ADEMCO VISTA-128FB/V128FB-24
Commercial Fire and Partitioned Alarm Platform
Designed to integrate seamlessly with CCTV, access control and Honeywells full range of fire and burglary components, the VISTA-128FB provides the ultimate protection of life and property. The UL listed Commercial Fire and Burglary Control Platform controls up to eight partitions, and supports up to 128 zones/points using hardwired, wireless and
addressable V-Plex technologies. A diverse line of Honeywell initiating devices, notification circuits, digital dialers, keypads, RF receivers and relays support this extremely powerful control platform. The VISTA-128FB has been designed to mount quickly and easily in an attack resistant cabinet, and is available in 12V and 24V models.

F E AT U R E S

Supports addressable V-Plex access control points using VistaKey (1 to 8 doors) Supports up to 15 doors of access control using Vista Gateway Module (VGM)* Supports CCTV applications with the new VistaView-100 CCTV switcher module Identifies the point or zone of a fire or alarm, using the new FSA-8/ FSA-24 Fire system annunciator Stores up to 512 events and can accommodate 150 user codes New E2 software simplifies programming Easily programmed and maintained with newly upgraded Compass Downloader software Eight hardwired zones standard, expandableto 120 V-Plex addressable points/zones or 128 wireless points/zones Can control eight separate areas independently (8 partitions) Two on-board notification (bell) circuits delivering 2.3A @ 12V or 3.4 amp @ 24V Automatic smoke detector sensitivity maintenance testing
* Connects to Honeywells Passpoint Access Control Systems. Maximum 32 doors.
S P E C I F I C AT I O N S
Cabinet dimensions 18"H X 14.5"W X 4.3"D Environmental Storage temp: -10C to 70C Operating temp: 0C to 50C Humidity: 85% RH EMI Meets or exceeds the following requirements: FCC Part 15, Class B Device FCC Part 68 IEC EMC Directive Agency Listings Burglary UL609 Grade A Local Mercantile Premises and Mercantile Safe and Vault UL611/1610 Grades A, AA, Central Station UL365 Grades A, AA Police Connect Fire UL864/NFPA72 Local, Central Station and Remote Station Factory Mutual California State Fire Marshal MEA UL985 Additional Features Notification Appliance Circuits (two) Programmable Temporal code compliant Individually silenceable Programmable on-board auxiliary relay SIA false alarm reduction features: Exit Error Logic Exit Delay Reset Cross Zoning Call Waiting Defeat Recent Close Report Supports commercial hardwired, addressable V-Plex polling loop and wireless zones Hardwired zones: Provides nine style B hardwired zones EOLR supervised for Fire and UL burglary installations Supports N.0 or N.C. sensors Individually assignable to one or all eight partitions Up to 16 two-wire smoke detectors each zone 1 and 2 (32 total) Up to 50 two-wire glass break detectors on zone eight Patented addressable V-Plex polling loopV-Plex technology: Supports up to 120 two-wire zones/points Global polling technology for faster processing Increased current draw capacity (128mA) Supervised by panel Individually assignable to partitions, notification circuit (bell) output or aux relay 4,000 ft capability without the use of shielded cable Extender/Isolation bus module Two-wire smoke detector zone/group expansion module adds two or four zones Eight zone - Class A and B Extender Module One zone supervised Contact Monitor Module UL Listed wireless expansion Supports up to 128 wireless zones using 5881 Receiver

VPlex Loop

9500SN Glassbreak Sensor

4101SN Relay Module

4208U Eight-Zone Expansion Module

4293SN V-Plex Adapter

5192 Series Smoke Detectors

V-PLEX Loop

4208SNF Eight-Zone Expansion Module With Two Class A 5881ENHC Zones Wireless Commercial Receiver
6160CR Custom Alpha Console
VistaKey V-Plex Access Control Module
VistaView-100 CCTV Switcher

Notification Appliances

4204 Relay Module
NAC (Bell) Circuit 4204CF
Eight Class B Hardware Zones 4146 Key Switch Option 5140 LED Communicator Status Module
4100SM Printer Interface Module RS232 6220S Printer Phone Line to Central Station Notification Appliances

