PHONES (044) 360-7-130 (050) 336-0-130 (063) 788-0-130 (067) 233-0-130 (068) 282-0-130
Internet store of autogoods
ICQ 294-0-130 597-0-130 SKYPE km-130
CAR RECEIVERS Receivers Media receivers and stations Native receivers CD/DVD changers FM-modulators/USB adapters Flash memory Facia plates and adapters Antennas Accessories | CAR AUDIO Car audio speakers Amplifiers Subwoofers Processors Crossovers Headphones Accessories | TRIP COMPUTERS Universal computers Model computers Accessories | GPS NAVIGATORS Portable GPS Built-in GPS GPS modules GPS trackers Antennas for GPS navigators Accessories | VIDEO DVR TV sets and monitors Car TV tuners Cameras Videomodules Transcoders Car TV antennas Accessories | SECURITY SYSTEMS Car alarms Bike alarms Mechanical blockers Immobilizers Sensors Accessories | OPTIC AND LIGHT Xenon Bixenon Lamps LED Stroboscopes Optic and Headlights Washers Light, rain sensors Accessories | PARKTRONICS AND MIRRORS Rear parktronics Front parktronics Combined parktronics Rear-view mirrors Accessories | HEATING AND COOLING Seat heaters Mirrors heaters Screen-wipers heaters Engine heaters Auto-refrigerators Air conditioning units Accessories | TUNING Vibro-isolation Noise-isolation Tint films Accessories | ACCESSORIES Radar-detectors Handsfree, Bluetooth Windowlifters Compressors Beeps, loudspeakers Measuring instruments Cleaners Carsits Miscellaneous | MOUNTING Installation kits Upholstery Grilles Tubes Cable and wire Tools Miscellaneous | POWER Batteries Converters Start-charging equipment Capacitors Accessories | MARINE AUDIO AND ELECTRONICS Marine receivers Marine audio speakers Marine subwoofers Marine amplifiers Accessories | CAR CARE PRODUCTS Additives Washer fluid Care accessories Car polish Flavors Adhesives and sealants | LIQUID AND OIL Motor oil Transmission oil Brake fluid Antifreeze Technical lubricant
In store "130" you can find and buy almost all necessary goods for your auto in Kyiv and other cities, delivery by ground and postal services. Our experienced consultants will provide you with exhaustive information and help you to chose the very particular thing. We are waiting for you at the address

http://130.com.ua

FOR CAR USE ONLY/NUR FR AUTOMOBIL GEBRAUCH/POUR APPLICATION AUTOMOBILE UNIQUEMENT/ PARA USO EN AUTOMVILES/SOLO PER L'UTILIZZO IN AUTOMOBILE/ENDAST FR BILBRUK/

TME-M710

6.5-INCH WIDE LCD MONITOR
OWNER'S MANUAL Please read before using this equipment. BEDIENUNGSANLEITUNG Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gertes. MODE D'EMPLOI Veuillez lire avant dutiliser cet appareil. MANUAL DE OPERACIN Lalo antes de utilizar este equipo.
ISTRUZIONI PER LUSO Si prega di leggere prima di utilizzare il attrezzatura.
ANVNDARHANDLEDNING Innan du anvnder utrustningen br du lsa igenom denna anvndarhandledning.
ALPINE ELECTRONICS, INC. 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-0031, Japan Phone 03-5496-8231 ALPINE ELECTRONICS OF AMERICA, INC. 19145 Gramercy Place, Torrance, California 90501, U.S.A. Phone 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF CANADA, INC. 777 Supertest Road, Toronto, Ontario M3J 2M9, Canada Phone 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD. 161-165 Princes Highway, Hallam Victoria 3803, Australia Phone 03-8787-1200 ALPINE ELECTRONICS GmbH Frankfurter Ring 117, 80807 Mnchen, Germany Phone 089-640 ALPINE ELECTRONICS OF U.K., LTD. Fletchamstead Highway, Coventry CV4 9TW. U.K. Phone 0870-763
ALPINE ELECTRONICS FRANCE S.A.R.L. (RCS PONTOISE B 280) 98, Rue de la Belle Etoile, Z.I. Paris Nord II, B.P. 50016, 95945, Roissy Charles de Gaulle Cedex, France Phone 01-ALPINE ITALIA S.p.A. Viale C. Colombo 8, 20090 Trezzano Sul Naviglio (MI), Italy Phone 02-81 ALPINE ELECTRONICS DE ESPAA, S.A. Portal de Gamarra 36, Pabelln, Vitoria (Alava) - APDO 133, Spain Phone 945-283588
Qingdao Dongli Xinhaiyuan Printing Co., Ltd. No.17, jiushuidong road, Qingdao, China
Designed by ALPINE Japan Printed in China (S) 68-02278Z74-A
Autogood products internet store http://130.com.ua

