Dishwashers

AEG-Electrolux dishwashers deliver state-of-the-art performance with no compromise on the result, irrespective of the load, while maintaining stunning individuality in design. Millions of households have experienced the pleasure and convenience of AEG-Electrolux appliances as they give the best results in terms of cleanliness, shine, dryness, time and noise levels.

Functions & Features

Automatic Program A sensor in the dishwasher determines the amount of water, temperature and the cycle length based on the cloudiness or dirt content detected in the water. This program works in conjunction with the water sensing program. Water Sensing During the automatic program, the amount of soiling on the dishes is determined by the degree of clouding in the water via a light sensing system. During the varying wash cycles adjustments are made to the program duration, water and energy consumption to give you the optimum wash result. Self-Cleaning Filter The filter system progressively cleans the water as it circulates, trapping even the smallest food particles in the micro filter. The lower spray arm directs a jet of water which aids in self-cleaning the complete filter assembly. Automatic Load Adjustment The advanced fuzzy logic intelligence keeps water, electricity and detergent to an absolute minimum. The sensor logic calculates the optimum program required for the load, adjusting water and electricity accordingly. This load sensing system is able to detect only a few dishes in the upper or lower rack. The machine adjusts the amount of water and the duration of the wash program to the number of dishes. This means it is possible to wash only a few dishes quickly and economically. At half load (6 place settings), up to 3 litres of water and 0.4kWh electricity is saved.
30 Minute Program This program is designed to clean either just-used or average to lightly soiled dishes without pans. This short 60C program uses only 9 litres of water which is achieved by reducing the main wash time, the number of rinses to one and the drying time. Multi Tab / 3 in 1 This optimises the cleaning result in 3-in-1, 4-in-1 and 5-in-1 detergents by modifying the time and temperature of each phase of the program. This ensures that the different elements of the detergent are used in the correct part of the cycle for a perfect fresh result.
Program Completion Indicator Selected models feature a program completion signal which is an acoustic tone that sounds for 15 seconds. This tone can be deactivated if required. 5 Spray Levels For optimum wash results, the softer spray pressure in the top basket makes it ideal for fragile items, leaving the more vigorous spray action in the lower basket for heavily soiled items. All AEG-Electrolux dishwashers have longer spray arms to give a wider and improved water dispersion.
Aqua Alarm Selected models also feature an audible alarm warning you if the system becomes activated. Active Drying Residual drying with the added benefit of a condenser unit providing faster, more effective drying.
Anti-Flood System For complete peace of mind, AEG-Electrolux dishwashers have an Aqua-lock which switches off water supply to the dishwasher in the event of an accidental leak. This system will activate in stand-by mode providing the dishwasher is connected to a power supply.
Turbo Drying Selected models feature the turbo condenser drying system resulting in completely dry dishes every time. It activates a fan which draws steam from the dishwasher cabinet, condensing the steam back into water.
LED Display Allows you to scroll through the menu indicating programs, times and options available. Counts down the pre-set delay time then displays program phase and time to completion. Also indicates when salt and rinse aid need refilling. Electronic Display The electronic display indicates the time remaining to complete the wash and also the progression of the cycle. As the programs are selected, the display will indicate the approximate wash time. When the fuzzy logic takes control of the wash, the time display will adjust accordingly, reducing the wash time. Delay Start A delayed start of 1-19 hours can be selected in advance depending on the model. This convenient feature allows the dishes to be completed at night while you are sleeping. Fuzzy Logic Fuzzy logic will automatically lock out any incorrect selections and prevent any mistakes during a cycle. It will monitor the wash and make any adjustments to the wash time and water usage as required. Electronic Fault Display All AEG-Electrolux dishwashers feature an electronic fault display. In the event of an error during the program, a code will be displayed to tell you what has occurred. Your instruction book will advise on an appropriate course of action to remedy the problem. Water Softener System The water softener is adjustable to allow for variations in the level of hardness of the water. It also prevents deposits of scale forming when water has high lime content. A warning light appears when the special salt requires refilling.

