Reviews & Opinions
Independent and trusted. Read before buy AEG-electrolux F86050VI!

AEG-electrolux F86050VI

Manual

Preview of first few manual pages (at low quality). Check before download. Click to enlarge.
Manual - 1 page  Manual - 2 page  Manual - 3 page 

Download (English)
AEG-electrolux F86050VI Dishwasher, size: 791 KB
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

AEG-electrolux F86050VIAbout AEG-electrolux F86050VI
Here you can find all about AEG-electrolux F86050VI like manual and other informations. For example: review.

AEG-electrolux F86050VI manual (user guide) is ready to download for free.

On the bottom of page users can write a review. If you own a AEG-electrolux F86050VI please write about it to help other people.

 

[ Report abuse or wrong photo | Share your AEG-electrolux F86050VI photo ]

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

No opinions have been provided. Be the first and add a new opinion/review.

 

Documents

doc0

FAVORIT 86050 VI

Fully Integrated Dishwasher User Instructions

Dear customer,

Please read these user instructions carefully. Please observe the safety instructions on the first few pages of these user instructions! Please keep these user instructions for later reference. Pass them on to any subsequent owner of the appliance.
The warning triangle and/or specific words (Warning!, Caution!, Important!) are used to highlight instructions that are important for your safety or for the function of the appliance. It is imperative that these instructions are observed. This symbol or numbered instruction steps lead you step by step through the operation of the appliance. Next to this symbol you receive additional information and practical tips on using the appliance. Tips and instructions for the economical and environmentally conscious use of the appliance are marked with a clover leaf. In the event of a malfunction, these operating instructions contain information on how to rectify faults yourself, see the "What to do, if." section. If these instructions are insufficient, please contact your AEG Service Force Centre. In this respect please read the chapter "Service & Spare Parts".
Printed on paper manufactured with environmentally sound processes. He who thinks ecologically acts accordingly. 2

Contents

CONTENTS

Operating Instructions

. Safety Instructions. Disposal. Economical and Ecological Dishwashing. Appliance Features, Display and Control Fields. Display and Control Panels. Prior to using for the first time. Adjusting the Water Softener. Filling with Salt for the Water Softener. Rinse Aid. Switching Rinse Aid Supply On and Off. Filling with Rinse Aid. Adjusting Rinse Aid Dosing. Switching the Acoustic Signal for the End of the Wash Programme On and Off. In Daily Use. Loading Cutlery and Dishes. Loading Cutlery. Loading Pans, Frying Pans and Large Plates. Loading Cups, Glasses and Coffee Services. Adjusting the Height of the Upper Basket. Filling with Detergent. Concentrated Detergent. Detergent tablets. Automatic Wash Programmes. Selecting the Wash Programme (Programme Table). Start the Wash Programme. Deleting a Wash Programme. Interrupting the Wash Programme (only in emergencies). Setting or Changing the Delay Start Timer. Load Sensing Sensor Logic. Switching Off the Dishwasher. Emptying the Dishwasher.
Care and Cleaning. 28 Cleaning the Filter. 28 3
What to do, if. Warning tones indicating a fault in the dishwasher.there are problems with the operation of the dishwasher.the wash result is not satisfactory.
Technical Data. 32 Notes for Test Institutes. 33
Installation and Connection Instructions.
Installing the Dishwasher. 34 Fitting the Furniture Door Panel. 35 Connecting the Dishwasher. Water Connection. Permitted water pressure. Connect the inlet hose. Water drain. Leak Prevention System. Electrical Connection. Connections. 40 41

Guarantee Conditions

. 42. 43

Service and Spare parts

OPERATING INSTRUCTIONS

Safety Instructions

The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law. Nevertheless, as a manufacturer we consider it our obligation to make you aware of the following safety information:
Installation, Connection and Placing into Operation
The dishwasher may only be transported upright. Check the dishwasher for transport damage. Do not in any circumstances connect an appliance that is damaged. In the case of damage, please contact your retailer. Before installing the appliance, ensure that the nominal voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating is also to be found on the rating plate. For information on how to correctly install and connect up your dishwasher, please read the Installation section. Adaptors / connectors and extension cables must not be used.

Child Safety

This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the product. Keep all packaging away from children. Keep all detergents in a safe place out of childrens reach. The water in your dishwasher is not suitable for drinking. If there are still remnants of detergent in the appliance, there is a risk of burns! When disposing of an old appliance, cut off the power supply cable and remove any door catches, to prevent young children being trapped inside.

