TUE-T112P.book Page 1 Friday, April 29, 2005 11:40 AM

TUE-T112P

MOBILE TV TUNER SYSTEM
OWNER'S MANUAL Please read before using this equipment. BEDIENUNGSANLEITUNG Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gertes. MODE D'EMPLOI Veuillez lire avant d'utiliser cet appareil. MANUAL DE OPERACIN Lalo antes de utilizar este equipo. ISTRUZIONI PER L'USO Si prega di leggere prima di utilizzare l'attrezzatura. ANVNDARHANDLEDNING Innan du anvnder utrustningen br du lsa igenom denna anvndarhandledning.
ALPINE ELECTRONICS, INC. Tokyo office: 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-8501, Japan Tel.: (03) 3494-1101 ALPINE ELECTRONICS OF AMERICA, INC. 19145 Gramercy Place, Torrance, California 90501, U.S.A. Tel.: 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF CANADA, INC. Suite 203, 7300 Warden Ave. Markham, Ontario L3R 9Z6, Canada Tel.: 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD. 6-8 Fiveways Boulevarde Keysborough, Victoria 3173, Australia Tel.: (03) 9769-0000 ALPINE ELECTRONICS GmbH Frankfurter Ring Munich, Germany Tel.: 089-640 ALPINE ITALIA S.p.A. Via C. Colombo 8, 20090 Trezzano Sul Naviglio MI, Italy Tel.: 02-81 ALPINE ELECTRONICS (BENELUX) GmbH Leuvensesteenweg 510-B6, 1930 Zaventem, Belgium Tel.: 02-725 1315
ALPINE ELECTRONICS FRANCE S.A.R.L. (RCS PONTOISE B 280) 98, Rue De La Belle Etoile, Z.I. Paris Nord Il B.P. 50016 F-95945, Roissy, Charles De Gaulle Cedex, France Tel.: 01-ALPINE ELECTRONICS OF U.K., LTD. 13 Tanners Drive, Blakelands, Milton Keynes MK14 5BU, U.K. Tel.: 01908-56 ALPINE ELECTRONICS DE ESPAA, S.A. Portal De Gamarra 36, Pabelln Vitoria (Alava)-Apdo. 133, Spain Tel.: 34-45-283588

Contents

Operating instructions

WARNING

WARNING... 2 CAUTION.. 2 PRECAUTIONS.. 3
Installation instructions
Installation and Connections
WARNING.. 16 CAUTION.. 16 PRECAUTIONS. 17 Before installing. 17 Installing the antenna.. 20

Controls and Features

TV tuner unit.. 4 Remote controller. 5 Remote Controller Battery Replacement.. 6

Electrical Connections

Typical Connections. 21

Troubleshooting

Basic Operations
Watching television.. 7 Storing channels in memory (auto memory).. 8 Setting the channel selection. 9 Watching playback of external component.. 10 Adjusting the headphone volume.. 11

Maintenance Information

In Case of Difficulty. 13 Specifications.. 14
TUE-T112P.book Page 2 Friday, April 29, 2005 11:40 AM

WARNING CAUTION

This symbol means important instructions. Failure to heed them can result in serious injury or death.

CAUTION

This symbol means important instructions. Failure to heed them can result in injury or material property damage.
BE SURE TO INSTALL THE MONITOR ON TOP OF THE DASHBOARD TO PREVENT IT FROM OBSTRUCTING VISIBILITY. Any function that requires your prolonged attention should only be performed after coming to a complete stop. Always stop the vehicle in a safe location before performing these functions. Failure to do so may result in an accident. DO NOT DISASSEMBLE OR ALTER. Doing so may result in an accident, fire or electric shock. USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS. Use for other than its designed application may result in fire, electric shock or other injury. KEEP SMALL OBJECTS SUCH AS BATTERY OUT OF THE REACH OF CHILDREN. Swallowing them may result in serious injury. If swallowed, consult a physician immediately. USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may result in fire or electric shock.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Center for repairing. DO NOT MIX NEW BATTERIES WITH OLD BATTERIES. INSERT WITH THE CORRECT BATTERY POLARITY. When inserting the batteries, be sure to observe proper polarity (+ and -) as instructed. Rupture or chemical leakage from the battery may cause fire or personal injury.
TUE-T112P.book Page 3 Friday, April 29, 2005 11:40 AM

