IKN KN IK QLH IKN QLH JMO JMO IKN

Before the first wash

1. Open the detergent drawer. 2. Pour approx. 1 litre of water through the detergent drawer into the washing machine. This closes the water container when the next programme is started and the economy valve can function properly 3. To remove any production-related residues from the drum and water tank, perform the first wash cycle without a load. Programme: COTTONS/LINEN 60, press the TIME SAVER button, add approx. 1/4 measuring cup of detergent.
Preparing and sorting washing
Preparing washing Empty the pockets. Remove foreign bodies (e.g. coins, paper clips, nails, etc.). Do up zips, button up covers to prevent damage to washing. Remove the runners from net curtains or cover them with a net or a bag. Wash delicate and small items in a net/pillowcase, e. g. net curtains, tights, small socks, handkerchiefs, bras. Important: Bras and other items containing wires should only be washed in a net bag. The wires can work loose and damage the appliance. Sorting washing By colour: Wash white and coloured washing separately. Washing can run. By temperature, type of washing and care symbol. Important: Do not wash fabrics with the G care symbol (= do not wash!) in the washing machine.

Running a wash cycle

Opening the door/loading washing
1. Open the door: pull the handle on the door. When the appliance is switched on, the DOOR and START/PAUSE indicators show whether the door can be opened:
DOOR indicator illuminated green illuminated green illuminated red or not illuminated START/PAUSE indicator flashing red or not illuminated illuminated red flashing red or illuminated red Can the door be opened? yes yes, after pressing the START/PAUSE button no, water level and/or temperature too high
2. Separate washing and load it loosely. Mix large and small items. Important: Do not get any washing caught between the door and the rubber seal. 3. Firmly push the door shut. Door catch must audibly click shut.
Adding detergent /conditioner
Important: Only use detergents/conditioners that are suitable for use in household washing machines. Add detergent/conditioner in accordance with the detergent/conditioner manufacturers instructions. Observe instructions on the packaging. The amount of detergent used depends on: the degree of soiling, the load size the hardness of the tap water. If the manufacturer does not make any recommendations with regard to small volumes of washing: For a half-load use a third less, and for a very small load use only the half the amount of detergent that is recommended for a full load.

Water softener should be used from water hardness range 2 (=medium). The amount of detergent used can then always be that as for hardness range 1 (=soft). Your local water company will provide you with information about water hardness in your area. 1. Pull out the detergent drawer as far as it will go. 2. Add the detergent/conditioner. 3. Push the detergent drawer in fully.
Washing powder/tablets for the main wash cycle Conditioner/Wash-care products to preserve the shape of garments/Starch
Stain removal agent/ stain removal tablets Washing powder/tablets for the pre wash cycle or water softener
Washing powder/tablets for the main wash cycle If you are using water softener and require the right compartment for detergent for the pre-wash cycle, add the water softener on top of the detergent for the main wash cycle in the left compartment. Softener, wash-care products to preserve the shape of garments, starch Fill the compartment to no more than the MAX indicator. Add water to thick liquid concentrates in accordance with the manufacturers instructions before using them. Dissolve powder starch. If you are using liquid detergent: Add liquid detergent using measuring containers provided by the detergent manufacturer.
Switching on the appliance/selecting a programme
Set the programme and temperature using the programme selector.
The appliance is switched on by selecting a programme. The programme progress display shows the programme steps that the selected programme will carry out. The estimated programme duration (in minutes) appears in the multi-display.
Changing the spin speed/selecting rinse hold
The washing machine suggests the maximum permitted spin speed suitable for the selected programme. You can reduce this spin speed: To do this, press the Spin/RINSE HOLD button repeatedly until the required indicator is illuminated. The spin speed for the final spin can be changed even during the programme. To do this: 1. Press the START/PAUSE button. 2. Change the spin speed. 3. Press the START/PAUSE button again. RINSE HOLD With RINSE HOLD the washing is left to soak in the final rinse water. No final spin takes place, only the intermediate spin. The intermediate spin depends on the programme and cannot be changed.
Selecting additional programmes
If required, press additional programme button(s). The corresponding indicator will illuminate. If Err flashes in the multi-display, the selected additional programme cannot be used together with the wash programme set.
Two additional rinse cycles are carried out for the programmes ENERGY SAVING, COTTONS/LINEN, DELICATES, EASY-CARES and EASY IRON (for example in cases of over-sensitive skin).

