13. 14.

ARMED READY

OFF AWAY STAY

BYPASS

INSTANT

LOCATION OF DEDICATED PANIC KEYS. KEY D USED AS SPEED KEY (if programmed)
IMPORTANT!: When using the keypad to enter codes and commands, sequential key depressions must be made within 3 seconds of one another. If 3 seconds elapses without a key depression, the entry is aborted and must be repeated from its beginning.

ENTRY/EXIT DELAYS

General Information Your system has preset time delays, known as exit delay and entry delay. Whenever you arm your system, exit delay gives you time to leave through the designated exit door without setting off an alarm. Exit delay begins immediately after entering any arming command, and applies to all modes of arming protection. If programmed, a slow beeping will sound throughout the exit delay period. Entry Delay gives you time to disarm the system when you reenter through the designated entrance door. But the system must be disarmed before the entry delay period ends, or an alarm will occur. The keypad will beep during the entry delay period, reminding you to disarm the system. You can also arm the system with no entry delay at all by using either INSTANT or MAXIMUM arming modes. These modes provide greater security while on the premises or while away for extended periods of time. See your installer for your delay times.
SECURITY CODES & AUTHORITY LEVELS
General Information At the time of installation, you were assigned an authority level and a personal four-digit security code, known only to you and yours. The security code must be entered when arming and disarming the system. The authority level defines the system functions that you can perform. As an additional safety feature, other users that do not have a need to know your code can be assigned different security codes, and each user can be given a different authority level. Users are identified by "user numbers", which are assigned when assigning a user's security code. All codes can be used interchangeably when performing system functions within the limits of each code's authority level (a system armed with one user's code can be disarmed by another user's code), with the exception of the Operator Level C code. See AUTHORITY LEVELS section on the following page for detailed information regarding user authority levels. This feature is intended for use when you are forced to disarm or arm the system under threat. When used, the system will act normally, but can silently notify the central station of your situation, if that service has been provided. The duress code is pre-assigned by the installer during installation (auth. level 6). Important: This code is useful only when the system is connected to a central station. Note that if "Quick Arming" was programmed by the installer, the # key can be pressed in place of the security code when arming the system. The security code must always be used to disarm the system, however.

GLOBAL ARM ? 0 = NO , 1 = YES
PART.2 - SHOP? 0 = NO , 1 = YES
PART. 1 T WHSE USER 003 AUTH=3G.

To Change a User's Code

1. Enter Master or Manager code and press the number to be changed. 2. Enter the new code for that user.
ADD NEW USER? 0 = NO , 1 = YES

8 key + user

The system will recognize that the user number is already in use and will prompt whether or not this is a new user. Enter 0 to change the existing user's code to the code entered in step 3. The system will confirm that the change is allowed based on authorization level, and if so, will put the new code into effect. Note that if changing ones own code, the system will prompt for the new code to be reentered. This prevents accidentally changing one's own code.
USER 002 CHANGED SUCCESSFULLY

To Delete a User

1. Enter Master or Manager code and press the Number to be deleted. 2. Enter Master or Manager code first entered.
OK TO DELETE 0 = NO , 1 = YES

8 key + User

The system will recognize that the User number is already in use and will prompt to confirm that it should be deleted. Press 0 (NO) or 1 (YES). If yes, that user's code will be removed from all partitions to which it was assigned, and all authorization levels and other information about that user will be deleted. Note that a user can only be deleted from the partition in which it was first assigned, and can only be deleted by a user with a higher authority level. A User's security code cannot be deleted by oneself.

USER CODE DELETED

ACCESSING OTHER PARTITIONS
(GOTO Command and Global Arming)
To Access Another Partition
Each keypad is assigned a default partition for display purposes, and will show only that partition's information. But, if the user is authorized, a keypad in one partition can be used to perform system functions in other partitions by using the G O T O command. Note that only those partitions authorized and programmed by the installer can be accessed in this manner. To GOTO another partition: READY 1. Enter your security code, then press D + partition number (0-9). Entering partition number 0 will return the keypad to its original partition. 2.