Fold Down Plate Supports The plate supports in the lower basket fold down flat to fit large pots and trays
Counter-Balanced Door All AEG-Electrolux freestanding dishwashers have a counter-balanced door with a gentle opening and closing action. The door brake allows it to safely remain at any angle.
Wine Glass Supports Fold-away cup racks, when raised, create extra space and when lowered, support long stem glasses to prevent damage. Some glass stem diameters will clip in to the rack for total support.
Easily Accessible Basket The top and lower baskets can be pulled out completely clear of the dishwasher. This makes the baskets easier and quicker to load and also allows easy access to the filters and salt container. Plate Height / Adjustable Top Basket Depending whether raised or lowered, the top basket accommodates plates from 22 to 24cm. The direct injection system enables effective washing of oven trays or large platters. When fully loaded this basket can be adjusted to allow plates with a diameter from 29 to 30cm to be washed in the bottom basket.
Fold Out Cutlery Basket The convenient fold out design of the large cutlery basket makes it easier and more hygienic to unload. Flow Through Heater The flow through heater is a tubular element integrated into the water circuit on all models. Water gradually circulates through the tube creating a more precise temperature. Benefits include a smooth inner tub and plastic items will not melt or burn if they fall to the base. Pulse Wash System The pulse wash system in all AEGElectrolux dishwashers alternates a low spray pressure for 4 seconds, then high pressure for 1 second. Pulsating the water over the plates aids removal of any heavy soilage.
Standard Features: 12 place settings Extra wash options: Multi tab and delay start Water sensing system Flow through water heater Advanced fuzzy logic Auto load adjustment Anti-flood system 5 spray levels and 4 stage filter system Height adjustable upper basket Foldable cup supports upper Fold down plate supports lower Adjustable rinse aid dispenser and water softener Cold only water connection
NB: Features may vary depending on model. Please refer to product specifications.

Dishwasher Types

Built-under dishwashers AEG-Electrolux built-under dishwashers are designed with a full anti-fingerprint stainless steel door and handle, with the controls discreetly mounted on the top of the door for seamless integration. Fully integrated dishwashers Fully integrated dishwashers are designed to be totally hidden within the kitchen cabinetry. The touch controls are visible once the door is opened and are positioned on the top edge of the dishwasher door. Semi integrated dishwashers Semi integrated dishwashers are designed to build-in and match your kitchen cabinetry with only the control panel visible. The door panel and kick plate are not supplied as standard. Alternatively, an optional metal door in stainless steel can be fitted, as well as an optional stainless steel kick plate.

F60850VIM

60cm Built-under Dishwasher

F86070VI

60cm Fully Integrated Dishwasher

F88080IM

60cm Semi Integrated Dishwasher
12 place settings Anti-fingerprint stainless steel door 6 wash programs: Bio 50 with pre-rinse Automatic 50 - mins 60 Glass 45 Intensive care 70 Rinse and hold Extra wash options: Multi tab / 3 in 1 Delay start 1-19 hours Acoustic tone at end Program completion indicator Active drying Water sensing system Flow through water heater Advanced fuzzy logic Auto load adjustment Anti-flood system Aqua alarm 5 spray levels 4 stage filter system Height adjustable upper basket Foldable cup supports upper Fold down wine glass rack upper Fold down dividable rack upper Fold down plate supports lower Fold out cutlery basket lower Adjustable rinse aid dispenser Adjustable water softener Cold only water connection Interior light 45dBA
12 place settings 6 wash programs: Automatic 60 - 65 Bio 50 with pre-rinse 30 mins 60 Glass 45 Intensive care 70 Rinse and hold Extra wash options: Multi tab / 3 in 1 Delay start 1-19 hours Acoustic tone at end Program selection indicator Beam on floor indicator Turbo drying Water sensing system Flow through water heater Advanced fuzzy logic Auto load adjustment Anti-flood system Aqua alarm 2 spray arms plus ceiling shower 4 stage filter system Height adjustable upper basket Foldable cup supports upper Fold down wine glass rack upper Fold down dividable rack upper Fold down plate supports lower Fold out cutlery basket lower Adjustable rinse aid dispenser Adjustable water softener Cold only water connection Interior light 44dBA
12 place settings 8 wash programs: Automatic 50 - mins 60 Bio 50 with pre-rinse Glass 45 Intensive 70 Normal 50 Normal 65 with pre-rinse Rinse and hold Extra wash options: Multi tab / 3 in 1 Turbo drying Water sensing system Flow through water heater Advanced fuzzy logic Auto load adjustment Anti-flood system Aqua alarm 2 spray arms plus ceiling shower 4 stage filter system Height adjustable upper basket Foldable cup supports upper Fold down wine glass rack upper Fold down dividable rack upper Fold down plate supports lower Fold out cutlery basket lower Beer glass holder lower Adjustable rinse aid dispenser Adjustable water softener Cold only water connection Interior light 44dBA

Specifications

Cooktop shown not available in Australia or New Zealand
Dishwasher Specifications

F60850VIM

Type Colour (SS=Stainless steel) Place settings Wash programs Extra wash options (multi tab|delay start) LED display | LED indicators LED indicators: Time remaining Delay start End Door Filter Rinse aid Salt Spray arm Water Program end signal Turbo drying Active drying Water sensing system Flow through water heater Fuzzy logic auto load adjustment Anti-flood system Aqua alarm Spray levels Filter system levels Height adjustable upper basket Foldable cup support upper Fold down wine glass rack upper Fold down dividable rack upper Fold down plate support lower Fold out cutlery basket lower Beer glass holder lower Adjustable rinse aid dispenser Adjustable water softener Interior light Cold only water connection Energy star rating* Energy consumption per year* (kWh) WELS water star rating* Water usage* (ltr) Noise level (dBA) Voltage 240V / 50Hz

