protection zone in alarm. ALARM FIRE BYPASS FAULT All burglary zones, interior and perimeter, are armed. Entry delay is turned off. Perimeter burglary zones, such as protected windows and doors, are armed.

AWAY: INSTANT: STAY:

LOW BAT:
AC: CHIME: TEST: REC: MESSAGE: BYPASS: FAULT:
Appears when a fire alarm or fire fault is present. Accompanied by a display of the zone in alarm. Low battery condition in a wireless sensor (if zone number is displayed) or low system battery (if no zone number is displayed). If 00 is displayed, a wireless keypad (5827) has a low battery condition. Appears when AC power is present. If not lit, the system is operating on backup battery power. Appears when the Chime feature is activated. Appears when the system is in Test mode. Appears when in Recording mode. Appears when a message has been recorded and has not yet been played back. One or more burglary protection zones have been bypassed. Appears when a malfunction is discovered in the system at any time; or if an open is detected in a fire zone at any time; or when a fault in a day/night burglary zone is discovered during a disarmed period. Accompanied by a display of the zone number in trouble. Appears during a remote phone control session.

KEY: Disarms the burglary portion of

18. 19.

10. 11.
KEY: Allows alternate key KEY: Used with STAY or AWAY 20. 21.

functions.

function to eliminate the entry delay. Alarm sounds immediately if entry is opened. 12.

STATUS

KEY: When pressed prior to arming,
the keypad will display all open zones, and will announce system status.
the system, silences alarms and audible trouble indicators, and clears alarm trouble display after the problem has been corrected. MICROPHONE: Used to record personal messages up to 20 seconds long. SPEAKER: Source of audible internal warning and confirmation sounds, status announcments, as well as alarms (see "Summary of Audible Notifications"). RECORD: Activates the recording function to record personal messages. VOLUME: Sets the volume of system announcements and status beeps. KEYS 0-9: Used to enter your individual security access code(s).

6(&85,1*7+(35(0,6(6

Checking System Status
Before arming your system, all protected doors, windows, and other protection zones must be closed or bypassed (see the BYPASSING PROTECTION section). Pressing the STATUS key will announce all zones that are faulted, as well as any other abnormal system condition, making it easier for you to secure any open zones. READY LIGHT: The green READY indicator on the keypad will be lit if the system is ready to be armed. If blinking, the system is not ready.

Press the STATUS Key

Press the STATUS key once to announce the general status of the system. Depending on the current state of the system, the following phrases may be heard: disarmed, ready to arm [message] [check system] disarmed, [not ready to arm], [message] armed [away] [stay] [instant] [check system] [message] NOTE: Phrases in brackets are variable, and are announced only if appropriate in the current state of the system Press the STATUS key twice to announce specific system status. Depending on the current state of the system, the following phrases may be heard: fire alarm [zone voice descriptors] alarm [zone voice descriptors] fire fault [zone voice descriptors] fault [zone voice descriptors] low battery [zone voice descriptor] system low battery check system AC loss zones bypassed chime (second press must be within 5 seconds of first press) VOLUME LEVEL: The volume level of system announcements can be increased or decreased. Refer to the MESSAGE RECORDING/ PLAYBACK section for the procedure.

System Can Be Armed

The READY light will be lit once all protection zones have been closed or bypassed. You may now arm the system as usual. 11

Arming the System

Arming in Stay Mode
Use this mode when you are staying home, but expect someone to use the entrance door later. Close all protected perimeter windows and doors before arming. The green READY indicator on the keypad should be lit if the system is ready to be armed. To arm in STAY mode: + STAY or press and hold STAY ** ** See Quick Arming paragraph.

Your user code**

The keypad beeps three times and displays the armed STAY message. The red ARMED indicator lights and the system announces armed STAYexit now. When armed in STAY mode, the system will sound an alarm if a protected door or window is opened, but you may otherwise move freely throughout the premises. Late arrivals can enter through the entrance door without causing an alarm, but they must disarm the system within the entry delay period or an alarm will occur. Restarting Exit Delay While System Armed Ask your installer if this feature is active for your system. If active, you can restart the exit delay at any time after arming in STAY mode. This is useful if you wish to open the entry/exit door to let someone in after arming the system, and avoids having to disarm the system and then re-arm it again. To restart exit delay while system is armed in STAY mode: Press STAY key

Arming In Away Mode

Use this mode when no one will be staying on the premises. Close all protected perimeter windows and doors before arming. The green READY indicator on the keypad should be lit if the system is ready to be armed. To arm in AWAY mode: + AWAY or press and hold AWAY ** ** See Quick Arming paragraph.
The keypad beeps twice, or beeps continuously if exit warning has been programmed for your system, and displays the armed AWAY message. The red ARMED indicator lights and the system announces armed AWAYexit now. When armed in AWAY mode, the system will sound an alarm if a protected door or window is opened, or if any movement is detected inside the premises. You may leave through the entrance door during the exit delay period without causing an alarm. You may also re-enter through the entrance door, but you must disarm the system within the entry delay period or an alarm will occur.
Arming the System With No Delay
Use NO DELAY with STAY mode when you are staying home and do not expect anyone to use the entrance door. Use NO DELAY with AWAY mode when the premises will be vacant for extended periods of time such as vacations, etc. When armed with NO DELAY, the system will sound an alarm if a protected door or window is opened, including the entrance door. You may leave through the entrance door during the exit delay period without causing an alarm, but an alarm will sound as soon as someone reenters. To arm with NO DELAY: ** See Quick Arming paragraph.

b : xx

xx : bd

Begin Time (minute)

[xx] = begin minute 0 to 59 [*] = continue [#] = return to previous prompt

Begin Day

[xx] = begin day 01 to 17 [*] = continue [#] = return to previous prompt
If the value programmed in the Event Identifier is 3 , 4 ,
or 5 , and the current entry is completed, the system will save all field data up to this field. The system will beep four times and go back to the first field (Schedule Number) with the schedule number advanced. If the value programmed in the Event Identifier is 1 or 2 , and the current entry is completed, the system will advanced to the next programming field - End Time (hour). NOTE: See figure 2 for the definition of begin day entries.

End Time (hour)

The end hour is a two-digit entry. To enter the hour 3, press
0 followed by 3. end time.
The end hour 00 indicates this schedule does not have a Press 0 to select AM or 1 to select PM.

End Time (am/pm)

[0] = end time, am (A) [1] = end time, pm (P) [*] = continue [#] = return to previous prompt

xx : d

End Time (minute)
[xx] = end minute 0 to 59 [*] = continue [#] = return to previous prompt

End Day

[xx] = end day 01 to 17 [*] = continue [#] = return to previous prompt

Device Number

[xx] = device number 1 to 8 [*] = continue [#] = return to previous prompt
NOTE: See figure 2 for the definition of end day entries. If the event identifier is set to 2 upon completion of this field, the current schedule data will be saved and the system will go back to the next schedule number. [*] will accept and save the entire schedule event. The system will beep four times and go back to the beginning of the programming field (Schedule Number) with the schedule number advanced. If the current schedule number is 8, the system will wrap around and set the schedule number to 1. NOTE: For X-10 devices.

