Reviews & Opinions
Independent and trusted. Read before buy Alpine CDA-9811R!

Alpine CDA-9811R

Manual

Preview of first few manual pages (at low quality). Check before download. Click to enlarge.
Manual - 1 page  Manual - 2 page  Manual - 3 page 

Download (English)
Alpine CDA-9811R Car Audio, size: 1.1 MB
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Alpine CDA-9811RAbout Alpine CDA-9811R
Here you can find all about Alpine CDA-9811R like manual and other informations. For example: review.

Alpine CDA-9811R manual (user guide) is ready to download for free.

On the bottom of page users can write a review. If you own a Alpine CDA-9811R please write about it to help other people.

 

[ Report abuse or wrong photo | Share your Alpine CDA-9811R photo ]

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

No opinions have been provided. Be the first and add a new opinion/review.

 

Documents

doc0

When traffic information stations cannot be received:
In the tuner mode: When the TP signal can no longer be received for over 1 minute, the underlined portion of the T.INFO indicator (only the upper lined portion of the T.INFO indicator for CDA-9813R/CDA-9812RX) blinks. In the CD mode: When the TP signal can no longer be received, the traffic information station of another frequency will be selected automatically. The receiver is equipped with the EON (Enhanced Other Networks) function in order to keep track of additional alternate frequencies to the AF list. The underlined portion of the EON indicator (only the upper lined portion of the EON indicator for CDA-9813R/CDA-9812RX) lights up while an RDS EON station is being received. If the station being received does not broadcast the traffic information, the receiver automatically tunes in the related station that broadcasts the traffic information when it occurs.
Press 3/PTY within 5 seconds after selecting the programme type to start searching for a station in the selected programme type.
The chosen programme type display blinks during searching and lights when a station is found. If no PTY station is found, NO PTY will be displayed for 5 seconds.
Press F/SETUP to activate the normal mode. The FUNC indicator (only the underlined portion of the FUNC indicator for CDA-9811R) goes out.
Operate the unit while the FUNC indicator (only the underlined portion of the FUNC indicator for CDA-9811R) lights up. If no operation is performed within 5 seconds, the FUNC indicator (only the underlined portion of the FUNC indicator for CDA9811R) goes out.
Press T.INFO to deactivate the Traffic Information mode.
The underlined portion of the T.INFO indicator (only the upper lined portion of the T.INFO indicator for CDA9813R/CDA-9812RX) goes out.
Priority PTY (Programme Type)
This function allows presetting of a programme type such as music category, news, etc. You can listen to a programme in the preset programme type as the unit automatically gives priority to the preset programme type when it begins broadcasting, and interrupts the programme you are currently listening. This feature is functional when your unit is set to a mode other than the LW and MW.

Displaying Radio Text

Text messages from a radio station can be displayed.
Press TITLE while receiving FM in the radio mode to select the Radio Text display.

Terminology

Bit rate This is the sound compression rate specified for encoding. The higher the bit rate, the higher the sound quality, but also the larger the files. Sampling rate This value shows how many times per second the data is sampled (recorded). For example, music CDs use a sampling rate of 44.1 kHz, so the sound is sampled (recorded) 44,100 times per second. The higher the sampling rate, the higher the sound quality, but also the larger the volume of data. Encoding Converting music CDs, WAVE (AIFF) files, and other sound files into the specified audio compression format. Tag Song information such as track titles, artist names, album names, etc., written into MP3/WMA files. MP3: ID3 tag WMA: WMA tag

Formats supported

This device supports CD-ROM XA, Mixed Mode CD, Enhanced CD (CD-Extra) and Multi-Session. This device cannot correctly play back discs recorded with Track At Once or packet writing.

Order of tracks

The unit plays the files in the order that the writing software writes them. Therefore, the playing order may not be the same as the order you input. The playback order of the folders and files is as follows. However, the folder and file playback order differs from the folder no. and file no. indicated on the display.

