/<1;5/<1;5

6HFXULW\6\VWHPV

8VHU*XLGH

OFF AWAY STAY AUX

K5481V1 9/01

7$%/(2)&217(176
SYSTEM OVERVIEW....3 Features.....3 General Operation.....4 Quick View of System Functions....6 About the Master Keypad....7 About the Display and Indicators....8 Master Keypad Definitions....9 SECURING THE PREMISES....11 Checking System Status....11 Arming the System....12 Entry/Exit Delays.....14 Disarming the System.....15 Bypassing Protection Zones.....16 Panic Keys / Chime Mode....17 USER FUNCTIONS.....18 Paging Feature....18 Using Powerline Carrier Device Commands (Lights On/Lights Off keys)..19 Message Recording/Playback/Volume Control...20 Aux Function.....21 Clock/Calendar.....22 Scheduling User Interface....23 Remote Phone Control Feature....28 FIRE ALARM SYSTEM....30 General Information.....30 National Fire Protection Associations Smoke Detector Recommendations..31 Emergency Evacuation....32 SYSTEM FUNCTIONS....33 Security Codes....33 Testing the System.....34 Trouble Messages....35 Maintaining Your System....36 SUMMARY OF AUDIBLE NOTIFICATION....37 FCC STATEMENTS....38 OWNERS INSURANCE PREMIUM CREDIT REQUEST...39 INDEX.....41 LIMITATIONS OF THIS ALARM SYSTEM....43 ONE YEAR WARRANTY....44 Congratulations on your ownership of an ADEMCO Security System. You have made a wise decision in choosing it, for it represents the latest in security protection technology today. ADEMCO is the world's largest manufacturer of security systems, and millions of premises are protected by ADEMCO products.

6<67(029(59,(:

General Information

Features

This system offers you three forms of protection: burglary, fire, and emergency, depending on the configuration of your system. The system consists of a master keypad for controlling system operation, various wireless sensors which provide perimeter and interior burglary protection, and optional smoke or combustion detectors to provide early fire warning. In addition, optional wireless keypads may have been installed to allow you to control the system away from the master keypad. The system uses microcomputer technology to monitor all protection zones and system status, display appropriate information on the keypad display, and initiate appropriate alarms. Your system may also have been programmed to automatically send alarm or status messages over the phone lines to a central alarm monitoring station. The user features of this security system are listed below. Ask your installer which features have been programmed for your system. STAY and AWAY arming modes: You can protect either the perimeter only, or the entire premises. 3 panic key functions: Designated keys allow you to manually activate fire, personal emergency, or silent alarms. Refer to the PANIC KEYS section for detailed information. Paging feature: Alerts you to certain system conditions by displaying code numbers that indicate the type of condition that has occurred. In addition, pressing the AUX key can send a predefined message to your pager, if programmed to do so (see AUX key function below). Refer to the PAGING FEATURE section for detailed information. Real-time clock: Keypad displays current time. Refer to the CLOCK/CALENDAR section for procedures for setting the time. Voice announcement of system status: The master keypads built-in speaker announces system status at the press of a key. Refer to the CHECKING SYSTEM STATUS section for details. Message center: The system allows recording and play back of brief messages. Refer to the RECORDING/ PLAYBACK MESSAGES section for procedures. Device activation: Designated keys allow you to turn lights and/or other devices on and off. In addition, some devices (e.g., a light) may be programmed to activate automatically as a result of a system event such as an alarm or trouble condition. Refer to the USING DEVICE COMMANDS section for detailed information. AUX key function: Designated key lets you activate a predefined series of keystrokes with a single press of the AUX key plus user code, if programmed to do so (see Paging feature above). Refer to the AUX FUNCTION section for detailed information. Scheduling feature: Allows you to schedule the automatic activation or deactivation of X-10 devices or program events (e.g. alarm clock, reminder, and latch key). Phone Control: Provides a remote interactive phone capability that permits access to the security system from any off-site touch-tone telephone. Security Codes: The system is capable of supporting an Installer code, Master user code and six additional User codes. Refer to the SECURITY CODES section for detailed information. 3

+ [6] + [#]* + [9]

+ FUNCTION + FUNCTION +

LIGHTS ON

+ [63] + [64]
LIGHTS OFF + device number
+ FUNCTION + LIGHTS ON or LIGHTS OFF + dev. no.

** + ** + + +

CODE CODE
+ user no. (02-08)+ user code + user number (02-08)

TEST OFF

To use the defined AUX function: ----------- Press and hold AUX key 2 secs (4 beeps) + To send message to pager: -------------------- Press and hold AUX key 2 seconds (4 beeps) ** Only the master code can be used to add or delete another user code.

About the Master Keypad

General
IMPORTANT: If the keypad beeps rapidly upon entering the premises, an alarm has occurred during your absence and an intruder may still be on the premises. LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location. The keypad allows you to control all system functions. The keypad features telephone-style keys and a Liquid Crystal Display (LCD), which shows the nature and location of all occurrences.

BYPASS

LIGHTS OFF STATUS

FUNCTION

01000-021-V0
The keypad also features a built-in sounder, which will sound during alarms and troubles. The keypad also "beeps" during certain system functions, such as during entry/exit delay times, in Chime mode, and when depressing any of the keys (to acknowledge the key press). In addition, a built-in speaker announces system status.
About the Display and Indicators
Display Definitions (for other displays, see Trouble Messages)
ALARM: Appears when an intrusion has been detected and the system is armed (also appears during a fire alarm or AWAY LOW BAT AC INSTANT CHIME TEST audible emergency alarm). Accompanied by the STAY REC MESSAGE protection zone in alarm. ALARM FIRE BYPASS FAULT All burglary zones, interior and perimeter, are armed. Entry delay is turned off. Perimeter burglary zones, such as protected windows and doors, are armed.

AWAY: INSTANT: STAY:

LOW BAT:
AC: CHIME: TEST: REC: MESSAGE: BYPASS: FAULT:
Appears when a fire alarm or fire fault is present. Accompanied by a display of the zone in alarm. Low battery condition in a wireless sensor (if zone number is displayed) or low system battery (if no zone number is displayed). If 00 is displayed, a wireless keypad (5827) has a low battery condition. Appears when AC power is present. If not lit, the system is operating on backup battery power. Appears when the Chime feature is activated. Appears when the system is in Test mode. Appears when in Recording mode. Appears when a message has been recorded and has not yet been played back. One or more burglary protection zones have been bypassed. Appears when a malfunction is discovered in the system at any time; or if an open is detected in a fire zone at any time; or when a fault in a day/night burglary zone is discovered during a disarmed period. Accompanied by a display of the zone number in trouble. Appears during a remote phone control session.

+ AWAY or STAY + NO DELAY

Quick Arming

If Quick Arm was programmed by the installer, you do not need to enter the security code to arm the system. Instead, simply press and hold down the desired arming key for at least 2 seconds. The security code must always be used to disarm the system, however. To arm if Quick Arm is active: AWAY or STAY hold down for at least 2 seconds To arm with NO DELAY if Quick Arm is active: AWAY or STAY then NO DELAY hold down for at

least 2 seconds

IMPORTANT: The Babysitter Code and Installer Code cannot disarm the system unless it was used to arm the system. In addition, if the system is armed by pressing and holding the Quick-Arm buttons, neither the Babysitter Code nor Installer Code can disarm the system.

Entry/Exit Delays

Exit Delay
Exit delay begins immediately after arming the system, and gives you time to leave through the designated exit door without setting off an alarm. A slow beeping will sound throughout the exit delay period, if programmed. Exit Alarms Exit Alarm Active To minimize false alarms sent to the alarm monitoring company, your system may have been programmed for this feature. Ask your installer if Exit Alarm is active for your system. Whenever you arm the system, the exit delay begins. If an entry/exit door or interior zone is faulted when the exit delay ends (e.g., exit door left open), the system sounds an alarm and starts the entry delay timer. If you disarm the system before the entry delay ends, the alarm sound stops and the message "CA" is displayed on the keypad, along with a zone number indicating the faulted zone. No message is sent to the alarm monitoring company. To clear the exit alarm condition, the open zone must be made re-secured; to clear the display, enter your code plus OFF. If you do not disarm the system before the entry delay ends, and an entry/exit door or interior zone is still open, the alarm sound continues and an "exit alarm" message is sent to the alarm monitoring company. The message "EA" is displayed on the keypad, along with a zone number indicating the faulted zone. To stop the alarm, the system must be disarmed (your code plus OFF); to clear the display, enter your code plus OFF a second time. An exit alarm also results if an entry/exit door or interior zone is faulted within two minutes after the end of the exit delay.

