OPERATING INSTRUCTIONS

42 Widescreen Plasma HDTV Monitor

PDP4273M

1. Safety Guidelines
Caution: Always use a power cable is properly grounded. Please use the AC cords listed below for each area: USA. UL Canada. CSA/cUL FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference will not occur in a particular installation. If this equipment does cause by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio technician for help.
FCC Warning To assure continued FCC compliance, the user must the provided grounded power supply cord and the provided shielded video interface cables to connect to this equipment. Also, any unauthorized changes or modications to this equipment would void the users authority to operate this device.
BBE is trademark of BBE Sound, Inc. Manufactured under license from BBE Sound, Inc. Licensed by BBE Sound, Inc. under USP4638258, 5510752 and 5736897. BBE and BBE symbol are registered trademarks of BBE Sound, Inc. BBE High Denition Sound restores clarity and presence for better speech intelligibility and musical realism.
HDMI, the HDMI logo and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

2. Important Safeguards

Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or re. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of the product. Read the following safety instructions before starting the operation. The User Manual uses the following symbols to ensure a safe operation and prevent any damage to operators or properties: WARNING----- Ignorance or inappropriate use may cause damage to the product. ATTENTION---Ignorance or inappropriate use may cause injury to the user. Examples: Prohibition Warning (Attention) symbol (indicating Electric Shock).
WARNING Do not install the product on sloping or unstable surface: The product may drop or tip over. Only the marked power source can be used for the product: Any power source other than the specied one may cause re or electric shock. Keep the product away from moisture: - Do not expose this appliance to rain or moisture. - If water penetrates into the product, stop the operation; unplug the connector and contact with your dealer. Continuous use in this case may result in re or electric shock. WARNING Do not place any objects on the top of the product: Spilled water or metal objects may cause short circuit, re or electric shock if they penetrate into the housing of the product.
Never use a damaged power cord: Heavy objects, heat or tensile force may damage the power cord and cause re or electric shock. Do not change or open the back cover: Removing the back cover of the product may cause re or electric shock. Contact the manufacturer when inspection or adjustment is required. Do not use the product if any abnormality occurs: If any smoke or odor becomes apparent, unplug the connector and contact the manufacturer immediately. Do not try to repair the product by yourself. WARNING Avoid using dropped or damaged appliances: If the product is dropped and the housing is damaged, the internal components may function abnormally. Unplug the connector immediately and contact the manufacturer for repair. Continuous use of the product may cause re or electric shock. WARNING Do not touch the power cord during lightening: To avoid electric shock, avoid handling the power cord during electrical storms. ATTENTION Do not install the product close to smoke or moisture: Fire or electric shock may be caused when the product is installed close to smoke or moisture. Do not installed the product in an area with heavy dust or high humidity: Fire or electric shock may be caused when the product is installed in a place with heavy dust or high humidity. Instructions for moving the product: Ensure that the power connector and any other leads are unplugged before moving the product. The power cable should be kept away from heat sources: The heat produced by any heat source may melt the covering of the power cable.

Unplug the connector Hold the power connector when removing the power cable: Pulling the power cable itself may damage the wires inside the cable and cause re or electric shock. Do not touch the connector with wet hands: To avoid risk of electric shock.
ATTENTION Insert batteries in accordance with instructions: Insert the batteries with correct polarities (positive and negative Incorrect polarities may cause breakage and leakage of the batteries, hurt operators and contaminate the remote controller. ).
Do not block or cover the vents: Blocking the vents may cause overheating and re. Do not install the product in a place with little or no ventilation. Never cover the vents with towels, blankets or dusters. Unplug the connector: Unplug the power connector when the product will not be used for a long time.