Folder

MP3/WMA File
SOURCE/ POWER BAND/ Rotary encoder TEL. Preset buttons (1 through 6)
Setting the Bass Control (CDA-9812RX/CDA9811R only)
You can change the bass frequency emphasis to create your own tonal preference.
Press CENTER f to select the Bass (bass centre frequency) Control mode.
BASS TREBLE normal mode BASS
g MX f T.CORR/ X-OVER EQ (CDA-9815RB/CDA-9813R) CENTER f (CDA-9812RX/CDA-9811R)
Setting the bass centre frequency: Press g or f to select the desired bass centre frequency.
60Hz 70Hz 80Hz 90Hz 100Hz 130Hz 150Hz 200Hz 60Hz
The displayed bass frequency is emphasized
Adjusting Balance (Between Left and Right)/ Fader (Between Front and Rear)/Defeat
Setting the bass band width (Q-Factor): Press BAND/TEL. to select the desired bass band width. B. Width1 B. Width2 B. Width3 B. Width4 (Narrow).. (Wide)
Changes the boosted bass band width to wide or narrow. A wide setting will boost a wide range of frequencies above and below the centre frequency. A narrower setting will boost only frequencies near the centre frequency.
Press Rotary encoder repeatedly to choose the desired mode.
Each press changes the modes as follows:
SUBWOOFER*1 BALANCE FADER DEFEAT VOLUME SUBWOOFER*1 Subwoofer : 0 ~ +15 Balance : L15 ~ R15 Fader : R15 ~ F15 Defeat : ON/OFF Volume : 0 ~ 35

3 way mode Cut-off frequency (1/3 octave steps) HPF Low range speaker LPF 20 Hz 200 Hz HPF
Adjusting and Storing the Crossover Settings (CDA-9815RB/CDA-9813R only)
Before performing the following procedures, refer to About the Crossover (Page 19).
FLAT, 6, 12, 18, 24 dB/ oct

2 WAY System

Mid range speaker

20 Hz 20 kHz

FLAT, 6, FLAT, 6, 12, 18, 12, 18, 24 dB/ 24 dB/ oct oct 6, 12, 18, 24 dB/oct
Press BAND/TEL. to select desired parameter.
LOW (Subwoofer) REAR FRONT LOW (Subwoofer)
Press g or f to select desired cut-off frequency point (crossover point).
Adjustable frequency bands: 20Hz to 200Hz (in 1/3 octave steps)

High range speaker

1 kHz 20 kHz
Low range Mid range High range
Press SOURCE/POWER to select desired slope.
Adjustable slope: 0 (FLAT (OFF)), 1 (-6dB/oct), 2 (-12dB/ oct), 3 (-18dB/oct), 4 (-24dB/oct).
(Different from actual display) Level adjusting (0 to - 12 dB) Output frequency range
Turn the Rotary encoder to select the desired output level.
Adjustable output level: -12 to 0 dB.
To store the adjusted contents 1) Press and hold any one of the preset buttons (1 through 6) for at least 2 seconds into which you wish to store the adjusted contents.
Slope FLAT Slope adjusting
For setting another channel, repeat the steps 2 to 5. After setting, press T.CORR/X-OVER to return to normal mode.
20 Hz HPF cut-off frequency
(Different from actual display) LPF cut-off frequency
Crossover mode is automatically cancelled if no operation is performed within 15 seconds.

3 WAY System

HPF (high pass filter): Cuts the lower frequencies and allows the higher frequencies to pass. LPF (low pass filter): Cuts the higher frequencies and allows the lower frequencies to pass. Slope: The level change (in dB) for a frequency change of one octave. The higher the slope value, the steeper the slope becomes. Adjust the slope to FLAT to bypass the HP or LP filters. Do not use a tweeter without the HPF on or set to a low frequency, as it may cause damage to the speaker due to the low frequency content. You cannot adjust the crossover frequency higher than the HPF or lower than the LPF. Adjustment should be made according to the recommended crossover frequency of the connected speakers. Determine the recommended crossover frequency of the speakers. Adjusting to a frequency range outside that recommended may cause damage to the speakers. For the recommended crossover frequencies of Alpine speakers, refer to the respective Owner's Manual. We are not responsible for damage or malfunction of speakers caused by using the crossover outside the recommended value.
LOW MID-L MID-H HIGH (HI) LOW
Adjustable frequency bands:
LOW MID-L MID-H HIGH : 20Hz to 200Hz (in 1/3 octave steps) : 20Hz to 200Hz (in 1/3 octave steps) : 20Hz to 20kHz (in 1/3 octave steps) : 1kHz to 20kHz (in 1/3 octave steps)

