Center Hole Bumps Outside (Bumps) Center Hole New Disc

Damaged Disc

Do not attempt to play cracked, warped, or damaged discs. Playing a bad disc could severely damage the playback mechanism.

Maintenance

If you have problems, do not attempt to repair the unit yourself. Return it to your Alpine dealer or the nearest Alpine Service Station for servicing.
Never Attempt the Following
Do not grip or pull out the disc while it is being pulled back into the player by the automatic reloading mechanism. Do not attempt to insert a disc into the unit when the unit power is off.

Irregular Shaped Discs

Be sure to use round shape discs only for this unit and never use any special shape discs. Use of special shape discs may cause damage to the mechanism.

Installation Location

Make sure the IVA-C801/CVA-1006 will not be installed in a location subjected to: Direct sun and heat High humidity and water Excessive dust Excessive vibrations

Disc Accessories

There are various accessories available on the market for protecting the disc surface and improving sound quality. However, most of them will influence the thickness and/or diameter of the disc. Using such accessories can cause the disc to be out of standard specifications and may create operational problems. We recommend not using these accessories on discs played in Alpine CD players.

Correct Handling

Do not drop the disc while handling. Hold the disc so you will not leave fingerprints on the surface. Do not affix tape, paper, or gummed labels to the disc. Do not write on the disc.

CORRECT

Transparent Sheet

Disc Stabilizer

Handling the Detachable Front Panel
Do not expose to rain or water. Do not drop or apply shock. After turning the system off, a slight ghost of the image will remain temporarily. This is an effect peculiar to LCD technology and is normal. Under cold temperature conditions, the screen may lose contrast temporarily. After a short warm-up period, it will return to normal. Alpine products equipped with the Ai-NET bus, connected to the IVA-C801/CVA-1006, can be operated from the IVA-C801/CVA-1006. Depending on the products connected, the functions and displays will vary. For details, consult your Alpine dealer.

INCORRECT

Disc Cleaning
Fingerprints, dust, or soil on the surface of the disc could cause the CD player to skip. For routine cleaning, wipe the playing surface with a clean, soft cloth from the center of the disc to the outer edge. If the surface is heavily soiled, dampen a clean, soft cloth in a solution of mild neutral detergent before cleaning the disc.
Remove the anti-theft cover when you drive. This prevents the cover from falling off the unit and interfering with the safe operation of the vehicle. Operation of some of the functions of this unit is very complex. Because of this, it was deemed necessary to place these functions into a special screen. This will restrict operation of these functions to times when the vehicle is parked. This ensures the focus of the driver's attention will be on the road and not on the IVA-C801/ CVA-1006. This has been done for the safety of the driver and passengers. Title Input and Audio Processor Adjustments cannot be made if the car is moving. The car must be parked and the parking brake must be engaged for the procedure described in the Owner's Manual to be valid. The warning "CAN'T OPERATE WHILE DRIVING," will be displayed if any attempts are made to perform these operations while driving. This operation is the same as when selecting sources using the remote control. When the car is parked, the selection is made as described in the Owner's Manual.

NOTES The IVA-C801/CVA-1006 is a precision device. With gentle handling, its unique capabilities can be enjoyed for a long time. If the monitor touches an obstacle while it is being raised, the unit will stop raising the monitor immediately. Should this occur, remove the obstacle and press the OPEN/CLOSE button again to lower the monitor. When the movable monitor is opened, do not place any object on the monitor and be careful not to bump or apply any pressure to the monitor while it is open. This can cause damage to the mechanism. Under low ambient temperature conditions, the display may be dark for a short period of time immediately after the power is turned on. Once the LCD has warmed up, the display will return to normal. For your safety, some operation of the unit cannot be performed while the vehicle is in motion. In this case, first stop the vehicle and engage the parking brake, then perform the operation. Operation of the remote control (described on pages 52-53) can be carried out even while the monitor screen is closed.

Initial System Start-UP

RESET switch (CVA-1006)

RESET switch

Immediately after installing or applying power to the unit, it should be initialized. Press the RESET switch with a ball-point pen or any other pointed object.

Lowering the Monitor

Selecting the Monitor Opening Angle
The monitor opening angle can be set in 2 positions.
Press the OPEN/CLOSE button. The unit will beep 3 times and lower the monitor automatically.
NOTES The IVA-C801/CVA-1006 is a precision device. With gentle handling, its unique capabilities can be enjoyed for a long time. If the monitor touches an obstacle while it is being lowered, the unit will stop lowering the monitor immediately. Should this occur, remove the obstacle and press the OPEN/CLOSE button again to lower the monitor.
Press and hold the OPEN/CLOSE button for at least 2 seconds while the monitor is being raised. Each press changes the monitor angle back or forth.
Adjusting the Monitor Viewing Angle
Adjust the monitor's angle for better visibility.

Turning Power On or Off

Some of this unit's functions, cannot be performed while the vehicle is in motion. Be sure to stop your vehicle in a safe location and apply the parking brake, before attempting these operations.
Press the and buttons to adjust the monitor's angle so the screen will be in the best viewing position. Each press of the buttons produces a beep and changes the screen angle between 80 and 104 degrees.
NOTES If the monitor touches an obstacle while the angle is being adjusted the unit will stop the screen immediately. Should this happen, remove the obstacle and press the or button again. The screen color will vary when viewed at certain angles. Adjust the screen angle for the best viewing position. If the voltage of the vehicle's battery power is low, the screen may blink when the screen angle is changed. This is normal and not a malfunction.

NOTES If the disc is not titled, the display shows "NO TITLE CD." If no disc is loaded, the display shows "NO DISC." Pressing the LIST or FUNC (RETURN) button while the list of the disc titles is being displayed, changes the display back to the CD/CD Changer mode screen. To directly go to the preset radio station list screen, press the 1 (RADIO) button. Then, press the BAND button to change the radio band. IVA-C801: Pressing the 2 button displays the title list or the track title list only when a CD with text is loaded in the built-in CD player. CVA-1006: When a CD player or CD changer is connected, pressing the 2 button displays the CD title list.
Controlling CD Changer (Optional)
An optional 6-disc or 12-disc CD Changer may be connected to the IVA-C801/CVA-1006 if it is AiNET compatible. With a CD Changer connected to the Ai-NET input of the IVA-C801/CVA-1006, the CD Changer will be controllable from the IVAC801/CVA-1006. Using the KCA-400C (the Multi-Changer Switching device) multiple changers can be controlled by the IVA-C801/CVA-1006. See the Multi-Changer Selection section on this page for selecting the CD Changers. You can directly select the CD changer mode by pressing the CHG (IVA-C801) or CHANGER (CVA1006) button.