Unplug the connector

Image Sticking: The plasma monitor illuminates phosphor to display images. The phosphor has a nite illumination life. After extended periods of illumination, the brightness of the phosphor will be degraded to such extent that stationary images would burn-in that part of the screen as grayed-out images. Tips to prevent such image sticking are: - Do not display static images of high contrast and high brightness for long periods. Use of video games and computers on this product may promote burn in of images on the screen. Many portions of video game play and computer desktops do not refresh and will contribute to this problem. - Do not leave stationary images appearing for long, but try to refresh them at appropriate intervals of time, or try to move them using screen saver function. - Turn down the contrast and brightness control. Note: Such Image Sticking constitute misuse are NOT COVERED by the manufacturers warranty. Others: This product is designed for indoor use only and is not suitable for out door use. The operation temperature is 5C ~ 33C.
1. Read all safety instructions and the User Manual before using the product. 2. The safety instructions and User Manual should be maintained in good condition for future reference. 3. Unplug the power connector before cleaning the product. A wet cloth is sufcient for the cleaning of the product, never use liquid or spray cleaner for cleaning the product. 4. Always use the accessories recommended by the manufacturer to avoid any risk. 5. When moving the product from an area of low temperature to an area of high temperature, drops of water may condense on the housing. Do not turn on the display immediately after moving so as not to cause re, electric shock or component damage. 6. Do not install the product on unstable xtures or stands. The installation of the product should be conducted in accordance with the instructions and using the support recommended by the manufacturer. 7. Do not remove the earthing pin on the power plug. The product is supplied with a three-pin earthing-type power plug, this plug will only t an earthing-type power outlet. This is a safety feature, if you are unable to insert the plug into the outlet, contact an electrician. 8. Avoid overloading the power cord. Using extension cables or the cords of other appliances may cause re or electric shock. 9. If any of the following occurs please contact the retailer: - The power supply or connector fails. - Liquid sprays or any object drops into the Display. - The Display is exposed to rain or other moisture. - The Display is dropped or damaged in any way. - The performance of the Display changes substantially. 10. A distance of at least 1 meter should be maintained between the product and any heat source, i.e. radiator, heater, oven, amplier etc. 11. To avoid the risk of electric shock or component damage, switch off the power before connecting the PDP to other devices, such as VCR, DVD or PC. 12. The power cable must be replaced when using different voltage from that specied in the User Manual. For more information, contact your dealer. 13. Operating environment: Temperature: 5C~33C Humidity: 20% to 85% non-condensing Atmospheric pressure: 800 to 1100hPa

Contents

1. Before use.... 7
1.1 Open the Package....7 1.2 Installation....7
2. Product Features... 8 3. Accessories... 8 4. Names and Functions of Parts... 9
4.1 Side View...9 4.2 Front View....10 4.3 Rear View....11 4.4 Remote Control....12
5. Connection to External Equipment.. 15 6. Basic Operation... 18
6.1 Power ON/OFF....18 6.2 Selection of Input Mode...18 6.3 Other Function...19 6.4 OSD Option Adjustment...20 6.5 OSD Functions...20
1 Picture Page....Window Page....Audio Page....Options Page....Layout Page....30
7. Technical Specication... 32 8. Support the Signal Mode.... 33 9. Cleaning and Simple Troubleshooting.. 34

1. Before use

The product is a 42 WXGA (WXGA resolution) Plasma Display. It has passed the Class-B EMC test and the UL and cUL safety certications, and is ideal for both consumer and commercial use. The product is a precise electronic product. Users should read the following instructions carefully to maximise the performance of the product:

1.1 Open the Package

- The product is packaged in a carton together with other standard accessories. Any optional accessories shall be packed separately in another carton. - Due to the size & weight of the product, it is recommended that it should be moved by a minimum of two people. - The protective glass and the glass substrate are installed on the front of the product. Since both glasses can be broken and scraped easily, move the product gently. Never place the unit with the glass facing downwards unless it is protected with soft pads. - When opening the carton, check that the product is in good condition and that all standard accessories and items are included. - Whenever possible, use the handles on the back of the Display for transport. - Please use caution if wall mounting this product. Follow all directions from the manufacturer of the wall mount and be sure to securely fasten the product to the mount. While the TV can be wall mounted, improper wall installation may void the warranty. - Due to the higher power consumption, always use the jack exclusively designed for this product. If an extended line is required, please consult with your service agent. - The product should be installed on a at surface to avoid tipping. The distance between the back of the product and the wall should be maintained for proper ventilation. - Avoid installing the product in the kitchen, bathroom or any other places with higher humidity so as not to shorten the service life of the electronic components. - Please ensure the product be installed horizontally, any 90 degree clockwise or counterclockwise installation may induce poor ventilation and subsequent component damage. - To protect the screen and avoid screen burn, do not hold on a static picture for a long time.

4.4 Remote Control

1 Standby( ): Press this button to turn off to standby and turn on from standby. 2 Mute( ): Press this button to quiet the sound system. Press again to reactivate the sound system. 3 Number buttons: Use these buttons to enter the password. 4 PIP POS. : Press the button to select different Image Position in PIP Mode. 5 Source: Press this button and use / button to select the signal sources. AV, S-Video, YPbPr 1, YPbPr 2, VGA or HDMI. 6 Layout: Press this button to pop up Layout menu. 7 Swap: Press this button to switch the Main window or Sub window pictures in PIP and Split Screen. 8 VOL +/- : Press these buttons to increase or decrease the volume. 9 W. Sele: Press this button to select the Main Window or Sub Window. 10 S. Sele: Press this button to select the sound output from Main Window or Sub Window. 11 PIP: Press this button to change different Picture Mode. 12 OK : Press to enter or conrm. / : They are used as / buttons in the OSD Menu screen. / : They are used as / buttons in the OSD Menu screen. They also can be used for the selection of the program when the OSD Menu is not shown on the screen, but only for the Model with Tuner. (Continued on next page)
13 Auto: The Display automatically adjusts the phase, vertical / horizontal position when pressing this button in VGA mode. 14 Menu: Press this button to pop up the OSD Menu and press it again to exit the OSD Menu. 15 V-Chip: Press this button to enter the V-Chip Function. (Only for AV or S-Video) 16 P. Still: Press this button to hold on the screen. Press again to normal. 17 C/C: Press this button to enter the Closed Caption Function. (Only for AV or S-Video) 18 Display: Press the button to display the source information. 19 Sound: Press the button to select different sound effect. 20 Time: Press this button to pop up the Clock Set menu. 21 P. Size: When the input source is YPbPr 1, YPbPr 2, VGA or HDMI, press this button, the picture will change according to Fill All, Force 4:3, Letter Box, Wide or Anamorphic. When the input source is AV or S-Video, press this button, the picture will change according to Fill All, 4:3, Letter Box, Wide or Anamorphic. 22 PIP Size : Press the button to select different Image Size in PIP Mode. 23 P. Mode : Press the button to select different picture effect. 24 F. White: Press this button to show a full white picture. 25 Sleep: Press this button to select the sleep time.

DVI AUDIO

red white
Connect audio amplier or other TV set (Only for AV) 1. Connect audio amplier apparatus or other TV set that with audio input. 2. Connect the composite video output terminal to the video output terminal of the video input device.
Connecting the DVD, VCR or other video apparatus 1. With an S-VIDEO cable connect the PDP to the VCR or other device. S-VIDEO will connect only the video portion (image only) of the signal. With an AUDIO cable (RCA type) connect the AUDIO OUT from the device to the AUDIO IN on the PDP. 2. With an AV cable connect to the Video plug of the PDP and the VCR or other video apparatus. With an AUDIO cable connect the audio output of the VIDEO of the VCR or other video apparatus to the audio input of the VIDEO of the PDP. 3. Please ensure the Power Cord is connected and turn on Power Switch button before it is operated. 4. Press STANDBY button to turn on the PDP. 5. To watch the VCR or other video apparatus, please press SOURCE button to select S-VIDEO or AV.

red red white

VCR etc.