Entry Delay

Entry Delays give you time to disarm the system when you re-enter through the designated entrance door. You must disarm the system before the entry delay period ends, or an alarm will occur. The keypad beeps during the entry delay period, reminding you to disarm the system. There are two entry delays (if programmed). The first is for your primary entrance and the second can be used for a secondary entrance, where a longer delay is required to walk to the keypad to disarm the system. You can also arm the system with no entry delay at all by using the NO DELAY key when arming. This can provide greater security while on the premises or while away for extended periods of time. See ARMING THE SYSTEM section for procedure. See your installer for delay times programmed for your system. Exit Delay: Entry Delay 1: Entry Delay 2: 00-99 seconds 00-99 seconds 00-99 seconds

Disarming the System

Use the OFF key to disarm the system and to silence alarm and trouble sounds. See the SUMMARY OF AUDIBLE NOTIFICATION section for information, which will help you to distinguish between fire and burglary alarm sounds. IMPORTANT: If you return and the main burglary sounder is on, DO NOT enter the premises, but call the police from a nearby safe location. If you return after an alarm has occurred and the main sounder has shut itself off, the keypad will beep rapidly upon entering. This indicates that an alarm has occurred during your absence and an intruder may still be on the premises. LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location. To disarm the system and silence burglary alarms:

Your user code

The READY light will light (if no alarms have occurred while armed) and the keypad will beep once to confirm that the system is disarmed.

Memory of Alarm

If an alarm occurs, the keypad displays the zone number (s) that caused the alarm and the type of alarm (e.g., FIRE ALARM ). These messages remain displayed until cleared by a user. To clear the display, note the zone number displayed and enter an OFF sequence (enter your security code and press the OFF key). If the READY light is blinking, go to the displayed zone and correct the fault (close windows, etc.). If the fault cannot be corrected, notify your alarm company.
Bypassing Protection Zones

Using Powerline Carrier Device Commands (Lights On/Lights Off Keys)
Your system may be set up so that certain lights or other devices can be turned on or off by using the device command from the keypad. Ask your installer if this has been done in your system. If programmed for your system, some devices may activate automatically upon certain system conditions. In this case, the following commands can be used to override the device activation. See your installer for a full explanation of this feature.
To activate X-10 devices 1-6: FUNCTION + LIGHTS ON To deactivate X-10 devices 1-6:
+ dev. no. (2 beeps) + dev. no. (2 beeps)

+ LIGHTS ON

To activate X-10 devices 7 & 8**: Your user code To deactivate X-10 devices 7 & 8**: Your user code
+ FUNCTION + LIGHTS ON + dev. no. (2 beeps) + FUNCTION + LIGHTS ON + dev. no. (2 beeps)
** Devices 7 and 8 may be assigned to system devices, such as alarm bells, which should not be activated using this command because they are activated automatically under certain system conditions. See your installer and the table below.

Device Descriptions

Device
See your installer for device numbers assigned for your system.

Description

Message Recording/Playback/Volume Control

Recording a Message

Your system can record a brief message (up to 20 seconds) that can be played back later. To record a message: FUNCTION + RECORD The keypad beeps and displays REC MESSAGE. Begin speaking into the microphone. NOTE: The Record function can only be performed from the master keypad. It cannot be performed from any other wireless keypad (ex. 5827). To stop recording before the end of 20 seconds: Press OFF Otherwise, the recording automatically stops after 20 seconds. The keypad beeps twice, the REC display turns off, but the MESSAGE display remains on.

Message Playback

The lighted word MESSAGE indicates that a new message is in memory. After playing the message, the MESSAGE display turns off. See NOTE below if using a wireless keypad. To play back a message: FUNCTION + PLAY

Adjusting the Volume

The volume level of message playback, system announcements, and status beeps can be changed. You can also mute system announcements if desired. See NOTE below if using a wireless keypad. To adjust message playback/system announcemnt volume:

FUNCTION

+ VOLUME + [3] or [6]
[3] = increases volume one level, [6] = decreases volume one level (The keys beep at the selected volume when pressed.) Repeat the key sequence until the desired volume level is achieved. To mute system announcements: FUNCTION + VOLUME + OFF When muted, no system announcements will be made. Recorded messages will be announced, though, when PLAY is pressed. To restore announcement sounding: FUNCTION + VOLUME + [3] or [6] Volume level will be restored to the level that was selected prior to muting the sound. NOTE: If a wireless keypad (5827) has been installed and is programmed for quick arming, it cannot be used to activate message playback or adjust the volume. In this case, you must use the master keypad to perform these functions. 20

AUX FUNCTION

The AUX key may have been programmed to either perform a predefined function or to send a preset message to a pager (see PAGER FEATURE section for pager operation). Ask your installer which function has been assigned for your system.

PRE-DEFINED FUNCTION

PAGING FUNCTION
If programmed for the AUX function, you can use the AUX key to activate a string of up to 20 keystrokes that have been stored in the systems memory. Typical functions include: Seldom used but repeatable sequences Arming sequences that involve bypassing zones before arming Device activation sequences
Defining the AUX Function

1. 2. 3. Enter

Master Code
The system must be disarmed before defining a function. + FUNCTION + AUX (hold down until 4 beeps sound).
Press the desired command sequence, up to 20 keystrokes. Press the AUX key between each command in the sequence. Press the AUX key twice to end the definition.
For example, to bypass Zones 10 and 11 and arm AWAY with NO DELAY, enter the following string:
+ FUNCTION + AUX + [6] + [10] + [11] + AUX + AWAY + [0] + AUX + AUX Master User Code
Note that the AUX key is included in the 20 keystroke maximum.
Performing the AUX function
Press and hold down the AUX key (hold down at least 2 seconds until 4 beeps sound), then enter the defined function will begin.

User Code

Clock/Calendar
To set the time and date:

NOTES: 1. 2. 3. 4. 5.

Your system can display the current time (see your installer). The date is not displayed, but has an internal function. The system must be disarmed with no faults present. + FUNCTION + [63]
Master User Code or Installer Code The keypad beeps twice for invalid data entries (e.g., an hour greater than 12), and the entry will not be accepted. The keypad beeps once for valid entries. Clock-Setting mode automatically ends if no keys are pressed for one minute. Daylight savings time may have been programmed to automatically begin and end. It is not possible to enter real-time clock programming mode from a wireless keypad (i.e. Ademco 5827) It is not possible to enter real-time clock programming mode when either FC or CA appears on the display.
Hour % (The current hour will be displayed with the AM/PM indication.) Enter the 2-digit hour (i.e., 01-12). Press [*] to accept the entry and continue to the AM/PM selection. Press [#] to exit Clock-Setting mode (keypad beeps 4 times). AM/PM 4 (The current AM/PM setting will display A or P.) Enter 1 for PM or 0 for AM. Press [*] to accept the entry and continue to the minute selection. Press [#] to return to hour-setting prompt. Minute