Any manual time correction adjustments will also affect corrections made in Bass Focus. Bass Focus mode is automatically cancelled if no operation is performed within 15 seconds.
Example setting for steps 2 and 3
(1) Press BAND/TEL. to select the front (left and right) speakers. Then turn the Rotary encoder to select 1.5 ms (Delay no. 15 in the table). The time difference is 1.5 ms for both front (left and right speakers.
Adjusting and Storing the Time Correction (Storing available on CDA-9815RB/CDA-9813R only)
Before performing the following procedures, refer to About Time Correction (page 21).

Setting the MX Mode

MX (Media Xpander) makes vocals or instruments sound distinct regardless of the music source. The radio, CD, and MP3, will be able to reproduce the music clearly even in cars with a lot of road noise.
Press T.CORR/X-OVER to make time corrections.
Each press changes the mode as follows:
Bass Focus mode Time Correction mode normal mode Bass Focus mode
Press MX to select MX ON. Press SOURCE/POWER to select the source to which you want to apply MX (Media Xpander). Press and hold MX for at least 2 seconds to activate the level setting mode. Turn the Rotary encoder to select your preferred level or OFF.
Press BAND/TEL. to select a speaker to be adjusted.
CDA-9815RB/CDA-9813R FLFRRLRRSLSRFL CDA-9812RX/CDA-9811R FLFRRLRRFL
FM (MX level 1 to 3): The medium to high frequencies become clearer, and produces well balanced sound at all frequencies. CD (MX level 1 to 3): CD mode processes a large quantity of data. This data processing power takes advantage of CD quality sound sources. MP3/WMA/DAB (MX level 1 to 3): This corrects information that was lost at the time of compression. This reproduces a well-balanced sound close to the original. DVD (Video CD) (MOVIE MX level 1 to 2): The dialogue portion of a video is reproduced more clearly. (MUSIC MX level 1): A DVD or Video CD contains a large quantity of data such as music clip. MX uses this data to reproduce the sound accurately. AUX (MX level 1): Choose the MX mode (MP3, MUSIC, or MOVIE) that corresponds to the media connected. If two external devices are connected, a different MX mode for each media can be selected.

For CDA-9815RB, see asterisk 1 of Displaying the Title/Text (page 24).
Press and hold -/J for at least 2 seconds.
The title in the display will blink.
Press g or f repeatedly until the title you want to erase is displayed. Press and hold -/J for at least 2 seconds to erase the title displayed. Press TITLE to cancel the title erasing mode.

Titling Discs/Stations

It is possible to title your favourite CD's or radio stations. You cannot input titles on MP3/WMA discs.
You cannot erase CD-TEXT. NO DATA is displayed for 2 seconds if the title is not input in step 2, or if the title is erased in step 4.
Press TITLE and select the Title Display.
For details, see Displaying the Title/Text (page 24). For CDA-9815RB, see asterisk 1 of Displaying the Title/Text (page 24).

Blackout Mode On and Off

When Blackout mode is turned on, the display will turn off to reduce power consumption. This additional power enhances the sound quality.
Press and hold TITLE for at least 3 seconds. The first character will blink.

CDA-9815RB only

Press BAND/TEL. to select the characters/ symbols.
Upper case Lower case Numeral/Symbol Upper case
Press and hold DISP/B.OUT (CDA-9815RB/CDA9813R/CDA-9812RX) or MUTE/B.OUT (CDA-9811R) for at least 3 seconds to activate the blackout mode.
The display will turn off. If any button on the unit is pressed during the blackout mode, the function will be displayed for 5 seconds to show the operation before returning to Blackout mode. To cancel Blackout mode, press and hold DISP/B.OUT (CDA9815RB/CDA-9813R/CDA-9812RX) or MUTE/B.OUT (CDA9811R) for at least 3 seconds.
Turn the Rotary encoder to select the desired letter/numeral/symbol available for naming. Press Rotary encoder to store the first character.
The first character will stop blinking and the display will automatically advance to the next character. When that character begins to blink, you may choose the next letter or symbol of your title.
i-Personalize Operation (CDA-9815RB/CDA9813R only)
SOURCE/ POWER -/J Rotary encoder

