Here you can find all about AEG-electrolux FAV40850 like manual and other informations. For example: review.
AEG-electrolux FAV40850 manual (user guide) is ready to download for free.
On the bottom of page users can write a review. If you own a AEG-electrolux FAV40850 please write about it to help other people. [ Report abuse or wrong photo | Share your AEG-electrolux FAV40850 photo ]
AEG-electrolux FAV40850 Dishwasher, size: 793 KB
User reviews and opinions
No opinions have been provided. Be the first and add a new opinion/review.
Water hardness in d1)) 51 - - - - - - - - - 10 below 4 in mmol/l2)) 9,0 - 12,5 7,6 - 8,9 6,5 - 7,5 5,1 - 6,4 4,0 - 5,0 3,3 - 3,9 2,6 - 3,2 1,9 - 2,5 0,7 - 1,8 below 0.7 Range Adjusting the hardness setting Manual Electronic 103) 5 4* 0* 1 no salt necessary Indication on the multi-display
10L. 9L 8L 7L 6L 5L 4L 3L 2L 1L
III II I/II I
1) (d) German degree, measure of the hardness of water 2) [mmol/l] millimol per litre, international unit for water hardness 3) On this setting the length of the dishwashing cycle may be slightly longer. *) factory setting
Adding dishwasher Salt
To decalcify the water softener, it must be filled up with dishwasher salt. Use only special salt suitable for domestic dishwashers. If you do not use 3 in1 detergent, fill up with dishwasher salt: Before using the dishwasher for the first time. When the control indicator for dishwasher salt is illuminated on the control panel. 1. Open the door and remove the lower basket. 2. Unscrew the lid on the salt dispenser by turning it anti-clockwise. 3. Only when using the dishwasher for the first time: Fill the salt dispenser with water. 4. Place the funnel (supplied) over the dispenser opening. Fill the dispenser with dishwasher salt; the capacity of the dispenser is approx. 1.0-1.5 kg, depending on the size of the grains. Do not overfill the dispenser. If water overflows when filling up with dishwasher salt, this is completely harmless. 5. Clean away any salt remnants from the dispenser opening. 6. Screw the lid back on in a clockwise direction. 7. Run a dishwashing cycle after filling the salt dispenser with dishwasher salt. This will wash away salt water and salt crystals that have been spilt. Depending on the size of the salt granules, it can take several hours for the salt to dissolve in the water and for the control indicator for dishwasher salt to go out.
Filling Up with Rinse Aid
Rinse aid causes the rinse water to flow easily from the crockery leaving gleaming dishes and glassware. If you do not use 3in1 detergent, fill up with rinse aid: Before using the dishwasher for the first time. When the control indicator for rinse aid is illuminated on the control panel. Use only special rinse aid for dishwashers. 1. Open the door. The rinse aid compartment is located on the inside of the dishwasher door. 2. Press the release button on the rinse aid compartment. 3. Open the cover.
4. Pour rinse aid in slowly right up to the broken max line; this corresponds to a volume of approx. 140 ml when full. 5. Press the lid shut until it clicks into place. 6. Wipe up any spilt rinse aid with a cloth. Otherwise there will be too much foam when rinsing.
Setting the Amount of Rinse Aid Required
Only change the amount dispensed, if smears, milky spots (reduce the amount) or dried on water spots (increase the amount) can be seen on glasses and dishes. (See section If dishwashing results are not satisfactory.) The dosage can be set from 1-6. The dosage is pre-set to 4 in the factory. 1. Open the dishwasher door. 2. Press the release button on the rinse aid compartment. 3. Open the cover. 4. Set the dosage level. 5. Press the lid shut until it clicks into place. 6. If rinse aid has leaked out, wipe it away with a cloth.
Activating/Deactivating the Rinse Aid dispenser
If the 3 in1 button is pressed, you do not need to deactivate the rinse aid dispenser. 1. Press the ON/OFF button. If indicators for the programme buttons are lit, a dishwashing cycle is activated. The cycle must be deactivated: Press function buttons 2 and 3 simultaneously for approx. 2 seconds. All additional wash programme button indicators will go out. 2. Press function buttons 2 and 3 simultaneously and keep them pressed. The LED indicators for function buttons 1 to 3 will flash. 3. Press function button 2. The LED indicator for function button 2 will flash. The multi-display will indicate the current setting:
Rinse aid dispenser is deactivated Rinse aid dispenser is activated (factory setting)
4. Pressing function button 2 activates and deactivates the rinse aid dispensing function. 5. Once the multi-display is indicating the required setting, press the ON/ OFF button. The setting is now saved.