6. Basic Operation

6.1 Power ON/OFF: The Display is in Standby mode
- Press Standby ( ) button on the remote control or on the front panel to turn on the unit. The power indicator changes from red to green. - Press Standby ( ) button on the remote control or on the front panel again to return the display to standby mode. The power indicator changes from green to red. Note: For protecting your PDP product, the interval time between turn on the PDP product and shut down it should be kept at least one minute.
6.2 Selection of Input Mode
- Press Source button on the remote control or on the front panel. A menu of input signal sources shall appear. Press or to select the signal source you desired and press OK / to conrm the selection. The signal sources are displayed in the following sequence:

Source Select:

AV S-Video YPbPr 1 YPbPr 2 VGA HDMI
When select the input source, the screen will display the direction.
AV Searching Fill All AV NTSC 60Hz/3.58 MHz
When there is no signal from the selected source (see illustration), either change the channel or press Source button to change sources. If there is no signal on your selected source for 15 minutes the television will power down.

the front panel

OK Menu

SOURCE MENU

6.5 OSD Functions
1 Picture Page [Input source is YPbPr 1, YPbPr 2, VGA or HDMI signal] - Press Menu button, then press or button to choose the Picture item. - Press or button to select Brightness, Contrast, Saturation (only for YPbPr 1 and YPbPr 2), Phase (only for VGA), Peaking (only for YPbPr 1, YPbPr 2 and HDMI), Frequency, Picture Mode or Color Temp, then press OK or button to enter. - Press or button to adjust; - Press Menu button to exit Sub Menu or Main Menu. Note: When the signal source is HDMI, you cant adjust Phase and Frequency.
Items (press / button) Brightness Contrast Saturation Phase Peaking Frequency Picture Mode Color Temp
Adjust (press / button) Decrease / Increase Decrease / Increase Decrease / Increase Decrease / Increase Choose Normal, Sharp or Sharpest Decrease / Increase Choose Choose
Adjust Effects Darken / Brighten Reduce / Enhance Only for YPbPr 1 and YPbPr 2 Only for VGA Only for YPbPr 1, YPbPr 2 and HDMI Reduce to left / Widen to right Choose Normal, Bright, Cinema or User Choose Warm, Normal or Cool
[Input Source is AV or S-Video signal] Press Menu button, then press or button to choose the Picture item. Press or button to select Brightness, Contrast, Saturation, Tint (only for NTSC), Sharpness, Picture Mode or Color Temp, then press OK or button to enter. Press or button to adjust; Press Menu button to exit Sub Menu or Main Menu. Adjust (press / button) Decrease / Increase Decrease / Increase Decrease / Increase Decrease / Increase Decrease / Increase Choose Choose Adjust Effects Darken / Brighten Reduce / Enhance Decrease / Increase Picture Color Bias Green / Bias Red Picture Gentleness / Sharpness Choose Normal, Bright, Cinema or User Choose Warm, Normal or Cool
Items (press / button) Brightness Contrast Saturation Tint Sharpness Picture Mode Color Temp
Hot keys: - Press P. Mode button to pop up the menu, then press / or P. Mode button to select Normal, Bright, Cinema or User.
2 Window Page [Input source is YPbPr 1, YPbPr 2, VGA or HDMI signal] - Press Menu button, then press or button to choose the Window item. - Press or button to select Image Size, H Position, V Position, H Resolution or Freeze Window, then press OK or button to enter. - Press or button to adjust; - Press Menu button to exit Sub Menu or Main Menu. Note:1. When the signal source is HDMI, you cant adjust H Resolution. 2. In VGA,YPbPr 1 or YPbPr 2 signal source, when select Fill All in Image Size item, you can adjust H Resolution. Items (press / button) Image Size H Position V Position H Resolution Freeze Window Adjust (press / button) Choose Decrease / Increase Decrease / Increase Decrease / Increase Choose Adjust Effects Choose Fill All, Force 4:3, Letter Box, Wide or Anamorphic Picture Left / Right Move Picture Down / Up Move

