Printable Version: AEG-ELECTROLUX::: MCD2661EM

Pagina 1 di 1

MICROWAVE OVEN - MICROWAVE OVEN BUILT IN

MCD2661EM

FEATURES LED display 24 hr / 12 hr clock 5 microwave power level End signal User friendly interface Cavity light: 25W bulb 2 Autocook by weight programs 4 Defrost by weight programs 6 auto weight combi microwave and grill programmes Non-integrated glass turntable Turntable diameter: 32,5 cm
SPECIFICATIONS Color Maximum microwave output (W) Cavity size net (liters) Dimensions (HxWxD) Power cord length (m) Conected load (W) Voltage (V)/Frequency (Hz) Net weight Registered office: Corso Lino Zanussi, Porcia PN Italy stainless Steel 900 25,37 460x592x437 1,220-60 18,5 Kg
e-mail:elint.diam@electrolux.it
Design and Specifications subject to change without notice. Specification sheet colors may vary depending on equipment. Electrolux International spa
https://www.eluxintl.it/prod/its/itsanpro.nsf/PrintableIndexWeb/0947608520?OpenDo. 29/01/2009

LAVAMAT 52810

Washing machine User information

Dear customer,

Please read this User Information carefully and keep it to refer to at a later date. Pass this User Information on to any subsequent owner of the appliance.
The following symbols are used in the text: Safety instructions Warning: Notes that concern your personal safety. Attention: Notes that show how to avoid damage to the appliance. Useful tips and hints Environmental information

Contents

Operating Instructions.
Safety. Description of the appliance. Control Panel. Programme overview. 8
Before the first wash. 10 Preparing and sorting washing. 11 Running a washing cycle. Opening the door/loading washing. Adding detergent/additives. Switching on the appliance/selecting a programme. Changing spin speed/selecting rinse hold. Selecting the programme options. PRE-WASH. TIME SAVER. Switching RINSE + on and off. Setting the delay timer. Starting a programme. Interrupting a programme/adding washing. Washing cycle complete/removing the washing. 18
Child safety device. 19 Cleaning and maintenance. 20 What to do if. Remedying small malfunctions. If the wash results are not satisfactory. Carrying out an emergency drain. Drain pump. 26
Disposal. 27 Technical data. 28 Consumption values. 29
Installation and connection instructions.
Installing the appliance. Transporting the appliance. Unpacking. Where to install. Making the appliance level.
Safety information for the installation. 30
Electrical connection. 36 Connecting to the water supply. 37 Water inlet. 38 Water drainage. 39
Guarantee/Customer Service. Service
Operating Instructions 1 Safety
Prior to using for the first time
Follow the Instructions for installation and connection. If the appliance is delivered in the winter months when there are minus temperatures: Store the washing machine at room temperature for 24 hours before using for the first time.

Correct use

The washing machine is only designed for the washing of normal domestic laundry at home. Additions or modifications to the washing machine are not permitted. Use only detergents and additives that are suitable for use in domestic washing machines. The washing must not contain any inflammable solutions. Danger of explosion! Do not use the washing machine for dry cleaning. Dyes/colour removers may only be used in the washing machine, if the manufacturer of these products expressly permits this. We cannot be held responsible for any damage arising.
Child safety and Infirm Persons
Keep packaging away from children. There is a risk of suffocation. This appliance is not intended for use by people (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children often do not recognise the hazards associated with electrical appliances. Do not allow children to use the washing machine unsupervised. Make sure that children and pets dont climb into the drum of the washing machine. Could endanger life!

General safety

Repairs to the washing machine must only be carried out by qualified service engineers. Never use the washing machine if the mains cable is damaged; or if the control panel, work top or plinth area is damaged such that the inside of the appliance is freely accessible. Switch off the washing machine before cleaning, maintenance and servicing. In addition, pull the mains plug out of the socket or in the case of a permanent connection switch off the cut-out in the fuse box or remove the screw fuse completely. If operation is stopped, disconnect the appliance from the mains supply and shut off the water tap. Never unplug the appliance by pulling on the cable. Always pull the plug. Multi-way plugs, connectors and extension cables must not be used. This could constitute a fire hazard through overheating. Never wash the washing machine down with a water jet. Danger of electric shock! In washing programmes with high temperatures the glass in the door gets hot. Do not touch it. Before emergency emptying of the appliance, before cleaning the drain pump or opening the door in an emergency, let the water cool down. Small animals can nibble at the cables and water hoses. Danger of electric shock and danger of water damage! Keep small animals away from the washing machine.

