IMPORTANT SAFETY INSTRUCTIONS
READ INSTRUCTIONS All the safety and operating instructions should be read before the product is operated. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference. HEED WARNINGS All warnings on the product and in the operating instructions should be adhered to. FOLLOW INSTRUCTIONS All operating and use instructions should be followed. CLEANING The product should be cleaned only with a polishing cloth or a soft dry cloth. Never clean with furniture wax, benzine, insecticides or other volatile liquids since they may corrode the cabinet. ATTACHMENTS Do not use attachments not recommended by the product manufacturer as they may cause hazards. WATER AND MOISTURE Do not use this product near water for example, near a bathtub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. ACCESSORIES Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturers instructions, and should use a mounting accessory recommended by the manufacturer. CART A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. GROUNDING OR POLARIZATION If this product is equipped with a polarized alternating current line plug (a plug having one blade wider than the other), it will fit into the outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. If this product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin, it will only fit into a grounding type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding type plug. POWER-CORD PROTECTION - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. OUTDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A. LIGHTNING For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. OVERLOADING Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. OBJECT AND LIQUID ENTRY - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. SERVICING Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. DAMAGE REQUIRING SERVICE - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power-supply cord or plug is damaged. If liquid has been spilled, or objects have fallen into the product. If the product has been exposed to rain or water. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. If the product has been dropped or damaged in any way. When the product exhibits a distinct change in performance this indicates a need for service. REPLACEMENT PARTS -- W hen replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. SAFETY CHECK - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. WALL OR CEILING MOUNTING The product should not be mounted to a wall or ceiling. HEAT The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

SET-UP PRECAUTIONS

Please be sure to make any connections before plugging the CD player in to an electrical outlet. All fader and volume controls should be set to zero or minimum position, before the CD player is switched on. If the CD player has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch on the CD player immediately. The arising condensation of water might damage your device. Leave the device switched off until it has reached room temperature. Operating Determinations: When installing this CD player, please make sure that the device is not exposed or will not be exposed to extreme heat, moisture or dust! Do not operate the CD player in extremely hot (more than 30/100F) or extremely cold (less than 5C/40F) surroundings. Keep the unit out of direct sunlight and away from heaters. Operate the CD player only after becoming familiar with its' functions. Do not permit operation by persons not qualied for operating the unit. Most damages are the result of unprofessional operation.
Audio - www.AmericanAudio.us - CDI-300 Instruction Manual Page 6

MAIN FEATURES

8 times over sampling 1 bit D/A converter Music Master tempo Auto cue Scratch Effect 1/75th second frame search Digital Anti-Shock Real time cue (Cue on the Fly) Selectable Single or Continuous Play 8 different speed scan (4 Forward/4 Reverse) Flash Function (e) Fader Q Start Control (a) Sleep Mode (f) Digital RCA coaxial output Jog Wheel Pitch Bend +/-100% Large bright Digital Screen can be viewed from wide angles. Flip-Flop (Relay Playback) (b) 381 programmable Cue Points (127 x 3) (d) Pitch display Seamless Loop (uninterrupted loop playback) Sampler (Forward & Reverse Sampling) Memory Backup, Defaults to last setting (c) Visual Marker Display with 1:1 Ratio 4 Programmable Cue and Sample (Bank) Buttons, 7 sec. Samples for each Bank Button Adjustable Pitch Percentages: +/-4%, +/-8%, +/-16% or +/-100% Instant Start within 10 ms (sound is produced immediately when the PLAY button is pressed)
(a) FADER Q START CONTROL: This feature is used in conjunction with most American Audio and American DJ audio mixers that also feature Fader Q Start control. For best results use this feature with two (2) CDI-300 players. Connect your CDI-300s as described in the set-up section of this manual. After set up is completed load your players. By moving the mixers crossfader from left to right you can start and pause your CDI-300 playback functions. For Example, when using two (2) CDI-300 players and a Fader Q Start mixer, if your mixers cross fader is all the way to the left (player one is playing, player two is in cue or pause mode), and you move the fader at least 20% to the right, player two (2) will begin to play and player one (1) will return to cue mode. When the cross fader is to the right, and you move it 20% to the left, player one (1) will begin to play and player two (2) will return to its cue point. You can create great effects similar to scratching with this feature. After storing cue points on each side of the CD player, different songs or samples may quickly be recalled by moving the mixer crossfader back and forth. New cue points can be easily selected on the CDI-300 player (see setting cue points page 16). Q Start control is easy to use and mastering this feature will help you create amazing effects with your music. Note: For proper Q Start operation be sure your mixers Hamster setting are set to 1/2 (Normal Setting). (b) FLIP-FLOP: This feature is used in conjunction with American Audio mixers that also feature Fader Q Start. For FLIP-FLOP results you must use two (2) CDI-300 players. Connect your CDI-300s as described in the set-up section of this manual. This feature will start the next player once one (1) player has ended. For example, if player one (1) is playing a disc and it ends, player two (2) will instantly begin to play. You may set FLIP-FLOP to play track to track or disc to disc. For more information on this feature, see FLIP-FLOP on page 25. (c) MEMORY BACKUP: The CDI-300 has a five (5) year memory back-up, that will save your setting in case the power supply is accidentally disconnected. CDI-300 will remember your last setting even if you disconnect your main power. The CDI-300 will store your cue points and samples in memory if you accidentally eject a disc or shut off the power. See memory on page 21. (d) PROGRAMMABLE CUE POINTS: The CDI-300 has four BANK BUTTONS (4). 127 Cue points can be stored in each of the BANK BUTTONS (4), for a total of 381. These cue points can be stored into the unit's internal memory and may be recalled at any time. See setting "Cue Points" on page 16 (e) FLASH START FUNCTION: This feature is used in conjunction with most American Audio and American DJ audio mixers that also feature Fader Q Start control. This function work similar to the Fader "Q" Start Control described above. In this case the crossfader is used to start and stop any sample that is stored in the players memory.