BU SS | | 3.2.5 15.
FI N/A | | 3.2 16.
SI SS | | 3.2 16.
BU = Built-under FI = Fully Integrated SI = Semi Integrated
= Tested using Energy Saving 50 program
= Tested using Eco 50 program
= Tested using Normal 50 program * = Tested in accordance with AS/NZS 2007.2 & AS/NZS 6400

Dimensions

Dishwasher Dimensions

F60850Vim F86070VI

816-880
*All measurements are in millimetres (mm)

Customer Care

Spare parts Home Service and Spare Parts can be contacted by phone using our toll free national numbers. Australia Service 49 Spare Parts 50 www.aeg-electrolux.com.au New Zealand Service 610 Spare Parts 620 www.aeg-electrolux.co.nz Customer care For more information on AEG-Electrolux products, please call our Customer Care team or visit our website. Australia 640 New Zealand 2230 Product information The descriptors and illustrations in this publication apply to the specific products and models described as at the date of issue. Under our policy of continuous product development, product specifications may change without notice. Prospective purchasers should therefore check with their retailer to ensure this publication correctly describes the products that are being offered for sale. All information supplied is to be used for general reference purposes only and is on the understanding that Electrolux Home Products Pty Ltd will not be liable for any loss, liability or damage of whatever kind arising as a result of reliance on such information. Colours of products illustrated are as close as printing limitations allow.
Delivery The purchase of a new appliance is an exciting experience. In selected areas, AEG-Electrolux customers can, for an additional charge, choose to have their new appliance delivered by our experienced staff. This service, at the customers option, includes the removal and recycling of packaging materials and even the old appliance if necessary. Delivery is available in Adelaide, Brisbane, Melbourne, Perth and Sydney. It may not be available in some rural locations and is not available in New Zealand. Home service Home Service is provided for repairs to appliances by trained technicians. For repairs to appliances that are outside the manufacturers warranty period and not required as a result of a manufacturing defect, a service fee is payable. Home Service is available throughout Australia and New Zealand. Warranty Electrolux Home Products warrants that for domestic applications the AEG-Electrolux products featured in this brochure are free from defects in materials and workmanship for 2 years (3 months warranty for commercial applications). All warranties are subject to the conditions set out in the warranty card accompanying the product when purchased.

Introduction

Advanced Engineering from Germany
AEG stands for Advanced Engineering from Germany. AEG-Electrolux has long been the most familiar and best-loved appliance brand in Germany and its easy to see why. Precision German engineering means unrivalled features, function and performance. All our appliances offer outstanding performance, versatility and reliability along with superb aesthetics to enhance your kitchen design. AEG-Electrolux products are developed and manufactured with meticulous attention to detail, using the best of modern design and the very latest technology.

AEG-Electrolux

AEG-Electrolux. We are part of the Electrolux family. Share more of our thinking at www.electrolux.com.au
Built-in Kitchen Appliances
Electrolux Home Products Australia telephone: 640 fax: 067 customercare@electrolux.com.au www.aeg-electrolux.com.au Electrolux Home Products New Zealand telephone: fax: customercare@electrolux.co.nz www.aeg-electrolux.co.nz
Printed on Hello Silk stock containing FSC Mixed Source Product and is Elemental Chlorine Free (ECF) and Totally Chlorine Free (TCF)

Range 2009

Cert no. SGS-COC-003898
Copyright 2009 Electrolux Home Products Pty Ltd ABN Print code: AEGBIC_Jan09

FAVORIT 65050 VI

Fully Integrated Dishwasher User Instructions

Dear customer,

Please read these user instructions carefully. Please observe the safety instructions on the first few pages of these user instructions! Please keep these user instructions for later reference. Pass them on to any subsequent owner of the appliance.
The warning triangle and/or specific words (Warning!, Caution!, Important!) are used to highlight instructions that are important for your safety or for the function of the appliance. It is imperative that these instructions are observed. This symbol or numbered instruction steps lead you step by step through the operation of the appliance. Next to this symbol you receive additional information and practical tips on using the appliance. Tips and instructions for the economical and environmentally conscious use of the appliance are marked with a clover leaf. In the event of a malfunction, these operating instructions contain information on how to rectify faults yourself, see the "What to do, if." section. If these instructions are insufficient, please contact your AEG Service Force Centre. In this respect please read the chapter "Service & Spare Parts".
Printed on paper manufactured with environmentally sound processes. He who thinks ecologically acts accordingly. 2

