CDM-9807RB CDM-9805R CDM-9803RM CDM-9803R CDE-9802RB CDE-9801R

FM/MW/LW/RDS CD Receiver

OWNER'S MANUAL Please read before using this equipment. BEDIENUNGSANLEITUNG Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gertes. MODE D'EMPLOI Veuillez lire avant dutiliser cet appareil. MANUAL DE OPERACIN Lalo antes de utilizar este equipo. ISTRUZIONI PER LUSO Si prega di leggere prima di utilizzare il attrezzatura. ANVNDARHANDLEDNING Innan du anvnder utrustningen br du lsa igenom denna anvndarhandledning.
ALPINE ELECTRONICS MARKETING, INC. 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-0031, Japan Phone 03-5496-8231 ALPINE ELECTRONICS OF AMERICA, INC. 19145 Gramercy Place, Torrance, California 90501, U.S.A. Phone 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF CANADA, INC. 7300 Warden Ave., Suite 203, Markham, Ontario L3R 9Z6, Canada Phone 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD. 6-8 Fiveways Boulevarde Keysborough, Victoria 3173, Australia Phone 03-9769-0000 ALPINE ELECTRONICS GmbH Kreuzerkamp 7, 40878 Ratingen, Germany Phone 02102-4550 ALPINE ELECTRONICS OF U.K. LTD. Alpine House Fletchamstead Highway, Coventry CV4 9TW, U.K. Phone 0870-763
ALPINE ELECTRONICS FRANCE S.A.R.L. (RCS PONTOISE B 280) 98, Rue de la Belle Etoile, Z.I. Paris Nord Il, B.P. 50016, 95945 Roissy Charles de Gaulle Cedex, France Phone 01-48638989 ALPINE ITALIA S.p.A. Viale C. Colombo 8, 20090 Trezzano Sul Naviglio (MI), Italy Phone 02-484781 ALPINE ELECTRONICS DE ESPAA, S.A. Portal de Gamarra 36, Pabelln, Vitoria (Alava)-APDO 133, Spain Phone 945-283588 Designed by ALPINE Japan Printed in China (Y) 68P02294K52-O
Meiyi Printing Factory, Dalian, China No. 28 Chang Qing Street, Xi Gang District, Dalian, China
CHM-S630 CHA-S634 CHA-1214
CD changer for CDM-9807RB/CDM-9805R/ CDM-9803RM/CDM-9803R CD-Wechsler fr CDM-9807RB/CDM-9805R/ CDM-9803RM/CDM-9803R Changeur CD pour CDM-9807RB/CDM9805R/CDM-9803RM/CDM-9803R Cambiador de CD para CDM-9807RB/CDM9805R/CDM-9803RM/CDM-9803R Cambia CD per CDM-9807RB/CDM-9805R/ CDM-9803RM/CDM-9803R CD-vxlare fr CDM-9807RB/CDM-9805R/ CDM-9803RM/CDM-9803R
Alpine CD Changers Give You More!
More musical selections, more versatility, more convenience.
The CHA-S634 is a high-performance 6-disc changer with a new M DAC, CD-R/RW PLAY BACK, MP3 PLAY BACK and CD TEXT. The CHA-1214 Ai-NET model holds 12 discs, and the CHM-S630 M-Bus model is a super-compact 6-disc changer with a CD-R/RW PLAY BACK.
NOTE The CHA-S634 model can be connected to the M-Bus model Head Unit using the optional M-Bus/Ai-NET compatible cable. (KCA-130B)
Von Alpine CD-Wechslern haben Sie mehr!
Mehr Musikauswahl, mehr Vielseitigkeit, mehr Komfort.
Der CHA-S634 ist ein Hochleistungs-Wechsler fr 6 CDs mit dem neuen M-DAC, mit CD-R/RW- und MP3-Wiedergabefunktion und mit CD-TEXT. Der CHA-1214 ist ein Ai-NET-Modell fr 12 CDs. Der M-Bus-kompatible CHM-S630 ist ein superkompakter Wechsler fr 6 CDs mit CD-R/RW-Wiedergabefunktion.
HINWEIS Das Modell CHA-S634 kann mit einem M-Bus-/Ai-NET-kompatiblen Kabel (KCA-130B) an das zustzlich erhltliche M-Bus-Hauptgert angeschlossen werden.
Changeurs de CD Alpine : vous avez le choix!
Plus de slections musicales, plus de souplesse, plus de confort.
Le modle CHA-S634 est un changeur 6 disques ultra performant quip des nouvelles fonctions M DAC, CD-R/RW PLAY BACK, MP3 PLAY BACK et CD TEXT. Le modle CHA-1214 Ai-NET contient 12 disques. Le modle CHM-S630 M-Bus est un changeur 6 disques super compact dot de la fonction CD-R/RW PLAY BACK.
REMARQUE Le modle CHA-S634 peut tre raccord lappareil principal du modle M-Bus en option laide du cble compatible M-Bus/Ai-NET (KCA-130B).
Los cambiadores Alpine de CD le ofrecen ms!
Ms selecciones musicales, ms versatilidad y ms ventajas.
CHA-S634 es un cambiador de seis discos de alto rendimiento con nuevo M DAC, CD-R/RW PLAY BACK, MP3 PLAY BACK y CD TEXT. El modelo CHA-1214 Ai-NET alberga 12 discos y el modelo CHM-S630 M-Bus es un cambiador de seis discos de tamao reducido con un CD-R/RW PLAY BACK.

Information

In Case of Difficulty.. 18 Specifications... 19

Radio Operations

Manual Tuning... 8 Automatic Seek Tuning.. 8 Manual Storing of Station Presets. 9 Automatic Memory of Station Presets.. 9 Tuning to Preset Stations.. 9
Installation and Connections
Warning.. 20 Caution... 20 Precautions.. 20 Installation.. 21 Connection.. 22

RDS Operations

Setting RDS Reception Mode and Receiving RDS Stations.. 10 Recalling Preset RDS Stations.. 10 Receiving RDS Regional (Local) Stations. 11 Receiving Traffic Information. 11 PTY (Programme Type) Tuning.. 11
This symbol means important instructions. Failure to heed them can result in serious injury or death.

CAUTION

This symbol means important instructions. Failure to heed them can result in injury or material property damage.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE.
Any function that requires your prolonged attention should only be performed after coming to a complete stop. Always stop the vehicle in a safe location before performing these functions. Failure to do so may result in an accident.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Centre for repairing.

PRECAUTIONS

Temperature
Be sure the temperature inside the vehicle is between +60C (+140F) and 10C (+14F) before turning your unit on.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISE WHILE DRIVING.
Failure to do so may result in an accident.