LOG-ON TO AAAA PART. X COMPLETE The keypad will remain in the new partition until directed to go to another partition, or until 2 minutes has elapsed with no keypad activity. AAAA = alpha descriptor programmed by the installer X = partition number

Global Arming

The Global Arming option may have been programmed for use by some users. If Global Arming was enabled for use with your security code, a keypad prompt (message) will appear after pressing one of the arming function keys (STAY, INSTANT, AWAY, MAXIMUM, OFF). Follow the keypad prompts to continue arming the system. See your installer for detailed instructions on the use of this feature. If global arming does not apply to your security code, use the procedures described in the following pages. A "Master" keypad is one that reflects the status of the entire system (Partitions 1-8) on its display. This is useful because it eliminates the need for a security officer in a building to have to "log-on" to various partitions from one partition's keypad to find out where an alarm has occurred. A description of a typical display follows:
SYSTEM 12345678 STATUS RRNNA GB

Master Keypad Operation

ACCESSING OTHER PARTITIONS (cont'd)
Master Keypad Operation (continued) The status of each partition is directly below the partition number on the display. Possible status indications include: A = Armed Away M = Armed Maximum S = Armed Stay I = Armed Instant R = Ready N = Not Ready B = Bypassed/Ready T = Alarm Memory/Trouble present To obtain more information regarding a particular partition, enter G + [Partition No.] (i.e., G4). This will allow viewing only of that partition. In order to affect that partition, the user must log on with a code that has access to that partition. Also, in order for a user of any partition to log onto the "Master" partition (Partition 9) to view the status of all partitions, that user must have access to all partitions. Otherwise, access will be denied. The following is an example of what would be displayed for a fault condition on Zone 2 (Loading Dock Window) on Partition 1 (Warehouse) when logging on from a keypad on Partition 9:
WHSE DISARMED HIT G FOR FAULTS
This is the normal display that appears at Partition 1's keypad(s). Pressing G will display:
FAULT 02 LOADING D O C K W I NDOW

Additional zone faults will be displayed one at a time. To display a new partition's status, press G + [Partition No.]. This will display the status of the new partition. The "Armed" LED on a Master keypad will be lit only if all partitions have been armed successfully. The "Ready" LED will be lit only if all partitions are "ready to arm." The sounder on a Master keypad will reflect the sound of the most critical condition on all of the partitions. The priority of the sounds is as follows: A. Pulsing fire alarm sounds B. Steady burglar alarm sounds C. Trouble sounds The sounder may be silenced by pressing any key on the Master keypad.
Common Lobby Operation When an installation consists of a partition shared by users of other partitions in a building, that shared partition may be assigned as the "common lobby" partition for the system. An example of this might be in a medical building where there are two doctor's offices and a common entrance area. This option employs logic for automatic arming and disarming of the common lobby. Partitions may be set to affect and/or attempt to arm the common lobby. This will affect the way the lobby will react when arming or disarming activity occurs in another partition. Partitions set to affect the lobby will cause the following to occur: a. When the first partition that affects the lobby is disarmed, the lobby will also be disarmed. b. The common lobby cannot be armed unless every partition selected to affect the lobby is armed. c. Arming the last partition that affects the lobby will not automatically attempt to arm the lobby. Partitions set to arm the lobby will cause the following to occur: a. When the first partition that affects the lobby is disarmed, the lobby will also be disarmed. b. The common lobby cannot be armed unless every partition selected to affect the lobby is armed. c. Arming the last partition that is programmed to arm the lobby will automatically attempt to arm the lobby. If any faults exist in the lobby partition, or another partition that affects the lobby is disarmed, the lobby cannot be armed, and the message "UNABLE TO ARM LOBBY PARTITION" will be displayed.
The following chart sums up how the common lobby partition will operate.
Partition Affects Lobby NO YES YES NO Partition Arms Lobby NO NO YES YES Disarms when Attempts to arm when Can be armed if partition disarms? partition arms? other partitions disarmed? NO NO YES YES NO NO YES YES NO ---ENTRY NOT ALLOWED---
How User Codes Affect the Common Lobby

Codes with "Global" Arming If your code is given "global arming" when it is defined the keypad will ask "Arm all?" or "Disarm all?" whenever you try to arm or disarm the partitions you have access to from an alpha keypad. This allows you to pick and choose the partitions to be armed or disarmed, and so eliminates the "automatic" operation of the lobby. Keep in mind, however, that if attempting to arm all, and another "affecting" partition is disarmed, you will not be able to arm the lobby, and the message "UNABLE TO ARM LOBBY PARTITION" will be displayed. Codes with "Non-Global" Arming If arming with a non-global code, or if arming with a global code from a non-alpha keypad, the lobby partition operation will be automatic, as described in the previous table.
Other Methods of Arming/Disarming When arming or disarming a partition that affects and/or arms the common lobby in one of the following manners, lobby logic remains active: Quick-Arm Keyswitch Wireless Button Wireless Keypad