Contents

CONTENTS

Operating Instructions

. Safety Instructions. Disposal. Economical and Ecological Dishwashing. Appliance Features, Display and Control Panel. Display and control panel. Prior to using for the first time. Water softener. Setting the water softener. Special salt for the water softener. Setting the amount of special salt to be added. Adding special salt. Rinse aid. Activating/deactivating the inflow of rinse aid. Adding rinse aid. Adjusting Rinse Aid Dosing. Activating/deactivating the acoustic signal. In Daily Use. Loading Cutlery and Dishes. Loading Cutlery. Loading Pans, Frying Pans and Large Plates. Loading Cups, Glasses and Coffee Services. Adjusting the Height of the Upper Basket. Filling with Detergent. Use of "3 in 1"/ Combi Detergent Tablets. Concentrated Detergent. Detergent tablets. Automatic Wash Programmes. Selecting the programme (Programme Table). Starting a programme. Changing/interrupting/aborting a programme. Setting or changing the start delay. Load Sensing Sensor Logic. Switching off the dishwasher.
Care and Cleaning. 32 Cleaning the Filter. 33 What to do, if.Error messages are displayed.there are problems with the operation of the dishwasher.the wash results are not satisfactory. 36 36
Technical Data. 37 Notes for Test Institutes. 38
Installation and Connection Instructions.
Installing the Dishwasher. 39 Fitting the Furniture Door Panel. 40 Connecting the Dishwasher. Water Connection. Permitted water pressure. Connect the inlet hose. Water drain. Leak prevention system. Electrical Connection. Connections. 44 45

Guarantee Conditions

. 46. 47

Service and Spare parts

OPERATING INSTRUCTIONS

Safety Instructions

The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law. Nevertheless, as a manufacturer we consider it our obligation to make you aware of the following safety information:
Installation, Connection and Placing into Operation
The dishwasher may only be transported upright. Check the dishwasher for transport damage. Do not in any circumstances connect an appliance that is damaged. In the case of damage, please contact your retailer. Before installing the appliance, ensure that the nominal voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating is also to be found on the rating plate. For information on how to correctly install and connect up your dishwasher, please read the Installation section. Adaptors / connectors and extension cables must not be used.

Child Safety

This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the product. Keep all packaging away from children. Keep all detergents in a safe place out of childrens reach. The water in your dishwasher is not suitable for drinking. If there are still remnants of detergent in the appliance, there is a risk of burns! When disposing of an old appliance, cut off the power supply cable and remove any door catches, to prevent young children being trapped inside.

General Safety

Repairs to the dishwasher are only to be carried out by qualified service engineers. Improper repairs can give rise to significant hazards for the user. If your appliance needs repairing, please contact your local AEG Service Force Centre.
Never place the dishwasher in operation if the mains cable, water inlet or drain hose is damaged; or the control panel, work top or plinth area is damaged such that the inside of the appliance is freely accessible. If the mains lead is damaged, or is to be replaced for a longer lead, the cable (obtainable from AEG Service Force) must be replaced by a service engineer authorised by AEG. Never unplug the appliance by pulling on the cable, always pull the plug. Additions or modifications to the dishwasher are not permitted for safety reasons. Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded. In this way you will avoid anybody tripping over the open door and hurting themselves. Long bladed knives stored in an upright position are a potential hazard. Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket. When finished loading or unloading, close the door as an open door can be a hazard.

Correct Use

Only wash household dishes using the dishwasher. If the appliance is used for other purposes, or is used incorrectly, the manufacturer cannot accept any liability for any damage caused. Only use detergents specifically designed for use in domestic dishwashers. Do not put any solvents in the dishwasher. There is a risk of an explosion! The anti-flood system provides dependable protection against damage due to leaks. For this system to function correctly, the following preconditions must be met: The appliance must remain connected to the mains even when it is switched off. The dishwasher must be correctly installed. Always shut off the water supply at the tap when the dishwasher is not to be used for longer periods, e.g. when you are away on holiday. Do not sit or stand on the open door, the appliance may tip over.

The indicators are never illuminated while a programme is running.
Prior to using for the first time
Prior to using for the first time, remove all the clips with which the baskets are secured for transport. Then perform the following steps: 0 1. Adjust the water softener 2. Fill with Salt for the Water Softener 3. Fill with Rinse Aid

Water softener

To avoid scale deposits on the dishes and in the dishwasher, the dishes must be washed with soft water, i.e. water with a low lime content. The dishwasher therefore has a built-in water softener, in which tap water with a hardness of 4d (German degree) and harder is softened with the aid of special salt.
Your water supplier will be able to inform you about the hardness and hardness range of the water in your area. The water softener can be set manually using the water hardness switch; it can also be set electronically using the buttons on the control panel.
Water hardness Indication Number of on the acoustic multi-dissignals 1 play Manually Electronically 5 4* 0* 1 no salt necessary Adjusting the hardness setting
In d - - - - - - - - - 10 under 4
In mmol/l 3 9,0 - 12,5 7,6 - 8,9 6,5 - 7,5 5,1 - 6,4 4,0 - 5,0 3,3 - 3,9 2,6 - 3,2 1,9 - 2,5 0,7 - 1,8 under 0.7