ENGLISH

Contents

Operating Instructions

WARNING
WARNING.. 2 CAUTION... 3 PRECAUTIONS... 3

Installation and Connections
Warning... 11 Caution.. 11 Precautions.. 12 Installation.. 13 Connections.. 16

Basic Operation

Screen Display ON/OFF. 4 Adjusting the Volume... 4 Switching the Source... 4 Switching the Screen Position.. 4 Switching the display mode. 5 Adjusting.. 5

Information

In Case of Difficulty.. 9

Specifications... 10

This symbol means important instructions. Failure to heed them can result in serious injury or death.
DO NOT WATCH VIDEO WHILE DRIVING.
Watching the video may distract the driver from looking ahead of the vehicle and cause an accident.
INSTALL THE PRODUCT CORRECTLY SO THAT THE DRIVER CANNOT WATCH TV/VIDEO UNLESS THE VEHICLE IS STOPPED AND THE EMERGENCY BRAKE IS APPLIED.
It is dangerous for the driver to watch TV/Video while driving a vehicle. Installing this product incorrectly enables the driver to watch TV/Video while driving. This may cause a distraction, preventing the driver from looking ahead, thus causing an accident. The driver or other people could be severely injured.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE.
Any function that requires your prolonged attention should only be performed after coming to a complete stop. Always stop the vehicle in a safe location before performing these functions. Failure to do so may result in an accident.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISE WHILE DRIVING.
Failure to do so may result in an accident.
MINIMIZE DISPLAY VIEWING WHILE DRIVING.
Viewing the display may distract the driver from looking ahead of the vehicle and cause an accident.
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric shock.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in fire, electric shock or other injury.
KEEP SMALL OBJECTS SUCH AS BATTERY OUT OF THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If swallowed, consult a physician immediately.
USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES.
Failure to do so may result in fire or electric shock.

CAUTION

This symbol means important instructions. Failure to heed them can result in injury or material property damage.

PRECAUTIONS

Temperature
Be sure the temperature inside the vehicle is between +45C (+113F) and 0C (+32F) before turning your unit on.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Centre for repairing.

Fuse Replacement

When replacing the fuse(s), the replacement must be of the same amperage as shown on the fuse holder. If the fuse(s) blows more than once, carefully check all electrical connections for shorted circuitry. Also have your vehicles voltage regulator checked.

Maintenance

If you have problems, do not attempt to repair the unit yourself. Return it to your Alpine dealer or the nearest Alpine Service Station for servicing.

Installation Location

Make sure the TME-M710 will not be exposed to: Direct sun and heat High humidity Excessive dust Excessive vibrations After turning the system off, a slight ghost of the image will remain temporarily. This is an effect peculiar to LCD technology and is normal. Under cold temperature conditions, the screen may lose contrast temporarily. After a short warm-up period, it will return to normal.
Switching the Screen Position
If the screen is out of position when, for example, navigation system is connected to the AUX IN 1 or AUX IN 2 terminal by using the RCA extension cable, switch the screen position.
DISP POWER SELECT Main power lamp
Switch the mode to AUX1 or AUX2 to display the navigation screen. Press and hold the DISP button for at least 2 seconds. Press and hold the DISP button again for at least 2 seconds to return the position.

Screen Display ON/OFF

Press the POWER button. To turn off the POWER, press the POWER button again. If properly connected, the monitors main POWER will turn off when the vehicle's ignition switch is off. If the main power lamp illuminates in the STAND BY mode, the vehicle's battery may be discharged. After turning the system off, a slight ghost of the image will remain temporarily. This is an effect peculiar to LCD technology and is normal. Under cold temperature conditions, the screen may lose contrast temporarily. After a short warm-up period, it will return to normal.

Adjusting the Volume

Adjust the volume level by pressing the button.

