ADEMCO VISTA-48C

Security System

Programming Guide
This control complies with prEN50131-1:2004 and TS50131-3; Grade 2, Class II
K0749-3ENPRV1 5/06 Rev. A
FIRST STEP: SELECT THE LANGUAGE When programming the system, you should first select the appropriate language by doing the following: 1. Enter Programming mode. 2. Press [] + 28 (Language Select data field). 3. Press the number corresponding to the desired language: 0 = English, 1 = Russian, 2 = Hebrew , 3 = French 4. Continue programming the system as desired. TO START PROGRAM MODE, use method A or B (must use alpha keypad connected to keypad terminals): A. POWER UP, then press both [] and [#] at same time within 50 seconds of powering up. (if 98 was used to exit program mode, this is the only method that can be used to start program mode again) B. Initially, key: Installer Code (4 + 1 + 1 + 2) plus 8 + 0 + 0. INSTALLER ACCESS NOTE: Some installations may require that the Installer cannot access the system without the end users permission (EN50131-1 compliance). Use field *26, entry 2, to select this option. If selected (Installer code disabled), the system master or partition master must first enable the Installer code before it can be used. Once enabled, the Installer code remains active until any other user enters their code. To enable the Installer code: master code + [#] + 65
Data Field Programming Procedures
Task Go to a Data Field Entering Data Procedure Press [] + [Field Number], followed by the required entry. When the desired field number appears, simply make the required entry. When the last entry for a field is entered, the keypad beeps three times and automatically displays the next data field in sequence. If the number of digits that you need to enter in a data field is less than the maximum digits available (for example, the phone number fields *41, *42), enter the desired data, then press [] to end the entry. Press [#] + [Field Number]. Data will be displayed for that field number. No changes will be accepted in this mode. Press [] + [Field Number] + []. (Applies only to fields 40*43, *45, *94, and pager programming fields)
Review a Data Field Deleting an Entry
Menu Mode Programming (56, 57, 58, 79, 80, 81, 82, 83)
Press [] + [Interactive Mode No.] (for example, 56). The alpha keypad displays the first of a series of prompts. Interactive Mode Used to Program 56 Zone Programming Zone characteristics, report codes, alpha descriptors, and serial numbers for 5800 RF transmitters. 57 Function Key Programming Unlabeled keypad keys (known as ABCD keys) for special functions 58 Zone Programming Same options as *56 mode, but with fewer prompts. Intended for those familiar with (Expert mode) this type of programming, otherwise *56 mode is recommended. Assign module addresses and map individual relays/powerline carrier devices 79 Output Device Mapping 80 Output Programming 4229 or 4204 Relay modules, 6164 output relay, Powerline Carrier devices, or onboard triggers 81 Zone List Programming Zone Lists for relay/powerline carrier activation, chime zones, pager zones, etc. 82 Alpha Programming Zone alpha descriptors 83 Configurable Zone type Prog Attributes for configurable zone types INITIALIZE DOWNLOAD and RESET DEFAULTS 96 Initializes download ID and subscriber account number. 97 Sets all data fields to original factory default values. The control has two unique sets (tables) of default entries. Press 97 while in Program Mode, then press 1 or 2 to load the desired set of factory defaults. This resets all data fields to the respective default table values. Default values are listed next to the data field entry boxes on the Program Form with unique table 1 and table 2 values indicated where applicable (DT1 = default table 1; DT2 = default table 2). User Code Defaults: To reset only the user codes to default values, press 97, then press 3.

Test Restore Rpt Code Summer Time Start\End Month

[00] [3][10]

Primary Subscriber ID # (Part. 3)
Secondary Subscriber ID # (Part. 3)
| | | | | | | | | [0] [0]
Fields *51 and *52 see box above 43 for entries.
0 = Disabled; 1-12 = month (1 = January, 2 = February, etc) #+10 = October; #+11 = November; #+12 = December
Summer Time Start\End Weekend [5][5]
0 = disabled; 1 = first; 2 = second; 3 = third 4 = fourth; 5 = last; 6 = next to last; 7 = third to last

SESCOA / Radionics

0 = Radionics (0-9, B-F); 1 = SESCOA (0-9 reporting only)

Auto Stay Arm

0 = none; 1 = partition 1; 2 = partition 2; 4 = partition 3 Add the values for multiple partitions.