(f) SLEEP MODE: The CDI-300's laser and pick-up assembly will power down after 15 minutes of inactivity (when in
pause or cue mode). This will lengthen the life of your motor drive and laser. To initialize the player, just press the cue or play buttons.
Audio - www.AmericanAudio.us - CDI-300 Instruction Manual Page 7

SET-UP

1. Checking the Contents Be sure your CDI-300 was shipped with the following: 1) CDI-300 Professional CD player. 2) Operating instructions (this booklet). 3) One (1) set of RCA cables. 4) One (1) 1/8 mini plug. 5) Warranty card. 2. Installing the Units Place your unit on a flat surface or mount it in a flat surface case 3. Connections 1) Be sure the power is disconnected. 2) Connect the included RCA cable from your CDI-300 outputs to the inputs on your mixer. 3) Use the supplied 1/8 mini plug cable to connect your CDI-300 to a mini jack connection (A or B ) on a compatible American Audio or American DJ Fader Q Start mixer. CAUTION: Be sure to use the supplied mono 1/8" control cables. Using other types of cable may result in unit damage To avoid severe damage to the unit, be sure the power is off when making connections to the unit. CAUTION: The player will work normally when the main unit is mounted with the front panel within 15 degrees of the vertical plane If the unit is tilted excessively, discs may not be loaded or unloaded properly. (Figure 1)

Figure 1

CAUTION: The LCD is designed to be clearly visible within the angles shown in Figure 2. Mount the control unit so that the visual angle is within this range.

Figure 2

Audio - www.AmericanAudio.us - CDI-300 Instruction Manual Page 8
GENERAL FUNCTIONS AND CONTROLS
P R O F E S S IO N A L C D P L AY E R

Figure 3

A. TOP UNIT CONTROLS (FIGURE 3)
1. PITCH PERCENTAGE SELECTOR - Press this button to select pitch range percentages of 4%, 8%, 16%, and 100%. See adjusting the PITCH SLIDER'S RANGE on page 28. 2. TEMPO LOCK FUNCTION - This button activates the TEMPO LOCK function. This function allows you to use the PITCH SLIDER to speed up or slow down playback speed without altering the tonal pitch of the track. When this function is not engaged the original tonal pitch of the track will be altered giving you the "chipmunk" effect when a track is played at a high rate of speed, or the "James Earl Jones" effect when a track is slowed to much. 3. BPM/PITCH ON/OFF BUTTON - This button is used to toggle between the PITCH SLIDER (5)
function and AUTO BPM counter. To activate the BPM counter, you must hold the button down for at least 3 seconds. When the button LED is lit the PITCH SLIDER (5) is active. When the button LED is not lit, the PITCH SLIDER (5) is not active. The pitch percentage can be changed between 4%, 8%, 16% and 100%. 4% will allow the least amount of pitch manipulation and 100% will allow the most amount of pitch manipulation. 4. BANK BUTTONS 1-3 - These buttons are used to store either three (3) cue points or three (3) samples. Each Bank Button can store either a sample or a cue point. 5. PITCH SLIDER - This slider is used to adjust the playback pitch percentage. The slider is a set adjustment and will remain set until the pitch

Audio - www.AmericanAudio.us - CDI-300 Instruction Manual Page 9
GENERAL FUNCTIONS AND CONTROLS (Cont.)
slider is moved or the pitch function has been turned off. This adjustment can be made with or without a disc in the drive. The pitch adjustment will remain even if a disc has been removed and will reflect on any other disc loaded into the player. That is to say, if you set a +2% pitch on one disc, remove that disc and insert another, that disc too will have a +2% pitch. The amount of pitch being applied will be displayed in the LCD (22). 6. TIME MODE - The TIME button will switch the time value described in the TIME METER between ELAPSED PLAYING TIME, TRACK REMAINING TIME, and TOTAL REMAINING TIME. 7. (+) PITCH BEND BUTTON - The (+) pitch bend function creates a momentary BUMP in the CDs BPMs (Beats per minute) while it is playing. This will allow you to match the beats between two playing CDs or any other music source. Remember, this is a momentary function. When you remove your finger from this button, the BPMs will automatically return to PITCH SLIDERS (5) selected pitch. Holding down this button will give a maximum of +100% pitch. (-) PITCH BEND BUTTON - The (-) pitch bend function creates a momentary Slow Down in the CDs BPMs (Beats per minute) while it is playing. This will allow you to match the beats between two playing CDs or other playing music source. Remember, this is a momentary function. When you remove your finger from the pitch button, the BPMs will automatically return to PITCH SLIDERS (5) pitch value. Holding down this button will give a maximum of -100% pitch. Use this function to slow to another playing music source. Be sure to notice that this function is a momentary pitch adjustment, for a more precise adjustment use the PITCH SLIDER (5) to match the BPMs with another playing music source. 8. SGL/CTN - This function allows you to choose between single track play or continuous track play (all tracks in order). This function also operates in FLIP-FLOP mode. 9. SCRATCH EFFECT BUTTON - This button is used to activate and deactivate the Scratch
effect. 10. JOG WHEEL/EFFECTS PLATTER - This wheel has two functions; A. The jog wheel will act as a frame search control when the CD is in pause or cue mode, allowing you to set a cue point. B. The wheel also works as a pitch bend during Playback. Turning the wheel clockwise will increase the pitch percentage up to 100%, and turning the wheel in the counter-clockwise direction will decrease the pitch percentage down to -100%. The pitch bend will be determined on how long you turn the jog wheel continuously. 11. CD LED - This LED will light up when a CD is loaded and the player is ready for use. 12. EJECT FUNCTION - Pressing this will eject the CD. The eject function will only when the unit is in cue mode, this is to prevent accidentally ejecting the disc when in play mode. 13. MEMORY BUTTON - This button allows you to program up to three (3) cue points or three (3) samples in to the three BANK BUTTONS (3). The samples or cue point can then be recalled at any time even when the disc has been removed and replaced at a later time. 14. PLAY/PAUSE BUTTON - Each press of the PLAY/PAUSE BUTTON causes the operation to change from play to pause or from pause to play. While in play mode the green play LED will glow, and while in pause mode the green play LED will flash. 15. SAMPLER BUTTON - This is used to activate the sampler function. When this function is activated a created sample will play in a continuous loop mode. 16. CUE - Pressing the CUE button during playback immediately pauses playback and returns the track to the last set cue point (see setting a CUE POINT, page 16). The red CUE LED will glow when the unit is in cue mode The LED will also flash every time a new CUE POINT is set. The CUE button can be held down to momentarily play the CD. When you release the CUE button it

