3. Power source Use only power supplies of the type specified in the operating instructions or 1 as marked on the appliance. If a separate power supply is included with this apparatus, do not substitute with any other power supply use only manufacturer-provided power supplies. 4. Unplug this apparatus during lightning storms or when unused for long periods of time. 1 5. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been 1 damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. For service, refer to qualified service personnel, return to the dealer, or call the Altec Lansing service line for assistance. 6. For products that incorporate batteries, please refer to local regulations for proper battery disposal. 1 7. Only use attachments/accessories specified by the manufacturer. 1 8. 1 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
1. Protect the power cord from being walked on or pinched particularly at plugs, convenience 1 receptacles, and the point where they exit from the apparatus. 2. Do not install in an area that impedes the access to the power plug. Disconnecting the power plug is 1 the only way to completely remove power to the product and must be readily accessible at all times.

Contents

Welcome...... ii. Safety Information...... 1 Package Contents...... 3 Getting Started...... 4 Placing and Removing Adapters for the iPod..... 5 Speaker Features and Indicators..... 6 Speaker Controls..... 7. Enhanced Remote Features...... 9 Wireless Snooze Remote Features..... 11 Listening to Your iPod...... 12 Charging your iPod..... 13. Listening to the FM Radio..... 13 Listening to a Non-docking iPod or Other Portable Audio Device... 14. Mood Light...... 15 Setting the Clock Display...... 16 Setting the Alarm...... 18. Setting the Sleep Timer...... 20 Maintaining Your Speaker System..... 20 Troubleshooting...... 21. Warranty...... 24

Package Contents

Altec Lansing Moondance Glow speaker system

User Guide and Quick Connect Instructions Enhanced remote
Miscellaneous adapters for iPod

FM radio antenna

Wireless snooze remote

Snooze remote receiver

Power supply

Getting Started

How to Install the Backup Battery This Altec Lansing Moondance Glow speaker system uses a backup battery system to provide continuous clock settings in the event of a power failure. With the backup battery (not included) installed, if a power failure occurs or the AC cord is accidentally disconnected, the display will not remain lit and the alarm will not function, but the current time will be temporarily maintained. Otherwise, you must reset the time and alarm settings. How to Install the AC Adapter
Connect the AC adapter cable plug into the speaker systems jack. The jack is located on the back of the system.
Make sure the AC adapter is connected. Your settings may be lost during battery installation if the AC adapter isnt connected.
Plug the AC adapter into the wall outlet.
How to Install the Enhanced Remote Battery The enhanced remote battery (included) is not installed at the factory. To install the battery, follow the steps below:
Open the battery compartment cover. The compartment cover is located on the bottom of the system.
Pull out the battery holder. The battery door is located on the lower end of the remote. Simply pull the tab to open the battery holder.
Insert one 9-volt battery (not included). Be sure to check that the polarity (+ and ends of the batteries) matches the illustration inside the battery compartment. Altec Lansing recommends the use of alkaline batteries for longer life.
Position the battery (included) so it sits in the battery holder correctly. Make sure the polarity (the + and sides of the battery) is correct. Replace the battery door.
Close the battery compartment cover.
NOTE Please discard used batteries properly.
Placing and Removing Adapters for the iPod
Your Altec Lansing Moondance Glow speaker system includes removable adapters for todays popular iPod models. These adapters ensure that your iPod properly fits in the speaker systems dock. As new iPod models are introduced, new adapters will be made available to customers. You may also use the adapters supplied with your iPod or available for purchase at www.apple.com. How to Place an Adapter
Select the correct adapter for your iPod. Using the correct adapter ensures a proper fit for your iPod.