Dynamic Signaling Delay

Delay selectable from 0 to 225 secs in 15-sec increments. 0 = no delay (both signals sent); 1 = 15 secs; 2 = 30 secs, etc. UL/C-UL: Grade AA must be 0; Grade A must be 15 max
Linked Zone Verification Timer / Up and About Timer
Dynamic Signaling Priority
0 = Primary Dialer first; 1 = ECP Contact ID first (e.g., TCP-IP ethernet) For UL/C-UL Commercial Burglary installations that use a DACT and LRR, this field must be 0.
TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES:
For 3+1 or 4+1 Standard Format: Enter a code in the first box: 19, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F. A 0 (not #+10) in the first box will disable a report. A 0 (not #+10) in the second box will result in automatic advance to the next field. For Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 19, 0, or BF, as described above. A 0 (not #+10) in the second box will eliminate the expanded message for that report. A 0 (not #+10) in both boxes will disable the report. For Ademco Contact ID Reporting: Enter any digit (other than 0) in the first box, to enable zone to report (entries in the second boxes are ignored). A 0 (not #+10) in the first box disables the report. UL/C-UL: see installation instructions for requirements
Linked Up/about Linked Zone: Assign linked zones on zone list 4, with *81 Menu mode. 0 = 15 seconds 4 = 90 seconds 8 = 4 min #+12 = 8 min 1 = 30 seconds 5 = 2 minutes 9 = 5 min #+13 = 10 min 2 = 45 seconds 6 = 2-1/2 min #+10 = 6 min #+14 = 12 min 3 = 60 seconds 7 = 3 min #+11 = 7 min #+15 = 15 min Up and About Timer: 1-15 hours (also need to program up and about schedule for time window that up and about feature is active; value set in this field is time within the schedule that activity must occur)

0 = Basic RF supervision and RF jam detection 1 = Report RF supervision failure as tamper alarm when armed 2 = Report RF Jam as tamper alarm when armed 3 = Report RF Jam and RF supv failure as tamper alarm when armed

180 Zone Bypass Limit

0 = unlimited zone bypasses in each partition 1-7 = number of zone bypasses allowed in each partition (each partition individually uses this entry)
Ring Count For Downloading
0 = Disable Monitoring Station Initiated Download; 114 = number of rings (19, # +10 =10, # +11 =11, # +12 =12, # +13 =13, # +14 =14); 15 = Answering machine/fax defeat (# +15 =15).
181 50/60 Hertz AC Operation (for real-time clock) [5]
Use the following table to select the desired options for real-time clock synchronization (50Hz, 60Hz, Crystal), AC Loss display (independent of AC Loss report enabled in *62), and clock display (time displayed on bottom line of alpha keypads). X10 NOTE: X10 (powerline carrier devices) use the selected AC frequency to communicate with the control. UL: must be 0 Entry AC Freq. Crystal for AC Loss disp Clock disp 60Hz clock backup no no #+10 #+11 #+12 #+13 #+14 #+15 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz 50Hz 60Hz 50Hz clock backup clock clock clock backup clock backup clock clock clock backup clock backup clock clock clock backup clock backup clock clock no no no yes yes yes yes no no no no yes yes yes yes no no no no no no no yes yes yes yes yes yes yes yes

160 Pager 1 Phone No.

| | | | | | | | | | | | | | | | | | |
Enter up to 20 digits, 09; #+11 for ''; #+12 for '#'; #+13 for a 2second pause. Do not fill unused spaces. If fewer than 20 digits, exit field by pressing. To clear entries from field, press 160.

161 Pager 1 Characters

| | | | | | | | | | | | | | |
Enter the optional prefix characters, up to 16 digits. 09; #+11 = ''; #+12 = '#'; #+13 = 2-second pause.
162 Pager 1 Reporting Options
For each partition, select from: [0,0,0] Part. 1 Part. 2 Part = no reports sent; 1 = Open/close all users; 4 = All alarms and troubles 5 = All alarms / troubles, and open/closes for all users 12 = Alarms / troubles for zones entered in zone list = Alarms / troubles for zones entered in zone list 9, and opens/closes for all users
163 Pager 2 Phone No. (See field *160 for entries.)

