6 / 198

Alcatel SpeedTouchHome/Pro CLI Navigation

7 / 198

8 / 198
Accessing the Command Line Interface
Users can access the Command Line Interface via: " A Telnet session This requires that TCP/IP connectivity exists between the host from which the Telnet session is opened and the SpeedTouchtHome/Pro " The serial 'Console' interface, if equipped.
Access via a Telnet Session or Serial Console
As soon a session to the CLI is opened, the SpeedTouchtHome/Pro banner pops up, followed by the CLI prompt. In case of a Telnet session authentication via the System password might be required before access is granted. The following figure shows an example of the SpeedTouchtHome/Pro banner after opening a Telnet session and authentication. EXAMPLE:
/home/doejohn{1}$ telnet 10.0.0.138 Trying 10.0.0.138. Connected to 10.0.0.138. Escape character is ^]. User : SpeedTouch (0090D000012345) Password : ###### * * ______ * ___/_____/\ * / /\\ Alcatel Speed Touch * _____/__ / \\ ADSL Modem/Router * _/ /\_____/___ \ Version R3.2 * // / \ /\ \ * _______//_______/ \ / _\/____ Copyright (c) 19992001 Alcatel * / / \ \ / / / /\ * __/ / \ \ / / / / _\__ * / / / \_______\/ / / / / /\ * /_/______/___________________/ /________/ /___/ \ * \ \ \ ___________ \ \ \ \ \ / * \_\ \ / /\ \ \ \ \___\/ * \ \/ / \ \ \ \ / * \_____/ / \ \ \________\/ * /__________/ \ \ / * \ _____ \ /_____\/ * \ / /\ \ /___\/ * /____/ \ \ / * \ \ /___\/ * \____\/ * =>

9 / 198

Navigation and Manipulation
Manipulation commands are commands that manipulate operations on the command line, for example changing the command group, go to the beginning of the command line, go to the end of the command line, etc.

Command group Navigation

From top level, you can change to a command group by executing the name of the desired command group. To obtain a list of all available command groups, execute help from the top level.
EXAMPLE (SpeedTouchtHome):
=>help Following command groups are available : config system software ip adsl pptp bridge atmf dns dhcp => phonebook td
EXAMPLE (SpeedTouchtPro):
=>help Following command groups are available : config system software ip adsl nat cip ppp bridge atmf td dns => phonebook pptp dhcp
To return to top level, execute exit.

EXAMPLE:

=>phonebook [phonebook]=> [phonebook]=>exit =>

10 / 198

The Help Command
Execute help from top level to list all available command groups for the SpeedTouchtHome/Pro. EXAMPLE (SpeedTouchtPro):

=>help Following command groups are available : config system software ip adsl nat cip ppp bridge atmf td dns dhcp dns td atmf =>

phonebook pptp dhcp mer

You can execute the help command from each command group selection. This results in a list of the available commands (and nested command groups, if available) in this particular command group. EXAMPLE:
=>phonebook [phonebook]=> [phonebook]=>help Following commands are available : list add delete load autolist help [phonebook]=>

save exit

Executing e.g. help phonebook from top level gives the same result as executing help from the phonebook command group selection. EXAMPLE:
=>phonebook help Following commands are available : list add delete load autolist help =>

11 / 198

Entering help followed by a specific command, e.g. help phonebook add (starting from top level) or help add (e.g. on the phonebook command group selection) results in a description of the syntax for the command. EXAMPLE:
=>help phonebook add add : Adds a phonebook entry name=<string> addr=<vp*vc> type=<bridge|ppp|cip|pptp> =>

Command Completion

The CLI features command completion, which means that when starting to enter a command it can be completed by pressing the Tab" key. For example, entering a at the firewall command group selection, followed by a Tab" stroke results in the full assign command being completed. Entering firewall a from top level gives the same result. For the completion to be successful, the part to be added must be unique. Completion works for the command groups, for the commands, for the options, but not for values. EXAMPLE:
=>phonebook [phonebook]=>d Tab [phonebook]=>delete
Going to the beginning or end of the Command Line
Go to the beginning of the Command Line by pressing "Ctrl+A"; to go to the end of the Command Line press "Ctrl+E". In the following example, the first indicates the position of the cursor after pressing "Ctrl+A", the second the position of the cursor after pressing "Ctrl+E". EXAMPLE:

=>list

Breaking off Commands

12 / 198

You can break off a command by pressing Ctrl+G". This can be useful in a situation where a user is prompted to enter a value which it does not know and wants to abort the command. Instead of being prompted over and over again for the same value, this allows to break of the command. In the example below Ctrl+G" is pressed after the third prompt `name =`. The command is broken of and the user returns to the command line. EXAMPLE:

[phonebook]=>add name = name = name = Ctrl+G" [phonebook]=>

History of Commands

To retake previous commands press the up arrow   and come back to more recent commands with the down arrow  . Press Enter ()" to select and execute the retaken command. EXAMPLE:
=>phonebook [phonebook]=>list Name address Br1 8*35 Br2 8*36 Br3 8*37 Br4 8*38 RELAY_PPP1 8*48 RELAY_PPP2 8*49 RELAY_PPP3 8*50 RELAY_PPP4 8*51 PPP1 8*64 PPP2 8*65 PPP3 8*66 DHCP_SPOOF 8*67 CIPPVC1 8*80 CIPPVC1 8*81 CIPPVC3 8*82 CIPPVC4 8*83 [phonebook]=>   [phonebook]=>:phonebook list
type bridge bridge bridge bridge pptp pptp pptp pptp ppp ppp ppp ppp cip cip cip cip
usage configured free free free configured configured configured configured configured configured free configured configured free free free

13 / 198

Command Line Interface Top Level Structure
The following command groups are available:
" " " " " " " " " " " " " " "
adsl (only applicable for the SpeedTouchtHome/Pro ADSL/POTS variants) atmf (only applicable for models equipped with an ATMF25.6Mbps port) bridge cip (only applicable for the SpeedTouchtPro) config dhcp dns ip nat (only applicable for the SpeedTouchtPro) phonebook ppp (only applicable for the SpeedTouchtPro) pptp software system td

