This symbol means important instructions. Failure to heed them can result in injury or material property damage.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE.
Any function that requires your prolonged attention should only be performed after coming to a complete stop. Always stop the vehicle in a safe location before performing these functions. Failure to do so may result in an accident.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Centre for repairing.

PRECAUTIONS

Temperature
Be sure the temperature inside the vehicle is between +60C (+140F) and 10C (+14F) before turning your unit on.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISE WHILE DRIVING.
Failure to do so may result in an accident.
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric shock.

Moisture Condensation

You may notice the CD playback sound wavering due to condensation. If this happens, remove the disc from the player and wait about an hour for the moisture to evaporate.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.

Damaged Disc

Do not attempt to play cracked, warped, or damaged discs. Playing a bad disc could severely damage the playback mechanism.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed, consult a physician immediately.

Maintenance

If you have problems, do not attempt to repair the unit yourself. Return it to your Alpine dealer or the nearest Alpine Service Station for servicing.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES.
Failure to do so may result in fire or electric shock.
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may result in fire.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in fire, electric shock or other injury.
DO NOT PLACE HANDS, FINGERS OR FOREIGN OBJECTS IN INSERTION SLOTS OR GAPS.
Doing so may result in personal injury or damage to the product.
Never Attempt the Following
Do not grip or pull out the disc while it is being pulled back into the player by the automatic reloading mechanism. Do not attempt to insert a disc into the unit when the unit power is off.

Installation Location

Make sure this unit will not be installed in a location subjected to: Direct sun and heat High humidity and water Excessive dust Excessive vibrations

Handling the Detachable Front Panel
Do not expose to rain or water. Do not drop or apply shock.

Inserting Discs

Your player accepts only one disc at a time for playback. Do not attempt to load more than one disc. Make sure the label side is facing up when you insert the disc. Your player will automatically eject any disc that is inserted incorrectly. If the player continues to eject a correctly inserted disc, push the Reset switch with a pointed object such as a ballpoint pen. Playing a disc while driving on a very bumpy road may result in skips, but this will not scratch the disc or damage the player.

Correct Handling

Do not drop the disc while handling. Hold the disc by its edge so that no fingerprints are left on the surface. Do not FR affix tape, paper, or gummed labels to the disc. Do not write on the disc.

CORRECT

INCORRECT CORRECT

New Discs

As a protective measure to prevent the CD from jamming, the CD player will automatically eject discs with irregular surfaces or inserted incorrectly. When a new disc is inserted into the player and ejected after initial loading, using your finger, feel around the inside of the centre hole and outside edge of the disc. If you feel any small bumps or irregularities, this could inhibit proper loading of the disc. To remove the bumps, rub the inside edge of the hole and outside edge of the disc with a ballpoint pen or other such instrument, then insert the disc again.
Centre Hole Centre Hole New Disc Outside (Bumps)

Disc Cleaning

Fingerprints, dust, or soil on the surface of the disc couldDE cause the CD player to skip. For routine cleaning, wipe the playing surface with a clean, soft cloth from the centre of the disc to the outer edge. If the surface is heavily soiled, dampen a clean, soft cloth in a solution of mild neutral detergent before cleaning the disc.

Disc Accessories

There are various accessories available on the market for protecting the disc surface and improving sound quality. However, most of them will influence the thickness and/or diameter of the disc. Using such accessories can cause the SE disc to be out of standard specifications and may create operational problems. We recommend not using these accessories on discs played in Alpine CD players.

Irregular Shaped Discs

Be sure to use round shape discs only for this unit and never use any special shape discs. Use of special shape discs may cause damage to the mechanism.

Transparent Sheet

Disc Stabilizer
(CDM-9825RB) SOURCE/ POWER (CDM-9823RR/CDM-9823R/CDE-9822RB/CDE-9821RM/ CDE-9821R) MODE / LOUD (Rotary encoder) SOURCE/ POWER 4 MODE / LOUD
Detaching the Front Panel
Connectable to Remote Control Interface Box You can operate this unit from the vehicle's control unit when an Alpine Remote Control Interface Box (optional) is connected. For details, contact your Alpine dealer.
Press and hold the SOURCE/POWER button for at least 3 seconds to turn off the power. Press the (Release) button at lower left corner until the front panel pops out. Grasp the left side of the front panel and pull it out.