PRECAUTIONS

Temperature Be sure the temperature inside the vehicle is between +45C (+113F) and 0C (+32F) before turning your unit on. Fuse Replacement When replacing the fuse(s), the replacement must be of the same amperage as shown on the fuse holder. If the fuse(s) blows more than once, carefully check all electrical connections for shorted circuitry. Also have your vehicle's voltage regulator checked. Maintenance If you have problems, do not attempt to repair the unit yourself. Return it to your Alpine dealer or the nearest Alpine Service Station for servicing. Installation Location Make sure the TUE-T112P will not be exposed to:

Direct sun and heat High humidity Excessive dust Excessive vibrations
TUE-T112P.book Page 4 Friday, April 29, 2005 11:40 AM

TV tuner unit

ANTENNA INPUT jacks (for connecting the diversity antenna) INPUT 2 jacks VIDEO AUDIO L AUDIO R
OUTPUT jacks VIDEO AUDIO L AUDIO R

HEADPHONE jack

INPUT 1 jacks VIDEO AUDIO L AUDIO R
POWER SUPPLY connector REMOTE EYE INPUT
TUE-T112P.book Page 5 Friday, April 29, 2005 11:40 AM

Remote controller

POWER button (7) VOL UP (Headphone volume up) button (11) VOL DN (Headphone volume down) button (11) SEEK button (9) A.MEMO (Auto memory) button (8) TV/AV button (7, 8, 9, 10) CH UP (Channel up) button (7) CH DN (Channel down) button (7) CH CALL button (10)
Before using the remote controller: Aim the remote controller directly at the remote sensor on the color monitor. Make sure there is no obstacle in between. Do not expose the remote sensor to strong light (direct sunlight or artificial lighting).

F G H I

TUE-T112P.book Page 6 Friday, April 29, 2005 11:40 AM
Remote Controller Battery Replacement
Battery type: CR2025 battery or equivalent.
Closing the cover Slide the cover as illustrated until a click is heard.
Opening the battery case Slide out the battery cover while firmly pressing in the direction of the arrow.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE. Any function that requires your prolonged attention should only be performed after coming to a complete stop. Always stop the vehicle in a safe location before performing these functions. Failure to do so may result in an accident.
Replacing the battery Put the battery in the case with the (+) indication upward as shown in the illustration.
Placing a battery in backwards way may cause a malfunction.
TUE-T112P.book Page 7 Friday, April 29, 2005 11:40 AM

Watching television

Preparation Before operating the system, make sure that all external components are correctly connected and installed. For connecting the external components, refer to the instructions and the installations supplied with the external components.

Select TV as the input source. Press the TV/AV button on the remote controller repeatedly to select TV. Select the channel you want to watch. Press the CH UP or CH DN on the remote controller to change the channels. If the channel selection is set to AUTO (See page 9.) You can select only the channels preset by the auto memory function. (See page 8.) If the channel selection is set to MANUAL (See page 9.) You can select all the channels. (Channel coverage: VHF channels 1 to 12, UHF channels 21 to 69)
Adjust the volume level on the car receiver.
If the system is connected to the parking brake system: Engage the parking brake and turn on the engine. If the system is not connected to the parking brake system: Turn on the engine. Turn on the power. Press the POWER button on the remote controller.
To turn off the power Press the POWER button on the remote controller. Turning off the engine will also turn off the TV tuner system.
TUE-T112P.book Page 8 Friday, April 29, 2005 11:40 AM
Storing channels in memory (auto memory)
The auto memory function picks up the TV broadcast signals in the area where you are and stores them automatically in memory.
When scanning is over, the screen shows the TV program of the smallest channel number in memory. NOTES
TV stations with weak signals are not be picked up, therefore not being stored in memory. If you drive from one broadcasting area to another, the stored channels will not be tuned in. In this case, perform the auto memory function again to store the stations in another area.
Select TV as the input source. Press the TV/AV button on the remote controller repeatedly to select TV. Start scanning TV broadcast signals. Press the A.MEMO button on the remote controller. The auto memory function starts and TV broadcast signals are picked up and stored in memory while scanning.
TUE-T112P.book Page 9 Friday, April 29, 2005 11:40 AM
Setting the channel selection
You can set the channel selection method either to select only the receivable channels in memory or to select all the channels. Remember that if you want to select only the receivable channels, you must store the channels first. To store them, see page 8.