CHECKING FOR OPEN ZONES

Using the D READY Key Before arming your system, all protected doors, windows and other protection zones must be closed or bypassed (see BYPASSING section). Otherwise the keypad will display a "Not Ready" message. Using the READY key will display all zones that are faulted, making it easier for you to secure any open zones. To show faulted zones:
DISARMED PRESS G TO SHOW FAULTS Note: Some keypads light a green LED when the system is ready. If not lit, the system is not ready to be armed.
1. Do not enter security code, but simply press
FAULT 005 FRONT UPSTAIRS BEDROOM

Typical fault display

DISARMED READY TO ARM
Secure or bypass the zones displayed before arming the system. The "Ready" message will be displayed when all protection zones have been either closed or bypassed.
NOTE: All or part of this message may be replaced by a customized message programmed by the installer. Bear this in mind whenever the instructions indicate that the "DISARMED" or "READY" message will be displayed.
DISPLAYING ALL ZONE DESCRIPTORS
Using the D READY Key The Alpha Keypads can also display all the zone descriptors that are programmed in your system. The abbreviated instructions for the R E A D Y key will appear first, followed by the zone descriptors. Displaying all descriptors is useful when you need to know the zone number of a particular zone, as when bypassing zones. The "Disarmed-Ready to arm" message must be displayed before zone descriptors can be displayed.

Disarming

CHIME MODE
Using the 9 Key Your system can be set to alert you to the opening of a door or window while it is disarmed by using CHIME mode. When activated, three tones will sound at the Keypad whenever a protected perimeter door or window is opened, and the Not Ready message will be displayed. Pressing the READY key will display the open protection points. Note that Chime mode can be activated only when the system is disarmed. 1. To turn Chime Mode on, enter the security code and press 9.
CHIME MODE ON The CHIME MODE ON message will appear for about two seconds then disappear. To display this message again (to determine whether chime mode is on or off), simply press and hold down the CHIME key for 5 seconds.
2. To turn Chime Mode off, enter the security code and press 9 again.
CHIME MODE OFF The CHIME MODE OFF message will appear for about two seconds then disappear. To display this message again (to determine whether chime mode is on or off), simply press and hold down the CHIME key for 5 seconds.
VIEWING CENTRAL STATION MESSAGES
General Information Users of the system may periodically receive messages on their display screens from their monitoring agency or installer. When a message is waiting to be viewed, the message shown below will appear.
MESSAGE. PRESS 0 FOR 5 SECS.
1. Press and hold down 0 key for 5 seconds. 2. The message could take up to four screens to display all the information available.

PANIC KEYS

(FOR MANUALLY ACTIVATING SILENT AND/OR AUDIBLE ALARMS)
Using Panic Keys Your system may have been programmed to use special key combinations to manually activate panic functions. The functions that might be programmed are Silent Emergency, Audible Emergency, Personal Emergency, and Fire. See your installer for the function(s) that may have been programmed for your system. Active Panic Functions To use a paired key
(your installer should note which function(s) is active in your system)
Keys 1 and D 3 and # D and # A* B* C*

Zone 99 96

Function
* May not be present on your keypad(s).
panic function, simply press both keys of the assigned pair at the same time. If your keypad(s) have lettered keys for panic functions, press the designated key and hold down for at least 2 seconds to activate the panic function.
A silent emergency sends a silent alarm signal to the central station, but there will be no audible alarms or visual displays. An audible emergency sends an emergency message to the central station (if connected) and will sound a loud, steady alarm at your keypad and at any external sounders that may be connected (A L A R M plus a zone number would also be displayed). A personal emergency alarm sends an emergency message to the central station (if connected) and will sound at Keypads, but not at external bells or sirens. (ALARM plus a zone number would also be displayed) A fire alarm sends a fire alarm message to the central station and will uniquely sound external bells and sirens (FIRE plus a zone number would also be displayed).