In daily use
Loading cutlery and dishes
Sponges, cleaning cloths and any other objects that can absorb water must not be washed in the dishwasher. Plastic and Teflon-coated dishes and pans tend to retain water droplets. These dishes and pans therefore do not dry as well as those made of china and stainless steel.
For washing in the dishwasher, the following cutlery/dishes/pots and pans are not suitable: Cutlery with wooden, horn, china or mother of pearl handles Plastic items that are not heat resistant Older cutlery with cement that is sensitive to temperature Dishes or cutlery with glued parts Pewter or copper items Lead crystal glass Steel items that rust Wooden boards/platters Items made from synthetic materials are of limited suitability: Only wash stoneware in the dishwasher if it is specifically marked by the manufacturer as being dishwasher-safe. Glazed patterns may fade if washed very frequently in the dishwasher. Silver and aluminium parts have a tendency to discolour during washing. Food remains, e.g. egg white, egg yolk and mustard often cause discoloration and staining on silver. Therefore always clean food residues from silver immediately, if it is not to be washed straight after use. Glass can become dull after a large number of washes.
Before loading the dishes, you should: Remove the worst of the food residues. Soak pans with burnt-on food residues. When loading the dishes and cutlery, please note: Dishes and cutlery must not impede the rotation of the spray arms. Load bowls, cups, glasses, pans, etc. with the opening downwards so that water cannot collect in them Dishes and items of cutlery must not lie inside one another or cover one another To avoid damage to glasses, they must not touch one another Dont put small items (e.g. lids) in the baskets for the dishes, but in the cutlery basket, so that they cant fall through the holes.
Warning: Sharp knives and other items of cutlery with sharp edges must be laid in the cutlery rack or in the upper basket to avoid the risk of injury. To ensure that all items of cutlery in the cutlery basket can be reached by the water, you should: 1.Place the grid insert on the cut- 2.Place forks and spoons in the lery basket cutlery basket's grid insert with their handles pointing downwards.
For larger utensils, such as whisks, leave off one half of the cutlery grid.
Pots, Pans, Large Plates
Load larger and heavily soiled dishes and pans in the lower basket. (Max. diameter for plates 29 cm).
To make it easier to load larger dishes, the two plate racks on the right in the lower basket can be folded down.
Cups, Glasses, Coffee Service
Load smaller, fragile crockery and long, sharp cutlery in the upper basket. Arrange items of crockery on and under the folding cup racks so that they are offset from each other and water can reach all items.
The cup racks can be folded up out of the way for tall crockery items. Lay or hang wine and brandy glasses in the slots in the cup racks.
Adjusting the Height of the Upper Basket
Maximum height of dishes in the Upper basket with upper basket raised with upper basket lowered 22 cm 24 cm Lower basket 30 cm 29 cm
The height of the baskets can also be adjusted when they are loaded. Raising/Lowering the Upper Basket 1. Pull out the upper basket completely. 2. Raise the upper basket as far as it will go and then lower it vertically. The upper basket will latch into the lower or the upper position.
Detergents remove the dirt from dishes and cutlery. The detergent must be added before the cycle starts.
1 to 2x
INTENSIVE CARE 70 4)
ECO 50 5)
Dinner service and cookware, normally soiled temperaturesensitive dishes
1) The consumption values were obtained under standardised conditions. They depend on how full the baskets for the dishes are. Variations are therefore possible in practice. 2) When using this cycle the degree of water clouding determines the amount of soiling on the dishes. The length of the cycle and water and energy consumption can vary greatly depending upon the load and how dirty the dishes are. Depending upon the soiling, the temperature of the water will be automatically adjusted to between 50C and 65C. 3) When using this cycle, only load the dishwasher half full. 4) During the final rinse, the temperature is increase to 68 for 10 minutes to disinfect e.g. babies bottles. 5) Test cycle for Test Institutes.
130 - 160
120 - 130
Starting a Dishwashing Cycle
1. Check that the spray arms can turn freely. 2. Turn the water tap on fully. 3. Close the door. 4. Press the ON/OFF button. 5. Select the desired cycle. The programme indicator comes on. The remaining time expected for the cycle will be shown in the multi-display. The selected cycle will begin after approximately 3 seconds. During the dishwashing cycle, the remaining time shown in the multidisplay may be adjusted according to the size of the load, degree of soiling, etc.
