T E C H N I C A L

S P E C I F I C A T I O N S

BASE MODULE

The Advantage Plus Base Module is the primary communication processor and control unit for Advantage plus systems. Installed within the protected facilities, it is available in a standard UL version, attack rated enclosure version, or a military J-SIIDS version. It interfaces with all other optional modules and devices, and provides communication with the Advantor integrated monitoring system which will receive and display all security messages from the facility. It also includes the capability for listen back audio verification for up to four audio inputs.

DIMENSIONS

STANDARD UL ENCLOSURE
17.25 W x 14.5 H x 3.25 D (43.82cm x 36.83cm x 8.26cm) 20-gauge cold rolled steel with lock and key Color: Light gray w/ Advantor logo

AVR PLUS BAS-C shown

ATTACK-RATED UL ENCLOSURE
17.25 W x 14.5 H x 3.25 D (43.82cm x 36.83cm x 8.26cm) 18-gauge cold rolled steel with lock and key Color: Light gray w/ Advantor logo

TRANSMISSION MEDIA

DEDICATED
UL Grade AA Supervision for Compromise, and Failure

PCB FOOT PRINT

8.5" W x 7.54" H (21.59cm x 19.15cm)
Pulse or DTMF dialing Integrated cut line supervision RJ31X jack connection Secondary dial line capability with optional TelPlus Module Secondary cellular communication with optional Cellular Module Optional Telco Ditek Surge Protection

J-SIIDS COMPATIBILITY

Direct replacement for current J-SIIDS applications PCB is a replacement for the current transmitter and processor in conversions

ALARM POINTS

16 programmable, supervised, hard-wired points N/C, N/O, or both (dry contacts) Programmable alarm codes Assignable to any of 8 separate arming partitions (protected areas) All alarm points operate normally under ground fault conditions Expandable to a total of 144 points with Expansion Modules and an additional 63 points with the Wireless Module
SECOND LINE (OPTIONAL MODULE)
The TelPlus Module adds a second communication channel, either a dial with line supervision, or a dedicated line for dual line capability to meet NFBA72 4-2.3-2.1.6 or DTMF dialing PCB Foot print is 2.625" W x 2.125" H (6.67cm x 5.40cm) Power Requirements is 12 Volts DC (from Base Module) at 0 ma in Normal Standby mode and 45 ma in transmit mode Connects to the J9 connector on the Base Module

LOCAL ANNUNCIATION

Local bell drive: 12V at 1.25 Amp maximum Audible keypad beeper
ARM/DISARM FUNCTION (Secure/Access)
Up to 16 keypads 8 partition capability Programmable switch arming via momentary contact closure Programmable access card arming via integrated card reader input (wiegand) Programmable arm/disarm functions Single key arming Non-reporting Reporting by user Arm at shift Optional SCIF package 0 F to 122 F (-18 C to 50 C)
Four balanced audio inputs supporting four verification audio sensors or any combination of up to eight optional SmartAudio or ListenIn Modules for up to 128 audio inputs.

WIEGAND INPUT

Interfaces with one card reader or biometric device for secure, userfriendly arm/ disarm of security and access control verification for up to 100 users. Access Modules may be added to the system to extend the capabilities to up to 10,000 users.

OPERATING ENVIRONMENT

T E C H N I C A L S P E C I F I C A T I O N S

AUXILIARY OUTPUTS

Four, 100mA, programmable hard-wired Expandable to 36 total with Loop Expansion Modules

AVRPLUSBASCELKT

PRIMARY POWER OPTIONS
100 to 120 VAC, 60Hz, using 16.5 VAC, 50VA, Class 2 plug-in transformer 100 to 120 VAC, 50- 60Hz with internal transformer 200 to 240 VAC, 50-60Hz with internal transformer Can utilize existing J-SIIDS Power Supply Ditek AC Surge Protection
RUS PLUS BAS220 RUSPLUSBAS220AT AVR PLUS 90225102 90225192

SECONDARY POWER

12VDC, 7AH, sealed lead-acid rechargeable batteries (1 or 2, depending on top assembly P/N) Internal battery charger Backup capabilities 12 to 24 hours typical (depending upon installed equipment) Integral battery supervision for AC power loss, low battery and battery trouble
Factory integrated Base Module and Cellular Module, assembled in attack enclosure, with 120 VAC internal transformer. Includes Ditek AC surge and dial phone line surge protection Complete Base Kit, Russian Firmware, Standard enclosure, internal transformer, 20VAC, Ditek AC and telco dedicated line surge protection Complete Base Kit, Russian Firmware, Attack enclosure, internal transformer, 220VAC, Ditek AC and telco dedicated line surge protection Complete Base Kit, Standard enclosure with SmartAudio module, wall-mount transformer, 120VAC PCB, Base Module, UL PCB, Base Module with Russian Firmware Standard Enclosure, Advantor logo with Lock & Key Attack Enclosure, Advantor logo with Lock and Key Standard Enclosure, Advantor logo with Lock & Key and tamper switch Standard Enclosure, Chassis mounted transformer, with Ditek AC Surge Protection Attack Enclosure, Chassis mounted transformer, 220v with Ditek AC Surge Protection Installation Connector Kit JSIIDS Installation Connector Kit Transformer, 16.5VAC, 50VA, Plug-In Ditek AC Surge Protector (120VAC) hardwired Ditek AC Surge Protector (220VAC) hardwired Ditek Telco Dedicated Line Surge Protector, hardwired Ditek Telco Dial Line Surge Protector, hardwired Ditek AC Surge Protection for plug-in transformer LCD Keypad with Advantor Logo LCD Keypad with Advantor Logo, Cyrillic version Base Module Installation Instructions Base Module Installation Instructions, Russian JSIIDS to Advantage Plus Installation Instructions SCIF/Base Firmware Upgrade Instructions Enclosure Tamper Switch Kit Battery, 12V, 7 AH, Gel Cell TelPlus Module Complete with Installation Kit PCB, TEL PLUS Module TelPlus Module Installation Instructions