Event Identifier Entries

Entry 2 Event Empty X-10 Device Latch Key Report Comment No event scheduled (or schedule is temporarily disabled) Turn an X-10 device, either on or off at begin/end times. (will have a start and end time to program) (time driven) NOTE: SH10A siren cannot be used. Send a special pager report (7110000) indicating system not yet disarmed. (will have a start/end time to send the report) (window driven), (reports only to pager) NOTE: Option *49 must be programmed to be 6 or higher. Make sure unit is armed prior to start of window time. In addition a secondary phone number must be programmed in Option *42. Will arm the system automatically, and bypass any open zones, at a given time. It will send a report to the pager and central station, indicating system has been auto armed stay, plus all bypass reports. (will have only a start time to send the report) (time driven) NOTES: (1) Prior executing auto stay arming, force bypass will be executed - if option *23 was enabled. (2) If pager report is required, Option *49 must be programmed to be 6 or higher. Will beep three times and then announce custom words 72, 73 and 74. This will be repeated every minute until a key is depressed, or a button type zone does an arm or disarm. NOTE: Make sure installer programmed custom words 72-74 at the time of installation. Will start a trouble tone on the speaker, which will continue until a key is depressed.

NOTE: If a remote phone session is not granted by the system, for any of the reasons identified above, a modem tone will be generated before the end of the session. the remote phone access mode.
Using Remote Phone Control Feature
Dial the controlss phone number. If no answering machine is present, the control will pick up between 1 and 14 rings, depending on the number programmed by your installer and will periodically announce SYSTEM. During a remote phone control session PC will be displayed on the control. Enter: (within eight seconds) The system status will be announced. Enter phone control commands as described on the next page: If an answering machine is on the premises, you need to dial the premises and hang up on the first ring. Wait at least five (5) seconds (but no more than 22 seconds) and dial the premises phone number again. The control will pick up and periodically announce SYSTEM. 28

Enter:

Your user code (within eight seconds)
The system status will be announced. Remote Phone Control Commands To remotely disarm system:
To remotely arm in AWAY mode: To remotely arm in STAY mode:

+ [3] + [2] or [3] + [0]

To remotely arm in AWAY or STAY mode with no delay: To remotely activate X-10 devices 1-6: [#] + [4] + device no. To remotely activate X-10 devices 7 & 8:

+ [#] + [4] + device no.

To remotely deactivate X-10 devices 1-6: [#] + [7] + device no. To remotely deactivate X-10 devices 7 & 8:
+ [#] + [7] + device no. + [6] + zone no.
To remotely Bypass zones:
To remotely activate Forced Bypass:

+ [6] + [#]

To remotely check system status: [*] To end remote phone session: Hang Up or

NOTES:

(1) Check with your installer to see if the Forced Bypass mode has been enabled. (2) When bypassing zones, make sure a confirmation beep sounds for each zone that has been bypassed.

),5($/$506<67(0

(If Installed)
Your fire alarm system (if installed) is active 24 hours a day, providing continuous protection. In the event of an emergency, the installed smoke and heat detectors will automatically activate your security system, triggering a loud, intermittent sound from the keypad. An intermittent sound will also be produced by optional exterior sounders, and interlaced with the voice descriptor, sounding every 15 seconds. A FIRE message will appear at your keypad and remain on until you silence and clear the alarm display.

01000-023-V0

OS ET OO DR BE M

M OO DR BE

M OO DR

2nd FLOOR

N HE TC KI

OO DR BE

BACK DOOR

M OO DR BE TH BA

1st FLOOR

6<67(0)81&7,216

For additional security, users other than you who do not need to know your code can be assigned different security codes. These secondary users are identified by "user numbers" when their codes are assigned. You can assign up to 6 user codes (2-digit user numbers 03-08). Note that the master (primary) user of the system is the only one who can assign codes to secondary users, and is designated user no. 02; user no. 01 is the installers code. All codes can be used interchangeably when performing system functions (a system armed with one user's code can be disarmed by another user's code), with the exception of the Babysitter Code described below. Babysitter Code (User 07): This code can be used to arm the system, but cannot disarm the system unless the system was armed with this code. This code is typically assigned to someone (such as a babysitter) who needs to arm/disarm the system only at certain times. The Babysitter Code is assigned to User 07. Duress Code (User 08): This feature is intended for use when you are forced to disarm or arm the system under threat. When used, the system will act normally, but can silently notify the alarm monitoring company of your situation, if that service has been provided. Duress Code is assigned to User 08. The Duress Code is useful only when the system is connected to an alarm monitoring company.
To Add/Delete a User or Change a User's Code
Changing the Master User Code Follow the procedure for changing a user's code, but enter User No. 02 and enter the new code twice. IMPORTANT: Temporary users of the system (e.g., babysitters, cleaning staff) should not be shown how to use any system function they do not need to know, such as bypassing protection zones for example.
Sequential key depressions for all steps in a procedure must be made within 2 seconds of one another, or else the entire entry is aborted and must be repeated from its beginning. Add a user code: Master User Code Delete a user code: Master User Code Wait (about 3 seconds) until the keypad beeps once before pressing any other key. The code is automatically deleted. + CODE Key + user number (03-08) + CODE Key + user number (03-08) + users code
Testing the System (to be conducted weekly)

Entering Test Mode

The TEST key puts your system into the Test mode, which allows each protection point to be checked for proper operation. The keypad sounds a single beep every 45 seconds as a reminder that the system is in the Test mode. NOTE: An alarm message will not be sent to your alarm monitoring company during the following tests. Disarm the system and close all protected windows, doors, etc. The READY message should be displayed and the green READY indicator (if present on the keypad) should also be lit. Enter the security code then press TEST WATCH. All LCD segments will light for 3 seconds. LISTEN. The external sounder should sound for 2 seconds and then turn off. If the sounder does not sound, notify your service company. FAULT ZONES. Open each protected door and window in turn and listen for three beeps from the keypad. Identification of each faulted protection point should appear on the display. The display will clear when the door or window is closed. Walk in front of any interior motion detectors (if used) and listen for three beeps. The identification of the detector should appear on the display when it is activated, and its voice descriptor will be announced (if programmed). The display will clear when no motion is detected. Note that if wireless motion detectors are used, there is a 3-minute delay between activations. This is to conserve battery life. To test all smoke detectors, follow the manufacturer's instructions. The identification of each detector should appear on the display when each is activated. If a problem is experienced with any protection point (no confirming sounds, no display), notify your service company. When all protection points have been checked and are intact (closed), there should be no zone identification numbers displayed on the keypad.

Exit Test Mode

When testing is completed, exit the TEST mode by entering:

User Code + OFF

NOTES: (1) If the Test mode is inadvertently left active, it automatically turns off after 4 hours. (2) Macros cannot be run from the Test Mode.