(The current minute will display.)
Enter the 2-digit minute (i.e., 00-59). Press [*] to accept the entry and continue to the month selection. Press [#] to return to AM/PM setting. Month
(The current month will display.)
Enter the 2-digit month designation (i.e., 01-12). Press [*] to accept the entry and continue to the day selection. Press [#] to return to the minute setting. Day
(The current day of the month will display.)
Enter the 2-digit day of the month (i.e., 01-31). Press [*] to accept the entry and continue to the year setting. Press [#] to return to the month setting. Year
(The current year will display.)
Enter the last two digits of the year (i.e., 00-99). Press [*] to accept the entry and exit Clock-Setting mode (keypad beeps 4 times). Press [#] to return to the day setting. 22
Scheduling User Interface
Upon getting into the scheduling user interface by entering master or installer code + FUNCTION + 64 , the following entries will be sequentially prompted to the user. Note that all inputs are checked for validity upon entry and all invalid entries are rejected. Hitting a * will allow the entries to be accepted and advance to the next field. Hitting a # will reject the entry and back up one field. Hitting the # in the Schedule Number screen will exit the schedule programming.
NOTES: 1. During the schedule programming, if three minutes passes and no key was entered, the programming will be terminated and no values will be saved. Furthermore, if a zone is troubled while in schedule programming, the system will abort the programming mode and show the troubled zone, and any uncompleted program event will not be saved. It is not possible to enter the schedule programming mode from a wireless keypad (i.e. Ademco 5827) It is not possible to enter the schedule programming mode when either FC or CA is displayed on the display
Because the keypad display does not show prompt titles, you must refer to these instructions while programming the system. The prompts are indicated by a number/letter combination. The prompts for option #64 are as follows: n i : b : b : E : E d d n A d E A d b Schedule number-------------for selecting a schedule number (1-8) Event identifier--------------- for selecting a schedule action (0-5) Begin time (hrs, am/pm)---- for selecting a schedule begin time (hour, am/pm) entry (00-12) Begin time (min)------------- for selecting a schedule begin time (minute) entry (00-59) Begin day--------------------- for selecting a schedule begin day (01-17) End time (hrs, am/pm)------ for selecting a schedule end time (hour, am/pm) entry (00-12) End time (min)--------------- for selecting a schedule end time (minute) entry (00-59) End day------------------------ for selecting a schedule end day (01-17) Device number--------------- for selecting a X-10 device number (1-8)

NOTE: The keypad beeps twice for invalid data entries (e.g.: an hour greater than 12), and the entry will not be accepted. The keypad beeps once for valid entries and four times when a schedule event is programmed successfully. [x] = the value that was last stored in the memory.

Schedule number

[x] = schedule number 1 to 8 [*] = continue [#] = exit schedule programming mode

Event Identifier

[x] = event identifier 0 to 5 [*] = continue [#] = return to previous prompt

xx : b

Begin Time (hour)
[xx] = begin hour 00 to 12 [*] = continue [#] = return to previous prompt

Begin Time (am/pm)

[0] = begin time, am (A) [1] = begin time, pm (P) [*] = continue [#] = return to previous prompt
Enter the 1-digit schedule number to be programmed, then press [*] to accept and advance to the next programming field: Event Identifier. Press the [#] key in this entry will exit the schedule programming mode. The keypad will beep four times and exit. Schedule number 7 and 8 are always random events that are meant to work only with X-10 devices. Note: This feature should be implemented when the user is trying to give the impression that a premises is lived in. The events will occur at random times (0-59 minutes) within the defined hour. 0 = Empty - no event scheduled (or schedule temporarily disabled. Keypad will beep four times and return to Schedule Number with the schedule number advanced. 1 = X-10 Device - the user is required to enter data up to and include the Device Number screen. Selection #1 is a time driven event that requires a begin and end time. 2 = Latch Key Report - the user is required to enter data up to and include the End Day screen. Selection #2 is a window driven event that requires a begin/end time. 3 = Automatic Stay Arming - the user is required to enter data up to and include the Begin Day screen. Selection #3 is a time driven event that requires a begin time to send a report. 4 = Reminder Announcements - the user is required to enter data up to and include the Begin Day screen. This is a reminder announcement. 5 = Alarm Clock - the user is required to enter the field values up to and include the Begin Day screen. This is a an alarm clock. Note: See figure 1 for an explanation of each entry of the event identifier. The begin hour is a two-digit entry. To enter the hour 3, press 0 followed by 3. The begin hour 00 indicates this schedule does not have a begin time. Press 0 to select AM or 1 to select PM. Note: When programming schedule number 7 and 8, do not program turn on/off to occur within the same 1-hour period. This will prevent this random feature from causing a reversal of the on/off times.

NOTE: If a remote phone session is not granted by the system, for any of the reasons identified above, a modem tone will be generated before the end of the session. the remote phone access mode.
Using Remote Phone Control Feature
Dial the controlss phone number. If no answering machine is present, the control will pick up between 1 and 14 rings, depending on the number programmed by your installer and will periodically announce SYSTEM. During a remote phone control session PC will be displayed on the control. Enter: (within eight seconds) The system status will be announced. Enter phone control commands as described on the next page: If an answering machine is on the premises, you need to dial the premises and hang up on the first ring. Wait at least five (5) seconds (but no more than 22 seconds) and dial the premises phone number again. The control will pick up and periodically announce SYSTEM. 28

Enter:

Your user code (within eight seconds)
The system status will be announced. Remote Phone Control Commands To remotely disarm system:
To remotely arm in AWAY mode: To remotely arm in STAY mode:

+ [3] + [2] or [3] + [0]

To remotely arm in AWAY or STAY mode with no delay: To remotely activate X-10 devices 1-6: [#] + [4] + device no. To remotely activate X-10 devices 7 & 8:

+ [#] + [4] + device no.

To remotely deactivate X-10 devices 1-6: [#] + [7] + device no. To remotely deactivate X-10 devices 7 & 8:
+ [#] + [7] + device no. + [6] + zone no.
To remotely Bypass zones:
To remotely activate Forced Bypass:

+ [6] + [#]

To remotely check system status: [*] To end remote phone session: Hang Up or

NOTES:

(1) Check with your installer to see if the Forced Bypass mode has been enabled. (2) When bypassing zones, make sure a confirmation beep sounds for each zone that has been bypassed.

),5($/$506<67(0

(If Installed)
Your fire alarm system (if installed) is active 24 hours a day, providing continuous protection. In the event of an emergency, the installed smoke and heat detectors will automatically activate your security system, triggering a loud, intermittent sound from the keypad. An intermittent sound will also be produced by optional exterior sounders, and interlaced with the voice descriptor, sounding every 15 seconds. A FIRE message will appear at your keypad and remain on until you silence and clear the alarm display.

In Case of Fire

1. 2. 3. 4.
Should you become aware of a fire emergency before your detectors sense the problem, go to your nearest keypad and press the single panic key (or panic key pair) assigned as FIRE emergency (if programmed by the installer) and hold down for at least 2 seconds. The alarm will sound. Evacuate all occupants from the premises. If flames and/or smoke are present, leave the premises and notify your local Fire Department immediately. If no flames or smoke are apparent, investigate the cause of the alarm. The zone number of the zone(s) in an alarm condition will appear at the keypad.

Silencing a Fire Alarm

1. Silence the alarm by entering
+ OFF key. + OFF key again.
To clear the alarm display, enter 2.
If the keypad indicates a trouble condition after the second OFF sequence, check that smoke detectors are not responding to smoke- or heat-producing objects in their vicinity. Should this be the case, eliminate the source of heat or smoke. If this does not remedy the problem, there may still be smoke in the detector. Clear it by fanning the detector for about 30 seconds. When the problem has been corrected, clear the display by entering

+ OFF key.

National Fire Protection Associations Smoke Detector Recommendations
With regard to the number and placement of smoke and heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's (NFPA) Standard #74 noted below. Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household. The equipment should be installed as follows: A smoke detector installed outside of each separate sleeping area, in the immediate vicinity of the bedrooms and on each additional story of the family living unit, including basements and excluding crawl spaces and unfinished attics. In addition, the NFPA recommends that you install heat or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached garages.

KITCHEN DINING

BEDROOM BEDROOM

TV ROOM

KITCHEN

DINING

LIVING ROOM

BEDROOM

Smoke Detectors for Minimum Protection Smoke Detectors for Additional Protection BEDROOM Heat-Activated Detectors

BEDROOM KTCHN

TO BEDROOM

CLOSED DOOR

GARAGE

BASEMENT

01000-002-V0

Emergency Evacuation

Establish and regularly practice a plan of escape in the event of fire. The following steps are recommended by the National Fire Protection Association: 1. 2. Position your detector or your interior and/or exterior sounders so that they can be heard by all occupants. Determine two means of escape from each room. One path of escape should lead to the door that permits normal exit from the building. The other should be an alternative escape, such as a window, should your path to that door be unpassable. Station an escape ladder at such windows if there is a long drop to the ground. Sketch a floor plan of the building. Show windows, doors, stairs and rooftops that can be used to escape. Indicate escape routes for each room. Keep these routes free from obstruction and post copies of the escape routes in every room. Assure that all bedroom doors are shut while you are asleep. This will prevent deadly smoke from entering while you escape. Try the door. If the door is hot, check your alternate escape route. If the door is cool, open it cautiously. Be prepared to slam the door if smoke or heat rushes in. When smoke is present, crawl on the ground. Do not walk upright, since smoke rises and may overcome you. Clearer air is near the floor. Escape quickly; don't panic. Establish a place outdoors, away from your house, where everyone can meet and then take steps to contact the authorities and account for those missing. Choose someone to assure that nobody returns to the house many die going back.