General Safety

Repairs to the dishwasher are only to be carried out by qualified service engineers. Improper repairs can give rise to significant hazards for the user. If your appliance needs repairing, please contact your local AEG Service Force Centre.
Never place the dishwasher in operation if the mains cable, water inlet or drain hose is damaged; or the control panel, work top or plinth area is damaged such that the inside of the appliance is freely accessible. If the mains lead is damaged, or is to be replaced for a longer lead, the cable (obtainable from AEG Service Force) must be changed by a service engineer authorised by AEG. Never unplug the appliance by pulling on the cable, always pull the plug. Additions or modifications to the dishwasher are not permitted for safety reasons. Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded. In this way you will avoid anybody tripping over the open door and hurting themselves. Long bladed knives stored in an upright position are a potential hazard. Sharp knives and items of cutlery with sharp edges must be placed in the cutlery tray or in the upper rack. When finished loading or unloading, close the door as an open door can be a hazard.

Correct Use

Only wash household dishes using the dishwasher. If the appliance is used for other purposes, or is used incorrectly, the manufacturer cannot accept any liability for any damage caused. Only use detergents specifically designed for use in domestic dishwashers. Do not put any solvents in the dishwasher. There is a risk of an explosion! The anti-flood system provides dependable protection against damage due to leaks. For this system to function correctly, the following preconditions must be met: The appliance must remain connected to the mains even when it is switched off. The dishwasher must be correctly installed. Always shut off the water supply at the tap when the dishwasher is not to be used for longer periods, e.g. when you are away on holiday. Do not sit or stand on the open door, the appliance may tip over.
In the event of a fault, first close the tap, then switch off the appliance and unplug it from the mains. If the appliance is permanently wired to the mains: remove the fuse.

Disposal

Disposing of the Packaging Material
Dispose of the dishwasher packaging material correctly. All the packaging materials used are harmless to the environment and can be recycled. Plastic parts are marked with standard international abbreviations: >PE< for polyethylene, e.g. sheet wrapping material >PS< for polystyrene, e.g. padding material (always CFC-free) >POM< for polyoxymethylene, e.g. plastic clips Cardboard packaging is manufactured from recycled paper and should be deposited in the waste paper collection for recycling.
Disposal of Old Appliances
When disposing of old appliances, remove the plug and ensure that any locks or catches are removed to prevent young children becoming trapped inside. Use an authorised disposal site.
Economical and Ecological Dishwashing
Ensure that the water softener is correctly adjusted. Do not pre-rinse dishes under running water. If you wash a small load, the load sensor calculates the amount of water necessary and shortens the programme. It is more economical to always wash with a full load. Select the wash programme to suit the nature and degree of the soiling on the dishes. Do not use more detergent, special salt or rinse aid than is recommended in these operating instructions and by the detergent manufacturer. The dishwasher's interior light is always switched on as long as the door of the appliance is open. To save energy you should therefore always close the door of the dishwasher after loading or removing dishes. 7

Appliance Features, Display and Control Fields
Top Spray Arm Rubber Seal for Connecting the Water Feed to the Upper Spray Arm Spray Arms Water Hardness Switch Container for Salt Container for Rinse Aid Detergent Dispenser
Display and Control Fields

Rating Plate Filters

Display and Control Panels
Function buttons Display for set delay start Indicators

Control panel

Set delay start
Display for the individual programme steps
The control panel consists of the ON/OFF button 9 and the programme buttons with LED displays. Function buttons: In addition to the stated wash programme the following functions can also be set using these buttons:
Function button 1 Function button 2 Function button 3 Function button 4 Switch acoustic signal on and off Adjust the water softener Switch rinse aid supply on and off - is not occupied -
Indicators have the following significance:
Refill with special salt Refill with rinse aid Open the tap
Prior to using for the first time
Prior to using for the first time, remove all the clips with which the dish racks are secured for transport. Then perform the following steps: 0 1. Adjust the water softener 2. Fill with Salt for the Water Softener 3. Fill with Rinse Aid
Adjusting the Water Softener
To prevent the build up of scale on dishes and in the dishwasher, the dishes must be washed with soft, i.e. low lime content water. For this reason the dishwasher is fitted with a water softener in which tap water from a hardness of 4 d (German degree) is softened with the aid of special salt.
Your local water authority can advise you on the hardness of the water in your area. Adjust the water softener as stated in the table to the setting that corresponds to the hardness of the water in your area. The water softener can be set manually using the water hardness switch and also electronically using the buttons on the control panel.
Water Hardness in d1) 51 - - - - - - - - - 10 under 4 in ppm2) 9,0 - 12,5 7,6 - 8,9 6,5 - 7,5 5,1 - 6,4 4,0 - 5,0 3,3 - 3,9 2,6 - 3,2 1,9 - 2,5 0,7 - 1,8 under 0.7 Range Hardness Setting Manual Electronic 3* 2 0* I/II I no salt necessary Number of Flashes 3 2