Switching the Source

Press the SELECT button. Each press of the button will cycle through the modes as follows:
AUX1 AUX2 NAV. (NAVIGATION)
Switching the display mode

Adjusting

Press the DISP button. Each press of the button will cycle through the modes as follows:

Press and hold the SELECT button for at least 2 seconds. Adjustment screen will appear. Press the SELECT or DISP button and select the mode to be adjusted. or button. Adjust by pressing the SELECT : Selects the mode. (downward) DISP : Selects the mode. (upward) or : Adjusts. 1 VISUAL EQ mode (manufacturers settings) selection (VISUAL EQ MODE)

CINEMA

NORMAL
Normal images are expanded uniformly in the horizontal direction and are displayed over the entire screen.
Normal images are expanded in the horizontal and vertical directions. The top and bottom of the image are cut off. This mode is suited for 16:9 cinema size images. Normal image (4:3)

OFF NIGHT M.

: Default setting. : Suitable for movies with a lot of dark scenes. SOFT : Suitable for movies with computer graphics or animation. SHARP : Suitable for old movies whose resolution is unclear. CONTRAST : Suitable for the latest movies.
Set this function to OFF to return to the default values after changing between modes NIGHT M. and CONTRAST and adjusting the image brightness, color density and so on.
2 Brightness adjustment (BRIGHT)
Allows the brightness (15 (MIN)~+15 (MAX)) of the picture.

Continued

3 Color depth adjustment (COLOR) 7 Dimmer adjustment (DIMMER)
Change depth can be adjusted from 15 (MIN) to +15 (MAX). * Adjustment cannot be made in the NAVIGATION (RGB connection) mode. 4 Tint tone adjustment (TINT)
AUTO : Turning on/off the headlight switches the screen brightness between DIMMER HI LEVEL and DIMMER LO LEVEL. LOW : The backlighting is set to the value adjusted at DIMMER LO LEVEL. HIGH : The backlighting is set to the value adjusted at DIMMER HI LEVEL. 8 Dimmer HIGH level adjustment (DIMMER HI LEVEL)
Tint tone can be adjusted from G15 (G MAX) to R15 (R MAX). * Adjustment cannot be made in the NAVIGATION (RGB connection) mode. 5 Contrast adjustment (CONTRAST)
Contrast can be adjusted from 15 (LOW) to +15 (HIGH). 6 Screen quality adjustment (SHARP) Adjusts the LOW LEVEL (0 (MIN) to 15 (MAX)) of the dimmer. p Change sound output (SOUND OUT)
Adjusts the HIGH LEVEL (16 (MIN) to 31 (MAX)) of the dimmer.

9 Dimmer LOW level adjustment (DIMMER LO LEVEL)
Screen quality can be adjusted from 15 (SOFT) to +15 (HARD). * Adjustment cannot be made in the NAVIGATION (RGB connection) mode.
If 2 to 6 are adjusted, VISUAL EQ mode in 1 changes to CUSTOM.

MONITOR

: Outputs sound through the built-in speakers. HEADPHONE : Outputs sound to headphones if connected. * Note that sound will not be output unless the audio output settings are appropriate.
q Beep tone setting (BEEP)
After completing adjustments, press and hold the SELECT button for at least 2 seconds. The screen will return to the normal mode.
If no operation is made for 10 seconds after selecting a mode to be adjusted, the adjustment mode will be cleared.
ON : Beep tone sounds to inform you that the operation is accepted, when you press the button etc. w External input sound level adjustment (AUX IN-1 LEVEL/AUX IN-2 LEVEL)
HIGH : Sets the sound level at a high level. LOW : Reduces the sound level. e Navigation settings (NAV. IN)
When the navigation is connected to the RGB terminal, set to ON.
r Guide control setting (GUIDE CONTROL)
It is audio interruption setting for the navigation system. For European customers: Be sure to set to EUROPE. For customers in other countries: Be sure to set to STANDARD.
The setting can be made only when ON is set in e Navigation settings (NAV. IN).

Base Operation

Remote Control Sensor
Remote sensor Receives the remote control signal from connected ALPINE products such as navigation and DVD players.