Trouble Messages

Typical Trouble Condition Displays
To silence the beeping sound for fault conditions, press any key. Indicates that a problem exists with the zone(s) displayed, accompanied by rapid beeping. First, determine if the zone(s) displayed are intact and make them so if they are not. If the zone uses a wireless detector, check that changes in the room (moving furniture, televisions, etc.) are not blocking wireless signals from the detector. If the problem has been corrected, the zone descriptor(s) and FAULT should disappear from the display. If not, key an OFF sequence (security code plus OFF) to clear the display. A fault condition can also indicate a wiring problem. If the FAULT display persists, notify your service company. Note that the system will not allow arming if a fault condition exists. To arm the system with a fault condition present, you must first bypass the zone(s) having the fault condition. Indicates that a failure has occurred in the telephone communication portion of your system FC or a problem with the phone line existed when dialing was attempted. Indicates that the control is on-line with the central station's remote computer. The control CC will not operate while on-line. Wait a few minutes. The display should disappear. If this remains displayed for more than 1 minute, the system is disabled. dI Indicates a cancelled alarm. See Entry/ CA Exit Delay section. Indicates an exit alarm. See Entry/ EA Exit Delay section. Indicates that the system has detected an RF jam condition or excessive interference. If the 90 condition persists, notify your service company. Accompanied by a once-per 45 seconds beeping at the keypad, indicates a low system LOW BAT (no zone no.) battery condition exists. Refer to the procedure on the next page to replace the system battery. Accompanied by a once-per-45 seconds beeping at the keypad, indicates a low battery LOW BAT (with zone no.) condition exists in the wireless transmitter displayed. Accompanied by a once-per-45 seconds beeping at the keypad, indicates a low battery LOW BAT (with zone 00) condition exists in a wireless keypad. Notify your service company. FAULT

Changing the LYNXR/LYNXR24 System Battery
In the event of an AC power loss, the LYNXR/LYNXR24 is powered by a rechargeable, nickel-metal hydride battery pack. The battery pack should be replaced when a LOW BAT message with no zone number is displayed. NOTE: The battery pack (P/N LYNXRCHKIT-SC or LYNXRCHKIT-HC) should be changed every four years and must be replaced by a qualified service technician. Following battery pack replacement, rechargeable batteries may take up to 48 hours to charge. The LOW BAT message may be displayed after one minute, however it should clear within 4 hours or by entering Test Mode.
6XPPDU\2I$XGLEOH1RWLILFDWLRQ
** UPPER CASE indicates announcements after pressing STATUS once, Lower case indicates announcements after

pressing STATUS twice.

INTERRUPTED Speaker and external piezo and bell CONTINUOUS Speaker and external piezo and bell ONE SHORT BEEP (not repeated) Speaker and external piezo

FIRE ALARM

DISPLAY
FIRE ALARM is displayed; zone number in alarm displayed. ALARM is displayed; zone number in alarm displayed. a. Green LED on steady b. The number of the open protection zone is displayed after pressing STATUS. c. Numbers of the bypassed protection zones are displayed (One beep is heard for each zone displayed). a. Opened zone identifications will appear. b. LOW BAT displayed with zone number of transmitter. c. LOW BAT displayed with no zone no. d. FC displayed with no zone no. AWAY or AWAY + INSTANT is displayed. Red ARMED indicator is lit. a. STAY or STAY + INSTANT is displayed. Red ARMED indicator is lit. b. CHIME displayed, number of open protection zone will be displayed if the Status key is pressed. a. FAULT displayed. Number of troubled protection zone is displayed. b. FIRE ALARM or ALARM is displayed; zone number in alarm is displayed. a. Exceeding the delay time without disarming causes alarm. b. AWAY or AWAY + INSTANT is displayed

ANNOUNCEMENT**

fire alarm + zone voice descriptor
(Voice descriptor is interlaced with the siren and sounds every 45 seconds)
BURGLARY/AUDIBLE EMERGENCY ALARM a. SYSTEM DISARM b. SYSTEM ARMING ATTEMPT WITH AN OPEN ZONE. c. BYPASS VERIFY a. SYSTEM IS IN TEST MODE b. LOW BATTERY AT A TRANSMITTER c. SYSTEM LOW BATTERY d. FAIL TO COMMUNICATE ARM AWAY OR MAXIMUM a. ARM STAY OR INSTANT b. ZONE OPENED WHILE SYSTEM IS IN CHIME MODE. a. TROUBLE b. MEMORY OF ALARM a. ENTRY DELAY WARNING b. EXIT DELAY WARNING

alarm + zone voice descriptor
a. DISARMEDREADY TO ARM b. DISARMEDNOT READY TO ARM c. zones bypassed a. No announcement b. low battery + zone voice descriptor c. system low battery d. check system ARMED AWAY [INSTANT] EXIT NOW a. ARMED STAY [INSTANT] EXIT NOW b. zone voice descriptor a. fault + zone voice descriptor b. fire alarm or alarm + zone voice descriptor a. DISARM SYSTEM NOW b. ARMED [AWAY] [INSTANT] EXIT NOW
ONE SHORT BEEP (once every 45 secs) Speaker and external piezo TWO SHORT BEEPS Speaker and ext. piezo THREE SHORT BEEPS Speaker and external piezo RAPID BEEPING Speaker and external piezo SLOW BEEPING Speaker and external piezo
Additional Announcements:
Pressing STATUS key once will announce the following primary messages, depending on the systems status at the time: DisarmedReady to Arm [check system] Disarmed [not ready to arm] Armed [away] [stay] [instant] [check system] [exit now] Pressing the STATUS key twice will announce the following secondary messages, depending on the systems status at the time: Fire Alarm + zone voice descriptor Fault + zone voice descriptor Zones Bypassed Alarm + zone voice descriptor Low Battery + zone voice descriptor System Low Battery Fire Fault + zone voice descriptor Chime AC Loss NOTE: If there are no secondary messages, the primary status messages will be announced. ARMED LED: ON = System armed (Red) OFF = System disarmed Blinking = System armed, but a fault exists. READY LED: ON = System disarmed, ready to arm (Green) Blinking = System disarmed, not ready to arm (a fault exists). NOTE: When the system is armed, the READY LED turns off.
UL NOTICE: This is a " Grade A" residential system.
FCC ID: CFS8DLLYNX RADIO FREQUENCY EMISSIONS Federal Communications Commission (FCC) Part 15
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Industry Canada

This Class B digital apparatus complies with Canadian ICES-003. Cet Appareil num rique de la classe B est conforme la norme NMB-003 du Canada.
TELEPHONE/MODEM INTERFACE Federal Communications Commission (FCC) Part 68
This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains the FCC registration number and Ringer Equivalence Number (REN). You must provide this information to the telephone company when requested. This equipment uses the following USOC jack: RJ31X This equipment may not be used on telephone-company-provided coin service. Connection to party lines is subject to state tariffs. This equipment is hearing-aid compatible.

Silence Alarm..15, 30 Silencing Low Battery Warning Tones.36 Silent Emergency..17 Smoke Detectors..4 Speaker...10 Status...11, 38 Stay Mode..4, 5, 8, 12, 13 Stop Recording..5 System Battery..36 T Test..8 Test Mode..6, 34 Time And Date..6 Trouble Messages..35 U User Codes..33 V Voice Announcement..3 Volume..5, 10, 11 W Wireless Keypads..3 Wireless Sensors..36 Z Zone Number..24 Zones... 4

SERVICING INFORMATION

Your local ADEMCO dealer is the person best qualified to service your alarm system. Arranging some kind of regular service program with him is advisable. Your local ADEMCO dealer is: Name: Address:

Phone:

WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example: Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. A user may not be able to reach a panic or emergency button quickly enough. While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death. Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90to 105 the detection performance can decrease. F, Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers. Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments.