Picture Left and Right Shrink / Broaden

Choose Off or On

[Input Source is AV or S-Video signal] - Press Menu button, then press or button to choose the Window item. - Press or button to select Image Size or Freeze Window, then press OK or button to enter. - Press or button to adjust; - Press Menu button to exit Sub Menu or Main Menu. Items (press / button) Image Size Freeze Window Adjust (press / button) Choose Choose Adjust Effects Choose Fill All, 4:3, Letter Box, Wide or Anamorphic Choose Off or On
Hot keys: Image Size - When the input signal source is YPbPr 1, YPbPr 2, VGA or HDMI, press P. Size button to pop up the menu, then press / or P. Size button to select Fill All, Force 4:3, Letter Box, Wide or Anamorphic. - When the input signal source is AV or S-Video, press P. Size button to pop up the menu, then press / or P. Size button to select Fill All, 4:3, Letter Box, Wide or Anamorphic.
Freeze Window - When the program information you want to capture is displayed, press P. Still button on the remote control. The picture freezes. Press P. Still button again, and the frozen picture is released, and the picture begins to move again.

Freeze

3 Audio Page 3.1 Adjust Sound Effects - Press Menu button, then press or button to choose the Audio item. - Press or button to select Balance, Audio Mode, AVC or Equalizer, then press OK or button to enter. - Press or button to adjust; - Press Menu button to exit Sub Menu or Main Menu. - When you adjust Equalizer, press or button to select 120Hz, 500Hz, 1.5kHz, 5kHz or 10kHz, then press or button to adjust the items needing. Note: When select User in Audio Mode item, you can adjust Equalizer. Items (press / button) Balance Audio Mode AVC Equalizer Adjust (press / button) Decrease / Increase Choose Choose Off or On Adjust Effects Left / Right Channel Gradual Decrease / Increase Choose BBE, Cinema, Music, News or User AVC (Automatic Volume Correction) Off or On
Press OK / button to conrm Adjust Equalizer
Hot keys: Audio Mode - Press Sound button, it will pop up the Audio Mode item, then press / or Sound button to select BBE, Cinema, Music, News or User.
3.2 Selecting MUTE on / off - Press Mute button, the icon will appear on the screen and the system is mute; - Press Mute button again, sound continues.
3.3 Adjust Volume - Pressing VOL. on the front panel or / on the remote control, a bar showed on the screen to adjust volume which the number scales and volume gradually increase or decrease. - Press VOL. on the control panel or / buttons on remote control once, volume increases or decreases a scale correspondingly.