Moisture Condensation

You may notice the CD playback sound wavering due to condensation. If this happens, remove the disc from the player and wait about an hour for the moisture to evaporate.
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric shock.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.

Damaged Disc

Do not attempt to play cracked, warped, or damaged discs. Playing a bad disc could severely damage the playback mechanism.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.

Swallowing them may result in serious injury. If swallowed, consult a physician immediately.

Maintenance

If you have problems, do not attempt to repair the unit yourself. Return it to your Alpine dealer or the nearest Alpine Service Station for servicing.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES.
Failure to do so may result in fire or electric shock.
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may result in fire.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in fire, electric shock or other injury.
DO NOT PLACE HANDS, FINGERS OR FOREIGN OBJECTS IN INSERTION SLOTS OR GAPS.
Doing so may result in personal injury or damage to the product.
Never Attempt the Following
Do not grip or pull out the disc while it is being pulled back into the player by the automatic reloading mechanism. Do not attempt to insert a disc into the unit when the unit power is off.

Installation Location

Make sure this unit will not be installed in a location subjected to: Direct sun and heat High humidity and water Excessive dust Excessive vibrations
Handling the Detachable Front Panel
Do not expose to rain or water. Do not drop or apply shock.

Inserting Discs

Your player accepts only one disc at a time for playback. Do not attempt to load more than one disc. Make sure the label side is facing up when you insert the disc. Your player will automatically eject any disc that is inserted incorrectly. If the player continues to eject a correctly inserted disc, push the Reset switch with a pointed object such as a ballpoint pen. Playing a disc while driving on a very bumpy road may result in skips, but this will not scratch the disc or damage the player.

Correct Handling

Do not drop the disc while handling. Hold the disc by its edge so that no fingerprints are left on the surface. Do not FR affix tape, paper, or gummed labels to the disc. Do not write on the disc.

CORRECT

INCORRECT CORRECT

New Discs

As a protective measure to prevent the CD from jamming, the CD player will automatically eject discs with irregular surfaces or inserted incorrectly. When a new disc is inserted into the player and ejected after initial loading, using your finger, feel around the inside of the centre hole and outside edge of the disc. If you feel any small bumps or irregularities, this could inhibit proper loading of the disc. To remove the bumps, rub the inside edge of the hole and outside edge of the disc with a ballpoint pen or other such instrument, then insert the disc again.

Connectable to Remote Control Interface Box (CDM-9807RB/CDM-9805R/CDM-9803RM/ CDM-9803R only) You can operate this unit from the vehicle's control unit when an Alpine Remote Control Interface Box (optional) is connected. For details, contact your Alpine dealer.

Initial System Start-Up

NOTE Before attaching the front panel, make sure that there is no dirt or dust on the connector terminals and no foreign object between the front panel and the main unit.
Immediately after installing or applying power to the unit, it should be initialized. To do this, first, remove the detachable front panel. Behind the front panel, to the right of the connector, there is a small hole. Using a pencil or other pointed object, press the Reset switch mounted behind this hole to complete the initialization procedure.

Reset switch

Turning Power On and Off

Turning Loudness On/Off

Loudness introduces a special low- and highfrequency emphasis at low listening levels. This compensates for the ear's decreased sensitivity to bass and treble sound.
Press the SOURCE/POWER button to turn on the unit.
NOTE The unit can be turned on by pressing any other button except the eject c button.
The volume level gradually increases to the previous level you were listening to before the unit was turned off. Press and hold the SOURCE/POWER button again for at least 3 seconds.
NOTE The very first time the power is turned on, the volume will start from level 12, and the LOUD function will be on in the tuner mode.
Press and hold the MODE/LOUD button for at least 2 seconds to activate or deactivate the loudness mode. The display shows "LOUD ON" when the loudness mode is activated.

Audio Mute Function

Activating this function will instantly lower the volume level by 20 dB.
Adjusting Volume/Balance (Between Left and Right)/Fader (Between Front and Rear)
Press the MODE/LOUD button repeatedly to choose the desired mode. Each press changes the modes as follows: VOL SUB-W* BAL FAD Volume: 0 ~ 35 Balance: L15 ~ R15 Fader: R15 ~ F15 Subwoofer: 0 ~ +15

NOTES If the Rotary encoder (CDM-9807RB/CDM-9805R only) is not turned or the 5 or 6 button (CDM9803RM/CDM-9803R/CDE-9802RB/CDE-9801R only) is not pressed in 5 seconds after selecting the BALANCE and FADER modes, the unit automatically sets in the VOLUME mode. *When the subwoofer is set to ON, the level of the subwoofer can be adjusted.
Press the MUTE button to activate the MUTE mode. The audio level will decrease by about 20 dB. Pressing the MUTE button again will bring the audio back to its previous level. ES
Turn the Rotary encoder (CDM-9807RB/CDM9805R only) or press the 3 and 4 buttons (CDM-9803RM/CDM-9803R/CDE-9802RB/CDE9801R only) until the desired sound is obtained in each mode.
Indicators on the CDM-9807RB/CDM-9805R/ CDM-9803R
The underline is lit when the function is activated.
(CDM-9807RB/CDM-9805R) g BAND Rotary encoder (CDM-9803RM/CDM-9803R/CDE-9802RB/CDE-9801R) g BAND 4

CENTER f

DISP/B. OUT (CDM-9807RB only)

Setting the Bass Control

You can change the Bass Frequency emphasis to create your own tonal preference.
Press the CENTER f button to select the Bass setting mode. Each press changes the modes as follows. mode

Bass setting

The settings of the Bass Level will be individually memorized for each source (FM, MW (LW) and CD) until the setting is changed. Once you set Bass frequency and Bass Band Width for one of sources (FM, MW (LW) and CD), this setting becomes effective for all those sources. * Selecting any of the "Setting the Bass Types" (TYPE 1 through 3), temporarily replaces the custom settings you have made above.