Initial System Start-Up

NOTES The front panel may become hot in normal usage (especially the connector terminals), this is not a malfunction. To protect the front panel, place it in the supplied carrying case.
Immediately after installing or applying power to the unit, it should be initialized. To do this, first, remove the detachable front panel. Behind the front panel, to the right of the connector, there is a small hole. Using a pencil or other pointed object, press the Reset switch mounted behind this hole to complete the initialization procedure.
Attaching the Front Panel
First, insert the right side of the front panel into the main unit. Align the groove on the front panel with the projection on the main unit. Push the left side of the front panel until it locks firmly into the main unit.

Reset switch

NOTE Before attaching the front panel, make sure that there is no dirt or dust on the connector terminals and no foreign object between the front panel and the main unit.

Turning Power On and Off

Turning Loudness On/Off
Loudness introduces a special low- and highfrequency emphasis at low listening levels. This compensates for the ear's decreased sensitivity to bass and treble sound.

2-1 Setting the Bass frequency:
Press the g or f button to select the desired Bass centre frequency. 60Hz 80Hz 100Hz 200Hz
Press the CENTER f button to select the Treble setting mode. Each press changes the modes as follows. mode
Emphasizes the displayed Bass frequency ranges.
2-2 Setting the Bass Band Width (Q-Factor):
Press the BAND button to select the desired Bass Band Width. WIDE1 WIDE2 WIDE3 WIDE4 (Narrow).. (Wide) Changes the displayed frequency's band width to narrow or wide.
2-1 Setting Treble frequency:
Press g or f button to select the desired Treble centre frequency. 10kHz 12.5kHz 15kHz 17.5kHz Emphasizes the displayed Treble frequency ranges.
2-3 Setting the Bass Level:
Turn the Rotary encoder (CDM-9825RB only) or press the 3 or 4 button (CDM-9823RR/CDM9823R/CDE-9822RB/CDE-9821RM/CDE-9821R only) to select the desired Bass Level (-7~+7). You can emphasize or weaken the bass frequency.
NOTES If no buttons are pressed within 15 seconds, the Bass control setting will be turned off automatically.
2-2 Setting Treble Level:
Turn the Rotary encoder (CDM-9825RB only) or press the 3 or 4 button (CDM-9823RR/CDM9823R/CDE-9822RB/CDE-9821RM/CDE-9821R only) to select the desired Treble Level (-7~+7). You can emphasize the treble frequency.
If no buttons are pressed within 15 seconds, the Treble control setting will be turned off automatically. The settings of the Treble Level will be individually memorized for each source (FM, MW (LW) and CD) until the setting is changed. Once you set Treble frequency for one of sources (FM, MW (LW) and CD), this setting becomes effective for all those sources.

Setting the Bass Type

This function allows for 3 different Bass type settings. Select the one that appeals to you the most.
Changing Audio Level Display Pattern (CDM-9823RR/CDM-9823R/ CDE-9822RB/CDE-9821RM/CDE9821R only)
Press and hold the CENTER f button for at least 2 seconds to set the Bass type. Select the desired TYPE (1 through 3) by pressing the g or f button within 15 seconds. Type 1 will sound best if you have a subwoofer in your system. Use Type 2 or 3 if you are using small diameter speakers. Press the CENTER f button for at least 2 seconds to return to the normal mode.
NOTE Bass Center Frequency and Bass Band Width previously set are replaced when selecting TYPE 1 through 3. When Bass Type is OFF, your previous settings are restored.
Press and hold the F/SETUP button for at least 3 seconds. Press the g or f button to select DISP. Press the BAND button to switch the display pattern. DISP1 DISP2 DISP OFF
DISP1: Lights the Volume indicator. DISP2: Lights the mode and value bars to show the settings in the Bass engine display. DISP OFF: Turns off the light in Audio Level display. If you set DISP OFF, the Volume indicator and Bass engine displays are not lit at all times.
Changing Audio Level Display Pattern (CDM-9825RB only)

When the setting is completed, press the F/SETUP button to return to the normal mode.
Press the DISP button to switch the display pattern. DISP1 DISP2 DISP OFF DISP1: Lights the Volume indicator. DISP2: Lights the mode and value bars to show the settings in the Bass engine display. DISP OFF: Turns off the light in Audio Level display. If you set DISP OFF, the Volume indicator and Bass engine displays are not lit at all times.