III II

1)(d) German degrees, a measure of water hardness 2)(ppm), Parts Per Million *factory setting
Adjust the water softener to the hardness of the water in your area as stated in the table: 0 1. The dishwasher must be switched off. 2. Manual adjustment: Open the dishwasher door. 3. Remove the lower rack from the dishwasher. 4. Turn the water hardness switch to 0 or 1. 5. Re-position the lower rack. 6. Electronic adjustment: Simultaneously press and hold down function buttons 1 and 2. 7. Press the ON/OFF button. The LED displays for the engaged function buttons will flash. 8. Press function button 2 again. The LED display for function button 2 will flash. The number of flashes corresponds to the hardness setting. (Exception: hardness setting 0 is indicated by 10 flashes). The sequence of flashes is repeated several times after a 5 second pause. 9. Pressing function button 2 increases the hardness setting by 1. (Exception: hardness setting 0 follows hardness setting 9). 10. Once the hardness setting is set correctly, press the ON/OFF switch. The hardness setting is then saved.

Check the salt and rinse aid levels. Load cutlery and dishes into the dishwasher Fill with dishwasher detergent Select a wash programme suitable for the cutlery and dishes Start the wash programme
Loading Cutlery and Dishes
Sponges, household cloths and any object that can absorb water should not be washed in the dishwasher.
For washing in the dishwasher the following cutlery/dishes are not suitable: Cutlery with wooden, horn, china or mother of pearl handles Plastic items that are not heat resistant Older cutlery with glued parts that is not temperature resistant Bonded cutlery items or dishes Pewter or copper items Lead crystal glass Steel items subject to rusting Wooden platters Items made from synthetic fibres are of limited suitability: Only wash stoneware in the dishwasher if it is specifically marked as being dishwashersafe by the manufacturer. Glazed patterns may fade if machine washed frequently. Silver and aluminium parts have a tendency to discolour during washing. Left-overs, e.g. egg white, egg yolk and mustard often cause discolouring and staining on silver. Therefore always clean left-overs from silver immediately, if it is not to be washed straight after use. Some types of glass can become dull after a large number of washes.
Before loading the dishes, you should: Remove all scraps of food. Soften remnants of burnt food in pans. When loading the dishes and cutlery, please note: Dishes and cutlery must not impede the rotation of the spray arms. Load hollow items such as cups, glasses, pans, etc. with the opening downwards so that water cannot collect in the container or a deep base. Dishes and items of cutlery must not lie inside one another, or cover each other 16
To avoid damage to glasses, they must not touch Do not lay small objects (e.g. lids) in the cutlery rack

Loading Cutlery

Long bladed knives stored in an upright position are a potential hazard. Long and/or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket. Take care when loading or unloading sharp items such as knives. Place knives, small spoons and small forks in the cutlery tray.
Place forks and spoons that do not fit in the cutlery tray in the cutlery basket. To ensure that all items of cutlery in the cutlery basket are properly washed, you should 0 1. Place the grid insert on the cutlery rack 2. Place forks and spoons in the grid insert on the cutlery basket with the handle downwards. 3. For larger items of cutlery, e.g. a whisk, half of the top for the cutlery basket can be left off.