In Case of Difficulty

If you encounter a problem, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer.
Navigation screen is not displayed or navigation systems remote controller keys do not work.
Navigation systems power is turned off. - Press the ON/OFF (POWER) button on the navigation systems remote controller to turn the navigation systems power on.
Screen is out of position. No function or display.
Car's ignition is off. - Turn the ignition on. No fuse or blown fuse. - Check the cause and replace the fuse. Incorrect connections. - Check connection and remedy. Vehicle's battery is weak. - Check the voltage of vehicle's battery. Navigation system is connected by using the RCA extension cable. - Press and hold the DISP button for at least 2 seconds to switch the screen position. * The fluorescent tube replacement is not free of charge even within the warranty period, for the tube is an article of consumption.

Unclear picture display.

Fluorescent tube is exhausted. - Replace the fluorescent tube*.

No picture display.

Brightness control is set for minimum brightness control. - Adjust the brightness. Incorrect setting of the VTR mode. - Switch to the correct mode. Protective circuit is on because of high temperature. - Wait until the temperature inside the vehicle comes down to the operating temperature range (45C). Incorrect or open connection with the Monitor, AV interface unit. - Check the connection and remedy.

Picture color is poor.

Brightness/Color/Tint control are not set to the proper positions. - Check each control.
Spots or dotted lines/stripes appear.
Caused by neon signs, high-voltage power lines, CB transmitter, other vehicle's ignition plugs, etc. - Change the location of your vehicle.

Unit does not operate.

Monitor's power is not turned on. - Turn on the monitor's power.

Specifications

Screen Size Display System 6.5-type Low reflection rear projection type TN liquid crystal panel Active matrix drive, Drive System normally white display Number of Picture Elements 280,800 pcs. (H:1200 x V:234 dots) Effective Number of Picture Elements 99.99% or more Light Source Internal optical system (Utype cold cathode fluorescent tube) Dimensions (W x H x D) 161 x 109 x 28.5mm Weight 270g

AV Interface Unit

Dimensions (W x H x D) Weight 130.6 x 109 x 30 mm 400g
Due to continuous product improvement, specifications and design are subject to change without notice. The LCD panel is manufactured using an extremely high precision manufacturing technology. Its effective pixel ratio is over 99.99%. This means that there is a possibility that 0.01% of the pixels could be either always ON or OFF.
Before installing or connecting the unit, please read the following and pages 2 and 3 of this manual thoroughly for proper use.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES.
When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire.

Warning

MAKE THE CORRECT CONNECTIONS.

Failure to make the proper connections may result in fire or product damage.
DO NOT INSTALL THE MONITOR NEAR THE PASSENGER SEAT AIR BAG.
If the unit is not installed correctly the air bag may not function correctly and when triggered the air bag may cause the monitor to spring upwards causing an accident and injuries.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may result in fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to electrical shorts.

Caution

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS.
The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done.
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS.
Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, shift lever, brake pedals, etc. can be extremely hazardous.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY.
Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure.
Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire etc.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wires insulation from being cut by the metal edge of the hole.

DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST.
Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR SHIFT LEVER.
Doing so may obstruct forward vision or hamper movement etc. and results in serious accident.

Precautions

Be sure to disconnect the cable from the () battery post before installing your TME-M710. This will reduce any chance of damage to the unit in case of a short-circuit. Be sure to connect the color coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage the vehicle's electrical system. When making connections to the cars electrical system, be aware of the factory installed components (e.g. on-board computer). Do not tap into these leads to provide power for this unit. When connecting the TME-M710 to the fuse box, make sure the fuse for the intended circuit of the TME-M710 has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. When in doubt, consult your ALPINE dealer. The TME-M710 uses female RCA-type jacks for connection to other units having RCA connectors. You may need an adaptor to connect other units. If so, please contact your authorized ALPINE dealer for assistance.

IMPORTANT

Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number plate is located on the rear of the monitor or on the bottom of the AV interface unit.
SERIAL NUMBER: INSTALLATION DATE: INSTALLATION TECHNICIAN: PLACE OF PURCHASE:

Installation

Installing AV Interface Unit
This Unit can be placed inside the trunk, on the kick panel of the front passenger's seat or underdash. However, to avoid unnecessary signal wiring, it is better to mount the Unit as close as possible to the Display. DO NOT MOUNT THE INTERFACE UNIT IN LOCATIONS EXPOSED TO MOISTURE OR EXTREME HEAT (such as the engine compartment). Velcro fastener Mounting: 1. Place a Velcro fastener onto the mounting surface. The rough side should be facing the unit. 2. Remove the backing to the adhesive on the Velcro strips. Press the unit onto the mounting location. Attaching with screws 1. Place the unit on the location chosen for installation. 2. Mark the screw locations using the unit as a template. 3. Drill a hole less than 3 mm in diameter.