Automatic Seek Tuning

SOURCE/ TUNE/ POWER A. ME BAND
Press the SOURCE/POWER button to select the radio mode. Press the BAND button repeatedly until the desired radio band is displayed. Each press changes the band: F1(FM1) F2(FM2) MW LW

F/SETUP

Preset buttons (1 through 6)

Manual Tuning

Press the TUNE/A. ME button to illuminate the DX and SEEK indicators in the display. The SEEK indicator illuminates. With the DX mode activated, both strong and weak stations will be tuned in the Auto-Seek operation. Press again to return to the local mode. The DX indicator will turn off and the SEEK indicator will illuminate for a few seconds. Now, only strong stations will be tuned. Press the g or f button to automatically seek a station downward or upward respectively. The unit will stop at the next station it finds. Press the same button again to seek the next station.
Press the TUNE/A. ME button repeatedly until "DX SEEK" and "SEEK" disappear from the display.
NOTE The initial mode is DX SEEK.
Press the g or f button to move downward or upward one step respectively until the desired station frequency is displayed.
NOTE The ST indicator appears on the display when a Stereo FM station is tuned in.
Manual Storing of Station Presets
Tuning to Preset Stations
Select the radio band and tune in a desired radio station you wish to store in the preset memory. Press the F/SETUP button so that the "FUNC" indicator light goes out. Press and hold the Preset buttons (1 through 6) that you want to store the station on for at least 2 seconds. The selected station is stored. The display shows the band, preset No. and station frequency memorized. Repeat the procedure to store up to 5 other stations onto the same band. To use this procedure for other bands, simply select the band desired and repeat the procedure. A total of 24 stations can be stored in the preset memory (6 stations for each band; FM1, FM2, MW and LW).
NOTE If you store a station in a preset memory which already has a station, the current station will be cleared and replaced with the new station.
Press the BAND button repeatedly until the desired band is displayed. Each press changes the band: F1(FM1) F2(FM2) MW LW
Press the F/SETUP button so that the "FUNC" indicator light goes out. Then press the station preset button that has your desired radio station in memory. The display shows the band, preset number and frequency of the station selected.

Automatic Memory of Station Presets
Press the BAND button repeatedly until the desired radio band is displayed. Each press changes the band: F1(FM1) F2(FM2) MW LW
Press and hold the TUNE/A. ME button for at least 2 seconds. The tuner will automatically seek and store 6 strong stations in the selected band in order of signal strength. The frequency on the display continues to change while the automatic memory is in progress. When the automatic memory has been completed, the tuner goes to the station stored in the preset location No. 1.
NOTE If no stations are stored, the tuner will return to the original station you were listening to before the auto memory procedure began. Indicators on the CDM-9825RB/CDM-9823R
(CDM-9825RB) BAND T.INFO Preset buttons (CDM-9823RR/CDM-9823R/CDE-9822RB/CDE-9821RM/ CDE-9821R) BAND Preset buttons

F/SETUP 1/AF 3/PTY

f F/SETUP 1/AF 3/PTY

T.INFO

Setting RDS Reception Mode and Receiving RDS Stations
The RDS (Radio Data System) is a radio information system using the 57 kHz subcarrier of regular FM broadcasts. The RDS allows you to receive a variety of information such as traffic information, station names, and to automatically re-tune to a stronger transmitter that is broadcasting the same programme.
Recalling Preset RDS Stations
Press the F/SETUP button so that the "FUNC" indicator lights up. Press the 1/AF button to activate the RDS mode. Press the F/SETUP button to activate the normal mode. The "FUNC" indicator light goes out. Make sure that the "FUNC" indicator light goes out, then press the preset button in which your desired RDS station is preset. If the preset station's signal is weak, the unit automatically searches and tunes to a stronger station in the AF (Alternative Frequencies) list. If the preset station and the stations in the AF list cannot be received: Press the same preset button again within 5 seconds to have the unit search for a station in the PI (Programme Identification) list. If there are still no stations receivable in the area, the unit displays the frequency of the preset station and the preset indicator disappears. If the signal level of the Regional (Local) station being tuned becomes too weak to receive, press the same preset button to tune in a Regional station in other district.