4 Options Page - Press Menu button, then press or button to choose the Options item. - Press or button to select Osd Timeout, Menu Background, Language, Default Setting, Close Caption Mode, Close Caption, Content Blocking or Timer, then press OK or button to enter. - Press or button to adjust; - When you select Default Setting, press OK or button to enter and show Default Setting. - Press Menu button to exit Sub Menu or Main Menu. Note: When the signal source is YPbPr 1, YPbPr 2, VGA or HDMI, you cant adjust Close Caption Mode, Close Caption or Content Blocking. Items (press / button) Adjust (press / button) Choose 5 Sec, 15 Sec or 60 Osd Timeout Sec Menu Background Choose Opaque / Translucent Language Default Setting Close Caption Mode Close Caption Content Blocking Timer Adjust Effects Adjust show time of OSD on the screen. Adjust OSD menu background. Choose English, French or Choose Spanish. Some adjusted items go back Press OK / button to conrm to original factory settings. Choose CC1, CC2, T1, T2 or Choose Xds. Choose Press OK / button to conrm Press OK / button to conrm Pop up the Clock Set menu. Choose Off, On or On Mute.
- When you select Timer, press OK or button to enter. - Press or button to move the bit, press or button to adjust. You can set the timer three ways: a. Set the Wake Up Time only b. Set the Sleep Time only c. Set the Sleep Time and Wake Up Time Note: 1. After you set the timer, you must press Standby button to put the PDP in the standby mode. 2. The setting is valid, you must set On in Timer.
Hot keys: - Press Time button to show the Timer menu, then you can set Clock Set, Timer, Wake Up Time or Sleep Time. The operation is as same as above. Sleep Time function - Press Sleep button to select 15 Minutes, 30 Minutes, 45 Minutes, 60 Minutes, 75 Minutes, 90 Minutes, 105 Minutes, 120 Minutes or Off. Note: With these functions, the PDP will be turned on or off at the set time automatically. 1. Before you use these functions, please set the time of Clock Set to the current time. The Wake Up Time and Sleep Time base on the Clock Set you set. 2. Turn off the PDP by Power Switch will cancel the Clock Set, Timer, Wake Up Time or Sleep Time settings. 3. Turn off the PDP by Power Switch or set Off by Sleep button will cancel the Sleep Time settings. [Input Source is AV or S-Video] You can set CC (Close Caption) as the following operation: - Press Menu button, then press or button to choose the Options item. - Press or button to select Close Caption Mode or Close Caption, then press OK or button to enter. - Press or button to adjust; - Press Menu button to exit Sub Menu or Main Menu. (Continued on next page)

Hot keys: - Press C/C button to pop up Close Caption Mode item, then press or button to choose CC1, CC2, T1, T2 or Xds.
You can set Content Blocking as the following operation: - Press Menu button, then press or button to choose the Options item. - Press or button to select Content Blocking, then press OK or button to enter and show Enter Password (Initial Password is 0000). - Use 0~9 buttons to enter the password, then press OK button to enter Content Blocking setting.

Enter Password ---OK

Note: Before setting for Change, Movie Block and TV Block, the correct block password is required to input. If the input is invalid, the Password Error menu will pop up, as the following illustration; Enter Password - - - OK Enter Password - - - OK

Password

(Continued on next page)
Note: The initial password for the system is 0000. Please operate Change at the rst time. If you had forgotten the password, please contact with service centre. Change Blocking Password - Press or button to select Change in Sub Menu, then press OK or button to pop up Enter New Password. - Use 0~9 buttons to enter your new password. - Press OK button to conrm and pop up Conrm Password. - Use 0~9 buttons to enter your new password again. - Press OK button to conrm. - Press Menu button to exit Sub Menu or Main Menu.
Enter New Password - - - OK Conrm Password - - - OK
V-Chip Enable - Press or button to select V-Chip Enable in Sub Menu, then press / button to select On or Off. - Movie Block and TV Block, these functions are activate, while V-Chip select On. - Movie Block and TV Block, these functions are inactivate, while V-Chip select Off. - Press Menu button to exit Sub Menu or Main Menu. Movie Block - Press or button to select Movie Block in Sub Menu, then press OK or button to pop up Movie Content Blocking Menu. - Press or button to select G, PG, PG 13, etc. - Press OK button to lock (display ) or unlock (doesnt display ). - When display , you can not watch the programs. - When doesnt display , you can watch the programs. - Press Menu button to exit Sub Menu or Main Menu.
Items G PG PG 13 R NC 17 X NR
Description and Content themes General Audience (Appropriate for all ages). Parental Guidance Suggested (Some material may not be suitable for children). Parents Strongly Cautioned (Some material may be inappropriate for children under 13). Restricted (Under 17 requires accompanying parent or adult guardian). Not intended for anyone 17 and under. X-rated (For adults only). No rating (Blocks all viewing).
TV Block - Press or button to select TV Block in Sub Menu, then press OK or button to pop up TV Content Blocking Menu. - Press , , or button to select Y, Y7, G, etc. - Press OK button to lock (display ) or unlock (doesnt display ). - When display , you can not watch the programs. - When doesnt display , you can watch the programs. - Press Menu button to exit Sub Menu or Main Menu.