Treble setting

Normal
Setting the Treble Control
You can change the Treble Frequency emphasis to create your own tonal preference.
2-1 Setting the Bass frequency:
Press the g or f button to select the desired Bass centre frequency. 60Hz 80Hz 100Hz 200Hz
Press the CENTER f button to select the Treble setting mode. Each press changes the modes as follows. mode
Emphasizes the displayed Bass frequency ranges.
2-2 Setting the Bass Band Width (Q-Factor):
Press the BAND button to select the desired Bass Band Width. WIDE1 WIDE2 WIDE3 WIDE4 (Narrow).. (Wide) Changes the displayed frequency's band width to narrow or wide.
2-1 Setting Treble frequency:
Press g or f button to select the desired Treble centre frequency. 10kHz 12.5kHz 15kHz 17.5kHz Emphasizes the displayed Treble frequency ranges.
2-3 Setting the Bass Level:
Turn the Rotary encoder (CDM-9807RB/CDM9805R only) or press the 3 or 4 button (CDM9803RM/CDM-9803R/CDE-9802RB/CDE-9801R only) to select the desired Bass Level (-7~+7). You can emphasize or weaken the bass frequency.
NOTES If no buttons are pressed within 15 seconds, the Bass control setting will be turned off automatically.

2-2 Setting Treble Level:
Turn the Rotary encoder (CDM-9807RB/CDM9805R only) or press the 3 or 4 button (CDM9803RM/CDM-9803R/CDE-9802RB/CDE-9801R only) to select the desired Treble Level (-7~+7). You can emphasize the treble frequency.
If no buttons are pressed within 15 seconds, the Treble control setting will be turned off automatically. The settings of the Treble Level will be individually memorized for each source (FM, MW (LW) and CD) until the setting is changed. Once you set Treble frequency for one of sources (FM, MW (LW) and CD), this setting becomes effective for all those sources.

Setting the Bass Type

This function allows for 3 different Bass type settings. Select the one that appeals to you the most.
Changing Audio Level Display Pattern (CDM-9807RB/CDM-9805R only)
Press and hold the CENTER f button for at least 2 seconds to set the Bass type. Select the desired TYPE (1 through 3) by pressing the g or f button within 15 seconds. Type 1 will sound best if you have a subwoofer in your system. Use Type 2 or 3 if you are using small diameter speakers. Press the CENTER f button for at least 2 seconds to return to the normal mode.
NOTES Bass Center Frequency and Bass Band Width previously set are replaced when selecting TYPE 1 through 3. When Bass Type is OFF, your previous settings are restored.
If you connect an external audio processor, the setting cannot be carried out.
Press the DISP button to switch the display pattern. DISP1 DISP2 DISP OFF DISP1: Lights the Volume indicator. DISP2: Lights the mode and value bars to show the settings in the Bass engine display. DISP OFF: Turns off the light in Audio Level display. If you set DISP OFF, the Volume indicator and Bass engine displays are not lit at all times.
Changing Audio Level Display Pattern (CDM-9803RM/CDM-9803R/ CDE-9802RB/CDE-9801R only)
Blackout Mode On and Off (CDM-9807RB only)
When the Blackout mode is turned on, the display will turn off to reduce power consumption. This additional power enhances the sound quality.
Press and hold the F/SETUP button for at least 3 seconds. Press the g or f button to select DISP. Press the BAND button to switch the display pattern. DISP1 DISP2 DISP OFF DISP1: Lights the Volume indicator. DISP2: Lights the mode and value bars to show the settings in the Bass engine display. DISP OFF: Turns off the light in Audio Level display. If you set DISP OFF, the Volume indicator and Bass engine displays are not lit at all times.
Press and hold the DISP/B.OUT button for at least 3 seconds to start the blackout mode. By doing so the display will turn off.
NOTE If any button on the unit is pressed during the blackout mode, the function will be displayed for 5 seconds to show the operation before returning to Blackout mode.
To cancel the blackout mode, press and hold the DISP/B.OUT button for at least 3 seconds.

When the setting is completed, press the F/SETUP button to return to the normal mode.

Automatic Seek Tuning

SOURCE/ POWER TUNE/ A. ME BAND
Press the SOURCE/POWER button to select the radio mode. Press the BAND button repeatedly until the desired radio band is displayed. Each press changes the band: F1(FM1) F2(FM2) MW LW

F/SETUP

Preset buttons (1 through 6)

Manual Tuning

Press the TUNE/A. ME button to illuminate the DX and SEEK indicators in the display. The SEEK indicator illuminates. With the DX mode activated, both strong and weak stations will be tuned in the Auto-Seek operation. Press again to return to the local mode. The DX indicator will turn off and the SEEK indicator will illuminate for a few seconds. Now, only strong stations will be tuned. Press the g or f button to automatically seek a station downward or upward respectively. The unit will stop at the next station it finds. Press the same button again to seek the next station.
Press the TUNE/A. ME button repeatedly until "DX SEEK" and "SEEK" disappear from the display.
NOTE The initial mode is DX SEEK.
Press the g or f button to move downward or upward one step respectively until the desired station frequency is displayed.
NOTE The ST indicator appears on the display when a Stereo FM station is tuned in.
Manual Storing of Station Presets
Select the radio band and tune in a desired radio station you wish to store in the preset memory. Press the F/SETUP button so that the "FUNC" indicator light goes out. Press and hold the Preset buttons (1 through 6) that you want to store the station on for at least 2 seconds. The selected station is stored. The display shows the band, preset No. and station frequency memorized. Repeat the procedure to store up to 5 other stations onto the same band. To use this procedure for other bands, simply select the band desired and repeat the procedure. A total of 24 stations can be stored in the preset memory (6 stations for each band; FM1, FM2, MW and LW).
NOTE If you store a station in a preset memory which already has a station, the current station will be cleared and replaced with the new station.
Automatic Memory of Station Presets
Press the BAND button repeatedly until the desired radio band is displayed. Each press changes the band: F1(FM1) F2(FM2) MW LW
Press and hold the TUNE/A. ME button for at least 2 seconds. The tuner will automatically seek and store 6 strong stations in the selected band in order of signal strength. The frequency on the display continues to change while the automatic memory is in progress. When the automatic memory has been completed, the tuner goes to the station stored in the preset location No. 1.

