Pagina 9

Audible signals
Audible signals have been introduced to help indicate which operations the dishwasher is performing: "Setting of the water softener" "End of programme" "Something not working with the machine"
Deactivation/activation of the audible signals
(The dishwasher must be switched off) 1. Press the On/Off button. All programme selection buttons indicator lights will illuminate (setting mode). If only one programme selection button indicator light is illuminated, this means that a washing programme has been selected. The programme must be cancelled: press simultaneously the function buttons 2 and 3 for about 2 seconds, the indicator light of the set programme button starts flashing for about 2 seconds. After about 2 seconds the indicator lights of all the programme selection buttons will illuminate indicating that the set programme has been cancelled and that the machine is now in setting mode. 2. Press simultaneously function push buttons 2 and 3, the indicator lights of the function push buttons 1, 2 and 3 start flashing. 3. Press the function button 3, the indicator lights of function buttons 1 and 2 turn off while the indicator light of the button 3 goes on flashing, the digital display indicates the current setting. Audible signals deactivated Audible signals activated (factory set) 4. To change the current setting, press again the function button 3, the digital display will indicate the new setting. 5. To memorise the operation, switch off the dishwasher by pressing the On/Off button or wait about 60 seconds after which the dishwasher will automatically return to setting mode.

Pagina 10

Prior to using for the first time
Before using your dishwasher for the first time: 1. Ensure that the electrical and water connections comply with the installation instructions 2. Remove all packaging from inside the appliance 3. Set the water softener 4. Pour 1 litre of water inside the salt container and then fill with special dishwasher salt. 5. Fill the rinse aid dispenser.
Setting the water softener
The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance. The higher the content of these minerals and salts, the harder your water is. Water hardness is measured in equivalent scales, German degrees, French degrees and mmol/l (millimol per litre). The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority can advise you on the hardness of the water in your area. The water softener must be set in both ways: manually, using the water hardness dial and electronically, using the function push buttons on the control panel.

Water hardness dH

(german degrees)

mmol/l

(french degrees) (millimol per litre, international unit for the hardness of water)
Level indicaNumber ted in the of audible digital dissignals Manually Electronically play 1

no salt necessary

Adjusting the water hardness setting
51 - - - - - - - - - 10 <4
91 - - - - - - - - - 18 <7
9,0 - 12,5 7,6 - 8,9 6,5 - 7,5 5,1 - 6,4 4,0 - 5,0 3,3 - 3,9 2,6 - 3,2 1,9 - 2,5 0,7 - 1,8 < 0,7

III II I/II I

Pagina 11

a) Setting manually

1. Open the dishwasher door. 2. Remove the lower basket from the dishwasher. 3. Turn the water hardness dial to position 1 or 2 (see table). 4. Replace the lower basket. The dishwasher is factory set at position 2.
b) Setting electronically
(The dishwasher must be switched off) The dishwasher is factory set at level 5. 1. Press the On/Off button. All programme selection buttons indicator lights will illuminate (setting mode). If only one programme selection button indicator light is illuminated, this means that a washing programme has been selected. The programme must be cancelled: press simultaneously the function buttons 2 and 3 for about 2 seconds, the indicator light of the set programme button starts flashing for about 2 seconds. After about 2 seconds the indicator lights of all the programme selection buttons will illuminate indicating that the set programme has been cancelled and that the machine is now in setting mode. 2. Press simultaneously function buttons 2 and 3, until the indicator lights of function buttons 1, 2 and 3 start flashing. 3. Press function button 1, the indicator lights of function buttons 2 and 3 turn off while the indicator light of the button 1 goes on flashing, the digital display indicates the current level and a sequence of intermittent audible signals are heard. The current level is indicated by the number visible in the display and the number of intermittent audible signals heard. Example: displayed + 5 audible signals = level 5.