Data Downloading

Insert the CD-R disc containing the data. If the source is not the CD mode, press SOURCE/ POWER to change to CD mode. Press and hold -/J for at least 2 seconds.
The mode switches to the download mode to show the download confirmation screen.
Turn the Rotary encoder to select OK, then press the Rotary encoder.
Data search of the disc starts and the first file name is displayed.
Selecting NG will halt the download mode. If a file is not found by the data search, NO FILE is indicated. The NO FILE display will automatically disappear if no operation is performed for 5 seconds.

Scroll Setting

SCROLL AUTO / SCROLL MANUAL (Initial setting)

Press F/SETUP again.

The display returns to normal mode.
This CD player can scroll the disc and track names recorded on CDTEXT discs, as well as the text information of MP3/WMA files, folder names, and tags. (This function can be used for CDA-9811R if a changer compatible with CD-Text is connected.)
SCROLL AUTO : The CD text information, the text information of folder and file names, and the tags are scrolled automatically. SCROLL MANUAL : The display is scrolled only when a disc is loaded or when a track is changed, etc.

Sound Customizing

Adjusting Source Signal Levels
FM-LEVEL HIGH (Initial setting) / FM-LEVEL LOW
If the difference in volume level between the CD player and FM radio is too great, adjust the FM signal level.
The unit scrolls CD text names, folder names, file names or tag display. The disc titles input manually (page 25) cannot be scrolled.
Scroll Type Setting (CDA-9815RB only)
TYPE1 (Initial setting) / TYPE2
Connecting to an External Amplifier
PWR-IC ON (Initial setting) / PWR-IC OFF
Two types of scroll can be selected.
TYPE1: The upper line and lower line scroll alternately. TYPE2: The upper line and lower line scroll at the same time, but at different speeds, when the Scroll Setting (page 27) is set to SCROLL AUTO.
When an external amplifier is connected, sound quality can be improved by stopping the power supply of the built-in amplifier.
PWR-IC OFF : Use this mode when the front and rear preamplifier of the unit are used to drive an external amplifier connected to the speakers. In this setting, the head units internal amplifier has no output to drive speakers. Front left Front right Rear left Rear right
Switching the Character Font (CDA-9815RB only)
TYPE-1 (Initial setting) / TYPE-2
Two types of font can be selected. You can select the font type you like.

Amplifier

Adjusting Display Contrast (CDA-9815RB only)

CONTRAST

You can adjust the display contrast for better visibility. You can adjust in a range of - 6 and + 6. The initial setting at the factory is 0.
(Connecting example for CDA-9815RB)
PWR-IC ON : The speakers are driven by the built-in amplifier.

Demonstration

DEMO ON / DEMO OFF (Initial setting)

Speakers

SPEAKER RIGHT FRONT
This unit has a Demonstration feature which simulates the display functions. To quit Demo mode, set to DEMO OFF.

Front right

Playing MP3 Data
CD-DA (Initial setting) / CD-DA/MP3

SPEAKER RIGHT REAR

Rear right
This product can playback CDs containing both CD and MP3/WMA data. However, in some situations (some enhanced CDs), playback may be difficult. For these special cases, you can select playback of CD data only. When a disc contains both CD or the MP3/WMA data, playback starts from the CD data portion of the disc. MP3 can be played back for CDA-9811R if an MP3 compatible changer is connected.

If there exists a Secondary Service Component within a service, the indicator S blinks on the display. When receiving the Secondary Service Component, the indicator S remains lit.