Gently press the iPod adapter into the dock. Now you can carefully place your iPod into the dock.
NOTE Your iPod cannot be in a case or a skin. How to Remove an Adapter
Remove your iPod. Grip the adapter and pull gently upward.
Speaker Features and Indicators
Alarm 2 button Alarm 1 button Track forward button Track back button Volume increase button Play/snooze/pause button Volume decrease button Mood light button Source button Power on/off button Snooze remote jack Clock button

LCD display

AUX jack AC adapter jack Battery compartment FM antenna Universal docking station for iPod

Speaker Controls

Turn on your speaker system Ensure the AC adapter is connected to the system and plugged into the wall. See the Getting Started section for more information. Press the button. Press the button. Whenever you are finished using your speaker system, please remember to turn it and your iPod or other MP3 player off to conserve electricity. Press the button to cycle through and select the audio source: iPod, FM radio or AUX. button. See the Listening to Your iPod section for more
Turn off your speaker system Change audio source Play a track from your iPod Pause your iPod Turn up the volume Turn down the volume Skip to the beginning of the current song on your iPod
In iPod mode, press the information. In iPod mode, Press the Press the + button. Press the button. In iPod mode, press the button.

button.

Rewind the currently playing track on your iPod In iPod mode, press and hold the Skip to the beginning of the next song on youriPod Fast-forward the currently playing track on your iPod Tune radio stations In iPod mode, press the button.
In iPod mode, press and hold the In FM mode, use the and
buttons. See the Listening to the Radio section for additional information.
Scan radio stations In FM mode, press and hold the information. or button. See the Listening to the Radio section for additional
Listen to a non-docking iPod or MP3 player Turn on the mood light Set the clock Set the alarm Dismiss the alarm Snooze for 5 to 60 minutes (user-definable) Reset all settings Select FM Band region
See the Listening to a Non-docking iPod or Other Portable Audio Device section for specific information on using devices attached to your speaker systems AUX jack. Press the button. See the Mood Light section for more information.

See the Setting the Clock Display section for detailed instructions on setting the clock. See the Setting the Alarm section for instructions on setting the alarms. Press and hold the or button for a few seconds when the alarm is sounding or has been snoozed.
button when the alarm is sounding. See the Setting the Alarm section to learn Press the how to set the snooze duration. Press the and buttons simultaneously for a few seconds.
Reset all settings (see above), and use the and buttons to select the region closest to you (USA, EUROPE, JAPAN WIDE, or JAPAN.) Then, press the CLOCK button to save your selection.

Enhanced Remote Features

The enhanced remote lets you operate many functions of your Altec Lansing Moondance Glow speaker system: Turn on your speaker system Press the Turn off your speaker system Press the Change audio source button. button.
Source button Volume decrease button Track back button Alarm disable button Power on/off button Volume increase button Track forward button Play/pause button
Press the button to cycle through and select the audio source: iPod, FM radio or AUX. button. See In iPod mode, press the the Listening to Your iPod section for more information. In iPod mode, Press the Press the + button. Press the button. In iPod mode, press the button. button.
Play a track from your iPod
Pause your iPod Turn up the volume Turn down the volume Skip to the beginning of the current song on your iPod Rewind the currently playing track on youriPod Skip to the beginning of the next song on your iPod Fast-forward the currently playing track on your iPod

FM preset buttons

Snooze button
In iPod mode, press and hold the

In iPod mode, press the

button. 9
Tune radio stations Seek radio stations In FM mode, use the and buttons. See the Listening to the Radio section for additional information. or button. See the Listening to the Radio section for additional
In FM mode, press and hold the information.

Store a radio station

In FM mode, tune to the station youd like to store, and then press and hold one of the PRESET buttons (P1, P2, P3 or P4). See the Listening to the Radio section for more information. In FM mode, press the PRESET button (P1, P2, P3 or P4) that corresponds to the station youd like to hear. See the Listening to the Radio section for more information. See the Setting the Alarm section for instructions on setting the alarms. Press the button when the alarm is sounding.