ADEMCO ONE YEAR LIMITED WARRANTY
Alarm Device Manufacturing Company, a Division of Pittway Corporation, and its divisions, subsidiaries and affiliates ("Seller"), 165 Eileen Way, Syosset, New York 11791, warrants its security equipment (the "product") to be free from defects in materials and workmanship for one year from date of original purchase, under normal use and service. Seller's obligation is limited to repairing or replacing, at its option, free of charge for parts, labor, or transportation, any product proven to be defective in materials or workmanship under normal use and service. Seller shall have no obligation under this warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than the Seller. In case of defect, contact the security professional who installed and maintains your security equipment or the Seller for product repair. This one year Limited Warranty is in lieu of all other express warranties, obligations or liabilities. THERE ARE NO EXPRESS WARRANTIES, WHICH EXTEND BEYOND THE FACE HEREOF. ANY IMPLIED WARRANTIES, OBLIGATIONS OR LIABILITIES MADE BY SELLER IN CONNECTION WITH THIS PRODUCT, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, ARE LIMITED IN DURATION TO A PERIOD OF ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. ANY ACTION FOR BREACH OF ANY WARRANTY, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY, MUST BE BROUGHT WITHIN 12 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. Some states do not allow limitation on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Seller does not represent that the product may not be compromised or circumvented; that the product will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate warning or protection. Buyer understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, fire or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. No increase or alteration, written or verbal, to this warranty is authorized.

1 SW-1 ACTIVATES MODE SETTING

SW-6 SETS MODE

SWITCH DOWN FOR "OFF"
2-6 SETS HOUSE ID SHOWN SET FOR HOUSE ID# 12

01000-014-V1

Setting 5800RL DIP Switches
5827 WIRELESS KEYPAD DIP SWITCH TABLE
House ID 1 ------------------------------ON DIP SWITCH POSITIONS 4 ----------ON ----ON --ON ----ON ----ON ON --ON ON ON ----ON ----ON --ON ON --ON ON ON --ON ON --ON ON ON ON ON ON ------5 ON --ON --ON --ON --ON --ON --ON --ON --House ID ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON DIP SWITCH POSITIONS ------ON ----ON ------ON ON --ON ------ON --ON --ON ON ----ON ON ON ON ------ON ----ON ON --ON --ON --ON ON ON ON ----ON ON --ON ON ON ON --ON ON ON ON
5 SWITCH DOWN FOR "OFF"

HOUSE ID

SHOWN SET FOR HOUSE ID# 30

01000-013-VO

Setting 5827 DIP Switches

Mechanics of Programming

General Programming Information
Programming options are stored in non-removable, electrically erasable, nonvolatile EEROM memory. The system can be programmed at any time, even at the installer's premises prior to the actual installation. Simply apply power temporarily to the Control and then program the unit as desired. There are two programming modes: Data field programming (used for setting various system options) Interactive menu mode programming (used for programming zone information, programming Powerline Carrier
Devices, and for entering transmitter serial numbers) The system can also be programmed remotely, using an IBM Personal Computer, a modem, and Compass Downloader for Windows. See the Remote Programming/Control (Downloading) section.
Note: You may find it convenient to adjust the volume setting before entering the Program Mode. This will allow you to clearly hear the feedback announcements or system beeps in the Programming Mode, of the systems built-in speaker. To adjust the volume, press FUNCTION + VOLUME+ [3] or [6]. Upon exiting the Program Mode, the system will reset the volume to the default value (mid level).
Certain features differ between the LYNXR/LYNXR24 and the LYNXR-EN models. Verify the specific model being installed prior to the system programming.
exiting Programming mode, OR 2. After power-up, enter the Installer Code (4112) + 800 (This method disabled if Program mode is exited using 98.) to enter Expert Programming mode or Installer Code (4112) + 888 to enter Voice Prompt Programming mode.

Note: Keypad beeps if the zone is faulted when system is disarmed and Chime mode is on.

01000-020-V0

Type 09 Supervised Fire

Type 10 Interior w/Delay

Type 20 ArmStay

Type 21 ArmAway

Type 22 Disarm
Type 23 No Alarm Response Type 24 Silent Burglary

Data Field Descriptions

Defaults (where applicable) are Indicated in Text. The following pages list all data fields in this Control (in numerical order). Use the blank programming form to record the data for this installation. Note that both keypad LEDs flash while in Programming mode.
Note: Entering a number other than the one specified will give unpredictable results.

Installer Code

Enter 4 digits, 0-9
The Installer Code is used to enter the 4-digit Master Security Code. See "Master Code" in the System Operation section for procedure. If enabled, security code is not required to arm the system. The user simply presses and holds down the AWAY or STAY key to arm.

Quick Arm Enable

0 = do not allow quick arm 1 = allow quick arm

Keypad Backlight Timeout

0 = no timeout; always backlight keys 1 = turn backlighting off after inactivity
This option allows the choice of either always backlighting the keypad or turning the backlighting off after 10 seconds of keypad inactivity.

Forced Bypass

0 = no forced bypass 1 = provide automatic bypass of all open (faulted) zones
All zones bypassed by this function will be displayed after the bypass is initiated. Note: UL installations: must be 0 (no forced bypass) The House ID identifies receivers and wireless keypads. If a 5827 Wireless Keypad or 5804BD/5804BDV Transmitter is to be used, a House ID Code MUST be entered, and the keypad should be set to the same ID. Powerline Carrier Devices require a House ID. This field identifies this House ID to the Control. The Powerline Carrier Devices are programmed in field 80.

RF House ID Code

00 = disable all wireless keypad usage 01-31 = House ID
Powerline Carrier Device (X-10) House ID
0=A 1=B 2=C 3=D 4=E 5=F 6=G 7=H 8=I 9=J # + 10 = K # + 11 = L # + 12 = M # + 13 = N # + 14 = O # + 15 = P

Chime by Zone

Split/Dual Reporting

To Primary 0 = All reports 1 = Alarms, Restore, Cancel 2 = All except Open/Close, Test 3 = Alarms, Restore, Cancel 4 = All except Open/Close, Test 5 = All reports To Primary 6 = All reports except Open/Close 7 = All reports 8 = All reports 9 = All reports except Open/Close To Primary 10=All reports except Open/Close 11 = All reports 12=All reports 13=All reports except Open/Close To Secondary None, unless primary fails, then all Others Open/Close, Test All All All To Paging Number Alarms, Open/Close , Troubles Alarms, Troubles Alarms, Open/Close , Troubles Open/Close To Follow Me System Phone Number Alarms, Open/Close , Troubles Alarms, Troubles Alarms, Open/Close , Troubles Open/Close
This field is used to select a reporting option as follows: Enter: 0 - 5 when reporting to telephone receivers. 6 - 9 when reporting to a pager is desired. 10 - 13 when reporting to an auxiliary telephone receiver. Pager Report Format Options 6-9 send reports to the primary phone number, in a format defined in Field 48, and send reports to a pager, which has its phone number entered as the secondary phone number in Field 42. The pager report is a 7-digit code, with optional 16-digit prefix, in the following format: AAAAAAAAAAAAAAAA-EEE00NN where: AAA = Optional 16 digits for PIN number, etc. See Field 88 for full description of these characters. EEE = 3-digit Event Code as follows: 911 = Alarm (NN = zone number) 101 = Open, system disarmed (NN = user no.) 102 = Close, system armed (NN = user no.) 811 = Trouble (NN = zone no.) 00 = Always displayed before 2-digit user/zone no. NN = 2-digit user number or zone number, depending on the type of event (EEE) that occurred. NN=00 indicates AC loss, system low battery, or low battery in 5827. Follow Me System Report Format Options 10-13 send reports to the primary phone number, in a format defined in Field 48, and sends voice message to the secondary phone number entered in Field 42. The message is a repeatable system status announcement. If the manual paging option has been programmed in Field 87, the message will repeat system, system. The message can be terminated by pressing any key on the telephone keypad.
Will report Users 0, 5-8, and, if using wireless button-type devices, will report the zone number of the arm or disarm button 26-33. All other zones and users are not reported.
15-Second Dialer Delay (Burglary)
0 = no dialer delay 1 = provide 15-second delay of burglary alarm report when armed away
If enabled, provides communication delay to the central station and allows the subscriber time to avoid a false alarm transmission. Delay does not apply to zone type 6, 7, 8, and 9 alarms, which are always sent as soon as they occur. UL installations: must be 0 (no delay) Test report code entered in field 64 is sent.