Memorizing the Service

Memorizing the Ensemble Automatically
Select the service that you want to memorize. Press any one of the Preset buttons (1 through 6) for at least 2 seconds while the FUNC indicator (only underlined portion of the FUNC indicator for CDA-9811R) goes out. The selected service is memorized. To memorize more, repeat the above steps 1 and 2.
Press BAND/TEL. to select the band that you want to receive. Press and hold TUNE/A.ME for at least 2 seconds.
The ensemble is searched for, and six ensembles are automatically received and memorized with the preset buttons (1 through 6). When memorization has completed, the Ensemble that was memorized last is received. By selecting the mode in the Changing the Display Mode (page 31), the display shows the status of the broadcasting stations that have been received as follows: Channel No. Display: the channel numbers of received stations are displayed. Ensemble Label Display: the Ensemble Label of received station is displayed. Service Label Display: the Ensemble Label is displayed for 2 seconds and then the Service Label is displayed after receiving the broadcasting station. Component Label Display: the Ensemble Label is displayed for 2 seconds, then the Service Label is displayed for 2 seconds, and then the display is changed to the Component Label after receiving the broadcasting station. Dynamic Label Display: the Ensemble Label is displayed for 2 seconds, then the Service Label is displayed for 2 seconds, and then the display is changed to the Dynamic Label after receiving the broadcasting station. Frequency Display*2 : the frequency of received stations are displayed.
You can memorize up to 18 stations (6 stations for each band; DAB1, DAB2, DAB3). If you select a preset button that has already memorized a service, the new selection takes it over. When you are not receiving DAB, the service is not memorized. (Memorize the service when the DAB reception is good)
Receiving the Memorized Service
Press BAND/TEL. to select your desired band. Press one of the Preset buttons (1 through 6).
The selected service is received. By selecting the mode in the Changing the Display Mode (page 31), the display shows the status of the broadcasting stations that have been received as follows: Channel No. Display: the channel numbers of received stations are displayed. Ensemble Label Display: the Ensemble Label of received station is displayed. Service Label Display: the Ensemble Label is displayed for 2 seconds and then the Service Label is displayed after receiving the broadcasting station. Component Label Display: the Ensemble Label is displayed for 2 seconds, then the Service Label is displayed for 2 seconds, and then the display is changed to the Component Label after receiving the broadcasting station. Dynamic Label Display: the Ensemble Label is displayed for 2 seconds, then the Service Label is displayed for 2 seconds, and then the display is changed to the Dynamic Label after receiving the broadcasting station. Frequency Display*1 : the frequency of received stations are displayed.

Press F/SETUP to return to the normal mode.
Press F/SETUP for at least 3 seconds. Press g or f select DAB DRC (DRC). Press BAND/TEL. to select either ON or OFF. Press F/SETUP to return to the normal mode.
When a radio programme is set to ON, sound other than what you previously set may be produced depending on the broadcast. In this case, turn the programme OFF.
MobileHub Link Operation(Optional)
SOURCE/ POWER -/J BAND/ TEL. TITLE 8 SEARCH 9
An outgoing call from a portable telephone is also possible. However, you cannot perform different operations at the same time from a portable telephone and CDA-9815RB/CDA-9813R/CDA9812RX/CDA-9811R as malfunction can result. With a junction box connected outgoing, incoming, and sending history will also be recorded in the portable telephone. While telephoning, defeat is set to ON. When the call has finished, the unit returns to your previous setting. The telephone volume can be adjusted on the CDA-9815RB/CDA9813R/CDA-9812RX/CDA-9811R. The volume you set during the call is memorized, and is automatically applied again on the next call. While telephoning or receiving incoming calls, press TITLE to show the Network Operator display for 5 seconds.

Incoming Calls

g f F/SETUP Preset buttons (1 through 6)
Press :/J to receive an incoming call. Press BAND/TEL. to finish a call.
Telephone mode will end and return to the original source mode.

About MobileHub Link

Connect a separately sold junction box and a portable telephone (available from Nokia) to control the incoming and outgoing calls of the portable telephone.
Caution Even with hands-free operation, a driver can be distracted during telephone operation or receiving a call. For the sake of safety, drivers are requested to refrain from operating the telephone while driving. For the sake of safety, only incoming calls and Speed-Dial outgoing calls can be operated.
When the Automatic Calling mode is on, you can talk after 3 seconds of receiving the incoming call. The incoming call can be switched to Automatic Calling or Manual Calling. 1 Press and hold F/SETUP for at least 3 seconds. 2 Select the Telephone mode by pressing g or f. 3 Press BAND/TEL. to change to AUTO or MANUAL (MANU). 4 Press F/SETUP to return to normal mode. Press BAND/TEL. during an incoming call to disconnect it.
If a portable telephone is connected, its address book, incoming and outgoing history are downloaded to the junction box. Please refer to the instruction manual of the junction box.