NOTE If no stations are stored, the tuner will return to the original station you were listening to before the auto memory procedure began.
Tuning to Preset Stations
Press the BAND button repeatedly until the desired band is displayed. Each press changes the band: F1(FM1) F2(FM2) MW LW
Press the F/SETUP button so that the "FUNC" indicator light goes out. Then press the station preset button that has your desired radio station in memory. The display shows the band, preset number and frequency of the station selected.
(CDM-9807RB/CDM-9805R) BAND T.INFO Preset buttons (CDM-9803RM/CDM-9803R/CDE-9802RB/CDE-9801R) BAND Preset buttons

F/SETUP 1/AF 3/PTY

f F/SETUP 1/AF 3/PTY

T.INFO

Setting RDS Reception Mode and Receiving RDS Stations
The RDS (Radio Data System) is a radio information system using the 57 kHz subcarrier of regular FM broadcasts. The RDS allows you to receive a variety of information such as traffic information, station names, and to automatically re-tune to a stronger transmitter that is broadcasting the same programme.
Recalling Preset RDS Stations
Press the F/SETUP button so that the "FUNC" indicator lights up. Press the 1/AF button to activate the RDS mode. Press the F/SETUP button to activate the normal mode. The "FUNC" indicator light goes out. Make sure that the "FUNC" indicator light goes out, then press the preset button in which your desired RDS station is preset. If the preset station's signal is weak, the unit automatically searches and tunes to a stronger station in the AF (Alternative Frequencies) list. If the preset station and the stations in the AF list cannot be received: Press the same preset button again within 5 seconds to have the unit search for a station in the PI (Programme Identification) list. If there are still no stations receivable in the area, the unit displays the frequency of the preset station and the preset indicator disappears. If the signal level of the Regional (Local) station being tuned becomes too weak to receive, press the same preset button to tune in a Regional station in other district.
NOTE For presetting the RDS stations, refer to the Radio Operation section. The RDS stations can be preset in the F1 and F2 bands only.

Press the T.INFO button to deactivate the Traffic Information mode. The "T.INFO" indicator disappears.
About the usable discs. c
Use only compact discs with the label side showing the CD logo marks below.
If you use unspecified compact discs, correct performance cannot be guaranteed. You can play CD-Rs (CD-Recordable)/CD-RWs (CD-ReWritable) for audio use on this unit. You can not also play CD-Rs/CD-RWs containing MP3 formatted audio files.
Some of the following CDs may not play on this unit: Flawed CDs, CDs with fingerprints, CDs exposed to extreme temperatures or sunlight (e.g., left in the car or this unit), CDs recorded under unstable conditions, CDs not designed for audio use, CDs on which a recording failed a re-recording was attempted.

Inserting/Ejecting Disc

Insert a CD half way into the slot with the label side facing up. The player automatically draws the disc into the disc compartment.
On handling Compact Discs (CD/CD-R/ CD-RW)
Do not touch the surface. Do not expose the disc to direct sunlight. Do not affix stickers or labels and do not write on the surface. Clean the disc when it is dusty. Make sure that there are no bumps around thedisc. Do not use commercially available disc accessories. Do not leave the disc in the car or the unit for a long time. Never expose the disc to direct sunlight. Heat and humidity may damage the CD and you may not be able to play it again.
The Disc indicator appears to show that a disc is loaded.
NOTE Three-inch (8cm) CD's can be used.
Press the c button when you want to eject the CD.
NOTES If the CD is not removed for several seconds after it has been ejected, the player automatically draws the CD into the compartment to protect the CD. Do not insert or remove a CD when loading or ejecting a CD, as malfunction may result.
To customers using CD-R/CD-RW
If a CD-R/CD-RW cannot be played back, make sure close session (finalization) has been performed. Finalize the CD-R/CD-RW if necessary, and attempt playback again.

Music Sensor (Skip)

SOURCE/ POWER - / J Preset buttons
Momentarily press the g button once during CD play to return to the beginning of the current track. If you wish to access a track further back, repeatedly press until you reach the desired track. Press the f button once to advance to the beginning of the next track. If you wish to access a track further ahead, press repeatedly until the desired track is reached.
NOTE The music sensor feature is functional in the play or pause mode.

Normal Play and Pause

Fast Forward and Backward
Insert a CD. The CD player begins playback from the first track on the disc.

Press and hold the g or f button to quickly move backward or forward until you reach the desired section of the track.

Repeat Play

The display shows the track number. When the last track is played back the player returns to the first track.
Press the 4 ( ) button to play back repeatedly the track being played. The RPT indicator appears and the track will be played repeatedly. Press the 4 ( the repeat play. ) button again to deactivate
If a disc is already loaded in the CD player, press the SOURCE/POWER button to select the CD mode. Press the -/J button to temporarily stop CD playback. To resume playback, press the -/J button again.
NOTES If a CD Changer is connected and the RPT ALL mode is selected, the unit repeatedly plays back all tracks on the disc selected (CDM-9807RB/CDM9805R/CDM-9803RM/CDM-9803R only). RPT RPT ALL (OFF)
In case a 6-disc CD changer is connected (CDM9807RB/CDM-9805R/CDM-9803RM/CDM-9803R only): Press the F/SETUP button so that the "FUNC" indicator lights up, then go to step 1. Press the F/SETUP button to return to the normal mode. The "FUNC" indicator light goes out.

M.I.X. (Random Play)

Press the 5 ( ) button in the play or pause mode. The M.I.X. indicator will illuminate and the tracks on the disc will be played back in a random sequence. To cancel M.I.X. play, press the 5 ( again. ) button
Controlling CD Changer (Optional) (CDM-9807RB/CDM-9805R/CDM9803RM/CDM-9803R only)
If an optional Alpine 6-disc CD Changer is connected to the 8-pin DIN connector (M-Bus) of the CDM-9807RB/CDM-9805R/CDM-9803RM/ CDM-9803R, you can control the CD Changer using the CDM-9807RB/CDM-9805R/CDM9803RM/CDM-9803R.
NOTE The CD controls on the CDM-9807RB/CDM-9805R/ CDM-9803RM/CDM-9803R for the CD Changer operation are functional only when the CD Changer is interconnected with the CDM-9807RB/CDM-9805R/ CDM-9803RM/CDM-9803R.
NOTE In case a 6-disc CD changer is connected (CDM9807RB/CDM-9805R/CDM-9803RM/CDM-9803R only): Press the F/SETUP button so that the "FUNC" indicator lights up, then go to step 1. Press the F/SETUP button to return to the normal mode. The "FUNC" indicator light goes out.

Scanning Programmes

Press the SOURCE/POWER button to activate the CD Changer.
NOTE To start play or pause play, press the :/J button.
Press the 6 ( ) button to activate the Scan mode. The first 10 seconds of each track will be played back in succession. To stop scanning, press the 6 ( deactivate the Scan mode. ) button to
Make sure that the "FUNC" indicator light goes out, then press the Preset buttons to select the desired disc loaded in the CD Changer.
NOTES After selecting the desired disc, you can operate in the same way as for the CD player. For details, please see the CD Operation section. If the "FUNC" indicator is illuminated the Disc Select buttons become nonfunctional.