Arm/Disarm Windows Disarm Window Start Time HH:MM Stop Time HH:MM Arm Window Start Time HH:MM Stop Time HH:MM Mon Tue Wed Thu Fri Sat Sun
Programming Temporary Schedules Temporary schedules only affect the partition from which it is entered. Temporary schedules can be reused at later dates simply by scrolling (by pressing #) to the DAYS? prompt (described below) and activating the appropriate days. This should be considered when defining daily time windows. Note that only users with authority level of manager or higher can program temporary schedules. To program temporary schedules: 1. Enter your security code. 2. Press the # key followed by 81. 3. The following prompts will appear.
MON DISARM WIND. 07:45AM 08:45AM The cursor will be positioned on the tens of hours digit of the start time for Monday's disarm window. Enter the desired hour. Press * to move to the minutes field. The minutes are entered in the same manner. The AM/PM indication is changed by hitting any key, 0-9, while the cursor is under the letter A/P position. Repeat for the stop time entry. Press the * key to move to the arming window for Monday. Press # to move to the next screen display without making changes. The cursor will be positioned on the tens of hours digit of the start time for the arm window. Repeat the previous steps to enter the start and stop time for Monday's arming window.
MON ARM WINDOW 07:45AM 08:45AM
Programming Temporary Schedules (continued)
TUE DISARM WIND. 07:45AM 08:45AM After the windows for that day have been completed, the system will prompt for disarm and arm time windows for the next day. Repeat the procedure for all days of the week. When all of the days have been completed, the system will ask which days are to be activated. This is the prompt that actually activates the temporary schedule, and allows the temporary schedule to be customized to a particular week's needs. To select the days which are to be activated, enter the desired number 1-7 (Monday = 1). An "X" will appear under that day, indicating the previously entered schedule for that day is active. Entering a day's number again will deactivate that day. Pressing 0 will turn all days on/off. The temporary schedule will only be in effect for the days which have the letter x underneath them. As the week progresses, the days are reset to the deactive state. When completed, press * to exit the temporary schedule entry mode.

DAYS MTWTFSS HIT 0-7 X X

PROGRAMMING DEVICE TIMERS

General Information

Device timers consist of an ON time & an OFF time, and selected days of the week in which they are active. There are up to 20 timers that can be used to control various devices, such as lights or appliances. Your installer will have programmed the appropriate devices into the system (up to 16 devices can be programmed). Each timer controls a single device (designated as an output number) that you select. For example, timer 1 might be set to turn the porch lights on at 7:00pm and turn them off at 11:00pm. Timer 2 might turn on the air conditioner Monday-Friday at 4:30pm to cool the premises before you arrive at 5:00pm, and turn it off at 10:00pm when you are retiring for the night. If desired, different timers can control the same device. For example, timer 2 could be used Monday-Friday as in the previous example, and timer 3 could be set to turn the air conditioner on and off at different times Saturday and Sunday. To enter the device timer menu mode: Enter your security code, then press the # key followed by 83.

OUTPUT TIMER # ? 01-20,00=QUIT 01 Up to 20 timers can be programmed. Each timer is identified by a number 1-20. Enter the desired timer number to be programmed (1-20). Press * to accept entry. If that timer number has already been programmed, a summary screen will appear. In this example:
06 = Timer # 04 = Output Device # affected by this timer PORCH LITE = Output Descriptor for Device 4 07:00PM = Start Time; 11:45PM = Stop Time
06 07:00P 11:45P PORCH LITE 04

Press * to continue.

See your installer for device numbers.

00 ENTER OUTPUT# 00

Enter the desired output device number (116). As the number is entered, the device's description will appear. To delete a previously programmed timer, enter 00 as the output number.
PROGRAMMING DEVICE TIMERS (cont'd)
00 ON TIME ? 00:00 PM Enter the time you want the device turned on using 00:01 - 11:59 format. When the display shows the desired time, press the * key to move to the AM/PM field. Press any key 0-9 to change the AM/PM indication. Enter 00:00 if this timer is not being used to turn something ON for the days selected below. (ex. using one timer to turn lights on one day and using another timer to turn them off on another day). Enter the time you want the device turned off using 00:01 - 11:59 format. When the display shows the desired time, press the * key to move to the AM/PM field. Press any key 0-9 to change the AM/PM indication. Enter 00:00 if this timer is not being used to turn something OFF for the days selected below. (ex. using one timer to turn lights on one day and using another timer to turn them off on another day). Select the days on which the device is to be activated by entering 1-7 (Monday = 1). An "X" will appear under that day, indicating the output for that day is active. Entering a day's number again will deactivate that day. Pressing 0 will turn all days on/off. The outputs will only be in effect for the days which have the letter x underneath them. As the week progresses, the selected days are reset to the inactive state, unless the permanent option is selected (next screen prompt). When completed, press * to continue. Answering 1 (yes) means the system will continue executing this timer on a continuous basis. An answer of 0 means execute each day's output only once.