NOTE For presetting the RDS stations, refer to the Radio Operation section. The RDS stations can be preset in the F1 and F2 bands only.
Press the F/SETUP button so that the "FUNC" indicator lights up. Press the 1/AF button to activate the RDS mode. Press the g or f button to tune in the desired RDS station.
NOTE When the BAND button is pressed and held for more than 2 seconds while a station name is displayed, the display shows the station frequency for 5 seconds.
Press the 1/AF button again to deactivate the RDS mode. Press the F/SETUP button to activate the normal mode. The "FUNC" indicator light goes out.
Tips The RDS digital data includes the following: PI Programme Identification PS Programme Service Name AF List of Alternative Frequencies TP Traffic Programme TA Traffic Announcement PTY Programme Type EON Enhanced Other Networks
Receiving RDS Regional (Local) Stations
PTY (Programme Type) Tuning
Press and hold the F/SETUP button for at least 3 seconds to activate the setting mode. Press the g or f button to select the REG mode. Press the BAND button to turn on or off the REG (Regional) mode. In the REG OFF mode, the unit automatically keeps receiving the related local RDS station. Press the F/SETUP button to deactivate the setting mode.
Press the F/SETUP button so that the "FUNC" indicator lights up. Press the 3/PTY button to activate the PTY mode, while the unit is in Radio (FM receiving) mode. The Programme Type of the station being currently received will be displayed for 5 seconds. If there is no receivable PTY broadcast, "NO PTY" will be displayed for 5 seconds. If no RDS station can be received, the display shows "NO PTY."
NOTE If no button is pressed within 5 seconds after pressing the PTY button, the PTY mode will be automatically cancelled.
Receiving Traffic Information
Press the T.INFO button repeatedly until the T.INFO indicator appears in the display. Press the g or f button to select your desired traffic information station. When a traffic information station is tuned in, the TP indicator lights up. Traffic information is heard only when it is being broadcast. If traffic information is not being broadcast, the unit is set in the standby mode. When a traffic information broadcast begins, the unit automatically receives it and the display shows "TRF-INFO" for a few seconds and returns to the PS display. When the traffic information broadcast is over, the unit will automatically set in the standby mode.
NOTES If the traffic information broadcast signal falls below a certain level, the unit remains in the receiving mode for 1 minute. If the signal remains below a certain level for over 1 minute, the "T.INFO" indicator blinks. If you do not want to listen to the traffic information being received, lightly press the T.INFO button to skip that traffic information message. The T. INFO mode will remain in the ON position to receive the next traffic information message. If the volume level is changed while receiving traffic information, the changed volume level will be memorized. When traffic information is received next time, the volume level will be automatically adjusted to the level memorized.

Scanning Programmes

Press the SOURCE/POWER button to activate the CD Changer.
NOTE To start play or pause play, press the :/J button.
Press the 6 ( ) button to activate the Scan mode. The first 10 seconds of each track will be played back in succession. To stop scanning, press the 6 ( deactivate the Scan mode. ) button to
Make sure that the "FUNC" indicator light goes out, then press the Preset buttons to select the desired disc loaded in the CD Changer.
NOTES After selecting the desired disc, you can operate in the same way as for the CD player. For details, please see the CD Operation section. If the "FUNC" indicator is illuminated the Disc Select buttons become nonfunctional.

SOURCE/ POWER BAND

Setting the AUX Mode (CDM-9825RB/CDM-9823RR/CDM9823R only)
You can input TV/video sound by connecting an optional "M-Bus V-Link" (M-Bus/RCA interface cable KCM-122B) to this component.

g f F/SETUP

Press and hold the F/SETUP button for at least 3 seconds. Press the g or f button to select the AUX mode. Press the BAND button to toggle the mode between AUX ON and AUX OFF. Press the F/SETUP button to return to normal mode. To adjust the volume, etc., first press the SOURCE/POWER button and select the AUX mode, then make the necessary adjustment. TUNER CD AUX
NOTE When AUX ON is selected, a CD Changer cannot be used.

Subwoofer On and Off

Press and hold the F/SETUP button for at least 3 seconds. Press the g or f button to select the SUB (Subwoofer) mode. Press the BAND button to select Subwoofer ON or OFF. After setting is completed, press the F/SETUP button to return to normal mode.
NOTES Initial mode is "SUB-W ON." Set to "SUBW OFF" unless the subwoofer is used. When the subwoofer is turned on, the subwoofer output level can be adjusted. For more details, refer to the Adjusting Volume/Balance/Fader.
Adjusting Source Signal Levels
If the difference in volume level between the CD player and FM radio is too great, adjust the FM signal level as follows.