Select a preset radio station Set the alarm Dismiss the alarm Snooze for 5 to 60 minutes (user-definable)
Press the button when the alarm is sounding. See the Setting the Alarm section to learn how to set the snooze duration.
NOTE For best results, aim the enhanced remote toward the Moondance Glow speaker system.
Wireless Snooze Remote Features
The wireless snooze remote lets you operate select functions of your Altec Lansing Moondance Glow speaker system from across the room. Theres no need to aim it at the speaker system. Snooze Press the snooze timer. button to activate the
Open the battery compartment. Use a coin or screwdriver to turn the battery compartment door counterclockwise.
Position the battery (included) so it sits in the battery holder correctly. Make sure the polarity (the + and sides of the battery) is correct.
Play a track from your iPod Pause your iPod Dismiss the alarm
button. In iPod mode, press the See the Listening to Your iPod section for more information. In iPod mode, press the Press the sounding. or button.
Replace the battery door.
NOTE Please discard used batteries properly. How to Connect and Pair the Wireless Snooze Remote

button when the alarm is

NOTE See the Using the Wireless Snooze Remote section for installation and pairing instructions.
Connect the snooze remote receiver to the SNOOZE REMOTE jack. The jack is located on the back of thesystem.
Using the Wireless Snooze Remote
The Moondance Glow speaker system comes with a wireless snooze remote that allows you to snooze and dismiss your alarm (and play/pause your iPod) from across the room up to 30 feet (10meters) away. In order for the wireless snooze remote to control the speaker system, the snooze remote receiver must be connected to the back of thespeaker system and paired with the wireless snooze remote. How to Install the Wireless Snooze Remote Battery The wireless snooze remote battery (included) is not installed at the factory. To install the wireless snooze remote battery, follow the steps below:
Press the PAIRING button on the bottom of the snooze remote receiver until the corresponding LED light stays lit. Press any button on the wireless snooze remote twice. The LED light on the snooze remote receiver will turn off once the pairing process is complete.

NOTE Any time a button on the wireless snooze remote is pressed, the LED light on the snooze remote receiver will flash.

Listening to Your iPod

Dock your iPod in the Altec Lansing Moondance Glow speakersystem. Select iPod mode. button on your speaker system or enhanced Press the remote until the iPod icon appears on the LCD. Press the button on your iPod, speaker system, enhanced remote, or wireless snooze remote. Music from your iPod will start playing. The speaker system and its remote are capable of controlling basic functions of your iPod. Shuffle function How to Access Additional Features on Your iPod Using the Enhanced Remote Press the P1 button once on the enhanced remote to advance to the next icon is displayed shuffle mode. The when the system is in song shuffle mode. icon is displayed when the The system is in album shuffle mode. The icon disappears when the shuffle function has been turned off. Note: Use the P2 button on some older iPod models. Functionality may vary per iPod model. Press the P2 button once on the enhanced remote to advance to the next icon is displayed repeat mode. The when the system is in the repeat one icon is displayed when the mode. The system is the repeat all mode. The icon disappears when the repeat function has been turned off. Note: Use the P1 button on some older iPod models. Functionality may vary per iPod model. Press the P3 button on the enhanced remote. Press the P4 button on the enhanced remote.
Adjust the volume. Use the + and buttons on the Altec Lansing speaker system to adjust the system volume. Or, use the + and buttons on the enhanced remote.
Find your desired song. Press the or button on your speaker system or enhanced remote to go to the next or previous track. Press and hold the or button on your speaker system or enhanced remote while track is playing for high-speed forward or reverse music search of the current track. Repeat function
Access the previous playlist

Access the next playlist

Charging Your iPod
Whenever your iPod is docked and your Altec Lansing Moondance Glow speaker system is plugged into an AC outlet, your iPod is charging (until fully charged) even if the speaker system is switched off. How to Store Preset Stations Your Altec Lansing speaker systems enhanced remote enables you to program up to 4FM station presets:
Listening to the FM Radio
Plug the FM radio antenna into the speaker systems FM ANTENNA jack. The jack is located on the back of the system.
Tune to the station you wish to store. While in FM mode, use the and buttons on your speaker system or enhanced remote to tune to the desiredstation. Store the station. Press and hold the P1, P2, P3 or P4 button on the enhanced remote for a few seconds. You can store one FM station in each preset. To store other stations, repeat the above steps.