Interrupting a programme A programme can at any time be interrupted by pressing the START/ PAUSE button and resumed by pressing START/PAUSE again. To cancel a programme before it has ended, turn the programme selector to OFF. Important: Be careful of water in the appliance. Adding washing Washing can be added, as long as the DOOR indicator is illuminated green. 1. Press the START/PAUSE button. The door can be opened. 2. Close the door and press the START/PAUSE button again. The programme will continue.
End of the wash cycle/removing the washing
At the end of the programme, END lights up on the programme progress display. The door can be opened as soon as the DOOR indicator is lit green. 1. Open the loading door and remove the washing. 2. Turn the programme knob to OFF. 3. Close the water valve. 4. After washing, pull out the detergent drawer a little to enable it to dry out. Keep the loading door very slightly open so that the washing machine can air. If RINSE HOLD has been selected: After the rinse hold, END lights up on the programme progress display. The water must first be drained: Either turn the programme knob to OFF, then to DRAIN and press the START/PAUSE button (the water is drained without spinning), or turn the programme knob to OFF and then to SPIN. Change the spin speed if necessary and press the START/PAUSE button (the water is drained and the washing spun).

Overdosing

If the OVERDOSING indicator is illuminated, too much detergent was used in the previous programme. The next time you wash, observe the detergent manufacturers instructions concerning amount of detergent required, and the amount of items you wash in one load.

Child safety device

If the child safety device has been activated, the door can no longer be shut. Activating the child safety device: Use a coin to turn the knob (on the inside of the door) in a clockwise direction as far as it will go.
Warning! The knob must not be depressed after being set, otherwise the child safety device is not activated. The knob must stand proud as shown in the illustration.

Deactivating the child safety device: Turn the knob in an anti-clockwise direction as far as it will go.

Cleaning and maintenance

Important! Do not use furniture care products or aggressive cleaners to clean the appliance. Wipe control panel and body with a damp cloth.

Cleaning procedure

If you plan to wash mainly at low temperature, you should run a hot programme from time to time. This will reduce any deposits and clean the appliance from the inside.
Detergent dispenser drawer
The detergent dispenser drawer should be cleaned regularly. 1. Remove the detergent dispenser drawer by pulling it firmly. 2. Remove the conditioner insert from the middle compartment. 3. Clean all parts with water. 4. Put the conditioner insert in as far as it will go, so that it is firmly in place.
5. Clean all parts of the washing machine, especially the nozzles in the top of the washing-in chamber, with a brush. 6. Insert the detergent dispenser drawer in the guide rails and push it in.

Washing drum

Rust deposits in the drum may occur due to rusting foreign bodies in the washing or tap water containing iron. Important! Do not clean the drum with acidic descaling agents, scouring agents containing chlorine or iron or steel wool. 1. Remove any rust deposits on the drum with a cleaning agent for stainless steel. 2. Run a washing cycle without any washing to clean off any cleaning agent residues. Programme: COTTONS/LINEN 60, press the TIME SAVER button, add approx. 1/4 measuring cup of detergent. 18

Door and rubber collar

Regularly check whether deposits or foreign bodies are present in the folds of the rubber collar or on the inside of the glass door. Clean the glass in the door and the rubber collar regularly.

What to do if.

Remedying small faults yourself
If during use of the appliance one of the following error codes is shown in the multi-display: E10 (Problems with the water inflow), E20 (Problems with the water outflow), E40 (door open), please consult the following table. After the error has been remedied, press the START/PAUSE button. In the event of other errors (E and a number or letter): Switch the appliance off and then on again. Set the programme again. Press the START/PAUSE button. If the error appears again, please contact your local Service Force Centre, stating the error code.
Problem Possible cause Mains plug not plugged in or fuse not working. Loading door not closed Washing machine is not properly. working. The START/PAUSE button has not been pressed for long enough. The door cannot be closed. The child safety device has been activated. Remedy Connect the plug to a mains socket. Check fuse. Close loading door - there should be an audible click. Press the START/PAUSE for a longer period of time. Deactivate the child safety device. Select another function.
When a button is The selected function pressed, Err appears in cannot be combined with the multi-display. the programme set. E40 appears. The END indicator flashes 4x, and an acoustic signal sounds 4x.

The door is not closed properly.
Close the door properly. Restart the programme.
Problem E10 appears. The END indicator flashes 1x, and an acoustic signal sounds 1x. (Problems with water inflow.)
Possible cause Tap turned off.