Description of the appliance
Detergent dispenser drawer Control panel
Rating plate (behind door)
Screw feet (height adjustable)

Plinth flap/ Drain pump

Control Panel
SPIN/RINSE HOLD button Programme option buttons Programme Progress display

DELAY TIMER button

DOOR indicator

Programme knob

START/PAUSE button

Programme overview

Additional programmes max. load 1) (dry washing) PRE WASH Programme TIME SAVER Spin speed RINSE HOLD

1000

ENERGY SAVING2) COTTONS/LINEN 95, 60, 40, 30 EASY-CARES 60, 40 EASY IRON 40

6kg 6kg 3kg 1kg

3)
DELICATES 40, 30 WOOL/SILK H (Hand-washing) 30, COLD RINSE DRAIN SPIN
1) A 10 litre bucket contains approx. 2.5 kg of dry washing (cotton) 2) Programme settings for tests in accordance with or in support of EN and IEC are described in the section Consumption values. 3) Recommended load for short progammes is 3kg; full loading is possible however with somewhat reduced cleaning results.

600

Application/Features

Care symbols1)

Energy-saving programme at 60C for lightly to normally soiled whites/coloureds made of cotton/linen. Programme for normally to heavily soiled coloureds/whites made of cotton/ linen. Programme for easy-care mixed fibres and synthetics. Special programme at 40C for easy-care fabrics which after being washed using this programme need to be ironed only lightly or not at all. Gentle programme for delicate fabrics such as bonded fibres, micro-fibres, synthetics, net curtains (load max. 20 to 25 m2 net curtains). With RINSE HOLD also suitable for materials that have climatic membranes, e.g. outdoor clothing. Specially gentle programme for machine and hand-washable wool/silk. Separate gentle rinse (3 rinse cycles, liquid conditioner is washed in from the compartment w, spin). Not suitable for wool. When loading easy-care or delicate items, reduce the spin speed. Draining following a rinse hold. Draining and spinning, e.g. following a rinse hold, or separate spinning of hand-washed cottons/linen. Reduce the spin revolution speed if spinning easy-care, delicate or woollen items.

1) The figures in the care symbols indicate the maximum temperatures.

MO JMO IKN KN IK

QLH JMO

Before the first wash

1. Open the detergent drawer. 2. Pour approx. 2 litres of water through the detergent drawer into the washing machine. This closes the water container when the next programme is started and the economy valve can function properly 3. To remove any production-related residues from the drum and water tank, perform the first wash cycle without a load. Programme: COTTONS/LINEN 95, press the TIME SAVER button, add approx. 1/4 measuring cup of detergent.
Preparing and sorting washing
Preparing washing Empty pockets. Remove foreign bodies (e. g. coins, paper clips, nails, etc.). Do up zips, button up covers to prevent damage to washing. Remove the runners from net curtains or cover them with a net or a bag. Wash sensitive and small items in a net or a pillow case, e.g. net curtains, tights, socks, handkerchiefs, bras. Important! Bras and other items containing wires should NOT be washed in this washing machine. Sorting washing By colour: Wash white and coloured washing separately. Washing can run. By temperature, type of washing and care symbol. Important! Do not wash fabrics with care symbol G (= do not wash!) in the washing machine.

Running a washing cycle

Opening the door/loading washing
1. To open the door: pull the door by the handle. When the machine is switched on, the DOOR light and the START/ PAUSE light indicate whether the door can be opened:
DOOR indicator flashes lit is off START/PAUSE indicator flashes lit flashes Can the door be opened? yes, after about 2 minutes no, water level and/or temperature too high yes
2. Unfold washing and load it loosely into the machine. Mix large and small items. Important! Do not get any washing caught between the door and the rubber seal. 3. Push the door shut firmly. Door catch must audibly click shut.
Adding detergent/additives
Warning! Use only detergents and additives that are suitable for use in domestic washing machines.
For USA and Canada only! Important! Only LOW-SUDSING detergent suitable for a front-loading washing machine can be used in this machine. This machine can heat the water up to 95 degrees celsius, or 200 degrees fahrenheit, and care should be taken to ensure that the correct washing powder is used. If you have any doubt, check with your dealer or the distributor. WARRANTY AND CONSEQUENTIAL DAMAGES ARE VOIDED IF A LOW SUDSING DETERGENT IS NOT USED. Dose detergent and additives according to the instructions of the detergent and additive manufacturers. Follow the advice on the packaging. Dosing depends upon: the washings degree of soiling, the size of the load the degree of hardness of the water supply. If the manufacturer does not give instructions for small loads: for a half load, use a third less, for a very small load, use only half of the detergent that is recommended for a full load. From water hardness 2 (= medium) upwards, water softener should be used. Detergent can then always be dosed for water hardness 1 (= soft). Your local water company will be able to give you information about the water hardness in your area.