Audio - www.AmericanAudio.us - CDI-300 Instruction Manual Page 10
instantly returns to the CUE POINT. 17. RELOOP BUTTON - If a SEAMLESS LOOP has been made (see setting a SEAMLESS LOOP on page 17), but the CD Player is not actively in SEAMLESS LOOP mode (a loop is not playing), pressing the RELOOP BUTTON will instantly reactivate the SEAMLESS LOOP mode. To exit the loop, press the OUT BUTTON (18). LOOP and RELOOP will appear in the LCD DISPLAY (22) when the RELOOP function is available. 18. OUT BUTTON - This button is used to set the ending point of a loop. A loop is started by pressing the IN BUTTON (19), and pressing the OUT BUTTON to set the loop ending point. The loop will continue to play until the OUT BUTTON is pressed once again. 19. SEAMLESS LOOP IN BUTTON - CUE ON THE FLY - This function allows you to set a CUE POINT (see CUE POINT page 16) without music interruption (on the fly). This button also sets the starting point of a seamless loop (see SEAMLESS LOOP). 20. TRACK BUTTON - This button is used to select a track. Tapping this button will forward skip to the next track, holding down this button will rapidly forward skip through the tracks. TRACK BUTTON - This button is used to select a track. Tapping this button will back skip on track, holding down this button will rapidly back skip through the tracks. 21. SEARCH KNOB - This knob has four forward and four reverse speed positions allowing you to quickly scan through tracks. The more you turn the wheel in either direction, the faster your search. 22. LCD DISPLAY - This high quality LCD display indicates all the functions, as they are occurring. This display is viewable at several comfortable angles (see page 13). The display ICONS will be explained in section D.
Audio - www.AmericanAudio.us - CDI-300 Instruction Manual Page 11

Figure 4

230V 115V

POWER ON OFF

Figure 5

B. REAR PANEL (FIGURE 4)

23. VOLTAGE SELECTOR - Because power supplies vary from location to location we have incorporated a selectable voltage switch. This switch can select a voltage input of 120v~60Hz or 220v~50/60Hz. Always disconnect the power plug before changing the voltage. 24. POWER CONNECTOR - This connection is used to connect your main power. Be sure that your local power matches the units required power. NEVER REMOVE THE GROUND PRONG FROM THE POWER CABLE, DOING SO MAY RESULT IN IMPROPER OPERATION. 25. POWER BUTTON - This button is used to turn your units power on and off. 26. CUE MINI JACK - Connect the supplied mini-plug from the CUE jack on the rear of your unit to a compatible American Audio mixers CONTROL out. This feature is only available on American Audios Q series mixers.
27. DIGITAL OUT - Use this connection to create near perfect copies of your disc to a Mini disc, CD-R, or any other digital recording device. 28. AUDIO OUT R & L - Audio out signals. Connect stereo RCA cables from AUDIO OUT to a mixer's line input.

C. FRONT PANEL (FIGURE 5)
29. TRANSPORT TRAY - This tray is used to load and unload a compact disc. The tray is opened and closed by pressing the OPEN/CLOSE BUTTON (12). Never attempt to force the transport tray open or closed when the power is turned off.
Audio - www.AmericanAudio.us - CDI-300 Instruction Manual Page 12