Main wash Rinsing Final rinse -
Consumption Figures: 3) Duration Energy Water
110 - 120 min. 1.75 - 1.95 kWh 19 - 21 litres
95 - 115 min. 1.10 - 1.35 kWh 11.5 - 19 litres

30 min. 0.8 kWh 8 litres

130 - 150 min. 0.95 -1.05 kWh 12 -14 litres
35 min. 0.7 kWh 11 litres

2) 3) 4) 5)

In addition to the wash programmes given in the table there is the special programme Pre wash A. Using this programme you can give an initial wash to dishes that are to be stored in the dishwasher ready to be washed later. The special programme Pre wash A lasts 12 minutes and uses 4 litres of water and less than 0.1 kWh of energy. Noise levels vary at different stages of the wash programme as at some programme stages the dishes are washed more energetically so that they will be cleaned more thoroughly. The consumption figures were determined under standard conditions. They are intended as a guide only and depend on the loading. For this reason figures may vary in practice. This programme is not suitable when left-overs have dried on. Test programme for test institutes

Start the Wash Programme

2. Check that when the dishes and cutlery are loaded into the dishwasher the spray arms are free to rotate. 3. Open the tap fully. 4. Press the ON/OFF button. The indicator in the ON/OFF button illuminates. 5. Press the programme button for the desired programme (see "Programme Table"). The programme indicator illuminates. Have you accidentally selected the wrong wash programme? If you want to change the wash programme within 6 seconds of making a programme selection, briefly press the button for the new wash programme. If you want to change the wash programme at a later point in time, use the following procedure: Press the button for the new wash programme and hold it pressed. The indicators for both programmes now flash. After a few seconds only the indicator for the new programme flashes. Release the programme button, the new wash programme has been saved. 6. Close the door. After around 6 seconds the selected wash programme begins.
If acoustic warning tones can be heard after the start of the programme, please read the "What to do, if." section.
Deleting a Wash Programme
A selected wash programme can only be deleted when the door of the dishwasher is still open, however a programme cannot be deleted in the first 6 seconds after making a programme selection. After 6 seconds the wash programme can be deleted as follows: 0 1. Press the button for the current wash programme and hold it pressed. The programme indicator for the current wash programme flashes for a few seconds and then extinguishes. 2. Release the programme button, the wash programme is deleted.
A selected programme is not deleted by switching off the dishwasher.

Interrupting the Wash Programme (only in emergencies)
Interrupt a wash programme in progress only when it is absolutely necessary to do so. When the appliance is closed again, the air that has entered the appliance is heated and expands significantly. As result water may penetrate into the base of the appliance and trigger the leak prevention system.
Hot steam may escape from the appliance when opening the door. Open the door carefully. 0 1. Open the door of the dishwasher. 2. Rectify the reason for opening the appliance. 3. Close the door. The selected programme will then continue.
Setting or Changing the Delay Start Timer
Using the delay start timer it is possible to set a wash programme to start within the next 3, 6 or 12 hours. 0 1. Press the ON/OFF button. 2. Press the button for the desired wash programme 3. Setting the delay start: Keep pressing the X button until the indicator next to the number of hours of delay illuminates. Changing the delay start: As long as the wash programme has not started, you can still change the delay start set by pressing the X button. Cancelling the delay start timer: Providing the wash programme has not started you can cancel the delay start timer. Keep pressing the X button until none of the three hour displays is illuminated. The selected wash programme will begin immediately the dishwasher door is closed.
If a delay start is selected, the programme progress display does not illuminate. 4. Close the door.
Load Sensing Sensor Logic
If a wash programme is started even though there are only a few dishes in the upper and/or lower rack, an intelligent electronic system adjusts the amount of water and the duration of the wash programme to the number of dishes. By this means it is possible to wash only a few dishes quickly and economically. At half load (6 place settings), up to 2 litres of water and 0.2 kWh of electricity are saved.
Switching Off the Dishwasher
Do not switch off the dishwasher until the display L is illuminated. If the acoustic signal has been switched on there will be a continuous signal for 5 seconds at the end of the wash programme. Hot steam may escape if the door is opened immediately after the end of the programme. Open the door carefully. 0 1. Open the door. 2. Press the ON/OFF button. The display in the ON/OFF button will go out. If the dishwasher is not switched off, the acoustic signal is repeated after 10 minutes.

Emptying the Dishwasher

Hot dishes can be sensitive to knocks. The dishes should therefore be allowed to cool down before removing them from the appliance. Leave the dishes in the dishwasher for approx. 15 minutes after the end of the programme so that they dry better and can cool down. Empty the lower rack first, then the upper rack. This will avoid any water left on the upper rack dripping onto the dishes in the lower rack and causing water spots.