SOURCE/ POWER BAND

Setting the AUX Mode (CDM-9807RB/CDM-9805R/CDM9803RM/CDM-9803R only)
You can input TV/video sound by connecting an optional "M-Bus V-Link" (M-Bus/RCA interface cable KCM-122B) to this component.

g f F/SETUP

Press and hold the F/SETUP button for at least 3 seconds. Press the g or f button to select the AUX mode. Press the BAND button to toggle the mode between AUX ON and AUX OFF. Press the F/SETUP button to return to normal mode. To adjust the volume, etc., first press the SOURCE/POWER button and select the AUX mode, then make the necessary adjustment. TUNER CD AUX
NOTE When AUX ON is selected, a CD Changer cannot be used.

Subwoofer On and Off

Press and hold the F/SETUP button for at least 3 seconds. Press the g or f button to select the SUB (Subwoofer) mode. Press the BAND button to select Subwoofer ON or OFF. After setting is completed, press the F/SETUP button to return to normal mode.
NOTES Initial mode is "SUB-W ON." Set to "SUBW OFF" unless the subwoofer is used. When the subwoofer is turned on, the subwoofer output level can be adjusted. For more details, refer to the Adjusting Volume/Balance/Fader.
Adjusting Source Signal Levels
If the difference in volume level between the CD player and FM radio is too great, adjust the FM signal level as follows.
Press and hold the F/SETUP button for at least 3 seconds. Press the g or f button to select the FM LV (FM LEVEL) mode. Press the BAND button to select the FM signal level HI (High) or LO (Low) to make the signal levels between the FM band and CD player closer. Press the F/SETUP button to return to normal mode.

DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.
When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.

IMPORTANT

Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number plate is located on the bottom of the unit. SERIAL NUMBER: INSTALLATION DATE: INSTALLATION TECHNICIAN: PLACE OF PURCHASE:
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT.
Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.
The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.
Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.

Installation

Caution (CDM-9807RB/CDM-9805R only) Do not block the units fan or heat sink, thus preventing air circulation. If blocked, heat will accumulate inside the unit and may cause a fire. Air ventilation hole <Rear side>
Slide the unit into the dashboard. When the unit is in place, make sure the locking pins are fully seated in the down position. This can be done by pressing firmly in on the unit while pushing the locking pin down with a small screwdriver. This ensures that the unit is properly locked and will not accidentally come out from the dashboard. Install the Detachable Front Panel.

HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Centre for repairing.

PRECAUTIONS

Temperature
Be sure the temperature inside the vehicle is between +60C (+140F) and 10C (+14F) before turning your unit on.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISE WHILE DRIVING.
Failure to do so may result in an accident.

Moisture Condensation

You may notice the CD playback sound wavering due to condensation. If this happens, remove the disc from the player and wait about an hour for the moisture to evaporate.
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric shock.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.

Damaged Disc

Do not attempt to play cracked, warped, or damaged discs. Playing a bad disc could severely damage the playback mechanism.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed, consult a physician immediately.

Maintenance

If you have problems, do not attempt to repair the unit yourself. Return it to your Alpine dealer or the nearest Alpine Service Station for servicing.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES.
Failure to do so may result in fire or electric shock.
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may result in fire.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in fire, electric shock or other injury.
DO NOT PLACE HANDS, FINGERS OR FOREIGN OBJECTS IN INSERTION SLOTS OR GAPS.
Doing so may result in personal injury or damage to the product.
Never Attempt the Following
Do not grip or pull out the disc while it is being pulled back into the player by the automatic reloading mechanism. Do not attempt to insert a disc into the unit when the unit power is off.

Reset switch

Turning Power On and Off

Turning Loudness On/Off

Loudness introduces a special low- and highfrequency emphasis at low listening levels. This compensates for the ear's decreased sensitivity to bass and treble sound.
Press the SOURCE/POWER button to turn on the unit.
NOTE The unit can be turned on by pressing any other button except the eject c button.
The volume level gradually increases to the previous level you were listening to before the unit was turned off. Press and hold the SOURCE/POWER button again for at least 3 seconds.
NOTE The very first time the power is turned on, the volume will start from level 12, and the LOUD function will be on in the tuner mode.
Press and hold the MODE/LOUD button for at least 2 seconds to activate or deactivate the loudness mode. The display shows "LOUD ON" when the loudness mode is activated.

Audio Mute Function

Activating this function will instantly lower the volume level by 20 dB.
Adjusting Volume/Balance (Between Left and Right)/Fader (Between Front and Rear)
Press the MODE/LOUD button repeatedly to choose the desired mode. Each press changes the modes as follows: VOL SUB-W* BAL FAD Volume: 0 ~ 35 Balance: L15 ~ R15 Fader: R15 ~ F15 Subwoofer: 0 ~ +15
NOTES If the Rotary encoder (CDM-9807RB/CDM-9805R only) is not turned or the 5 or 6 button (CDM9803RM/CDM-9803R/CDE-9802RB/CDE-9801R only) is not pressed in 5 seconds after selecting the BALANCE and FADER modes, the unit automatically sets in the VOLUME mode. *When the subwoofer is set to ON, the level of the subwoofer can be adjusted.
Press the MUTE button to activate the MUTE mode. The audio level will decrease by about 20 dB. Pressing the MUTE button again will bring the audio back to its previous level. ES
Turn the Rotary encoder (CDM-9807RB/CDM9805R only) or press the 3 and 4 buttons (CDM-9803RM/CDM-9803R/CDE-9802RB/CDE9801R only) until the desired sound is obtained in each mode.
Indicators on the CDM-9807RB/CDM-9805R/ CDM-9803R
The underline is lit when the function is activated.
(CDM-9807RB/CDM-9805R) g BAND Rotary encoder (CDM-9803RM/CDM-9803R/CDE-9802RB/CDE-9801R) g BAND 4

CENTER f

DISP/B. OUT (CDM-9807RB only)

Setting the Bass Control

You can change the Bass Frequency emphasis to create your own tonal preference.

Press the CENTER f button to select the Bass setting mode. Each press changes the modes as follows. mode

Bass setting

The settings of the Bass Level will be individually memorized for each source (FM, MW (LW) and CD) until the setting is changed. Once you set Bass frequency and Bass Band Width for one of sources (FM, MW (LW) and CD), this setting becomes effective for all those sources. * Selecting any of the "Setting the Bass Types" (TYPE 1 through 3), temporarily replaces the custom settings you have made above.