Telephone Mode ON/OFF

Press and hold BAND/TEL. for at least 2 seconds to turn on the Telephone mode.
To turn off, press BAND/TEL. See relevant pages for each item.

If the selected CD Changer is not connected, the display will show NO CHGR (NO CHANGER for CDA-9815RB). To operate the selected changer, see CD/MP3/WMA (page 13). For further details about the external input (AUX) when using KCA-410C, see Setting the AUX Mode (V-Link) on page 28.

9 ! " #

9 f UP Button
Radio mode: SEEK (UP) button CD mode: Press this button to advance to the beginning of the next track.

! 9 Button

Radio mode: Pressing this button will select, in descending order, stations programmed into the radio's presets as shown below.

6 5. 1 6

CD Changer mode: DISC Select (DN) button Press this button to select a disc in descending order. MP3/WMA mode: Press the Folder Select (DN) button to select the folder.

" Mute Button

Press this button to lower the volume by 20 dB instantly. Press this button again to cancel.
# Audio Processor Button*1
Controls on Remote Control (CDA-9815RB/ CDA-9813R/CDA-9812RX only)

1 Power Button

Press this button to turn the power on/off.

2 Source Button

Press this button to select the audio source.
CDA-9815RB/CDA-9813R only Each press the button to switch the audio processor mode. For details, refer to Operating the Audio Processor as shown below. CDA-9815RB/CDA-9813R/CDA-9812RX Press the button to call the external audio processor mode when the external audio processor is connected.*2 *1 This button is used for CDA-9812RX in conjunction with an optional Ai-NET processor. *2 For the operation of external audio processor, refer to the Owner's Manual of the external audio processor you purchased.

3 -/J Button

Press this button to switch between the Play and Pause modes for CD.

4 TILT 98 Buttons

Press this button to adjust the angle of the movable display.
Operating the Audio Processor (CDA-9815RB/CDA-9813R only)

5 Band/Programme Button

Radio mode: BAND Button Press this button and the band will change. CD/Changer mode: To switch the disc mode.
Press A.PROC to select the mode.
Normal mode EQ mode (Equalizer Presets) Private mode (Recalling the Stored Equalizer Curve) Time Correction mode (Recalling the Stored Time Correction) Crossover mode (Recalling the Stored Crossover) Normal mode

6 Volume Adjustment Buttons
To increase the volume level: Press the Lbutton To decrease the volume level: Press the Kbutton
Press 8 or 9 to select the mode.
EQ mode Select from FLAT, POPS, ROCK and NEWS. Private mode/Time Correction mode/Crossover mode Select from MEMORY 1 through 6.

Button

Radio mode: Pressing this button will select, in ascending order, stations programmed into the radio's presets as shown below.

1 2. 6 1

CD Changer mode: DISC Select (UP) button Press this button to select a disc in ascending order. MP3/WMA mode: Press the Folder Select (UP) button to select the folder.

8 g DN Button

Radio mode: SEEK (DN) Button CD mode: Press this button to go back to the beginning of the current track.
Battery Replacement (CDA-9815RB/CDA9813R/CDA-9812RX only)
Applicable battery: Use two AAA sized dry batteries or equivalent.

In Case of Difficulty

If you encounter a problem, please turn the power off, then on again. If the unit is still not functioning normally, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer.
Opening the battery cover
Slide out the battery cover while firmly pressing in the direction of the arrow.
No function or display. Vehicle's ignition is off. - If connected following instructions, the unit will not operate with the vehicle's ignition off. Improper power lead connections. - Check power lead connections. Blown fuse. - Check the fuse on the battery lead of the unit; replace with the proper value if necessary. Internal micro-computer malfunctioned due to interference noise etc. - Press the RESET switch with a ballpoint pen or other pointed article.