00 OFF TIME ? 00:00 PM

00 DAYS? MTWTFSS HIT 0-7 X X
00 PERMANENT ? 0 = NO, 1 = YES 0
TESTING THE BURGLARY SYSTEM

(TO BE CONDUCTED WEEKLY)

Using the 5 TEST Key The TEST key puts your system into the Walk Test mode, which allows each protection point to be checked for proper operation. 1. Disarm the system and close all protected windows, doors, etc. READY should be displayed.
2. Enter your security code and press the

5 key.

3. The external sounder should sound for 3 seconds and then turn off. If the sounder does not sound, it may be due to dialer communication activity. Wait a few minutes and try again. If the sounder still does not sound, CALL FOR SERVICE IMMEDIATELY. 4. The keypad will sound a single beep every 15 seconds as a reminder that the system is in Test mode.
Note that no alarm reports will be sent to the central monitoring station while the system is in Test mode.
5. Open and close each protected door and window in turn and listen for three beeps. The identification of each faulted protection point should appear on the display. 6. Walk in front of any interior motion detectors (if used) and listen for three beeps as movement is detected. The identification of the detector should appear on the display when it is activated. If a problem is experienced with any protection point (no confirming sounds, no display), CALL FOR SERVICE IMMEDIATELY. 7. Turn off Test mode by entering the security code and pressing the OFF key.

FIRE ALARM SYSTEM

General Your fire alarm system (if installed) is on 24 hours a day, providing continuous protection. In the event of an emergency, the installed smoke and heat detectors will automatically send signals to your Control/Communicator, triggering a loud, interrupted sound from the Keypad. An interrupted sound will also be produced by optional exterior sounders. A FIRE message will appear at your Keypad and remain on until you silence the alarm. 1. Should you become aware of a fire emergency before your detectors sense the problem, go to your nearest Keypad and manually initiate an alarm by pressing the panic key pair assigned as FIRE emergency (if programmed by the installer) and hold down for at least 2 seconds. 2. Evacuate all occupants from the premises. 3. If flames and/or smoke are present, leave the premises and notify your local Fire Department immediately. 4. If no flames or smoke are apparent, investigate the cause of the alarm. The zone descriptor of the zone(s) in an alarm condition will appear at the Keypad. 1. Silence the alarm by entering your code and pressing the OFF key. To clear the display, enter your code and press the OFF key again. 2. If the Keypad does not indicate a READY condition after the second OFF sequence, press the READY key to display the zone(s) that are faulted. Be sure to check that smoke detectors are not responding to smoke or heat producing objects in their vicinity. Should this be the case, eliminate the source of heat or smoke. 3. If this does not remedy the problem, there may still be smoke in the detector. Clear it by fanning the detector for about 30 seconds. 4. When the problem has been corrected, clear the display by entering your code and pressing the OFF key.

DINING KITCHEN

TV ROOM

BEDROOM BEDROOM

KITCHEN

DINING

BDRM BDRM

BEDROOM

LIVING ROOM
s Smoke Detectors for Minimum Protection 7 Smoke Detectors for Additional Protection v Heat-Activated Detectors 7

LVNG RM

CLOSED DOOR GARAGE

BASEMENT

RECOMMENDATIONS FOR PROPER PROTECTION (cont.)
In addition, we recommend the following: Install a smoke detector inside every bedroom where a smoker sleeps. Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway outside may not wake up the sleeper if the door is closed. Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air conditioners or humidifiers) are used. Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters) long. Install smoke detectors in any room where an alarm control is located, or in any room where alarm control connections to an AC source or phone lines are made. If detectors are not so located, a fire within the room could prevent the control from reporting a fire or an intrusion. RECOMMENDATIONS FOR PROPER INTRUSION PROTECTION For proper intrusion coverage, sensors should be located at every possible point of entry to a home or commercial premises. This would include any skylights that may be present, and the upper windows in a multi-level building. In addition, we recommend that radio backup be used in a security system so that alarm signals can still be sent to the alarm monitoring station in the event that the telephone lines are out of order (alarm signals are normally sent over the phone lines, if connected to an alarm monitoring station).