01000-023-V0

OS ET OO DR BE M

M OO DR BE

M OO DR

2nd FLOOR

N HE TC KI

OO DR BE

BACK DOOR

M OO DR BE TH BA

1st FLOOR

6<67(0)81&7,216

For additional security, users other than you who do not need to know your code can be assigned different security codes. These secondary users are identified by "user numbers" when their codes are assigned. You can assign up to 6 user codes (2-digit user numbers 03-08). Note that the master (primary) user of the system is the only one who can assign codes to secondary users, and is designated user no. 02; user no. 01 is the installers code. All codes can be used interchangeably when performing system functions (a system armed with one user's code can be disarmed by another user's code), with the exception of the Babysitter Code described below. Babysitter Code (User 07): This code can be used to arm the system, but cannot disarm the system unless the system was armed with this code. This code is typically assigned to someone (such as a babysitter) who needs to arm/disarm the system only at certain times. The Babysitter Code is assigned to User 07. Duress Code (User 08): This feature is intended for use when you are forced to disarm or arm the system under threat. When used, the system will act normally, but can silently notify the alarm monitoring company of your situation, if that service has been provided. Duress Code is assigned to User 08. The Duress Code is useful only when the system is connected to an alarm monitoring company.
To Add/Delete a User or Change a User's Code
Changing the Master User Code Follow the procedure for changing a user's code, but enter User No. 02 and enter the new code twice. IMPORTANT: Temporary users of the system (e.g., babysitters, cleaning staff) should not be shown how to use any system function they do not need to know, such as bypassing protection zones for example.
Sequential key depressions for all steps in a procedure must be made within 2 seconds of one another, or else the entire entry is aborted and must be repeated from its beginning. Add a user code: Master User Code Delete a user code: Master User Code Wait (about 3 seconds) until the keypad beeps once before pressing any other key. The code is automatically deleted. + CODE Key + user number (03-08) + CODE Key + user number (03-08) + users code
Testing the System (to be conducted weekly)

Entering Test Mode

The TEST key puts your system into the Test mode, which allows each protection point to be checked for proper operation. The keypad sounds a single beep every 45 seconds as a reminder that the system is in the Test mode. NOTE: An alarm message will not be sent to your alarm monitoring company during the following tests. Disarm the system and close all protected windows, doors, etc. The READY message should be displayed and the green READY indicator (if present on the keypad) should also be lit. Enter the security code then press TEST WATCH. All LCD segments will light for 3 seconds. LISTEN. The external sounder should sound for 2 seconds and then turn off. If the sounder does not sound, notify your service company. FAULT ZONES. Open each protected door and window in turn and listen for three beeps from the keypad. Identification of each faulted protection point should appear on the display. The display will clear when the door or window is closed. Walk in front of any interior motion detectors (if used) and listen for three beeps. The identification of the detector should appear on the display when it is activated, and its voice descriptor will be announced (if programmed). The display will clear when no motion is detected. Note that if wireless motion detectors are used, there is a 3-minute delay between activations. This is to conserve battery life. To test all smoke detectors, follow the manufacturer's instructions. The identification of each detector should appear on the display when each is activated. If a problem is experienced with any protection point (no confirming sounds, no display), notify your service company. When all protection points have been checked and are intact (closed), there should be no zone identification numbers displayed on the keypad.

BURGLARY/AUDIBLE EMERGENCY ALARM a. SYSTEM DISARM b. SYSTEM ARMING ATTEMPT WITH AN OPEN ZONE. c. BYPASS VERIFY a. SYSTEM IS IN TEST MODE b. LOW BATTERY AT A TRANSMITTER c. SYSTEM LOW BATTERY d. FAIL TO COMMUNICATE ARM AWAY OR MAXIMUM a. ARM STAY OR INSTANT b. ZONE OPENED WHILE SYSTEM IS IN CHIME MODE. a. TROUBLE b. MEMORY OF ALARM a. ENTRY DELAY WARNING b. EXIT DELAY WARNING
alarm + zone voice descriptor
a. DISARMEDREADY TO ARM b. DISARMEDNOT READY TO ARM c. zones bypassed a. No announcement b. low battery + zone voice descriptor c. system low battery d. check system ARMED AWAY [INSTANT] EXIT NOW a. ARMED STAY [INSTANT] EXIT NOW b. zone voice descriptor a. fault + zone voice descriptor b. fire alarm or alarm + zone voice descriptor a. DISARM SYSTEM NOW b. ARMED [AWAY] [INSTANT] EXIT NOW
ONE SHORT BEEP (once every 45 secs) Speaker and external piezo TWO SHORT BEEPS Speaker and ext. piezo THREE SHORT BEEPS Speaker and external piezo RAPID BEEPING Speaker and external piezo SLOW BEEPING Speaker and external piezo
Additional Announcements:
Pressing STATUS key once will announce the following primary messages, depending on the systems status at the time: DisarmedReady to Arm [check system] Disarmed [not ready to arm] Armed [away] [stay] [instant] [check system] [exit now] Pressing the STATUS key twice will announce the following secondary messages, depending on the systems status at the time: Fire Alarm + zone voice descriptor Fault + zone voice descriptor Zones Bypassed Alarm + zone voice descriptor Low Battery + zone voice descriptor System Low Battery Fire Fault + zone voice descriptor Chime AC Loss NOTE: If there are no secondary messages, the primary status messages will be announced. ARMED LED: ON = System armed (Red) OFF = System disarmed Blinking = System armed, but a fault exists. READY LED: ON = System disarmed, ready to arm (Green) Blinking = System disarmed, not ready to arm (a fault exists). NOTE: When the system is armed, the READY LED turns off.
UL NOTICE: This is a " Grade A" residential system.
FCC ID: CFS8DLLYNX RADIO FREQUENCY EMISSIONS Federal Communications Commission (FCC) Part 15
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Phone:

WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example: Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. A user may not be able to reach a panic or emergency button quickly enough. While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death. Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90to 105 the detection performance can decrease. F, Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers. Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments.

ADEMCO LYNXR Series Security Systems
LYNXR/LYNXR24 and LYNXR-EN Installation and Setup Guide

RECORD

VOLUME

ESCAPE

LIGHTS ON

BYPASS

LIGHTS OFF STATUS

DELETE

FUNCTION

SELECT

NO DELAY

K5963V3bx 5/04 Rev. A

RECOMMENDATIONS FOR PROPER PROTECTION
The Following Recommendations for the Location of Fire and Burglary Detection Devices Help Provide Proper Coverage for the Protected Premises. Recommendations for Smoke and Heat Detectors With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's (NFPA) Standard #72 noted below.
Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows: For minimum protection a smoke detector should be installed outside of each separate sleeping area, and on each additional floor of a multi-floor family living unit, including basements. The installation of smoke detectors in kitchens, attics (finished or unfinished), or in garages is not normally recommended. For additional protection the NFPA recommends that you install heat or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached garages.
In addition, we recommend the following:
Install a smoke detector inside every bedroom where a smoker sleeps. Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway outside may not wake up the sleeper if the door is closed. Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air conditioners or humidifiers) are used. Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters) long. Install smoke detectors in any room where an alarm control is located, or in any room where alarm control connections to an AC source or phone lines are made. If detectors are not so located, a fire within the room could prevent the control from reporting a fire or an intrusion.
THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR TEMPORAL PULSE SOUNDING OF FIRE NOTIFICATION APPLIANCES.