1. Pull the detergent dispenser drawer out as far as the stop. 2. Add the detergent/additives. 3. Push the drawer in fully.
Washing powder/tablets for the main wash Softeners/ wash-care products to preserve the shape of garments/ starch Washing powder/tablets for the pre-wash or inwash stain treatment
Washing powder/tablets for the main wash If you are using water softener and need the right-hand compartment for the pre-wash/stain treatment agent, add the water softener to the main wash detergent in the left compartment. Softeners, wash-care products to preserve the shape of garments, starch Do not fill the compartment beyond the MAX mark. Dilute thick liquid concentrates according to the manufacturers instructions before putting them into the drawer. Dissolve powder starches. If you use liquid detergents: Add liquid detergent using the dosage containers provided by the detergent manufacturer.
Switching on the appliance/selecting a programme
Set the programme and temperature using the programme knob. By selecting a programme, you switch the appliance on at the same time. The programme progress display indicates the programme steps that the selected programme will perform.
Changing spin speed/selecting rinse hold
The washing machine suggests the maximum permitted speed that is suitable for the selected programme. You can reduce this speed: Press the SPIN/RINSE HOLD button repeatedly until the desired display lights up. The speed for the final spin can still be altered during the programme. To do this: 1. Press the START/PAUSE button. 2. Change speed. 3. Press the START/PAUSE button again. RINSE HOLD If RINSE HOLD is selected, the washing is left to soak in the last rinse water. There is no final spin after the intermediate spin(s). Intermediate spins are programme-dependent and cannot be altered.
Selecting the programme options
If desired, press the programme option button(s). The corresponding light lights up.

PRE-WASH

Warm pre-wash before the main wash, which follows automatically; intermediate spin in the COTTONS/LINEN and EASY-CARES/EASY IRON programmes; no intermediate spin in the DELICATES programme.

TIME SAVER

Short wash cycle for lightly soiled washing.
Switching RINSE + on and off
When RINSE + is switched on, there are two additional rinses in the COTTONS/LINEN, EASY-CARES/EASY IRON, DELICATES and GENTLE RINSE programmes. RINSE + remains permanently saved even after the appliance is switched off. To switch on RINSE +: 1. Turn the programme knob to COTTONS/LINEN, EASY-CARES/EASY IRON or DELICATES (at any temperature). 2. Hold down the buttons PRE-WASH and DELAY TIMER at the same time, until RINSE and RINSE + light up on the programme progress display. RINSE + is now permanently switched on. RINSE + is lit on the programme progress display before the start of the programme and during the additional rinses. To switch off RINSE +: 1. Turn the programme knob to COTTONS/LINEN, EASY-CARES/EASY IRON or DELICATES (at any temperature). 2. Hold down the buttons PRE-WASH and DELAY TIMER at the same time, until RINSE + goes out on the programme progress display. RINSE + is now permanently switched off.

Setting the delay timer

The DELAY TIMER button allows the start of a programme to be delayed. 1. Select programme. 2. Press DELAY TIMER button once, if the wash programme is to start after 6 hours. The display 6h lights up. Press DELAY TIMER button twice, if the wash programme is to start after 3 hours. The display 3h lights up. If you press the DELAY TIMER button again, the time delay is cancelled. The display goes out. 3. To activate the time delay, press the START/PAUSE button. Note: If a time delay of 6 hours is selected, the display 6h is lit. After 3 hours the display changes and 3h is lit. After a total of 6 hours the wash programme then starts.