0 = no; 1 = yes (partition number displays on alpha keypads)
189 AUI Device 1 and 2 Enable
(for Touch Screen Style Keypads)
0 = 3-digit display (1 + device address); for 6148, 6150,6160,= 2-digit fixed-display as 91; for 6128 series keypads
AUI 1 AU2 System supports up to two touch screen style keypads (e.g., Symphony Advanced User Interface, and 6270 Touch Screen Keypad). AUI Compatibility Note: To ensure proper AUI device operation, use AUI devices with the following rev levels: 6270 series use version 1.0.9 or higher; 8132/8142 (Symphony) series use version 1.1.175 or higher. Touch Screen (AUI) device 1: Must set AUI device address to 1 Touch Screen (AUI) device 2: Must set AUI device address to 2 Enter each AUIs home partition. 0 = disabled 1 = partition 1; 2 = partition 2; 3 = common partition
*56 ZONE PROGRAMMING WORKSHEET [default values shown in brackets]

Zone Zn Type Partition

[09] [01] [03] [03] [03] [03] [03] [03] [1] [1] [1] [1] [1] [1] [1] [1]

Report

Basic Wired Type Response Time
[EOL] [EOL] [EOL] [EOL] [EOL] [EOL] [EOL] [EOL] [1] [1] [1] [1] [1] [1] [1] [1]

Location

Zone Zn Type Partition NOTES: 37 Zone Type: see chart on 38 next page 39 Basic wired Type (zns 1-8): = EOL = NC = NO 3 = zone doubling (2-8) = double-balanced 44 (2-8) 45 Input Type: = AW (zones 9-48) = RF (zones 9-48) = UR (zones 9-48) 49 [1] 5 = BR (zones 49-64) 7 = RM (zones 9-48) 50 [1] NOTE: Zones 10-16 not 51 [1] available depending on 52 [1] whether zone doubling 53 [1] enabled on zones 2-8. 54 [1] Response Time: 55 [1] 0 = 10msec 56 [1] 1 = 400msec 2 = 700msec 57 [1] 3 = 1.2 sec 58 [1] NOTE: If zone doubling is 59 [1] selected, the response 60 [1] time selected for the basic 61 [1] zone automatically applies to the associated doubled 62 [1] zone. 63 [1] 64 [1] Reserved Zones 91 [05] N/A 91 = addressable device report enable/disable 92 N/A N/A default zone type = 95 [00] [05]. 96 [00] 92 = Duress report 99 [06] enable/disable

Input Type

Serial Number
[BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] [BR] N/A N/A N/A N/A N/A

N/A N/A N/A N/A N/A

Zn ZT P RC 1 10

In: L RF: 1

10 Zone Type Perimeter

10 Partition Report Code 1st 01 2nd 00

02 HARDWIRE TYPE EOL 0

02 Response Time INPUT TYPE RF TRANS 3
10 INPUT S/N: L A022-4064 1
For wireless transmitters, enroll the serial number and loop number as follows: 1. a. Transmit two open/close sequences. If using a button-type transmitter, press and release the button twice, but wait about 4 seconds before pressing the button the second time. OR b. Manually enter the 7-digit serial number printed on the label of the transmitter. Press the [] key to move to the L position, then enter the loop number. If desired, you can press the [C] key to copy the previously enrolled serial number (used when programming a transmitter with several input loops). The cursor moves to the loop number position. c. To delete an existing serial number, enter 0 in the loop number field. The serial number will change to 0's. If 0 was entered in error, simply re-enter the loop number or press [#], and the serial number will return to the display. 2. Press [] to continue. The system now checks for a duplicate serial/loop number combination.
10 INPUT S/N A022-4064 XMIT TO CONFIRM PRESS TO SKIP
If the serial/loop number combination is not a duplicate in the system, a display showing the serial number and loop number entry appears. [] to continue This prompt will only appear if you answered Yes at the first prompt in this section. The system will enter a confirmation mode so that the operation of the actual programmed input can be confirmed. Activate the loop input or button that corresponds to this zone. [] to continue If the serial/loop number transmitted does not match the serial number entered, a display showing the entered and the received serial/loop numbers appears. If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary display does not appear), press the [#] key twice and then enter (or transmit) the correct serial number. [] to continue If the serial number transmitted matches the serial number entered, the keypad will beep 3 times and a summary display will appear, showing that zone's programming. An s indicates that a transmitters serial number has been enrolled. [] to accept the zone information and continue If you want to program descriptors for zones now, enter 1 (Yes) and refer to the *82 Descriptor Programming section for procedures. To program descriptors later, enter 0 (no). [] to continue If 0 (No) was entered at the Program Alpha prompt, the system will return you to the ENTER ZN NUM. prompt for the next zone. When all zones have been programmed, enter 00 to quit.