7720ULF Long Range Radio

7845C Cellular

Supervised by control for check-in signals Tamper protection for transmitters Individually assignable up to eight partitions Supports UL864/NFPA approved wireless smoke detectors Access control integration Full integration with PassPoint Access Control System Complete Gateway in access functions Event reporting Local printer of access or VISTA related event Scheduled uploading of events to central station Stored events for one call retrieval Communication Phone mapping by zone response type Supports VIP Interactive Phone Voice Module Panel operation during download Uploading equipment list to central station Communication to PassPoint via Vista Gateway Module (VGM)
Applications Supported by a diverse line of Honeywell initiating devices, the powerful VISTA-128FB is the ideal integrated fire and burglary control for applications where a higher level of security is necessary including medical and professional buildings, supermarkets, churches and synagogues, office buildings, schools, universities, strip malls, larger residences and factory or warehouse environments. Installation The VISTA-128FB alarm system has been designed to mount both quickly and easily in an attack resistant cabinet. It meets all applicable requirements for UL commercial burglary installations. Electrical: Primary power: 18 VAC@ 72 VA No. 1451 Quiescent current draw: 300mA Backup battery 12VDC, 12AH min to 34AAH max Lead acid battery (gel type)
Alarm power 12VDC, 1.7A max for each notification (bell) circuit output Aux. standby power 12VDC, 1A max Total power 2.3A at 12VDC, 3.4A at 24VDC from all sources Standby time 24 hours with 1A standby load or 60 hours with 205mA max standby load using 34AAH battery Fusing Battery input, aux. and notification (bell) circuit outputs are protected using PTC circuit protectors. All outputs are power limited. Main dialer Line seize: Double Pole
Manual Pull Stations 5140MPS - 1* 5140MPS - 2* Q2260SN Multiplex DUAL TEC Motion Detector 4944SN Addressable Recessed Mount Contact

4278EX Quad PIR

4193SN Serial Interface Module
4190SN V-Plex Two-Zone Expander

ECP Bus

5881 Wireless Receiver (Max Two)
Tamper Switch* Flow Switch* Low Temp Switch*

6139R 32 Character Red-Alpha Keypad
5808LST Smoke Detectors 5800 Series Wireless Devices 5816 Door/Window Miniature Transmitter Notification Appliance 5869 Commercial Hold-Up Switch
5890 Wireless PIR 4209U Group Zoning Module 5808LST Smoke Detectors
4204CF Supervised NAC Module
Supports Up To 16 Conventional Two-Wire Smoke Detectors
5817CB Wireless Commercial Transmitter
Supports Up To 64 Conventional Two-Wire Smoke Detectors
VGM (PTVGM) Vista Gateway Module PassPoint
Ringer equiv. 0.713 Formats: ADEMCO Low Speed, ADEMCO 4+2 Express, ADEMCO High Speed, ADEMCO Contact ID, Sescoa and Radionics Auxiliary devices 6160CR Alpha Keypad Commercial Fire 6139R - Red Alpha Keypad/Annunciator FSA-8 & FSA-24 Fire System Annunciator 4204 - Relay Module, four form C contacts 4204CF - Two supervised output circuits 6220S - System printer used with 4100SM Serial Interface Module 5140DLM, FSA-8, FSA-24, FSAKSM Fire Annunciator Two-wire and four-wire smoke detectors conventional: System Sensor smoke detectors Horn/Strobes System Sensor notification appliances Manual pull stations: 5140MPS-1 5140MPS-2 V-Plex (addressable) devices: 4101SN Single Relay/Zone Module 4190SN Remote Point Module two zones 4190WH Two Point Multiplex RPM 4193SN Two Zone Serial Interface Module 4208U Loop Expansion Module eight zones 4208SNF Class A/13 Expander Module 4209U Group Zoning Module two/four zones 4293SN One Zone Serial Interface Module 4297 Isolation/Extender Module V-Plex (addressable) smoke detectors 5192SD 5192SDT Passive infrared detectors 998MX 4275EX-SN 4278EX-SN Quest 2260SN V-Plex (addressable) contacts 4939SN-WH 4944SN-WH 4959SN Glassbreak detectors 9500SN VISTA Interactive Phone Module 4286 Voice Module Optional 24V power supply PS24 - 24V power supply - 3.4A Long range radio Long range radio 7720ULF-XX, 7845C, 7835CFPK Upgraded software Upgraded Compass Downloader Windows compatible Wireless devices 5804 - Wireless Key 5804BD - Bi-Directional Key 5804BDV - Bi-Directional with voice 5816 - Door/Window Transmitter 5819 - Shock Sensor 5827BD - Bi-Directional Keypad 5849 - Glassbreak Detector 5881 Series - RF Receiver supporting 5800 wireless detectors 5890 - PIR Access control VistaKey V-Plex (addressable) Access Control VistaKey-SK Starter Kit VistaKey-EX Expansion Kit VGM Vista Gateway Module to PassPoint Access Control (Honeywell Access Systems) CCTV VistaView-100-CCTV Switch Module Commercial wireless devices 5869 - Hold up Transmitter 5817CB - Wireless Commercial Transmitter 5881ENHC - Commercial Fire/Burg Receiver 5808LST - Wireless Smoke Detector 5809 - Wireless Heat Detector

ORDERING

VISTA-128FB V128FB-24 Commercial Fire and Partitioned Burglary Alarm Platform 12V Model Commercial Fire and Partitioned Burglary Alarm Platform 24V Model
Honeywell Security & Custom Electronics 165 Eileen Way, Syosset, NY 11791 www.ademco.com
Copyright 2004 Honeywell International Inc. L/VIS128FB/D 1/04
6160CR Custom Alpha Console 6139R 32 Character Red-Alpha Keypad 5808LST Smoke Detectors 5800 Series Wireless Devices 5816 Door/Window Miniature Transmitter Notification Appliance 5869 Commercial Hold-Up Switch 5890 Wireless PIR 4209U Group Zoning Module 5808LST Smoke Detectors

-- 7 --

Master Keypad Operation
A "Master" keypad is one on which the status of all 8 partitions is displayed simultaneously. A user can get more information about a certain partition by simply entering [F] + the desired partition number (1-8). To log on to the "Master" partition (9) using the GOTO command, a user must have access to all partitions.