Only the receivable channels stored in memory can be selected. When you change the channel, channel number and AUTO appear on the screen for a while.
MANUAL: All the channels can be selected. (Channel coverage: VHF channels 1 to 12, UHF channels 21 to 69)
Select TV as the input source. Press the TV/AV button on the remote controller repeatedly to select TV. Set the channel selection to AUTO or MANUAL. Press the SEEK button on the remote controller. Each time you press the button, the channel selection alternates between AUTO and MANUAL.
TUE-T112P.book Page 10 Friday, April 29, 2005 11:40 AM
Watching playback of external component
You can connect up to 2 external video components to the TV tuner unit. To watch the playback, first follow steps 1 and 2 on page 7, then perform the following steps.
Ex: When AUX1 is selected
Play back the external component. To operate the external components, refer to the manuals of the connected components. Adjust the volume level on the car receiver.
To check the current input source Press the CH CALL button on the remote controller. The current input source name appears on the screen for 3 seconds.
To turn off the power Press the POWER button on the remote controller. Turning off the engine will also turn off the TV tuner system. NOTES
When you watch the screen aslant, the picture might not be clear. This is not a malfunction. The finest picture can be seen when you watch the screen straight.
Select the input source. Press the TV/AV button on the remote controller to select the input source you want. Each time you press the button, the input source changes as follows:

TV AUX1 AUX2

The selected input source name also appears on the screen for 3 seconds.
TUE-T112P.book Page 11 Friday, April 29, 2005 11:40 AM
Adjusting the headphone volume
Press and hold the VOL UP or VOL DN button to adjust the headphone volume. You can adjust the volume level between 0 and 35.

VOL DN and VOL UP

The headphone volume level appears on the screen. NOTE
This adjustment is only for the connected headphones but not for the speakers in the car. When adjusting the speaker volume, adjust it by using the car receiver.
TUE-T112P.book Page 12 Friday, April 29, 2005 11:40 AM

Maintenance

To prevent damage to the system exterior Do not apply pesticides, benzine, thinner or other volatile substances to the unit. The cabinet surface primarily consists of plastic materials. Do not wipe with benzine, thinner or similar substances because this will result in discoloration or removal of the paint. When a cloth with a cleansing chemical is used, follow the caution points: - Do not leave the unit in contact with rubber or vinyl products for long periods of time. - Do not use cleansers which have polishing granules because this could damage the surface of the unit. Clean dirt by wiping lightly with a soft cloth When the unit is very dirty, wipe with a well-wrung cloth dipped in a kitchen cleanser (neutral) thinned by water and then go over the same surface with a dry cloth. (Since there is the possibility of water drops getting inside of the unit, do not directly apply cleanser to the surface.)

If water drops or similar wet substances get inside of the monitor via the liquid crystal panel surface, it may cause a malfunction.
TUE-T112P.book Page 13 Friday, April 29, 2005 11:40 AM

Information

In Case of Difficulty
If you encounter a problem, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer. No power supplied.
Vehicle's ignition is off. - Turn the ignition on. No fuse or blown fuse. - Check the cause and replace the fuse. Incorrect connections. - Check connection and remedy. Vehicle's battery is weak. - Check the voltage of vehicle's battery.
Picture not clear or noises appear.
Poor signal strength. Out of service area of station being received. - Check by moving car in other location. Fluorescent tube is exhausted. - Replace the fluorescent tube.*

No picture obtained.