Pagina 12

4. To change the level, press button 1. Each time the button is pressed the level changes. (For the selection of the new level see the chart). Examples: if the current level is 5, by pressing button 1 once, level 6 is selected. if the current level is 10, by pressing button 1 once, level 1 is selected. 5. To memorise the operation, switch off the dishwasher by pressing the On/Off button or wait about 60 seconds after which the dishwasher will automatically return to setting mode.

Pagina 13

Filling with salt
Only use salt specifically designed for use in dishwashers. All other types of salt not specifically designed for use in a dishwasher, especially table salt, will damage the water softener. Only fill with salt just before starting one of the complete washing programmes. This will prevent any grains of salt or salty water, which may have been spilt, remaining on the bottom of the machine for any period of time, which may cause corrosion.

To fill:

1. Open the door, remove the lower basket and unscrew the cap of the salt container by turning it anticlockwise. 2. Pour 1 litre of water inside the container (this is necessary only before filling with salt for the first time). 3. Using the funnel provided, pour in the LE SA UT salt until the container is full. ZO LT SA LZ 4. Replace the cap making sure that SA L SE there is no trace of salt on the screw thread or on the gasket. 5. Screw on the cap tightly turning it clockwise until it stops with a click.
The salt container will require topping up periodically. You are reminded of this by the salt indicator light on the control panel which comes on when the salt has finished. The salt indicator light on the control panel can remain illuminated for 2-6 hours after the salt has been replenished, assuming the dishwasher remains switched on. If you are using salts that take longer to dissolve then this can take longer. The function of the machine is not affected. Do not worry if water over flows from the unit when filling with salt, this is quite normal.

Pagina 14

Rinse aid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying. The dispenser, which is positioned inside the door, holds about 110 ml of rinse aid, which is sufficient for 16 - 40 dishwashing programmes, depending upon the dosage setting.

Filling with rinse aid

1. Open the container by pressing the release button (A). 2. Add the rinse aid until the container is completely full. The maximum level for filling is indicated by max.
Ensure that the lid is closed after every refill. Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash. Only use branded rinse aid for dishwashers. Never fill the rinse aid dispenser with any other substances (e.g. dishwasher cleaning agent, liquid detergent). This would damage the appliance.

Pagina 15

Adjusting the dose
According to the finish and drying results obtained, adjust the dose of rinse aid by means of the 6 position selector (position 1 minimum dosage, position 6 maximum dosage). The dose is factory set in position 4. Increase the dose if there are drops of water or lime spots on the dishes after washing. Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or knife blades.
Top up the rinse aid when the indicator light on the control panel illuminates.

Pagina 16

If you are using dishwasher detergent that already contains rinse aid, the detergent including the rinse aid must be placed in the detergent compartment. In this case the rinse aid dispenser must be deactivated in order to avoid a double dosage.

Pagina 21

The upper basket
The upper basket is designed for plates (dessert plates, saucers, dinner plates up to 24 cm in diameter), salad bowls, cups and glasses; these should be arranged as shown in the pictures. Glasses with long stems can be placed upside-down in the raised cupracks. The cup-rack on the left folds upwards to increase your loading flexibility. Arrange items on and underneath the fold-down cup racks so that water can reach all surfaces. Light items (plastic bowls etc.) must be loaded in the upper basket and arranged so they do not move.
Before closing the door, ensure that the spray arms can rotate freely.

Pagina 22

Adjusting the height of the upper basket
If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position.
Maximum height of the dishes in: upper basket lower basket With upper basket raised With upper basket lowered 20 cm 24 cm 31 cm 27 cm
To move to the higher position proceed as follows:
1. Pull out the basket until it stops 2. Carefully lift both sides upwards until the mechanism is engaged and the basket is stable. Attention! Never lift or lower the basket on one side only. When the basket is in the higher position you will not be able to use the cup rack(s).
To lower the basket to the original position
1. Pull out the basket until it stops 2. Carefully lift both sides upwards and then allow the mechanism to drop back down slowly, keeping hold of it. After loading your machine always close the door, as an open door can be a hazard.