KITCHEN DINING

BEDROOM BEDROOM

TV ROOM

KITCHEN

DINING

LIVING ROOM

BEDROOM

Smoke Detectors for Minimum Protection Smoke Detectors for Additional Protection BEDROOM Heat-Activated Detectors

BEDROOM KTCHN

TO BEDROOM

CLOSED DOOR

GARAGE

BASEMENT

01000-002-V0
Recommendations For Proper Intrusion Protection
For proper intrusion coverage, sensors should be located at every possible point of entry to a home or premises. This would include any skylights that may be present, and the upper windows in a multi-level building.
In addition, we recommend that radio backup be used in a security system. This will ensure that alarm signals can be
sent to the alarm monitoring station in the event that the telephone lines are out of order (alarm signals are normally sent over the phone lines, if connected to an alarm monitoring station).

2. Make Phone Line Connections - For local or full line seizure proceed to the appropriate steps below. Local Seizure a. Connect the incoming phone line to either the 8-position jack or terminals 2 (TIP) and 3 (RING) on the Lynx. b. Connect the handset phone lines to either the RJ11 jack or terminals 4 (TIP) and 5 (RING). Full Line Seizure: The control must be placed in series with the incoming phone line. Plugging the Direct Connect Cord directly into the RJ31X jack, allows the control to seize the phone line when an alarm occurs and normal phone line usage by the premises phones if the plug needs to be removed. a. Cut the incoming RING and TIP phone lines (typically red and green, respectively) and connect them to RJ31X terminals 4 (red) and 5 (green). b. Connect the premises end of the cut RING and TIP wires to RJ31X terminals 1 (grey) and 8 (brown) respectively. c. Wire the flying leads of a Direct Connect Cord to the controls phone terminals as shown in the diagram or plug into the 8-position jack. d. Plug the Direct Connect Cord into the RJ31X jack.

INCOMING PHONE LINE

RING TIP RED

TO PREMISES PHONES

RING TIP BROWN

DIRECT CONNECT CORD

GREEN BROWN GREY RED

8-POSITION JACK

HARDWIRED ZONE: If the EOLR is not at the end of the loop, the zone will not be properly supervised, and the system may not respond to an open circuit on the zone. 3. Make Hardwired Zone Connections - Zone 1 is an EOLR supervised zone that supports both open circuit and closed circuit devices and has a response time of 350msec. Maximum zone resistance: 300 ohms, plus EOLR a. b. c. 4. Connect sensors/contacts to the hardwired zone terminals 6 (+) and 7 (). Refer to the Summary of Connections diagram. Connect closed circuit devices in series in the high (+) side of the loop. The EOL resistor must be connected in series with the devices, following the last device. Connect open circuit devices in parallel across the loop. The 2000-ohm EOLR must be connected across the loop at the last device.

01000-008-V0

Full Line Seizure Connections
Note: The hardwire zone cannot be used as a fire zone.
Make External Sounder Connections - The control panel supports either a 6-14VDC piezo sounder (30mA max.) or 6-14VDC bell (120mA max.; e.g. ADEMCO WAVE2EX). a. Connect a piezo sounder to terminals 10 (+) and 11 (); OR a bell to terminals 11 () and 12 (+). LOCAL SOUNDER DISABLE: The Master Keypads built-in piezo sounder can be disabled by removing the shorting jumper (shunt) on the terminal board. If disabled, however, no sounding will occur upon AC loss, since the external sounder does not operate when AC power is lost.

Note: Keypad beeps if the zone is faulted when system is disarmed and Chime mode is on.

01000-020-V0

Type 09 Supervised Fire

Type 10 Interior w/Delay

Type 20 ArmStay

Type 21 ArmAway

Type 22 Disarm
Type 23 No Alarm Response Type 24 Silent Burglary

Data Field Descriptions

Defaults (where applicable) are Indicated in Text. The following pages list all data fields in this Control (in numerical order). Use the blank programming form to record the data for this installation. Note that both keypad LEDs flash while in Programming mode.
Note: Entering a number other than the one specified will give unpredictable results.

Installer Code

Enter 4 digits, 0-9
The Installer Code is used to enter the 4-digit Master Security Code. See "Master Code" in the System Operation section for procedure. If enabled, security code is not required to arm the system. The user simply presses and holds down the AWAY or STAY key to arm.

Quick Arm Enable

0 = do not allow quick arm 1 = allow quick arm

Keypad Backlight Timeout

0 = no timeout; always backlight keys 1 = turn backlighting off after inactivity
This option allows the choice of either always backlighting the keypad or turning the backlighting off after 10 seconds of keypad inactivity.

Forced Bypass

0 = no forced bypass 1 = provide automatic bypass of all open (faulted) zones
All zones bypassed by this function will be displayed after the bypass is initiated. Note: UL installations: must be 0 (no forced bypass) The House ID identifies receivers and wireless keypads. If a 5827 Wireless Keypad or 5804BD/5804BDV Transmitter is to be used, a House ID Code MUST be entered, and the keypad should be set to the same ID. Powerline Carrier Devices require a House ID. This field identifies this House ID to the Control. The Powerline Carrier Devices are programmed in field 80.

RF House ID Code

00 = disable all wireless keypad usage 01-31 = House ID
Powerline Carrier Device (X-10) House ID
0=A 1=B 2=C 3=D 4=E 5=F 6=G 7=H 8=I 9=J # + 10 = K # + 11 = L # + 12 = M # + 13 = N # + 14 = O # + 15 = P

Chime by Zone

0 = no (chimes on fault of any entry/exit or perimeter zone when Chime mode is activated 1 = yes (chimes on fault of those zones assigned to Zone List 3 when Chime mode on)

NOTES: Verify that the pager supports [*] and [#] characters before using them. Some pagers require an additional delay [pause] in order to receive the entire message.
If entered, these digits will appear in front of the 7-digit pager message sent by the control (either upon a system event or upon pressing the AUX key [if programmed for paging]), and during latch key report (if enabled during scheduling). These digits can consist of a PIN number, account number, pauses or special digits needed by the pager (these types of characters are not displayed), or any other characters the user chooses that will be displayed (eg., using a character code to distinguish between control panel messages and other pager messages). You do not need to fill all 16 digits. Press [] + next field number to exit the field. To clear the field, press 88. See field 87 to select the AUX key Paging feature. See field 49, which must have an option 6-9 selected to enable paging messages, for description of the pager message. If an Event Logging selection is made in field 90, a message can be sent to the central station receiver when the log is 80% full. If the log becomes full, a new message will overwrite the oldest message in the log. Note: All control and readout from the log, aside from the selection made by the installer in field 90, is accomplished via the downloader. Example: To select Alarm/Alarm Restore and Open/Close, enter 9 (1 + 8); to select all events, enter #15. Default 3 = alarm/alarm restore (1) plus trouble/trouble restore (2). The system has the ability to record various events in a history log (84event capacity). The types of events to be logged can be selected as indicated. At any time, the downloader operator can then upload the log and view or print out all or selected categories of the log. The log can also be cleared by the download operator. The display/printout at the central station will show the date, time, event, and description of the occurrences. Note: System messages are logged when any non-zero selection is made.
Event Log 80% Full Report Code

Event Logging Options

0 = No event logging 1 = log Alarm/Alarm Restore 2 = log Trouble/Trouble Restore 4 = log Bypass/Bypass Restore 8 = log Open/Close x = log combination of events (add value of entries)
The features programmed in Field 91 differ between LYNXR models. Ensure you use the correct option for the model you are installing! LYNXR/LYNXR24 Long Range Radio/Alarm Audio Verification (AAV) Trigger/Remote Phone Control
0 = long range radio trigger only 1 = AAV and remote phone control 2 = long range radio trigger and remote phone control 4 = AAV only
Notes: For UL installations Alarm Audio Verification cannot be used. Alarm Audio Verification will only function when Contact ID is selected. For LYNXR/LYNXR24, this option is used to enable the Long Range Radio, Alarm Audio Verification and/or Remote Phone Control options. If Long Range Radio (0) is selected, trigger output (terminal screw #8) will generate a steady signal for burglary alarm (a single 3 to 4-second pulse for all types of silent alarms) or a temporal signal for fire alarm. (Refer to Long Range Radio Installation Instructions for appropriate wiring.) Alarm Audio Verification requires the installation of the LYNX-AVM. (Refer to LYNX-AVM Installation Instructions) Notes: (1) If Long Range Radio is being connected, Alarm Audio Verification cannot be used. (2) In order to activate the remote phone control feature and defeat an answering machine, ensure that the correct ring detection count (15) has been programmed in field 95. (3) Remote phone session will be terminated if a report must be sent. (4) A Long Range Radio cannot be connected f AAV is selected. (5) Alarm Audio Verification will only function when Contact ID is selected and cannot be used for UL installations. (6) If an alarm will be reported to primary and secondary phone numbers, AAV can only function via the secondary number. (7) If an alarm will be reported to a pager (6-8 in field 49), or to follow me phone number (10-12 in field 49) AAV cannot be used. For LYNXR-EN, this option is used to enable the Audio Alarm Verification and/or the Remote Phone Control features. Notes: (1) In order to activate the Remote Phone Control feature and defeat an answering machine, ensure that the correct ring detection count (15) has been programmed in field 95. (2) Remote phone session will be terminated if a report must be sent. (3) Alarm Audio Verification will only function when Contact ID is selected. AAV cannot be used for UL installations. (4) If an alarm will be reported to primary and secondary phone numbers, AAV can only function via the secondary number. (5) If an alarm will be reported to a pager (6-8 in field 49), or to follow me phone number (10-12 in field 49) AAV cannot be used.