Self-Help Feature

Abbreviated user's instructions are built into the system that can be easily viewed on the alpha keypad's message display screen. This feature will prove particularly useful if this manual is not conveniently accessible when you need to perform a system procedure with which you are not familiar. To view the abbreviated instructions: Simply press and hold down the function key of interest until the description starts to appear (about 5 seconds) and then release it. Refer to the FUNCTIONS OF THE KEYPAD section for descriptions of each key function.

-- 8 --

Phone Access & Voice Response Capability
Your system may include a 4285 or 4286 VIP module that will permit you to access the system via a Touch-tone phone, either on-premises or by call-in when away. The phone access feature will enable you to do the following: Receive synthesized voice messages over the telephone regarding the status of the security system. Arm and disarm the system and perform most function commands via the telephone, with voice confirmation provided after each command entry. Control 4204/4204CF relays devices through the #70 Manual Relay Activation mode.
Complete information regarding the use of this feature is provided in a separate manual entitled PHONE ACCESS USER'S GUIDE, which accompanies the 4285 or 4286 VIP module.

-- 9 --

About The Keypads
IMPORTANT: If the keypad beeps rapidly upon entering the premises, it indicates that an alarm has occurred during your absence. LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location.
Your keypads allow you to control all system functions. The keypads feature a telephone style (digital) keypad and a Liquid Crystal Display (LCD) which shows the nature and location of all occurrences. Keypad display back lighting is programmable to always stay on or to light only when a key is pressed, then turn off a few minutes later. The keypads also feature a built-in sounder which will sound during alarms and troubles. It will also "beep" during certain system functions, such as during entry/exit delay times, during CHIME mode, and when depressing keys to arm and disarm the system (to acknowledge the key press). These sounds can be optionally suppressed in some of your keypads (so as not to disturb other users of the system). Ask your installer if this has been done.

9. CODE KEY: Allows the entry of additional user codes that can be given to other users of the system. 10. CHIME KEY: Turns on & off the CHIME mode. When on, any entry through a protected delay or perimeter zone while the system is disarmed will cause a tone to sound at the Keypad(s). 11. READY KEY: When depressed prior to arming the system, the keypad will display all open protection zones within the keypad's home partition. This key is also used to display all zone descriptors that have been programmed for your system, by holding the key down for at least 5 seconds. 12. # KEY: Permits ARMING of the system without use of a security code ("Quick Arm", if programmed). 13. KEYS 0-9: Used to enter your individual security access code(s). 14. POWER/READY INDICATOR: (GREEN) On some keypads, this lights when primary power is on. If off, system is operating on its backup battery power. CALL YOUR INSTALLER IMMEDIATELY. On other types of keypads, lit indicates system is ready to be armed, while unlit indicates system not ready. 15. ARMED INDICATOR: (RED) Lit when the system has been armed (STAY, AWAY, INSTANT or MAXIMUM). 16. INTERNAL SOUNDER: Source of audible internal warning and confirmation sounds, as well as alarms (see "Summary of Audible Notifications"). 17. A-B-C PANIC KEYS: Refer to the PANIC KEYS section for descriptions of these keys.

-- 13 --

Entry/Exit Delays

General Information

Your system has preset time delays, known as exit delay and entry delay. Whenever you arm your system, exit delay gives you time to leave through the designated exit door without setting off an alarm. Exit delay begins immediately after entering any arming command, and applies to all modes of arming protection. If programmed, a slow beeping will sound throughout the exit delay period. Entry Delay gives you time to disarm the system when you reenter through the designated entrance door. But the system must be disarmed before the entry delay period ends, or an alarm will occur. The keypad will beep during the entry delay period, reminding you to disarm the system. You can also arm the system with no entry delay at all by using either INSTANT or MAXIMUM arming modes. These modes provide greater security while on the premises or while away for extended periods of time. See your installer for your delay times.

-- 14 --

Security Codes & Authority Levels
At the time of installation, you were assigned an authority level and a personal four-digit security code, known only to you and yours. The security code must be entered when arming and disarming the system. The authority level defines the system functions that you can perform. Additionally, other users that do not have a need to know your code can be assigned different security codes, and each user can be given a different authority level. Users are identified by "user numbers", which are assigned when assigning a user's security code. All codes can be used interchangeably when performing system functions within the limits of each code's authority level (a system armed with one user's code can be disarmed by another user's code), with the exception of the Operator Level C code. See AUTHORITY LEVELS section on the following page for detailed information regarding user authority levels.