Items Y

Description and Content themes All Children (This program is designed to be appropriate for all children). Directed to Older Children (This program is designed for children age 7 and above). Note: Programs in which fantasy violence may be more intense or more combative than other programs in this category are designed TV-Y7. General Audience (Most parents would find this program suitable for all ages). Parental Guidance Suggested (This program contains material that parents may nd unsuitable for younger children). D Some suggestive dialog L Infrequent coarse language S Some sexual situations V Moderate violence Parents Strongly Cautioned (This program contains some material that may parents would nd unsuitable for children under 14 years of age). D Intensely suggestive dialog L Strong, coarse language S Intensely sexual situations V Intense violence Mature Audience Only (This program is specically designed to be viewed by adults and therefore may be unsuitable for children under 17). L Crude or indecent language S Explicit sexual activity V Graphic violence
Temporary cancel V-Chip function - If you want to watch the lock programs, you can enter the password and temporary cancel V-Chip function only for current program. - In the current program source, after the temporary cancel V-Chip function, cant operate from On to Off function of the V-Chip Enable in the OSD menu. Hot Key: - Press V-Chip button to enter the V-Chip menu directly, and the operation is as same as above. 5 Layout Page - Press Menu button, then press or button to choose the Layout item. - Press or button to select Full Screen, PIP or Split Screen, then press OK or button to enter. - Press Menu button to exit Sub Menu or Main Menu. Items (press / button) Full Screen PIP Split Screen Adjust (press / button) Press OK or button to enter Press OK or button to enter Press OK or button to enter Adjust Effects Full Screen Mode PIP Mode Split Screen Mode (Continued on next page)
* You can view program in a variety of picture layout: Full Screen, PIP, Split Screen picture, and them showed as following: Hot keys: - Press PIP button to display in the following sequence (circular display). Full screen picture PIP picture Split Screen picture
Hot keys: - Press Layout button, then press or button to select Full Screen, PIP or Split Screen, press OK button to change.

Items Signal

PIP/Split Screen Main AV/S-Video YPbPr 1/YPbPr 2/VGA/HDMI Sub
YPbPr 1/YPbPr 2/VGA/HDMI AV/S-Video

7. Technical Specication

Product Model VIDEO System Screen Size Display Area Aspect Radio Dimension Net Weight Display Resolution Pixel Dot Pitch Color Gray Scale Brightness(Peak Value) Contrast Ratio Sound Effect Power Supply Power Consumption Input Terminal PDP4273M NTSC / PAL M 42 Wide screen 920.1mm (W) x 518.4mm (H) 16:9 1039.8mm (W) x 719.9mm (H) x 109.5mm (D) (w/o stand and handles) 1039.8mm (W) x 757mm (H) x 286mm (D) (with stand and handles) 41 kg (with stand, speaker and handles) 1024(H) x 1024(V) Pixels (Each pixel has R/G/B 3 color cells) 0.900 (H) x 0.510 (V) mm 16.7 millions of colors (R/G/B each 256 scales) 256 (R/G/B each 8-bit) Typical 1400cd/m2 (Panel Only) Typical 3000:1, In a dark room (Panel only) BBE System AC 100~120V, 60 Hz 330W Typical VGA (D-Sub 15 Pin Type) x 1 RS-232 (D-Sub 9 Pin Type) x 1 HDMI (Ver. 1.1) connector x 1 S-Video (Mini Din 4 Pin) x 1 Video (RCA Type) x 1 YPbPr 1 x 1 YPbPr 2 x 1 Stereo, Audio x 6 Audio ( L + R ) x 1, Video (RCA Type ) x 1, SPDIF (Optical) x1 UL/cUL/FCC