Extend the FM antenna wire fully for best FM reception. Also, do not strip, alter or attach to other antennas. Select FM mode. Press the remote until the button on your speaker system or enhanced appears on the LCD.
How to Recall Preset Stations Make sure you are in FM mode. If youre not in FM mode, press the speaker system or enhanced remote until the button on your appears on the LCD.
Tune to the station you want to listen to. Use the and buttons on your speaker system or enhanced remote to tune in the desired station. Press and hold these same buttons to find the next clear FM station.
Press a PRESET button (P1, P2, P3 or P4) on the enhanced remote. The radio will tune to your preset station. Adjust the volume. Use the + and buttons on the Altec Lansing speaker system to adjust the system volume. Or, use the + and buttons on the enhanced remote.
Listening to a Non-docking iPod or Other Portable Audio Device
If you have a non-iPod MP3 player or other non-docking portable audio device, you can enjoy it through your Altec Lansing Moondance Glow speaker system as well. Just connect it via the AUX jack. Heres how:
When you are finished listening to your portable audio device, please remember to turn both it and your speaker system off to conserve electricity.
Locate a 3.5 mm stereo cable (notincluded). Plug one end of the stereo cable into your device. Your device should have either a headphone or LINE OUT jack for you to plug into.
Plug the other end of the stereo cable into your speaker systems AUX jack. The AUX jack is located on the back of the unit. Select AUX mode. button on your speaker system or the enhanced Press the remote until the AUX icon appears on the speaker systems LCD.
Turn on your device and start it playing. Adjust the volume. Use the + and buttons on the speaker system to adjust the volume. Or, use the + and buttons on the enhanced remote.
NOTE You may need to adjust the device volume also. Your devices volume should be set to approximately volume.

Mood Light

Your Altec Lansing Moondance Glow speaker system is also equipped with a mood light to help you relax and enjoy the music.
Choose the color of the ambient light youd like. Use the and buttons on your speaker system or the enhanced remote to cycle through all the colors the mood light can emit. When the desired color is projected, press the button again to enter the Mood Light Manual Select menu.

Select brightness level. (Optional setting) If in manual mode, press the or button on your speaker system or the enhanced remote to cycle through the available brightness settings. When the desired brightness setting is achieved, press the button to exit the Mood Light Setup menu.
How to Turn On the Mood Light Press the button on your Altec Lansing speaker system.
How to Adjust the Mood Light You can enter the Mood Light Setup menu at any time to change colors, adjust modes and set the brightness level.

Press and hold the

button for 3 seconds.
This puts you in the Mood Light Setup menu.
WARNING The mood light isnt a reading light and doesnt provide enough light to read by. Please dont risk damage to your eyesight by trying to read using the mood light.
Setting the Clock Display
How to Set the Clock Time and Date
Set the minute. Use the and buttons on your speaker system or the enhanced remote to adjust the minute. Then press the CLOCK button to save this setting and enter the AM/PM Set mode, if 12-Hour Clock mode was previously selected. If 24-Hour Clock mode was selected, pressing the CLOCK button will save the minute setting and place the unit into Day Set mode.
Press and hold the CLOCK button for 3 seconds. The CLOCK button is located on the back of your Altec Lansing speaker system. This puts you in the Time/Date Set mode.
Select either 12-Hour or 24-Hour Clock mode. Press the or button on your speaker system or the enhanced remote to select either 12-Hour or 24-Hour Clockmode. Then press the CLOCK button to save this setting and enter the Hour Set mode.
Set AM/PM. Press the or button on your speaker system or the enhanced remote to select AM or PM. Press the CLOCK button to save this setting and enter the Day Set mode.
Set the hour. Use the and buttons on your speaker system or the enhanced remote to adjust the hour. Then press the CLOCK button to save this setting and enter the Minute Set mode.
Set the day. Press the or button on your speaker system or the enhanced remote to select the day of the week. Then press the CLOCK button to save this setting and enter the Month Set mode.
Set the month. Use the and buttons on your speaker system or the enhanced remote to select the month. Press the CLOCK button to save this setting and enter the Date Set mode. Song Information/ If song information is available on your iPod or from Date your radio station, it is displayed. If no song information is available, only the date is displayed.