Multi-Changer Selection

Alpine's Ai-NET system will support up to 6 CD Changers. When operating two or more changers, the KCA-400C (Multi-Changer Switching device) must be used. If you use 1 Switching device, you can connect up to 4 CD Changers. If you use 2 Switching devices, you can connect up to 6 CD Changers.
Press the SOURCE button to display the main menu. Rotate the rotary encoder to select changer 1-4 (when one KCA-400C is connected) or changer 1-6 (when two KCA-400Cs are connected). Then press the rotary encoder. The display shows the selected CD changer mode screen. NOTE
When one KCA-400C is connected to the changer, "Changer 1-4" is displayed in the main menu. When two KCA-400Cs are connected to the changer, "Changer 1-6" is displayed in the main menu.

Press the 5 (M.I.X.) button in the play or pause mode. The M.I.X. indicator will illuminate and the tracks on the disc will be played back in a random sequence. After all the tracks on the disc have been played back once, the player will begin a new random sequence play until the M.I.X. mode is deactivated. To stop the M.I.X. play, press the 5 (M.I.X.) button repeatedly until the M.I.X. indicator disappears.
Scrolling Displayed Titles
The MD player can scroll titles (disc or track names) having up to a maximum of 32 characters when it is connected.
Press the 6 (SCROLL) button repeatedly while an MD is being played. Each press toggles between the MD title scrolling and track title scrolling. Press and hold the 6 (SCROLL) button for at least 2 seconds to start the auto scrolling. The title will be scrolled repeatedly. To deactivate the auto scrolling, press and hold the 6 (SCROLL) button for at least 2 seconds.
NOTES Depending on the MD deck used for recordings/ inputting titles, the characters may not be displayed correctly. If the MD title or track titles are not memorized, the unit displays "NO TITLE."

FUNC SOURCE

Controlling Cassette Player
If an optional Alpine cassette player is connected to the IVA-C801/CVA-1006 it can be controlled from the IVA-C801/CVA-1006.
Fast Forward/Rewind/Reversing Tape Direction/Pause
Press the SOURCE button to display the main menu screen. Rotate the rotary encoder and select "TAPE" from the menu. Then, press the rotary encoder to execute the selection. The display shows the cassette player mode screen. When you play a cassette tape recorded using Dolby B Noise Reduction, press the 5 (DOLBY B) button to activate or deactivate Dolby B Noise Reduction. To stop tape play and eject the cassette tape, press the eject (c) button on the cassette player.
Press and hold the 3 (f) or 1 (g) button for at least 2 seconds to fast forward or fast rewind the tape respectively. When the tape reaches the desired portion, press and hold the 3 (f) or 1 (g) button again for at least 2 seconds, or press the 2 (:/J) button to resume tape play. Press the FUNC (PROG) button to change the tape direction to play the other side of the tape. Press the 2 (:/J) button to temporarily pause the tape play. Press again to resume tape play.

Program Sensor

Lightly press the 1 (g) button once during tape play to return to the beginning of the program being currently played. If you wish to return to a program further back, press repeatedly until the number of programs you would like to skip is obtained. Lightly press the 3 (f) button once during tape play to advance to the beginning of the next program. If you wish to advance to a program further ahead, press repeatedly until the number of programs you would like to skip is obtained.
Press the 4 (REPEAT) button to play back repeatedly the program being currently played. To stop the repeat play, press the 4 (REPEAT) button until the REPEAT indicator disappears.

Blank Skip

Press the 6 (B.SKIP) button during tape play to skip over blank portions of the tape lasting 15 seconds or longer. To deactivate the blank skip mode, press the 6 (B.SKIP) button for a second time.

Playing DVD/Video CD/CD

If an optional Alpine DVD/video CD/CD player is connected to the IVA-C801/CVA-1006, you can control it from the IVA-C801/CVA-1006. WARNING It is dangerous (and illegal in many states) for the driver to watch the TV/Video while driving the vehicle. The driver may be distracted from looking ahead and an accident could occur. Install the IVA-C801/CVA-1006 correctly so that the driver cannot watch TV/Video unless the vehicle is stopped and the emergency brake is applied. If the IVA-C801/CVA-1006 is not installed correctly, the driver will be able to watch the TV/ Video while driving the vehicle and may be distracted from looking ahead causing an accident. The driver or other people could be severely injured. To activate your auxiliary devices: To watch a video source, your vehicle must be parked with the ignition key in the ACC or ON position. To do this, follow the procedure below. 1. Push the foot brake to bring your vehicle to a complete stop at a safe location. Engage the parking brake. 2. Keep pushing the foot brake and release the parking brake once then engage it again. 3. While the parking brake is being engaged the second time, release the foot brake.

Press the SOURCE button. The main menu screen appears on the display. Rotate the rotary encoder and select "AUX", then press the rotary encoder to execute the selection.
NOTE If the AUX mode is not displayed on the main menu, select "AUX IN" in the Setup mode screen. Either AUX1 or AUX2 should be turned ON.
Selecting Factory (Maker's) Equalization Presets
If an optional Alpine Equalizer is connected to the IVA-C801/CVA-1006, the Equalizer can be controlled from the IVA-C801/CVA-1006. Six equalization curves are preset on the Equalizer at the factory.
NOTE When the FUNC (RETURN) button is pressed, the display returns to the previous screen. Tip In the equalizer mode, for example, you can horizontally scroll each of the mode screens by rotating the rotary encoder to the left or right. You can also adjust the volume level by pressing and rotating the rotary encoder (DHE, Surround, BBE, listening position, time collection mode main screen only).
Press the SOURCE button. The main menu screen appears on the display. Press the 4 (A.PROC) button to display the list of the Audio Processors (A.PROC). Rotate the rotary encoder and select "Equalizer." Then press the rotary encoder to execute the selection. The display changes to the Equalizer mode screen. Select a desired Equalizer characteristic curve and press the corresponding Function button (1 (FLAT) through 6 (NEWS)). You can select your desired equalizer characteristic curve from 6 preset characteristic curves; FLAT, MALE, FEMALE, POPS, ROCK and NEWS. When you have selected your desired characteristic curve, press the FUNC (RETURN). The display returns to the Audio Processor List screen.
Creating Personal Equalizer Characteristic Curves
You can create your own equalizer characteristic curves. The following is the procedure.
NOTE The Parking Brake must be engaged to access the Equalizer Adjustment mode screen. Attempting to access this screen while driving will display the warning-CAN'T OPERATE WHILE DRIVING.
Selecting Factory Surround Mode Presets
Depending upon the music source you listen to, you can choose your desired surround mode from 6 factory-preset surround modes.
Press the SOURCE button. The main menu screen appears. Press the 4 (A.PROC) button. The Audio Processor list will be displayed. Turn the rotary encoder and select "Surround" then press the rotary encoder. The Surround mode screen appears. Press the Function button (1 through 6) that has your desired surround mode.