Duress Code

This feature is intended for use when you are forced to disarm or arm the system under threat. When used, the system will act normally, but can silently notify the central station of your situation, if that service has been provided. The duress code is pre-assigned by the installer during installation (auth. level 6). Important: This code is useful only when the system is connected to a central station.

Quick Arming

Note that if "Quick Arming" was programmed by the installer, the [#] can be pressed in place of the security code when arming the system. The security code must always be used to disarm the system.

-- 15 --

Security Codes & Authority Levels (contd)

Authority Levels

Authority levels define the system functions a particular user can perform. Depending on the authority assigned to you, there are certain system functions you may be prohibited from performing. In summary, there are six authority levels, each having certain system restrictions as shown below. Level 1 Master: Can perform all system functions in assigned partitions, and can add, delete or change Manager and Operator level users. Master codes are added by the Installer. Can perform system functions in assigned partitions, and can add, delete or change Operator level users. Can perform system functions in assigned partitions, but cannot add or delete other users. Same as Operator A, except Operator B cannot bypass zones of protection. Can arm the system in assigned partitions, but cannot disarm the system unless the system was armed with this code. This code is typically assigned to someone who has a need to arm/disarm the system only at certain times (such as a baby-sitter). Can arm and disarm the system, but also sends a silent panic alarm to the central station, if that service is connected.

Level 2 Manager:

Level 3 Operator A:
Level 4 Operator B: Level 5 Operator C:

Level 6 Duress:

-- 16 --
To view your authority level and system capabilities: 1. Enter your code + [F] + [F]. 2. The keypad will display the partition(s) that you are authorized to operate, and your user number and authority level in each partition.
General Rules on Authority Levels and Changes
A user may not delete or change the user code of the SAME or HIGHER authority than which he is assigned. A user may only ADD users to a LOWER authority level. A user may assign access codes only to those partitions to which the user adding the code has access. (ex. a user with access to only partition 1 cannot assign codes in partition 2.) The only way to assign a user's authority level is by using the "Add A User" procedure. To change a user's authority level, that user must first be deleted, then added again. A user can only be DELETED or CHANGED from within the partition he is assigned. User numbers must be entered as 3-digit entries. Single digit user numbers must be preceded by a "00" (example, 003, 004, etc.). Security codes are entered as 4-digit numbers. Before assigning a security code, be sure it does not conflict with any DURESS code.

When finished, the keypad will display the word BYPASS along with each bypassed zone number. Wait for these zones to be displayed before arming. Arming the system before bypassed zones are displayed eliminates all bypasses. Arm the system as usual when the keypad displays "ready" to arm message.
DISARMED BYPASS READY TO ARM

-- 29 --

Bypassing Protection Zones (contd)

Quick Bypass

Your system allows you to easily bypass all open (faulted) zones without having to enter zone numbers individually. Note: All bypasses are removed when an OFF sequence (security code plus OFF) is performed. To use the Quick Bypass feature:
1. Enter your security code and press[6] then press [#]. 2. BYPASS 007 FRONT
In a few moments, all open zones will be displayed along with the word BYPASS. Wait for these zones to be displayed before arming. Arming the system before bypassed zones are displayed eliminates all bypasses.
Arm the system as usual when the keypad displays the "ready" to arm message. Bypassed zones are unprotected and will not cause an alarm when violated while your system is armed.
Displaying Bypassed Zones
For determining what zones have been previously bypassed. Bypassed zones can be displayed only when system is disarmed.
1. Enter your security code and press [6]. 2. Wait for all bypassed zones to be sequentially displayed.

-- 30 --

Arming Perimeter Only

(With Entry Delay ON)

Using the [3] STAY key
Use this key when you are staying home, but might expect someone to use the entrance door later. When armed in STAY mode, the system will sound an alarm if a protected door or window is opened, but you may otherwise move freely throughout the premises. Late arrivals can enter through the entrance door without causing an alarm, but they must disarm the system within the entry delay period or an alarm will occur. Close all perimeter windows and doors before arming (see CHECKING FOR OPEN ZONES section)
1. Enter your security code and press [3]. 2.
ARMED ***STAY*** ZONE BYPASSED
The keypad will beep three times and will display the armed message. Note: "ZONE BYPASSED" in this display simply indicates that the interior zones of protection are not armed when using STAY mode.

-- 31 --

(With Entry Delay OFF)
Using the [7] INSTANT Key
Use this key when you are staying home and do not expect anyone to use the entrance door. When armed in INSTANT mode, the system will sound an alarm if a protected door or window is opened, but you may otherwise move freely throughout the premises. The alarm will also sound immediately if anyone opens the entrance door. Close all perimeter windows and doors before arming (see CHECKING FOR OPEN ZONES section).