Starting a programme

1. Check that the water tap is open. 2. Press the START/PAUSE button. The programme is started or starts after the time delay set has elapsed. During the wash programme, the current programme step is displayed on the programme progress display. If the START/PAUSE button is pressed and the END indicator flashes 4 times, the door is not closed properly. Push the door firmly closed and press the START/PAUSE button again.
Interrupting a programme/adding washing
Interrupting a programme A washing programme can be interrupted at any time by pressing the START/PAUSE button. It is then re-started by pressing the START/ PAUSE button again. To stop the washing machine before the programme has ended, turn the programme knob to OFF. Important! Be careful if there is water in the appliance! Adding washing It is possible to add washing, as long as the DOOR light is not lit. 1. Press the START/PAUSE button. The door can be opened. 2. Shut door and press the START/PAUSE button again. The programme continues. 17
Washing cycle complete/removing the washing
At the end of the programme, END lights up on the programme progress display. The door can be opened as soon as the DOOR light goes off and the END light has come on. 1. Open the door and remove the washing. 2. Turn the programme knob to OFF. 3. Close the water tap. 4. After the wash, pull out the detergent dispenser drawer slightly to allow it to dry. Leave the door slightly open to air the inside of the washing machine. If RINSE HOLD was selected: After a rinse hold, DOOR and END light up on the programme progress display. The water must first be drained: Either turn the programme knob to OFF, then to DRAIN and press the START/PAUSE button (the water is drained without spinning), or turn the programme knob to OFF and then to SPIN. Depending upon the type of washing, reduce the spin speed if necessary and press the START/PAUSE button (the water is drained and the washing spun).

Child safety device

When the child safety device is set, the door can no longer be closed. Setting the child safety device: Use a coin to turn the knob (on the inside of the door) in a clockwise direction as far as it will go.
Warning! The knob must not be sunk-in after being set, otherwise the child safety device is not active. The knob must stand out as shown in the illustration. Releasing the child safety device: Turn the knob anti-clockwise as far as it will go.

Cleaning and maintenance

Important! Do not use furniture care products or aggressive cleaners to clean the appliance. Wipe control panel and body with a damp cloth.

Cleaning procedure

If you plan to wash mainly at low temperature, you should run a hot programme from time to time. This will reduce any deposits and clean the appliance from the inside.
Detergent dispenser drawer
The detergent dispenser drawer should be cleaned regularly. 1. Remove the detergent dispenser drawer by pulling it firmly. 2. Remove the conditioner insert from the middle compartment. 3. Clean all parts with water. 4. Put the conditioner insert in as far as it will go, so that it is firmly in place.
5. Clean all parts of the washing machine, especially the nozzles in the top of the washing-in chamber, with a brush. 6. Insert the detergent dispenser drawer in the guide rails and push it in.

Washing drum

Rust deposits in the drum may occur due to rusting foreign bodies in the washing or tap water containing iron. Important! Do not clean the drum with acidic descaling agents, scouring agents containing chlorine or iron or steel wool. 1. Remove any rust deposits on the drum with a cleaning agent for stainless steel. 2. Run a washing cycle without any washing to clean off any cleaning agent residues. Programme: COTTONS/LINEN 95, press the TIME SAVER button, add approx. 1/4 measuring cup of detergent.

Door and rubber collar

Regularly check whether deposits or foreign bodies are present in the folds of the rubber collar or on the inside of the glass door. Clean the glass in the door and the rubber collar regularly.

What to do if.

Remedying small malfunctions
If the programme progress display indicates one of the following fault codes during operation: END flashes 1x (problem with water intake), END flashes 2x (problem with water drainage), END flashes 4x (door open), please look at the following table. When the fault is remedied, press the START/PAUSE button. If there are other fault codes (one or more flashing lights on the programme progress display): Switch the appliance off and on again. Re-set the programme. Press the START/PAUSE button. If the fault is displayed again, please contact the Customer Care Department.
Problem Possible cause Mains plug not plugged in or fuse not working. Washing machine does not work. Door not closed properly. START/PAUSE button was not pressed for long enough. Door cannot be closed. END display flashes 4x. Remedy Plug in mains plug. Check fuse. Close door there should be an audible click. Press START/PAUSE button for longer.