Pagina 23

Use of detergent
Only use detergents specifically designed for use in dishwashers. We recommend the use of Finish detergents. Using no more then the correct amount of detergent contributes to reducing pollution. Prior to the start of a wash programme (not for the Rinse and Hold programme). The detergent is released during the washing phase. Please observe the manufacturers dosing and storage recommendations as stated on the detergent packaging.

Fill with detergent

1. If the lid is closed: press release button (1). The lid springs open. 2. Fill the detergent dispenser (2) with detergent. The marking indicates the dosing levels: 20 = approximately 20 g of detergent 30 = approximately 30 g of detergent
3. All programmes with prewash need an additional detergent dose (5/10 g) that must be placed in the prewash detergent chamber (3). This detergent will take effect during the prewash phase. 4. Close the lid and press until it locks in place.

For best results we recommend the use of Finish detergents, rinse aid and salt.

PO RI G U N

DOUBLE

ACTION

BRILLIANT RILLIANT SHINE

F RA O

LIQUID GEL

P O W D E R

C O N C E N T R AT E D D I S H WA S H E R D E T E R G E N T

Pagina 26

Washing programmes
Cycle description Programme Type of load Degree of soil Main wash Pre-rinse Consumption values1 Duration (minutes)

Energy (kWh)

AUTOMATIC (50 - 65)

Crockery and cutlery

Normal soil

1/2x - - 2x

80 0,105 1,25 0,30 0,105 1,115 1,160 0,170 0,80 13

30 MIN. (60)

Light soil

INTENSIV 70

Crockery, cutlery, pots and pans

Heavy soil

ECO 50 2
(1) The consumption values were obtained under standardised conditions. They depend on how full the baskets for the dishes are. Variations are therefore possible in practice. (2) Testing programme for EN 50242 (see "Hints for Test Centres). This programme, developed for the use of detergents with enzymes, allows you to achieve, with reduced consumption of energy the same cleaning results that would otherwise be obtained only with the 65C programmes and conventional detergents. To compensate the lower temperature, the duration of washing and drying have been extended.
"AUTO" washing programme
During the "AUTO" washing programme the amount of soil on the dishes is determined by how cloudy the water is. If the appliance is partially loaded and the dishes lightly soiled, the "prewash"", main wash", and "rinse" phases of the programme are shorter and the water consumption level is lower. If the appliance is fully loaded and the dishes heavily soiled, the "prewash"", main wash", and "rinse" phases of the programme are longer and the water consumption level is higher. For this reason the programme duration, water and energy consumption levels can vary within the stated range for AUTO programme (see "Washing programmes chart"). During the "AUTO" programme the temperature of the main wash water is also automatically adjusted between 50C and 65C depending on the amount of soil on the dishes.

Water (litres)

Intermediate

Final rinse

Drying

Pagina 27

Starting a washing programme
In this fully integrated appliance the controls are located on the top of the door. When selecting a programme, the door needs to be open.
1. Check that the baskets have been loaded correctly and that the spray arms can rotate freely 2. Turn on the water tap 3. Press the On/Off button

Open the dishwasher door. The remaining delay time before the start of the programme is visible in the digital display. Press simultaneously the function buttons 2 and 3 for about 2 seconds. After about 2 seconds the indicator lights of all the programme buttons will illuminate indicating that the delay start in progress has been cancelled and that the machine has returned to setting mode.