Mode switch is not set to a desired mode. - Select desired mode by pressing TV/NAV./ VIDEO button. Temperature inside car is high. - Lower the temperature. Poor connections between monitor and tuner. - Check connections.
Dots or stripes appear on picture.
Affected from neon sign, high voltage line, amateur radio transmission, cars, etc. - Move car to a location free from interference.
Remote control does not work.
Battery is worn out. - Replace battery. Incorrect battery insertion. - Insert battery correctly. Remote control does not point remote control sensor. - Operate remote control so that it faces the sensor. Remote control sensor or remote control transmitter window is dirty. - Clean remote control sensor or transmitter window.
Double or triple pictures or rolling picture appear.
Signals are reflected by mountain or buildings near car. - Move car to other locations. Adjust location, direction and height of antenna.
Noises appear in car radio.
High frequency signals from TV are received by car radio. - Keep away antenna leads and other wire leads from TV.
TUE-T112P.book Page 14 Friday, April 29, 2005 11:40 AM
Too much voice noise is heard.
TV area is improper. - Confirm the setting for a TV area.

Specifications

TV TUNER UNIT Input Antenna:. Mini-jack 4 Video:.. RCA pin 2 circuits 1 V(p-p), 75 Audio:.. RCA pin 2 circuits 0.5 V(rms) Remote in:..Stereo mini-jack 1 Output
Audio interruption function does not work in combination with navigation system.
TV channel 56 is received. - Switch channel other than 56. Poor connection of guide control input cord. - Connect guide control cord of navigation securely.
Channel display is incorrect.
The field strength is low. - Move the car to other location and check it again.

Picture becomes whitish.

Located under a TV tower. - Move the car to other location to use it. - If you want to use in that location, turn the TV antenna's booster switch to off position. * The fluorescent tube replacement is not free of charge even within the warranty period, for the tube is an article of consumption.
Video:.RCA pin 1 circuit 1 V(p-p), 75 Audio:.RCA pin 1 circuit 0.5 V(rms) Headphone:.Stereo mini-jack mW to 15 mW per channel output into 32 Dimensions (W H D):.. 163 mm 28.5 mm 120 mm Mass:..0.6 kg GENERAL Channel coverage:..VHF: ch UHF: ch Power Requirement Operating Voltage:.. DC 14.4 V (11 V to 16 V allowance) Grounding System:. Negative ground Allowable Operating Temperature:.. 0C to +40C Allowable Storage Temperature:.. 20C to +80C Design and specifications subject to change without notice.
TV/AV button does not work well.
Even if pressing the TV/AV button, TV area setup menu screen does not come out. - Press the button after changing TV band to TV1 or TV2. It cannot be operated if it is TV3.
TV area cannot be changed.
Even if trying to change the TV area, it stays to be the former one. - Change the TV area again, and press and hold the TV/AV button at least 1 second.
TUE-T112P.book Page 15 Friday, April 29, 2005 11:40 AM
DIVERSITY ANTENNA Output impedance.. 75 ohms, 3.5 mini-jack Operating Voltage..DC14.4V (11 to 16V) Operating Current..50mA Operating Temperature Range..10C ~ +60C
TUE-T112P.book Page 16 Friday, April 29, 2005 11:40 AM
Before installing or connecting the unit, please read the following and pages 2 and 3 of this manual thoroughly for proper use.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION, SUCH AS THE STEERING WHEEL OR GEARSHIFT. Doing so may obstruct forward vision or hamper movement etc. and results in serious accidents.
MAKE THE CORRECT CONNECTIONS. Failure to make the proper connections may result in fire or product damage. USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND. (Check with your dealer if you are not sure.) Failure to do so may result in fire, etc. BEFORE WIRING, DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL. Failure to do so may result in electric shock or injury due to electrical shorts. DO NOT SPLICE INTO ELECTRICAL CABLES. Never cut away cable insulation to supply power to other equipment. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock. DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installation or ground connections. Using such parts could disable control of the vehicle and cause fire, etc. KEEP SMALL OBJECTS SUCH AS BATTERY OUT OF THE REACH OF CHILDREN. Swallowing them may result in serious injury. If swallowed, consult a physician immediately.

HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit requires special technical skill and experience. To ensure safety, always contact the dealer where you purchased this product to have the work done. USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure. ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE. Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wires insulation from being cut by the metal edge of the hole. DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST. Avoid installing the unit in locations with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product failure.
TUE-T112P.book Page 17 Friday, April 29, 2005 11:40 AM
Be sure to disconnect the cable from the () battery post before installing your TUE-T112P. This will reduce any chance of damage to the unit in case of a shortcircuit. Be sure to connect the color coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage the vehicle's electrical system. When making connections to the cars electrical system, be aware of the factory installed components (e.g. on-board computer). Do not tap into these leads to provide power for this unit. When connecting the TUE-T112P to the fuse box, make sure the fuse for the intended circuit of the TUE-T112P has the appropriate amperage. Failure to do so may result in damage to the unit and/or the vehicle. When in doubt, consult your ALPINE dealer. The TUE-T112P uses female RCA-type jacks for connection to other units (e.g. amplifier) having RCA connectors. You may need an adaptor to connect other units. If so, please contact your authorized ALPINE dealer for assistance.

Before installing

The diversity antenna supplied with this unit is designed specifically for use with the ALPINE mobile color monitor system. (It cannot be connected to the car radio.) Do not rub the antenna or the antennas cable with alcohol, benzine, thinner, gasoline or other volatile substances. Attach to the inside of the car window glass. Be sure to wipe the window surface where the antenna will be attached with a clean cloth to remove moisture, dirt, dust, wax, oil or other substances. (If there is moisture, oil or other wet substances on the attachment surface, the attachment tape will not stick well and easily come off.) Be sure to attach the antenna so that the adhesive surface is not on glass heating wires or glass antenna wires. Identify the exact attachment location and confirm that the antenna will not interfere with a heating wire, glass antenna or wiper motor.

IMPORTANT

Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number plate is located on the bottom of the unit. SERIAL NUMBER: ___________________ INSTALLATION DATE: __________________ INSTALLATION TECHNICIAN: __________ PLACE OF PURCHASE: _______________
TUE-T112P.book Page 18 Friday, April 29, 2005 11:40 AM

Antenna element

Loading section
Ground wire Connected to metal section on the vehicle
Antenna base Ground wire Connected to metal section on the vehicle

Headphone (not supplied)

Monitor, etc.

1 HEADPHONE

R AUDIO L OUTPUT

Remote EYE INPUT

POWER SUPPLY

ANTENNA INPUT VIDEO

INPUT 2 L AUDIO R VIDEO

INPUT 1 L AUDIO R

DVD Player, etc.
TUE-T112P.book Page 19 Friday, April 29, 2005 11:40 AM
When the attachment surface overlaps with a heating wire or glass antenna a For the antenna base Attach the antenna base to the location where it does not overlap with a heating wire or glass antenna.
Antenna base Take off the adhesive tape
Antenna elements end Take off the adhesive tape
When the attachment surface overlaps with an electrode Attach the antenna to either the left or right of the electrode.

Electrode

For the loading section Attach the loading section to the location where it does not overlap with a heating wire or glass antenna.
Loading section Take off the adhesive tape

Heating wires

When the attachment surface interferes with a rear wiper motor or a high-mounted brake light Move the antennas attachment position upwards to avoid interference.