SYSTEM STATUS REPORT CODES (5968)

Exit Error Report Code

(See notes above)
If the system is armed and an entry/exit or interior zone is still open after the exit delay time has expired, an alarm will sound at the keypad and external sounder. If the system is disarmed before the end of the entry delay that immediately follows, the alarm sounding will stop and no message will be sent to the central station. The keypad will display CA (CANCELED ALARM). If the system is not disarmed before the end of the entry delay mentioned above, and an entry/exit or interior zone is still open, an exit alarm message will be sent to the central station if an Exit Error report code is selected in this field. The keypad will display EA (EXIT ALARM), and the alarm sounding will continue until the system is disarmed (or timeout occurs). An Exit Alarm condition will also result if a fault occurs in an exit or interior zone within 2 minutes following the end of the exit delay, and an Exit Alarm message will be sent to the central station. If Contact ID format has been programmed, the message will contain the zone number and error code 374 (TroubleExit Error). If 4+2 format is used, the digit entered in this field will be sent followed by the second digit of the programmed alarm code for that zone. If 3+1 or 4+1 format is used, only the digit entered in this field will be sent. This message will go to the primary phone no. Under any of these conditions, no restore message will be sent. If 0 is entered in this field, no special message will be sent, only the regular alarm and alarm restore code for the zone. This will be sent if a zone goes into trouble. This will be sent when a zone is manually bypassed. Timing of this report is random with up to a 4-hour delay. If AC restores before the report goes out, there is no AC restore report. This will be sent when a low battery condition exists in the systems standby battery. This is sent periodically to test that the communicator and phone lines are operational (frequency of report is selected in field 51). This is sent upon disarming of the system. 2nd digit = user number, if expanded or 4+2 reporting is selected. This option allows for independent programming of AWAY and STAY reports. 2nd digit of report is user number if expanded or 4+2 reporting is selected. NOTE: OPEN reports are not sent if the associated closing report is not enabled. This is sent in the event that a wireless transmitter low battery condition exists. This is sent upon disarming of the system after an alarm condition was reported.
Trouble Report Code (See notes above) Bypass Report Code (See notes above) AC Loss Report Code (See notes above) Low Battery Report Code (See notes above) Test Report Code (See notes above) Open Report Code (See notes above) Arm AWAY/STAY Report Code (See notes above)

LYNX must be connected to the telephone line, if using the Back-up reporting option.
Wireless Dialer Setup If the wireless dialer is enabled in Field 55, Lynx automatically sends the setup information to the wireless dialer immediately after exiting the programming mode. Lynx will confirm that the 5842 wireless dialer has successfully received the setup information by generating three beeps. If the setup information has not been successfully received by the wireless dialer the Lynx will generate a single beep once per minute and Fault Zone 93 will be displayed. To prepare the dialer for setup refer to the Installation Instructions provided with the 5842 Wireless Dialer.
Note: 1. It takes about 95 seconds for Lynx to transmit the setup information after power has been applied to the control. 2. Entering Programming mode may take up to 18 seconds if the 5842 Wireless Dialer has been enabled. The system will display - - until the Lynx enters Programming mode.
You must refer to these instructions or to the Programming Guide while programming the system because the keypad display does not show prompt titles. Instead, prompts are indicated by a number/letter combination. The prompts for 55 are as follows: Ed Er Ln Eb Enable Dialer.. for enabling the 5842 wireless dialer. Enable Trouble/Supervisory Reports. for defining wireless dialer response to events.* Response to Phone Line Failure. for defining console sounder response (trouble/alarm) to a phone line cut. Enable Back-up Reporting. for enabling the Lynx as a backup dialer.
*The Contact ID Event Codes for the reports associated with the 5842 wireless dialer include the following: 145 Wireless Dialer Tamper (Alarm) 338 Wireless Dialer Low Battery 341 Wireless Dialer Tamper (Trouble) 342 Wireless Dialer AC Loss (if supported by the 5842 Wireless Dialer being installed) 351 Wireless Dialer Phone Line Cut (if supported by the 5842 Wireless Dialer being installed) 355 (Zone 93) Wireless Dialer Loss of RF Supervision 355 (Zone 000) Interruption of RF Link reported by the 5842 Wireless Dialer For additional information refer to the Contact ID Event Codes table.

01-41, 95, 96, 99 = Zone number [] = continue 00 = exit Zone Programming mode
Enter the 2-digit zone number to be programmed and the Voice Descriptor for the selected zone number will be announced, if it is programmed. Press [] to advance.
Zone 01 = hardwire Zones 02-25 = RF zones (only) Zones 26-41 = Button zones (only) Zone 92 = Duress Zones 95, 96, 99 = Panic zones
Pressing 00 exits mode, upon which the prompt 56 blinks, indicating the mode is inactive. Press [] + any field number to go to that field.

Zone type

00-24 = zone type [] = continue [#] = return to previous prompt
Note: If 00 is accepted as a zone type, save the 00 zone type and advance to the confirm delete prompt (F).
Each zone must be assigned to a zone type, which defines the way in which the system responds to faults in that zone. Enter the 2-digit zone type for this zone as follows: 00 = Not Used 08 = 24 Hr Aux 01 = Entry/Exit #= Fire without verify 02 = Entry/Exit #= Interior w/Delay 03 = Perimeter 20 = ArmStay 04 = Interior Follower 21 = ArmAway 05 = Trouble Day/Alarm Night 22 = Disarm 06 = 24 Hr Silent 23 = No Alarm Response 07 = 24 Hr Audible 24 = Silent Burglary The report code consists of 2 hexadecimal digits, each in turn consisting of 2 numerical digits. For example, for a report code of "3C", enter [0][3] for "3" and [1][2] for "C". If this is Zone 1, 95, 96 or 99, the system skips to the VOICE DESCRIPTOR prompt (1C). Enter the input type for the transmitter assigned to this zone. Refer to the transmitters instructions for input types of each transmitter. Note: Zones 2-25 should be assigned Input Type 3 or 4. Zones 26-41 should be assigned Input Type 5 only.