Figure 6

D. LCD DISPLAY PANEL (FIGURE 5)
30. PAUSE INDICATOR - This indicator will glow when the drive is in pause mode. 31. MEMORY BUCKET INDICATOR - This indicator serves two functions. The bucket outline details the cue memory status, a full bucket outline indicates the cue memory is full. The four bars in the memory bucket detail the anti-shock memory state. Each bar indicates 2 seconds of digital anti-shock. The search functions will not operate until all the bars are full. 32. CUE INDICATOR - This indicator will glow when the unit is in CUE or mode and will flash every time a new CUE POINT is set. 33. PITCH METER - This meter will display the pitch percentage applied by the PITCH SLIDER (5). 34. TIME BAR INDICATOR - This bar gives a visual approximation of a track's or disc's remaining time. This bar will begin to flash when a CD is ending, or a track if the unit is in "SINGLE" mode. 35, 36, 37. TIME DISPLAY - These indicators detail the Minutes, Seconds, and Frames. The meter will display either the elapsed, total, or remaining time of a track or disc. The time displayed in the meter will directly reflect the time indicator above TOTAL REMAIN (39), OR REMAIN (38). 38. REMAIN INDICATOR - When "REMAIN"
is indicated in the LCD DISPLAY (22) the TIME DESCRIBED (35, 36, & 37) in the LCD will define the current track's remaining time. 39. TOTAL/REMAIN INDICATOR - When "TOTAL" and "REMAIN" are indicated in the LCD DISPLAY (22) the TIME DESCRIBED (35, 36, & 37) in the LCD (22) will define the total disc remaining time. 40. RELOOP INDICATOR - Appears when LOOP is engaged or ready to be engaged. 41. LOOP - This icon will flash when you are in loop mode. This icon will glow when a loop has been created but is not actively playing. 42. SINGLE INDICATOR - This indicates that the CD drive is in single play mode, the track will play once and return to CUE mode. If the single indicator is not on the unit is in continuous mode In continuous mode the drive will play all the remaining tracks on the disc. Once the remaining tracks have ended the unit will return to cue mode 43. CD DIRECTION INDICATOR - Indicates the direction the CD is rotating. Counter-Clockwise rotation means the CD is playing in reverse. 44. TRACK INDICATOR - This 2-digit indicator visually details the current track cued or playing. 45. PLAY INDICATOR - The "PLAY" indicator will glow when the unit is in play mode.

Figure 10

6. PAUSING - Figure 10
This function pauses playback at the exact same point the PLAY/PAUSE BUTTON (14) was pressed. Pressing the PLAY/PAUSE BUTTON (14) will switch between play and pause modes. When the unit is in pause mode the PAUSE INDICATOR (30) will show in the LCD DISPLAY (22). The green PLAY/PAUSE BUTTON (14) LED will also begin to flash repeatedly.

7. FRAME SEARCH

This feature allows you to scroll through a track frame by frame, allowing you to find and set a starting cue, sample, or loop point. To use the scroll function you must first be in Pause Mode (see section 6) or Cue Mode (see section 9). Once you are in Pause or Cue mode, turn the JOG WHEEL (10) to scroll through the track (Figure 13). Turning the wheel in a clockwise direction will advance the frame search and turning the wheel in a counter-clockwise direction rewinds the frame search. When you use the JOG WHEEL (10) the monitor (headphone level) function allows you to here what you are scrolling through. Once you reach your desired starting point you can set a cue (starting) point by pressing the PLAY/ PAUSE BUTTON (14) as in Figure 10. Pressing the CUE BUTTON (16) as in Figure 11 will now return you to the point you just set.

Figure 12

Figure 11
Audio - www.AmericanAudio.us - CDI-300 Instruction Manual Page 15
8. SCANNING (FAST FORWARD / FAST REVERSE)
This function gives you a fast search through a disc or track. Turn the SEARCH KNOB (21) in clockwise direction for fast forward or turn the knob counterclockwise for fast reverse. You can scan in four different forward and four different reverse speeds depending on how much you rotate the knob.

Figure 13

9. SETTING and STORING a CUE POINT: Setting A Cue Point:
A cue point is the exact point playback will begin when the PLAY/PAUSE BUTTON (14) is pressed. You may set your cue points anywhere on a disc or in a track. You may set up to four independent cue points per disc. Four cue points are stored in the BANK BUTTONS 1-3 (4) and one is shared by the IN BUTTON (19) and the CUE BUTTON (16). There are two (2) ways to set and create a CUE point as detailed in figures 14 and 15

1) You may press the IN BUTTON (19) on the fly (while the disc is playing). This will set a CUE Point without music interruption. Pressing the CUE BUTTON (16) will now return you to the same point that you pressed the IN BUTTON (19). You may now store this CUE Point in any of the BANK BUTTONS 1-3 (4). Pressing the CUE BUTTON (16) or the IN BUTTON (19) will now return you to this exact point.

Figure 14

2) You may also use the JOG WHEEL (10) to set a cue point. While a disc is in PAUSE or CUE mode, use the JOG WHEEL (10) to scroll through a track and find your desired starting point. Once you have found your desired CUE point press the PLAY BUTTON (14) to set your cue point. Pressing the CUE BUTTON (16) or the IN BUTTON (19) will now return you to this exact point.

Figure 15

Audio - www.AmericanAudio.us - CDI-300 Instruction Manual Page 16

Storing A Cue Point:

Once you have set your CUE Point by one of the two means listed on page 16, you may store your cue point in one of the BANK BUTTONS (4). Once you store this cue point in memory you may recall it at any time and you may even recall memory if the disc has been removed or power had been disconnected, see SYSTEM MEMORY on page 21. You may store a maximum of three cue points per disc and maximum of 381 cue points can be saved in the unit's memory. The MEMORY BUCKET (31) in the LCD DISPLAY (22) will approximate the available memory. Either a CUE POINT or a SAMPLE (See creating a SAMPLE LOOP at the bottom of this page) can be stored into a BANK BUTTON (4) not both. To Store a cue point: 1) Create a Cue Point by one of the two means listed on page 16. Press the MEMORY BUTTON (13), as in Figure 16. The red Memory Cue LED will glow indicating the store memory function has been activated. You may now press any one of the three BANK BUTTONS (4) to store your cue point into memory (Figure 17). After pressing one of the BANK BUTTONS (4), the corresponding Bank Button LED will flash briefly. The LED of the BANK BUTTON (4) will remain lit indicating either a sample or cue point is stored in memory. The red Memory LED will turn off.