Care and Cleaning

Do not under any circumstances use furniture care products or aggressive cleaners. If necessary, clean the controls only with a soft cloth and pure warm water. Occasionally check the internal containers, door seal, and water inlet for soiling, clean if necessary.

Cleaning the Filter

The filters should be checked and cleaned regularly. Dirty filters will give poor wash results. 0 1. Open the door, remove the lower rack. 2. The dishwasher filter system comprises a coarse/fine filter, microfilter and a flat filter. Unlock the filter system using the handle on the microfilter, and remove. 3. Turn the handle about a turn anticlockwise and remove. 4. Take hold of the coarse/fine filter (1/2) by the handle with the hole and remove from the microfilter (3) 5. Clean all filters thoroughly under running water. 6. Remove the flat filter (4) from the base of the washing compartment and clean both faces thoroughly
7. Put the flat filter back in the base of the washing compartment 8. Place the coarse/fine filter in the microfilter and press together. 9. Put the filter combination in place and lock by turning the handle clockwise to the stop. During this process ensure that the flat filter does not protrude above the base of the washing compartment.
The dishwasher must not be used without filters under any circumstances.

What to do, if.

Try to rectify minor faults on the dishwasher with the aid of the instructions given here. If you call an engineer to resolve a of fault listed here, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is in guarantee.
. Warning tones indicating a fault in the dishwasher.
If one or two repetitive warning tones can be heard after the start of a programme, they are indicative of a fault in the dishwasher that you can probably rectify yourself. After rectification of the fault, press the button for the wash programme that has been started and close the door of the dishwasher. The wash programme continues. If the same warning tone is heard again, please contact customer service. If more than two repetitive warning tones can be heard after programme start, please contact customer service. Customer service will need to know the number of tones and which indicators on the control and display field are flashing.

Malfunction Possible Cause Solution Clean tap.
1 continuously repeated Tap is blocked or furred warning tone can be heard, with lime-scale. the programme display is flashing in the control and The filter (where present) in the threaded hose fitdisplay field, and the ^ ting at the water inlet control indicator is perma- valve is blocked. nently illuminated: no water is running into the The water inlet hose is not correctly laid. dishwasher. 2 warning tones that are continuously repeated can be heard, the programme display and The siphon is blocked.
Clean the filter in the threaded hose fitting.
Check hose installation. Clean siphon.
The water drain hose is the I indicator on the not correctly laid. control and display field are flashing. 3 warning tones that are continuously repeated can be heard and the I and

Check hose installation.

L indicators on the control and display field are flashing.
The leak prevention system has been triggered.
Close the tap and contact your local AEG Sevice Force Centre.
.there are problems with the operation of the dishwasher.
Symptom Possible Cause Solution
The door of the dishwasher is Shut the door. not closed properly. Mains plug is not plugged in. Insert mains plug. The programme does not start. House fuse in defective. A delay start is selected. The washing compartment is made of corrosion-resistant stainless steel. Rust spots in the washing compartment Rust spots are visible in are from particles from outthe washing compart- side the appliance (rust particles from the water pipe, ment. from pans, cutlery, etc.). Remove such spots with a commercially available stainless steel cleaner. There is a whistling noise during washing. The whistling is not a cause for concern. Replace fuse. If the dishes are to be washed immediately, set the delay start to 0 hours Only wash cutlery and dishes that are suitable for dishwasher use.
Close the lid of the special salt container securely.
Use a different brand of detergent.
Mains plug is not plugged in. Insert mains plug. Dishwasher interior lighting does not work. Light bulb for the interior Contact AEG Service Force. lighting is defective.
.the wash result is not satisfactory.
The dishes are still dirty. The wrong wash programme was selected. The dishes were arranged in such a manner that water has not reached all parts. The dish racks must not be overloaded. The filter in the base of the washing compartment is dirty or incorrectly positioned. Detergent was not used or too little was used. In the case of scale deposits on the dishes: the special salt container is empty or the water softener is incorrectly adjusted. 31

The drain hose is incorrectly laid. The dishes are wet and dull. Rinse aid was not used. The rinse aid container is empty. There are streaks, milky spots or a bluish coating on glasses and dishes. Decrease rinse aid dosing. There are dried water drops on the glasses and dishes. Increase rinse aid dosing. The detergent may be the cause. Contact the detergent manufacturer's consumer advisor.