1. Enter your security code and press [7]. 2.
ARMED *INSTANT* ZONE BYPASSED

-- 32 --

Arming All Protection

Using the [2] AWAY Key

Use this key when no one will be staying on the premises. When armed in AWAY mode, the system will sound an alarm if a protected door or window is opened, or if any movement is detected inside the premises. You may leave through the entrance door during the exit delay period without causing an alarm. You may also reenter through the entrance door, but must disarm the system within the entry delay period or an alarm will occur. Close all perimeter windows and doors before arming (see CHECKING FOR OPEN ZONES section)
1. Enter your security code and press [2]. 2.
ARMED **AWAY** YOU MAY EXIT NOW
The keypad will beep twice and will display the armed message. Note: The "YOU MAY EXIT NOW" portion of the message disappears when exit delay expires.

-- 33 --

Using the [4] MAXIMUM Key
Use this key when the premises will be vacant for extended periods of time such as vacations, etc., or when no one will be moving through protected interior areas. When armed in MAXIMUM mode, the system will sound an alarm if a protected door or window is opened, or if any movement is detected inside the premises. You may leave through the entrance door during the exit delay period without causing an alarm, but an alarm will be sounded as soon as someone reenters. Close all perimeter windows and doors before arming (see CHECKING FOR OPEN ZONES section).

MAXIMUM

1. Enter your security code and press [4]. 2.
ARMED *MAXIMUM* YOU MAY EXIT NOW

-- 34 --

Disarming And Silencing Alarms

Using the [1] OFF Key

The OFF key is used to disarm the system and to silence alarm and trouble sounds. See "SUMMARY OF AUDIBLE NOTIFICATION" section for information which will help you to distinguish between FIRE and BURGLARY alarm sounds. IMPORTANT: If you return and the main burglary sounder is on, DO NOT enter the premises, but call the police from a nearby safe location. If you return after an alarm has occurred and the main sounder has shut itself off, the keypad will beep rapidly upon entering, indicating that an alarm has occurred during your absence. LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location. To disarm the system and silence burglary or fire alarms:
1. Enter your security code and press [1].

DISARMED READY TO ARM

2. The Ready message will be displayed (if no alarms have occurred while armed) and the keypad will beep once to confirm that the system is disarmed.
The keypad displays the zone number and type of alarm for any zone that has an alarm condition. These messages will remain displayed until cleared by a user. If an alarm has occurred, note the zone number displayed on the keypad and repeat step 1 above to clear the "Memory of Alarm" and restore the Ready message display. If the Ready message will not display, go to the displayed zone and remedy the fault (close windows, etc.). If the fault cannot be remedied, notify the alarm agency. If the system was armed when the alarm occurred, repeat step 1 twice: once to disarm the system, a second time to clear the display.

-- 35 --

Using The Keyswitch
Your system may be equipped with a keyswitch for use when arming and disarming a partition. A red and green light on the keyswitch plate indicate the status of your system as follows: Green Light: Lights when the system is disarmed and ready to be armed (no open zones). If the system is disarmed and the green light is off, it indicates the system is not ready (one or more zones are open). Red Light: Lights when system is armed or memory of alarm exists. Lit Steady: Partition is armed in AWAY mode. Slow Flashing: Partition is armed in STAY mode. Rapid Flashing: Memory of alarm, indicating an alarm has occurred.

Arming

To arm in the AWAY mode, turn the key to the right for 1/2 second and release. Keypads will beep twice and the red light will stay on steady. To arm in the STAY mode, turn the key to the right and hold for longer than 10 seconds, then release. Keypads will beep three times and the red light will flash slowly.

Disarming

To disarm the partition, turn the key to the right and release. If an alarm has occurred, the red light will be flashing rapidly (memory of alarm).

-- 36 --

Chime Mode

Using the [9] Key

Your system can be set to alert you to the opening of a door or window while it is disarmed by using CHIME mode. When activated, three tones will sound at the Keypad whenever a protected perimeter door or window is opened, and the Not Ready message will be displayed. Pressing the READY key will display the open protection points. Note that Chime mode can be activated only when the system is disarmed. 1. To turn Chime Mode on, enter the security code and press [9].

CHIME MODE ON

The CHIME MODE ON message will appear for about two seconds then disappear. To display this message again (to determine whether chime mode is on or off), simply press and hold down the CHIME key for 5 seconds.
2. To turn Chime Mode off, enter the security code and press [9] again.

CHIME MODE OFF

The CHIME MODE OFF message will appear for about two seconds then disappear. To display this message again (to determine whether chime mode is on or off), simply press and hold down the CHIME key for 5 seconds.

-- 37 --

Viewing Central Station Messages
Users of the system may periodically receive messages on their display screens from their monitoring agency or installer. When a message is waiting to be viewed, the message shown below will appear.
MESSAGE. PRESS 0 FOR 5 SECS.
1. Press and hold down [0] key for 5 seconds. 2. The message could take up to four screens to display all the information available.

Voice: "voice descriptor DEVICE nn ON/OFF. FOR voice descriptor ON ENTER 1, FOR voice descriptor OFF ENTER 0" Press 0 or 1 to turn the device off or on respectively. "nn" represents the 2-digit device number and voice descriptor is the relay voice descriptor programmed by the installer.