10l 9l 8l 7l 6l 5l 4l

3l 2l 1l

III II I/II I

1) The water hardness will only be indicated acoustically if the acoustic signal has been activated. 2) (d) German degree, measure of the hardness of water 3) [mmol/l] millimol per litre, international unit for the hardness of water 4) On this setting the length of the programme may be slightly longer. *) Factory setting
Setting the water softener
Using the table as a guide, adjust the water softener to that which corresponds to the hardness of the water in your area: The dishwasher must be switched off. Setting manually: 1. Open the dishwasher door. 2. Remove the lower basket from the dishwasher. 3. Turn the hardness range switch to 0 or 1 (see table). 4. Replace the lower basket. Setting electronically: 5. Press the ON/OFF button. The LED indicators for all the buttons in the control panel that are now able to be selected will become illuminated.
If the only LED indicator illuminated is one that belongs to a programme button, this means that this programme has been activated. The programme must be cancelled (RESET): Press function buttons 2 and 3 simultaneously for approx. 1 second. The LED indicators for all the buttons in the control panel that are now able to be selected will become illuminated. 6. Press function buttons 2 and 3 simultaneously and keep them pressed. The LED indicators in function buttons 1 to 3 will flash. 7. Press function button 1. The LED indicator for function button 1 will flash. The multi-display will indicate the hardness setting. The number of the acoustic signals heard (only when the acoustic signal has been activated) also corresponds to the hardness setting. 8. Pressing function button 1 increases the hardness setting by 1. (Exception: hardness setting 1 follows hardness setting 10).

9. When the hardness setting is correct, press the ON/OFF switch. The hardness setting is now saved.
Special salt for the water softener
If the water hardness in your area is less than 4 d, then the water in your dishwasher does not need to be softened and you do not need to use special salt or salt substitute. Water can be softened in one of two ways: If you are using dishwasher detergent that already contains salt substitute, the detergent only is put into the detergent compartment. In this case the water softener must manually be set to 0 and electronically to 1 to ensure that no special salt is added. If you are using dishwasher detergent and special salt separately, the special salt is to be put into the salt container. In this case the water softener must manually be set to 0 and electronically to between 2 and 10 (depending on the water hardness in your area) to ensure that the special salt is dispensed from the salt container.
Only use special salt intended for dishwashers. Never fill the salt supply container with different types of salt (e.g. cooking or table salt) or detergent. This would destroy the water softener. Prior to filling with salt, please check each time that you really do have a packet of special salt in your hand.
Setting the amount of special salt to be added
Some appliances are equipped with an additional 3 in 1 function. If you use 3-in-1 dishwashing tablets and select the 3 in 1 function together with the programme, the inflow of special salt does not have to be deactivated (see 3 in 1 function).
Operating Instructions 0 1. Set the water softener manually and electronically to the desired water

hardness:

Manual setting 0 0-1 Electronic setting 1 2-10 Multi-display indicator Addition of special salt Do not add special salt. Addition of special salt via salt container (factory setting)

IL 2l to 10l

If the water softener is electronically set at 1 for the purpose of using detergent that includes special salt, the special salt indicator is deactivated.

Adding special salt

Adjusting the Height of the Upper Basket
Maximum Height of the Dishes in the Upper Basket Lower Basket With upper basket raised With upper basket lowered 22 cm 24 cm 31 cm 29 cm
The height of the basket can also be adjusted when it is loaded.
Lowering the Upper Basket: 0 1. Pull the upper basket out completely. 2. Holding the upper basket at the rear right, lift it as far as it will go and then lower it vertically. The upper basket will engage in the lower position. Raising the Upper Basket: 0 1. Pull the upper basket out completely. 2. Holding the upper basket at the rear right, lift it as far as it will go and then lower it vertically. The upper basket will engage in the higher position.

Filling with Detergent

Only use dishwasher detergent. Fill with detergent: Prior to the start of a wash programme (not for the pre wash programme). The detergent is released into the wash water during the programme.
Please observe the manufacturer's dosing and storage recommendations as stated on the detergent packaging. The detergent compartment is on the inside of the dishwasher door. 0 1. If the lid is closed: press release button (1). The lid springs open.
2. Fill the detergent dispenser with detergent. The markings indicate the dosing levels: 20 corresponds to approx. 20 ml of detergent, 30 corresponds to approx. 30 ml of detergent. 3. Close the lid and press until it locks into place.
If the dishes are very heavily soiled put additional detergent into the adjacent chamber (2). This detergent will take effect during the pre wash.
Use of "3 in 1"/ Combi Detergent Tablets
General Advice These products are tablets with combined detergent/rinse-aid and salt functions. 0 1. Before using these products you should first check that the water hardness in your supply is compatible with the use of these products as per the detergent manufacturers instructions (on the product packaging). 2. These products should be strictly used according to the detergent manufacturers instructions.
Do not place the tablets in the tub or the cutlery basket as this will result in poorer wash results. The tablets should be placed in the detergent doser. 3. If you encounter problems when using "3 in1" products for the first time then please contact the detergent manufacturers care line (the telephone number is given on the product packaging). Special Advice When using combination products, the rinse-aid and salt lights are no longer useful. It may be helpful therefore to switch the rinse aid off please note that only some dishwashers have this facility - and selecting the lowest possible setting for water hardness. For more information please refer to your instruction manual. If you decide to switch to the use of a standard detergent system we advise that you: Refill both the salt and rinse aid compartments. Switch the waterhardness setting to the highest possible position and run for three normal cycles without a load. Readjust the waterhardness setting again according to the conditions for your region (as per the instruction manual).