Technical Data

Capacity: Permitted Water Pressure: Electrical Connection: 12 place settings including serving dishes 1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa) Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher door on the right.
Dishwasher: Free-Standing Appliances Dimensions: Max. Weight: 850 x 600 x 600 (H x W x D in mm) 54 Kg
Dishwashers that Can Be Integrated, Built-In Dishwashers Dimensions: Max. Weight: x 596 x 570 (H x W x D in mm) 50 Kg
Dishwashers that Can Be Fully Integrated Dimensions: Max. Weight: x 596 x 546 - 550 (H x W x D in mm) 50 Kg
; This appliance conforms with the following EU Directives: 73/23/EWG dated 19. 02. 1973 Low Voltage Directive 89/336/EWG dated 03. 05. 1989 (including Directive Amendment 92/31/EWG) EMC Directive 32
Notes for Test Institutes
Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test programme (see Programme Table). Tests in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme (see Programme Table).
Full Load: 12 place settings incl. serving dishes Detergent Dosing: Rinse Aid Setting: 5g + 25g (Type B) 4 (Type III) Half Load: 6 place settings incl. serving dishes, leaving alternate positions free 20g (Type B) 4 (Type III)
Sample loading arrangements: Upper basket without cutlery tray
Upper basket with cutlery tray
Lower basket with cutlery basket

Cutlery basket

Installation and Connection Instructions

Please take care when installing the water inlet hose: The distance between the bottom edge of the safety value and the floor on which the dishwasher is standing must be at least 30 cm: The electrical cable for the safety valve is in the double-walled water inlet hose. Do not immerse the water inlet hose or the safety valve in water. If the water inlet hose or the safety valve is damaged, remove the mains plug immediately. A water inlet hose with safety valve must only be replaced by your local Service Force Centre. Place the water inlet hose in such a way that it is never higher than the bottom edge of the safety valve.

Water drain

Drain hose
The drain hose must not be kinked, crushed or entangled. Connecting the drain hose: Maximum permitted height: 1 metre. Minimum required height 30 cm above the lower edge of the machine. Extension hoses Extension hoses are available from AEG Service Force. The internal diameter of the extension hoses must be 19 mm to ensure that the function of the appliance is not impeded. Hoses may be laid a maximum of 3 metres horizontally; the maximum permitted height for the connection for the drain hose is then 85 cm. Sink outlet connection The outlet of the drain hose ( 19 mm) fits all commonly available sink outlet spigot types. The outer diameter of the spigot connection must be at least 15 mm. The drain hose must be fixed to the sink outlet connection using the hose clamp supplied. If the dishwasher is fitted at a high position If the dishwasher is installed at a high level, and the drainhose connection is less than 30 cm from the bottom of the appliance, adapter kit ET 111099520 must be fitted. This is available from Customer Service. Discharging into a standpipe When discharging into a standpipe, the upright standpipe should have a minimum, length of 30 cm (12) from the bottom of the elbow to the top of the pipe (see diagram). Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water.

Leak Prevention System

For protection from damage due to water leaks, the dishwasher is equipped with a leak prevention system, the AQUA CONTROL SYSTEM. In the event of a fault, the safety valve immediately interrupts the supply of water to the appliance and the drain pump switches on. It is thus not possible for water to either leak or overflow. Any water left in the appliance is automatically pumped out.

The AQUA CONTROL SYSTEM also works when the appliance is switched off the appliance must however not be disconnected from the mains. When the appliance is switched on, a buzzing tone can also be heard.

Electrical Connection

Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person.
WARNING - This appliance must be earthed. The manufacturer declines any responsibility should these safety measures not be observed. Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. To isolate the dishwasher from the mains, remove the mains plug. Important: The plug must still be accessible after the appliance has been installed.

Changing a fuse

The appliance is supplied with a 13amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13amp ASTA approved (BS 1363A) fuse must be used. Green Should the plug need to be & Yellow replaced for any reason, proceed as described below. The wires on the mains lead are coloured in accordance with the following code.

Blue Brown

Green and Yellow : Earth Blue : Neutral Brown : Live

Cord Clamp

The wire coloured green and yellow must be connected to the terminal marked with the letter E or by the earth symbol or coloured green and yellow. The wire coloured blue must be connected to the terminal N or coloured black. The wire coloured brown must be connected to the terminal marked L or coloured red. Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath.
WARNING! A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that, if it is necessary to cut off the plug, it is disposed of safely and not retained.