Output Terminal Agent System
NOTE: The specications shown above may be changed without notice for quality improvement.
8. Support the Signal Mode
A. VGA Mode, HDMI Mode or HDTV Mode (YPbPr 1 or YPbPr 2) Horizontal Frequency (kHz) 31.50 37.90 48.40 31.468 45.00 33.75 15.734 31.468 45.00 33.75 Vertical Frequency (Hz) 60.00 60.32 60.00 59.94 60.00 60.00 59.94 59.94 60.00 60.00 Dot Clock Frequency (MHz) 25.18 40.00 65.00 27.00 74.25 74.25 13.50 27.00 74.25 74.25
Resolution 640 x x x 768 480p 720p 1080i 480i 480p 720p 1080i

HDMI Mode

HDTV Mode (YPbPr1/YPbPr2)
B.PIP/PBP Screen Mode Items Main Large Sub Middle Small Main Sub VGA x x x x x x HDMI/YPbPr1/YPbPr2 720p 1080i 480p OK OK OK OK OK OK X OK OK X OK OK OK OK OK OK OK OK
Note: - X means out of range (can not show). - When the signal received by the Display exceeds the allowed range, a warning message shall appear on the screen. - You can conrm the input signal format from the on-screen.
9. Cleaning and Simple Troubleshooting
1 Important: - Make sure that the power cable is removed from the AC outlet before cleaning the product. - Do not use volatile solvent (such as toluene, rosin and alcohol) to clean the Display. Such chemicals may damage the housing, screen glass and remote control, and cause the paint to peel. 2 Cleaning of Housing and Remote Control: - Use a soft cotton cloth for cleaning. - If the housing or remote control are seriously contaminated, use a soft cloth moistened with diluted neutral clean the Display. Wring water out of the cloth before cleaning to prevent water from penetrating into the housing. Wipe the Display with a dry cloth after cleaning. 3 Cleaning of Screen: - Use a soft cotton cloth to clean the screen gently. - The screen glass is very fragile; so do not scrape it with any sharp object. Do not press or tap the screen to avoid cracking. When the screen is seriously contaminated, use a soft cloth moistened with diluted neutral cleaner to clean the Display. Wring water out of the cloth before cleaning to prevent water from penetrating into the housing. Wipe the display with a dry cloth after cleaning. 4 Simple Troubleshooting: If the display fails or the performance changes dramatically, check the Display in accordance with the following instructions. Remember to check the peripherals to pinpoint the source of the failure. If the Display still fails to perform as expected, contact the dealer for assistance.

The trouble status Power cannot be turned on. (Power indicator does not light) No Input Signal message appears.
The way of shooting - Check that both ends of the power cable are plugged into the socket appropriately. - Check that the signal line is connected properly. - Check that the power of the relevant peripherals is turned on. - Check that the Input option that has been selected matches with the input signal. - Check that the polarity of the batteries are correct. - Check that the batteries are not drained. (Use new batteries.) - Check that the Remote Control is within the operating range. - Check that the Remote Control is pointed to the Remote Control Window on the Display. - Check that there are no obstacles between the Remote Control and the Remote Control Window. - For more information about the Remote Control, refer to Chapter 6. - Check that there is no emitter sources (Car, HV cable or Neon lamp) or other possible interference sources. - Check that all the video settings are adjusted appropriately, such as brightness, contrast, color etc. - For more information about video settings, refer to OSD Functions in Chapter 6. - Check that the screen position and size is adjusted appropriately. - Check that the signal line is connected properly. - When connecting to PC, you can change the resolution of PC to acquire correct image. The discrepancy of the PC output signal may affect the display of the image. - Check that the speaker (audio) cables are connected appropriately. - Check that the Display is not in the Mute mode. - Check that the audio signal lines from the peripherals are connected properly. - Select the correct input signal. - For more information, refer to Support the Signal Mode in Chapter 8.
The remote control does not function properly.
Flashing spots or stripes appear on the screen. Image color or quality deteriorates. Screen position and size are incorrect. Image or color is incorrect.
The external speaker has no sound. Check that the input signal line is properly xed, or display warning message.