Adjustment of Time Correction Value
Adjusting Cross-Over (X-Over) Point of 2-Way Divider
If an optional Alpine Channel Divider PRA-H400 is connected, you can control the Divider from the IVA-C801/CVA-1006. Use this procedure when one or two 2-waysystem or 3-way system channel dividers are connected.
Press the SOURCE button. The main menu appears on the display. Press the 4 (A.PROC) button. The Audio Processor List appears. Rotate the rotary encoder and select the "TimeCorr." (Time-Correction), then press the rotary encoder. The display changes to the Time-Correction mode screen. Press and hold the FUNC (RETURN) button for at least 2 seconds. The display changes to the Time-Correction Adjustment mode screen. Press the rotary encoder repeatedly to select the position (seat) you wish to adjust. Each press changes the seat positions as follows:
Fr/Left Fr/Righ Rear/Left Rear/Right
Press the SOURCE button. The main menu screen appears on the display. Press the 4 (A.PROC) button. The display shows the Audio Processor list screen. Rotate the rotary encoder and select the "Divider" (when one divider is connected) or "Divider-F and Divider-R" (when two dividers are connected), then press the rotary encoder to execute the selection. The display changes to the Divider mode screen. Press and hold the FUNC (RETURN) button for at least 2 seconds. The mode changes to the Divider Adjustment mode. Press the 1 (X-OVER) button. The mode changes to the Cross-Over Adjustment mode.
Rotate the rotary encoder clockwise or counterclockwise to increase or decrease the Time-Correction value respectively to your desired value. When adjustment has been completed, press the FUNC (RETURN) button. The display returns to the Time-Correction mode screen.
Press the rotary encoder and select the channel that you wish to adjust. Each press changes the channel as follows. When only one 2-way divider is connected:

Low F-High R-High

Adjusting Levels
Press and hold the FUNC (RETURN) button for at least 2 seconds in the Divider mode. The mode changes to the Divider Adjustment mode. Press the 2 (LEVEL) button. The mode changes to the Level Adjustment mode. Press the rotary encoder and select the channel you wish to adjust. Each press changes the channels as follows: When only one 2-way system divider is connected:
L-Low R-Low F-High/L R-High/R R-High/L F-High/R
When two 2-way dividers are connected:

Recalling Memorized Divider Settings Using Function Buttons
Display the Divider mode screen. Press the Function button 1 (P.SET1) through 4 (P.SET4) that has your desired divider settings. The divider setting stored at the Function button will be recalled.
Tip You can also recall your desired divider settings memorized by pressing the 4 (;P.DN) or 5 (:P.UP) button in the Divider mode.
Memorizing Characteristic Curves
Equalization characteristic curves created by yourself or factory preset can be stored in memory. (See page 27.)
Select one of the factory preset characteristic curves or make your own (personal) characteristic curve. Then, display the Audio Processor List and select "Private Memo." Press and hold any one of the Function buttons 1 (P.SET1) through 6 (P.SET6) for at least 2 seconds. The Function Guide indicators P.SET1 through P.SET6 in the preset mode display blink indicating that you can memorize the characteristic curve. While the Function Guide indicators are blinking, press the Function button 1 (P.SET1) through 6 (P.SET6) into which you wish to memorize the characteristic curve. Now, the characteristic curve has been memorized. Repeat this procedure to memorize other characteristic curves.
NOTE This unit can memorize curves together with the settings of the equalizer, DHE, BBE and Surround Time Correction.
Recalling Memorized Characteristic Curves Using Function Buttons
Selecting Characteristic Curves from Displayed Audio Processor List
You can select your desired characteristic curves directly from the Audio Processor (A.PROC) List without switching to individual mode screens.
Activate the desired mode, DHE, BBE, surround, time correction or equalizer, then press the Function button 1 (P.SET1) through 6 (P.SET6) that has your desired characteristic curve. The selected characteristic curve is recalled.
Display the Audio Processor List screen. Rotate the rotary encoder and select the desired mode by moving the cursor. The Function Guide for the selected mode is displayed. Press the Function buttons 1 through 6 that has your desired characteristic curve. The list shows the details of the curve selected.

Press the SOURCE button. The main menu screen appears on the display. Press the 6 (SETUP) button. The Setup mode screen appears. Rotate the rotary encoder and select "MIX LEVEL." The Function Guide is displayed. Press the 2 (DOWN) or 3 (UP) button to adjust the volume level of the navigation system's voice guidance in 7 steps. To turn off the navigation interrupt mode, press the 1 (OFF) button. Press the FUNC (RETURN) button to return to the main menu screen.
NOTES Immediately after inputting titles or changing the settings of Setup Mode or Display Mode (While the system is inputting the titles or data automatically) do not turn the ignition key (engine key) to OFF. Otherwise, the title may not be written, or the settings may not be changed. When the voice guidance of the Navigation system starts to interrupt the audio, the display is automatically changed to the navigation screen. The volume level of the audio will be automatically reduced when the voice guidance of the Navigation system starts.

Setting Visual Mode

For direct access to the different visual screens, preset the Navigation or the V. SEL mode. You can then display the screen of the preset item by just pressing the V. SEL button on the IVA-C801/CVA1006.

Setting Bass Frequency

Press the SOURCE button. The main menu screen appears on the display. Press the 6 (SETUP) button. The Setup mode screen appears. Rotate the rotary encoder and select "VISUAL." The Function Guide is displayed. Press the 1 (NAV.) or 2 (V. SEL) to preset the desired item. When "NAVI" is preset: Pressing the V. SEL button directly switches to the navigation screen. When "V. SEL" is preset: Each press of the V. SEL button switches the modes:

NAVI. AUX1 AUX2 DISPLAY

Press the SOURCE button. The main menu appears on the display. Press the 6 (SETUP) button. The Setup mode screen appears. Rotate the rotary encoder and select "BASS Cont." to activate the Bass Control mode. Press the Function button 1 (60 Hz) through 4 (100 Hz) that has the frequency you wish to control. Press the FUNC (RETURN) button. The display returns to the main menu screen.

NOTES Immediately after inputting titles or changing the settings of Setup Mode or Display Mode (While the system is inputting the titles or data automatically) do not turn the ignition key (engine key) to OFF. Otherwise, the title may not be written, or the settings may not be changed. When an equalizer or digital sound processor is connected, this function is inoperative. After carrying out the steps 1 to 3 of "To display the Setup mode screen" described on page 40, perform the operation show below.