Entd A022-Rcvd A022-4064 1

Zn ZT RC In: L 10 RF: 1s

PROGRAM ALPHA? 0 = NO 1 = YES 0 E N TE R Z N N U M. (00 = QUIT) 11
58 Expert Programming Mode Procedures (press 58 while in Data Programming mode)
SET TO CONFIRM? 0 = NO 1 = YES
Zn ZT P RC HW: RT EL = no 1 = yes (prompt appears after entering the serial and loop numbers to confirm each transmitter) We recommend that you confirm the programming of every transmitter. A summary screen will appear, showing zone 1s currently programmed values. Enter the zone number being programmed, then press []. In this example, zone 10 is being entered. 01-64 = zone number [D] = for assigning wireless key programming templates (see Wireless Key Programming Templates section in i/i); lets you choose from a series of preset templates for easy programming of wireless key zones 00 = quit (when all zones have been programmed, press 00 to quit this menu mode) [] to continue
Zn ZT P RC IN: L 10 : Zn ZT P RC IN: L RF 1
A summary screen with the selected zones current programming appears. Begin programming zone information as follows: Enter Zone Type (ZT; see Zone Type chart shown in *56 Menu Mode Zone Type prompt), Partition (P), Report Code (RC; 0-9 only; see *56 mode for hex codes), and Input Device Type (IN)* sequentially (Loop Number (L) is entered at the next prompt). Use the [A] (Advance) and [B] (Back) keys on the keypad to move the cursor within the screen. Use the [C] key to copy the previous zones attributes. * If HW (basic wired) or AW (Auxiliary) is entered for Input Device Type, the display will be similar to the prompt shown, except that HW or AW will be under IN. Press [] to save the programming and continue. If needed, press the [#] key to back up without saving. For wireless devices (input types RF, UR, BR, RM), continue to the serial number/loop number prompt. For wired devices, return to the initial summary screen prompt to begin programming the next zone.

10 INPUT S/N: AXXX-XXX

Zn ZT P RC In L RF: 1s
Manually enter the serial number (found on the transmitter label), by entering the digits in the X locations, using the [A] (advance) or [B] (back) keys as required. OR Transmit two open/close sequences. If using a button-type transmitter, press and release the button twice, but wait about 4 seconds before pressing the button the second time. If you want to copy the previous zones serial number, press the [C] key. Press [] to advance to the loop number, then enter loop number. Press [] to accept the existing serial and loop number and continue to the Confirm prompt described in *56 Menu mode above. If necessary, press [#] to back up and re-enter or edit the serial number. If the serial number transmitted matches the serial number entered, the keypad will beep 3 times and a summary display will appear, showing the programmed information for that zone. Press [] to begin programming the next zone. See first Summary Screen prompt paragraph on previous page.

Wireless Key Programming Templates (press the [D] key from *58 Menu mode Summary Screen display)
This procedure programs the wireless keys, but a key is not active until it is assigned to a user number (see System Operation section, assigning attributes command in the Installation Instructions).

TEMPLATE ? 16 L T 02 22

Enter desired template number 16 (see chart below). Press [#] if you want to return to *58 Menu mode Summary Screen. If necessary, press [#] to back up and re-enter template number. Press [] to continue to template display. When [] is pressed, the selected template will be displayed. Top line of display represents loop numbers, bottom line represents zone type assigned for each loop. Press [] to accept template and continue. Enter the partition in which the key is to be active. 1 = partition 1; 2 = partition 2; 3 = partition 3 (or common area partition) Press [] to continue. The system will search for the highest available consecutive 4-zone group (the four zones in the case of the 5804 and 5804BD/5804BDV), and display the lowest zone number of the group. If you want to start at a different zone, enter the zone desired, and press []. If that zone number is displayed, the system has the required number of consecutive zones available, beginning with the zone you entered. If not, the system will again display a suggested zone that can be used. If the required number of consecutive zones is not available at all, the system will display 00. Press [] to accept and continue. Manually enter the serial number printed on the label for the wireless key or press and release the button to transmit its serial number. Press [] to accept the serial number. The system will check for duplicate. If necessary, press the [#] key to back up without saving, and re-enter the serial number. Use the [A] key to move forward within the screen, and the [B] key to move backward. If Yes was entered at the SET TO CONFIRM? prompt (first prompt following entry into the 58 Expert Programming Mode), the display on the left will appear. Confirm serial and loop numbers by activating the wireless key. Refer to the Confirm prompt described in *56 Menu mode earlier for more information on confirming the serial number. If the serial number transmitted matches the serial number entered, the keypad will beep 3 times and will return you to the ENTER START ZONE NUMBER prompt to enter the starting zone for the next wireless key. IMPORTANT: When confirmed, the key is not active until it is assigned to a user number (using the assigning attributes command, attribute 4). See System Operation section in Installation Instructions. [] to skip confirm. Zone Type