EMERGENCY EVACUATION

Establish and regularly practice a plan of escape in the event of fire. The following steps are recommended by the National Fire Protection Association: 1. Position your detector or your interior and/or exterior sounders so that they can be heard by all occupants. 2. Determine two means of escape from each room. One path of escape should lead to the door that permits normal exit from the building. The other may be a window, should your path be impassable. Station an escape ladder at such windows if there is a long drop to the ground. 3. Sketch a floor plan of the building. Show windows, doors, stairs and rooftops that can be used to escape. Indicate escape routes for each room. Keep these routes free from obstruction and post copies of the escape routes in every room. 4. Assure that all bedroom doors are shut while you are asleep. This will prevent deadly smoke from entering while you escape. 5. Try the door. If the door is hot, check your alternate escape route. If the door is cool, open it cautiously. Be prepared to slam the door if smoke or heat rushes in. 6. Where smoke is present, crawl on the ground; do not walk upright. Smoke rises and may overcome you. Clearer air is near the floor. 7. Escape quickly; don't panic. 8. Establish a common meeting place outdoors, away from your house, where everyone can meet and then take steps to contact the authorities and account for those missing. Choose someone to assure that nobody returns to the house many die going back.

"FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 NOTICE This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company. This equipment uses the following jacks: An RJ31X is used to connect this equipment to the telephone network. The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe necessary. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service. If trouble is experienced with this equipment, please contact the manufacturer for repair and warranty information. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved. There are no user serviceable components in this product, and all necessary repairs must be made by the manufacturer. Other repair methods may invalidate the FCC registration on this product. This equipment cannot be used on telephone company-provided coin service. Connection to Party Line Service is subject to state tariffs. This equipment is hearing-aid compatible. When programming or making test calls to an emergency number, briefly explain to the dispatcher the reason for the call. Perform such activities in the off-peak hours; such as early morning or late evening.
CANADIAN DEPARTMENT OF COMMUNICATIONS (DOC) STATEMENT
NOTICE The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company's inside wiring associated with a single line individual service may be extended by means of certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Caution: User should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all the devices does not exceed 100. AVIS L'tiquette du ministre des Communications du Canada identifie le matriel homologu. Cette tiquette certifie que le matriel est conforme certaines normes de protection, d'exploitation et de scurit des rseaux de tlcommunications. Le ministre n'assure toutefois pas que le matriel fonctionnera la satisfaction de l'utilisateur. Avant d'installer ce matriel, l'utilisateur doit s'assurer qu'il est permis de le raccorder aux installations de l'entreprise locale de tlcommunications. Le matriel doit galement tre install en suivant une mthode accepte de raccordement. Dans certains cas, les fils intrieurs de l'entreprise utiliss pour un service individuel la ligne unique peuvent tre prolongs au moyen d'un dispositif homologu de raccordement (cordon prolongateur tlphonique interne). L'abonn ne doit pas oublier qu'il est possible que la conformit aux conditions nonces ci-dessus n'empchet pas la dgradation du service dans certaines situations. Actuellement, les entreprises de tlcommunications ne permettent pas que l'on raccorde leur matriel aux prises d'abonns, sauf dans les cas precis prvus par les tarifs particuliers de ces entreprises. Les rparations du matriel homologu doivent tre effectues pas un centre d'entretien canadien autoris dsign par le fournisseur. La compagnie de tlcommunications peut demander l'utilisateur de dbrancher un appareil la suite de rparations ou de modifications effectues par l'utilisateur ou cause de mauvais fonctionnement. Pour sa propre protection, l'utilisateur doit s'assurer que tous les fils de mise en terre de la source d'nergie lectrique, des lignes tlphoniques de rseau de conduites d'eau s'il y en a, soient raccords ensemble. Cette prcaution est particulirement importante dans les rgions rurales. Avertissement: L'utilisateur ne doit pas tenter de faire ces raccordements lui-mme; il doit avoir recours un service d'inspection des installations lectriques, ou un lectricien, selon le cas. L'indice de charge (IC) assign chaque dispositif terminal pour viter toute surcharge indique le pourcentage de la charge totale qui peut tre raccord un circuit tlphonique boucl utilis par ce dispositif. La terminaison du circuit boucl peut tre constitue de n'importe quelle combinaison de dispositifs, pourvu que la somme des indices de charge de l'ensemble des dispositifs ne dpasse pas 100.

WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example: Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. A user may not be able to reach a panic or emergency button quickly enough. While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death. Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90 to 105F, the detection performance can decrease.