LYNXR-EN Alarm Audio Verification (AAV)/Remote Phone Control
0 = none 1 = AAV and remote phone control 2 = remote phone control only 4 = AAV only
Notes: (1) For UL installations alarm audio verification cannot be used. Alarm Audio Verification will only function when Contact ID is selected. (2) AAV and Remote Phone Control features can only be used if the central station or remote phone supports DTMF commands. (3) No programming is required if connecting an ALARMNET 7845C device because the option is always enabled.
Number of Reports In Armed Period
0 = reports limited to a total of = unlimited number of reports
This option can be used to limit the number of messages (alarm & alarm restore reports) sent to the central station in an armed period. UL installations: must be 1 (unlimited reports) If enabled, the control will ignore the last 1, 2, or 3 digits of the programmed callback number (field 94) during a single download session. This allows the download operator to temporarily change the callback phone number by the number of digits selected, which allows the control to call back similar, but different numbers during a single session. For example, if downloading to a large number of controls, the operator can command the controls to call back phone numbers 5551111, 555-1112, 555-1113, etc., thus spreading the communications among several computers.

Flexible Callback

0 = no flexible callback 1 = last digit flexible 2 = last 2 digits flexible 3 = last 3 digits flexible
DOWNLOAD INFORMATION (94, 95)
Download Call Back Phone Number
Enter up to 20 digits as follows: 09, # +11 for *, # + 12 for #, # + 13 for a pause.
This is the phone number the control will use to call back the downloading computer. Do not fill unused spaces. End field by pressing. To clear entries from field, press 94.
Ring Detection Count For Downloading/ Remote Phone Control
0 = disable station initiated download and remote phone 1-14 = number of rings before control picks up phone line 15 = defeat answering machine
Enter 15 to select defeat answering machine mode. If an answering machine is on the premises, you need to dial the premises and hang up on the first ring. Wait at least five (5) seconds (but no more than 22 seconds) and dial the premises phone number again. The control will pick up and announce SYSTEM ENTER CODE every three seconds.

Enable trouble reports

[] = continue [#] = return to previous prompt 0 = disable 1 = enable
Response to phone line tamper
[] = continue [#] = return to previous prompt 0 = enable trouble sounder 1 = enable alarm sounder
Select the Lynx response to detection of a line cut at the 5842 Wireless Dialer. If the trouble sounder is enabled the system will sound a trouble event any time the 5842 phone line is cut. If the alarm sounder is enabled the system will a trouble by day or an alarm at night in the event that the 5842 phone line is cut. Enter [1] to select alarm or [0] to select trouble in the event of a 5842 line cut. Press [] to advance to next field or [#} to return to the previous prompt.
Note: If an X-10 device has been programmed to ZT05 or ZT07 and *55 has been enabled, the device response will be dependent upon the selection made in *55 Field "Ln".

Enable back-up reporting

Allows Lynx to do back-up reporting for the 5842 wireless dialer. Enter [1] to enable back-up reporting. Refer to the 5842 Wireless Dialer Installation guide for additional information. Enter [0] to disable back-up reporting. Enter [#} to return to the previous prompt. Note: Lynx must be connected to the premises phone line via the 5842 Wireless Dialer.
56 Enhanced Zone Programming Mode
This is an interactive menu mode that is used to program zone numbers, zone types, alarm and report codes, and to identify the type of loop input device. This mode can also be used for entering 5800 Series transmitter serial numbers.
Note: There are two methods for entering transmitter serial numbers. The first method is by using 56 Enhanced Zone Programming mode (described below). The second method is by using 83 Enhanced Sequential Mode. Note that the 83 Enhanced Sequential Mode requires that all zone information first be entered using 56 Enhanced Zone Programming mode.
You must refer to these instructions or to the Program Form while programming the system because the keypad display does not show prompt titles. Instead, prompts are indicated by a number/letter combination. The prompts for 56 are as follows: A 01 b C d E F 1A 1b 1C 1d 1E 1F Zone Number ----------------------- for entering the zone number Zone Type---------------------------- for entering zone type Report Code ------------------------- for entering the zones report code Input Type--------------------------- for entering the transmitters input type Loop Number ----------------------- for entering the transmitter loop number Delete Serial Number? ---------- for deleting existing serial number Enroll Mode?------------------------ selects serial number enroll mode Serial Number --------------------- for entering transmitters serial number Voice Descriptor? ------------------ selects voice descriptor mode Descriptor 1 ------------------------- for entering first descriptor word Descriptor 2 ------------------------- for entering second descriptor word Descriptor 3 ------------------------- for entering third descriptor word

Report code

Enter the report code for this zone. [] = continue [#] = return to previous prompt

Input type

3 =RF (supervised RF) sends periodic check-in signals, faults, restore and low battery signals
Note: RF type transmitters must remain within range of the receiver, otherwise a supervision failure signal will occur.
4 = UR (unsupervised RF) sends same as RF type, but control does not supervise the check-in signals 5 = BR (button type) sends only fault and low battery signals; does not send restores or check-in signals
Note UR and BR type transmitters may be carried off premises (out of range without causing a supervision failure.
[] = continue [#] = return to previous prompt
Loop number or Loop and Serial number (if using RF Learning)
1-4 = loop number for the zone of the transmitter being entered. 0 + [] = continue to DELETE ZONE PARAMETERS CONFIRMATION prompt (F) [] = continue to the ENROLL MODE prompt (1A) if not entered, or VOICE DESCRIPTOR prompt if already entered [#] = return to previous prompt
This prompt can be used to enroll loop number and serial number via RF transmission or the loop number can be enrolled manually. If using the RF Learning Mode, there is no need to manually enter a loop number. Proceed directly to RF Learning Notes: (1) BR type devices cannot be enrolled by using UR or RF type. Likewise, UR or RF type devices cannot be enrolled by using a BR type device. There is a 52-second time-out for RF enrolling. At the end of the time-out, the system returns to the INPUT TYPE prompt (d). If enrolled, loop number and L are displayed. (2) Once encrypted (high-security) devices have been enrolled they must be activated. Refer to the devices Installation Instructions to activate the High-Security Mode.
RF Learning - Two (2) transmissions (2 key depressions) at least 5 seconds apart will be required for BR type devices (device type 5). Two beeps will sound after the second transmission, confirming that the loop number and serial number have been learned. For all other device types, four (4) transmissions are required (fault, restore and fault, restore). A single beep will sound after the second transmission confirming that the loop and serial number have been captured. Following the fourth transmission the system will confirm that the loop number and serial number have been learned and announce the Voice Descriptor for the zone, if it is programmed, followed by two beeps. Press [] to continue. Manual Entry - Enter the desired loop number and press [] to continue (see the transmitters Installation Instructions for specific loop designations). Note: The loop number can be changed even if the zone has already been entered. Care should be taken when using this feature as it has the capability to make zones inoperable by creating a mismatch of a working serial number/loop number combination. This should be re-confirmed if the loop number is changed. L indicates that the zones serial number has already been enrolled.