Selecting Rear Monitor

If a rear-seat monitor and a navigation system are connected to the IVA-C801/CVA-1006, you can switch the picture/sound of the rear-seat monitor from the IVA-C801/CVA-1006. Immediately after inputting titles or changing the settings of Setup Mode or Display Mode (While the system is inputting the titles or data automatically) do not turn the ignition key (engine key) to OFF. Otherwise, the title may not be written, or the settings may not be changed.
NOTES If the DVD player or DVD changer is connected to the AUX1 terminal. The DVD picture appears by performing steps 1 and 2 of "Playing 2 Sources Simultaneously" on page 51. Then, perform steps 1 to 4 on this page so the DVD picture and sound are output. To deactivate the mode, press the same button. If no particular picture is selected for the rear-seat monitor in the AUX OUT mode, the rear-seat monitor displays the same picture as for the IVA-C801/CVA1006. After carrying out the steps 1 to 3 of "To display the Setup mode screen" described on page 40, perform the operation show below.
Press the SOURCE button. The main menu appears on the display. Press the 6 (SETUP) button. The Setup mode screen appears. Rotate the rotary encoder and select "AUX OUT." The Function Guide is displayed. Press the 1 (NAV.) button, the navigation screen will be displayed and the voice guidance will be produced on the rear-seat monitor if the navigation system is connected. When the 2 (AUX1) button is pressed, the picture/sound of the device connected to Terminal AUX 1 will be played on the rear-seat monitor. When the 3 (AUX2) button is pressed, the picture/sound of the device connected to Terminal AUX 2 will be played on the rear-seat monitor.

Displaying Time

Press the 3 ( DN) or 4 (UP ) button to delay or advance the minutes respectively. Press the FUNC (RETURN) button after adjusting the clock. The display returns to the main menu screen.
NOTE To quickly set the time to the nearest hour, press the 5 (TIME RESET) button. If the displayed time is before the half hour, pressing the 5 (TIME RESET) button sets the clock back to the previous hour. If the displayed time is after the half hour, pressing the 5 (TIME RESET) button sets the clock forward to the beginning of the next hour.

Setting Automatic Opening/ Closing of Monitor
When the Automatic Opening/Closing mode is "ON," the monitor automatically opens when the ignition key is turned to the "ACC" or "ON" position. The monitor automatically closes when the ignition key is turned OFF.
Adjusting Brightness of Picture
To switch to the display mode screen or to the picture mode: To watch a video source, your vehicle must be parked with the ignition key in the ACC or ON position. To do this, follow the procedure below. 1. Push the foot brake to bring your vehicle to a complete stop at a safe location. Engage the parking brake. 2. Keep pushing the foot brake and release the parking brake once then engage it again. 3. While the parking brake is being engaged the second time, release the foot brake.
Press the SOURCE button. The main menu appears on the display. Press the 6 (SETUP) button. The Setup mode screen appears. Rotate the rotary encoder and select "AUTO OPEN." The display shows the Function Guide. Press the 2 (ON) button to set the Auto Opening mode ON. To set the Auto Opening mode OFF, press the 1 (OFF) button. If set to the "OFF" position, the monitor should be manually opened or closed by pressing the OPEN/CLOSE button. Press the FUNC (RETURN) button, the display returns to the main menu screen.
Now, the locking system for the Display mode operation has been released. Unless the ignition key is turned to the OFF position, the Display mode can be activated by engaging the parking brake without performing the above procedure (1 through 3). Each time the ignition key is turned to the OFF position, perform the above procedure.
Press the SOURCE button. The main menu appears on the display. Press the 5 (DISPLAY) button. The Display mode screen appears. Rotate the rotary encoder and select "BRIGHT" to activate the Brightness Adjustment mode. The display shows the Function Guide. Press the 1 (; DARK) to make the picture darker or press the 3 (LIGHT :) to make the picture brighter. You can adjust the brightness between MIN (15) and MAX (+15). When it reaches the minimum or maximum point, the display shows "MIN" or "MAX" respectively. To quickly set to the center position, press the 2 (0) button. When the adjustment has been completed, press the FUNC (RETURN) button. The display returns to the main menu screen.
NOTES With the Display mode screen displayed, pressing and rotating the rotary encoder can adjust the volume level. Immediately after inputting titles or changing the settings of Setup Mode or Display Mode (While the system is inputting the titles or data automatically) do not turn the ignition key (engine key) to OFF. Otherwise, the title may not be written, or the settings may not be changed.

Controls on Remote Control
1 Power Button Press the button to turn the power on/off. 2 Source Button Press to select the audio source. 3 -/J Button Press and hold this button for at least 2 seconds to play or pause (In CD/MD/TAPE/Changer mode). Enter Button Press to execute the selection. (The same function as the rotary encoder on IVA-C801/ CVA-1006.) Pressing and holding this button for at least 2 seconds turns the loudness on or off (when neither an equalizer nor a digital sound processor is connected). 4 ANGLE 89 Buttons Press the button to adjust the angle of the movable display. 5 Band/Program Button Radio mode: BAND Button Press the button and the band will change as shown below. FM1 FM2 AM Changer mode: BAND Button Switches changers (when a Multi-Changer Switching device is connected). TAPE mode: PROG Button Press the button to change between the A and B side of the tape. 6 Volume Adjustment Buttons To increase the volume level: Press the L button To decrease the volume level: Press the K button The buttons have the same functions as rotating the rotary encoder on IVA-C801/CVA-1006.
Owner's Manual of the external audio processor you purchased. This button is used in conjunction with an optional AiNET processor.

Remote sensor

Battery Replacement
Applicable battery: Use two "AAA" sized dry batteries or equivalent.
Point the remote control transmitter toward the remote sensor on the IVA-C801/CVA-1006 and use the remote control within 2 meters from the IVA-C801/CVA-1006.
Replacing the battery Put the batteries in the case observing the polarities as illustrated.
Opening the battery cover Slide out the battery cover while firmly pressing the direction of arrow.
Closing the cover Push the cover as illustrated until a click is heard.

In Case of Difficulty

If you encounter a problem, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer. Unclear picture display. Fluorescent tube is exhausted. - Replace the fluorescent tube*. * The fluorescent tube replacement is not free of charge even within the warranty period, for the tube is an article of consumption.

Remote Control Operation

Controls on Remote Control.. 54 Battery Replacement.. 55

Information

In Case of Difficulty.. 56 Specifications.. 59
Installation and Connections
Warning... 60 Caution.. 60 Precautions.. 60 Installation.. 61 Connections.. 64
* US and foreign patents licensed from Dolby Laboratories.

Other Useful Features

Displaying Spectrum Analyzer (IVX-C806 only)... 39 Displaying Spectrum Analyzer (IVX-M706/CVA-1006R only). 40 Turning Defeat Mode On and Off. 40 Titling CDs.. 41 Adjusting Subwoofer Level (when subwoofer is used with other speakers).. 42 Switching Phase... 43 Setting the External Device Interrupt Mode. 43
This symbol means important instructions. Failure to heed them can result in serious injury or death.

CAUTION

This symbol means important instructions. Failure to heed them can result in injury or material property damage.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE.
Any function that requires your prolonged attention should only be performed after coming to a complete stop. Always stop the vehicle in a safe location before performing these functions. Failure to do so may result in an accident.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Centre for repairing.
DO NOT MIX NEW BATTERIES WITH OLD BATTERIES. INSERT WITH THE CORRECT BATTERY POLARITY.
When inserting the batteries, be sure to observe proper polarity (+ and ) as instructed. Rupture or chemical leakage from the battery may cause fire or personal injury.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISE WHILE DRIVING.
Failure to do so may result in an accident.
KEEP FINGERS AWAY WHILE THE MOTORIZED FRONT PANEL OR MOVING MONITOR IS IN MOTION.
Failure to do so may result in personal injury or damage to the product.
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric shock.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed, consult a physician immediately.

USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES.
Failure to do so may result in fire or electric shock.
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may result in fire.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in fire, electric shock or other injury.
DO NOT PLACE HANDS, FINGERS OR FOREIGN OBJECTS IN INSERTION SLOTS OR GAPS.
Doing so may result in personal injury or damage to the product.

PRECAUTIONS

Temperature
Be sure the temperature inside the vehicle is between +45C (+113F) and 0C (+32F) before turning your unit on.

Inserting Discs

Your player accepts only one disc at a time for playback. Do not attempt to load more than one disc. Make sure the label side is facing up when you insert the disc. Your player will automatically eject any disc that is inserted incorrectly. If the player continues to eject a correctly inserted disc, push the RESET switch with a pointed object such as a ballpoint pen. Playing a disc while driving on a very bumpy road may result in skips, but this will not scratch the disc or damage the player.

Moisture Condensation

You may notice the Disc playback sound wavering due to condensation. If this happens, remove the disc from the player and wait about an hour for the moisture to evaporate.

New Discs

As a protective measure to prevent the CD from jamming, the CD player will automatically eject discs with irregular surfaces or inserted incorrectly. When a new disc is inserted into the player and ejected after initial loading, using your finger, feel around the inside of the centre hole and outside edge of the disc. If you feel any small bumps or irregularities, this could inhibit proper loading of the disc. To remove the bumps, rub the inside edge of the hole and outside edge of the disc with a ballpoint pen or other such instrument, then insert the disc again.
Centre Hole Bumps Outside (Bumps) Centre Hole New Disc

Damaged Disc

Do not attempt to play cracked, warped, or damaged discs. Playing a bad disc could severely damage the playback mechanism.

Maintenance

If you have problems, do not attempt to repair the unit yourself. Return it to your Alpine dealer or the nearest Alpine Service Station for servicing.
Never Attempt the Following
Do not grip or pull out the disc while it is being pulled back into the player by the automatic reloading mechanism. Do not attempt to insert a disc into the unit when the unit power is off.

NOTES Some of this unit's functions, cannot be performed while the vehicle is in motion. Be sure to stop your vehicle in a safe location and apply the parking brake, before attempting these operations. The IVX-C806/IVX-M706/CVA-1006R draws minimal current even when its power switch is turned off. If the switched power (ignition) lead of the IVX-C806/IVXM706/CVA-1006R is connected directly to the positive (+) post of the vehicle's battery, the battery may be discharged. If this lead is unswitched, it must be disconnected from the battery post should the vehicle be left unused for an extended period of time. An SPST (Single-Pole, Single-Throw) switch (sold separately) can be added to simplify this procedure. Then, you can simply place it in the OFF position when you leave the vehicle. Turn the SPST switch back ON before using the IVX-C806/IVX-M706/CVA1006R. For connecting the SPST switch, refer to "Connection Diagram of SPST switch" on page 63. Some operation of the unit cannot be performed while the vehicle is in motion. In this case, be sure to first stop your vehicle and apply the parking brake, then perform the operation.
(IVX-C806) MUTE (IVX-M706. with MD built-in CVA-1006R. without MD built-in) MUTE

SOURCE Rotary encoder

Adjusting the Volume/Bass/Treble/ Balance (Between Left and Right)/ Fader (Between Front and Rear)
Turning Loudness On or Off
Loudness introduces a special low- and highfrequency emphasis at low listening levels. This compensates for the ear's decreased sensitivity to bass and treble sound.
NOTE When an equalizer or digital sound processor is connected, this function is inoperative.
Press the rotary encoder repeatedly until the mode you wish to adjust is obtained. Each press changes the modes as follows:

BAS. TRE. BAL. FAD. VOL.

The volume level can be adjusted at any time by just rotating the rotary encoder.
NOTE When the subwoofer mode is ON, its level may also be adjusted.
Press and hold the rotary encoder for at least 2 seconds to switch between the Loudness On and Off modes.
Adjusting Source Signal Levels
If the difference in volume level between the CD/ MD player and FM radio is too great, adjust the FM signal level as follows.
Rotate the rotary encoder to set to the desired sound within 5 seconds after selecting the mode.
NOTE If the rotary encoder is not turned or pressed within 5 seconds after selecting the BAS. (Bass), TRE. (Treble), BAL. (Balance), or FAD. (Fader), the unit automatically defaults back to the VOL. (Volume) mode.
Press the SOURCE button. The main menu screen appears in the display. Press the 6 (SETUP) button. The Setup mode screen is displayed. Rotate the rotary encoder and select "FM LEVEL." The Function Guide appears on the display. Press the 1 (LOW) or 2 (HIGH) button to make the signal levels between the FM band and CD/ MD player closer. Press the FUNC (RETURN) button to return to the main menu screen.

Receiving RDS Regional (Local) Stations
Press the RDS button in the FM radio mode. The display changes to the RDS setting screen. Press the 3 (AF) button to select the AF (Alternative Frequencies) ON or OFF mode. When the AF ON mode is selected, the unit automatically tunes to a strong signal station in the AF list. When the RDS station signal received has become weak in the AF seek mode, press and hold the 3 (AF) button for at least 2 seconds to have the unit automatically seek a stronger station in the AF list. Use the AF OFF mode when automatic retuning is not required.
Press the SOURCE button in the FM radio mode. The display shows the main menu screen. Press the 6 (SETUP) button. The Setup mode screen appears in the display. Rotate the rotary encoder and select "REG." The Function Guide menu is displayed. Press the 1 (OFF) or 2 (ON) button to turn off or on the REG (Regional) mode. In the REG OFF mode, the unit automatically keeps receiving the related local RDS station. Press the FUNC (RETURN) button to return to the previous screen.
Press the FUNC (RETURN) or RDS button to return to the radio mode.
NOTE To display the RDS Setting (information) screen in other mode than FM radio band, for example, press the RDS button.
Receiving Traffic Information
PTY (Programme Type) Tuning
Press the RDS button. The display changes to the RDS setting screen. Press the 4 (T.INFO) button to turn on the Traffic Information mode. Press the FUNC (RETURN) or RDS button to return to the radio mode screen. Press the 1 (g) or 3 (f) button and select the desired traffic information station. When the traffic information station is tuned in, the TP indicator lights up. Traffic information is heard only when it is being broadcast. If traffic information is not being broadcast, the unit is set in the standby mode. When a traffic information broadcast begins, the unit automatically receives it and the display shows "Traffic Info." When traffic information broadcast is over, the unit will automatically set in the standby mode.
NOTES If the traffic information broadcast signal falls below a certain level, the unit remains in the receiving mode for 1 minute. If the signal remains below a certain level for over 70 seconds, the "TP OFF" indicator appears in the display. If you do not want to listen to the traffic information being received, lightly press the 4 (T.INFO) button to skip that traffic information message. The T. INFO mode will remain in the ON position to receive the next traffic information message. If the volume level is changed while receiving traffic information, the changed volume level will be memorized. When traffic information is received next time, the volume level will be automatically adjusted to the level memorized.