*57 FUNCTION KEY PROGRAMMING
Option 00 Function P1 A P2 P3 P1 B P2 P3 P1 C P2 P3 P1 D P2 P3 Comments Paging Time Display Arm AWAY Arm STAY Arm NIGHT-STAY Step Arming Device Activation Device: Comm. Test Macro Key 1 Assign each macro key to only a single partition. Macro Key 2 Assign each macro key to only a single partition. Macro Key 3 Assign each macro key to only a single partition. Macro Key 4 Assign each macro key to only a single partition. Emergency Keys: zone 95 zone 99 zone 96 paging Personal Emergency n/a Silent Alarm n/a Audible Alarm n/a Fire n/a Emergency Keys: A = paired keys [1] / [] (zone 95); B = paired keys [] / [#] (zone 99); C = paired keys [3] / [#] (zone 96) There are only four macros system-wide.

INSTANT

Partition 1 Key "A" Func Zone 95 00
1 = function key active in partition = function key active in partition = function key active in partition 3 [] to continue Enter the desired function for this key: 00 = For the Function key selected, the function will be as follows (system default): If A selected = Zone 95 (emergency key, same as [1] [] pair) If B selected = Zone 99 (emergency key, same as [] [#] pair) If C selected = Zone 96 (emergency key, same as [3] [#] pair) If D selected = Single-button paging 01 = Single-button paging (sends a 999-9999 message to pager) 02 = Display time 03 = Arm AWAY (reports as User 00 if closing reports are enabled) 04 = Arm STAY (reports as User 00 if closing reports are enabled) 05 = Arm NIGHT-STAY (reports as User 00 if closing reports enabled) 06 = Step Arming (arms STAY, then NIGHT-STAY, then AWAY) 07 = Output Device Command (for device programmed as system operation type 66 in *80 Menu Mode) 08 = Communication Test (sends Contact ID code 601) 09 -12= Macro Keys 1-4 respectively (defined by [#] [6] [6] command) [] to continue; returns to key number prompt with the next function key letter displayed.

keypad_keys-00-001-V0

Start Function Key Programming mode by pressing 57 while in Data Programming mode. Press the desired function key, A-D. Press Key to Pgm NOTE: A key programmed as a function key is no longer available to be used for any other function. 0 = Quit 0 [] to continue

BYPASS

For keypad activated devices, use *79 Menu mode to assign a system output number and associate its corresponding device. For automatic activation, use *79 Menu mode as above, and use *80 Menu mode to define the system condition that will activate/deactivate the device(s).
OUTPUT RELAYS/POWERLINE CARRIER DEVICES WORKSHEET FOR 79, 80 and 81.
79 RELAY/POWERLINE CARRIER DEVICE MAPPING (Must program before using *80)
OUTPUT TYPE Relay X10 Output Module Pos Unit Description No. Addr. (1-4) No. To Activate/Deactivate Devices in Normal Operating Mode:

Code + # + 7 + NN Key Entry starts Device NN. Code + # + 8 + NN Key Entry stops Device NN.
OUTPUT TYPE Relay X10 Output Module Pos Unit No. Addr. (1-4) No. 17 On-Board Trigger On-Board Trigger 2

Description

Postive\Negative Trigger Postive\Negative Trigger
Start Output Device Mapping by pressing *79 while in Data Programming Mode. Enter the logical (or reference) relay number as used in the system. ENTER OUTPUT NO. 01-16 = relays/X-= QUIT xx 17-18 = on-board triggers (can be programmed for inverted output; see next prompt) [] to continue 17 OUT NORM LOW 0 = NO 1 = YES 0 This prompt appears only for triggers 17 and 18. 0 = no (standard default); sets the trigger output level normally high 1 = yes; sets the trigger output normally low (can be used for resetting 4-wire smoke detectors by connecting trigger wire to the negative power terminal of the smoke detector, selecting 1 at this prompt, and setting as zone type 54, fire zone reset, in *80 Menu mode) [] to return to Output Number prompt Select whether this is a relay or a Powerline Carrier (X-10) device. 0 = delete this output number 1 = relay on 4204/4229 module, 6164 keypad (skip to B prompt) 2 = Powerline Carrier device (go to A prompt) [] to continue Enter the devices unit code (set at the device) 01-16 = predefined address [] to returns to the Output Number prompt Enter the modules predefined address (set the modules DIP switches to the selected address, or key the 6164 address) 07-15 = predefined address (see table of device addresses) [] to continue Enter the actual (or physical) relay number with respect to the Relay Module upon which it is located. For 4204 modules, relay numbers are 1-4. For 4229 modules, relay numbers are 1-2. For 6164 keypad, relay number is 1. 1-4 = relay position [] to return to the Output Number prompt for programming the next device