Remedy Turn on the tap.

Turn off the tap. Unscrew the The filter in the threaded hose, take out the filter and inlet hose fitting is blocked. clean it. Water tap is furred with lime scale or is faulty. The transit packaging has not been removed. Check the tap and have it repaired, if necessary. Removing the transit packaging.
The washing machine vibrates when operating Adjust the feet as described The screw feet not correctly or is not stable. in the installation and adjusted. connection instructions. Washing has not been spun. Only a few large items of washing in the drum. Screw connection on the inlet hose is leaking. Drain hose is leaking. Water is running out from under the washing machine. Drain pump cover is not closed properly. Washing was caught in the door. Emergency drain hose is leaking. Wash water is foaming excessively. At the end of the washing cycle, the spin stops. The OVERDOSING indicator lights up. Always load the drum as full as possible. Mix large and small items. Screw the inlet hose on tightly. Replace drain hose. Close the cover properly. Load washing carefully for the next wash. Close off emergency drain hose properly.
Too much detergent has probably been used.
Follow the manufacturer's instructions exactly when measuring out detergent.
Kink in drain hose. E20 appears. The END indicator flashes 2x, and an acoustic signal sounds 2x. (Problems with water inflow.) Do not exceed the maximum pump height of 1m.
Straighten the hose. Please contact customer service. Switch off the appliance. Disconnect the power plug. Clean the drain pump. Remove foreign bodies from the pump housing.

Drain pump is blocked.

For sink spigot connections: Clean the sink spigot. The sink spigot is blocked.
Problem Fabric softener was not rinsed in, the compartment w for conditioners is full of water.

Possible cause

Remedy
Fabric softener insert in the Clean the detergent drawer, compartment for insert the fabric softener conditioners is not correctly insert firmly. attached or is blocked. Wait until the DOOR indicator is illuminated green. The programme will continue when the power cut is over. There has been a power cut. (All the indicator are off). The door remains blocked for approx. 4 to 10 minutes. To remove washing: If water can be seen in the appliance, first drain off the water before opening the loading door (see section Carrying out an emergency drain). Observe maximum loads.

Door locked.

The door cannot be opened when the washing machine is switched on.
Washing is heavily creased.
Possibly too much washing was loaded.
If the wash result is not satisfactory

Warning! Before opening the cover of the drain pump, switch off the washing machine and remove the power plug from the power point. 1. First carry out an emergency drain. 2. Place a cloth on the floor in front of the cover of the drain pump. Residual water runs out. 3. Unscrew the pump cover in an anticlockwise direction and remove it.
4. Remove foreign bodies and fluff from the pump housing and from the pump wheel.
5. Check whether the pump wheel right at the back of the pump housing can turn. (If the wheel rotates with a jerky motion, this is normal.) If the pumping wheel cannot be turned, please contact your local Service Force Centre. 6. Insert the pump cover. Insert the guides at the sides of the cover into the guide slots and tighten the cover by turning in a clockwise direction. 7. Close off the emergency drain hose and place it in the retainer. 8. Close the plinth flap. 23

Disposal 2

Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at your local waste disposal facilities. Old appliance The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Warning: When your appliance has finished its working life, remove the plug from the mains socket. Cut off the cable and plug and dispose of them. Destroy the door lock. This prevents children from trapping themselves inside and endangering their lives.

Technical data 5

This appliance conforms with the following EU Directives: 73/23/EEC dated 19.02.1973 Low Voltage Directive 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive 92/31/EEC 93/68/EEC dated 22.07.1993 CE Marking Directive

Height x Width x Depth Depth when door is open Height adjustment Load (depending on programme) Area of use Drum spin speed Water pressure 850 x 598 x 603 mm 980 mm approx. +10/-5mm Max. 6kg Domestic see Rating Plate 1-10bar (=10100N/cm2=0.11.0MPa)

Consumption values

The consumption values were obtained under standardised conditions. They can differ in household use.
Programme selector (Temperature) COTTONS/LINEN 95 ENERGY SAVING