Figure 16

Figure 17
2) Repeat the above steps to store up to two more Cue Points. Once your three cue points have been stored you may access them at any time. During playback the cue points will instantly start playback from that point without any music interruption. Please note in order to access these cue point, the disc used to create the cue points must be loaded.
10. CREATING AND PLAYING A SEAMLESS LOOP
A seamless loop is a sound loop that plays continuously without sound interruption. You can use this loop to create dramatic effect in your mixing. This loop has no time limit and you could actually loop the entire length of disc. You create a seamless loop between two continuous points of a disc.

1) Press PLAY/PAUSE BUTTON (14) to activate playback mode
2) Press the IN BUTTON (19). This will set the starting point of the SEAMLESS LOOP. The IN BUTTON (19) LED will light.

Figure 18

Figure 19
Audio - www.AmericanAudio.us - CDI-300 Instruction Manual Page 17
3) Press the OUT BUTTON (18) to set the ending point for your SEAMLESS LOOP (Figure 20). The IN BUTTON (19) and OUT BUTTON (18) LEDs will immediately begin to flash rapidly, indicating the SEAMLESS LOOP mode has been activated.
LCD LOOP INDICATORS - During a seamless loop, the LOOP (41) and
RELOOP (40) INDICATORS will turn on in the LCD DISPLAY (22) indicating a loop is active.

Figure 20

EXITING A LOOP - To exit a SEAMLESS LOOP, press the OUT BUTTON (18). The IN BUTTON (19) and OUT BUTTON (18) LEDs will remain on, but will stop flashing. Music playback will resume normal play. The IN BUTTON (19) and OUT BUTTON (18) LEDs will remain on to remind you that a loop is stored in memory.

Figure 21

REPLAY LOOP - The RELOOP (17) function allows you to return to your
stored loop at any time. The IN BUTTON (19) and OUT BUTTON (18) LEDs will indicate a loop is stored in memory, and may be played at any time. To replay the loop, press the RELOOP BUTTON (17). The IN BUTTON (19) and OUT BUTTON (18) LEDs will again begin to flash indicating SEAMLESS LOOP mode has been activated and your stored loop will immediately begin to play.

Figure 22

11. EDITING A LOOP:
Please note: Only the ending point of the loop may be edited. You may make your loop shorter or longer. Before you can edit your seamless loop you obviously must first create a seamless loop to edit. If you havent created a SEAMLESS LOOP, follow the instructions in step 10 to create a loop. If a SEAMLESS LOOP has already been created, press the RELOOP BUTTON (17) to activate your SEAMLESS LOOP (Figure 22) if it is not already activated. To edit your seamless loops ending point: 1) Press the OUT BUTTON (18) to return to normal play from the loops cue point. (Figure 21). This will disengage the SEAMLESS LOOP mode and allow you to edit the loops ending point. 2) Press the OUT BUTTON (18) again when you reach your new ending point (Figure 21). - FOR A SHORTER LOOP: Press the OUT BUTTON (18) at sooner point in the track (Figure 21). - FOR LONGER LOOP: Press the OUT BUTTON (18) at later point in the track (Figure 21).

Audio - www.AmericanAudio.us - CDI-300 Instruction Manual Page 18
12. Using the Built In Sampler:
Your CDI-300 comes with an advanced built in sampler. You may store up to four samples. One sample in each of the four BANK BUTTONS (4) (Once again please note you may only store either a CUE POINT or a SAMPLE into a BANK BUTTON (4), not both). Your sample can be a maximum of 6.5 seconds in length. A sample can be recalled while a CD is playing, while the CD drive is in PAUSE MODE, you may even play a sample when the CD has been removed. You may play your sample at anytime without music interruption. If you play your sample when the unit is already in playback mode you sample will over lap the current music source. You can also play your sample once or in a continuous loop. As with cue points you may store approximately 381 (127 x 3) samples in a drives memory (depending on available memory). The MEMORY BUCKET (31) on the LCD DISPLAY (22) will approximate the remaining memory.

To create a sample:

1) Initialize a loop (see creating a seamless loop on page 17). If your loop is longer than 6.5 seconds it cannot be stored as a sample and will stored as a Cue Point.

Figure 23

Figure 24

2) Press the MEMORY BUTTON (13). The MEMORY BUTTON (13) red LED will glow indicating memory is ready to be stored.
3) Select one of the four BANK BUTTONS (4) you wish to store your loop in and press that button.
4) The red MEMORY BUTTON (13) LED will turn off, when your sample is locked into memory. 5) At this point your sample has been stored into memory. The original loop you used to create the sample will remain playing until the OUT BUTTON (18) is pressed (Figure 25). 6) Your sample can now be recalled at any time even when the unit is in PAUSE MODE. To recall the sample be sure the sample function is on, by pressing the SAMPLE BUTTON (15) until the red sample button LED turns on. To play your sample in a continuous loop leave the sample function on. To play your sample just once, turn the sample function off immediately after initiating your sample. With the sample function on, the sample will continue to play until the sample function is turned off. Figure 25 7) Important Notice: If you try to activate your sample without turning the sample function on, the BANK BUTTON (4) will act as cue Figure 26 point!