Start event type

0 = Not used 1 = Alarm 2 = Fault 3 = Trouble [] = continue [#] = return to previous prompt

Start zone list

1-3 = zone list number (to be programmed in field 81) 0 = zone list not used for this device [] = continue [#] = return to previous prompt
If a zone list will be used to start the device action, enter the zone list number at this prompt.

Start zone type

01-58 = zone type to start this device action (select only those that are applicable) 00 = zone type not used for this device [] = continue [#] = return to previous prompt
If a zone type or system operation will be used to start the device action, enter the appropriate 2-digit code for the device being programmed (see table that follows). Choices for zone types
00 = Not Used 01 = Entry/Exit #= Entry/Exit #= Perimeter 04 = Interior Follower 05 = Trouble Day/Alarm Night 06 = 24 Hr Silent 07 = 24 Hr Audible 08 = 24 Hr Aux 09 = Fire 10 = Interior w/Delay 24 = Silent Burglary 42 = Sys. Batt. Low 43 = Comm. Failure 52 = Kissoff 58 = Duress
Choices for system operation
20 = ArmingStay 33 = Any Alarm (except zt 08) 21 = ArmingAway 36 = At Bell Timeout** 22 = Disarm. (Code + OFF) 38 = Chime 31 = End of Exit Time 39 = Any Fire Alarm 32 = Start of Entry Time 40 = Bypassing ** Or at Disarming (which ever occurs earlier)

Stop zone list

1-3 = zone list to stop this device action 0 = zone list not used [] = continue [#] = return to previous prompt
If a zone list will be used to STOP, or restore, the device action, enter the zone list number 1, 2, or 3 (to be programmed in 81 mode). If not used, enter 0.

Stop zone type

If a zone type or system operation will be used to STOP the device action, enter the appropriate 2-digit code (see the "ZT" choices listed above). If not, enter 00. The display then returns to the DEVICE NUMBER prompt (A) so that you can enter the next device number to be programmed, or enter [0][0] to end device programming.

81 Zone List Menu Mode

While in Program mode, press 81 to enter Zone List Menu Mode. This mode is used to program zone lists for output devices (programmed in 80 menu mode) or Chime-by-Zone in Zone List 3. NOTES: Any list may include any or all of the systems zone numbers. A zone list can be assigned to more than one Powerline Carrier Device. The prompts for *81 are as follows: 81 A 01 b C d E Zone List Programming ------------------- Main Menu prompt Zone List Number --------------------------- for entering the zone list number to be programmed Zone Entry to List --------------------------- for entering zones to the assigned zone list Delete Entire List? -------------------------- for deleting the entire zone list and its contents Delete Specific Zones From List? ------- Selects whether to delete zones or return to next zone list number Delete Zones----------------------------------- for deleting specific zones from the current zone list

Notes: (1) (2) Entering a number other than one specified will give unpredictable results. Do not assign zones with zone types 20, 21 or 22 to a zone list. Zone list programming

8I A b 0I

Pressing 1 advances to the next prompt below. Pressing 0 exits mode, upon which this prompt blinks, indicating the mode is inactive. Enter the Zone List Number 01, 02, or 03 to program (or 00 if no zone lists are used).

Zone list number

01-03 = zone list number to be programmed 00 = exit Zone List mode [] = continue

Zone entry to list

01-41, 95, 96, 99 = zone numbers to add to zone list [] = accept zone number and enter the next zone number 00 = accept zone number(s) and continue to next prompt
Enter each zone number to add to the zone list by first entering the zone number, then the [] key (for example, 03). The system will announce the Voice Descriptor for the selected zone, if it is programmed. After all desired zones are enrolled, enter 00 to advance.

Delete entire zone list?

0 = dont delete; continue to next prompt 1 = delete the current zone list
To delete the zone list, enter 1. All zones in the zone list will be deleted automatically and programming will return to the ZONE LIST NUMBER prompt. To save the zone list or delete specific zones from the list, enter 0. To save the entire zone list, enter 0 and programming will return to the ZONE LIST NUMBER prompt. To delete a zone or zones in a zone list enter 1.

Delete zones from list?

1 = continue to delete zones prompt 0 = dont delete; continue to next zone list number prompt (A.01) [#] = return to zone list number prompt (A.01)

Delete zones

Enter each 2-digit zone number to be deleted from the current zone list, followed by the [] key. [] = delete zone and enter next zone to be deleted 00 = delete zone and return to next zone list number prompt (A.01) desired
When deleting a zone(s) from the zone list, if the selected zone has a Voice Descriptor programmed, upon deletion it will be announced as a confirmation that it has been deleted. After all zones to be deleted are entered, enter 00 to return to the ZONE LIST NUMBER prompt so that another list can be programmed, if desired.
83 Enhanced Sequential Mode
By using this mode, you can add, delete, or change the serial number of a transmitter in a zone, but retain all other existing data that has been programmed for that zone. Note that the 83 Enhanced Sequential mode requires that all zone information must first be entered using the 56 Enhanced Zone Programming mode for all zones below zone number 26 (4 button key area). Note: Any zone which already has a serial number learned in will not be accessible in 83 Enhanced Sequential mode! Certain button-type transmitters have more than one button (e.g., 5804). Note that each button must be assigned to a different zone. Similarly, the 5816 Transmitter has contact terminals and a reed switch for use with a magnet. If using both, each must also be assigned to a different zone. This means that the procedures that follow must be repeated for each button-type zone below zone number 26 or contact on the transmitter. Four zone button-type devices are held in zones 26 and above. They will be started on boundaries of zones 26, 30, 34, and 38. These four zone button-type devices will have the option to have all information entered in this field. One entry will set the loop number, report code, zone type, and input device type for all 4 buttons, and a second entry will enter one serial number into four zones. Note: Use this mode only after all other zone information has been programmed, including transmitter loop numbers except for button-type zones over zone number 26. The panel will stop at zones 26, 30, 34 and 38 and zone data can be entered as a default here. Enter Serial Number Sequential mode by pressing 83. The prompts for 83 are as follows: A 01 1A 1b F Zone Number ------------------------------------ for entering the zone number to be programmed Enroll Mode -------------------------------------- Selects method of serial number or viewing Enroll Serial Number ------------------------- for entering transmitter serial numbers Delete Serial Number------------------------- for deleting existing serial numbers

00 second pause A ALARM ATTIC B BABY BACK BASEMENT BATHROOM BEDROOM C CHECK D DELAY DOOR DEN DETECTOR DINING DINING ROOM DOOR DOWNSTAIRS DRIVEWAY E EAST EIGHT EMERGENCY F FAMILY ROOM FIRE FIRE DETECTION FIRST FLOOR FIVE FLOOR FOUR FRONT G 48 GARAGE 49 GUEST ROOM 09 GUN H HALL I INSIDE K KITCHEN L LAUNDRY LAUNDRY ROOM LIBRARY LIVING LIVING ROOM P 61 PATIO 62 POLICE 18 POOL R 63 REAR 19 ROOM S SECOND FLOOR SEVEN SHED SHOP SIDE SILENT POLICE SIX SLIDING SMOKE SOUTH STORAGE SYSTEM T THIRD FLOOR THREE TRANSMITTER TWO 99 Z ZERO ZONES 1ST 2ND 3RD Custom Word #1 Custom Word #2 Custom Word #3 Custom Word #4 Custom Word #5 Blank (for erasing a previously programmed word) SYSTEM WORDS AC LOSS ARMED AWAY BYPASSED CHIME DISARMED DISARM SYSTEM NOW EXIT NOW FAULT INSTANT LOW BATTERY NOT READY TO ARM STAY
M 14 MAIN 15 MASTER 54 MASTER BEDROOM 55 MEDICAL 84 MESSAGE 56 MOTION DETECTOR N 57 NINE 16 NORTH 58 NURSERY O 59 OFFICE 60 ONE 17 OUTSIDE
U 78 UPSTAIRS 26 UTILITY 79 UTILITY ROOM W 27 WEST 80 WINDOW Y 28 YARD
Note: If button type device is used to Arm Away, Arm Stay, and disarm the system it is recommended to assign Check and Zones voice descriptors to each of the three zones. This will allow the system to announce Check Zones Low Battery if the button device has a low battery.
85 Record Custom Voice Descriptors
Use this mode to record up to 5 custom voice descriptors. Press 85 while in Programming mode.
Note: Entering a number other than one specified will give unpredictable results. Assign custom voice descriptors
Entering 1 advances to the next prompt below. Entering 0 exits mode, upon which this prompt blinks, indicating the mode is inactive. Record up to 5 custom words.