Load size in kg1) 3 2

Water in litres 58 54
Energy in kWh 2,20 1,02 0,70 0,52 0,42 0,35
COTTONS/LINEN 40 EASY-CARES 40 DELICATES 30 WOOL/SILK H (Hand-washing) 30
1) The load size is determined in accordance with the EN 60456 standard loads. 2) Note: Programme settings for tests in accordance with or in support of EN and IEC 60 456. Consumption values will vary from those quoted depending on the pressure and hardness of the water and its initial temperature, the room temperature, type and quantity of washing, detergent used, fluctuations in mains voltage and options selected.
Installation and connection instructions 1 Safety information concerning installation
This washing machine cannot be built-in. Before using for the first time, check the appliance for damage sustained while it was being transported. Do not under any circumstances connect an appliance that is damaged to the mains. In the event of damage to the appliance contact your supplier. Be sure to remove all the components of the transit packaging before using the appliance for the first time. Otherwise when spinning damage may be caused to the appliance or to neighbouring units or furniture. Before using the appliance for the first time, splash protection must be completed. (See Removing transit packaging). Always plug the mains plug into a correctly installed shockproof socket. If hard-wired: hard-wiring to the mains may only be carried out by an a qualified electrician. Prior to using the appliance for the first time, ensure that the rated voltage and current on the rating plate match the mains voltage and current where the appliance is to be installed. The required fuse protection is also to be found on the rating plate. If work on the plumbing is required for the proper connection of the washing machine to the water supply, this must be undertaken by a registered plumber. If work on the electricity supply system is required for the proper connection of the washing machine to the electricity supply, this must be undertaken by a registered electrician. The washing machines mains cable must only be replaced by a Service Force Engineer

Installing the appliance

Transporting the appliance
Warning: The washing machine is very heavy. There is a risk of injury. Exercise care when lifting the appliance. Do not lay the washing machine on its front nor on its right side (as seen from the front). Electrical components may get wet. Never transport the appliance without using the transit packaging. Only remove the transit packaging when the appliance is in its place of installation. Transporting the appliance without the use of the transit packaging can cause damage to the appliance. Never lift the appliance by the door when it is open nor by the plinth. When using a sack trolley to transport the washing machine: Only use the sack trolley on the side of the appliance.
Removing the transit packaging
Important! Be sure to remove all the components of the transit packaging prior to using the appliance for the first time. Keep the transit packaging in a safe place, in case it is needed at a later date when the appliance is to be moved (e.g. moving house). 1. Open the two hose retainers located at the rear of the appliance and remove the hoses and electrical cable.
2. Remove the two hose retainers from the appliance with a strong tug.
3. Remove both plastic caps sideways.
Special spanner A and sealing caps B (2 units) and C (1 unit) come with the appliance. 4. Use special spanner A to remove screw D and the compression spring. 5. Turn sealing cap C upside down as shown in the illustration. 6. Use sealing cap C to cap the hole.
7. Use special spanner A to remove the two screws E. 8. Use special spanner A to remove the four screws F. 9. Remove transit bar G. 10. Screw in the four screws F again. 11. Use sealing caps B to cap the two large holes. Important: Press all sealing caps B (2 items) and C (1 item) in firmly so that they snap into the rear wall.

Where to install

Important! The washing machine must not be operated in a room where there is a danger of frost. There is a risk of frost damage or adverse effect on the perfomance of the machine. Frost damage is not covered under the warranty. The surface on which the appliance is to be installed must be firm and level. Do not install the appliance on carpeted floors or soft floor coverings. The surface on which the appliance is to be installed must be clean and dry and free from grease, so that the appliance does not slide. 28

If the location in which the appliance is to be installed is fitted with small-format tiles, put a rubber mat (available in the shops) under the appliance. If the appliance is to stand on a base: In order for the appliance to be secure on the base, fixing plates*) must be mounted, into which the appliance is inserted.
If the appliance is to stand on a floor which moves, e.g. a suspended wooden floor: Place the appliance in an area as close as possible to a corner of the room. Screw a water-resistant wooden board (at least 15 mm thick) onto at least 2 of the floor joists.
Making the appliance level
The four feet of the appliance are pre-adjusted. Large degrees of unevenness can be compensated for by individually adjusting the height adjustable screw feet. Use the special spanner supplied to do this. Important! Do not use pieces of wood, cardboard or such like to level out unevenness in the floor, but adjust the height adjustable screw feet instead.