No function or display. Vehicle's ignition is off. - If connected following instructions, the unit will not operate with the vehicle's ignition off. Improper power lead connections. - Check power lead connections. Blown fuse. - Check the fuse on the battery lead of the unit; replace with the proper value if necessary. Internal micro-computer malfunctioned due to interference noise etc. - Press the Reset switch with a ballpoint pen or other pointed article.
Unable to receive stations. No antenna or open connection in cable. - Make sure the antenna is properly connected; replace the antenna or cable if necessary. Unable to tune stations in the seek mode. You are in a weak signal area. - Make sure the tuner is in the DX mode. If the area you are in is a primary signal area, the antenna may not be grounded and connected properly. - Check your antenna connections; make sure the antenna is properly grounded at its mounting location. The antenna may not be the proper length. - Make sure the antenna is fully extended; if broken, replace the antenna with a new one. Broadcast is noisy. The antenna is not the proper length. - Extend the antenna fully; replace it if it is broken. The antenna is poorly grounded. - Make sure the antenna is grounded properly at its mounting location.
Indication for CD HI TEMP
Protective circuit is activated due to high temperature. - The indicator will disappear when the temperature returns to within operation range.

Specifications

FM TUNER SECTION
Tuning Range Mono Usable Sensitivity Alternate Channel Selectivity Signal-to-Noise Ratio Stereo Separation Capture Ratio 87.5 108.0 MHz 0.7 V 80 dB 65 dB 35 dB 2.0 dB 531 1,602 kHz 25.1 V/28 dB kHz 31.6 V/30 dB 5 20,000 Hz (1 dB) Below measurable limits 0.008% (at 1 kHz) 95 dB (at 1 kHz) 105 dB 85 dB (at 1 kHz) 795 nm CLASS I 14.4 V DC (1116 V allowable) 50 W 4 (CDM-9825RB/CDM9823RR/CDM-9823R) 45 W 4 (CDE-9822RB/CDE9821RM/CDE-9821R) 2 V/10k ohms 14 dB at 60 Hz 14 dB at 10 kHz 1.5 kg (3 lbs. 5 oz) 178 mm (7") 50 mm (2") 160 mm (6-5/16") 170 mm (63/4") 46 mm (1-13/16") 20 mm (25/32")
Mechanism error. 1. Press the c button and eject the CD. If not ejecting, consult your Alpine dealer. 2. When the error indication remains after ejecting, press the c button again. If the error indication still does not turn off after pressing the c button for a few times, consult your Alpine dealer.
Note When the "ERROR" is displayed: In case that the disc cannot be ejected by pressing the c button, press the Reset switch (refer to page 4) and press the c button again. If not ejecting, consult your Alpine dealer.

MW TUNER SECTION

Tuning Range Sensitivity (IEC Standard)

LW TUNER SECTION

CD SECTION
Frequency Response Wow & Flutter (% WRMS) Total Harmonic Distortion Dynamic Range Signal-to-Noise Ratio Channel Separation

PICKUP

NO DISC
No CD is inserted. - Insert a CD.

Wave Length Laser power

GENERAL
Power Requirement Maximum Power Output
Indication for CD Changer (CDM-9825RB/CDM-9823RR/CDM-9823R only) HI TEMP
Output Voltage Bass Treble Weight

CHASSIS SIZE

ERROR - 01
Malfunction in the CD Changer. - Consult your Alpine dealer. Press the magazine eject button and pull out the magazine. Check the indication. Insert the magazine again. If the magazine cannot be pulled out, consult your Alpine dealer. Magazine ejection not possible. - Press the magazine eject button. If the magazine does not eject, consult your Alpine dealer.

Width Height Depth

NOSEPIECE SIZE
Due to continuous product improvement, specifications and design are subject to change without notice.

NO MAGZN

No magazine is loaded into the CD Changer. - Insert a magazine.

CLASS 1 LASER PRODUCT

(Bottom side of player)
No indicated disc. - Choose another disc.
Before installing or connecting the unit, please read the following and pages 2 and 3 of this manual thoroughly for proper use.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire's insulation from being cut by the metal edge of the hole.

Warning

MAKE THE CORRECT CONNECTIONS.
Failure to make the proper connections may result in fire or product damage.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.
Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.

DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT.
Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.
The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.
Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.

