English

Camcorder Parts

* Avoid blocking the strobe.
1 Focus switch 2 Microphone 3 Strap hook 4 *Record button ( ) 5 Up button (Zoom in) 6 Down button (Zoom out) 7 Button
8 Mode/ button 9 USB Port 10 TV-out Connector/ Earphone 11 SD/MMC Card Slot 12 Power Button ( Video light 13 LCD Panel
14 Speaker 15 Shutter Button ( 16 Lens 17 Video light 18 Flash strobe 19 Battery cover 20 Tripod Port

Loading the battery

Please use two AA batteries. 1. Slide open the battery compartment cover as indicated. 2. Load the batteries into the battery compartment wtih + and - ends correctly installed. 3. Replace the cover.
Inserting the SD/MMC card (optional)
1. Lift the SD card cover. 2. Insert the card in the direction of indication until it reaches the end of the slot. 3. When using a SD card, the built-in memory will become inaccessible. 4. To remove the SD card, gently push the card until it pops up.
The serial number of the le name (PICTxxxx) will be counted continuously even you delete all les on the SD card or insert a new one. If you want to restart the serial number, plese use the camcorder Format function to format the card.

Turning on the camcorder

Open the LCD panel. OR Press and hold down the Power button (

) for 3 seconds.

Turning off the camcorder
Close the LCD panel. OR Press and hold down the Power button (

Press the Power button (

) shortly will turn the video light on/off.

Setting Language

Power-on Press the Mode button Enter the Setting ( ( ) to select the Language (
) mode Use the Zoom buttons
) item Use the Zoom buttons ( button to conrm.

) to select a suitable

language and press the

Reading LCD indicators

Digital Camcorder mode:
Focus mode NightShot Smart Zoom SD card inserted Battery life Number of pictures/les Flash mode Photo resolution

Zoom ratio

Playback thumbnail mode:
Current/total recordings Play mode File type

Highlight box

Playback full mode:

Play mode

Recording time

Volume

Video REC mode:
Video light mode Focus mode NightShot Smart Zoom SD card inserted Battery life Recording Recording time Video resolution

Recording a video clip

1. Set the focus to an appropriate setting. Normally, you may set the focus to ( for most lming conditions. Select ( ) only for close-ups. 2. Press the Record button ( 3. Use the Zoom buttons ( 4. Press the Record button ( ) to start recording. ) to zoom in or zoom out the screen. ) again to stop recording. )

Taking a still picture

1. Set the focus to an appropriate setting. Normally, you may set the focus to ( ) for most lming conditions. Select ( ) only for close-ups. 2. Use the Zoom buttons ( screen. 3. Press the Shutter button ( ) to zoom in or zoom out the ) to take a still picture. 70cm ~ 50cm ~ 70cm
Playing back your recordings
1. Press the 3. Press the 5. Press the button. ) to select the Playback ( ) to shift between les. ) mode. button to enter. button to review/play the le. ) to delete les. 2. Use the Zoom buttons ( 4. Use the Zoom buttons (
Press the Shutter button (

Recording a voice clip

1. Press the 3. Press the button. ) to select the Voice ( ) to start recording. ) again to stop recording. ) mode. button to conrm. (*) 2. Use the Zoom buttons ( 4. Press the Record button (

5. When you are done, press the Record button (
When entering the Voice mode, the remaining recordable time will be displayed on the LCD.
Connecting the camcorder to a TV
Connect your camcorder and TV via the accessory AV cable for real-time display. You can display your video clips, still pictures, and audio recordings directly on your TV, sharing them with your friends and family.

AV-Mode

TV OUT

Earphone

1. Turn on your TV and switch the TV to AV mode. The TV system is different across countries. If you need to adjust the TV-out setting, please refer to page 8 for more information. (Taiwan: NTSC; America: NTSC; Europe: PAL; China: PAL)
2. Connect the audio and video ends of the AV cable to the TV. 3. Turn on the camcorder. 4. Connect the other end of the AV cable to your camcorder.
Connecting the camcorder to your PC
1. Turn on the camcorder. 2. Connect the camcorder to your computer by the USB cable.
The default is set to Disk mode. When connected to a PC, the camcorder will automatically enter Disk (Removable disk) mode. If you set the USB Mode to Menu mode, the following screen will appear.
Please select the desired connection mode. If you would like to change the setting, please refer to page 9 for more information.