Replacing the battery

Insert the batteries, observing the polarities as illustrated.

Closing the cover

Slide the cover as illustrated until a click is heard.
Unable to receive stations. No antenna or open connection in cable. - Make sure the antenna is properly connected; replace the antenna or cable if necessary. Unable to tune stations in the seek mode. You are in a weak signal area. - Make sure the tuner is in the DX mode. If the area you are in is a primary signal area, the antenna may not be grounded and connected properly. - Check your antenna connections; make sure the antenna is properly grounded at its mounting location. The antenna may not be the proper length. - Make sure the antenna is fully extended; if broken, replace the antenna with a new one. Broadcast is noisy. The antenna is not the proper length. - Extend the antenna fully; replace it if it is broken. The antenna is poorly grounded. - Make sure the antenna is grounded properly at its mounting location.

Controllable With Remote Control The CDA-9811R can be controlled with an optional Alpine remote control. For details, consult your Alpine dealer. Point the optional remote control transmitter at the remote control sensor.

Remote control sensor

Connectable to Remote Control Interface Box You can operate this unit from the vehicle's control unit when an Alpine Remote Control Interface Box (optional) is connected. For details, contact your Alpine dealer.
CD Player/Changer not functioning. Out of operating temperature range +50C (+120F) for CD. - Allow the vehicle's interior (or trunk) temperature to cool. CD playback sound is wavering. Moisture condensation in the CD Module. - Allow enough time for the condensation to evaporate (about 1 hour).
CD insertion not possible. A CD is already in the CD player. - Eject the CD and remove it. The CD is being improperly inserted. - Make sure the CD is being inserted following instructions in the CD Player Operation section. Unable to fast forward or backward the CD. The CD has been damaged. - Eject the CD and discard it; using a damaged CD in your unit can cause damage to the mechanism. CD playback sound skips due to vibration. Improper mounting of the unit. - Securely re-mount the unit. The disc is very dirty. - Clean the disc. The disc has scratches. - Change the disc. The pick-up lens is dirty. - Do not use a commercial available lens cleaner disc. Consult your nearest ALPINE dealer. CD playback sound skips without vibration. The disc is dirty or scratched. - Clean the disc; damaged disc should be replaced. Error displays (built-in CD player only) Mechanical error - Press c. After the error indication disappears, insert the disc again. If the above-mentioned solution does not solve the problem, consult your nearest ALPINE dealer. CD-R/CD-RW playback not possible Close session (finalization) has not been performed. - Perform finalization and attempt playback again.
Mechanism error. 1) Press the c button and eject the CD. If not ejecting, consult your Alpine dealer. 2) When the error indication remains after ejecting, press the c button again. If the error indication still does not turn off after pressing the c button for a few times, consult your Alpine dealer.

When ERROR is displayed: If that the disc cannot be ejected by pressing c, press the RESET switch (refer to page 6) and press c again. If the disc still cannot be ejected, consult your Alpine dealer.

PROTECT

(CDA-9815RB/CDA-9813R/CDA-9812RX only) A copy-protected WMA file was played back. - You can only play back non-copy-protected files.

UNSUPPORT

(CDA-9815RB/CDA-9813R/CDA-9812RX only) The disc is not written in a MP3/WMA supported format. - Use a disc written at the MP3/WMA supported format.
Indication for CD Changer

HIGH TEMP

HI TEMP

MP3/WMA

MP3 or WMA is not played back. Writing error occurred. The CD format is not compatible. - Make sure the CD has been written in a supported format. Refer to About MP3/WMA (page 15-16), then rewrite in the format supported by this device.
(CDA-9815RB) (CDA-9813R/CDA-9812RX/CDA-9811R) Protective circuit is activated due to high temperature. - The indicator will disappear when the temperature returns to within operation range.

ERROR - 01

Malfunction in the CD Changer. - Consult your Alpine dealer. Press the magazine eject button and pull out the magazine. Check the indication. Insert the magazine again. If the magazine cannot be pulled out, consult your Alpine dealer. Magazine ejection not possible. - Press the magazine eject button. If the magazine does not eject, consult your Alpine dealer.