When you are drilling a hole in the car body, be careful not to damage pipes, tanks or electrical wiring etc. It might cause an accident or a fire. 4. Firmly attach the unit using 4 of the supplied selftapping screws (M4 x 14).
Velcro fastener (included)
Self-tapping screws (M4 x 14)
Attaching the monitor and stand (for European customers only)
For customers in other countries: The stand is not included.
3 Check the sticking position.
1 Temporarily fasten the stand with gum tape. 2 Loosen the adjustment screws, and adjust to a safe, viewable position.
Do not install the monitor near the front passenger seat air bag system.
The fixed arm tilts towards the seat side.

Angle adjustment screw

1 Remove the main unit attachment fitting.
Pull this part to release.
Seat side Front glass side
Line of sight Main unit attachment fitting
2 Loosen the main unit attachment fitting with a coin
etc., slide it into the track on the rear of the main unit and temporarily fasten it. Then fix it to the stand.

Dashboard

Main unit
If the main unit invades your line of sight then it will block your view.
In order to use safely, attach to the following places. Stable and secure places. Places that will not have your view blocked by the main unit when driving. Places that you will not hit against if you lean forward while you wearing your seatbelt. Places where the main unit cannot hit against the steering wheel while driving.
Be aware that if the surface of the dashboard is leather, wooden panel, stretched fabric or any non-resin based product, then the surface will be damaged when you remove the stand. Do not place the main unit directly in front of the air conditioner vents.
Slide in an upward direction.
4 Remove the main unit from the stand. 5 Remove the mount from the stand and stick it to
the dashboard etc. Remove any dirt on the place to install, using the supplied cloth. Fixing screws (M4 x 12 Supplied)
If the place of attachment is curved, then bend this part to match the shape.
If the temperature in the car is low (Winter), then first heat up the place where you are going to stick the mount with a hairdryer etc. Do not apply force to the mount, or expose to humidity, within 24 hours after attaching. If the mount is not firmly stuck, then we recommend that you attach with the supplied fixing screws.
6 Attach the main unit to the stand as shown in step
2. Use the cable clamps to fix the cables.
Before using, check that the main unit and the stand, and the stand and the place where it is attached to the car are fixed securely.

Connections

Make connections correctly. Improper connections may cause a fire or operation failure.

Basic connection

7 o ; a s
1 Parking brake lead (Yellow/Blue) Connect this lead to the parking brake lead powered when parking brake is pulled. 2 Dimmer lead (White/Blue) This lead may be connected to the vehicles instrument cluster illumination lead. This will allow the backlighting of the unit to dim whenever the vehicles lights are turned on. 34Remote control output lead (White/Brown) To remote control input lead of ALPINE products used in the system. 5 Reverse Lead (Orange/White) Use only when a back-up camera is connected. Connect to the plus side of the cars reverse lamp that lights when the transmission is shifted into reverse (R). Switches the video picture to the back-up camera. This is linked with putting the car into reverse (R). 6 ACC power lead (Red) To ACC power lead powered when engine key position is ACC. 7 Fuse (7.5A) 8 Ground lead (Black) Connect the lead to a good chassis ground on the vehicle. Make sure the connection is made to bare metal and is securely fastened using the sheet metal screw provided. 9 p q w e r t Parking Brake Lamp Brake Connector (Included) Parking Brake Signal Lead Parking Brake Switch Headphone Main monitor Connection cable If the cable is too short, use the extension cable (KWE-664N, sold separately). RGB cable To RGB output terminal Made by Alpine navigation Audio input connectors (AUX 1) Use these connectors to input the audio signals from a DVD player, video deck etc.
To prevent external noise from entering the audio system. Locate the unit and route the leads at least 10 cm away from the car harness. Keep the battery power leads as far away from other leads as possible. Connect the ground lead securely to a bare metal spot (remove the coating if necessary) of the car chassis. If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various Alpine noise suppressors, contact them for further information. Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.

y u i o

; Video input connector (AUX 1) Use this connector to input the video signals from a DVD player, video deck etc. a Audio input connectors (AUX 2) Use these connectors to input the audio signals from a DVD player, video deck etc. s Video input connectors (AUX 2) Use this connector to input the video signals from a DVD player, video deck etc.