Interrupting or Cancelling a dishwashing cycle
Interrupt a dishwashing cycle that is in progress if it is absolutely necessary.
Interrupting the dishwashing programme by opening the dishwasher door Hot steam may escape when the door is opened. There is a risk of scalding.
1. Open the door carefully. The dishwashing cycle will stop. 2. Close the door. The cycle will continue. Cancelling the dishwashing cycle 1. Press function buttons 2 and 3 and keep them pressed. The programme display for the current cycle will flash for several seconds and then go out. 2. Release the function buttons. The dishwashing cycle has been cancelled. 3. If you want to start a new cycle, check whether there is any detergent in the dispenser. Turning off the dishwasher will only interrupt a selected dishwashing cycle, not cancel it. The cycle will recommence after turning the dishwasher back on again.
Setting the Delay Timer
With the delay timer you can delay the start of a dishwashing cycle for between 1 and 19 hours. 1. Press the Delay Timer button repeatedly until the multi-display shows the desired time delay, for example 12h, if the cycle is to start in 12 hours. The Delay Timer indicator is illuminated. 2. Select dishwashing cycle. 3. The time remaining to the start of the cycle is continuously displayed (e. g. 12h, 11h, 10h, 1h etc.). To change the time delay: As long as the cycle has not yet started, you can still change the setting by pressing the DELAY TIMER button. Cancelling the time delay: Press the Delay Timer button repeatedly until the length of the selected cycle appears in the multi-display. The selected dishwashing cycle will begin immediately. To change a dishwashing cycle As long as the cycle has not yet started, you can still change the dishwashing cycle. First cancel the dishwashing cycle, then re-set the time delay, lastly select the new dishwashing cycle.
Switching off the dishwasher
Do not switch off the dishwasher until the multi-display indicates 0 for the remaining cycle time. With some dishwashing cycles, the drying fan continues to run even after the end of the cycle. 1. Press the ON/OFF button. All display indicators will go out. 2. Turn off the water tap. Carefully open the door. Hot steam may escape. Hot dishes are sensitive to knocks. Therefore leave the dishes to cool for about 15 minutes before removing them. You also get a better drying result.
Removing the Dishes
It is normal for the inner door and the dispensers to be damp. Empty the lower basket first, then the upper basket. This way you avoid dripping water from the upper basket onto dishes in the lower basket. 21
Care and cleaning 1
Do not use furniture care products or aggressive cleaners. When necessary, clean the dishwashers controls with a soft cloth. Occasionally check the internal dispensers, door seal and water inlet filter (if fitted) for dirt and clean them, if necessary.
Cleaning the Filters
The filters must be regularly checked and cleaned. Dirty filters will spoil the wash results. 1. Open the door and remove the lower basket. 2. Turn the handle about of a turn anticlockwise (A) and remove the filter system (B). 3. Take hold of the coarse and fine filters (1/2) by the handle and remove them from the micro-filter (3). 4. Clean all filters thoroughly under running water. 5. Remove the flat filter (4) from the base of the washing compartment and clean both surfaces thoroughly. 6. Re-insert the flat filter. 7. Place the coarse and fine filters in the micro-filter and press together. 8. Insert the filter system in place and lock it by turning the handle clockwise as far as it will go. Ensure that the flat filter does not protrude above the base of the washing compartment. Under no circumstances may the dishwasher be used without its filters.
What to do if.
Remedying small malfunctions
If one of the following fault codes is displayed in the multi-display during operation: Fault code 10 (Problems with water inlet), Fault code 20 (Problems with water drainage), please have a look at the following table. When the fault is remedied, press the button for the cycle that has started. The cycle will continue. With other fault codes ( followed by a number): Abort the dishwashing cycle. Switch the appliance off and on again. Re-set the dishwashing cycle. If the fault is displayed again, please contact your local Service Force Centre and inform them of the fault code.
Malfunction Possible cause Water tap is blocked with limescale or faulty. The tap is turned off. Remedy Check the water tap and have it repaired if necessary. Turn the tap on.
The cycle indicator for the selected dishwashing cycle is flashing: fault code 10 is displayed in the multi-display: (Problems with water inlet)
The filter (where present) in Clean the filter in the the threaded hose fitting threaded hose fitting. on the tap is blocked. Press the button for the commenced dishwashing cycle; then abort the dishwashing cycle (see section: Starting a dishwashing cycle); clean filters (see section: Cleaning the filters).
Filters in the base of the dishwasher compartment are blocked.