14 / 198

Command Line Interface Commands
All CLI commands are commands that operate on, or configure, the SpeedTouchtHome/Pro. You can execute these commands from top level, preceded by the name of the command group from which the command should be executed (e. g. phonebook list). You can also execute the commands from the command group itself, using the reduced form of the command (e.g. list at the phonebooke command group selection). EXAMPLE:
=>phonebook autolist 8.35 8.36 =>phonebook [phonebook]=>autolist 8.35 8.36 [firewall]=>
Instead of entering a completely builtup command with all its parameters, you can also enter just the command itself, without its parameters. After this you are prompted to complete the command with the required and the optional parameters. For the optional parameters you can simply press enter without giving a value. The example below is the equivalent of `phonebook add name=Test addr=8*33 type=pptp`. To break of such incomplete command press Ctrl+G". EXAMPLE:

RELATED COMMANDS: bridge macdelete bridge maclist
Delete a MAC address entry. Show current filtering database.

37 / 198

bridge macdelete
Remove a MAC address from the filtering database. SYNTAX:
bridge macdelete hwaddr hwaddr = <hardwareaddress> The MAC address of the entry to delete. REQUIRED
=>bridge maclist 00:90:d0:01:02:03 static, OBC ff:ff:ff:ff:ff:ff static, OBC 01:80:c2:00:00:00 static, OBC 01:80:c2:00:00:01 static, OBC. 01:80:c2:00:00:10 static, OBC 00:80:9f:01:23:45 permanent, OBC 00:01:42:5f:7d:81 dynamic, eth0, 00:50:8b:31:cc:aa dynamic, eth0, 08:00:20:c1:9a:12 dynamic, eth0,. =>bridge macdelete hwaddr=00:80:9f:01:23:45 =>bridge maclist 00:90:d0:01:02:03 static, OBC ff:ff:ff:ff:ff:ff static, OBC 01:80:c2:00:00:00 static, OBC 01:80:c2:00:00:01 static, OBC. 01:80:c2:00:00:10 static, OBC 00:01:42:5f:7d:81 dynamic, eth0, 00:50:8b:31:cc:aa dynamic, eth0, 08:00:20:c1:9a:12 dynamic, eth0, 00:08:c7:c3:5f:fc dynamic, eth0,. =>
597 seconds 513 seconds 600 seconds

600 215

seconds seconds seconds seconds
RELATED COMMANDS: bridge macadd bridge maclist
Add a static MAC address entry. Show current filtering database.

38 / 198

bridge maclist
Show current MAC address filtering database. SYNTAX:
=>bridge maclist 00:90:d0:01:02:03 ff:ff:ff:ff:ff:ff 01:80:c2:00:00:00 01:80:c2:00:00:01. 01:80:c2:00:00:10 00:80:9f:24:ab:cf 00:01:42:5f:7d:81 00:50:8b:31:cc:aa 08:00:20:c1:9a:12 00:08:c7:c3:5f:fc 08:00:20:a8:f4:34 08:00:20:83:b7:26 00:10:83:1b:13:18. => static, static, static, static, static, static, dynamic, dynamic, dynamic, dynamic, dynamic, dynamic, dynamic, OBC OBC OBC OBC OBC OBC eth0, eth0, eth0, eth0, eth0, eth0, eth0,
seconds seconds seconds seconds seconds seconds seconds
RELATED COMMANDS: bridge macadd bridge macdelete
Add a static MAC address entry. Delete a MAC address entry.

39 / 198

bridge portadd
Create a bridge interface. SYNTAX:
bridge portadd dest = <vp*vc|name> [proto = {vcmux|llc}] [vc_mux_fcs = {off|on}] The destination address for the new interface. Typically a phonebook entry. REQUIRED

dest [encaps]

The type of encapsulation to be used for this bridge interface. Choose OPTIONAL between: G llc/snap G vcmux Whether or not to include the Ethernet FCS in the packet header on the WAN side. Choose between: G off G on OPTIONAL

[vc_mux_fcs]

eth0 state: forwarding RX bytes: 156344216 frames: 5899238 TX bytes: 75689 frames: 425 dropframes: 5558017 =>bridge portadd dest=Br1 proto=vc-mux vc_mux_fcs=on =>bridge portlist 0 OBC state: forwarding RX bytes: 75783 frames: 572 TX bytes: 82768372 frames: 341221 dropframes: eth0 state: forwarding RX bytes: 156344216 frames: 5899238 TX bytes: 75689 frames: 425 dropframes: Br1 vpi: 8 fcs: on RX bytes: 0 TX bytes: 0

52 / 198

cip pvclist
Show current PVC ARP entries. SYNTAX:
=>cip pvclist vpi = 8 vci CIPPVC1 encaps = llc => = 80 dest_ip = 172.16.1.2 mtu = 546
EXAMPLE INPUT/OUTPUT IN A NETWORKED ENVIRONMENT:
=>cip iflist cip0 addr = 200.200.200.138 mask = 255.255.255.0 hwaddr = A0:*.03 inarp_reqs_in = 0 inarp_repl_in = 75 inarp_inv_in = 0 inarp_reqs_out = 0 inarp_repl_out = 75 inarp_inv_out= 0 =>cip pvclist CIPPVC1 vpi = 6 vci = 99 dest_ip = 172.16.1.3 encaps = llc mtu = 9180 CIPPVC2 => vpi = 8 vci = 50 dest_ip = 200.200.200.14 encaps = llc mtu = 9180
RELATED COMMANDS: cip pvcdelete cip pvcadd
Delete a PVC ARP entry. Create a PVC ARP entry.

53 / 198

cip save
Save current CIP configuration. SYNTAX:
RELATED COMMANDS: cip flush cip load
Flush complete CIP configuration. Load saved or default CIP configuration.