Pagina 29

With the cancelling of the delay start also the set programme has also been cancelled. Set the washing programme again.
7. End of the washing programme
The dishwasher will automatically stop and an audible signal informs you of the end of the washing programme. The point-shaped optical signal disappears on the floor beneath the appliances door. Do not open the dishwasher door before this optical signal turns off. If the door is not immediately opened at the end of the programme, air will circulate inside the dishwasher to prevent residual steam recondensing on the dishes as water droplets. This device operates intermittently for about 20 minutes, as long as the dishwasher is switched on. If the On/Off button is pressed or the door is opened during these 20 minutes, the device will be automatically cancelled. Hot steam may escape from the appliance when opening the door immediately after the end of the programme, therefore, open the door carefully. The end of programme indicator light is illuminated. Switch off the dishwasher by pressing the On/Off button.
8. Unloading the dishwasher
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down before removing from the appliance. Empty the lower basket first and then the upper one; this will avoid water dripping from the upper basket onto the dishes in the lower one. Water may appear on the sides and the door of the dishwasher as the stainless steel will eventually become cooler then the dishes. When the washing programme has finished, it is recommended that the dishwasher is unplugged and the water tap turned off.

Pagina 30

Maintenance and cleaning
Clean the external surfaces of the machine and control panel with a damp soft cloth. If necessary use only neutral detergents. Never use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc.). Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned regularly with a damp cloth. We recommend every 3 months to run a 65C wash programme without dishes using detergent.

Cleaning the filters

The filters must be checked and cleaned from time to time. Dirty filters will degrade the washing result. 1. Open the door, remove the lower basket. 2. The dishwashers filter system comprises a coarse (A/B), a microfilter (C) and a flat filter (D). Some dishwasher will only have a coarse filter (A), a microfilter (C) and a flat filter (D). Unlock the filter system using the handle on the microfilter, and remove.
3. Turn the handle about 1/4 a turn anticlockwise and remove.

Pagina 31

4. Take hold of the coarse/fine filter (A/B) by the handle with the hole and remove from the microfilter (C). 5. Clean all filters thoroughly under running water. 6. Remove the flat filter (D) from the base of the washing compartment and clean both faces thoroughly.
7. Put the flat filter (D) back in the base of the washing compartment. 8. Place the coarse/fine filter (A/B) in the microfilter (C) and press together. 9. Put the filter combination in place and lock by turning the handle clockwise to the stop. During this process ensure that the flat filter does not protrude above the base of the washing compartment. Under no circumstances may the dishwasher be used without filters. Incorrect repositioning and fitting of the filters will produce poor washing results. NEVER try to remove the upper spray arm. If residues of soil have clogged the holes in the upper spray arm, remove them with a toothpick.

Pagina 32

Prolonged periods of non-operation
If you are not using the machine for any period of time you are advised to: 1. Unplug the appliance and then turn off the water. 2. Leave the door ajar to prevent the formation of any unpleasant smells. 3. Leave the inside of the machine clean.

Frost precautions

Avoid placing the machine in a location where the temperature is below 0C. If this is unavoidable, empty the machine, close the appliance door, disconnect the water inlet pipe and empty it.

Moving the machine

If you have to move the machine (moving house etc.): 1. Unplug it. 2. Turn the water tap off. 3. Remove the water inlet and discharge hoses. 4. Pull the machine out together with the hoses. Avoid over tilting the machine during transportation.

Pagina 33

What to do, when.
Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the instructions given here, without calling out an engineer.
.a flashing fault code appears
The dishwasher will not start or stops during operation. The intervention of an alarm is indicated by an intermittent audible signal and, if your appliance is equipped with an optical floor signal, in the event of an error a dot-shaped optical signal will flash on the floor: open the dishwasher door, a fault code is visible in the digital display (see following chart). Carry out the following suggested corrective actions.
Fault code / Malfunction in the digital display appears Possible cause The water tap is blocked or furred with limescale. The water tap is turned off. The machine does not fill with water The filter (where present) in the threaded hose fitting at the water inlet valve is blocked. The water inlet hose has not been correctly laid or it is bent or squashed. in the digital display appears The sink spigot connection is blocked. The water drain hose has not been correctly laid or it is bent or squashed. Protection against flooding is active. Solutions Clean the water tap. Turn the water tap on. Clean the filter in the threaded hose fitting.
Check the water inlet hose connection. Clean out the sink spigot connection. Check the water drain hose connection.
The dishwasher will not drain in the digital display appears
Close the water tap and contact your local Service Force Centre.
Once the checks have been carried out, to continue the programme press the button of the programme that was running before the intervention of the alarm and close the door. The programme will continue from the point in which it was interrupted. If the fault code reappears contact your local Service Force Centre. For other combinations of fault codes not described in the above chart will appear, please contact your local Service Force Centre. 33