For the antenna elements end Attach the antenna elements end to the location where it does not overlap with a heating wire or glass antenna.
TUE-T112P.book Page 20 Friday, April 29, 2005 11:40 AM

Installing the antenna

Remove the cover paper from the antenna base tape and attach to the surface. Remove the cover paper from the loading section tape and attach to the surface. Remove the cover paper from the antenna elements end tape and attach to the surface.
Antenna elements end Loading section

Antenna base

TUE-T112P.book Page 21 Friday, April 29, 2005 11:40 AM
To prevent short circuits, we recommend that you disconnect the batterys negative terminal and make all electrical connections before installing the unit. If you are not sure how to install this unit correctly, have it installed by a qualified technician. NOTE
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at ALPINE IN-CAR ENTERTAINMENT. Replace the fuse with one of the specified ratings. If the fuse blows frequently, consult your ALPINE IN-CAR ENTERTAINMENT.

Typical Connections

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
Connect the colored leads of the power cord to the car battery, remote control and parking brake in the following sequence. 1 Black: ground 2 Yellow: to car battery (constant 12 V) 3 Red: to an accessory terminal 4 White with brown stripe: to remote control lead of monitor 5 Yellow with blue stripe: to parking brake or metallic body or chassis of the car
Finally connect the wiring harness to the unit.
TUE-T112P.book Page 22 Friday, April 29, 2005 11:40 AM
*1: Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be turned on.

Ignition switch

To metallic body or chassis of the car
* * Not included with this unit *

Yellow*1

To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch)
To an accessory terminal in the fuse block

Fuse block

White with brown stripe
To remote control lead of monitor

Yellow with blue stripe

To parking brake or metallic body or chassis of the car
TUE-T112P.book Page 23 Friday, April 29, 2005 11:40 AM

The fuse blows.

Are the yellow and black leads connected correctly?
Power cannot be turned on.
Is the red lead connected?
Picture does not come on screen.
Is the parking brake engaged? Is the yellow, blue striped cord correctly connected?

Picture does not appear clearly.
Is the color monitor installed at the right angle?

SC ALAMSERVICE 96 SRL

MS-VW02

www.alarmservice.ro

Contents:
Contents.... 2 Safety instructions..... 3 Service / communication... 4 Shipment..... 4 Product description.... 5 Installation of cable kit MS-VW02 with VW Touareg and T5.. 5-6 Installation of cable kit MS-VW02 with VW Golf 5, Touran, Passat.. 7 Installation of cable kit MS-VW02 with Maserati Quattroporte.. 8 Function and Controls.... 9-11 Button Assignment for MFD2 System... 11 Button Assignment for Maserati Quattroporte... 12

Safety instructions:

1. Read through mounting guidelines: Please read through all safety instructions and handling directions intently before installation and start up of the device. 2. Keep mounting guidelines: Keep the instruction manual and safety instructions for potential further reference. 3. Caution advises: Please follow all caution advises contained in the mounting guidelines. 4. Water and humidity: The device should not be operated near water or near a humidity source. 5. Warmness / heat: The device should not be set up in direct proximity of heat sources (e. g. power amplifier). 6. Electric power supply: The device should only be operated at a +12 volt vehicle electrical system. 7. Connection / electric power supply: Use the device only at a +12 volt vehicle electrical system. Make sure to have a proper ground. 8. Intrusion of objects or liquids: Please make sure that no objects or liquids can intrude the interior of the device! (Danger of short circuit!) 9. Repairs: You should call on qualified personnel, if: a plug or a connector have been damaged cables are damaged objects have fallen into the device or liquids have intruded it the product has been exposed to humidity the device doesn't function normally or if significant changes in the operating performance can be observed the product/casing has been damaged. 10. Operation: Start no operation that is likely to distract you for a prolonged time from road traffic or traffic related events RISK OF ACCIDENT!!! 11. Warranty: The warranty will cease in case that: you open the device or the casing you carry out repairs single handed you use the device improperly the device shows damages caused by external forces or mischievous destructions.
We assume no liability for damages to the vehicle or to people.