Main wash Final rinse -
ECO Pre-wash Main wash Intermediate rinse Final rinse Dry
Main wash 2x intermediate rinses Final rinse Dry
Consumption values: 4 Length 5 Energy Water

110 - 120 min.

90 - 110 min.

30 min. 0.8 kWh 9 litres

130 - 150 min.

73 min.

1.75 1.95 kWh 1.1 1.4 kWh 19 - 21 litres 12 - 19 litres
0.95 1.05 kWh 0.9 kWh 13 - 15 litres 14 litres
1) This programme is not suitable for dishes with dried-on leftovers. 2) Test programme for test institutes 3) The various stages in the programme have different volumes as the dishes are washed more intensely for short periods during certain stages of the programme to improve the effectiveness of cleaning. 4) The consumption values were obtained under standardised conditions. They are dependent on how full the basket are. Variations are therefore possible in practice. 5) If the water hardness is electronically set at level 10, the length of the programme may be slightly longer.

Starting a programme

0 1. Check that the dishes and cutlery are loaded in the dishwasher in such
a way that the spray arms are free to rotate. 2. Turn on the tap fully. 3. Press the ON/OFF button. The LED indicators for all the buttons in the control panel that are now able to be selected will become illuminated. 4. Press the relevant button for the programme required (see Programme Table). The programme display will become illuminated. The remaining time for the programme will be shown in the multi-display.
The remaining time for the programme is adjusted according to amount of dishes, degree of soiling, etc. 5. Close the dishwasher door. The programme will begin. If an error message is displayed in the multi-display and/or if an acoustic error message can be heard after the programme has begun, please read the section What to do if.
Changing/interrupting/aborting a programme
Only change or interrupt a programme that is in progress if it is absolutely necessary. After the appliance has been closed again, the air that has entered will be heated significantly and expand. As a result, water may collect in the base of the appliance and trigger the anti-flood system. Changing a programme

If you would like to change the programme before closing the dishwasher door, briefly press the button for the new programme. If you would like to change the programme after it has commenced, proceed as follows:
Hot steam may escape when the dishwasher door is opened. There is a risk of scalding! Be careful when opening the door of the dishwasher. 0 1. Open the door of the dishwasher. The programme will stop. 2. Press the button for the new programme and hold it down. First, the indicator for the programme that is currently running will flash.
After several seconds only the indicator for the new programme will be flashing. 3. Release the programme button. 4. Close the dishwasher door. The newly selected programme will commence from the beginning. Interrupting the programme by opening the dishwasher door 0 1. Open the door of the dishwasher. The programme will stop. 2. Close the dishwasher door. The programme will continue. Aborting the programme (RESET) 0 1. Open the door of the dishwasher. 2. Press function buttons 2 and 3 for approx. 1 second and keep them pressed. The LED indicators for all the buttons in the control panel that are now able to be selected will become illuminated. 3. Release the function buttons. The programme has been aborted. 4. Switch off the dishwasher by pressing the ON/OFF button.
Setting or changing the start delay
Using the start delay timer you can adjust when within the next 19 hours the programme is to begin. Setting the start delay: 0 1. Open the door of the dishwasher. 2. Press the ON/OFF button. The LED indicators for all the buttons in the control panel that are now able to be selected will become illuminated. 3. Continue pressing the b button until the number of hours until the programme is to start is flashing in the multi-display. 4. Press the button for the desired programme. The length of the selected programme will flash for a moment in the multi-display, and then the selected starting time will be displayed again. 5. Close the door. The programme will start automatically following a countdown of the hours set.
Changing the start delay: As long as the programme has not started, you are still able to cancel the start delay by pressing the b button. Cancelling the start delay: As long as the programme has not started you are still able to cancel the start delay. Continue pressing the b button until the length of the selected programme appears in the multi-display. The selected programme will begin immediately after the dishwasher door has been closed. Changing the programme after the start delay has been set: As long as the programme has not started, you are still able to change the start delay set by pressing a programme button. 0 1. Press the button for the new programme and hold it down. First, the indicator for the programme that has just been selected will flash. After several seconds only the indicator for the new programme will be flashing. 2. Release the programme button. 3. Close the door. The programme will start automatically following a countdown of the hours set.