Mode selection

1. Turn on the camcorder. 2. Press the 4. Press the button. ) to select the desired item. button to conrm. 3. Use the Zoom buttons (

Basic operation

How to. Move the highlight bar Conrm an item Exit menu/Go back to upper menu Action Use the Zoom buttons ( Press the Press the Mode/

) to move up or down.

button. button (when in sub-menu).
Menu items in Camera mode (1)

Power-on Press the

Item Option Picture resolution Resolution 1M 3M 6M Selftimer On/Off Auto Flash On Off * Two-in-One Histogram On/Off On/Off 1280x960 2048x1536 2848x2136

button.

Description Print photos 3x5 in. 4x6 in. or 5x7 in. 6x8 in.
Enable the selftimer. After the selftimer is turned on, the camcorder will have ten seconds delay before recording when the Shutter button is pressed. The ash automatically res when the lighting is insufcient. The ash is forced to re in every shot. The ash is disabled. This setting allows you to combine two images taken individually into one photo. The real-time histogram displays the approximate luminance distribution on the screen. You may adjust the exposure to gain better effect.
Menu items in Camera mode (2)
Item * PhotoFrame Option Description This setting allows you to add customized frames to photos. 10 background frames are available on the LCD monitor. The Photo-Frame function is disabled Set the video resolution to VGA (640x480 pixels). Set the video resolution to QVGA (320x240 pixels). Minimize blur caused by hand shake. This setting allows you to get a clearer image during using the zoom buttons. The camcorder automatically adjusts white balance. This setting is suitable for outdoor recording in sunny weather. This setting is suitable for recording in cloudy weather or shady environments. This setting is suitable for indoor recording with uorescent lamp lighting, or environments with high color temperature. This setting is suitable for indoor recording with incandescent lamp lighting, or environments with low color temperature. Make recordings in natural color. Make recordings in black and white. Make recordings in sepia-toned color. Manually adjust the exposure to gain better effect when the preview image appears too bright or too dark. A positive value indicates the image will be brighter than usual; while a negative value makes the image dimmer. This setting allows you to take a photograph with a dark background. Since the shutter speed will slow down when taking photographs at a dark place, we recommend using a tripod to eliminate blurring from hand shake. The setting allows you to add extra light when the lighting is insufcient during recording video clips

1 ~ VGA QVGA On/Off On/Off Auto Sunny
Video Stabilizer Smart Zoom
Cloudy Fluorescent Tungsten Normal

Effect

B&W Classic -2~+2

Exposure

NightShot

On/Off

Video Light
The Two-in-One and Photo-frame function will be disabled when the resolution is set to 10M.
Menu items in Playback mode
Power-on Press the Mode button Enter the Playback ( the Shutter button ( ).
Item Delete One Delete All Option Yes/No Yes/No Delete current le. Delete all pictures and video/audio les stored in the memory. Description

) mode Press

Menu items in Setting mode (1)
Power-on Press the Mode button Enter the Setting (
Item Beep Flicker Option On/Off 50Hz/60Hz NTSC TV-out PAL Icon LCD Bright Volume On/Off 0~~ 10 Enable beep sound on/off. Set icker frequency to 50Hz or 60Hz. For more information, please refer to the Flicker Settings table. Set TV system compatibility to NTSC. This option is suitable for America, Taiwan, Japan, and Korea areas. Set TV system compatibility to PAL. This option is suitable for Germany, England, Italy, Netherlands, China, Japan, and Hong Kong. Enable/disable OSD icons to display on the screen. Set LCD brightness. A greater value makes the LCD brighter; while a smaller value makes the LCD dimmer. Set the volume. (0: mute, 1-10 levels) Description

) mode.

Format

Yes No

Format the storage medium. Note that all les stored in the medium will be gone. The serial number of the le name (PICTxxxx) will be restarted. Cancel action. Set how long the camcorder will automatically shut down when staying inactive. Setting to [Off] will make the camcorder stay powered on until it runs out of power.

Auto Off

Off 1min/3min/ 5min
Menu items in Setting mode (2)
Item Language Menu USB Mode Camera Disk Start Movie Default On/Off On/Off Option Description Lets you select the language used for OSD. When connected to a PC, the camcorder displays a menu for you to choose a desired connection mode. When connected to a PC, the camcorder automatically enters Camera (PC camera) mode. When connected to a PC, the camcorder automatically enters Disk (removable disk) mode. Enable/disable the movie sequence when the camcorder is powered on. Restore factory defaults. Note that your current settings will be overridden.