Water inlet hose Check the position of the has not been correctly posihose. tioned.
Malfunction The cycle indicator for the selected dishwashing cycle is flashing, fault code 20 is displayed in the multi-display. (Problems with water drainage) Fault code 30 is displayed in the multi-display.
Possible cause The sink spigot connection is blocked.
Remedy Clean the sink spigot outlet.
Water drain hose Check the position of the has not been correctly posihose. tioned. First shut off the water tap, then switch off the appliance and contact the Customer Care Department. Plug in mains plug.
The anti-flood system has been triggered. The mains plug is not plugged in.
The cycle is not starting.
A fuse in the houses wiring Replace fuse. system is defective. For dishwasher models with If the dishes are to be a delay start timer: washed immediately, cancel A start time has been sethe delay start. lected.
The dishwashing compartment is made from rustfree stainless steel. Rust spots in the dishwashing compartment are due to Rust spots are visible in Only wash cutlery, dishes rust particles from external the dishwashing compartand pans that are suitable sources (rust particles from ment. for dishwasher use. water pipes, pans, cutlery, etc.). Remove such spots with a commercially-available stainless steel cleaning product. A whistling noise can be The whistling is not a cause Use a different brand of deheard when washing dishfor concern. tergent. es.
If the Dishwashing Results are not Satisfactory
The dishes are still dirty. The wrong dishwashing cycle was selected. The dishes were loaded is such a way that the dishwashing water did not reach all items. The baskets for the dishes must not be overloaded. The filters in the base of the washing compartment are dirty or incorrectly positioned. Good quality detergent was not used, or too little was used. In the case of scale deposits on the dishes: The dishwasher salt dispenser is empty or the water softening system has been incorrectly set. The drain hose is incorrectly positioned. The dishes do not dry and are not shining. Poor quality rinse aid was used. The rinse aid dispenser is empty. There are smears, streaks, milky spots or a shiny bluish coating on glasses and dishes. Lower rinse aid dosage. There are dried water drops on the glasses and dishes. Increase rinse aid dosage. The detergent may be the cause. Contact the detergent manufacturer's customer advice centre. Glass corrosion Contact the detergent manufacturer's customer advice centre.
Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at your local waste disposal facilities. Old appliance Please dispose of your old appliance in line with the guidelines for disposal in your area. Warning! When your appliance has finished its working life, remove the plug from the socket. Cut off the cable and plug and dispose of them. Break the door lock so that the door no longer shuts. This prevents children from trapping themselves inside and endangering their lives.
Capacity: Permitted water pressure: Electrical connection: 12 place settings including serving dishes 1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa) Information on the electrical connection is given on the rating plate located on the right inner edge of the dishwasher door.
Dishwasher: Free-standing appliances Dimensions: Max. weight: 850 x 598 x 598 (H x W x D in mm) 54 kg
This appliance conforms with the following EU Directives: 73/23/EEC dated 19.02.1973 Low Voltage Directive 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive 92/31/EEC 93/68/EEC dated 22.07.1993 CE Marking Directive
Notes for Test Institutes
Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test cycle (see Cycle Table). Tests in accordance with EN 50242 must be carried out when the salt dispenser in the water softener and the rinse aid dispenser have been filled with salt and rinse aid respectively, and using the test cycle (see Cycle Table).
Full load: 12 place settings including serving dishes Amount of detergent required: 5g + 25g (Type B) Rinse aid setting: Upper basket *) 4 (Type III) Half load: 6 place settings including serving dishes, leaving alternate positions in the rack free 20g (Type B) 4 (Type III)
Sample loading arrangements:
*) If necessary, move the cup rack from right to left. When doing this, ensure that the cup rack is at the same height.
Lower basket with cutlery basket
Installation and connection instructions 1 Safety Information for the Installation
Only transport the dishwasher in an upright position, otherwise salt water may run out. Before using the dishwasher for the first time, check for any damage caused in transport. Do not under any circumstances connect an appliance that is damaged. In the case of damage, please contact your supplier. Never use the dishwasher if the mains cable, water inlet or drain hose are damaged; or if the control panel, work top or plinth area are damaged such that the inside of the appliance is freely accessible. Always plug the mains plug into a correctly installed shockproof socket. Permanent connection: a permanent connection must only be installed by a trained electrician. Prior to using the appliance for the first time, ensure that the rated voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating is also to be found on the rating plate. Multi-way plugs / connectors and extension cables must not be used. This could constitute a fire hazard through overheating. The dishwashers cable must only be replaced by a Service Force Engineer. A water inlet hose with safety valve must only be replaced by a Service Force Engineer.