-- 43 --

Using #70 Relay Menu Mode (contd)
NN DEVICE IS OFF HIT THE "T" KEY
Voice: "voice descriptor DEVICE nn ON/OFF. TO EXIT ENTER 00 NOW" From a keypad, press T to continue. The ENTER DEVICE NO. prompt will appear. From a telephone keypad, enter 00 to exit, or enter the next relay number to be programmed. The current on/off state of that relay will be annunciated as described above. Alternatively, if 6 seconds elapses with no key depression, the 4285 or 4286 VIP module will annunciate the "ENTER DEVICE CODE NOW" message.

-- 44 --

Delaying the Closing Time
Your system's programmed schedules may automatically arm the system at a predetermined time. In the event a user must stay on the premises later than usual, users with master or manager authority levels can manually delay the automatic arming (closing) time up to 2 hours. To delay the closing time: 1. Enter your security code (master or manager authority levels only). 2. Press the [#] key, followed by 82. 3. A menu prompt will be displayed, asking for the number of hours of delay.
CLOSING DELAY? HIT 0-2 HOURS
Enter the desired number of hours of delay, 1 or 2. The system will automatically exit this mode after entry.
Note that the delay is from the scheduled closing time, not from the time the command is entered. IMPORTANT: The selected delay cannot be reduced once it is set. A 1 hour delay can be increased to 2 hours, though. 4. The system will automatically send a message to the central station informing them that the programmed schedule has been changed.
Temporary Open/Close Schedules
Temporary schedules allow you to override the normal schedules programmed by the installer. Temporary schedules can be in effect for up to one week, and take effect as soon as they are programmed.

-- 45 --

Using Schedules (contd)
Schedules are comprised of an arming (closing) time window and a disarming (opening) time window. A time window is simply a defined period of time, at the end of which arming or disarming will occur. Before programming a temporary schedule, use a worksheet similar to the one below to plan your schedule. This will make it easier when actually programming the schedule.
Arm/Disarm Windows Disarm Window Start Time HH:MM Stop Time HH:MM Arm Window Start Time HH:MM Stop Time HH:MM Mon Tue Wed Thu Fri Sat Sun
Programming Temporary Schedules
Temporary schedules only affect the partition from which it is entered. Temporary schedules can be reused at later dates simply by scrolling (by pressing #) to the DAYS? prompt (described below) and activating the appropriate days. This should be considered when defining daily time windows. Note that only users with authority level of manager or higher can program temporary schedules. To program temporary schedules: 1. Enter your security code. 2. Press the [#] followed by 81. 3. The following prompts will appear.

00 PERMANENT ? 0 = NO, 1 = YES 0
Answering 1 (yes) means the system will continue executing this timer on a continuous basis. An answer of 0 means execute each day's output only once.

-- 51 --

Event Log Procedures
The system has the ability to record various events in a history log wherein each event is recorded in one of five categories (listed below), with the time and date of its occurrence. The Event Log holds up to 224 events, with the oldest event being replaced by the logging of any new event after the log is full. Using an alpha keypad, the Event Log can be viewed one category at a time, or can display all events, regardless of category (ALL EVENT LOG). The system also allows selection of displaying the COMPLETE log, or only those events occurring since the last installer service (RECENT). In addition, events in the other partitions can be viewed by users authorized to access those partitions. Note that events are displayed in chronological order, from most recent to oldest.

To Display The Event Log

1. Enter CODE + [#] + [6] + [0] 2. Select the display mode. RECENT: Displays only those events occurring since last installer service. COMPLETE: Displays complete event log (up to 224 events). Press the desired key, 0 or 1.
ENTER 0 = RECENT 1 = COMPLETE
4. Use the [3] & [1] keys (for next and previous categories respectively) to display the categories of events. Press [8] to select a category and display the first event. Press [8] again for each subsequent event. Shows burglary alarm occurred in zone 3 (C03) of partition 1 (P1), at 12:02AM on January 1.
P1 01/01 12:02AM BURGLARY C03
Typical Event Log Display
3. Select the partition, 0-8. Enter the partition number for the partition whose events are to be displayed. Entering 0 (NO) will display all partitions' events.
SCAN LOG BY PART 0=NO 1-8=PART #
After the last event has been displayed, the END OF EVENT LOG message appears for a few seconds, then the system automatically displays the RECENT/COMPLETE mode select screen again (see step 2).

-- 52 --

Event Logging Procedures (continued)
5. To EXIT the Event Log: Press [D] at any time.
ALARM EVENT LOG TYPE CCC UUU

Typical Category Select Screen
OPEN EVENT LOG Displays time, date and user number for each arming and disarming of the system for the partition selected. SYSTEM EVENT LOG Displays time and date for system problems, such as AC Loss, low battery, etc., regardless of partition. ALL EVENT LOG Displays all categories of events in chronological order. TEST EVENT LOG Displays list of periodic tests sent by panel.
ALARM EVENT LOG Displays time and date for zones that have either caused an alarm or have been restored in the selected partition. CHECK EVENT LOG Displays time and date for zones that have caused a trouble or supervisory condition in the selected partition. BYPASS EVENT LOG Displays time and date for zones that have been bypassed in the partition.
See your Installer for additional information concerning the event log.