Connections

The water inlet and drain hoses, as well as the mains cable must be connected beside the dishwasher as there is insufficient space behind the appliance. The plumbing and electrical installation example given below can only be regarded as a recommendation.
Two 45 or Straight Connections, Outer 19 mm, Length 30 mm

Double tap

Water inlet

Mains cable

Mains socket

GUARANTEE CONDITIONS

1. Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance. The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser, which must be verified by purchase invoice or similar documentation. The guarantee does not cover commercial use. The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials. The guarantee does not cover appliances where defects or poor performance are due to misuse, accidental damage, neglect, faulty installation, unauthorised modification or attempted repair, commercial use or failure to observe requirements and recommendations set out in the instruction book. This guarantee does not cover such parts as light bulbs, removable glassware or plastic, dust bags or filters. Should guarantee repairs be necessary the purchaser must inform the nearest customer service office (manufacturers service or authorised agent). AEG reserves the right to stipulate the place of the repair (i. e. the customers home, place of installation or AEG workshop). The guarantee or free replacement includes both labour and materials. Repairs carried out under guarantee do not extend the guarantee period for the appliance. Parts removed during guarantee repairs become the property of AEG. The purchasers statutory rights are not affected by this guarantee. European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications: The guarantee starts from the date you first purchased your product. The guarantee is for the same period and to the same extent for labour and parts as exist in the new country of use for this brand or range of products. This guarantee relates to you and connot be transferred to another user. Your new home is within the European Community (EC) or European Free Trade Area. The product is installed and used in accordance with our instructions and is only used domestically, i. e. a normal household. The product is installed taking into account regulations in your new country. Before you move please contact your nearest Customer Care Centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Germany Italy Sweden UK Senlis Nrnberg Pordenone Stockholm Slough +33 (0) +49 (0) 7378 +39 (0) +46 (0) 5360 +44 (0) 1753 219899

4. 5. 6.

SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact Service Force by telephoning: 929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the adress of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.uk Before calling out an engineer, please ensure you have read the details under the heading What to do if.. When you contact the Service Force Centre you will need to give the following details: 1. Your name, address and post code. 2. Your telephone number 3. Clear and concise details of the fault. 4. The model and serial number of the appliance (found on the rating plate).
5. The purchase date Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee service calls. Customer Care For general enquiries concerning your AEG appliance or for further information on AEG products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.aeg.co.uk. Customer Care Department AEG Domestic Appliances 55-77 High Street Slough Berkshire, SL1 1DZ Tel. (*) (*) Calls may be recorded for training purposes
AEG Hausgerte GmbH Postfach 1036 D-90327 Nrnberg http://www.aeg.hausgeraete.de Copyright by AEG 343 - 01 - 0602 Subject to change without notice

 

Tags

XR-C8100R WMC1070 NVX-P1 FAX-phone 11 UN55C9000SM Iphoto Sony A828 S-HTD540 L-558 32PFL5403D 12 CZ21A083N CQ-C7305N 360 M1 BC-CSQ2 Cdm1 SE MC 520 DC-J121 VGN-N38e-W LAV72330-W TDA1526 LAC7800 TX-P42x10E MRP-T306 FS-210 Studio AVR-683 VGC-V2M DSS-16- VC-6713H Vision 1000 2 P4330 MRF-350 Pta42 IM600 USB Edirol V1 AR-M150 155 CDX-828 PL42C430a1 XRS 930 1000 W FFH-DV25AD BAR626 HR-S9600 DCR-DVD703E Businessphone 250 Sans FIL IDP-562 Mastercontrol Scenic EB Kd-s13 ICF-CD853V Dect6231S Server SE6R2 LE-40R72B NV-GS280 NV-VJ82PN WF338AAW K1000 Scrambler VSX-AX4asi-S Ii 24 Vario KX-W1030 Metal QG3040 UX-Y303CW WAP55AG Rmrk50P-RM-rk50 3000 XL DCR-PC101E Syncmaster 753S CDX-4250R PM-2000 FL573CN B1045AV 81834 Precision 420 SHB6100 KLV-S20g10 NAD 310 LN23R51BX Dual-S KAC-849 20 R AT3220A FA489 Gun G15 Stylus C40 160 A Blackberry 950 874m 884M Pundit-AE3 X204N XL-MP150E S740 CTK-200 Saffire Review Ique 3000

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101