Audio - www.AmericanAudio.us - CDI-300 Instruction Manual Page 19

13. BANK BUTTONS (4):

Figure 29

16. RECALL FLASH MEMORY:
The CDI-300 can store all your user programmed cue points in to memory. These cue points may be recalled at any time, even when a disc has been removed and reinserted at a later time. To recall the memory on a specific disc; 1) Be sure a CD is not loaded in to the drive. 2) Press the MEMORY BUTTON (13) down until the red memory LED turns on. 3) Insert the CD. "RECALL" will appear in the LCD (21) while the memory is being installed and the red MEMORY BUTTON (13) LED will turn off.

Figure 30

17. CLEAR ALL MEMORY:
You may clear the system memory at any time. This will erase all your programmed memory and restore the unit to it's default settings. To clear the memory; While main power is turned off, turn the SEARCH KNOB (20) in a counter-clockwise direction. While the search knob is turned in a counter-clockwise direction turn main power on. The LCD (22) will flash three times and default memory will be restored.
18. FIRMWARE VERSION DISPLAY:
You may display the units firmware version. Firmware is the units internal programming code. To view the firmware version; While main power is turned off, turn the SEARCH KNOB (21) in a clockwise direction. While the search knob is turned in a clockwise direction turn main power on. The firmware version will appear in the LCD (22), as long as the search knob is held in the clockwise position.
Audio - www.AmericanAudio.us - CDI-300 Instruction Manual Page 21

PITCH ADJUSTMENTS

AUTO BPM COUNTER/PITCH ADJUSTMENTS:
You can activate the AUTO BPM counter by pressing the BPM/PITCH ON/OFF BUTTON (3) for at least 3 seconds. When the button LED is lit, the PITCH SLIDER is active and the pitch can be adjusted. When the button LED is not lit. the AUTO BPM counter is active and the PITCH SLIDER is not active. The different pitch adjustments allow a track's or a loop's playback speed to be manipulated. This speed manipulation is commonly used to beat match between two or more music sources such as a turntable or another CD player. The playback speed may be increased or decreased by a factor of +/-100. The next section details the different pitch manipulation schemes.

1. PITCH SLIDER (33):

This function will increase or decrease the tracks playback speed or "PITCH." The maximum pitch percentage manipulation in this function is +/-100%. The PITCH SLIDER (5) is used to decrease or increase the playback pitch. If the slider is moved up (towards the top of the unit) the pitch will decrease, if the slider is moved down (towards the bottom of the unit) the pitch will increase. The PITCH SLIDER adjustment can be changed to range from +/-4%, +/-8%, +/-16%, or +/-100% (See changing "PITCH SLIDER PERCENTAGE RANGE" on the next page). This pitch adjustments will effect normal playback and loops only when the PITCH ON/OFF BUTTON (3) is turned on. The pitch adjustments will not affect your samples.

Figure 31

Activating the Pitch Slider (5): To activate the PITCH SLIDER you must
turn on the pitch adjustment function. Press the ON/OFF BUTTON (3) located at the top right of the unit. The ON/OFF BUTTON (3) LED will glow when the function is activated. If the pitch function is not activated the PITCH SLIDER will not function.

Figure 32

Using the Pitch Slider (5): Be sure the pitch function has been activated as described above. To use the PITCH SLIDER slide the slider up and down. Down will increase the pitch and up will decrease the pitch.

Figure 33

Audio - www.AmericanAudio.us - CDI-300 Instruction Manual Page 22
Adjusting the PITCH SLIDER'S RANGE (5): You may change the PITCH SLIDER'S (5) operating range at any time. To change the operating range be sure the pitch function is turned on, see figure 33. The pitch percentage can be changed between +/-4%, +/-8%, +/-16%, and +/- 100%. 4% will allow the least amount of pitch manipulation and 100% will allow the most amount of pitch manipulation. To adjust the different ranges, press the PITCH ON/OFF BUTTON (3) and tap on the PITCH RANGE BUTTON (1) until your desired value is reached, see figure 34.

Figure 34

2. PITCH BENDING: Unlike the PITCH SLIDER (5) adjustment this function will momentarily increase or decrease a tracks speed
during playback. There are two ways to operate this function with the (-) & (+) PITCH BUTTONS (7) or with the JOG WHEEL (9). The maximum pitch bend percentage allowed is +/- 100%. The pitch bend function will work in conjunction with the PITCH SLIDER (5) pitch setting. For example, if the PITCH SLIDER (5) is set to a 2% pitch gain the pitch bending process will begin at 2% and will continue to the maximum of +/- 100%.
NOTE: A -100% pitch manipulation will stop playback entirely.
Holding down or tapping on the (-) PITCH BEND BUTTON (7) will provide a slow down in the playback pitch.

Figure 35

Holding down or tapping on the (+) PITCH BEND BUTTON (7) will provide a speed bump in the playback pitch.

Figure 36

PITCH BEND BUTTONS (7):
The (+) PITCH BEND BUTTON (7) will increase track playback speed and the (-) PITCH BEND BUTTON (7) will decrease track playback speed. The extent to which the speed changes is proportionate to the amount of time the button is pressed. For example, if the (+) PITCH BEND BUTTON (7) is held down continuously as in figure 36, the disc speed will increases and will continue to increase until it reaches a maximum of 100% speed gain. When you release the (+) PITCH BEND BUTTON (7) the disc speed will automati ally return to its previous set speed.
Audio - www.AmericanAudio.us - CDI-300 Instruction Manual Page 23

3. JOG WHEEL (10):

The JOG WHEEL will temporarily bend the pitch if a track is in playback mode Rotating the wheel in a clockwise direction will increase your track pitch and rotating the wheel in a counter-clockwise direction will slow your track pitch. The speed you rotate the JOG WHEEL will determine pitch bend percentage (%). For example, if the JOG WHEEL is continuously turned in a counterclockwise direction the playback speed will steadily decrease and will continue to decrease until playback reaches a maximum of -100% and playback stops entirely. When you stop turning the JOG WHEEL the disc speed will automati ally return to its previous set speed.