Report code

Enter the report code for this zone. [] = continue [#] = return to previous prompt

Input type

3 =RF (supervised RF) sends periodic check-in signals, faults, restore and low battery signals
Note: RF type transmitters must remain within range of the receiver, otherwise a supervision failure signal will occur.
4 = UR (unsupervised RF) sends same as RF type, but control does not supervise the check-in signals 5 = BR (button type) sends only fault and low battery signals; does not send restores or check-in signals

Enter the first word of the descriptor for the selected zone. Use the [6] or [8] key to advance as described. To change the entered index number before pressing [6] or [8], simply press [#] + desired 2-digit vocabulary index number. If descriptor 1 is not desired, enter [#] + 99 (blank), then press [8] to return to zone number prompt.
Enter [#] + 2-digit vocabulary index number of second descriptor word for this zone. 6 = accept word and advance to descriptor 3 (descriptor 3 will be announced) 8 = accept word and advance to prompt (A) for next zone. Press any other key to repeat the selected word.
Enter the second word of the descriptor for the selected zone. Use the [6] or [8] key to advance as described. To change the entered index number before pressing [6] or [8], simply press [#] + desired 2-digit vocabulary index number. If descriptor 2 is not desired, enter [#] + 99 (blank), then press [8] to return to zone number prompt.
Enter [#] + 2-digit vocabulary index number of third descriptor word for this zone. 6 or 8 = accept word and advance to prompt (A) for next zone. Zone descriptor will be announced. Press any other key to repeat the selected word.
Enter the last word of the descriptor for the selected zone. Use the [6] or [8] key to advance as described. To change the entered index number before pressing [6] or [8], simply press [#] + desired 2-digit vocabulary index number. If descriptor 3 is not desired, enter [#] + 99 (blank), then press [8] to return to zone number prompt.
84 Assign Zone Voice Descriptor

VOICE VOCABULARY INDEX

00 second pause A ALARM ATTIC B BABY BACK BASEMENT BATHROOM BEDROOM C CHECK D DELAY DOOR DEN DETECTOR DINING DINING ROOM DOOR DOWNSTAIRS DRIVEWAY E EAST EIGHT EMERGENCY F FAMILY ROOM FIRE FIRE DETECTION FIRST FLOOR FIVE FLOOR FOUR FRONT G 48 GARAGE 49 GUEST ROOM 09 GUN H HALL I INSIDE K KITCHEN L LAUNDRY LAUNDRY ROOM LIBRARY LIVING LIVING ROOM P 61 PATIO 62 POLICE 18 POOL R 63 REAR 19 ROOM S SECOND FLOOR SEVEN SHED SHOP SIDE SILENT POLICE SIX SLIDING SMOKE SOUTH STORAGE SYSTEM T THIRD FLOOR THREE TRANSMITTER TWO 99 Z ZERO ZONES 1ST 2ND 3RD Custom Word #1 Custom Word #2 Custom Word #3 Custom Word #4 Custom Word #5 Blank (for erasing a previously programmed word) SYSTEM WORDS AC LOSS ARMED AWAY BYPASSED CHIME DISARMED DISARM SYSTEM NOW EXIT NOW FAULT INSTANT LOW BATTERY NOT READY TO ARM STAY

key: Used to scroll backward
through menu choices. 7. FUNCTION/ #
key: Used to repeat a voice prompt. (This function cannot be used while entering phone or account numbers.)
Notes: (1) Keying in any new command will terminate the active voice prompt. (2) If an irrelevant command is entered LYNXR will generate a long rejection beep and repeat the previous voice prompt. (3) Phone numbers and account numbers can be left blank by pressing the ADD/ AWAY key without entering any data. (4) LYNXR automatically saves phone and account number data once all available digits are entered.
ENTERING VOICE PROMPT PROGRAMMING
1. 2. Power-up the control and enter the Installer Code (1 2) + 8. Once you have entered into the Voice Prompt Programming Mode the system will announce, Programming, use ARROWS to scroll choices, press SELECT to accept, press ESCAPE to quit. Press the 6 5. Follow the directions provided by each voice prompt to make your selections.
The FUNCTION/ # prompt, as required. key can be used to repeat a voice
or 3 keys to scroll through the voice
When you have completed each programming procedure the system will return to the Main Programming Menu.
menu and follow the instructions provided. The system will announce the following options: Add Sensors Delete Sensors First Central Station Phone Number First Central Station Account Number Second Central Station Phone Number Second Central Station Account Number Templates Expert Programming Mode
EXITING VOICE PROMPT PROGRAMMING
1. Once you have returned to the Main Programming Menu, the system will announce, Programming use ARROWS to scroll choices, press SELECT to accept, press ESCAPE to quit. Press ESCAPE/ OFF to exit Voice Prompt programming
mode once you have returned to the Main Programming Menu.
Enter Voice Prompt Programming Mode: (Installer Code + 8). Follow the voice prompts to advance to the selected item in the Main Programming Menu.
Add Sensors First Central Station Phone Number Second Central Station Phone Number Templates

To Add First Central Station Account Number
Select "First Central Station Account Number" Enter first central station account number (up to 4 or 10 digits)
To Add Second Central Station Phone Number
Select "Second Central Station Phone Number" Enter second central station phone number (up to 24 digits) Enter second central station account number (up to 4 digits)
To Add Second Central Station Account Number
Select "Second Central Station Account Number" Enter second central station account number (up to 4 or 10 digits)
Refer to the LYNXR Series Installation and Setup Guide to view the complete set of Template (default table) selections.
To Program a Template (Default Table)
Select "Templates" Select template
(6) Template selections Template 1 Template 2 Template 3 Template 4
To Enter Expert Programming Mode
Once you have entered the Expert Programming Mode, the [ESCAPE] key can be used to return to the Voice Prompt Programming mode.
Select "Expert programming mode"
System switches to Expert Programming Mode (Refer to the LYNXR Series Installation and Setup Guide or the LYNXR Series Programming Guide for additional programming instructions)
Remote Programming/Control (Downloading)
The control panel can be remotely programmed from an IBM-compatible Personal Computer (PC), a HAYES Modem, and ADEMCOs Compass Downloader for Windows (as specified below).
Downloading may only be performed if a technician is at the site.
Multiple security levels protect remote programming against compromise by attempts to defeat the system. 1. Security Code Handshake: An 8-digit download ID code must be matched between the Control and downloader. 2. Site-Initiated Remote Programming: The installer or subscriber initiates the call from the subscriber premises (by entering Installer Code + # + 1) while disarmed. All parameters can then be downloaded via the phone lines using a personal computer. 3. Station-Initiated Remote Programming: The operator calls the site from your office to initiate the download call. The Control hangs up and then calls back the PC via the preprogrammed telephone number. The unit can then be uploaded, downloaded, or controlled from your office. 4. Telco Handoff: The installer or subscriber performs a download session on the call initiated from the site or from local laptop computer (by entering Installer or Master Code + # + 1 at the control panel). 5. Data Encryption: Data passed between the PC and the Control is encrypted for security so that it is very difficult for a foreign device tapped into the phone line to take over communication and substitute system-compromising information. Equipment required to download to a system at the premises An IBM PC compatible computer and appropriate interconnecting cables. Either a HAYES brand SMARTMODEM 1200 (Level 1.2 or higher external or Level 1.1 or higher [with 4 position DIP switch] internal style), a HAYES brand Optima 336 external, a HAYES brand Optima 24 Plus FAX96, or an Ademco CIA Modem. Compass Downloader for Windows (at revision level supporting LYNXR, LYNXR24 or LYNXR-EN). Initial Download: Enter Installer Code + # + 5. This sets field 95 to 4 rings, and system to no call-back option. The download computer can then call the subscriber, make connection, and download all programming data. Flexible Callback: If enabled in field 93, the download operator can temporarily change the last 1, 2, or 3 digits (depending on selection) of the call back number. This allows the control to call back a computer other than the one programmed, which may be helpful at times of high computer traffic. See field 93 for a full description.