Multi-Changer Selection

Alpine's Ai-NET system will support up to 6 CD Changers. When operating two or more changers, the KCA-400C (Multi-Changer Switching device) must be used. If you use 1 Switching device, you can connect up to 4 CD Changers. If you use 2 Switching devices, you can connect up to 6 CD Changers.
Press the SOURCE button to display the main menu. Rotate the rotary encoder to select "CD CHG," then press the rotary encoder. The display changes to the CD Changer mode screen. When a 6-Disc CD Changer is connected: Press the FUNC (PAGE 1/2) button. The Function Guide display changes. Press the Function buttons to select your desired disc loaded. The Function buttons 1 (DISC1) through 6 (DISC6) select the discs from the first disc to 6th disc. For example, press the 3 (DISC 3) button to select the third disc.
NOTE To select your desired track number on the selected disc, lightly press the 1 (g) or 3 (f) repeatedly until your desired track number is displayed.
Press the SOURCE button to display the main menu. Rotate the rotary encoder to select changer 1-4 (when one KCA-400C is connected) or changer 1-6 (when two KCA-400Cs are connected). Then press the rotary encoder. The display shows the selected CD Changer mode screen.
NOTE When one KCA-400C is connected to the changer, "Changer 1-4" is displayed in the main menu. When two KCA-400Cs are connected to the changer, "Changer 1-6" is displayed in the main menu.
When a 12-Disc CD Changer is connected: You can select the disc numbers 1 to 6 in the same manner as for 6-disc Changer. Press the FUNC (PAGE 1/3) button twice to select the disc numbers 7 to 12. The Function Guide display changes and now the Function buttons 1-6 represent disc numbers 7-12. Press the Function buttons (1 through 6) to select your desired disc. For example, to select 9th disc, press 3 (DISC 9) button.
In changer mode, you can select the next changer (connected changers only) by pressing the BAND button on the unit or on the remote.
NOTE You cannot operate this function in the title display or Title inputting display.
To operate the selected changer, see "CD Player Operation" section.
MD player Operation (IVX-M706 only)
(IVX-C806/CVA-1006R..optional)
SOURCE LIST Rotary encoder

Playing Mini-Disc (MD)

IVX-M706 has a built-in MD player. This section describes operation assuming that an Alpine MD player is connected. (When the MDA-5051R is connected with the IVXC806/IVX-M706/CVA-1006R, MDs can only be played back.) IVX-C806 IVX-M706 CVA-1006R built-in MD Slave MD Player Option \ Option Option
NOTE Before inserting an MD, use your finger to feel around the MD cartridge. If you feel any small bumps or irregularities, remove them because these may cause a malfunction or damage to the player.
Press the 2 (:/J) button to temporarily pause play. To resume play, press the 2 (:/J) button for a second time. Press the eject (c) button when you want to eject the MD. (If you use an optional MD player, press the eject button on the optional MD player.)

Chapter (DVD)/Track (Video CD) Sensor
Press the SOURCE button to display the main menu screen. Rotate the rotary encoder and select "DVD" from the menu. Then, press the rotary encoder to execute the selection. The display shows the DVD player mode screen. Insert a disc into the DVD/video CD/CD player, the player starts playing.
Lightly press the 1 (g) or 3 (f) button during DVD/video CD/CD play to return to the beginning of the chapter/track being currently played or advance to the beginning of the next chapter/track respectively.
NOTE The word "chapter or track" means a division of the recorded picture/sound on a DVD/video CD/CD respectively.

Fast Forward/Backward

Displaying List of Disc Titles
If titles have been memorized for Video CDs/CDs, the list of the Video CDs/CD titles can be displayed and Video CDs/CDs can be selected by their titles. (For memorizing titles, see page 41.)
Press and hold the 1 (g) or 3 (f) button during play to fast backward or forward respectively. Release the button when you reach the desired portion you wish to play. Playback starts from that portion.
Press the 4 (REPEAT) button during play to repeatedly play the chapter/track or title/disc being currently played. Each press changes the repeat play as follows: DVD: Chapter Title Repeat Off (repeat play) (repeat play) (normal play) Video CD/CD: Track Disc (repeat play) (repeat play)
NOTE The track/disc repeat modes cannot be used on video CDs with playback control (PBC). Press "MENU" to turn the PBC function off. For more details, see the operating instructions of your DVD player or DVD Changer.
Press the LIST button in the DVD/DVD Changer mode. The list of disc titles will be displayed and memorized titles will be displayed also. When DVD disc is inserted, "DVD VIDEO" will be displayed (Depending on the DVD product, "NO TITLE CD" may be displayed as well). Rotate the rotary encoder and select (highlight) your desired disc title to play. Press the rotary encoder to execute the selection. The selected title plays, the title list screen closes, and the DVD mode main screen or DVD Changer mode main screen appears.
NOTES If the disc is not titled, the display shows "NO TITLE CD." If no disc is loaded, the display shows "NO DISC." When the DVA-5205P is connected: To display the list of disc titles, switch to the DVD main screen mode and press the LIST button while playing the video CD or CD. Pressing the LIST or FUNC (RETURN) button while the list of the disc titles is being displayed, changes the display back to the DVD/DVD Changer mode screen. IVX-C806: Pressing the 2 button displays the title list or the track title list only when a CD with text is loaded in the built-in CD player. IVX-M706: Pressing the 1 button displays the title list or the MD track title list screen. CVA-1006R: When a CD/MD player or changer is connected, pressing the 1 button displays the title list.

SCAN Display It displays mode1 to mode3 repeatedly.
To deactivate the spectrum analyzer mode, press the SPE.ANA. button for at least 2 seconds.
Mode 2: This mode is suitable to vocal song music.
SOURCE INPUT Rotary encoder

INPUT Rotary encoder

Displaying Spectrum Analyzer (IVX-M706/CVA-1006R only)
Press the SOURCE button. The main menu appears in the display. Press the 6 (SETUP) button. The Setup mode screen is displayed. Rotate the rotary encoder and select "SPE. ANA." The Function Guide menu appears in the display. Press any one of the buttons 3 (MODE 1) through 5 (MODE 3), your desired mode to match the music being played. Mode 1: This mode can be used for any genre of music.
SCAN Display It displays mode 1 to mode 3 repeatedly.
To deactivate the spectrum analyzer mode, press the 1 (OFF) button.
Turning Defeat Mode On and Off
When the defeat mode is on, the sound signals bypass the BBE and surround circuits and directly go to the line output. The equalizer curve, therefore, becomes flat.
Press the SOURCE button. The main menu screen appears on the display. Press the 4 (A.PROC) button. The display shows the Audio Processor List screen. Rotate the rotary encoder and select "Defeat." The Function Guide is displayed. Press the 2 (ON) button to turn on the defeat mode. The sound signals bypass the BBE and surround circuits. To turn off the defeat mode, press the 1 (OFF) button.