Flicker Settings

Country Setting Country Setting England 50Hz Portugal 50Hz Germany 50Hz America 60Hz France 50Hz Taiwan 60Hz Italy 50Hz China 50Hz Spain 50Hz Japan 50/60Hz Russia 50Hz Korea 60Hz
Note: The icker setting is based on the frequency standard of your local power supply.

Storage Capacity

Memory SD/MMC card (128MB) SD/MMC card (256MB) SD/MMC card (512MB) SD/MMC card (1GB) Video (min.) VGA QVGA Audio (min.) Maximum 350 720
Memory SD/MMC card (128MB) SD/MMC card (256MB) SD/MMC card (512MB) SD/MMC card (1GB)
Still picture 6M 3M 1M 3080 6160
Note: The actual value of capacity may vary (up to 30%) depending on the color saturation and complexity of your subject and surroundings.

Battery Life Indicator

Icon Full battery life Moderate battery life Low battery life Empty battery life Description
Note: To avoid sudden outage of power supply, you are recommended to replace the battery when the icon indicates low battery life.

Specications

Sensor effective resolution Interpolated resolution External memory 3 Mega (2048x1536) pixels 6 Mega (2848x2136) pixels Built-in SD/MMC card slot (maximum: 2GB) JPEG (.JPG) format 2848x2136 (6 Mega) pixels 2048x1536 (3 Mega) pixels 1280x960 (1 Mega) pixels VGA (640x480 pixels) / up to 30 fps QVGA (320x240 pixels) / up to 30 fps WAVE (.WAV) format VGA (640x480 pixels) QVGA (320x240 pixels) 1.5 Color LCD 4X Yes (NTSC/PAL system) Yes Yes Yes Yes 10 seconds USB 2.0 mass storage 2 x AA Alkaline Battery F=3.0/8.31mm 86 x 72 x 36 mm

Digital still camera

Digital video camcorder Digital voice recorder PC Camera LCD display Digital zoom TV-out Built-in microphone Built-in speakers Video light Built-in flash strobe Self Timer Interface Battery Lens Dimensions
* Specifications are subject to change without notification.

Advanced Instructions

Copying les to Your PC
Installing the driver to your PC
You need to install the camcorder driver to ensure that video clips can be played back on your PC. To install the software: 1. Insert the driver CD. Turn on your computer. Then place the accessory CD into the CD-ROM drive.
Do not connect the camcorder to your computer at this stage. Shut down all other applications running on your computer. If the autorun screen does not appear automatically, double-click on My Computer and then the CD-ROM drive. Then start the Setup.exe program manually.
2. Start the installation. Click on the icon to launch the installation of the driver.
Notice for Windows 2000 users: During the installation process, a warning message regarding digital signature may appear twice or more. Please click on Yes to continue the process. The software is fully compatible with Windows 2000 operation system.

3. Install the driver.

The Install Shield Wizard will then appear and automatically install the program. Click on Next and follow the on-screen instructions to complete the installation.

Copying les to Your PC (continued)
4. Install codecs. After the driver installation is completed, the program will prompt you to install Windows Media Player Codecs. If you are not sure whether the codecs have been installed in your computer, please click on Yes and follow the on-screen instructions to complete the installation. 5. Install Direct X 9.0c or above. After the codecs installation is completed, you will be prompted to install Direct X 9.0c or above if the program is not yet installed in your computer. Please click on Yes to continue.
Windows Media Player Codecs and Direct X 9.0c or above are necessary for viewing the video clips recorded by the camcorder.
6. Restart the computer. After the installation is completed, you may need to restart your computer for the driver to take effect.
1. Turn on the camcorder. 2. Connect the USB cable to your computer. Turn on your computer, and then connect the accessory USB cable to the USB port of your computer. Make sure the cable and the port are correctly aligned. 3. Connect the USB cable to your camcorder.
Connect the other end of the USB cable to your camcorder. The default is set to Disk mode, if you would likt to set other modes as default, please refer to USB Mode section for more information.
USB mode: Power-on Press the Mode button Enter the Setting (
Menu USB Mode Camera Disk
When connected to a PC, the camcorder displays a menu for you to choose a desired connection mode. When connected to a PC, the camcorder automatically enters Camera (PC camera) mode. When connected to a PC, the camcorder automatically enters Disk (removable disk) mode.
Notice for Windows 2000/XP users: If you want to disconnect the camcorder from your computer, please follow these steps: 1. Double-click 2. Click in the system tray. (USB Disk), and then click Stop.
3. Select the camcorder when the conrmation screen appears and click OK. 4. Follow the on-screen instructions to safely disconnect the camcorder from your