54 / 198

5 Config Commands
config config config config config config (to access the Config level) erase flush load reset save

55 / 198

config erase
Physically remove all saved configurations. SYNTAX:
RELATED COMMANDS: config flush config load config reset config save
Flush complete runtime configuration. Load complete saved or default configuration. Flush current and optionally restore default configuration. Save complete runtime configuration.

56 / 198

config flush
Flush complete current configuration without affecting saved configurations. This combines all flush commands: atmf flush, bridge flush, cip flush, config flush, dhcp flush, dns flush, nat flush, phonebook flush, ppp flush, pptp flush, system flush and optionally ip flush. SYNTAX:
config flush [keep_ip] [keep_ip = <{no|yes}>] Keep current IP configuration (yes) or not (no). Not keeping the IP settings could cause lost IP connectivity in the LAN. By default IP settings are preserved. OPTIONAL
RELATED COMMANDS: config erase config load config reset config save
Physically remove all saved configurations. Load complete saved or default configuration. Flush current and optionally restore default configuration. Save current runtime configuration.

Second DHCP server seen

RELATED COMMANDS: dhcp clrstats
Clear DHCP server statistics.

77 / 198

dhcp status
Show current DHCP server configuration. SYNTAX:
=>dhcp status DHCP Server Status: Client Current configuration: Address Range: 10.0.0.1. 10.255.255.254 Netmask: 255.0.0.0 Lease time: 7200 seconds Gateway (default router): 10.0.0.1 (auto) DNS server: 10.0.0.1 (auto) Domain name: office.lan Policies: Verify first: no Trust client: yes Spoofing: no Start as client: yes Spoofing parameters: Failure timeout (!DoD): 4 sec Failure lease time (!DoD): 60 sec Temp. lease time (DoD): 10 sec Startup client parameters: Timeout: 20 sec Tracing: off Memory usage: Leases: total: 36, in use: 7 free: 80 % =>
RELATED COMMANDS: dhcp stop dhcp start dhcp policy dhcp spoof
Stop DHCP server. Start DHCP server. Set DHCP server policy. Set spoofing parameters.

78 / 198

dhcp stop
Stop SpeedTouchtHome/Pro DHCP server. SYNTAX:
=>dhcp status DHCP Server Status: Running Current configuration:.. =>dhcp stop =>dhcp status DHCP Server Status: Stopped Current configuration:.. =>
RELATED COMMANDS: dhcp start dhcp status
Start DHCP server. Show current DHCP server configuration.

79 / 198

dhcp troff
Disable verbose console logging. No debug traces are generated anymore. SYNTAX:
=>dhcp status DHCP Server Status: Current configuration:.. Tracing: on.. =>dhcp troff =>dhcp status DHCP Server Status: Current configuration:.. Tracing: off.. => Running

Running

RELATED COMMANDS: dhcp status dhcp tron
Show current DHCP server configuration. Enable verbose console logging.

80 / 198

dhcp tron
Enable verbose console logging. Debug traces are generated. SYNTAX:
=>dhcp status DHCP Server Status: Current configuration:.. Tracing: off.. =>dhcp tron =>dhcp status DHCP Server Status: Current configuration:.. Tracing: on.. => Running
RELATED COMMANDS: dhcp status dhcp troff
Show current DHCP server configuration Disable verbose console logging.

81 / 198

82 / 198

7 DNS Commands

dns dns dns dns dns dns dns dns dns dns dns dns dns dns dns dns dns dns dns dns dns dns (to access the DNS level) add clear clrstats delete domain flush fwdadd fwddelete fwdlist fwdtable list load nslookup save start stats status stop toutfwd troff tron

83 / 198

dns add
Add a static DNS entry for IP hosts who do not reveal their hostname in the DHCP request, or even worse, not support DHCP. SYNTAX:
dns add hostname [addr] hostname = <string> [addr = <ipaddress>] The name of the IP host (without the (sub)domain name). The IP address of the host (without mask). In case this parameter is not specified the hostname applies to the SpeedTouchtHome/Pro itself. REQUIRED OPTIONAL

addr [netmask] intf [pointopoint]] [broadcastip] [addrtrans] [addroute] [type]

106 / 198

=>ip aplist 1 eth0 Type:EthernetHWaddr 00:80:9f:24:ab:cf BRHWaddr ff:ff:ff:ff:ff:ff inet addr: 10.10.10.147 Bcast: 10.10.10.255 Mask: 255.0.0.0 UP RUNNING pat MTU:1500 ReasmMAX:65535 Group:2 IPRX bytes:19791886 unicastpkts:11341 brcastpkts:290555 IPTX bytes:839550 unicastpkts:11477 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:loop Type:0 inet addr:127.0.0.1 Bcast:127.255.255.255 Mask:255.0.0.0 UP RUNNING MTU:1500 ReasmMAX:65535 Group:1 IPRX bytes:116 unicastpkts:0 brcastpkts:2 IPTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 =>ip apadd addr=10.0.0.2 netmask=255.255.255.0 intf=eth0 addrtrans=pat addroute=yes =>ip aplist Type:EthernetHWaddr 00:80:9f:24:ab:cf BRHWaddr ff:ff:ff:ff:ff:ff 2 eth0 inet addr: 10.0.0.2 Bcast: 10.0.0.255 Mask: 255.255.255.0 UP RUNNING pat MTU:1500 ReasmMAX:65535 Group:2 IPRX bytes:0 unicastpkts:0 brcastpkts:0 IPTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:eth0 Type:EthernetHWaddr 00:80:9f:24:ab:cf BRHWaddr ff:ff:ff:ff:ff:ff inet addr: 10.10.10.147 Bcast: 10.10.10.255 Mask: 255.0.0.0 UP RUNNING pat MTU:1500 ReasmMAX:65535 Group:2 IPRX bytes:19810763 unicastpkts:11515 brcastpkts:290669 IPTX bytes:853114 unicastpkts:11662 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:loop Type:0 inet addr:127.0.0.1 Bcast:127.255.255.255 Mask:255.0.0.0 UP RUNNING MTU:1500 ReasmMAX:65535 Group:1 IPRX bytes:116 unicastpkts:0 brcastpkts:2 IPTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 =>
RELATED COMMANDS: ip apdelete ip aplist
Remove an IP address from an interface. Show current IP addresses.