Designed For The Working Professional.

CONTENTS:

DIGITAL MEDIA PLAYERS / MIDI CONTROLLERS SOUND CARDS / POCKET RECORD MEDIA PLAYBACK SOLUTIONS CD / MP3 PLAYERS PRO MIXERS PA MIXERS P. 134-139 P. 140 P. 141-143 P. 144-148 P. 149-154 P. 155-157
PRO AMPLIFIERS RACK ESSENTIALS AUDIO ESSENTIALS SOUND REINFORCEMENT CASES & ACCESSORIES
P. 158-160 P. 161 P. 162-163 P. 164-167 P. 168

www.americanaudio.eu

www.americanaudio.us

AMERICAN AUDIO

DIGITAL MEDIA PLAYERS / MIDI CONTROLLERS

RA D I US 0 0

pr ofessional single mp3 /cd player
Whether you DJ with CDs or a computer, the American Audio, Radius 1000 will help you achieve the next level! The Radius 1000 is a professional CD/MP3 player with Midi capabilities so DJs can control their favorite music playback software. It features a large 6-inch (150mm) jog wheel, 9 on-board DSP effects, and a large bright display that shows track titles and artist ID tags. Radius 1000 has a red LED visual marker display that rotates around the jog wheel to show the reference point of where the CD/MP3 disc is playing. The Radius 1000 also offers features only found on the highest quality CD Players, such as: Slot load CD Drive, Quick MP3/CD disc recognition, Advanced Track Search (search for a new track while one is playing), 10 seconds of Anti-shock memory, Seamless Loop, 3 Flash Start buttons, Digital BPM Counter, and Digital Output (S/PDIF). F E AT U R E S :. Plays MP3, CD & CD-R discs. Midi software compatible via USB (Control up to 8 MIDI channels at once). Display shows track titles and artist from ID tags when played. Advanced cueing with track searching by frame (not by each second). Quick MP3/CD recognition. Track and Folder Search. Advanced Track Search: Search for a new track while one is playing. PowerTouch advanced digital scratching (with adjustable sensitivity). 2 Scratching modes: Digital Scratch mode, Beat Juggle mode. Tempo Lock. Instant Start. 9 On-board FX: Scratch, Filter, Echo, Trans, Skid, Phase, Flanger, Pan, Bop. 6-inch (150mm) Jog Wheel with LED Cue marker and adjustable LED effects. 3 mode Jog Wheel: Normal, Scratch, and Auto Cue Scratch(Great for Beat Juggling). Time & Ratio adjustment for digital FX. FX sync adjustment. Red LED Visual marker display: Reference point to view where the disc is playing. Digital BPM Counter: keeps digital FX in sync with music.TAP Button for manual BPM. Anti Shock (10 sec.). Smart loop: Automatically measures your loop. Fader Q Start. Independently adjustable Pitch Bend (up to 100%). Sleep Mode (Adjustable in increments of 5 min - up to 120 minutes). 3 Flash Start Buttons with (5 second sample each button). Recall memory of Q-Start and samples. Store up to 1500 cue points. Digital Output (S/PDIF). Headphone jack on rear with volume control. Slot load CD drive. Flip Flop Relay playback between two Radius 1000 CD/MP3 Players. Dimensions (LxWxH): 10.5 x 14 x 4.25 / 265x356x106 mm. Weight: 8 lbs. / 3.6 kgs.