Pagina 34

.there are problems when operating the dishwasher
Fault Possible cause The dishwasher door has not been properly closed. The programme does not start The main plug is not plugged in. The fuse has blown in the household fuse box. For dishwasher models with delay start option: Delay start has been selected. There is a whistling noise during washing The whistling is not a cause for concern. Solutions Close the door. Insert the mains plug. Replace the fuse. If dishes are to be washed immediately, cancel the delay start. Use a different brand of detergent.

Pagina 35

.the wash results are not satisfactory

The dishes are not clean

The wrong washing programme has been selected. The dishes were arranged in such a way as to stop water reaching all parts of the surface. The baskets must not be overloaded. The spray arms do not rotate freely due to wrong arrangement of the load. The filters in the base of the washing compartment are dirty or incorrectly positioned. Too little or no detergent has been used. Where there are limescale deposits on the dishes; the salt container is empty or the wrong level of the water softener has been selected. The drain hose connection is not correct. The salt container cap is not properly closed.
The dishes are wet and dull
Rinse aid was not used. The rinse aid dispenser is empty.
There are streaks, milky spots or a bluish coating on glasses and dishes
Decrease rinse aid dosing.
Water drops have dried onto glasses and dishes
Increase rinse aid dosing. The detergent may be the cause. Contact the detergent manufacturers consumer care line.

Pagina 36

Service
In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local AEG Service Force Centre by telephoning
Your call will be automatically routed to the Service Centre covering your post code area. For the address of your local Service Force Centre and further informations about Service Force, please visit the website at www.serviceforce.co.uk Help us to help you Please determine your type of enquiry before writing or telephoning. When you contact us we need to know, 1 Your name, address and post code 2 Your telephone number RAClear and concise details of the fault code 4 Date of purchase 5 PNC (product number) S.N. (serial number) This information can be found on the rating plate located on the right inside edge of the door.

Mod. o. Prod.N. Ser. No.

Customer Care
For general enquiries concerning your AEG appliance, or for further information on AEG products, you are invited to contact our Customer Care Department by letter or telephone at the address below or visit our website at www.aeg.co.uk Customer Care Department AEG Domestic Appliances 55-77 High Street Slough Berkshire SL1 1DZ Tel.: (*) * calls to this number may be recorded for training purposes 36

Pagina 37

Guarantee terms

Guarantee conditions

Standard Guarantee Conditions
We, AEG, undertake that if within 12 months of the date of purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate. The appliance has been used for normal domestic purposes only, and in accordance with the manufacturers instructions. The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not authorised by us. All service work under this guarantee must be undertaken by a Service Force Centre. Any appliance or defective part replaced shall become the Companys property. This guarantee is in addition to your statutory and other legal rights. Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours in which case a premium will be charged.

Exclusions

This guarantee does not cover: Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable parts of glass or plastic. Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom. Appliances found to be in use within a commercial environment, plus those which are subject to rental agreements. Products of AEG manufacture which are not marketed by AEG.

Pagina 38

European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications: The guarantee starts from the date you first purchased your product. The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products. This guarantee relates to you and cannot be transferred to another user. Your new home is within the European Community (EC) or European Free Trade Area. The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal household. The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliance. France Germany Italy Sweden UK Senlis Nurnberg Pordenone Stockholm Slough +33 (0) +49 (0) 7378 +39 (0) +46 (0) +44 (0)1753 219899

Pagina 39

Dimensions: Width Height Max depth Max depth with open door 44.6 cm 81.8 - 87.8 cm 55.5 cm 114 cm
Electrical connection: Voltage Overall power Fuse Water supply pressure: Capacity:
Information on the electrical connection is given on the rating plate on the inner edge of the dishwashers door.