Child safety device engaged. Release child safety device. Door is not closed properly. Tap turned off. Close door properly. Start programme again. Turn tap on. Turn off the water tap. Unscrew hose, take out filter and clean it. Check the water tap and have it repaired if necessary.
END display flashes 1x. (Problems with water inflow)
Filter in the screw connection of the inlet hose is blocked. Water tap is blocked with limescale or faulty.
The transport lock has not Removing the transport lock. been removed. The washing machine vibrates when operating Adjust the feet as described The screw feet not correctly or is not stable. in the installation and conadjusted. nection instructions.
Problem Washing has not been spun.
Possible cause Only a few large items of washing in the drum.
Remedy Always load the drum as full as possible. Mix large and small items.
Screw connection on the inTighten inlet hose. let hose is leaking. Drain hose is leaking. Water is leaking out un- Drain pump cover is not derneath the washing closed properly. machine. Washing was caught in the door. Emergency drain hose is leaking. Washing water is foam- Probably too much detering excessively. gent has been used. Kink in drain hose. Maximum pumping height of 1m exceeded. END display flashes 2x. (Problems with water outflow.) Replace drain hose. Close cover properly. Load washing carefully for the next wash. Close off emergency drain hose properly. Dose detergent exactly as instructed by manufacturer. Remove kink. Please contact Customer Care Department. Switch off appliance. Pull out mains plug. Clean drain pump. Remove foreign bodies from pump housing. Clean sink outlet.

Drain pump is blocked.

With connection to sink outlet: sink outlet is blocked. Fabric softener not rinsed in, w compartment for additives is filled with water. Conditioner insert in the compartment for additives is not correctly attached or is blocked. Door locked.
Clean detergent dispenser drawer, insert conditioner insert firmly. Wait until DOOR light goes off and END light comes on. Programme continues, when power cut is over. To remove washing: If water can be seen in the appliance, before opening the door, first drain off the water. (See section Carrying out an emergency drain.) Observe maximum loads.
Door cannot be opened Power cut. (All display indiwhen appliance is cators are off.) switched on. Door remains locked for approx. 2 minutes.
Washing is heavily creased.
Possibly too much washing was loaded.
If the wash results are not satisfactory
Washing is grey and scale is being deposited in the drum Too little detergent is being used. The right detergent was not used. Special soiling was not pre-treated. Programme or temperature was not correctly set. There are grey stains on the washing. Washing soiled with ointment, grease or oil was washed with too little detergent. It was washed at too low a temperature. A common cause is that fabric conditioner especially a concentrate has got onto the washing. Such stains should be washed out as quickly as possible and make sure that you are careful when using fabric conditioner. After the last rinse foam can still be seen. Modern detergents may create foam even in the last rinse cycle. The washing is however sufficiently rinsed. There are white residues on the washing. This is due to the insoluble ingredients in modern detergents. They are not caused by insufficient rinsing. Shake or brush the washing. If possible turn the washing inside out before washing. Check your choice of detergent. Especially with dark colours it is advisable to use liquid detergents.

Technical data 5

This appliance conforms with the following EU Directives: 73/23/EEC dated 19.02.1973 Low Voltage Directive 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive 92/31/EEC 93/68/EEC dated 22.07.1993 CE Marking Directive
Height x Width x Depth Depth when door is open Height adjustment Load (depending on programme) Area of use Drum spin speed Water pressure 850 x 598 x 603 mm 980 mm approx. +10/-5mm Max. 6kg Domestic see programme overview 0.5-10bar (=5100N/cm2=0.051.0MPa)

Consumption values

The consumption values were obtained under standardised conditions. They may vary when operating in domestic conditions.
Programme knob (Temperature) COTTONS/LINEN 95 ENERGY SAVING

Load in kg1) 3 2

Water in litres 58 54
Energy in kWh 2,20 1,14 0,70 0,52 0,42 0,45

Time in minutes 66 54

COTTONS/LINEN 40 EASY-CARES 40 DELICATES 30 WOOL/SILK H (Handwashing) 30
1) The load is determined in accordance with EN 60456 Standard Loads. 2) Note: Programme setting for tests in accordance with or supporting EN and IEC 60 456. Actual consumption will vary from the indicated values depending on water pressure, water hardness, water temperature at filling, room temperature, type and quantity of washing, detergent used, variations in mains voltage and any additional programme functions selected.
Installation and connection instructions 1 Safety information for the installation
This washing machine cannot be built-in. Before using for the first time, check the appliance for damage sustained while it was being transported. Do not under any circumstances connect an appliance that is damaged. In the case of damage, please contact your supplier. Before using for the first time, all parts of the transport lock must be removed. Otherwise when spinning damage may be caused to the appliance or to neighbouring units or furniture. Before using the appliance for the first time, splash protection must be completed. (See Removing the transit packaging.) Always plug the mains plug into a correctly installed shockproof socket. Prior to using the appliance for the first time, ensure that the rated voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating is also to be found on the rating plate. If work on the plumbing is required for the proper connection of the washing machine to the water supply, this must be undertaken by a competent person. If work on the electricity supply system is required for the proper connection of the washing machine to the electricity supply, this must be undertaken by a registered electrician. Should the appliance power supply cable need to be replaced, this must be carried out by our Service Force Centre. The power supply cable must be easily accessible after installing the appliance. Connect the machine to an earthed socket.