File location

After connecting the camcorder to your computer, a removable disk will appear in your computer. The removable disk actually represents the storage medium of your camcorder. In the disk you can nd all of your recordings. Refer to the gure below to see where the les are stored.
For multimedia les. For MP3 les.

Using PC Camera

Installing the software
The PC camera software is included in the camera driver, and therefore you should install the driver before using the PC camera function.

Starting the application

1. Turn on the camcorder and connect the camcorder to your computer. Turn on the camcorder, and then connect the camcorder to your computer using the accessory USB cable.

2. Switch to the Camera mode
Press the button to bring up the options menu. Use the Zoom buttons ( ) to select the Camera item and press the button to conrm.
If you want to use the Video Conferencing function, please install programs such as Netmeeting to serve the purpose.
Notice for Windows 2000 users: When using the PC camera function for the rst time, the warning message regarding digital signature may appear twice or more. Please click Yes to continue the installation. The camcorder is fully compatible with Windows 2000 operation system.
3. Launch DV TS program. Double-click the DV TS icon ( ) on the Desktop to start the program. After the program starts, you can begin to use the PC camera function.
If you cannot nd the program shortcut on the desktop, you can start the program from the Programs menu.

Using DV TS PC Camera

Start recording a video clip Stop recording Snapshot Format * Source *
Start/Stop preview window Setting * Open album Select video source

* Sub-menu available.

To view pictures taken by DV TS PC Camera, please click on to open the photo album. Or, as an alternate option, go to the Work Temp folder to nd the les. The full path is as following: C:\Program Files\DV TS\Work Temp
Using DV TS PC Camera (Continued)

Recording an AVI movie

1. Click on the 2. Press AVI le. icon. to specify the path and name of the
3. Set the frame rate and recording time according to your needs. 4. Press the Start to Record button to begin recording. 5. To stop recording, click on the icon.

Taking a snapshot

Click on the icon to take a snapshot.
Conguring Format options Color Space:
Select one of the following functions according to your needs. - RGB 24: This item is for retaining better quality. - MJPG: This item indicates the AVI movie will be more compressed to gain the advantage of faster processing speed.

Output Size:

Set output size to change the size of the preview window. The default size is 320x240. Select larger pixels when you need a larger preview window.
Conguring Source options Device Control:
- Brightness: You can check the Auto item and let the program adjust image brightness for you, or uncheck the Auto item and slide the bar to adjust image brightness manually. - Quality: If the network bandwidth is congested when using PC Camera, slide the bar toward Faster Video to avoid this problem.
Conguring Flicker options
If you take your camcorder abroad, and find the screen of your computer flickers when using PC Camera function, please check the Cancel Flicker item to prevent noises from appearing on the screen. Or, you can refer to the Flicker Settings table for proper flicker value that suits the country you are staying.

Appendix: A

Troubleshooting
When using the camcorder: Problem Cause The battery is out of power. The battery is incorrectly installed. If the camcorder stays idle over one minute, the LCD screen will automatically shut down to save power. Out of memory. Can not take pictures or video clips when pressing the Shutter or Record button. The camcorder is recharging the ash strobe. Using a protected SD card. The format of the memory card is not compatible with the camcorder. The memory card is corrupted. Solution Replace the battery. Re-install the battery. Press any button except the power button to reactivate the display. Free some space from the SD/MMC card or the internal memory. Wait until the ash strobe is fully charged. Set the SD card to be writable. Use the camcorder Format function to format the card. Replace the memory card with a new one. It happens when you insert a memory card after taking a few pictures or video clips. You can access those les after removing the memory card.
The camcorder can not be powered on normally.
The camcorder is still powered on, but the LCD screen does not display.
The LCD screen displays MEMORY ERROR or CARD ERROR message. Or the camcorder cannot read the memory card.
I did not delete the pictures and video clips, but can not nd them in the memory card.
The lost recordings are saved in the internal memory.
When using the camcorder: Problem Cause If the battery icon indicates low battery, the ash strobe may be disabled due to insufcient voltage. The camcorder encounters software failure. Solution
Cannot use the ash strobe.