Installing the Dishwasher
The dishwasher must be installed on a firm floor and adjusted to ensure that it is stable and level in all directions. To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units, extend the threaded feet using a screwdriver. The drain hose, inlet hose and mains cable must be laid so that they are able to move freely within the plinth area, and so that they are not kinked or crushed when the dishwasher is in position. The dishwasher must also be screwed tightly to the work surface or to the adjoining units. This is essential to ensure the dishwasher does not tip up.
If the dishwasher is installed directly next to a cooker, a heat-insulating, non-flammable panel (laminated with aluminium foil on the side next to the cooker) must be fitted flush with the top edge of the work surface (depth 57.5 cm). If the appliance is built-in under a kitchen work surface, the worktop supplied with the dishwasher can be removed in the following way: 1. Unscrew the screws from the elbows at the rear (1). 2. Push the appliances worktop backwards about 1 cm (2).
3. Lift the worktop at the front (3) and remove it.
If the dishwasher is later used as a free-standing appliance, the work surface supplied with it must be re-mounted. The plinth on free-standing appliances is not adjustable.
Connecting the dishwasher
Connecting to the water supply
The dishwasher can be connected to cold and hot water supplies up to max. 60C. The dishwasher must not be connected to open hot water appliances or instantaneous water heaters.
Permitted water pressure
Lowest permitted water pressure: 1 bar (=10 N/cm2 =100 kPa) Highest permitted water pressure: 10 bar (=100 N/cm2 =1 MPa) Consult your plumber if the water pressure is less than 1 bar. If the water pressure is greater than 10 bar, a pressure reduction valve must be used (available from your dealer).
Connecting the inlet hose
The water inlet hose must not be kinked, crushed or entangled when it is being connected. Connect the threaded hose fitting (ISO 228-1:2000) on the water inlet hose to a tap with an external thread ( inch). The inlet hose is fitted with either a plastic or a metal nut: Only tighten the plastic nut hand tight. You must tighten the metal nut using a tool. Then do a visual check for water tightness (make sure that the tap is not dripping). So that access to the tap in the kitchen is not restricted by the use of the dishwasher, we recommend installing an additional tap, or fitting a T-branch to the existing tap. If you need a longer water inlet hose than that supplied, the following VDE-approved complete hose sets are to be used. These are available from your local service centre.
Drain hose The drain hose must not be kinked, crushed or entangled. Connecting the drain hose: Maximum permitted height: 1 metre. Minimum required height: 40 cm above the bottom edge of the appliance. Extension hoses Extension hoses are available from your local Service Force Centre. To ensure that the function of the appliance is not impeded, the internal diameter of extension hoses must be 19 mm. Extension hoses must not be laid more than a maximum distance of 3 metres horizontally; the maximum permitted height for the connection for the drain hose is then 85 cm. Sink outlet connection The outlet of the drain hose ( 19 mm) fits all commonly available sink outlet types. The outer diameter of the sink outlet connection must be at least 15 mm. The drain hose must be fixed to the sink outlet connection using the hose clamp supplied. Water drainage if the dishwasher is built-in at high level If the dishwasher is installed at a high level, and the drain hose connection is less than 30 cm from the lower edge of the appliance, adapter kit ET 111099520 must be fitted by your local Service Force Centre.
Water drainage into sink (only possible with free-standing appliances) If you wish to hang the drain hose over the edge of a sink, use a detachable hose elbow. You can obtain this from AEG Service Force by referring to spare part number ET 190. 1. Fit the elbow to the drain hose. 2. Secure the drain hose so that it cannot slide off the edge of the sink. Pass a piece of cord through the hose elbow and fix it to the wall or the tap. 33
For protection from water damage, the dishwasher is equipped with a anti-flood system. In the event of a fault, the safety valve in the water inlet hose immediately interrupts the supply of water to the appliance and the drain pump is activated. In this way water can neither escape nor overflow. The remaining water in the appliance is automatically pumped out.
Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING - This appliance must be earthed. The manufacturer declines any responsibility should these safety measures not be observed. Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. To isolate the dishwasher from the mains, remove the mains plug. Important: The plug must still be accessible after the appliance has been installed.