Product description:

Article: Function: MS-VW02
Cable kit for Multimedia Interface MULTI01/MULTI03 for use in conjunction with the following systems: VW with MFD2 system: Golf5, Passat, Touran Touareg, T5 SKODA with Nexus system: Octavia II Maserati: Quattroporte
Connection assignment of the cable kit:
Wire Colors/Plugs: 18pin AMP-connector: Red: Black: Yellow: Blue: 3,5mm Jack Socket: Cinch-Plug Red: Cinch-Plug Black: Connection/Assignment: Connect to MFD2 / RNS2 +12V DC GND CAN-HI CAN-LOW Controls AUDIO-Input (right) AUDIO-Input (left)
Installation of Cable Kit:
Instructions for VW Touareg and T5 with MFD2/RNS2:
Warning: Do not install interface while ignition is turned on.
1. Extracting the navigation system from the center console requires the use of a brand-specific de-locking tool (sold separately).
2. Disconnect the Quadlock-connector from the navigation system. Connect the 18pin AMP connector of the cable kit to the navigation system.
3. Connect the corresponding control cable (e.g. STK-AL25 for DVD Alpine devices) to the jack socket. Additionally, the available Y-adapter CABLE-415 (sold separately) may be used to enable the connection of the IR-remote receiver of a video source parallel to the interface itself. Connect this adapter between the jack socket of the cable kit and the corresponding control cable. A Video / Audio Cinch cable (sold separately) is needed to connect the video source to the three Cinch sockets of the interface.
4. Connect the blue wire of the cable kit to the Quadlockconnector at Pin10 (CAN LOW) and connect the yellow wire at Pin9 (CAN HI). Connect the black wire at Pin12(ground). Connect the red wire at Pin15(permanent plus). (See schematic on the right)
5. Reconnect the Quadlock-connector to the navigation system and re-attach it to the center console.
Instructions for VW Golf 5, Touran, Passat with MFD2/RNS2:
1. Carefully remove decorational covers around navigation system. Loosen the 4 TORX-screws indicated in the picture on the right and extract the device from the center console.
Instructions for Maserati Quattroporte:
1. Carefully detach the decorational cover from the center console by first extracting the clipped upper ventilation unit and loosening the two screws located behind it. The clipped lower cover of the center console needs to be removed next. Now loosen the lower two screws of the decorational cover and carefully take out the whole construct. (Caution: The navigation system is attached to the decorational cover!)

2. Disconnect the Quadlock-connector from the navigation system. Connect the 18pin AMP connector of the cable kit to the navigation system
4. Connect the blue wire of the cable kit to the Quadlockconnector at Pin10 (CAN LOW) and connect the yellow wire at Pin4 (CAN HI) (in each case chamber B). Connect the black wire at Pin12(ground). Connect the red wire at Pin15(permanent plus).

Function and Controls:

Activation (VW, koda): Pushing the Aux (MFD2 CD Version) button followed by the TV button or pushing the CD (MFD2 DVD Version) button followed by the AUX button activates the AV-input.
Device Assignment (VW, koda): Pushing soft key button 1 (see on page 11) for a prolonged time brings up TV1 RC01 on the instrument clusters display. Input of device-specific control codes is achieved by turning the right knob. (For details concerning control codes see chart below)
Pushing the right knob displays TV2 RC1. Enter the second device-specific code on this level. Pushing the knob again exits the input level and saves the entered codes.