Indication for CD Player

ERROR - 02
A disc is left inside the CD Changer. - Press the eject button to activate the eject function. When the CD Changer finishes the eject function, insert an empty CD magazine into the CD Changer to receive the disc left inside the CD Changer.

NO DISC

No CD is inserted. - Insert a CD. Although a disc is inserted, NO DISC is displayed and the unit does not start to play or eject the disc. - Remove the disc by following these steps: 1) Press the c button. The movable display will open. 2) Press the c button again for at least 3 seconds while the movable display is open.

NO MAGAZINE

(CDA-9815RB)

NO MAGZINE

(CDA-9813R/CDA-9812RX)
CHASSIS SIZE Width Height Depth

NO MAGZN

(CDA-9811R)
178 mm (7") 50 mm (2") CDA-9815RB/CDA-9813R 155 mm (6-1/8") CDA-9812RX/CDA-9811R 160 mm (6-1/4") 170 mm (6-11/16") 46 mm (1-13/16") 20 mm (25/32")
No magazine is loaded into the CD Changer. - Insert a magazine.
No indicated disc. - Choose another disc.
NOSEPIECE SIZE Width Height Depth

DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.
When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.
Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.

Precautions

Be sure to disconnect the cable from the () battery post before installing your CDA-9815RB/CDA-9813R/CDA-9812RX/ CDA-9811R. This will reduce any chance of damage to the unit in case of a short-circuit. Be sure to connect the colour coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage to the vehicle's electrical system. When making connections to the vehicle's electrical system, be aware of the factory installed components (e.g. on-board computer). Do not tap into these leads to provide power for this unit. When connecting the CDA-9815RB/CDA-9813R/ CDA-9812RX/CDA-9811R to the fuse box, make sure the fuse for the intended circuit of the CDA-9815RB/CDA-9813R/ CDA-9812RX/CDA-9811R has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. When in doubt, consult your ALPINE dealer. The CDA-9815RB/CDA-9813R/CDA-9812RX/CDA-9811R uses female RCA-type jacks for connection to other units (e.g. amplifier) having RCA connectors. You may need an adaptor to connect other units. If so, please contact your authorized ALPINE dealer for assistance. Be sure to connect the speaker () leads to the speaker () terminal. Never connect left and right channel speaker cables to each other or to the vehicle body.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT.
Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

IMPORTANT

Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number plate is located on the bottom of the unit.
SERIAL NUMBER: INSTALLATION DATE: INSTALLATION TECHNICIAN: PLACE OF PURCHASE:

Installation

Metal plate
For the screw *, provide a proper screw to the chassis installing location.

 

Tags

1400GTR Dell 1100 System 26PFL5322 12 RQ-2102 SA-6300 Symphony 2610 Extensa 7620 Desktop PC Samsung J808 ENL6298X3 HT-TX35T Yamaha A100 CFD-S100L SC-PMX1 AJ3000 Information L600V XE-A401 AFK BM2 MCD177 12 42PC5DH-UL DL-30 T CNC Ericsson W902 ZWF1220W FLS876C CW2403 C 313 ECM-CZ10 Station Rcs-77h KD-G401 Makita 4326 6337dwde VGN-TX650p-B Singer 45W HD5730 ZM-MFC2 LT4218A Century 1996 SW51-120 LE46A956d1M PX-120 DZ-GX3300E Sedan X XS ZOS5 1 RP200A Ryobi 890R Sedan 2000 KDL-40P3600 PCG-FX604 14PV340 YP-S3jaby HMX-T10BP VS3121 SC-PT470 TS2GPF810W DAT72 P5KPL-VM TL-WR740N Tourist D7 M7 Samsung NX-5 23PF4321-01 Explorer 340 MCD709 P4RD1-MX HVR-M15AE Pantech C300 HI535 DVP6620 ICN520 Trainer PRO Review QW71X SGH-X160B Singer 270 Deere 7000 PC78XL HDR-CX500V LFD23860ST SFC7-18 Powershot G10 DMR-EH50EG Gauge 200 DX Of Isis Lustre 2011 EL-6810 Mpack P600 D1876 Mce KIT Garmin 376C YST-SW320 CDX-4250 AZ1053 12 Software LN-406

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101