ENCLOSURES

ACCESS 4-A ENCL AVR CHAS/SUR115 AVRACHAS/SUR220

AUXILIARY POWER

1.6 Amps continuous at 12VDC (plug-in transformer) 1.3 Amps continuous at 12VDC (internal transformer) 1.0 Amps continuous at 12VDC (JSIIDS power supply)

COMMUNICATIONS

CENTRAL STATION 300 Baud asynchronous, full duplex Secure Protocol Communication Transmit: 1070/1270 Hz/Receive: 2025/2225 Hz, FSK BASE MODULE RS-485 PORT Communication link: 2,000 feet maximum using 22AWG, shielded twisted pair cable Supports a maximum of 40 RS-485 devices, to include: 16 total keypads 8 Expansion Modules 8 SmartAudio or ListenIn Modules in any combination 1 Wireless Module 7 Access Modules

ACCESSORIES

LCD PLUS AVR LCD PLUS AVR-RU TELPLUS 90227101 09820454

APPROVALS

FCC Part 15, Class B UL 294, Access Control System Units (with optional Access Module) UL 365, Police Connected Burglary UL609, Local Burglary UL 864, Control Units for Fire Protective Signaling Service UL985, Household Fire Warning System Units UL1023, Household Burglar-Alarm Systems UL 1076, Proprietary Burglar Alarm Units and Systems UL 1610, Central Station Burglar Alarm Units Communicator for UL 611, Central Station Burglary CSFM (California State Fire Marshal) ULC Commercial Fire and Burglary
Specifications and part numbers are subject to change without notice.

PART NUMBERS

MODULES/PCB'S AVR PLUS BAS AVR PLUS BAS DG AVR PLUS BAS-C AVR PLUS BAS220 AVRPLUSBAS220AT AVR PLUS BAS-J Complete Base Kit, Standard enclosure, wall-mount transformer Complete Base Kit, Standard enclosure, wall-mount transformer with modem communication firmware Complete Base Kit, standard enclosure, internal transformer, 120VAC, Ditek AC and telco dedicated line surge protection Complete Base Kit, Standard enclosure, internal transformer, 220VAC, Ditek AC and telco dedicated line surge protection Complete Base Kit, Attack enclosure, internal transformer, 220VAC, Ditek AC and telco dedicated line surge protection JSIIDS Upgrade Kit, with Ditek AC and telco dedicated line surge protection
6101 Lake Ellenor Drive Orlando, FL 32809 PH 1-800-ADVANTOR 407-859-3350 FX 407-859-5205 sales@advantor.com
w w w. a d v a n t o r. c o m
P/N 09820481, REV B, 12/00

T E C H N I C A L

S P E C I F I C A T I O N S

LISTEN-IN MODULE

The Listen-In Module gives the Advantage Plus Base Module the ability to support up to 16 audio verification sensors in any of eight partitions (Advantage AudioSensor or Advantage GlassBreak). Each Base Module can interface and control up to eight Listen-In or SmartAudio Modules.

DIMENSIONS

PCB FOOT PRINT
6.87" W x 4.125" H (17.45cm x 10.48cm)

PART NUMBERS

MODULES/PCB'S
ADV LIM APS12V1A-S 90231101 Listen-In Module with Installation Kit Power Supply, 12VDC PCB, Listen-In Module
16 audio sensor inputs Audio sensor pairs assignable to eight separate arming partitions (protected areas) Balanced audio output to Base Module

ENCLOSURES

Standard Enclosure, Advantor logo with Lock & Key 90258200 Attack Enclosure, Advantor logo with Lock and Key ACCESS 4-A ENCL Standard Enclosure, Advantor logo with Lock & Key and tamper switch AVR CHAS/SUR115 Standard Enclosure, Chassis mounted transformer, with Ditek AC Surge Protection AVRACHAS/SUR220 Attack Enclosure, Chassis mounted transformer, 220v with Ditek AC Surge Protection 90237200

OPERATING ENVIRONMENT

0 F to 122 F (-18 C to 50 C)

POWER REQUIREMENTS

12 VDC (from Base Module or optional APS12V1A-S Advantage Power Source) 30mA in both Normal Standby and Alarm

COMMUNICATIONS

Base Module RS-485 Communication link up to 2,000 feet maximum with 22AWG shielded twisted pair cable

ACCESSORIES

09820455 Transformer, 16.5VAC, 50VA, Plug-In Ditek AC Surge Protector (120VAC) hardwired Ditek AC Surge Protector (220VAC) hardwired Enclosure Tamper Switch ListenIn Module Installation

MOUNTING

One (1) mounts locally inside Base Module enclosure or remotely inside optional enclosure up to 2,000 feet from Base Module
Specifications and part numbers are subject to change without notice.
6101 Lake Ellenor Drive Orlando, FL 32809 PH 1-800-ADVANTOR 407-859-3350 FX 407-859-5205 sales@advantor.com
w w w. a d v a n t o r. c o m
P/N 09820487, REV B, 12/00