Replace the battery.

The camcorder does not respond to any action during operation. The recorded pictures appear too blurred.
Remove the battery pack and replace it into the compartment. Then power on the camcorder. Adjust the focus to an appropriate position. Use ash strobe when taking pictures. Add extra light sources or enable video light when recording video clips. Adjust the icker setting. For more information, please refer to the Flicker Settings table. Use the camcorder Format function to format the card.
The focus is not correctly set.
The recorded pictures or video clips appear too dark.
The environment of shooting or recording does not have adequate light.
Noises occur when viewing images on the LCD screen or on the computer. I want to restart the serial number of the le name (PICTxxxx). I convert a media le and name it as PICTxxxx.* (xxxx indicates number). Then I copy the le to the camcorder but cannot nd it on the camcorder.
The icker setting does not match the standard of the country you are staying. The counting of the serial number is handled by the camcorder rmware. There is another le with duplicate serial number (e.g. PICT0001.ASF and PICT0001.JPG), or the le type is not supported.
Give the le a distinctive serial number and make sure the le type is supported by the camcorder.

When connecting the camcorder to the computer or TV: Problem Cause Solution Install Direct X 9.0c or above and Windows Media 9.0 Codecs to solve this problem. See Installing the driver to your PC for details on installing the software, or go to http://www.microsoft.com to download the required les. Remove the driver and other related programs. Follow the installation steps in the manual to re-install the driver. Install the driver before plugging in the USB cable.
I cannot view the video clips on my computer.
Driver or software is not installed on the computer.
The installation is terminated abnormally. Driver installation failed. The camcorder has been connected to the PC via the USB cable before installing the driver. The camcorder is not correctly connected to the TV.
The TV screen does not display after connecting the camcorder to the TV.
Reconnect the camcorder to TV correctly. If you have any other camcorder or capture device installed in your computer, please completely remove the camcorder and its driver from the computer to avoid the conict. Adjust the icker setting. For more information, please refer to the Flicker Settings table.
A conict with other installed camcorder or capture device occurred.
The device is not compatible with the camcorder.
Noises occur on my computer screen when using Video Conferencing.
The icker setting does not match the standard of the country you are staying.
Country Setting Country Setting
England 50Hz Portugal 50Hz
Germany 50Hz America 60Hz

France 50Hz Taiwan 60Hz

Italy 50Hz China 50Hz

Spain 50Hz Japan 50/60Hz

Russia 50Hz Korea 60Hz

System Message

Message Recording Please Unlock SD Card No File Please Change Battery Memory Full Card Error Memory Error Strobe Is Charging File Format Error Deleting Formatting Setting
Description The camcorder is recording a le. If you insert a SD card and the card is set to Protected, this message will show up when the camcorder tries to write data into the card. When the camcorder is set to Playback mode without any existing le to play, this message will show up. The battery life of the camcorder is low. You should replace the battery with a new one immediately. The storage memory is full and can not store any more les. Please change the SD/MMC card or delete some les to free some memory space. The inserted card is not compatible with the camcorder. Please change the card or try formatting the card. The camcorder can not access data in the internal memory. Please format the medium to solve this problem. The ash strobe is charging. The le being played is not compatible with the camcorder. The camcorder is performing le deletion. The camcorder is formatting the storage medium. The camcorder is performing a setting action.

Appendix: B

Instruction for ArcSoft MediaConverter
Introduction ArcSoft MediaConverter is a powerful all-in-one multimedia le converter. This utility quickly and effortlessly converts photo, video, and music les into formats optimized for use on your portable device. Multiple les and le types can be converted at the same time. Its easy! Three simple steps are all it takes. (Please refer to Converted les section for more information.) System requirements To install and run the MediaConverter, your system must meet the following minimum requirements:
Microsoft Windows 2000/XP (Home or Professional) 50 MB free hard drive space 256 MB RAM DirectX 9 (DirectX 9c recommended) Microsoft Windows Media Player 9.0 (for converting WMA and WMV les) Microsoft Windows 2000/XP (Home or Professional) Apple QuickTime 6.5 (for converting MOV les)
Supported le formats Video Video les are converted and copied to the selected location as MPEG-4 encoded AVI les, WMV les or MPEG-4 encoded ASF les (Default). Supported le types for conversion
- AVI (Microsoft Video 1 format, Cinepak, Intel Indeo, uncompressed, etc.) - MPEG-1 in MPEG, MPG, MPE - DAT (VCD MPEG1) - MPEG-4 in AVI format - MPEG-4 in ASF - WMV - QuickTime MOV
QuickTime 6.5 and Windows Media Player 9.0 or above are required for QuickTime MOV and WMV file conversion, respectively. Supported le types for export
- AVI (MPEG-4 SP) - WMV - ASF(MPEG-4 SP)