107 / 198

ip apdelete
Remove an IP address from an interface. SYNTAX:

ip apdelete addr addr = <ipaddress> The IP address to delete. REQUIRED
=>ip aplist 2 eth0 Type:EthernetHWaddr 00:80:9f:24:ab:cf BRHWaddr ff:ff:ff:ff:ff:ff inet addr: 10.0.0.2 Bcast: 10.0.0.255 Mask: 255.255.255.0 UP RUNNING pat MTU:1500 ReasmMAX:65535 Group:2 IPRX bytes:0 unicastpkts:0 brcastpkts:0 IPTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:eth0 Type:EthernetHWaddr 00:80:9f:24:ab:cf BRHWaddr ff:ff:ff:ff:ff:ff inet addr: 10.10.10.147 Bcast: 10.10.10.255 Mask: 255.0.0.0 UP RUNNING pat MTU:1500 ReasmMAX:65535 Group:2 IPRX bytes:19791886 unicastpkts:11341 brcastpkts:290555 IPTX bytes:839550 unicastpkts:11477 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:loop Type:0 inet addr:127.0.0.1 Bcast:127.255.255.255 Mask:255.0.0.0 UP RUNNING MTU:1500 ReasmMAX:65535 Group:1 IPRX bytes:116 unicastpkts:0 brcastpkts:2 IPTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 =>ip apdelete addr=10.0.0.2 =>ip aplist 1 eth0 Type:EthernetHWaddr 00:80:9f:24:ab:cf BRHWaddr ff:ff:ff:ff:ff:ff inet addr: 10.10.10.147 Bcast: 10.10.10.255 Mask: 255.0.0.0 UP RUNNING pat MTU:1500 ReasmMAX:65535 Group:2 IPRX bytes:19791886 unicastpkts:11341 brcastpkts:290555 IPTX bytes:839550 unicastpkts:11477 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:loop Type:0 inet addr:127.0.0.1 Bcast:127.255.255.255 Mask:255.0.0.0 UP RUNNING MTU:1500 ReasmMAX:65535 Group:1 IPRX bytes:116 unicastpkts:0 brcastpkts:2 IPTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 =>
RELATED COMMANDS: ip apadd ip aplist
Add an IP address to an interface. Show current IP addresses.

108 / 198

ip aplist
Show a list of all configured IP addresses. SYNTAX:
=>ip aplist 2 eth0 Type:EthernetHWaddr 00:80:9f:24:ab:cf BRHWaddr ff:ff:ff:ff:ff:ff inet addr: 10.0.0.2 Bcast: 10.0.0.255 Mask: 255.255.255.0 UP RUNNING pat MTU:1500 ReasmMAX:65535 Group:2 IPRX bytes:0 unicastpkts:0 brcastpkts:0 IPTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:eth0 Type:EthernetHWaddr 00:80:9f:24:ab:cf BRHWaddr ff:ff:ff:ff:ff:ff inet addr: 10.10.10.147 Bcast: 10.10.10.255 Mask: 255.0.0.0 UP RUNNING pat MTU:1500 ReasmMAX:65535 Group:2 IPRX bytes:19791886 unicastpkts:11341 brcastpkts:290555 IPTX bytes:839550 unicastpkts:11477 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:loop Type:0 inet addr:127.0.0.1 Bcast:127.255.255.255 Mask:255.0.0.0 UP RUNNING MTU:1500 ReasmMAX:65535 Group:1 IPRX bytes:116 unicastpkts:0 brcastpkts:2 IPTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 HWRX bytes:0 unicastpkts:0 brcastpkts:0 HWTX bytes:0 unicastpkts:0 brcastpkts:0 droppkts:0 =>

115 / 198

RELATED COMMANDS: ip load ip save
Load saved or default IP configuration. Save current IP configuration.

116 / 198

ip ifconfig
Configure interface parameters. SYNTAX:
ip ifconfig intf = <interface name> [mtu = <number{293-20000}>] [status = <{down|up}>] [hwaddr = <hwaddress>] [group = <number>] The IP interface name. A number between 293 and 20000. Represents the maximum transmission unit, i.e. the maximum packet size (including IP header) to use on this interface. The default value depends on the connection and packet service for which the interface was created. The administrative status of the interface. Choose between: G down G up The hardware address (e.g. the Ethernet MAC address) of this interface. The group this interface belongs to. For internal use only. REQUIRED OPTIONAL

intf [mtu]

[status]

[hwaddr] [group]

=>ip iflist Interface GRP MTU RX 0 loop ethf 5 cip=>ip ifconfig intf=eth0 mtu=1500 =>ip iflist Interface GRP MTU RX 0 loop ethf 5 cip=> TX 0 TXDROP STATUS UP UP UP HWADDR 00:80:9f:24:ab:c

TXDROP 0 0

STATUS UP UP UP

HWADDR 00:80:9f:24:ab:c

RELATED COMMANDS: ip config
Show/set global IP stack configuration options.

117 / 198

ip iflist
Show all current interfaces. SYNTAX:
=>ip iflist Interface 0 loop 1 eth0 f 5 cip0 => GRP 0 MTU 9180 RX 0 TX 0 TXDROP STATUS UP UP UP HWADDR 00:80:9f:24:ab:c

118 / 198

ip load
Load saved (or default) IP configuration. Execute ip flush prior to ip load. SYNTAX:
ip load ip load ip load saved ip load defaults [{saved|defaults}] Load saved IP configuration. Load saved IP configuration. Load default IP configuration.
RELATED COMMANDS: ip flush ip save
Flush complete IP configuration. Save current IP configuration.