Load Sensing Sensor Logic
If a wash programme is started even though there are only a few dishes in the upper and/or lower basket, an intelligent electronic system adjusts the amount of water and the duration of the wash programme to the number of dishes. By this means it is possible to wash only a few dishes quickly and economically. At half load (6 place settings), up to 2 litres of water and 0.2 kWh of electricity are saved.
Switching off the dishwasher
If the acoustic signal has been enabled, a continuous tone will sound for 15 seconds at the end of the programme. Hot steam may escape if the door is opened immediately after the programme has ended. Therefore: 0 1. Open the door carefully. 2. Switch off the dishwasher by pressing the ON/OFF button. All display indicators will go out. If you do not switch off the dishwasher, the acoustic signal will sound again 3 minutes later and 6 minutes later.
Removing the dishes Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool before they are removed. Leave the dishes in the dishwasher for approximately 15 minutes following the end of the programme to enable better drying and cooling down of dishes. Empty the lower basket first, then the upper basket. This will avoid water spots, which are caused by remaining water in the upper basket dripping onto the dishes in the lower basket.

Care and Cleaning

Do not under any circumstances use furniture care products or aggressive cleaners. If necessary, clean the controls only with a soft cloth and pure warm water. Occasionally check the internal containers, door seal, and water inlet for soiling, clean if necessary.

Cleaning the Filter

The filters should be checked and cleaned regularly. Dirty filters will give poor wash results. 0 1. Open the door, remove the lower basket. 2. The dishwasher filter system comprises a coarse/fine filter, microfilter and a flat filter. Unlock the filter system using the handle on the microfilter, and remove. 3. Turn the handle about a turn anticlockwise and remove. 4. Take hold of the coarse/fine filter (1/2) by the handle with the hole and remove from the microfilter (3) 5. Clean all filters thoroughly under running water. 6. Remove the flat filter (4) from the base of the washing compartment and clean both faces thoroughly
7. Put the flat filter back in the base of the washing compartment 8. Place the coarse/fine filter in the microfilter and press together. 9. Put the filter combination in place and lock by turning the handle clockwise to the stop. During this process ensure that the flat filter does not protrude above the base of the washing compartment.

.there are problems with the operation of the dishwasher.
Symptom Possible Cause Solution
The door of the dishwasher is Shut the door. not closed properly. Mains plug is not plugged in. Insert mains plug. The programme does not start. House fuse is defective. A start delay is selected. The washing compartment is made from rust-free stainless steel. Rust spots in the washing compartment are due to Rust spots are visible in rust particles from external the washing compart- sources (rust particles from water pipes, pans, cutlery, ment. etc.). Remove such spots with one of the stainless steel cleaners that are generally available on the market. There is a whistling noise during washing. The whistling is not a cause for concern. Replace fuse. If dishes are to be washed immediately cancel delay start timer. Only wash cutlery and dishes that are suitable for dishwasher use.
Close the lid of the special salt container securely.
Use a different brand of detergent.
.the wash results are not satisfactory.
The dishes are still dirty. The wrong wash programme was selected. The dishes were loaded is such a way that the wash waster did not reach all items. The baskets for the dishes must not be overloaded. The filter in the base of the washing compartment is dirty or incorrectly positioned. Detergent was not used or too little was used. In the case of scale deposits on the dishes: The special salt container is empty or the water softener is incorrectly adjusted. The drain hose is incorrectly laid. The dishes are wet and dull. Rinse aid was not used. The rinse aid container is empty. 36
There are streaks, milky spots or a bluish coating on glasses and dishes. Lower rinse aid dosing. There are dried water drops on the glasses and dishes. Increase rinse aid dosing. The detergent may be the cause. Contact the detergent manufacturers customer advisor.

Technical Data

Capacity: Permitted Water Pressure: Electrical Connection: 12 place settings including serving dishes 1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa) Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher door on the right.
Dishwasher: Free-Standing Appliances Dimensions: Max. Weight: 850 x 600 x 600 (H x W x D in mm) 54 Kg
Dishwashers that Can Be Integrated, Built-In Dishwashers Dimensions: Max. Weight: x 596 x 570 (H x W x D in mm) 50 Kg
Dishwashers that Can Be Fully Integrated Dimensions: Max. Weight: x 596 x 546 - 550 (H x W x D in mm) 50 Kg
; This appliance conforms with the following EU Directives: 73/23/EWG dated 19. 02. 1973 Low Voltage Directive 89/336/EWG dated 03. 05. 1989 (including Directive Amendment 92/31/EWG) EMC Directive

Permitted water pressure

Lowest permitted water pressure: 1 bar (=10 N/cm2 =100 kPa) Highest permitted water pressure: 10 bar (=100 N/cm2 =1 MPa) Consult your installer if the water pressure is less than 1 bar. In the case of a water pressure greater than 10 bar, a pressure reduction valve must be used (available from your dealer).