Installation

Caution (CDM-9825RB only) Do not block the units fan or heat sink, thus preventing air circulation. If blocked, heat will accumulate inside the unit and may cause a fire. Air ventilation hole <Rear side>
Slide the unit into the dashboard. When the unit is in place, make sure the locking pins are fully seated in the down position. This can be done by pressing firmly in on the unit while pushing the locking pin down with a small screwdriver. This ensures that the unit is properly locked and will not accidentally come out from the dashboard. Install the Detachable Front Panel.

Bracket

Rubber Cap (Included) Hex Bolt (Included) Dashboard

Lock pin

Mounting sleeve (Included) This unit No Pressure Here
Removal 1 Remove the detachable front panel. 2 Use a small screwdriver (or similar tool) to push the locking pins to the up position (see Fig. 3). As each pin is unlocked, gently pull out on the unit to make sure it does not re-lock before unlocking the second pin. 3 Pull the unit out, keeping it unlocked as you do so. <JAPANESE CAR>

No Pressure Here

Front frame
Remove the Detachable Front Panel (refer to page 4). Slide mounting sleeve from main unit (see Removal Procedure below). Slide the mounting sleeve into the dashboard.
Metal Mounting Strap Screw Bolt Stud This unit

Screws (M5 8) (Included)

Hex Nut (M5)

This unit

When your vehicle has the Bracket, mount the long hex bolt onto the rear panel of this unit and put the Rubber Cap on the hex bolt. If your vehicle does not have the Mounting Support, reinforce the head unit with the metal mounting strap (not supplied). Connect all the leads of this unit according to details described in the CONNECTIONS section.
NOTE For the screw , provide a proper screw to the chassis installing location.

Mounting Bracket

Connection

(Orange) DIMMER

ISO Antenna Convertor Plug

Antenna ISO Antenna Plug

(CDM-9825RB/CDE-9822RB only) (Pink/Black) (Blue/White) AUDIO INTERRUPT IN REMOTE TURN-ON

To the instrument cluster illumination lead To vehicle phone
To amplifier or equalizer To power antenna

IGNITION

(Black) GND (Blue) POWER ANT

Ignition Key

(Yellow)

BATTERY

Battery

"

% ( ) ~ + , :. / ;
(CDM-9825RB/CDM-9823RR/CDM-9823R only)

Speakers Rear Left

Green/Black White

Front Left

White/Black Grey/Black Grey Violet/Black

Front Right Rear Right

Violet
CD changer (Sold separately)

< =

(CDM-9825RB only)

Amplifier

Subwoofers

Rear (CDM-9825RB only)

Rear or Subwoofers* (CDM-9823RR/ CDM-9823R only) Rear or Subwoofers* (CDE-9822RB/ CDE-9821RM/CDE9821R only)
Front (CDM-9825RB/CDM9823RR/CDM-9823R only)
1 Antenna Receptacle Connect to the supplied ISO antenna convertor plug. 2 Dimmer Lead (Orange) (CDM-9825RB/ CDE-9822RB only) This lead may be connected to the vehicles instrument cluster illumination lead. This will enable the vehicles dimmer control to dim the backlighting of the unit. 3 Audio Interrupt In Lead (Pink/Black) Connect this lead to the Audio Interface output of a cellular phone which provides ground shorting when a call is received. If a device having the interrupt feature is connected, audio will be automatically muted whenever the interrupt signal is received from the device. 4 Remote Turn-On Lead (Blue/White) Connect this lead to the remote turn-on lead of your amplifier or signal processor. 5 Switched Power Lead (Ignition) (Red) Connect this lead to an open terminal on the vehicles fuse box or another unused power source which provides (+) 12V only when the ignition is turned on or in the accessory position. 6 Ground Lead (Black) Connect this lead to a good chassis ground on the vehicle. Make sure the connection is made to bare metal and is securely fastened using the sheet metal screw provided. 7 Power Antenna Lead (Blue) Connect this lead to the +B terminal of your power antenna, if applicable.