119 / 198

ip ping
Send ICMP ECHO_REQUEST packets. SYNTAX:
ip ping addr = <ip-address> [count = <number{1-1000000}>] [size = <number{1-20000}>] [interval = <number{100-1000000}>] [listen = <{off|on}>] The destination IP address. A number between 1 and 1000000. Represents the number of pings to send. A number between 1 and 20000 (bytes). Represents the size of the ping packet(s). A number between 100 and 10000000 (milliseconds). Represents the intermediate interval between two sent ICMP packets. Listen for incoming ICMP packets (on) or only send ICMP packets (off). REQUIRED OPTIONAL OPTIONAL OPTIONAL OPTIONAL
addr [count] [size] [interval] [listen]
=>ip ping addr=10.0.0.148 listen=off =>ip ping addr=10.0.0.148 listen=on 9 bytes from 10.0.0.148: Echo Request =>ip ping addr=10.0.0.148 count=15 listen=on 9 bytes from 10.0.0.148: Echo Request 9 bytes from 10.0.0.148: Echo Request 9 bytes from 10.0.0.148: Echo Request 9 bytes from 10.0.0.148: Echo Request 9 bytes from 10.0.0.148: Echo Request 9 bytes from 10.0.0.148: Echo Request 9 bytes from 10.0.0.148: Echo Request 9 bytes from 10.0.0.148: Echo Request 9 bytes from 10.0.0.148: Echo Request 9 bytes from 10.0.0.148: Echo Request 9 bytes from 10.0.0.148: Echo Request 9 bytes from 10.0.0.148: Echo Request 9 bytes from 10.0.0.148: Echo Request 9 bytes from 10.0.0.148: Echo Request 9 bytes from 10.0.0.148: Echo Request =>

dst [dstmsk] [src] [srcmsk] [gateway] [intf]
Only for special interface routes : the outgoing IP interface name. The OPTIONAL parameters `gateway` and `intf` are mutually exclusive.
=>ip rtlist Destination Source Gateway Intf Mtrc 10.0.0.0/24 10.0.0.0/24 10.0.0.140 eth10.10.0.0/24 10.0.0.0/24 10.0.0.140 eth10.0.0.140/32 0.0.0.0/0 10.0.0.140 eth127.0.0.1/32 0.0.0.0/0 127.0.0.1 loop 0 =>ip rtdelete dst=10.10.0.0/24 src=10.0.0.0/24 gateway=10.0.0.140 =>ip rtlist Destination Source Gateway Intf Mtrc 10.0.0.0/24 10.0.0.0/24 10.0.0.140 eth10.0.0.140/32 0.0.0.0/0 10.0.0.140 eth127.0.0.1/32 0.0.0.0/0 127.0.0.1 loop 0 =>
RELATED COMMANDS: ip rtadd ip rtlist
Add a route to the routing table. Show current routing table.

122 / 198

ip rtlist
Show current SpeedTouchtHome/Pro routing table. SYNTAX:
=>ip rtlist Destination 10.0.0.0/24 172.16.0.5/32 0.0.0.140/32 127.0.0.1/32 10.0.0.0/24 172.16.0.0/24 => Source 10.0.0.0/24 0.0.0.0/0 0.0.0.0/0 0.0.0.0/0 0.0.0.0/0 0.0.0.0/0 Gateway 10.0.0.140 172.16.0.5 10.0.0.140 127.0.0.1 10.0.0.140 172.16.0.5 Intf eth0 cip1 eth0 loop eth0 cip1 Mtrc 0 1
RELATED COMMANDS: ip rtadd ip rtdelete
Add a route to the routing table. Remove a route from the routing table.

123 / 198

ip save
Save current IP configuration. SYNTAX:
RELATED COMMANDS: ip flush ip load
Flush complete IP configuration. Load saved or default IP configuration.

124 / 198

ip sendto
Send UDP packets. SYNTAX:
ip sendto addr = <ip-address> [count = <number{1-1000000}>] [size = <number{1-20000}>] [interval = <number{100-1000000}>] [listen = <{off|on}>] [srcport = <number{1-65535}>] dstport = <number{1-65535}> The destination IP address. A number between 1 and 1000000. Represents the number of UDP packets to send. A number between 1 and 20000 (bytes). Represents the size of the ping packet(s). A number between 100 and 10000000 (milliseconds). Represents the intermediate interval between two sent UDP packets. Listen for incoming UDP packets (on) or only send UDP packets (off). The UDP source port number to use. The UDP destination port number to send to. REQUIRED OPTIONAL OPTIONAL OPTIONAL OPTIONAL OPTIONAL REQUIRED
addr [count] [size] [interval] [listen] [srcport] dstport
=>ip sendto addr=10.0.0.148 listen=on srcport=19 dstport=1025 =>ip sendto addr=10.0.0.148 listen=on srcport=19 dstport=bytes from 10.0.0.148:A =>ip sendto addr=10.0.0.148 count=3 listen=on srcport=19 dstport=bytes from 10.0.0.148:A 1 bytes from 10.0.0.148:A 1 bytes from 10.0.0.148:A =>
RELATED COMMANDS: ip ping
Send ICMP ECHO_REQUEST packets.

125 / 198

9 NAT Commands
The nat command group is only applicable to the SpeedTouchtPro, NOT to the SpeedTouchtHome.

RELATED COMMANDS: nat create nat delete nat disable nat list
Create a static NAPT entry. Delete a static NAPT entry. Disable NAPT on one of the SpeedTouchtPro IP addresses. List NAPT connection database.

136 / 198

nat flush
Flush complete NAPT configuration. The flush command does not impact previously saved configurations. SYNTAX:
=>nat list Indx Prot Insideaddr:Port Outsideaddr:Port Foreignaddr:Port State Control 10.0.0.138:138 10.0.0.140:138 10.0.0.20:17 10.0.0.138:137 10.0.0.140:137 10.0.0.254:17 10.0.0.138:7938 10.0.0.140:7938 10.0.0.96:17 10.0.0.138:513 10.0.0.140:513 10.0.0.109:17 10.0.0.138:111 10.0.0.140:111 10.0.0.96:20 =>nat bindlist Application Proto Port RAUDIO(PNA) tcp 7071 FTP tcp 21 RTSP tcp 554 IRC tcp 6667 RAUDIO(PNA) tcp 7070 =>nat flush =>nat list Indx Prot Insideaddr:Port Outsideaddr:Port Foreignaddr:Port State Control =>nat bindlist => Flgs Expir 10

Flgs Expir

RELATED COMMANDS: nat load nat save
Load saved or default NAPT configuration. Save current NAPT configuration.