Connect the inlet hose

The water inlet hose must not be kinked, crushed or entangled when it is being connected up. Connect the threaded hose fitting (ISO 228-1:2000) on the water inlet hose to a tap with an external thread ( inch). Tighten the threaded hose fitting hand tight only. In order that access to the tap in the kitchen is not limited by the use of the dishwasher, we recommend the installation of an additional tap, or fitting a two way adapter to the existing tap. If you need a longer water inlet hose than that supplied, VDE approved complete hose sets are to be used. These are available from your local Service Force Centre. Do not use, for connection, old hoses which have been used for another appliance.
The following section is only applicable to dishwashers that have a safety valve on the threaded hose fitting for the tap:
Water inlet hose with safety valve
After connecting the double-walled water inlet hose, the safety valve is next to the tap. Therefore the water inlet hose is only under pressure while the water is running. If the water inlet hose starts to leak during this operation, the safety valve cuts off the running water and the draining pump in the dishwasher is switched on.
Please take care when installing the water inlet hose: The distance between the bottom edge of the safety value and the floor on which the dishwasher is standing must be at least 30 cm: The electrical cable for the safety valve is in the double-walled water inlet hose. Do not immerse the water inlet hose or the safety valve in water. If the water inlet hose or the safety valve is damaged, remove the mains plug immediately. A water inlet hose with safety valve must only be replaced by your local Service Force Centre. Place the water inlet hose in such a way that it is never higher than the bottom edge of the safety valve.

Water drain

Drain hose
The drain hose must not be kinked, crushed or entangled. Connecting the drain hose: Maximum permitted height: 1 metre. Minimum required height 40 cm above the lower edge of the machine. Extension hoses Extension hoses are available from AEG Service Force. The internal diameter of the extension hoses must be 19 mm to ensure that the function of the appliance is not impeded. Hoses may be laid a maximum of 3 metres horizontally; the maximum permitted height for the connection for the drain hose is then 85 cm. Sink outlet connection The outlet of the drain hose ( 19 mm) fits all commonly available sink outlet spigot types. The outer diameter of the spigot connection must be at least 15 mm. The drain hose must be fixed to the sink outlet connection using the hose clamp supplied. If the dishwasher is fitted at a high position If the dishwasher is installed at a high level, and the drainhose connection is less than 30 cm from the bottom of the appliance, adapter kit ET 111099520 must be fitted. This is available from Customer Service. Discharging into a standpipe When discharging into a standpipe, the upright standpipe should have a minimum, length of 30 cm (12) from the bottom of the elbow to the top of the pipe (see diagram). Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water.

Leak prevention system

To avoid damage caused by water leakage, the dishwasher is equipped with a leak prevention system. In the event of a fault, the safety valve in the appliance immediately interrupts the inflow of water and the drain pump is activated. In this way water can neither escape nor overflow. Any remaining water in the appliance is automatically pumped out.
The leak prevention system also works when the appliance is switched off the appliance must however not be disconnected from the mains. In the event of a fault when the appliance is switched on, a buzzing tone can also be heard.

Electrical Connection

Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person.
WARNING - This appliance must be earthed. The manufacturer declines any responsibility should these safety measures not be observed. Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. To isolate the dishwasher from the mains, remove the mains plug. Important: The plug must still be accessible after the appliance has been installed.

Changing a fuse

The appliance is supplied with a 13amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13amp ASTA approved (BS 1363A) fuse must be used. Green Should the plug need to be & Yellow replaced for any reason, proceed as described below. The wires on the mains lead are coloured in accordance with the following code.

Blue Brown

Green and Yellow : Earth Blue : Neutral Brown : Live

Cord Clamp

The wire coloured green and yellow must be connected to the terminal marked with the letter E or by the earth symbol or coloured green and yellow. The wire coloured blue must be connected to the terminal N or coloured black. The wire coloured brown must be connected to the terminal marked L or coloured red. Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath.
WARNING! A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that, if it is necessary to cut off the plug, it is disposed of safely and not retained.

Connections

The water inlet and drain hoses, as well as the mains cable must be connected beside the dishwasher as there is insufficient space behind the appliance. The plumbing and electrical installation example given below can only be regarded as a recommendation.
Two 45 or Straight Connections, Outer 19 mm, Length 30 mm

Double tap

Water inlet

Mains cable

Mains socket

GUARANTEE CONDITIONS

Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate. The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's operating and maintenance instructions. The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. All service work under this guarantee must be undertaken by a Service Force Centre. Any appliance or defective part replaced shall become the Company's property. This guarantee is in addition to your statutory and other legal rights. Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours in which case a premium will be charged. Exclusions This guarantee does not cover: Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable parts of glass or plastic. Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom. Appliances found to be in use within a commercial environment, plus those which are subject to rental agreements. Products of AEG manufacture which are not marketed by AEG. European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications: The guarantee starts from the date you first purchased your product. The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products. This guarantee relates to you and cannot be transferred to another user. Your new home is within the European Community (EC) or European Free Trade Area. The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal household. The product is installed taking into account regulations in your new country. Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Germany Italy Sweden UK Senlis Nrnberg Pordenone Stockholm Slough +33 (0) 29 +49 (0) 7378 +39 (0) +46 (0) 5360 +44 (0) 1753 219899