Set the date. Use the and buttons on your speaker system or the enhanced remote to select the date. Press the CLOCK button to save this setting and enter the Year Set mode.
Song Information Date Clock
Only the song information is displayed, if available. Only the date is displayed. Only the clock is displayed.
Set the year. Use the and buttons on your speaker system or the enhanced remote to select the year. Then press the CLOCK button to save this setting and enter the Display Option mode.
NOTE The clock is always displayed. The size of the clock is dependent on the display option.
11 Set the LCD backlight.
Press the or button on your speaker system or the enhanced remote to cycle through LCD backlight options (off, low, medium, or high.)
10 Set your display options.
Press the or button on your speaker system or the enhanced remote to select one of the following four display options:
NOTE You can also adjust the display contrast by pressing the CLOCK button one step at a time.

Setting the Alarm

Your Altec Lansing speaker system has two separate alarms. How to Set Alarm 1
Press and hold the Turn Alarm 1 on/off
This puts you in the Alarm Set mode for alarm 1. Use the and buttons on your speaker system or the enhanced remote to select alarm ON. Then press the button to save this setting and enter the Alarm Hour Set mode.
Select AM or PM. Use the and buttons on your speaker system or the enhanced remote to select AM or PM. Then press the button to save this setting and enter the Alarm Day Select mode.
NOTE This option is only available if the 12-hour mode was selected when setting up the clock. NOTE If you select alarm OFF, you will exit the menu.
Select alarm day setting. Use the and buttons on your speaker system or the enhanced remote to select the alarm day: Choose EVERYDAY to have the alarm go off every day. hoose WEEKDAYS to have the alarm go off Monday through C Friday. hoose WEEKENDS to have the alarm go off on Saturday and C Sunday.
Adjust the hour. Use the and buttons on your speaker system or the enhanced remote to adjust the hour setting. Then press the button to save this setting and enter the AM/PM selection mode.
Adjust the minute. Use the and buttons on your speaker system or the enhanced remote to adjust the minute setting. Then press the button to save this setting and enter the Alarm Source Set mode.
hoose ONE TIME to have the alarm go off only once at the next C selected time. Then press the button to save this setting and enter the Alarm Source Set mode.
Set the alarm source. Press the or button on your speaker system or the enhanced remote to select the alarm source (iPod, FM radio or buzzer). Then press the button to save this setting and enter the Snooze Duration Set mode. Set snooze duration. Press the or button on your speaker system or the enhanced remote to select the snooze duration. The default snooze duration is 9 minutes and can be adjusted from 5 minutes to 60 minutes in increments of 1 minute. Then press the button to save this setting and enter the Alarm Volume Set mode.

NOTE If you wish to wake up to a specific song on your iPod, dock your iPod on the speaker system, select the song on your iPod, and then select iPod as your alarm source. The speaker system should remember which song was selected from now on, unless the playlist on your iPod is modified. If the playlist on your iPod is modified, either the last song on queue or the first song on your song list will play. NOTE Your Altec Lansing speaker system features a backup battery. If a power failure occurs or the AC cord is accidentally disconnected, the display will not remain lit and the alarm will not function. The correct time, however, will be temporarily maintained (provided you have installed a 9-volt backup battery as described in the Getting Started section). NOTE If the iPod or FM radio are playing when the alarm goes off, the alarm will automatically default to the buzzer, even if the iPod or FM radio have been selected as the alarm source.
Set the alarm volume. Press the or button on your speaker system or the enhanced remote to select the alarm volume (low, medium or high). The default alarm volume is medium. Then press the button to save this setting and exit the Alarm Set mode.
NOTE When exiting the Alarm Set mode, the Alarm is automatically turned on. To dismiss the alarm when it sounds, press and hold the corresponding / button for a few seconds. How to Set Alarm 2 Repeat the above steps, substituting How to Use the Snooze Feature Press the SNOOZE button once to silence the alarm for a period of 5to 60 minutes (user-definable). 19 for.