137 / 198

nat list
Show NAPT connection database. SYNTAX:
nat list [addr] [addr = <ipaddress>] The SpeedTouchtPro IP address for which the NAPT connection database must be shown. In case the parameter is not specified the NAPT connection database for all IP addresses is shown. OPTIONAL
=>nat list Indx Prot Insideaddr:Port Outsideaddr:Port Foreignaddr:Port State Control 10.0.0.138:80 172.16.0.5:1080 0.0.0.0:17 10.0.0.138:135 10.0.0.140:135 10.0.0.155:17 10.0.0.138:138 10.0.0.140:138 10.0.0.20:17 10.0.0.138:137 10.0.0.140:137 10.0.0.254:17 10.0.0.138:7938 10.0.0.140:7938 10.0.0.96:17 10.0.0.138:513 10.0.0.140:513 10.0.0.109:17 10.0.0.138:111 10.0.0.140:111 10.0.0.96:20 => Flgs Expir 10
RELATED COMMANDS: nat create nat delete nat disable nat enable
Create a static NAPT entry. Delete a static NAPT entry. Disable NAPT on one of the SpeedTouchtPro IP addresses. Enable NAPT on one of the SpeedTouchtPro IP addresses.

138 / 198

nat load
Load saved (or default) NAPT configuration. Execute nat flush prior to nat load. SYNTAX:
nat load nat load nat load saved nat load defaults [{saved|defaults}] Load saved NAPT configuration. Load saved NAPT configuration. Load default NAPT configuration.

system load [defaults] [defaults = <yes|no>] Load factory defaults (yes) or saved configuration (no). Not specifying this parameter loads the saved configuration OPTIONAL
=>system load defaults=no =>
RELATED COMMANDS: system flush system save
Flush complete system configuration. Save current system configuration.

184 / 198

system reboot
Reboot the SpeedTouchtHome/Pro. Because rebooting implies a flush of all nonsaved configurations it is highly recommended to save the current configuration by executing config save. To avoid unrestricted and unauthorized access to the SpeedTouchtHome/Pro it is highly recommended always to make sure that it is protected by a SpeedTouchtHome/Pro system password (by executing system setpassword) and to save it (by executing system save) prior to executing this command. SYNTAX:
=>system reboot.. (lost session connectivity due to reboot)..

185 / 198

system save
Save current system configuration, i.e. the System password. To avoid unrestricted and unauthorized access to the SpeedTouchtHome/Pro it is highly recommended always to make sure that it is protected by a SpeedTouchtHome/Pro system password (by executing system setpassword) and to save it (by executing system save) prior to executing this command. SYNTAX:

=>system save =>

RELATED COMMANDS: system load system flush
Load saved or default system configuration. Flush complete system configuration.

186 / 198

system setpassword
Set/change the current SpeedTouchtHome/Pro system password. Because rebooting implies a flush of all nonsaved configurations it is highly recommended to save the current configuration via the system save command. To avoid unrestricted and unauthorized access to the SpeedTouchtHome/Pro it is highly recommended always to make sure that it is protected by a SpeedTouchtHome/Pro system password and to change it regularly. SYNTAX:
system setpassword password password = {<string>|$_BOARD_SERIAL_NBR} the system password can be set to either: G <string> A free to choose password <string> G $_BOARD_SERIAL_NBR Equal to the SpeedTouchtHome/Pro device serial number's nine numerical digits. REQUIRED
IMPORTANT NOTE: Serial number
The code serial number is printed on the marking label found on the bottom of the SpeedTouchtHome/Pro:

Q A CP992300XXX

MODEL NUMBER:
Speed Touch Home NT Tested to Comply with FCC rules Part 15 and Part 68 FOR HOME OR OFFICE USE FCC ID: 6VUBEL35680DLN REN:<0.1 Made in: Country I

3EC 18204BC AA 01

ping, ip ping, 119 policy, dhcp policy, 71 portadd, bridge portadd, 40 portconfig, bridge portconfig, 41 portdelete, bridge portdelete, 42 portlist, bridge portlist, 43 prompt, td prompt, 189 pvcadd, cip pvcadd, 51 pvcdelete, cip pvcdelete, 52 pvclist, cip pvclist, 53

196 / 198

reboot, system reboot, 183 reset, config reset, 59 rtadd ip rtadd, 120 ppp rtadd, 160 rtdelete ip rtdelete, 121 ppp rtdelete, 162 rtlist, ip rtlist, 122
start dhcp start, 75 dns start, 98 stats dhcp stats, 76 dns stats, 99 status dhcp status, 78 dns status, 100 stop dhcp stop, 79 dns stop, 101 switch, software switch, 177
save adsl save, 24 atmf save, 32 bridge save, 44 cip save, 54 config save, 60 dhcp save, 72 dns save, 97 ip save, 123 nat save, 138 phonebook save, 148 ppp save, 163 pptp save, 172 system save, 184 sendto, ip sendto, 124 setpassive, software setpassive, 176 setpassword, system setpassword, 185 spoof, dhcp spoof, 73
toutfwd, dns toutfwd, 102 troff dhcp troff, 80 dns troff, 103 tron dhcp tron, 81 dns tron, 104

unbind, nat unbind, 139

version, software version, 178

197 / 198

198 / 198

Installation Guide for the Alcatel SPEED TOUCH HOME Modem
Speed Touch Home Installation Guide
Status Released Change Note Initial Release Short Title Guide to Speed Touch Home Modem All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel.