Electrical Connection 1

Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. The appliance is supplied with a 13 amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used. Should the plug need to be replaced for any reason, proceed as described below. The wires in the mains lead are coloured in accordance with the following code: Green and Yellow: Earth Blue: Neutral Brown: Live The wire coloured green and yellow must be connected to the terminal marked with the letter E or by the earth symbol E or coloured green and yellow. The wire coloured blue must be connected to the terminal N or coloured black. The wire coloured brown must be connected to the terminal marked L or coloured red. Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath. WARNING! A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that the cut off plug is disposed of safely.

Permanent Connection

In the case of a permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply (mains), with a minimum gap of 3mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations. The switch must not break the yellow and green earth cable at any point. This appliance complies with the requirements laid out in the EEC Directive 76/899. Voltage 240 V AC: Fuse rating 13amps See rating plate for further information. This appliance meets VDE requirements. Particular regulations of local electricity authorities must be observed. This appliance conforms to EEC Directive No. 82/499/EWG on radio interference. WARNING! Repairs to electrical appliances must only be carried out by trained personnel. Improper repairs may lead to serious risks for the user.

Connecting the appliance to the water supply
Important: This appliance must not be connected to the hot water supply. When connecting the appliance, use only new hose kits. Only connect the appliance to the drinking water supply. Rain water or water for industrial use may only be used if it fulfils the requirements of DIN1986 and DIN1988. Do not kink or crush the water inlet hose or drain hose.

Permitted water pressure

The water pressure must be at least 1 bar (=10N/cm2 =0.1MPa), and may be a maximum of 10bar (=100N/cm2 =1MPa). If more than 10bar: Connect a pressure reduction valve. If less than 1bar: Disconnect the appliance end of the inlet hose from the solenoid inlet valve and remove the flow meter. (In addition remove the filter using pointed pliers and take out the rubber gasket behind it.) Replace the filter. 31

Water inlet

A 1.35m long pressure hose is supplied with the appliance. If a longer inlet hose is required, only hoses from the manufacturer are to be used. Your local Service Force stocks hose kits of different lengths. Sealing rings are either inserted in the plastic nuts of the threaded hose fitting or are included as spare parts. Do not use any other sealing rings. Important! All threaded hose fittings must only be tightened by hand. 1. Connect the hose with the right-angle connector to the machine. Important! Do not position the inlet hose vertically downwards. Position it to the right or the left as shown in the illustration.
2. Connect the hose with the straight connector to a water tap with an R (inch) screw thread. 3. Slowly turn on the tap and check that all connections are watertight.

Water Drainage

The appliance drain hose should hook into a standpipe, the hook in the drain hose is formed using the plastic U-Piece supplied. The standpipe should have an internal diameter of approximately 38 mm (see diagram) thus ensuring there is an air break between the drain hose and standpipe. Important! It is essential to lay the drainage hose without kinks. When discharging into a standpipe ensure that the top of the curve in the hose end is no more than 90 cm (35.4) and no less than 60 cm (23.6) above floor level.
The upright standpipe should have a minimum, length of 30 cm (12) from the bottom of the elbow to the top of the pipe (see diagram). Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water. Longer drain hoses are available in lengths of 2.7 and 4 metres from your Service Force Centre. For drainage into an outlet spigot: If the outlet spigot has not been used before, remove any blanking plug that may be in place. Push the drain hose onto the spigot and secure with a clip if required. Ensure the drain hose is looped upwards to prevent waste water from the sink entering the washing machine. Important! The end of the drainage hose must not be submerged in the pumped-out water. Otherwise, the water could be sucked back into the appliance. 33

Pumping heights of over 1 metre
The washing machines drain pump is able to pump water to a height of 1metre, calculated from the surface on which the appliance is installed. Important! If pumping height is over 1 metre malfunctions and damage to the appliance may arise. For pumping heights over 1metre a conversion kit can be obtained. Please contact Service Force Centre.

Warranty conditions

Great Britain
Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate. The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's operating and maintenance instructions. The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. All service work under this guarantee must be undertaken by a Service Force Centre. Any appliance or defective part replaced shall become the Company's property. This guarantee is in addition to your statutory and other legal rights. Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours in which case a premium will be charged. Exclusions This guarantee does not cover: Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable parts of glass or plastic. Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom. Appliances found to be in use within a commercial environment, plus those which are subject to rental agreements. Products of AEG manufacture which are not marketed by AEG. European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications: The guarantee starts from the date you first purchased your product. The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products. This guarantee relates to you and cannot be transferred to another user. Your new home is within the European Community (EC) or European Free Trade Area. The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal household. The product is installed taking into account regulations in your new country. Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Germany Italy Sweden UK Senlis Nrnberg Pordenone Stockholm Luton +33 (0) 29 +49 (0) 7378 +39 (0) +46 (0) 5360 +44 (0) 350