Minimum Maximum

50 kPa (0.5 bar) 800 kPa (8 bar) 9 place settings
This appliance complies with the following E.E.C. Directives: - 73/23 or 19.2.73 (Low Voltage Directive) and subsequent modifications; - 89/336 or 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.

Pagina 40

Any electrical and/or plumbing work required to install this appliance should be carried out by a qualified electrician and/or plumber or competent person. Remove all packaging before positioning the machine. If possible, position the machine next to a water tap and a drain.

Building-in

This dishwasher is designed to be fitted under a kitchen counter or worksurface. Attention! Carefully follow the instructions on the enclosed template for building in the dishwasher and fitting the furniture panel. No further openings for the venting of the dishwasher are required, but only to let the water fill and drain hose and power supply cable pass through. The dishwasher incorporates adjustable feet to allow the adjustment of the height. During all operations that involve accessibility to internal components the dishwasher has to be unplugged. When inserting the machine, ensure that the water inlet hose, the drain hose and the supply cable are not kinked or squashed.

Levelling

Good levelling is essential for correct closure and sealing of the door. When the appliance is correctly levelled, the door will not catch on either side of the cabinet. If the door does not close correctly, loosen or tighten the adjustable feet until the machine is perfectly level.
Fixing to the adjacent units
The dishwasher must be secured against tilting. Therefore make sure that the counter it is fixed under, is suitably secured to a fixed structure (adjacent kitchen units cabinets, wall).

Pagina 41

Water supply connections
For making the connection itself, the coupling nut fitted to the machines supply hose is designed to screw onto either a 3/4" inch gas thread spout. The water pressure must be within the limits given in the "Technical specifications". Your local Water Authority will advise you on the average mains pressure in your area. The water inlet hose must not be kinked, crushed, or entangled when it is being connected up. The dishwasher features fill and drain hoses which can be turned either to the left or the right to suit the installation by means of the locknut. The locknut must be correctly fitted to avoid water leaks. A (Attention! NOT all models of dishwashers have fill and drain hoses provided with locknut. In this case, this kind of facility is not possible). If the machine is connected to new pipes or pipes which have not been used for a long time, you should run the water for a few minutes before connecting the inlet hose. Do not use, for connection, old hoses which have been used with another appliance. The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations.

Pagina 42

Water inlet hose with safety valve
After connecting the double-walled water inlet hose, the safety valve is next to the tap. Therefore the water inlet hose is only under pressure while the water is running. If the water inlet hose starts to leak during this operation, the safety valve cuts off the running water.
Please take care when installing the water inlet hose:

This appliance must be earthed. The manufacturer declines any responsibility should this safety measure not be observed. Warning! A cut-off plug inserted into a 13amp socket is a serious safety (shock) hazard. Ensure that the cut-off plug is disposed of safely. 44

Pagina 45

Hints for test centres
Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme (see "Washing programmes" chart). Testing in accordance with EN 60242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme (see "Washing programmes" chart).
Load: Rinse aid setting Detergent dosage: 9 standard place settings Position 4 (type III) 5 g + 20 g (type B)
Arrangement upper basket: without smaller bowl and salad-bowl
Arrangement upper basket: with smaller bowl and salad-bowl

Arrangement lower basket

Arrangement cutlery basket Cup racks: position A

Pagina 46

Pagina 47

Pagina 48

F rom the Electrolux Group. The worlds No.1 choice.
The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. 14 billion USD in more than 150 countries around the world.

AEG Hausgerte GmbH

Postfach 1036 D-90327 Nrnberg http://www.aeg.hausgeraete.de Copyright by AEG
Subject to change without notice