XX OUTPUT TYPE DELETE? 0

A XX UNIT No. yy B XX MODULE ADDR 07-15 yy

XX REL POSITION 1-4 zz

OUTPUT DEFINITIONS
NOTES: 1. For Relays, 4229, 4204, and 6164 devices are programmed in *79, *80, and *81 modes. 2. For Powerline Carrier devices, field 27 must be programmed with a House Code. 3. Tampers of expansion units cannot be used to operate devices.
Zone Types: 00 = Not used 01 = Entry/exit #= Entry/exit #= Perimeter 04 = Interior Follower 05 = Trouble Day/Alarm Night 06 = 24-Hr Silent Choices for System Operation are: 20 = ArmingStay 21 = ArmingAway 22 = Disarming (Code + OFF) 31 = End of Exit Time 32 = Start of Entry Time 33 = Any Burglary Alarm 36 = **At Siren Timeout***
07 = 24-Hr Audible 08 = 24-Hr Aux 09 = Fire 10 = Interior w/Delay 12 = Monitor Zone 14 = Gas 16 = Fire w/Verify 20 = ArmSTAY* 38 = Chime 39 = Any Fire Alarm 40 = Bypassing 41 = **AC Mains Failure 42 = **System Battery Low 43 = Communication Failure 52 = Kiss off 54 = Fire Zone Reset

01 Enter Zn Num. (00 = Quit) 00
01 Del Zn List? 0 = No 1 = Yes 0
01 Delete Zone? 0 = No 1 = Yes 01 Zn to Delete? (00 = Quit) 00 0

DESCRIPTOR PROGRAMMING

The Program Alpha ? prompt appears. 1 = program zone descriptors, partition descriptors 0 = exit [] to continue This prompt selects whether you are entering zone descriptors or entering partition descriptors. 0 = create zone descriptors (see Zone No? prompt below) 1 = create partition descriptors [] to continue If 1 selected, the following prompt appears. Enter the 2-digit custom word number (11-13) to be programmed, then press []. PART? = partition 1 descriptor; 12 = partition 2 descriptor; 13 = partition 3 descriptor Enter the descriptor as described in steps 1-3 in the Zone Number section below. Enter the zone number for the descriptor you are programming. Press [] to continue. A cursor appears at the beginning of the second line. Special Keys: [6] = accept character and move cursor to next position to right [4] = move cursor to left [8] = save descriptor 1. Refer to the Character Chart on the next page. Press [#], followed by the 3-digit entry for the first letter you want to display (e.g., # 5 for A). Press [6] to move the cursor to the right, in position for the next character. 2. Repeat Step 1 to enter the next characters until the desired descriptor is entered. You can use the [4] key to move the cursor to the left, if necessary. Zone descriptors can be a maximum of 16 characters. Partition descriptors can be a maximum of 10 characters. 3. When done, press the [8] key to save the descriptor and return to the Zone No. ? prompt. To enter a descriptor for the next zone, 4. Enter the zone number for the next descriptor, press [], and repeat steps 1-3. To change a descriptor, simply overwrite it. To exit, enter zone number 00.
Start Zone Descriptor Programming mode by pressing *82 while in Data Programming mode.
Program Alpha ? 0=No, 1=Yes 00 Sel Zone Des=0 Part = 1

Zone No.?