Device RC Codes:

Model DVD USB, MP410, MP412, AD212U, DVP-1000M, DVP900HD DVBT2007, Dietz 1491/V AMPIRE DVB-T100 DVB2008, TRT400 DVDC CKO DVC10 DVD-Changer CKO- DVC 6M , Yamakawa DVD-Changer DVBT NL, SENERGY, C-KO DVBT-1080, Axion DVBT 500 DVD ADJQ-DVDRD, PYLE PLTD24, Veba, Carmedien CM06 DVD 1/2 DIN (NO NAME) DVD Alpine RUE - 4201 DVD Alpine RUE - 4158;TUE-T150DV DVBT Eastern SE863-T iPod Vlink DVBT ZENEC ZE-DVBT25 V-HUB VPA-B222R Alpine Radio V-HUB VPA-B222R Alpine DVD DVD Necvox DVA-3206 Analog-TV Alpine TUE-T112P Analog-TV TRT-003 BOA-DVD 85700 /AIV, C-KO 412 DVD Visteon VXM2200 RC Code: 21 Model DVBT Quantum QTM10 DVD Elite ELT-900XU Novosonic DVDC CkO MPC6 DVD-TIXXON (No Name) HD-Player 3,5 MVIX MV-5000U DVD Axion VDV-402 DVD Bullit CDVD12 DVD ZENEC ZE-080 DVBT Ampire DVBT200 DVBT&DVD USB Digitaldynamic Multiplayer iPod Alpine KCE-425I A-TV TVT-765 Emperor Mini DVBT DVBT Carmedien DVB423 DVBT M-DTV-201-0 DVDC Pioneer XDV-P6 (Reserviert) DVD Phonocar VM 015 (USB/SD) Hirschmann DVBT / Visteon DVBT HD Microlab - Pocket X Div 25 (2,5 Zoll HD P. Tixxon) DVB-T D80 DAS / Dietz 1492 DVB-T DVBT Ampire DVBT50 RC Code: 42 43
Activation (Maserati): Pushing the TV button activates the AV-input of the system.
Device Assignment (Maserati): Due to the missing display connectivity in conjunction with Maserati Quattroporte navigation systems, settings cannot be adjusted with visual control. To input the RC code upon first activation of the interfaces, first push the TV button, then turn the right-hand side knob clockwise to select the devicespecific control codes. Starting point is always RC Code 01. Pushing the knob exits the input level and saves the entered codes. (For details concerning control codes see chart below) Device RC Codes:

Controls: The video source(s) are controlled using various MDF2/RNS2 buttons. Pushing the upper right knob for a prolonged time switches between device controls (only VW, koda). For a detailed button assignment see chart below.
Button Assignment for MFD 2:
Button Assignment Part 1 MFD 2 / RNS2
DVD / DVDC DVB-T TUNER I-POD CONTROL ANALOG TUNER
PLAY PLAY/PAUSE PLAY/PAUSE SCAN

1 (3sec)

RC CODE RC CODE RC CODE RC CODE

AV AV EJECT MODE

PBC EPG SHUFFLE FM
TITLE INFO REPEAT DISPLAY

ZOOM/DISC SCAN SCAN

SETUP MENU BULB ADJUST

DISPLAY DISPLAY DISPLAY

AUDIO AUDIO AUDIO
Button Assignment Part 2 MFD 2 / RNS2

STOP EXIT PLAY MUTE

11 (3sec)
SETTINGS MENU SETTINGS MENU SETTINGS MENU SETTINGS MENU

VOL -

VOL +

ENTER OK ENTER MODE

14 (3sec)
SWITCH AV1/AV2 SWITCH AV1/AV2 SWITCH AV1/AV2 SWITCH AV1/AV2

TRACK CH TRACK CH -

TRACK + CH + TRACK + CH +
4:3/16:9 4:3/16:9 4:3/16:9 4:3/16:9
Button Assignment for Maserati Quattroporte:
Button Assignment Maserati Quattroporte
DVD PLAYER DVB-T TUNER I-POD CONTROL ANALOG TUNER

TRACKCH TRACKCH -

TRACK+ CH + TRACK+ CH +

CH -

SETUP MENU LIGHT ADJUST

CH +

VOL+

VOL-

We wish you a lot of fun with your new device and thank you for deciding in favor of our product.