Alcatel

Page 2
Welcome to the Speed Touch
Welcome to the Alcatel Speed Touch Asymmetric Digital Subscriber Line (ADSL) modem. From now up, your online experience will be greatly enhanced due to the high speed Internet access that the ADSL technology delivers. Over the last five years, the Alcatel ADSL has evolved from the drawing boards to operational products. This technological breakthrough coincides with an ever increasing demand for better Internet access. This Speed Touch Home User manual will be your partner in exploiting the features of this highly advanced product. For readability, the Speed Touch Home will be referred to as the STHome in this User Manual. Prior to connecting the Speed Touch Home , read the Safety Instructions (See Appendix A and B). Speed Touch, Speed Touch Home, STHome are all trade marks of Alcatel Canada.

Page 3

Conventions
The following words mark special messages throughout this document:

WARNING

WARNING: Text written in this manner indicates that failure to follow directions could cause bodily harm or loss of life.

CAUTION

CAUTION: Text written in this manner indicates that failure to follow directions could result in damage to equipment or loss of information.
Text written in this manner indicates the following presents clarifying information, specific instructions, commentary or interesting information

Page 4

Speed Touch Tour
Your Speed Touch Home is an ADSL modem used for Internet access or remote Local Area Network (LAN) access via ADSL line. This chapter aims to familiarize you with the Speed Touch Home. The topics are: Delivery check Speed Touch Home at a Glance ADSL Exposed Front and Rear Panel Light Emitting Diode (LED) Description System Requirements

Page 5

Delivery Check
Prior to installation, inspect the Speed Touch Home for damage. Make sure the box contains all the components (See figure 1): Speed Touch Home ; Power supply adapter with 2m connecting cable; 2m Ethernet straight-through cable (RJ45/RJ45), referred to as the LAN cable in this document; 2m (RJ11/RJ11) cable, referred to as the ADSL cable; the user guide.

Figure 1

In the event of damaged or missing items, contact your service provider for further instructions.

Page 6

Speed Touch Home at a Glance

2.2.1 ADSL exposed

ADSL is a brand new technology, used in the Speed Touch Home , unlocking the potential bandwidth of the widely available public telephone network. ADSL is short for Asymmetric Digital Subscriber Line. This somewhat cryptic name is best explained in straightforward terms: Line, because ADSL uses the ordinary existing copper line, known as local loop that runs between your home or office , premises and one of the telephone companies main switching exchanges, known as a central office. Subscriber, (that you), because this is what service providers s or operators call their customers or end users. Digital, because ADSL is used to transmit digital signals, just like those that make up computer files. Asymmetric, because ADSL transmits data much faster from the network towards the end user that the other way around. It is rather like having a major highway in one direction and a onelane road in the other. Because Plain Old Telephone Service (POTS) and ADSL occupy distinct frequency spectra (See figure 2), ADSL service can coexist with conventional telephone service.
ADSL Upstream ADSL Downstream

Figure 2

POTS and ADSL Frequency Spectra

Page 7

Front and rear panel

Figure 3

Front Panel of the STHome with 5 Light Emitting Diodes (LEDs)
Link Integrity LED Push Button Line Interface

Power Switch

Power socket

Ethernet interface

Figure 4

Rear Panel of STHome

Following table explains the functions of the front LEDs:

Table 1

LED Name LAN Line TX Line RX Sync PWR/Alarm
STHome LED Status Overview
LED Color green green green green green red LED State flashing off flashing off flashing off on flashing on flashing on Explanation Data is flowing from/to the Ethernet interface No activity on the Ethernet interface ATM cells are being sent over the ADSL line No transmission activity ATM cells are being received via the ADSL line No reception activity ADSL line synchronization achieved During initialization of the ADSL line Power on, normal operation Power on, self test pending Power on, self test failed

Page 8

System Requirements
ADSL Ethernet ADSL service must be enabled on your telephone line A Personal Computer (PC) or Macintosh with an Ethernet 10Base-T PC Network Interface Card (NIC) When the Speed Touch Home is used in bridging mode, it does not put any requirements on the Operating System (OS)

Operating Systems

Page 9
Connecting the Speed Touch Home
This chapter describes how to connect your Speed Touch Home. The topics discussed are: Connecting the Ethernet interface ADSL Connectivity STHome Power Supply
Figure 6 Rear view for connecting the Speed Touch Home The following connectors, switches and cables are involved:
The 10Base-T/MDI-X Ethernet interface The ADSL line interface The power receptacle The power switch
The ADSL cable The LAN cable The Power adapter Please follow the numbers on the figures 6 and 7 to complete the connections procedure for the STHome.

Page 10

Connecting the Ethernet Interface
The Ethernet port available on the STHome is a 10Base-T Half Duplex interface of type MDI-X. Use the LAN cable, to connect the Ethernet Interface of the STHome to the Ethernet port of your PC.
Straight-through Cable (provided)
Figure 7 Ethernet connection
10Base-T Half Duplex Interfacing Make sure the 10Base-T port of your PC is configured for either Auto Negotiation or Half Duplex. Never configure the PC-NIC 10Base-T Ports for Full Duplex!
Power on the STHome and the PC. The Link Integrity LEDs on both PC port and STHome should be continuously green. This indicates that the link is correct.

Page 11

Connecting the ADSL Interface
Firstly, the distributed filters (included with your starter kit), must be installed in order to prevent the ADSL channel from disturbing the phone channel and vice versa. Use one filter on each in-service telephone jack, in your home or business, sharing the same telephone line as the line where the ADSL service is delivered. This includes, but is not limited to: telephone sets, base station of hands free telephones, fax machines, modems, answering machines, etc Note: do not put a filter on the ADSL cable connecting your modem to the wall jack. Second, proceed as follows to establish the ADSL connection: Plug the ADSL cable in the Line port Plug the other end into the telephone line jack in the wall.
Connecting the Power Supply
The STHome is delivered with a modular external power adapter. Proceed as follows to connect the power supply adapter: Plug the power adapter coaxial jack into the receptacle s Plug the power supply adapter into the wall power outlet. Turn on the STHome with the power switch Check the visual indicators on top of the STHome (See section 2.2.2). The visual indicator marked PWR/Alarm initially flashes red, indicating that the STHome is performing a self test. If the self test was successful, the PWR/Alarm indicator shows continuous green. At this point, the STHome is ready for ADSL connectivity