CHARACTER (ASCII) CHART (For Creating Zone/Partition Descriptors)
032(space) 033 = ! 034 = " 035 = # 036 = $ 037 = % 038 = & 039 = ' 040 = ( 041 = ) 042 = * 043 = + 044 = , 045 = 046 =. 047 = / 048 = = 050 = 051 = 052 = 053 = 054 = 055 = 056 = 057 = 058 = 059 = 060 = 061 = 062 = 063 = 064 = 065 = 9 : ; < = > ? @ A 066 = 067 = 068 = 069 = 070 = 071 = 072 = 073 = 074 = 075 = 076 = 077 = 078 = 079 = 080 = 081 = 082 = B C D E F G H I J K L M N O P Q R 083 = 084 = 085 = 086 = 087 = 088 = 089 = 090 = 091 = 092 = 093 = 094 = 095 = 096 = 097 = 098 = 099 = S T U V W X Y Z [ ] ^ _ ` a b c 100 = 101 = 102 = 103 = 104 = 105 = 106 = 107 = 108 = 109 = 110 = 111 = 112 = 113 = 114 = 115 = 116 = d e f g h i j k l m n o p q r s t 117 = 118 = 119 = 120 = 121 = 122 = 123 = 124 = 125 = 126 = 127 = 128 = 129 = 130 = 131 = 132 = 133 = u v w x y z { | } 134 = 135 = 136 = 137 = 138 = 139 = 140 = 141 = 142 = 143 = 146 = 152 = 155 = 156 = 157 = 160 = 161 = 162 = 163 = 164 = 165 = 166 = 167 = 168 = 169 = 170 = 171 = 172 = 173 = 174 = 175 = 176 = 177 = 178 = 179 = 180 = 181 = 182 = 183 = 184 = 185 = 186 =

ENTER EVENT

NOTE: Event 07 causes the keypad to beep every 30 seconds when messages are displayed. Stop the beeps by user code + OFF.

DEVICE NUMBER XX

GROUP NUMBER X PARTITION X START SMTW TFS
This prompt appears if event 2 (user access) was selected. Otherwise it is skipped. 1-8 = group number [] to continue to the Start prompt. This prompt appears if events 3-7, or 10 were selected. Otherwise it is skipped. 0 = all partitions; 1 = partition 1; 2 = partition 2; 3 = partition 3 [] to continue Enter the events start time and days of the week to occur. To select days, position the cursor under the desired days using the [] key to move forward, then press 1 to select the day. 01-12 (00-23) = hour (use 00-23 if 24-hour time is enabled) 00-59 = minute; 0 = AM; 1 = PM Days = place 1 under days [] to continue This prompt appears if events 4 or 5 were selected. Enter the desired amount of time the system should warn of impending arming. The system will beep once every 30 seconds to alert users that arming will soon occur. Otherwise, this prompt is skipped. 01-15 = minutes of arm warning delay time [] to continue Enter the events stop time and days of the week to occur. To select days, position the cursor under the desired days using the [] key to move forward, then press 1 to select the day. This entry applies only to the following events: 1 (relay on/off); 2 (user access); 3 (child-not-home report) 01-12 (00-23) = hour (use 00-23 if 24-hour time is enabled) 00-59 = minute; 0 = AM; 1 = PM Days = place 1 under days [] to continue Enter the desired repeat option for this schedule. e.g., To make a schedule that happens everyday you would select all days with a repeat count of 1. To make a schedule that runs for one week then stops, select everyday with a repeat count of 0. 0 = do not repeat 1 = repeat schedule weekly 2 = repeat schedule biweekly (every other week) 3 = repeat schedule every third week 4 = repeat schedule every fourth week [] to continue If selected, the scheduled start and stop times will vary within 60 minutes of the hour time. For example, if a schedule is set to start at 6:15pm, it will do so the first time 6:15pm arrives, but on subsequent days it will start anytime between 6:00 and 6:59 p.m. NOTE: Do not use the random option if the start and stop times are within the same hour setting, otherwise unpredictable results may occur (e.g., the randomized stop time may occur before the start time). 0 = no; 1 = yes [] to continue

HH MMA M 0

W ARNING DLY TIME

SMTW TFS

REPEAT OPTION

RANDOMIZE

0=NO 1=YES X

NOTES

WARNING THE LIMITATIONS OF THIS ALARM SYSTEM
While this System is an advanced design security system, it does not offer guaranteed protection against burglary, fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example: Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery-operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. A user may not be able to reach a panic or emergency button quickly enough. While smoke detectors have played a key role in reducing residential fire deaths, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire. Finally, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending on the nature of the fire and/or location of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death. Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of the protected area approaches the temperature range of 32 to 40C, the detection performance can decrease. Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices are located on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people. Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. The security keypad (and remote keypad) should be tested as well. Wireless transmitters (used in some systems) are designed to provide long battery life under normal operating conditions. Longevity of batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device being used. External factors such as humidity, high or low temperatures, as well as large swings in temperature, may all reduce the actual battery life in a given installation. This wireless system, however, can identify a true low-battery situation, thus allowing time to arrange a change of battery to maintain protection for that given point within the system. Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments.