Treble setting

Normal
Setting the Treble Control
You can change the Treble Frequency emphasis to create your own tonal preference.
2-1 Setting the Bass frequency:
Press the g or f button to select the desired Bass centre frequency. 60Hz 80Hz 100Hz 200Hz
Press the CENTER f button to select the Treble setting mode. Each press changes the modes as follows. mode
Emphasizes the displayed Bass frequency ranges.
2-2 Setting the Bass Band Width (Q-Factor):
Press the BAND button to select the desired Bass Band Width. WIDE1 WIDE2 WIDE3 WIDE4 (Narrow).. (Wide) Changes the displayed frequency's band width to narrow or wide.
2-1 Setting Treble frequency:
Press g or f button to select the desired Treble centre frequency. 10kHz 12.5kHz 15kHz 17.5kHz Emphasizes the displayed Treble frequency ranges.
2-3 Setting the Bass Level:
Turn the Rotary encoder (CDM-9807RB/CDM9805R only) or press the 3 or 4 button (CDM9803RM/CDM-9803R/CDE-9802RB/CDE-9801R only) to select the desired Bass Level (-7~+7). You can emphasize or weaken the bass frequency.
NOTES If no buttons are pressed within 15 seconds, the Bass control setting will be turned off automatically.
2-2 Setting Treble Level:
Turn the Rotary encoder (CDM-9807RB/CDM9805R only) or press the 3 or 4 button (CDM9803RM/CDM-9803R/CDE-9802RB/CDE-9801R only) to select the desired Treble Level (-7~+7). You can emphasize the treble frequency.
If no buttons are pressed within 15 seconds, the Treble control setting will be turned off automatically. The settings of the Treble Level will be individually memorized for each source (FM, MW (LW) and CD) until the setting is changed. Once you set Treble frequency for one of sources (FM, MW (LW) and CD), this setting becomes effective for all those sources.

Setting the Bass Type

This function allows for 3 different Bass type settings. Select the one that appeals to you the most.
Changing Audio Level Display Pattern (CDM-9807RB/CDM-9805R only)
Press and hold the CENTER f button for at least 2 seconds to set the Bass type. Select the desired TYPE (1 through 3) by pressing the g or f button within 15 seconds. Type 1 will sound best if you have a subwoofer in your system. Use Type 2 or 3 if you are using small diameter speakers. Press the CENTER f button for at least 2 seconds to return to the normal mode.
NOTES Bass Center Frequency and Bass Band Width previously set are replaced when selecting TYPE 1 through 3. When Bass Type is OFF, your previous settings are restored.
If you connect an external audio processor, the setting cannot be carried out.
Press the DISP button to switch the display pattern. DISP1 DISP2 DISP OFF DISP1: Lights the Volume indicator. DISP2: Lights the mode and value bars to show the settings in the Bass engine display. DISP OFF: Turns off the light in Audio Level display. If you set DISP OFF, the Volume indicator and Bass engine displays are not lit at all times.
Changing Audio Level Display Pattern (CDM-9803RM/CDM-9803R/ CDE-9802RB/CDE-9801R only)
Blackout Mode On and Off (CDM-9807RB only)
When the Blackout mode is turned on, the display will turn off to reduce power consumption. This additional power enhances the sound quality.
Press and hold the F/SETUP button for at least 3 seconds. Press the g or f button to select DISP. Press the BAND button to switch the display pattern. DISP1 DISP2 DISP OFF DISP1: Lights the Volume indicator. DISP2: Lights the mode and value bars to show the settings in the Bass engine display. DISP OFF: Turns off the light in Audio Level display. If you set DISP OFF, the Volume indicator and Bass engine displays are not lit at all times.
Press and hold the DISP/B.OUT button for at least 3 seconds to start the blackout mode. By doing so the display will turn off.
NOTE If any button on the unit is pressed during the blackout mode, the function will be displayed for 5 seconds to show the operation before returning to Blackout mode.
To cancel the blackout mode, press and hold the DISP/B.OUT button for at least 3 seconds.
When the setting is completed, press the F/SETUP button to return to the normal mode.

Automatic Seek Tuning

SOURCE/ POWER TUNE/ A. ME BAND
Press the SOURCE/POWER button to select the radio mode. Press the BAND button repeatedly until the desired radio band is displayed. Each press changes the band: F1(FM1) F2(FM2) MW LW

F/SETUP

Preset buttons (1 through 6)

Manual Tuning

Press the TUNE/A. ME button to illuminate the DX and SEEK indicators in the display. The SEEK indicator illuminates. With the DX mode activated, both strong and weak stations will be tuned in the Auto-Seek operation. Press again to return to the local mode. The DX indicator will turn off and the SEEK indicator will illuminate for a few seconds. Now, only strong stations will be tuned. Press the g or f button to automatically seek a station downward or upward respectively. The unit will stop at the next station it finds. Press the same button again to seek the next station.
Press the TUNE/A. ME button repeatedly until "DX SEEK" and "SEEK" disappear from the display.
NOTE The initial mode is DX SEEK.
Press the g or f button to move downward or upward one step respectively until the desired station frequency is displayed.
NOTE The ST indicator appears on the display when a Stereo FM station is tuned in.
Manual Storing of Station Presets
Select the radio band and tune in a desired radio station you wish to store in the preset memory. Press the F/SETUP button so that the "FUNC" indicator light goes out. Press and hold the Preset buttons (1 through 6) that you want to store the station on for at least 2 seconds. The selected station is stored. The display shows the band, preset No. and station frequency memorized. Repeat the procedure to store up to 5 other stations onto the same band. To use this procedure for other bands, simply select the band desired and repeat the procedure. A total of 24 stations can be stored in the preset memory (6 stations for each band; FM1, FM2, MW and LW).
NOTE If you store a station in a preset memory which already has a station, the current station will be cleared and replaced with the new station.
Automatic Memory of Station Presets
Press the BAND button repeatedly until the desired radio band is displayed. Each press changes the band: F1(FM1) F2(FM2) MW LW
Press and hold the TUNE/A. ME button for at least 2 seconds. The tuner will automatically seek and store 6 strong stations in the selected band in order of signal strength. The frequency on the display continues to change while the automatic memory is in progress. When the automatic memory has been completed, the tuner goes to the station stored in the preset location No. 1.
NOTE If no stations are stored, the tuner will return to the original station you were listening to before the auto memory procedure began.
Tuning to Preset Stations
Press the BAND button repeatedly until the desired band is displayed. Each press changes the band: F1(FM1) F2(FM2) MW LW
Press the F/SETUP button so that the "FUNC" indicator light goes out. Then press the station preset button that has your desired radio station in memory. The display shows the band, preset number and frequency of the station selected.