Page 12

Troubleshooting
Problem Speed Touch Home modem does not work (no visual indicator on front lights up) Ethernet connection does not work Solution Make sure the STHome is plugged in. Make sure the STHome is turned on. Make sure the cable is securely connected to the 10BASE-T connector and that you are using the correct cable type for your Ethernet equipment. Make sure the STHome modem is installed as described in the instruction provider in this user guide. Make sure the STHome modem has adequate ventilation. Place the modem on an even, hard surface. Do not stack books or paper on the modem. Make sure you have installed a filter on every telephone, modem, fax machine, etc that shares the same telephone line as the one where the ADSL signal is provided. Power/Sync LED is constantly green, but no traffic passes through Power/Sync LED remains constantly red Restart the STHome modem
Poor Speed Touch Home modem performance.
Restart the STHome modem. Make sure that you did not put a filter on the ADSL cable between the modem and the telephone jack.
If the troubleshooting tips listed above have not resolved the problem, contact your service provider for assistance.

Page 13

Abbreviations
AAL ADSL ATM CLI DHCP DNS DTE HDLC HTML HTTP IP ISDN ISP LAN LED LLC MAC MDI MDI X MUX NIC NLPID OS PC POTS PPP PPTP RAS RFC ROW SNAP TCP URL VC VCI VPI VPN WAN WWW ATM Adoption Layer Asymmetric Digital Subscriber Line Asynchronous Transfer Mode Command Line Interface Dynamic Host Configuration Protocol Domain Name System Data Terminal Equipment High level Data Link Control Hypertext Markup Language Hypertext Transfer Protocol Internet Protocol Integrated Service Digital Network Internet Service Provider Local Area Network Light Emitting Diode Logical Link Control Medium Access Control Medium Dependent Interface Medium Dependent Interface Crossed Multiplexing Network Interface Card Network Link Protocol Identifier Operating System Personal Computer Plain Old Telephone Service Point-to-Point Protocol Point-to-Point Tunneling Protocol Remote Access Services Request For Comments Rest of the World Sub-Network Access Protocol Transmission Control Protocol Uniform Resource Locator Virtual Channel Virtual Channel Identifier Virtual Path Identifier Virtual Private Network Wide Area Network World Wide Web

Page 14

Appendix A

Safety

This appendix provides basic Safety Information on your Speed Touch Home. Prior to using the STHome , read this Appendix carefully.
Safety Instructions Read and understand all instructions. Follow all warnings and instructions marked on the product. Climatic conditions The STHome equipment is intended for : In-house stationary desktop use; the maximum ambient temperature may not exceed 40C. It must not be mounted in a location exposed to direct or excessive solar and/or heat radiation. It must not be exposed to heat trap conditions and must not be subjected to water or condensation. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Water and moisture Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool.

Page 15

Power supply adapter The Speed Touch Home comes with a portable power supply adapter. Power sources The powering of this product must adhere to the power specifications indicated on the marking labels. If you are unsure of the type of power supply to your home, consult your product dealer or local power company. The main socket outlet must be close to the equipment and easily accessible. Power cord protection Do not allow anything to rest on the power cord. Do not locate this product where the cord will be subject to persons walking on it. Overloads Do not overload wall outlets and extension cords as this increases the risk of fire or electric shock. Servicing To reduce the risk of electric shock, do not disassemble this product. None of its internal parts are user-replaceable; therefore, there is no reason to access the interior. Opening or removing covers may expose you to dangerous voltages. Incorrect reassembly could cause electric shock if the appliance is subsequently used. If service or repair work is required, take it to a qualified service dealer.

Page 16

Damage requiring service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power supply cord or plug is damaged or frayed. If liquid has been spilled into the product. If the product has been exposed to rain or water. If the product does not operate normally. If the product has been dropped or damaged in any way. If the product exhibits a distinct change in performance. Modem/Telephone use Distributed filters must be installed on each telephone, modem, fax machine using the same telephone line as the ADSL signal for optimal performance.

KEEP THESE INSTRUCTIONS!

Page 17

Safety Standards

The Speed Touch Home complies with the following safety standards: EN 60950, 2nd ed. (1992), including amendments 1 (1993), 2 (1993), 3 (1995) and 4 (1997). IEC 60950, 2nd ed. (1991), including amendments 1 (1992), 2 (1993), 3 (1995) et 4 (1996) The external interfaces on the rear of the panel are classified as follows: Line: TNV circuit subjected to overvoltages (TNV-3). 10Base-T / MDI-X: SELV circuit. DC (Power socket): connection to coaxial plug from the power supply adapter.

Page 18

Appendix BAgency Regulatory Notices
B.1 Canadian DOC Class B Notice
Notification of Canadian RF Interference Statements This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communication.

US FCC Class B Notice

Federal Communications Commission (FCC) Statements This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to guarantee this device doesn harmfully interfere with, or harmfully be interfered by other devices. t Radio Frequency Interference Statement Note: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications. The limits are designed to provide reasonable protection against such interference in a residential situation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one of more of the following measures: Reorient or relocate the receiving antenna of the affected radio or television; Increase the separation between the equipment and the affected receiver; Connect the equipment and the affected receiver to power outlets on separate circuits; Consult the dealer or an experienced ratio/TV technician for help.

Modifications Changes or modifications not expressly approved by Alcatel could invalidate the user s authority to operate this equipment.
European Community Declaration of Conformity
Alcatel declare, sole responsibility that this product, to which this declaration relates, is in conformity with the following standard(s) and other common practices: EN 50081-1: 1992, Electromagnetic Compatibility Generic emissions standards Part 1: Residential, commercial and light industry following the provisions of The Electromagnetic Compatibility Directive, 89/336/EEC. EN 50082-1: 1992, Electromagnetic Compatibility Generic emissions standards Part 1: Residential, commercial and light industry following the provisions of The Electromagnetic Compatibility Directive, 89/336/EEC. EN 60950: 1992,Safety of Information Technology Equipment, including Electrical Business Equipment.

Page 19