-- 53 --

Testing The System

(To Be Conducted Weekly)

Using the [5] TEST Key
The TEST key puts your system into Test mode, which allows each protection point to be checked for proper operation. 1. Disarm the system and close all protected windows, doors, etc. READY should be displayed.
2. Enter your security code and press the [5] key. 3. The external sounder should sound for 3 seconds and then turn off. If the sounder does not sound, it may be due to dialer communication activity. Wait a few minutes and try again. If the sounder still does not sound, CALL FOR SERVICE IMMEDIATELY. 4. The keypad will sound a single beep every 15 seconds as a reminder that the system is in Test mode. Each time a protection zone is faulted (opened), the keypad should beep three times. If the sounder does not sound, CALL FOR SERVICE IMMEDIATELY.
Note that no alarm reports will be sent to the central monitoring station while the system is in Test mode.

-- 54 --

Testing The System (contd)

Testing Your System

1. Open and close each protected door and window in turn and listen for three beeps. The identification of each faulted protection point should appear on the display. 2. Walk in front of any interior motion detectors (if used) and listen for three beeps as movement is detected. The identification of the detector should appear on the display when it is activated. 3. Follow the manufacturer's instructions to test all smoke detectors to ensure that all are functioning properly. The identification of each detector (or the zone number of the zone assigned to the detector) should appear on the display when each is activated. 4. When all protection points have been checked, there should be no zone identification numbers displayed. If a problem is experienced with any protection point (no confirming sounds, no display), CALL FOR SERVICE IMMEDIATELY. 5. Turn off Test mode by entering the security code and pressing the OFF key.

-- 57 --

2. The test may be stopped by entering any security code and pressing OFF. NOTE: The system continues to monitor all 24 hour zones (fire, panic, etc.), while this test is active, and will end the test when an alarm condition is detected. This test should be conducted at periodic intervals as determined by the local authority having jurisdiction.

-- 58 --

Trouble Conditions

Typical Trouble Displays

The word CHECK or TRBL on the Keypad's display, accompanied by a rapid "beeping" at the Keypad, indicates that there is a trouble condition in the system. To silence the beeping sound for trouble conditions, press any key. A display of CHECK or TRBL accompanied by a display of "CALL SERVICE" indicates that a problem exists with the system that eliminates some of the protection. CALL FOR SERVICE IMMEDIATELY. A display of CHECK or TRBL" accompanied by a display of one or more zone descriptors indicates that a problem exists with those zone(s)*. First, determine if the zone(s) displayed are intact and make them so if they are not. If the problem has been corrected, the display of the zone descriptor(s) and CHECK or TRBL should disappear. If not, key an OFF sequence (Code plus OFF) to clear the display. If the display persists, CALL FOR SERVICE IMMEDIATELY. A display of CHECK or TRBL accompanied by a numeric display of 6XX, where XX = 01-32, indicates a trouble on a supervised relay (corresponding relay number 01-32). A display of CHECK or TRBL accompanied by a numeric display of 8XX, where XX = 00-31, indicates a trouble on a peripheral device (connected to the panels keypad terminals) of a corresponding device address (00-31).

-- 59 --

Trouble Conditions (contd)
A display of CHECK or TRBL accompanied by a numeric display of 9XX, where XX = 00-99, indicates a system trouble exists (dialers, bell outputs, ground fault, etc.). These zones are as follows: 970: Bell 1 Output 971: Bell 2 Output 972: Earth Ground Fault 973: J2 Trigger Output 974: Dialer 1 975: Dialer 2 988: 2nd RF Receiver not receiving signals 990: 1st RF Receiver not receiving signals 997: Polling Loop Short
A display of "COMM. FAILURE" at the Keypad indicates that a failure has occurred in the telephone communication portion of your system. CALL FOR SERVICE IMMEDIATELY. A display of "SYSTEM LO BAT", accompanied by a once per minute "beeping" at the Keypad indicates that a low system battery condition exists. CALL FOR SERVICE IMMEDIATELY. A display of "LO BAT" and a zone descriptor, accompanied by a once per minute "beeping" at the Keypad indicates that a low battery condition exists in the wireless transmitter displayed. CALL FOR SERVICE IMMEDIATELY. A display of "MODEM COMM" indicates that the control is online with the central station's remote computer. The control will not operate while on-line. A display of HSENS and a zone number, indicates a smoke detector with a high sensitivity level, which may cause false alarms. CALL FOR SERVICE IMMEDIATELY. A display of LSENS and a zone number, indicates a smoke detector with a low sensitivity level. Detectors with a low sensitivity might not detect a smoke condition. CALL FOR SERVICE IMMEDIATELY.