Converted les

Step 1: Select media Adding les for conversion
1 Click the Select Media button. 2 An Open window will appear. Navigate to the folder that contains the les youd like to convert. a. Use the Files of type pull-down to lter the le types youd like to display. b. Preview highlighted les to be sure that theyre the ones you want. Check the AutoPlay box to start the playback automatically after you click a le. 3 Repeat steps 1 and 2 above until all the les you want are added. In addition to using the above method, you can also drag-and-drop les directly to the le list in the program window.
Removing les To delete a le from the list, highlight it and click the X icon.
Step 2: Select destination Click the Select Destination button to select the location where your converted files will be saved. The default save location is C:\Documents and Settings\ [current user]\My documents. However, youll most likely want to save the files to your portable device. In this case, make sure your device is connected, and then click Select Destination and choose the device.
Settings Various program settings can be accessed by clicking the Settings button. Each section lets you select one of two settings: Optimize for the selected device, and Use custom conversion settings.
Optimize for the selected device This is the default setting. The program will automatically set the conversion parameters according to your selected device. Use custom conversion settings If you decide to use this option, you can set the various conversion parameters manually.

Video settings When converting a video le, there are several different parameters:
- Resolution (Options include QVGA (320 x 240) [default] and VGA (640 x 480)) - File Format (MPEG-4 encoded AVI les, WMV les or MPEG-4 encoded ASF les) - Video Bitrate (Options include 500KB, 1.0MB, 1.5MB, 2.0 MB [default], 2.5 MB, and 3.0 MB) - Audio Bitrate (Options include 96 KB, 128 KB [default], 192 KB) - Frame Per Second (Options include [in fps] 15.00, 20.00, 24.00, 25.00 [default], and 29.97)
Selecting Optimize for the selected device uses the default values above, where applicable. After viewing/modifying the various settings, select either Save or Cancel to return to the main screen. Click Save if youd made changes that youd like to keep. Otherwise, click Cancel.
Step 3: Convert When youre ready, select (highlight) the files youd like to convert from the list, and then click the Convert button.
A progress bar will display the current status. Various popups may appear asking for specic conrmation. A popup will appear and inform you once all the les have been converted and stored to the location you selected.
Playing the converted ASF les in your camcorder To play the video clips or movies (MPEG-4 in ASF format only) converted by ArcSoft MediaConverter in your MPEG-4 digital camcorder, please follow the steps below.
Step 1 Insert a SD/MMC card in the card slot of the camcorder and connect the camcorder to PC via the USB cable. You could follow the instructions of Connecting the camcorder to your PC for more information. Step 2 Save the ASF files converted by MediaConverter on PC to your camcorder. 1 Copy the converted ASF les. 2 Open Windows Explorer to nd a Removable Disk appeared in My Computer. 3 Double-click on the icon of Removable Disk. 4 Double-click on the DCIM le folder. 5 Double-click on the 100MEDIA le folder. 6 Paste the les into 100MEDIA le folder. 7 Change the le names to CLIP****.ASF. **** could be any 4-digit number from 0001 to 9999.
The le name must follow the naming principle of your camcorder, so that the camcorder could identify the les saved on 100MEDIA.
Step 3 Now you can use the Playback ( the large LCD monitor! ) mode to enjoy the video clips or movies on
The ArcSoft MediaConverter in this package is a customized version for your digital camcorder. You may visit the website http:\\www.arcsoft.com for more product information.

Appendix: C

System Requirements
Operating System: Windows 2000/XP CPU: Pentium III or above System RAM: 128MB or above Graphic Card: 64MB, 24 bit true color CD-ROM speed: 4x or above Software: Direct X 9.0c or above and Windows Media Player Codecs Other: USB connector