Does not arm properly. READY light not on. Open or faulted zone(s) Check for faulted zones and make intact, or use Bypass arming, if desired.
System doesn't respond to keystrokes on keypad. 4a. "CC" displayed. 4b. "d1" displayed. 4a. System is in communication with downloader at central station. 4b. System has just been powered and is in its one minute initialization. 4a. Wait until download session is finished. 4b. Wait for initialization to finish, or bypass this time by pressing '#' + '0.'

SMOKE DETECTOR

1. Detector alarms, no apparent reason.
1a. Dust, dirt in sensing chamber. 1b. Improper location. 1c. Unit malfunctioning.
1a. Clean unit's sensing chamber with vacuum cleaner per unit's instructions. 1b. See unit's instructions for locations to avoid. Relocate as necessary. 1c. Replace detector. 2a. Check for proper installation of battery. Try new battery. 2b. Replace detector.

Detector's siren sounds.

2a. Unit not receiving required power. 2b. Unit malfunctioning.
Contacting Technical Support
PLEASE, before you call Technical Support, be sure you: READ THE INSTRUCTIONS! Check all wiring connections. Determine that the power supply and/or backup battery are supplying proper voltages. Verify your programming information where applicable. Note the proper model number of this product, and the version level (if known) along with any documentation that came with the product. Note your ADEMCO customer number and/or company name. Having this information handy will make it easier for us to serve you quickly and effectively. You may contact Technical Support via Toll Free Fax. Please include your return fax number. You will receive a reply within 24 hours. Technical Support:... 1-800-645-7492 (8 a.m.-8 p.m. E.S.T.) FAX FAXBACK Automated Fax Retrieval System:.. 1-800-573-0153 or 1-516-921-6704 / ext. 1667
World Wide Web Address:... http://www.ademco.com
Regulatory Agency Statements
UL NOTICE: This is a "Grade A" residential system.
FCC ID: CFS8DLLYNXREN-2 CANADA: 1748A-LYNXREN2

FCC STATEMENT

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Federal Communications Commission (FCC) Part 15 Statement

(boldface indicates defaults that differ between tables) Table 1 Table 2 Table 3 Table 0 0,0 0,0 0,0 0,1 4,10 4,10 4,10 4,10 1,5 1,5 1,5 1,1 7,0 6,0 7,0 7,0 3,0 4,5 3,0 3,0 6,0 6,0 6,0 6,0 1,1 0,1 1,1 1,1 ------------------------15,15,15,15 15,15,15,15 15,15,15,15 15,15,15,15 ----------------7,7 7,7 7,7 7,0 0, 0, 0, 0 0, 0, 0, 0 0, 0, 0, 0 0, 0, 0, 0 See *56 table See *56 table See *56 table See *56 table 1,0 1,0 1,0 1,0 0,0 0,0 0,0 0,0 0,0 0,0 0,0 0,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 0,0 0,0 0,0 0,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,1 1,0 1,0 1,0 1,0 0,0 0,0 0,0 0,0 0,0 0,0 0,0 0,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 0,0 1,0 0,0 0,0 See *80 table See *80 table See *80 table See *80 table See *81 table See *81 table See *81 table See *81 table Refer to *84 Programming --------0,0 0,0 0,0 0,0 --------1,2,3,4 1,2,3,4 1,2,3,4 1,2,3,4 ---------
LYNXR-EN PROGRAMMING DEFAULT TABLES
(boldface indicates defaults that differ between tables) Function *20 Installer code *21 Quick arm enable *22 Keypad backlight timeout *23 Forced bypass *24 RF house ID code *25 Powerline carrier device house code *26 Chime-by-zone *27 Real-time clock display *29 Daylight saving time start/end month *30 Daylight saving time start/end weekend *31 Single alarm sounding per zone *32 Fire sounder timeout *33 Alarm bell timeout *34 Exit delay *35 Entry delay 1 (zone type 01) *36 Entry delay 2 (zone type 02) *37 Audible exit warning/quick exit *38 Confirmation of arming ding *39 Power up in previous state *40 PABX access code *41 Primary phone number *42 Secondary phone number *43 Primary subscriber account number *44 Secondary subscriber account number *46 Follow Me Reminder Phone Number *47 Phone system select *48 Report format *49 Split/dual reporting *second dialer delay (burglary) *51 Periodic test report *52 First test report offset *53 Sescoa/radionics select *54 Lack of usage notification *55 Wireless Dialer *56 Enhanced Zone programming *58 RF jam detection *59 Exit error report code *60 Trouble report code *61 Bypass report code *62 AC loss report code *63 Low battery Report code *64 Test report code *65 Open report code *66 Arm away/stay report code *67 RF transmitter low battery report code *68 Cancel report code *70 Alarm restore codes *71 Trouble restore report code *72 Bypass restore report code *73 AC restore report code *74 Low battery restore report code *75 RF transmitter low battery restore report code *76 Test restore report code *80 Powerline Carrier Devices *81 Zone lists for devices *84 Assign zone voice descriptors *87 Auxiliary Function/ 1-button paging *88 Pager characters *89 Event log 80% full report code *90 Event logging *91 Alarm audio verification/remote phone control *92 Number of reports in armed period *93 Flexible call back *94 Download phone number *95 Ring detect count for downloading/remote phone control Default Master Code Default Duress Code By activating *96, Field 43, and 44 will be changed to 15, 15, 15, 15. Table 0 0,4,10 1,7,0 3,0 6,0 1,1 ------15,15,15,15 ----5 7,0 0, 0, 0, 0 See *56 table 1,0 0,0 0,0 1,0 1,0,0 1,0 1,1,0 0,0 0,0 1,0 1,0 0,0 See *80 table See *81 table 0 --0,0 --15 1,2,3,4 --Table 2 Table 0 0,0 0,1 4,10 4,10 1,5 1,1 6,0 7,0 4,5 3,0 6,0 6,0 0,1 1,1 ------------15,15,15,15 15,15,15,15 --------7,7 7,0 0, 0, 0, 0 0, 0, 0, 0 See *56 table See *56 table 1,0 1,0 0,0 0,0 0,0 0,0 1,0 1,0 1,0 1,0 0,0 0,0 1,0 1,0 1,0 1,1 1,0 1,0 0,0 0,0 0,0 0,0 1,0 1,0 1,0 1,0 1,0 0,0 See *80 table --See *81 table See *81 table Refer to *84 Programming ----0,0 0,0 ----1,2,3,4 1,2,3,4 ----Table 0 0,4,10 1,7,0 3,0 6,0 1,1 ------15,15,15,15 ----5 7,0 0, 0, 0, 0 See *56 table 1,0 0,0 0,0 1,0 1,0,0 1,0 1,1,0 0,0 0,0 1,0 1,0 0,0 See *80 table See *81 table 1 --0,0 --15 1,2,3,4 ---