a. ARM STAY OR INSTANT b. ZONE OPENED WHILE SYSTEM IS IN CHIME MODE. c. ENTRY WARNING**

-- 70 --

Glossary
The following terms are used throughout the manual. ARM/DISARM: Armed simply means that the burglary portion of your system is turned ON and is in a state of readiness. Disarmed means that the burglary system is turned OFF, and must be rearmed to become operational. However, even in a disarmed state, emergency and fire portions of your system are still operational. This is the area on your Keypad containing numbered pushbuttons similar to those on telephones or calculators. These keys control the arming or disarming of the system, and perform other functions which were previously described in this manual. A specific area of protection. An independent group of zones that can be armed and disarmed without affecting other zones or users. To disarm a specific area of burglary protection while leaving other areas operational. An area of protection containing doors most frequently used to enter or exit (typically, a front door, back door, or door from the garage into the building). The delay zone allows sufficient time for authorized entry or exit without causing an alarm. Consult your installer for the entry and exit delay times that have been set for your system during installation and record them on the separate sheet provided in this manual. An area of protection whose violation causes a trouble indication during the disarmed (DAY) mode and an alarm during the armed (NIGHT) mode.

KEYPAD:

ZONE: PARTITION: BYPASS: DELAY ZONE:

DAY/NIGHT ZONE:

-- 71 --
UL NOTICE: This is a GRADE A system.
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturers instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: If using an indoor antenna, have a quality outdoor antenna installed.

Plug the control/communicator into a different outlet so that it and the receiver are on different branch circuits. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user or installer may find the following booklet prepared by the Federal Communications Commission helpful: Interference Handbook This booklet is available from the U.S. Government Printing Office, Washington, DC 20402. The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or Users Manual. Unauthorized changes or modifications could void the users authority to operate the equipment. IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS In the event of telephone operational problems, disconnect the control by removing the plug from the RJ31X (CA38A in Canada) telephone wall jack. We recommend that your certified installer demonstrate disconnecting the phones on installation of the system. Do not disconnect the phone connection inside the control/communicator. Doing so will result in the loss of your phone lines. If the regular phone works correctly after the control/communicator has been disconnected from the phone lines, the control/communicator has a problem and should be returned for repair. If upon disconnection of the control/communicator, there is still a problem on the line, notify the telephone company that they have a problem and request prompt repair service. The user may not under any circumstances (in or out of warranty) attempt any service or repairs to the system. It must be returned to the factory or an authorized service agency for all repairs.
Reorient the receiving antenna until interference is reduced or eliminated. Move the receiver away from the control/communicator. Move the antenna leads away from any wire runs to the control/communicator.

-- 72 --

FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 NOTICE This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company. This equipment uses the following jacks: An RJ31X is used to connect this equipment to the telephone network. The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe necessary. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service. If trouble is experienced with this equipment, please contact the manufacturer for repair and warranty information. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved. There are no user serviceable components in this product, and all necessary repairs must be made by the manufacturer. Other repair methods may invalidate the FCC registration on this product. This equipment cannot be used on telephone company-provided coin service. Connection to Party Line Service is subject to state tariffs. This equipment is hearing-aid compatible. When programming or making test calls to an emergency number, briefly explain to the dispatcher the reason for the call. Perform such activities in the off-peak hours; such as early morning or late evening.

-- 75 --

WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM (continued)
Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers. Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments.

-- 76 --

#70 command..or 4286 VIP module..9, 43 AC Loss..61 Access Another Partition..22 Access Door..42 Add a User..18 ADD NEW USER..20 Add User Code..17 Ademco Dealer..61 Alarm..6 Alkaline batteries..66 Alpha Keypads..10 Armed..5 ARMED INDICATOR..13 Audible Emergency.39 Audible Signals..70 Authority Level..15 Authority Levels..16, 17 Away..5, 22 AWAY..36 AWAY Mode..33 Battery Life..66 Burglary...4 Burglary Protection..5 Bypass- Access Door..42 Bypass Zones...29 Bypassing...29 Call Service..59 Change a User's Code..20 Change User Code..17 CHECK..59 Chime..5, 37 Closing Time..45 Comm. Failure..60 Common Lobby..25 Delaying Closing Time..45 Delete a User.. 21 Delete User Code.. 17 Descriptors.. 28 Device Timers.. 7, 49 Disarm... 35 DOC.. 74 Duress... 16 Duress Code.. 15 Emergency... 4 Entry Delay.. 14 Entry/Exit.. 5 Event Log Procedures. 52 Exit Delay.. 14 Exit User Edit Mode.. 18 FCC.. 72 Fire.. 4, 39 Fire Alarm.. 56 Fire Display Lock.. 57 FIRE DRILL ACTIVE. 57 Fire Drill Test.. 57 Fire Protection.. 5 GLOBAL ARM.. 19 Global Arming.. 22 Glossary.. 71 Goto.. 19 GOTO.. 22 GOTO Command. 7 Grant- Access Door. 42 HSENS.. 60 Instant.. 5, 22 INSTANT... 14 INSTANT Mode. 32 Keypad.. 4 Keypad back lighting.. 10 Keypad Functions.. 12 Keypads.. 10