Installing the appliance

Transporting the appliance
Warning! The washing machine is very heavy. Risk of injury. Be careful when lifting. Do not lay the appliance on its front nor on its right side (as seen from the front). Electrical components may get wet. Never transport the appliance without its transport lock. Only remove the transport lock when the appliance is in its place of installation. Transporting the appliance without its transport lock can lead to damage to the appliance. Never lift the appliance by the door when it is open nor by the plinth. When moving using a sack trolley: Only use the sack trolley on the side of the appliance.

Unpacking

The transport safeguard must be removed before putting the appliance into operation. Important! You are advised to keep all the packaging for re-use in case the machine is to be transported again. 1. After removing all the packaging, with assistance carefully lay machine on its back to remove the polystyrene base from the bottom.
2. Remove the power supply cable and the draining hose from the hose holders on the rear of the appliance.
3. With a suitable spanner unscrew and remove the central rear bolt A. Slide out the relevant plastic spacer.
4. Unscrew and remove the two large rear bolts B and the six smaller bolts C.

5. Remove the bracket D.

6. Refit the six smaller bolts C.
7. Open the porthole and remove the polystyrene block fitted with the adhesive tape on the door seal.
8. Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet. Important! All the different plug caps are supplied with the appliance in the plastic bag containing the instruction booklet. Connect the water inlet hose as described under the paragraph Water inlet.

Where to install

Important! The appliance must not be used in a room where there is a danger of frost. Frost damage or impaired operation! Frost damage is not covered by the warranty. The surface on which the appliance is to be installed must be firm and level. Do not install the appliance on carpets or on soft floor coverings. The surface on which the appliance is to be installed must be clean and dry and free from coverings that move, so that the appliance does not slide. If the location in which the appliance is to be installed is fitted with small-format tiles, put a rubber mat (available in the shops) under the appliance.

Making the appliance level
The four feet of the appliance are pre-adjusted. Large degrees of unevenness can be compensated for by individually adjusting the height adjustable screw feet. Use the special spanner supplied to do this. Important! Do not use pieces of wood, cardboard or such like to level out unevenness in the floor, but adjust the height adjustable screw feet instead.

Electrical connection

Details about the voltage, type of supply and the fuses required are to be found on the rating plate. The rating plate is next to the doorway.
Connecting to the water supply

Permitted water pressure

The water pressure must be at least 0.5bar (=5N/cm2 =0.05MPa) and may be a maximum of 10bar (=100N/cm2 =1MPa). If more than 10bar: Connect a pressure reduction valve. If less than 0.5bar: Disconnect the appliance end of the inlet hose from the solenoid inlet valve and remove the flow meter. (In addition remove the filter using pointed pliers and take out the rubber gasket behind it.) Re-insert the filter.

Water inlet

Attention! An inlet hose is supplied and can been found inside the machine drum. Do not use the hose from your previous machine to connect to the water supply. This appliance must not be connected to the hot water system. 1. Open the porthole and extract the inlet hose. 2. Connect the hose with the angled connection to the machine. Important! Do not place the inlet hose downwards. Angle the hose to the left or right depending on the position of your water tap. 3. Set the hose correctly by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks. 4. Connect the hose to a tap with a 3/4 thread. Always use the hose supplied with the appliance. Installation should comply with local water authority and building regulations requirements. A minimum water pressure of 0.05 MPa (0.5 bar) is required for safe operation of the appliance. If you cannot make the cold water connection direct from the rising mains, you may be able to operate the appliance from your cold water storage system. There should be a minimum distance of 5.02m (16.5 ft) between the appliances inlet and the bottom of the water storage tank.