Changing a fuse
The appliance is supplied with a 13amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13amp ASTA approved (BS 1363A) fuse must be used. Green & Yellow Should the plug need to be replaced for any reason, proceed as described below. The wires on the mains lead are coloured in accordance with the following code. Green and Yellow: Earth Blue: Neutral Brown: Live
The wire coloured green and yellow must be connected to the terminal marked with the letter E or by the earth symbol or coloured green and yellow.
The wire coloured blue must be connected to the terminal N or coloured black. The wire coloured brown must be connected to the terminal marked L or coloured red. Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath. WARNING! A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that, if it is necessary to cut off the plug, it is disposed of safely and not retained.
The water inlet hose, drain hose and the mains cable must all be connected to the side of the dishwasher as there is no space for them behind the appliance.
2 connection pieces 45 or straight, outer 19 mm, length 30 mm doublevalve waterdrainage waterinlet
watermains socket drainage
Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate. The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's operating and maintenance instructions. The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. All service work under this guarantee must be undertaken by a Service Force Centre. Any appliance or defective part replaced shall become the Company's property. This guarantee is in addition to your statutory and other legal rights. Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours in which case a premium will be charged. Exclusions This guarantee does not cover: Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable parts of glass or plastic. Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom. Appliances found to be in use within a commercial environment, plus those which are subject to rental agreements. Products of AEG manufacture which are not marketed by AEG. European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications: The guarantee starts from the date you first purchased your product. The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products. This guarantee relates to you and cannot be transferred to another user. Your new home is within the European Community (EC) or European Free Trade Area. The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal household. The product is installed taking into account regulations in your new country. Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Germany Italy Sweden UK Senlis Nrnberg Pordenone Stockholm Slough +33 (0) 29 +49 (0) 7378 +39 (0) +46 (0) 5360 +44 (0) 1753 219899
Service and Spare Parts
If the event of your appliance requiring service, or if you wish to purchase spare parts, please contact Service Force by telephoning: Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce.co.uk Before calling out an engineer, please ensure you have read the details under the heading What to do if. When you contact the Service Force Centre you will need to give the following details: 1. Your name, address and post code. 2. Your telephone number. 3. Clear and concise details of the fault. 4. The model and serial number of the appliance (found on the rating plate) 5. The purchase date. Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee service calls. Customer Care For general enquiries concerning your AEG appliance, or for further information on AEG products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.aeg.co.uk. Customer Care Department For Customer Service in the Republic of Ireland please contact us at the adAEG Domestic Appliances dress below: 55-77 High Street AEG/ Electrolux Group (Ire) Ltd Slough Long Mile Road/ Dublin 12 Berkshire, SL1 1DZ Republic of Ireland Tel: (*) Tel: +353 (0) Email: email@example.com (*) Calls may be recorded for training purposes 39
From the Electrolux Group. The worlds No.1 choice.
The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
AEG Hausgerte GmbH Postfach 1036 D-90327 Nrnberg http://www.aeg.hausgeraete.de Copyright by AEG 158-00-140504-02 Subject to change without notice
Optra C710 MP540 TA-4650 HBF600T RC-995 48261 SX1 IS FF-1000LTC Spider 2000 HR-V210E AR-5015 Instamedia Microwave Oven Chorus 7 WMS CT-WN4322Z VR600 Smartboard 6955 W SC-PT860 DM1002X Trekko Mouse Ensoniq SQ-2 RE-10202 VS-840EX Easycord HT-TX715 UE-37C6820 NAD S300 DSR-2000-DSR-1000 Digitech RP55 RX-DT39 RZ-20LA90 Syncmaster 244T PS-50Q91H Proheat 7950 Microverb3 RC-50 Rx-d206 IP-901 WA10B3 Kodak C713 XRS9930 Citroen C6 CDX-M7810 WFH1677F 66 Maps DS18dsal Keyboard GSA-4160B RCR 128 DVD-HD745 WV-CL930 CN-NVD905U RQ-SX65F Delonghi EC7 26PF7321 LCD-LB030 945GM3 SPP-S2730 Envoy-2004 NN-3496 MAX-VS990 Inspiron 9400 RX620 NX7000 2440S PLM-A55 Tahoe 1999 B1315J HD501LJ-jp1 Allergy 286 336 SRU9400 MC-7826M LK45C Review CHC-CL1 Cleaner DSP-E200 KX-TG8012NE B-405-B-205 CMD-Z5 Dvdr77-17B RDC-7 1 Digital GT102D Satellite 2540 SCX-4824fnkg NX-U10 Queens MP56 Navigon 12XX Ssleq Argos System Orchestro 889 Makita 6501 F3000 NVD-T334 URG E
manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101