Setting the Sleep Timer

Your Altec Lansing speaker system is equipped with a sleep timer that automatically turns off the unit 5 to 90 minutes after it has been set. How to Set the Sleep Timer
Maintaining Your Speaker System
Place your speaker system on a level surface away from sources of direct sunlight or excessive heat. Protect your furniture with a cloth or other protective material when placing your speaker system on a natural wood or lacquered finish. Clean your speaker system with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as benzene, thinner or similar materials, can damage the surface of the unit.
Turn on the speaker system. Ensure that your selected audio source is playing. Press and hold the POWER button for 3 seconds. This puts you in the Sleep Timer mode.
Choose when you want the speaker system to turn off. Press the or button on your speaker system or the enhanced remote to select how long the unit should play before going on standby (in 5-minute increments).

Press the POWER button again. This takes you out of the Sleep Timer mode.
NOTE Turning off the system will cancel the Sleep Timer.

Troubleshooting

Symptom Possible Problem AC adapter isnt plugged into a wall outlet or the connector isnt plugged into the power supply jack on the back of the speaker system Wall outlet is not functioning Using the wrong adapter for iPod or no adapter iPod doesnt dock properly iPod didnt install properly Remove your iPod from the dock and check for obstruction on the connectors in the dock and on your iPod. Then reseat it in the dock. Remove your iPod from the dock and check for obstructions on the connectors in the dock and on your iPod. Then reseat it in the dock. Upgrade software on your iPod. For details visit www.apple.com/ipod/download. Please make sure your iPod is working properly before docking into the unit. Please refer to your iPod manual for details. Your speaker system cannot control those iPod models or other devices. See the Welcome section for a compatibility list.
Solution Plug the AC adapter into a wall outlet and plug the connector into the power supply jack on the back of the speaker system.
Speaker system doesnt respond (no power)
Plug another device into the same outlet to confirm the outlet is working. Make sure the adapter is the proper fit for your iPod.
iPod is not installed properly
Your iPod software is too old iPod doesnt respond tothespeaker system

iPod is locked up

Using 1st- or 2nd-generation iPod, iPod shuffle or other devices
Symptom Possible Problem iPod is not installed properly Solution Remove your iPod from the dock and check for obstructions on the connectors in the dock and on your iPod. Then reseat it in the dock. Please make sure your iPod is working properly before docking into the unit. Please refer to your iPod manual for details. Plug the AC adapter into a wall outlet and plug the connector into the supply jack on the speaker system.
iPod is locked up iPod didnt charge AC adapter isnt plugged into a wall outlet, or the connector is not plugged into the power supply jack on the back of the speaker system Volume level is set too high Sound is distorted Sound source is distorted
Decrease the volume. If the iPod original sound source (MP3) is of poor quality, distortion and noise are easily noticed with high-power speakers. Try a different audio source such as a music CD. Replace current battery with a new battery. Point the enhanced remote toward the Altec Lansing speaker system and move within 10feet of the unit. Increase the volume on the device to approximately full volume. Set source selector to AUX.

Battery is weak Enhanced remote doesnt work No sound from the AUX device, such as an MP3 player or CD player connected to the AUX jack Enhanced remote is not pointed toward the speaker system Volume on the device is set too low Source selector is not set to AUX
Symptom Possible Problem Battery is weak Wireless snooze remote doesnt work. Snooze remote receiver is not properly plugged into speaker system Wireless snooze remote is not paired Solution Replace current battery with a new battery. See How to Connect and Pair the Wireless Snooze Remote section.
See How to Connect and Pair the Wireless Snooze Remote section.