56 ZONE ASSIGNMENT/ALARM REPORT CODES FOR TABLE 1 Zone No. Zone Type Alarm Code Input Type Loop Number Zone Descriptor 0,0 ----1,(RF) 2 47, 04 (FRONT DOOR) 1,(RF) 2 33, 04 (BACK DOOR) 1,(RF) (WINDOW) 1,(RF) (MOTION DETECTOR) 1,(BR) 22 1,(BR) 20 1,(BR) 23 0,(BR) 21 1,(BR) 22 1,(BR) 20 1,(BR) 23 0,(BR) --1,0 ----1,0 ----NOTE: Zone 1 is a hardwire zone; Zone 2 to 41 are RF zones; Zone 92 is Duress; Zone 99 is keypad panic 56 ZONE ASSIGNMENT/ALARM REPORT CODES FOR TABLE 2 Zone No. Zone Type Alarm Code Input Type Loop Number Zone Descriptor 0,0 ----1,(RF) 2 47, 04 (FRONT DOOR) 1,(RF) 2 33, 04 (BACK DOOR) 1,(RF) 2 48, 04 (GARAGE DOOR)) 1,(RF) (MOTION DETECTOR) 1,(RF) 1 22, 02 (SMOKE DETECTOR) 1,(BR) 22 1,(BR) 20 1,(BR) 23 0,(BR) 21 1,(BR) 22 1,(BR) 20 1,(BR) 23 0,(BR) --1,0 ----1,0 ----1,0 ----1,0 ----NOTE: Zone 1 is a hardwire zone; Zone 2 to 41 are RF zones; Zone 92 is Duress; Zone 99 is keypad panic 56 ZONE ASSIGNMENT/ALARM REPORT CODES FOR TABLES 3 & 4 Zone No. Zone Type Alarm Code Input Type Loop Number Zone Descriptor 0,0 ----1,(RF) 2 47, 04 (FRONT DOOR) 1,(RF) 2 33, 04 (BACK DOOR) 1,(RF) (WINDOW) 1,(RF) (WINDOW) 1,(RF) (WINDOW) 1,(RF) (WINDOW) 1,(RF) (MOTION DETECTOR) 1,(RF) 1 22, 02 (SMOKE DETECTOR) 1,(BR) 22 1,(BR) 23 0,(BR) 23 0,(BR) 21 1,(BR) 22 1,(BR) 23 0,(BR) 23 0,(BR) --1,0 ----1,0 ----NOTE: Zone 1 is a hardwire zone; Zone 2 to 41 are RF zones; Zone 92 is Duress; Zone 99 is keypad panic
80 DEFAULT TABLE: APPLIES TO DEFAULT TABLE 4 (devices 2-7 have no default values) Start Zone Type Restore of Device Number Action Event Zone List System Operation Zone List

1 8** 33 2

Stop Zone type System operation
** NOTE: If using an X-10 Powerhouse Security SH10A siren as device 8, you must change the device action default to 3 if using default table 4. 80 DEFAULT TABLE: APPLIES TO DEFAULT TABLE 1 and 2 (devices 1-7 have no default values) Start Stop Zone Type Restore of Zone type Device Number Action Event Zone List System Operation Zone List System operation

8** 36

81 ZONE LIST FOR OUTPUT DEVICES DEFAULT TABLE: Applies To Default Table 1 - 4. Zone List 1 28, 32 Zone List 2 29, 33 Zone List 3 2, 3

Index

*55 Enabling the 5842 Wireless Dialer.. 25 *56 Enhanced Zone Programming Mode.11, 20, 24, 27 *80 Device Programming Menu Mode..24, 31, 32, 33 *81 Zone List Menu Mode.. 24, 34 *83 Enhanced Sequential Mode. 24, 27, 29, 30, 35, 36, 37 *84 Assign Zone Voice Descriptors..24, 30, 38, 39 *85 Record Custom Voice Descriptors. 24, 40 *96 Initialize Download ID And Subscriber Acct. No. For Downloading.. 24 *97 Set All Program Fields To 1 Of 4 Sets Of Default Values 24 *98 Exits Programming Mode.. 24 *99 Exits Programming Mode.. 24 1.2-Volt Nickel-Metal Hydride Batteries.. 10 1332CN... Second Dialer Delay.. 20, 61, 62 24-Hour Audible Alarm... 16 24-Hour Auxiliary Alarm.. 16 24-Hour Silent Alarm... 15, Series Transmitters... 11 5800RL... 11, 13 5801... 11 5802MN... 11, 12 5802MN2.... 12 5804... 11, 12, 35 5804BD... 11, 12, 17 5804BDV... 11, 12, 17 5804E... 11, 12 5804WATCH... 11 5816... 11, 35 5817... 11 5827... 11, 13, 17 5828V.... 13 5842... 25 90... 52 A AC Loss Report Code... 21, 61, 62 AC Power... 9 AC Power and Rechargeable Backup Battery.. 10 AC Power Loss... 9 AC Restore Report Code.. 61, 62 AC Transformer... 6 ADEMCO 1332/1332X10... 9 ADEMCO Express... 19, 60 ADEMCO Low Speed.. 19, 60 Alarm Audio Verification (AAV)/Remote Phone Control. 23 Alarm Audio Verification (Two-Way Voice Feature).. 50 Alarm Bell Timeout... 17, 61, 62 Alarm Output.... 4 Alarm Restore Codes.. 61, 62 Alarm Restore Report Code... 21 Alarm Sounder... 60 Arm Away/Stay Report Code.. 61, 62 Arm AWAY/STAY Report Code.. 21 ArmAway... 16 Armed System Test... 53 ArmStay... 16 Assign (Or Change) A Secondary Security Code. 47 Assign Custom Voice Descriptors.. 40 Assign Zone Voice Descriptors.. 38, 61, 62 Audible Exit Warning/Quick Exit. 18, 61, 62 AUX Function... 48 AUX Function/1-Button Paging.. 22, 61, 62 AUX Key.... 22 AWAY Mode.... 48 B Babysitter Code..47 Back Plate...5 Backlighting....17 Backup Battery...9 Backup Reporting...18 Battery Life...12 Battery, Low....52 Bell....60 BR....11, 28 Burglary Zones...17 Busy-Standby...52 Button Transmitters...11, 12 Button Type...28 Button Zones...26, 28 Bypass Report Code..21, 61, 62 Bypass Restore Report Code..21, 61, 62 C CA Message Display...51 Callback Number...23 Cancel Report Code..61, 62 Canceled Alarm..21 CC...52 Change the Master Code...47 Chime By Zone...17, 61, 62 Chime Mode..17, 48 Closing Report...18 Comm. Failure...52 Communication...4, 54 Compass Downloader...45 Confirmation of Arming Ding..18, 61, 62 Connecting AC Power and Backup Battery.9 Contact ID...54 Contact ID Event Codes...55 Contact ID Format...21, 47 Contact ID Reporting..55, 60 Contacting Technical Support..58 Custom Descriptor Number...40 Custom Voice Descriptors..24, 40 D Data Encryption...45 Data Field...14 Daylight Savings Time Start/End..17, 61, 62 Daylight Savings Time Start/End Week..17 Default Master Code...61, 62 Default Tables...61, 62 Delete a Secondary Security Code..47 Delete Entire Zone List..34 Delete Zone Parameters Confirmation..29, 37 Delete Zones....34 Descriptor...30, 38 Desktop Mounting...5 Device Action...33 Device Number...33 DI Display...52 DIP Switches...11 Disable Local Sounder...7 Disarm...16, 48 Displays...52 Download Call Back Phone Number..23 Download Phone Number...61, 62 Download, Initial...45 Downloader..22, 45, 46 Duress Code..47, 63