Water drainage

The maximum permitted difference between the height of the surface on which the appliance is installed and the water outlet is 1 metre. Only original hoses may be used to extend hoses. (A maximum of 3 m laid on the floor and then 80 cm vertically). The Customer Care Department stocks outlet hoses of different lengths. Draining water into a sink outlet Secure the outlet/sink outlet joint with a hose band clip (available from your dealer).

Draining water into a wash basin/bath Important! Small basins are not suitable. Water may overflow. The end of the drain hose must not be in the water that has been pumped out. Otherwise water could be sucked back into the appliance. When draining into a wash basin or a bath, secure the drain hose with the supplied elbow to stop it slipping. Otherwise the water running out can force the hose out of the basin. When pumping the water out, check that the water is running away fast enough.

Pumping heights over 1 m

The washing machines drain pump is able to pump water to a height of 1meter, calculated from the surface on which the appliance is installed. Warning! If pumping height is over 1 metre, malfunctions and damage to the appliance may arise. For pumping heights over 1metre a conversion kit can be obtained. Please contact the Customer Care Department. 39
Guarantee/Customer Service

European Guarantee

This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law. If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qualifications: The appliance guarantee starts from the date you first purchased the appliance which will be evidenced by production of a valid purchase document issued by the seller of the appliance. The appliance guarantee is for the same period and to the same extent for labour and parts as exists in your new country of residence for this particular model or range of appliances. The appliance guarantee is personal to the original purchaser of the appliance and cannot be transferred to another user. The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within the home, i.e. is not used for commercial purposes. The appliance is installed in accordance with all relevant regulations in force within your new country of residence. The provisions of this European Guarantee do not affect any of the rights granted to you by law.

www.electrolux.com p

Albania Belgique/Belgi/ Belgien esk republika Danmark Deutschland Eesti Espaa France Great Britain Hellas Hrvatska Ireland Italia Latvija Lithuania Luxembourg Magyarorszg Nederland Norge sterreich Polska Portugal Romania Schweiz/Suisse/ Svizzera Slovenija Slovensko
+450 +44 ++00 +622 +030 +88 www.electrolux.fr +++338 +753 +39 (0) +34 +3702780607 +++300 +222 ++300 ++30 +111 +731 +43 22
Rr. Pjeter Bogdani Nr. 7 Tirane Bergensesteenweg 719, 1502 Lembeek Budjovick 3, Praha 4, Sjllandsgade 2, 7000 Fredericia Muggenhofer Str. 135, 90429 Nrnberg Mustame tee 24, 10621 Tallinn Carretera M-300, Km. 29,900 Alcal de Henares Madrid
Addington Way, Luton, Bedfordshire LU4 9QQ 4 Limnou Str., 54627 Thessaloniki Slavonska avenija 3, 10000 Zagreb Long Mile Road Dublin 12 C.so Lino Zanussi, 26 - 33080 Porcia (PN) Kr. Barona iela 130/2, LV-1012, Riga irmn 67, LT 09001 Vilnius Rue de Bitbourg, 7, L-1273 Hamm H-1142 Budapest XIV, Erzsbet kirlyn tja 87 Vennootsweg 1, 2404 CG Alphen aan den Rijn Rislkkvn. 2 , 0508 Oslo Herziggasse 9, 1230 Wien ul. Kolejowa 5/7, Warszawa Quinta da Fonte - Edificio Gonalves Zarco Q - 518 Pao de Arcos Str. Garii Progresului 2, S4, 040671 RO Industriestrasse 10, CH-5506 Mgenwil Electrolux Ljubljana d.o.o. Gerbieva 98, 1000 Ljubljana Electrolux Slovakia s.r.o., Electrolux Domce spotrebie SK, Seberniho 1, Bratislava

Suomi Sverige Trkiye

www.electrolux.fi +46 (0)++937 7837
Electrolux Service, S:t Gransgatan 143, S-Stockholm Tarlaba caddesi no : 35 Taksim Istanbul 129090 , , 16,

Service

In the event of technical faults, please first check whether you can remedy the problem yourself with the help of the operating instructions (section What to do if). If you were not able to remedy the problem yourself, please contact the Customer Care Department or one of our service partners. In order to be able to assist you quickly, we require the following information: Model description Product number (PNC) Serial number (S No.) (for numbers see rating plate) Type of fault Any error messages displayed by the appliance So that you have the necessary reference numbers from your appliance at hand, we recommend that you write them in here: Model description: PNC: S No:.....

www.electrolux.com

580-00-090507-01
Subject to change without notice