Warranty

ALTEC LANSING ONE-YEAR LIMITED WARRANTY What Does the Warranty Cover? Altec Lansing warrants that its products shall be free from defects in materials or workmanship, with the exceptions stated below. What Is the Period of Coverage? This warranty runs for one year from the date of purchase. The term of any warranties implied by law shall expire when your limited warranty expires. Some states and/or Member States in the European Union do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. What Does the Warranty Not Cover? This warranty does not cover any defect, malfunction or failure that occurs as a result of: improper installation; misuse or failure to follow the product directions; abuse; or use with improper, unintended orfaulty equipment. (For information on proper installation, operation and use consult the manual suppliedwith the product. If you require a replacement manual, you may download a manual from www.alteclansing.com.) Also, consequential and incidental damages are not recoverable under this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, sothe above limitation or exclusion may not apply to you. What Will Altec Lansing Do to Correct the Problem? Altec Lansing will, at its option, repair or replace any product that proves to be defective in material or workmanship. If your product is no longer being manufactured, or is out of stock, at its option, Altec Lansing may replace your product with a similar or better Altec Lansing product. How to Get Warranty Service To get a covered product repaired or replaced, you must contact Altec Lansing during the warranty period by email (csupport@alteclansing.com). You must include in your email, your name, address, email address, telephone number, date of purchase and a complete description of the problem you are experiencing. In the United States, you may alternatively contact Altec Lansing by telephone at 1-800-ALTEC88 please be prepared to provide the same information. If the problem appears to be related to a defect in material or workmanship, Altec Lansing will provide you a return authorization and instructions for return shipment. Return shipments shall be at the customers expense, and the return must be accompanied by the original proof of purchase. You should insure the shipment as appropriate because you are responsible for the product until it arrives at Altec Lansing. How Will State Law Affect Your Rights? This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Please note that in the European Union, you as a consumer might have other legal rights under national legislation of European Union Member States governing the sale of Altec Lansings goods. Those rights are not affected by this guarantee. The above limited warranties and remedies are sole warranties and remedies available to purchaser, if, and to the extent, valid and enforceable under the applicable law. Disposal of Old Electrical and Electronic Equipment This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city office or your household waste disposal service.

www.alteclansing.com Headquarters 535 Rte. 6 & 209, Milford, PA 18337-0277 800-ALTEC-88. 570-296-4434. Fax 570-296-6887 Europe 13 Rue Beaumont, L-1219 Luxembourg, Luxembourg Asia/Pacific 23/F, Office Tower, Shun Hing Square Diwang Commercial Centre, 5002 Shen Nan Dong Road, Shenzhen, China 518008
Made for iPod means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performancestandards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Patents pending. 2008 Plantronics, Inc. All rights reserved. ALTEC, ALTEC LANSING, the Altec Lansing logo, the horn design, Moondance, M402, and M402SR are trademarks or registered trademarks of Altec Lansing, a division of Plantronics, Inc. Plantronics, the logo design, and Sound Innovation are trademarks or registered trademarks of Plantronics, Inc. iPod is a trademark of Apple, Inc., registered in the U.S. and other countries. All other trademarks appearing herein are the property of their respective owners. Designed by Altec Lansing in the USA. Made in China. Conu pour liPod signifie quun accessoire lectronique a t spcifiquement conu pour se connecter liPod et est garanti conforme aux normes de performance Apple par le constructeur. Apple nest pas responsable du fonctionnement de ce dispositif, ni de sa conformit aux normes de scurit et rglementations en vigueur. Brevets en instance. 2008 Plantronics, Inc. Tous droits rservs. ALTEC, ALTEC LANSING, le logo Altec Lansing, le logo reprsentant une trompe, Moondance, M402 et M402SR sont des marques dposes ou commerciales dAltec Lansing, une filiale de Plantronics, Inc. Plantronics, le logo et le slogan Sound Innovation sont des marques dposes ou commerciales de Plantronics, Inc. iPod est une marque commerciale dApple Computer, Inc., dpose aux tats-Unis et dans dautres pays. Toutes les autres marques de commerce utilises dans la prsente sont la proprit de leurs dtenteurs respectifs. Conu par Altec Lansing aux tats-Unis. Fabriqu en Chine.

A12934 R06