Bulgaria Electrolux Bulgaria E.O.O.D. 91 Levski Blvd. 1000 Sofia Tel.: Fax. 5276 Cyprus Hadjikyrlakos & Sons Ltd. Prodromou 121 P.O. Box 21587 Nicosia 1511 Service Telephones: Nicosia Limassol Larnaca Paphos 699 Estonia Electrolux Estonia Ltd. Mustame tee 24 EE0006 Tallinn Tel.: (372) 090 Fax: (372) 092
Kuwait/Arabian Gulf Ali Al-Ghanim Est. P.O. Box 21540 - Safat Tel.: 4822190 Fax: 4820116 Lebanon Adib & Assaferi P.O. Box 539 Tripoli
Latvia Electrolux Latvija Ltd. Kr.Barona iela 130/2 Riga, LV-1012 Tel.: Fax: 371 7845954
Hong Kong Dah Chong Hong Ltd. 20 Kai Cheung Road Kowloon Bay Kowloon - Hong Kong Tel.: 0085222621620 Fax: 0085227550333 Israel Evis Ltd. Tadiran-Ampa Service 10 Gibonay Israel Street New Industrial Zone Netanya, 42504 Israel
Lithuania Electrolux Lithuania Verkui Vilnus Tel.: 3326 Fax: 3366 Malaysia Arzbergh Engineering No. 49A/B, Jalan Petaling Utama Petaling Jaya Tel.: 1084 Fax: 1082
Russia Electrolux Russia Ltd. 16 Olympiysky prospekt 129090 Moscow Tel.: (095) Fax: (095) Saudi Arabia Awad Badi Nahas Est Shara Siteen Jeddah 21463 Phone: 6646583 Alia Trading Co Mecca Road Riyadh 11491 Phone 4645977 Slovenia Electrolux Slovenia D.O.O. Traska Ul. Ljubljana Tel.: 137 Fax: 238
Japan Electrolux Japan Ltd. Domestic Appliances Department Maruzen Showa Warehouse Building Tookai 4-5-12, Ota-ku 143-006 Tokyo Tel.: 0120-13-7117 Fax: 03-3790-5257 Thailand Olympia Thai Tower, 444 Rachadapiser Road Samsennok- Huaykwang 10320 Bangkok Thailand Tel.: 006625136111 Fax: 006625136334 Hungary Electrolux Lehel KFT Erzsbet Kirlyn tja 87. 1142 Budapest Tel.: 00361/467-3200
Singapore Group Pte Ltd. 833 Bukit Timah Road Unit no. 01-11 Royalville 279887 Singapore Tel.: Fax: 0065 64638488
Slovakia Rep. Electrolux Slovakia S.R.O. Seberiniho 03 Bratislava Tel.: 4322, 4355 Fax: 6976
South Africa AEG (Pty) Ltd. 55, 12th Road P.O. Box 64 Kew/Johannesburg 2000 Tel.: 8069111

Czech Rep.

ELECTROLUX DOMC SPOTEBIE CZ DIVIZE ELECTROLUX S.R.O. Customer Centre Hanusova ul. Praha 4 Tel.: 6112 Telefax: 3504

Service and Spare Parts

If the event of your appliance requiring service, or if you wish to purchase spare parts, please contact Service Force by telephoning: Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce.co.uk Before calling out an engineer, please ensure you have read the details under the heading What to do if. When you contact the Service Force Centre you will need to give the following details: 1. Your name, address and post code. 2. Your telephone number. 3. Clear and concise details of the fault. 4. The model and serial number of the appliance (found on the rating plate) 5. The purchase date. Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee service calls. Customer Care For general enquiries concerning your AEG appliance, or for further information on AEG products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.aeg.co.uk. Customer Care Department For Customer Service in the Republic of Ireland please contact us at the adMajor Appliances dress below: AEG Domestic Appliances AEG/ Electrolux Group (Ire) Ltd Addington Way Long Mile Road/ Dublin 12 Luton Republic of Ireland Bedfordshire, LU4 9QQ Tel: +353 (0) Tel: (*) Email: service.eid@electrolux.ie (*) Calls may be recorded for training purposes 39