Titling CDs

You can title up to 120 CDs (max.). Immediately after inputting titles or changing the settings of Initialize Mode or Display Mode (While the system is inputting the titles or data automatically) do not turn the ignition key (engine key) to OFF. Otherwise, the title may not be written, or the settings may not be changed.
NOTE The Parking Brake must be engaged to access the TITLE INPUT mode screen. Attempting to access this screen while driving will display the warning-CAN'T OPERATE WHILE DRIVING.
Activate the CD mode. Play a CD that you want to title (name). Press and hold the INPUT button for at least 2 seconds. The Title Inputting screen appears in the display. Characters are displayed at the bottom menu. Rotate the rotary encoder and select the desired character for the first position. To change between upper case, lower case, numeral and symbol, press the 3 (A/1) button. Each press changes the bottom menu. When the character for the first position has been selected, press the rotary encoder. The first character has been memorized at the first position. See "Notes" on page. Repeat steps 3 and 4 to enter the rest of characters. You can input up to 12 characters for titling one CD. When titling has been completed, press the 6 (WRITE) button to store the title in memory. The display changes to the CD mode. The input titles will be displayed when a CD titled is selected.
NOTES If the memory capacity for CD titles is full and if you attempt to title a new CD, the oldest title will be erased to make room for the new one. To delete a title, select the title you want to delete, then select "SPC" (space) and press the 6 (WRITE) button. When the 1 (; BACK) or 2 (NEXT -) button is pressed, the cursor moves to the left or right on the input titles. If an incorrect character has been entered, select "SPC" (space) and input a new character, or press the 4 (DELETE) button to delete the previous character. Press the 5 (CLEAR) button while inputting the titles to erase all the characters you have input. Pressing the FUNC (RETURN) button in the Title Input mode changes the display back to the previous display. You can title the VIDEO CD/CD while it is in DVD or DVD changer mode. The title you entered is displayed in the Disc Title List display (P. 25) (Do not operate while driving. Stop the car, then use this operation.) When the DVA-5205P is connected: To display the title input screen, switch to the DVD main screen mode and press and hold the INPUT button for at least 2 seconds while playing the video CD or CD. To display the list of disc titles, switch to the DVD main screen mode and press the LIST button while playing the video CD or CD.

Press the SOURCE button. The main menu screen appears on the display. Press the 6 (SETUP) button. The Setup mode screen appears. Rotate the rotary encoder and select "MIX LEVEL." The Function Guide is displayed. Press the 2 (DOWN) or 3 (UP) button to adjust the volume level of the navigation system's voice guidance in 7 steps. To turn off the navigation interrupt mode, press the 1 (OFF) button. Press the FUNC (RETURN) button to return to the main menu screen.
NOTES When the voice guidance of the Navigation system starts to interrupt the audio the display is automatically changed to the navigation screen. The volume level of the audio will be automatically reduced when the voice guidance of the Navigation system starts.

Setting Visual Mode

For direct access to the different visual screens, preset to the Navigation or V. SEL. You can then display the screen of the preset item by just pressing the V. SEL button on the IVX-C806/IVXM706/CVA-1006R. Immediately after inputting titles or changing the settings of Setup Mode or Display Mode (While the system is inputting the titles or data automatically) do not turn the ignition key (engine key) to OFF. Otherwise, the title may not be written, or the settings may not be changed.

Setting Bass Frequency

Press the SOURCE button. The main menu screen appears on the display. Press the 6 (SETUP) button. The Setup mode screen appears. Rotate the rotary encoder and select "VISUAL." The Function Guide is displayed. Press the 1 (NAV.) or 2 (V. SEL) to preset the desired item. When "NAVI" is preset: Pressing the V. SEL button directly switches to the navigation screen. When "V. SEL" is preset: Each press of the V. SEL button switches the modes;

NAV. AUX1 AUX2 DISPLAY

Press the SOURCE button. The main menu appears on the display. Press the 6 (SETUP) button. The Setup mode screen appears. Rotate the rotary encoder and select "BASS Cont." to activate the Bass Control mode. Press the Function button 1 (60 Hz) through 4 (100 Hz) that has the frequency you wish to control. Press the FUNC (RETURN) button. The display returns to the main menu screen.

Selecting Rear Monitor

Switching Background Textures/ Colours
You have a choice of 12 different background textures/colours preset at the factory. Select them following the procedure below. Immediately after inputting titles or changing the settings of Setup Mode or Display Mode (While the system is inputting the titles or data automatically) do not turn the ignition key (engine key) to OFF. Otherwise, the title may not be written, or the settings may not be changed.
Press the SOURCE button. The main menu appears on the display. Press the 5 (DISPLAY) button. The Display mode screen is displayed. Rotate the rotary encoder and select "DIMMER." The Function Guide is displayed. Press the 3 (AUTO) button to activate the Auto Dimmer mode. In the Auto Dimmer mode, the background illumination of the monitor is synchronized with the instrument illumination of the vehicle (the dimmer input lead should be connected). Press the 1 (OFF) button to deactivate the Auto Dimmer mode to keep the background illumination of the monitor bright. Press the 2 (ON) button to keep the background illumination of the monitor dark. When the setting has been completed, press the FUNC (RETURN) button. The display returns to the main menu screen.
Rotate the rotary encoder while the Display mode screen is displayed and select "B.GND TEXTURE" or "B.GND COLOR." The Function Guide appears on the display. Press the Function buttons (1 through 6) that has your desired texture. The Function buttons have textures/colours as follows.
B.GND TEXTURE MARBLE SKY WOOD GRAD. METAL ABYSS B.GND Colour C1 C2 C3 C4 C5 C6
The background colour changes with respect to the selected texture.
When your selection has been made, press the FUNC (RETURN) button. The display returns to the main menu screen.
Setting Automatic Background Texture/Colour Scroll
Turn on the Automatic Background Texture/colour Scroll to automatically change background texture/colours. The background texture/colour will change each time the ignition key is turned off and turned back on again (12 textures/colours). Immediately after inputting titles or changing the settings of Setup Mode or Display Mode (While the system is inputting the titles or data automatically) do not turn the ignition key (engine key) to OFF. Otherwise, the title may not be written, or the settings may not be changed.