HEAT DETECTOR

USE UL LISTED LIMITED ENERGY CABLE FOR ALL CONNECTIONS
RING TIP RING TIP (BROWN) (GRAY) (GREEN) (RED)
CLASS 2 PLUG-IN 110VAC TRANSFORMER 16.5VAC, 25VA (e.g. ADEMCO No. 1321CN) OR WIRED-IN 16.5VAC, 25VA 220VAC TRANSFORMER TO 110/220VAC UNSWITCHED OUTLET (24HR)

HANDSET

INCOMING PHONE LINE TELEPHONE WIRING (VIA RJ31X* JACK AND DIRECT CONNECT CORD) *CA38A IN CANADA
FOR UL INSTALLATIONS, 110 VAC TRANSFORMER MUST BE USED
EARTH GROUND SEE INSTRUCTIONS FOR PROPER GROUNDING

DOC LOAD NO.: 3

WARNING: TO
2000 OHMS EOLR 2000 OHMS EOLR 2000 OHMS EOLR 2000 OHMS EOLR 2000 OHMS EOLR 2000 OHMS EOLR
PREVENT RISK OF SHOCK, DISCONNECT TELEPHONE LINE AT TELECOM JACK BEFORE SERVICING THIS UNIT.
THIS EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION'S STANDARD 72, CHAPTER 2 (NATIONAL FIRE PROTECTION ASSOCIATION, BATTERY-MARCH PARK, QUINCY,MA 02269). PRINTED INFORMATION DESCRIBING PROPER INSTALLATION, OPERATION,TESTING, MAINTENANCE, EVACUATION PLANNING AND REPAIR SERVICE IS TO BE PROVIDED WITH THIS EQUIPMENT.
MAXIMUM LOOP RESISTANCE: (EACH ZONE) 300 OHMS (PLUS EOLR) RESPONSE, ZONES 1-8: 10, 350, OR 700 MSEC (PROGRAMMABLE) MAXIMUM NUMBER OF 2-WIRE SMOKE DETECTORS ON ZONE 1 IS 16; DETECTORS MUST HAVE COMPATIBILITY IDENTIFIER AS "A".

TAMPER CONTACTS

ALARM OUTPUT 10.513.8VDC, 2A MAX. (600mA MAX. FOR UL USAGE, INCLUDING AUX POWER) STEADY FOR BURGLARY/PANIC, TEMPORAL PULSE SOUNDING FOR FIRE. CAN USE ADEMCO No. 702 SIREN, OR 12V BELL). SEE INSTRUCTIONS.

ZONE PAIRS

10 ZONE 2 2k
REMOTE KEYPADS AND OTHER ADDRESSABLE DEVICES (e.g. LRR, 4204, 4219, 4229, 5800TM, 5881EN, 7845i)
POWER SHUTDOWN NOTE: SYSTEM SHUTS DOWN SENSOR DETECTION PROCESSING IF CONTROL'S VOLTAGE DROPS BELOW 9.6V.

3k ZONE 10

CONNECTION OF THE FIRE ALARM SIGNAL TO A FIRE ALARM HEADQUARTERS OR A CENTRAL STATION SHALL BE PERMITTED ONLY WITH THE PERMISSION OF THE LOCAL AUTHORITY HAVING JURISDICTION. THE BURGLAR ALARM SIGNAL SHALL NOT BE CONNECTED TO A POLICE EMERGENCY NUMBER.
NOTE: KEYPAD (S) CURRENT (IN ALL PARTITIONS) AND ALL OTHER DEVICES DRAWING POWER FROM TERMS 4 & 5 MUST BE INCLUDED IN AUX CURRENT DRAIN CALCULATIONS.
REMOTE KEYPADS CAN USE 6148, 6150, 6150RF, 6160V, OR 6164 KEYPADS. (FIRST KEYPAD MUST BE SET TO ADDRESS 16.)

2 / / / / / / / 16

WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM. IN ADDITION, THIS SYSTEM MUST BE CHECKED BY A QUALIFIED TECHNICIAN AT LEAST ONCE EVERY THREE (3) YEARS.

2k ZONE 3

2k ZONE 4
TYPICAL WIRING FOR DOUBLE BALANCED ZONE (CAN ONLY BE USED ON ZONES 2-8)
TYPICAL WIRING FOR ZONE DOUBLING (CAN ONLY BE USED ON ZONES 2-8)

ALL DEVICES AND ACCESSORIES USED IN A CANADIAN INSTALLATION MUST BE LISTED FOR USE IN CANADA
VISTA-48C SUMMARY OF CONNECTIONS

VISTA-48C-SOC-V0