85 A 7d

Custom descriptor number
Enter 7 + d + [] Where d = 0-4, each representing custom word 70, 71, 72, 73, or 74, respectively. Any existing word will be announced. Press [#] to start recorder. Begin speaking immediately after the third beep. Speak the desired word clearly near the microphone. Recording stops after 1.5 seconds. 6 = accept word and ready to record next descriptor prompt (A.7d) [#] = re-record descriptor 00 = exit Record mode after pressing 6 to accept word Press any key to repeat the recorded word.

Voice Prompt Programming

The LYNXR Series features a quick programming mode that allows you to program the system by responding to a series of voice prompts. The Voice Prompt Programming Guide provides you with the information required to use this feature. Voice Prompt Programming Keypad Functions: The keys shown below are used to navigate through the Voice Prompt Programming Feature.

Remote Programming Information
LYNX must be connected to the telephone line if using Remote Programming.
The downloading system can perform many functions when in communication with the Control. Besides uploading and downloading, the status of the system can be observed and various commands can be initiated, as follows: Arm the system in the away mode; disarm the system. Bypass a zone. Force the system to accept a new program download. Shut down communication (dialer) functions (for nonpayment of monitoring fees in an owned system). Shut down all security system functions (for nonpayment for a leased system). Inhibit local keypad programming (prevents account takeover).
Command the system to upload a copy of its resident program to the office. Set the time View/Modify X-10/ Scheduling Read: arming status, AC power status, lists of faulted zones, bypassed zones, zones currently in alarm, zones currently in trouble, and RF sensors with low battery conditions; read controls time.
Notes: (1) After the control and the PC have established valid communication, the keypad will become inactive and will display CC. (2) The keypad will become active after the download communication is terminated. (3) The detailed operation of the download functions is covered in the installation instructions for the Compass Downloader for Windows.
Remote Programming Advisory Notes
Keypad entries are ignored during the time interval stated above. A copy of the program downloaded may be printed using the IBM PC-compatible computers internal report generator, when an optional printer is connected (consult your PC manual for proper printer and connections). Program upload or download time is approximately one minute, fifteen seconds for a complete program.

System Operation

Security Codes
Installer Code The installer programs the 4-digit Installer Code initially as part of the programming procedure. The factory default Installer Code is 4-1-1-2, but may be changed in field 20. The Installer Code is the only code that can enter Programming mode and also, in normal operation mode, is used to enter the Master Code, which allows access to the normal functions of the system. Master Code In normal operation mode, the Installer Code is used to enter the 4-digit Master Security Code. To enter/change the Master code by installer, using the keypad enter: Installer Code + [CODE key] + [02] + desired 4-digit Master Code To change the Master code by master, using the keypad enter: Current Master Code + [CODE key] + [02] + new Master Code + new Master Code again Secondary User Codes In normal operation mode, the Master Security Code can be used to assign up to 6 secondary 4-digit security codes, including a Babysitter Code and a Duress Code. The Master Code can also be used to remove secondary codes from the system (individually). To assign (or change) a secondary security code, using the keypad enter: Master Code + [CODE key] + User # (0308) + desired Secondary Code The system will emit a single beep when each secondary code has been successfully entered. To delete a secondary security code, using the keypad enter: Master Code + [CODE key] + User # (0308) Security Code Notes

REMEDY

Check or change transmitter's battery. 1b. Check code switches inside transmitter. Must match with RF House Code programmed.
1c. Transmitter is located too far from RF receiver. 1c. Move transmitter or RF receiver. 1d. There is metal shielding between transmitter and RF receiver. 1e. Transmitter is malfunctioning. 1f. 2. Transmitter zone number appears during Transmitter Sniffer mode, but does not clear. Low battery message on keypad. 3a. Replace system battery. 3b. Replace battery in the RF keypad. 3c. Replace the battery in the displayed transmitter. 4a. Enter Code + OFF to exit Test mode. 4b. Enter Code + OFF and replace the battery. 4c. Check the transmitter indicated. Restore communication to the receiver to cancel the condition. 4d. Replace system battery Transmitter No. (zone) is not programmed. 1d. Check for large metal obstructions, then relocate transmitter if necessary. 1e. Verify by activating control with another, similar transmitter. If O.K. now, return defective transmitter. 1f. Verify programming. 2a. Set ZT to a valid active zone type in field 56. 2b. Install proper battery. 2c. "Enter" unit in field 56 or 83.
2a. Transmitter zone type (ZT) is set to 00 (Not Used). 2b. Transmitter battery not installed. 2c. 5800 System transmitter not "entered" in system.
3a. "Low Bat" (no zone Nos.) 3a. System battery is low or missing. 3b. "Low Bat" + "00". 3b. Remote RF keypad/button battery is low. 3c. "Low Bat" + "nn". 3c. Transmitter for zone nn has a low battery. 4. Periodic beep(s) from keypad. 4a. System is in Test mode. 4b. A transmitter low battery has occurred and is displayed. 4c. A supervision fault has occurred. 4d. System low battery 5. With 5800 System, there is no response to a transmitter in normal operation, although zone number clears during Transmitter Sniffer mode. Put control in Test mode. If zone does not respond, try operating the tamper switch or another input to the transmitter. 5a. If another input causes the zone to be displayed, the wrong input was "entered" when programming. 5b. If no response at all from this transmitter, this physical transmitter has not been entered by the system. Transmitter Sniffer display is being cleared by another unit programmed for this zone. 6a. Sensors not properly installed, wired, or monitored. 6b. Universal transmitter (5817) programmed wrong. 7. Intrusion alarm for no apparent reason. 7a. Protected door or window opened while system armed. 7b. Improper user operation of exit/entry delays. 7c. Magnets located too far from switches, and/or doors and windows not properly aligned.

( ) ( ) ( ) (+) (+) DATA SYNC OUT IN TIP RING TIP RING (+) HARD WIRED ZONE
WARNING: TO PREVENT RISK OF SHOCK DISCONNECT TELEPHONE LINE AT TELECOM JACK BEFORE SERVICING THIS UNIT. RJPOSITION JACK TO HANDSET PHONE LINE INCOMING PHONE LINE
LOCAL SOUNDER DISABLE SHUNT REMOVE TO DISABLE
ALL OUTPUT CIRCUITS ARE POWER LIMITED.
NOTE: Connection of the fire alarm signal to a fire alarm headquarters or a central station shall be permitted with the approval of the local authority having jurisdiction. The burglar alarm signal shall not be connected to a police emergency number.
The System must be checked by a qualified technician once every three years.
INCOMING TELEPHONE LINE EARTH GROUND PREMISES TELEPHONE 2k OHMS EOLR PIEZO BELL 6-14VDC 30mA max. 6-14VDC 120mA max. (e.g. WAVE2EX) NOTE USE ONLY 1332/1332X10 OR 1332CN TRANSFORMERS PROVIDED TO 24HR 110VAC UNSWITCHED OUTLET AC AC SYNC COM DATA WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM FCC ID: CFS8 DLLYNX (LYNXR/LYNXR24) AND CFS8DLLYNXREN-1 (LYNXR-EN) COMPLIES WITH FCC RULES, PART 68 FCC REGISTRATION No. 5GBUSA-25623-AL-E RINGER EQUIVALENCE: 0.6B PLUG-IN TRANSFORMER 9VAC, 15VA
THIS EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION'S STANDARD 72, CHAPTER 2 (NATIONAL FIRE PROTECTION ASSOC., BATTERYMARCH PARK, QUINICY, MA 02269). PRINTED INFORMATION DESCRIBING PROPER INSTALLATION, EVACUATION PLANNING AND REPAIR SERVICE IS TO BE PROVIDED WITH THIS EQUIPMENT.
1332/1332X10/1332CN CONNECTIONS
LYNXR SERIES SUMMARY OF CONNECTION

01009-016-V0

165 Eileen Way, Syosset, New York 11791

K5963V3o

Copyright 2004 Honeywell International Inc. www.honeywell.com/security