CD (IVX-C806 only)

CD playback sound is wavering. Moisture condensation in the CD Module. - Allow enough time for the condensation to evaporate (about 1 hour). CD insertion not possible. A CD is already in the CD player. - Eject the CD and remove it. The CD is being improperly inserted. - Make sure the CD is being inserted following instructions in the CD Player Operation section. Unable to fast forward or backward the CD. The CD has been damaged. - Eject the CD and discard it; using a damaged CD in your unit can cause damage to the mechanism. CD playback sound skips due to vibration. Improper mounting of the unit. - Securely re-mount the unit. Disc is very dirty. - Clean the disc. Disc has scratches. - Change the disc. CD playback sound skips without vibration. Dirty or scratched disc. - Clean the disc; damaged disc should be replaced.

MD (IVX-M706 only)

The MD could not be inserted. Another MD is already inserted. - Eject the inserted MD and insert the MD. The MD is inserted incorrectly. - Insert the MD correctly. Sound skips due to vibration. Improper mounting. - Securely re-mount the unit. Sound skips without vibration. Dirty or scratched MD. Bad recording condition. - Change the MD. The play back wont start. Dirty or scratched MD. Bad recording condition. A non-recorded MD. Not a music MD. - Change the MD. Dew condensation. - Wait for a while before using. The power turns on but the playback wont start. The sound volume level of the head unit is adjusted to minimum. - Increase the sound volume of the head unit.
Indication for CD Player (IVX-C806 only) HI-TEMP
Protective circuit is activated due to high temperature. - The indicator will disappear when the temperature returns to within operation range.

NO DISC

No CD is inserted. - Insert a CD. Although a disc is inserted, NO DISC is displayed and the unit does not start to play or eject the disc. - Remove the disc by following these steps: 1) Press the c button. The movable display will open. 2) Press the c button again for at least 3 seconds while the movable display is open.
Mechanism error. 1) Press the c button and eject the CD. If not ejecting, consult your Alpine dealer. 2) When the error indication remains after ejecting, press the c button again. If the error indication still does not turn off after pressing the c button for a few times, consult your Alpine dealer.

NOTE When the ERROR is displayed: In case that the disc cannot be ejected by pressing the c button, press the RESET switch (refer to page 8) and press the c button again. If not ejecting, consult your Alpine dealer.
Indication for MD Player (IVX-M706 only) NO DISC
No MD is inserted. - Insert an MD.
Indication for CD Changer (Optional)

HI-TEMP

Temperature in the vehicle is too high. - Allow the vehicle's interior temperature to cool. The indicator will disappear when the temperature returns to within operation range.
No recording on disc (blank disc). - Load disc after recording. Dirty or scratched MD, bad recording, a non recorded MD, not a music MD. - Press the MD c button and change the MD. The MD is inserted incorrectly. - Press the MD c button and insert the MD correctly. Dew condensation. - Wait a while. Mechanism error.
1. Press the MD c button and eject the MD. If not ejecting, consult your Alpine dealer. 2. When the error indication remains after ejecting, press the MD c button again. If the error indication still does not turn off after pressing the MD c button for a few times, consult your Alpine dealer.

NO MAGAZINE

No CD magazine is loaded into the CD Changer. - Insert a magazine.

ERROR-01

Malfunction in the CD Changer. - Consult your Alpine dealer. Press the magazine eject button and pull out the magazine. Check the indication and insert the magazine again. If the magazine cannot be pulled out, consult your Alpine dealer. Magazine ejection not possible. - Press the magazine eject button. If the magazine does not eject, see the Owner's Manual for the CD Changer.

ERROR-02

A disc is left inside the CD Changer. - Press the EJECT button to activate the eject function. When the CD Changer finishes the eject function, insert an empty CD magazine into the CD Changer to receive the disc left inside the CD Changer.

Specifications

MONITOR SECTION
Screen Size 6.5" LCD Type Transparent type TN LCD Operation System TFT active matrix Number of Picture Elements 336,960 pcs. (1,440 234) Effective Number of Picture Elements 99.99% or more Illumination System U-shaped cold cathode fluorescent tube

If necessary, use a pinch connector to connect the parking brake lead, etc.

Vehicle Cable

Pinch Connector Pliers Monitor Cable

Stopper

Connection Diagram of SPST Switch (Sold Separately)
(If the ACC power supply is not available)
IVX-C806/IVXM706/CVA-1006R (Monitor and Tuner)

BATTERY

SPST SW (Optional)

(Yellow) Battery

NOTE If your vehicle has no ACC power supply, add an SPST (Single-Pole, Single-Throw) switch (sold separately). If the switched power (ignition) lead of the IVX-C806/IVX-M706/CVA-1006R is connected directly to the positive (+) post of the vehicles battery, the IVX-C806/IVX-M706/CVA-1006R draws some current (several hundred milliamperes) even when its switch is placed in the OFF position and the battery may be discharged.
Cautions for handling the I/F cord
The I/F cord is used to connect the monitor and the tuner BOX. Press the LOCK button gently while removing the I/F cord out of the terminal. (See the illustration below.) If you pull out the lock by force, the lock pins will be forced. This will cause a bad connection. Some possible problems:
The power of the unit turns off frequently. The display disappears. The monitor doesnt open or close.

LOCK button

Pull out the cord before you unlock the pins.
Connections (IVX-C806/IVX-M706/CVA-1006R Wiring Diagram)
To the instrument cluster illumination lead ILLUMINATION

(Orange)

IVX-C806/ IVX-M706/ CVA-1006R

<Monitor>

(Yellow)

(Black)

Antenna

FM ANTENNA

AUX2 AUX1

REMOTE OUT AUX1

<Tuner>

@ # @ # $

R AUDIO L(MONO) AUX INPUT

(White/Brown)

NAVIGATION INPUT

REMOTE OUT AUX2

R AUDIO L(MONO) AUX OUTPUT

REMOTE OUT

DISPLAY OUTPUT

Ai-NET

REMOTE TURN-ON

POWER SUPPLY FRONT

(Blue/White)
SPEAKER LEFT FRONT (White) (White/ Black)

SUB W.

POWER ANT

(Blue)

NORM EQ/DIV

AUDIO INTERRUPT IN

(Pink/Black)

PARKING BRAKE

(Yellow/Blue)

@ RGB Cable (Included with Navigation) # System Switch When connecting an equalizer or divider using AiNET feature, place this switch in the EQ/DIV position. When no device is connected, leave the switch in the NORM position. NOTE
$ RCA Extension Cable (Included with DVD video player) % Ai-NET Cable (Included with DVD video player) ^ Ai-NET Cable (Included with Equalizer) & Ai-NET Cable (Included with CD Changer) * RGB/NTSC Output Switch To display the picture of Navigation system on the external monitor, place the switch in the NTSC Output position. ( AUX Audio Input (AUX1) Terminals ) Front Output RCA Connectors Rear Output RCA Connectors RCA Extension cable (Included with DVD Changer) Ai-NET Cable (Included with DVD Changer)