Press the g and f buttons within 5 seconds after activating the PTY mode to choose the desired programme type while the PTY (programme type) is being displayed. Each press scrolls the programme type by one. LIGHT M CLASSICS OTHER M
Press the 3/PTY button within 5 seconds after selecting the programme type to start searching for a station in the selected programme type. The chosen programme type indicator blinks during searching and lights when a station is found. If no PTY station is found, "NO PTY" will be displayed for 2 seconds.
Press the F/SETUP button to activate the normal mode. The "FUNC" indicator light goes out.
(CDM-9807RB/CDM-9805R) T.INFO (CDM-9803RM/CDM-9803R/CDE-9802RB/CDE-9801R)

2/NEWS

Receiving Traffic Information While Playing CD or Radio

Priority News

This function allows you to preset to give priority to the News programme. You will never miss the News programme as the unit automatically gives priority to the News programme whenever it begins broadcasting, and interrupts the programme you are currently listening. This feature is functional when your unit is set to a mode other than the LW and MW modes.
Press the T.INFO button repeatedly until the "T.INFO" indicator appears in the display. Press the g and f buttons to select a traffic information station if necessary. When a traffic information broadcast starts, the unit automatically mutes the CD player/ changer or the regular FM broadcast. When the traffic information broadcast finishes, the unit automatically returns to the original source play before the traffic information broadcast began.
Press the F/SETUP button so that the "FUNC" indicator lights up while the unit is in Radio (FM receiving) mode. Press the 2/NEWS button to activate the PRIORITY NEWS mode. The "NEWS" indicator appears in the display. To disable the PRIORITY NEWS function, press the NEWS button.
NOTE In the PRIORITY NEWS function, unlike in the T.INFO function, the volume does not increase automatically.

If an optional Alpine 6-disc CD Changer is connected to the 8-pin DIN connector (M-Bus) of the CDM-9807RB/CDM-9805R/CDM-9803RM/ CDM-9803R, you can control the CD Changer using the CDM-9807RB/CDM-9805R/CDM9803RM/CDM-9803R.
NOTE The CD controls on the CDM-9807RB/CDM-9805R/ CDM-9803RM/CDM-9803R for the CD Changer operation are functional only when the CD Changer is interconnected with the CDM-9807RB/CDM-9805R/ CDM-9803RM/CDM-9803R.
NOTE In case a 6-disc CD changer is connected (CDM9807RB/CDM-9805R/CDM-9803RM/CDM-9803R only): Press the F/SETUP button so that the "FUNC" indicator lights up, then go to step 1. Press the F/SETUP button to return to the normal mode. The "FUNC" indicator light goes out.

Scanning Programmes

Press the SOURCE/POWER button to activate the CD Changer.
NOTE To start play or pause play, press the :/J button.
Press the 6 ( ) button to activate the Scan mode. The first 10 seconds of each track will be played back in succession. To stop scanning, press the 6 ( deactivate the Scan mode. ) button to
Make sure that the "FUNC" indicator light goes out, then press the Preset buttons to select the desired disc loaded in the CD Changer.
NOTES After selecting the desired disc, you can operate in the same way as for the CD player. For details, please see the CD Operation section. If the "FUNC" indicator is illuminated the Disc Select buttons become nonfunctional.

SOURCE/ POWER BAND

Setting the AUX Mode (CDM-9807RB/CDM-9805R/CDM9803RM/CDM-9803R only)
You can input TV/video sound by connecting an optional "M-Bus V-Link" (M-Bus/RCA interface cable KCM-122B) to this component.

g f F/SETUP

Press and hold the F/SETUP button for at least 3 seconds. Press the g or f button to select the AUX mode. Press the BAND button to toggle the mode between AUX ON and AUX OFF. Press the F/SETUP button to return to normal mode. To adjust the volume, etc., first press the SOURCE/POWER button and select the AUX mode, then make the necessary adjustment. TUNER CD AUX
NOTE When AUX ON is selected, a CD Changer cannot be used.

Subwoofer On and Off

Press and hold the F/SETUP button for at least 3 seconds. Press the g or f button to select the SUB (Subwoofer) mode. Press the BAND button to select Subwoofer ON or OFF. After setting is completed, press the F/SETUP button to return to normal mode.
NOTES Initial mode is "SUB-W ON." Set to "SUBW OFF" unless the subwoofer is used. When the subwoofer is turned on, the subwoofer output level can be adjusted. For more details, refer to the Adjusting Volume/Balance/Fader.

Adjusting Source Signal Levels
If the difference in volume level between the CD player and FM radio is too great, adjust the FM signal level as follows.
Press and hold the F/SETUP button for at least 3 seconds. Press the g or f button to select the FM LV (FM LEVEL) mode. Press the BAND button to select the FM signal level HI (High) or LO (Low) to make the signal levels between the FM band and CD player closer. Press the F/SETUP button to return to normal mode.
Switching the Tuner Mode (CDM-9807RB/CDM-9805R only)
The CDM-9807RB/CDM-9805R incorporates the MAX TUNE Pro for the highest quality tuner audio. Moreover, you can choose between 3 settings to suit your own personal sound preferences usage.
Press and hold the F/SETUP button for at least 3 seconds. Press the g or f button to select NORMAL. Press the BAND button to switch the TUNER mode. HI-FI NORMAL STABLE
NORMAL: Standard setting HI-FI: Sound quality priority setting STABLE: Noiseless priority setting
NOTES The initial setting at the factory is "NORMAL." If you find the sound is very noisy while listening to the tuner in the HI-FI mode, we recommend you change to the NORMAL mode.

In Case of Difficulty

If you encounter a problem, please turn the power off, then on again. If the unit is still not functioning normally, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer.
CD Player/Changer (CDM-9807RB/CDM-9805R/ CDM-9803RM/CDM-9803R only) not functioning. Out of operating temperature range +50C (+120F) for CD. - Allow the vehicle's interior (or trunk) temperature to cool. CD playback sound is wavering. Moisture condensation in the CD Module. - Allow enough time for the condensation to evaporate (about 1 hour). CD insertion not possible. The CD is already in the CD player. - Eject the CD and remove it. The CD is being improperly inserted. - Make sure the CD is being inserted following instructions in the CD Player Operation section. Unable to fast forward or backward the CD. The CD has been damaged. - Eject the CD and discard it; using a damaged CD in your unit can cause damage to the mechanism. CD playback sound skips due to vibration. Improper mounting of the unit. - Securely re-mount the unit. Disc is very dirty. - Clean the disc. Disc has scratches. - Change the disc. The pick-up lens is dirty. - Do not use a commercial available lens cleaner disc. Consult your nearest ALPINE dealer. CD playback sound skips without vibration. Dirty or scratched disc. - Clean the disc; damaged disc should be replaced. Error displays (built-in CD player only) Mechanical error - Press the c button. After the error indication disappears, insert the disc again. If the abovementioned solution does not solve the problem, consult your nearest ALPINE dealer.