Sony XR-CA Sony/Pioneer Sony XR-L 500 V 2001 Sony/Pioneer Sony XR-L 500 X 2001 Sony/Pioneer Sony XR-M Sony/Pioneer Sony CDX-CA 600 X 2002 Sony/Pioneer Sony CDX-CA 700 X 2002 Sony/Pioneer Sony CDX-CA Sony/Pioneer Sony CDX-L 420 V 2002 Sony/Pioneer Sony CDX-M Sony/Pioneer Sony CDX-M Sony/Pioneer Sony CDX-MP Sony/Pioneer Sony CDX-MP Sony/Pioneer Sony KP-CD 600 X 2002 Sony/Pioneer Sony KP-XR 630 X 2002 Sony/Pioneer Sony XR-CA 630 X 2002 Sony/Pioneer Sony CDX-CA 680 X 2003 Sony/Pioneer Sony CDX-L 580X 2003 Sony/Pioneer Sony CDX-M 1000 TF 2003 Sony/Pioneer Sony CDX-M Sony/Pioneer Sony CDX-M 850 MP 2003 Sony/Pioneer Sony CDX-MP Sony/Pioneer Sony CDX-MP Sony/Pioneer Sony KP-DS 680 XMP 2003 Sony/Pioneer Sony MDX-CA 790 X 2003 Sony/Pioneer Sony MDX-M Sony/Pioneer Sony XR-CA 670 X 2003 Sony/Pioneer Sony CDX-F Sony/Pioneer Sony CDX-F Sony/Pioneer Sony CDX-F Sony/Pioneer Sony CDX-F Sony/Pioneer Sony CDX-M Sony/Pioneer Sony CDX-M Sony/Pioneer Sony CDX-R Sony/Pioneer Sony CDX-R Sony/Pioneer Sony CDX-S Sony/Pioneer Sony KP-CT 670 X 2004 Sony/Pioneer Sony KP-CT 670 XMP 2004 Sony/Pioneer Sony MDX-F Sony/Pioneer Sony CDX-DAB Sony/Pioneer Sony CDX-F Sony/Pioneer Sony CDX-F 7750 S 2005 Sony/Pioneer Sony CDX-M Sony/Pioneer Sony CDX-NC Sony/Pioneer Sony CDX-R Sony/Pioneer Sony CDX-R Sony/Pioneer Seite 13 Radioliste Sony CDX-R Sony/Pioneer Sony CDX-R Sony/Pioneer Sony CDX-S Sony/Pioneer Sony MEX-RSony/Pioneer
Sony CDX-DABSony/Pioneer Sony CDX-F50M 2006 Sony/Pioneer Sony CDX-F50M 2006 Sony/Pioneer Sony CDX-GTSony/Pioneer Sony CDX-GT300S 2006 Sony/Pioneer Sony CDX-GTSony/Pioneer Sony CDX-GT700D 2006 Sony/Pioneer Sony CDX-R30M 2006 Sony/Pioneer Sony CDX-RSony/Pioneer Sony CDX-RASony/Pioneer Sony CDX-RASony/Pioneer Sony MEX-1 GP 2006 Sony/Pioneer Sony MEX-RSony/Pioneer Sony MEX-BTSony/Pioneer Sony CDX-GT610U 2007 Sony/Pioneer Seite 14 Autoliste Fahrzeugliste www.Lenkradfernbedienung.de Marke Modell Baujahre Shop-Kabel Alfa Alfa 147 Modelle mit Multifunktionslenkrad Alfa/Citroen Alfa 156 Modelle mit Multifunktionslenkrad Alfa/Citroen GT Modelle mit Multifunktionslenkrad Alfa/Citroen Audi Abis 01/2001 VW/Audi Abis 01/2001 VW/Audi Abis 01/2001 VW/Audi Abis 01/2001 VW/Audi Abis 01/2001 VW/Audi TT 1996 bis 01/2001 VW/Audi Chevrolet Alle aktuellen Modelle (ausser Captiva) Chevi Deawoo Alle aktuellen Modelle Chevi Nissan Micra K12 Ab 2003 (Bordcomputer luft!) Nissan 1 Note Ab 2003 (Bordcomputer luft!) Nissan 1 X-Trail Nissan X-Trail Ford Focus bis Modell 2004 Ford 1 Mondeo bis Modell 2004 Ford 1 Mondeo mit Blp. Navi (ISO) bis Modell 2004 Ford 3 Focus C-MAX ab Modell 2004 Ford 2 Ford Mondeo (MOST) ab Modell 2004 Ford 2 Galaxy ohne Inneraum CAN Modell 2005 VW/Audi Focus (MOST) ab Modell 2004 Ford 2 Opel alle aktuellen Modelle bis Mod.2005 Opel Ohne MOST-Stecker Peugeot in Vorbereitung Renault 96 bis 2002 Renault Display Alle Modelle (bitte Anleitung MIT exter-nem anfordern!) Display Renault Twingo 98 bis 00 Renault 10-Pol Clio I und II 90 bis 00 Renault 10-Pol OHNE