Note When the "ERROR" is displayed: In case that the disc cannot be ejected by pressing the c button, press the Reset switch (refer to page 4) and press the c button again. If not ejecting, consult your Alpine dealer.

MW TUNER SECTION

Tuning Range Sensitivity (IEC Standard)

LW TUNER SECTION

CD SECTION
Frequency Response Wow & Flutter (% WRMS) Total Harmonic Distortion Dynamic Range Signal-to-Noise Ratio Channel Separation

NO DISC

No CD is inserted. - Insert a CD.

PICKUP

Wave Length Laser power

GENERAL

Power Requirement Maximum Power Output
Indication for CD Changer (CDM-9807RB/CDM-9805R/CDM9803RM/CDM-9803R only) HI TEMP

Output Voltage

ERROR - 01
Malfunction in the CD Changer. - Consult your Alpine dealer. Press the magazine eject button and pull out the magazine. Check the indication. Insert the magazine again. If the magazine cannot be pulled out, consult your Alpine dealer. Magazine ejection not possible. - Press the magazine eject button. If the magazine does not eject, consult your Alpine dealer.

Bass Treble Weight

CHASSIS SIZE

Width Height Depth

NOSEPIECE SIZE
Due to continuous product improvement, specifications and design are subject to change without notice.

NO MAGZN

No magazine is loaded into the CD Changer. - Insert a magazine.

CLASS 1 LASER PRODUCT

(Bottom side of player)
No indicated disc. - Choose another disc.
Before installing or connecting the unit, please read the following and pages 2 and 3 of this manual thoroughly for proper use.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire's insulation from being cut by the metal edge of the hole.

Warning

MAKE THE CORRECT CONNECTIONS.
Failure to make the proper connections may result in fire or product damage.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.
Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to electrical shorts.

Precautions

Be sure to disconnect the cable from the () battery post before installing your unit. This will reduce any chance of damage to the unit in case of a short-circuit. Be sure to connect the colour coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage to the vehicle's electrical system. When making connections to the vehicle's electrical system, be aware of the factory installed components (e.g. on-board computer). Do not tap into these leads to provide power for this unit. When connecting this unit to the fuse box, make sure the fuse for the intended circuit of the unit has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. When in doubt, consult your ALPINE dealer. This unit uses female RCA-type jacks for connection to other units (e.g. amplifier) having RCA connectors. You may need an adaptor to connect other units. If so, please contact your authorized ALPINE dealer for assistance. Be sure to connect the speaker () leads to the speaker () terminal. Never connect left and right channel speaker cables to each other or to the vehicle body.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.
When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.

IMPORTANT

Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number plate is located on the bottom of the unit. SERIAL NUMBER: INSTALLATION DATE: INSTALLATION TECHNICIAN: PLACE OF PURCHASE:
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT.
Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.

The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.
Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.

Installation

Caution (CDM-9807RB/CDM-9805R only) Do not block the units fan or heat sink, thus preventing air circulation. If blocked, heat will accumulate inside the unit and may cause a fire. Air ventilation hole <Rear side>
Slide the unit into the dashboard. When the unit is in place, make sure the locking pins are fully seated in the down position. This can be done by pressing firmly in on the unit while pushing the locking pin down with a small screwdriver. This ensures that the unit is properly locked and will not accidentally come out from the dashboard. Install the Detachable Front Panel.

Bracket

Rubber Cap (Included) Hex Bolt (Included) Lock pin Dashboard
Mounting sleeve (Included) No Pressure Here This unit
Removal 1 Remove the detachable front panel. 2 Use a small screwdriver (or similar tool) to push the locking pins to the up position (see Fig. 3). As each pin is unlocked, gently pull out on the unit to make sure it does not re-lock before unlocking the second pin. 3 Pull the unit out, keeping it unlocked as you do so. <JAPANESE CAR>

No Pressure Here

Front frame
Remove the Detachable Front Panel (refer to page 4). Slide mounting sleeve from main unit (see Removal Procedure below). Slide the mounting sleeve into the dashboard.
Metal Mounting Strap Screw
Screws (M5 8) (Included) This unit

Hex Nut (M5)

Bolt Stud
This unit Mounting Bracket
When your vehicle has the Bracket, mount the long hex bolt onto the rear panel of this unit and put the Rubber Cap on the hex bolt. If your vehicle does not have the Mounting Support, reinforce the head unit with the metal mounting strap (not supplied). Connect all the leads of this unit according to details described in the CONNECTIONS section.

# Front Output RCA Connectors (CDM-9807RB/ CDM-9805R/CDM-9803RM/CDM-9803R only) RED is right and WHITE is left. # Rear/Subwoofer* Output RCA Connectors (CDE-9802RB/CDE-9801R only) RED is right and WHITE is left. * When Subwoofer is set to OFF: Output is from Rear
speakers. When Subwoofer is set to ON: Output is from Subwoofer.
$ Rear Output RCA Connectors (CDM-9807RB/CDM-9805R only) RED is right and WHITE is left. $ Rear/Subwoofer* Output RCA Connectors (CDM-9803RM/CDM-9803R only) RED is right and WHITE is left. * When Subwoofer is set to OFF: Output is from Rear
% Power Supply Connector & DIN Connector (CDM-9807RB/CDM-9805R/ CDM-9803RM/CDM-9803R only) Connect this to the DIN connector on the CD changer. ( Left Rear (+) Speaker Output Lead (Green) ) Left Rear () Speaker Output Lead (Green/ Black) ~ Left Front (+) Speaker Output Lead (White) + Left Front () Speaker Output Lead (White/Black) , Right Front () Speaker Output Lead (Grey/ Black) - Right Front (+) Speaker Output Lead (Grey). Right Rear () Speaker Output Lead (Violet/ Black) / Right Rear (+) Speaker Output Lead (Violet) : ISO Connector (Speaker Output) ; DIN Extension Cable (Included with CD changer)
NOTE Older Alpine CD changer came with standard, straight type DIN connectors. In installations where an L-type connector would simplify installation, the Alpine 491002 Adaptor can be used (sold separately). < Subwoofer Output RCA Connectors (CDM-9807RB/CDM-9805R only) RED is right and WHITE is left. = RCA Extension Cable (sold separately)

! "

For details on how to set the Subwoofer to ON/OFF, see "Subwoofer On and Off" on page 16.
To prevent external noise from entering the audio system. Locate the unit and route the leads at least 10 cm away from the car harness. Keep the battery power leads as far away from other leads as possible. Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis. If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise suppressors, contact them for further information. Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.