R A DIUS 3000

pr ofessional media player
Whether you DJ with CDs or a computer, the American Audio, Radius 3000 will help you achieve the next level! The Radius 3000 is a professional CD/MP3/WAV player with Midi capabilities so DJs can control their favorite music playback software. It features a large 6-inch (150mm) jog wheel, 9 on-board DSP effects, and a large bright display that shows track titles and artist ID tags. Radius 3000 has a white LED visual marker display that rotates around the jog wheel to show the reference point of where the CD/MP3/WAV disc is playing. The Radius 3000 also offers features only found on the highest quality CD Players, such as: Slot load CD Drive, Quick CD/MP3/WAV disc recognition, SD Card and USB inputs, Advanced Track Search (search for a new track while one is playing), 10 seconds of Anti-shock memory, Seamless Loop, 3 Flash Start buttons, Digital BPM Counter, and Digital Output (S/PDIF). F E AT U R E S :. Plays MP3, WAV*, CD & CD-R discs. Includes SD Card and USB inputs for additional music playback sources (such as SD, SDHC, USB Hard Drives). New & improved Database Builder for USB Drives: Sort your music by Title, Artist, Album or Genre in alphabetical order (ID3 tag info). Midi software compatible via USB (Control up to 8 MIDI channels at once). Display shows track titles and artist from ID tags when played. Advanced cueing with track searching by frame (not by each second). Quick MP3/CD recognition. Track and Folder Search. Advanced Track Search: Search for a new track while one is playing. PowerTouch advanced digital scratching (with adjustable sensitivity). 2 Scratching modes: Digital Scratch mode, Beat Juggle mode. Tempo Lock. Instant Start. 9 On-board FX: Scratch, Filter, Echo, Trans, Skid, Phase, Flanger, Pan, Bop. 6-inch (150mm) Jog Wheel with LED Cue marker and adjustable LED effects. 3 mode Jog Wheel: Normal, Scratch, and Auto Cue Scratch (Great for Beat Juggling). Time & Ratio adjustment for digital FX. FX sync adjustment. White LED Visual marker display: Reference point to view where the disc is playing. Digital BPM Counter: keeps digital FX in sync with music.TAP Button for manual BPM USB COMPACT DISC SLOT. Anti Shock (10 sec.) HARD DRIVE MP3 WAV. Smart loop: Automatically measures your loop. Fader Q Start. Independently adjustable Pitch Bend (up to 100%). Sleep Mode (Adjustable in increments of 5 min - up to 120 minutes). 3 Flash Start Buttons with (5 second sample each button). Recall memory of Q-Start and samples HEADPHONE OUTPUT. Store up to 1500 cue points. Digital Output (S/PDIF). Headphone jack on rear with volume control. Slot load CD drive. Flip Flop Relay playback between two Radius 3000 CD/MP3 Players. Built-in MIDI output and input remapping RADIUS-CASE Compatible with: Radius. Change device name (Radius 3000 A-H) for easy set-up. Link Mode: Gives the user the ability to plug in a USB Hard Drive into one Radius 3000 yet operate it from additional USB linked Radius 3000 players (up to additional 2 units). Dimensions (LxWxH): 10.5 x 14 x 4.25 / 265x356x106 mm. Weight: 8 lbs. / 3.6 kgs. *Supports most WAV files (PCM 1411 Kbps). May not be compatible with 1411.2 Kbps WAV files.

INCLUDED IN BOX!

pr ofessional digit al pr oducer contr oller

AU D I O S OFT WARE

PCDJ DEX LE SOFTWARE Minimum System Requirements: WINDOWS XP or WINDOWS VISTA (32-bit and 64-bit supported) PIV 1.2 GHz computer (SSE2 CPU), AMD 64 or Greater 1024768 SVGA video DP2 Controller with built-in ASIO soundcard1 Gig RAM (XP), 2 GIG RAM (Vista) 40 MB free on the hard-drive (recommended 200MB)
D P2 F E AT U R E S :. 4 sample buttons per side (Sample length can be adjusted in preference dialog / Audio system setting page (8~30 seconds per sample if the PC hard disk memory size allow). MIDI capable. 4 Hot Cue buttons per side. Seamless Loop. Smart loop. X & Y Parameter adjustment. Scratch effect. Pitch Lock (Tempo Lock) + Pitch Bend. Pitch Adjustment Knob (+/- 4%, +/- 8%, +/- 16%). 2 channel mixer & crossfader. Back panel: USB input, headphone input, microphone input, RCA Outputs
B A S I C S YS T E M R E Q U I R E M E N T S :. Intel Pentium 4 1GHz processor, Intel Centrino Mobile Technology 1.6GHz, or above. Intel Celeron Processor NOT recommended. Microsoft Windows XP or Vista. DirectX 9 or above. Windows Media Player 9 or above. 512MB RAM. 250MB disk space (200MB for cache). Microsoft DirectSound and ASIO compatible sound card R E CO M M E N D E D S YS T E M R E Q U I R E M E N T S :. Intel Pentium 4 2.4GHz processor, Intel Centrino Mobile Technology 1.6GHz, or above. Microsoft Windows XP or Vista. DirectX 9 or above. Windows Media Player 9 or above. 1GB RAM. 550MB disk space (500MB for cache). Microsoft DirectSound and ASIO compatible sound card
D I M E N S I O N S & W E I G H T:. Dimensions (LxWxH): 19 x 5.25 x 5.25 / 482x132x133mm 3 rack spaces. Weight: 5 lbs. / 2.1 kgs.

V M S4

( Velo city M idi Sta t i o n )
pr ofessional midi sound mixing st ation
G E N E R A L F E AT U R E S : Midi Controller with 4 USB / Analog selectable MIDILOG (Midi & Analog) channels All audio control faders, knobs, switches, and buttons smoothed eliminates popping, wiper noise, and zipper noise On/off soft startup and turnoff Gain/treble/mid/bass EQ on all MIDILOGTM channels 2 phono/line selectable analog channels Two microphone channels with illuminated on/off switches and gain/treble/mid/bass EQs On/off cueing on each MIDILOGTM channel Split cueing headphones with rotary mix control Illuminated rubber knobs for ease of use in dark environments Solid 1.6mm thick faceplate for extra durability Panel mounted rotary knobs Full analog mixer operation if the computer crashes or with external power supply Innofader replaceable crossfader compatible (sold separately) Crossfader curve control Crossfader assign and reverse Q-Start crossfader controlled startup for 2 external audio players User replaceable channel faders Master and Booth outputs with L/R balance Balanced Master outputs 12 position stereo master output VU meter

AUDIO GE NIE P RO

USB audio int er face
Import Audio Using These Programs.
Windows: MME, Audition Macintosh: Garage Band, IMovie, Audio Hijack Pro, Sound Studio,
for CD/Turntable to PC Interface

VE R S AP OR T

Windows: MME, MS DirectSound, Steinberg ASIO & Audition Macintosh: Garage Band, IMovie, Audio Hijack Pro, Sound Studio, Sound Manager (OS9)
V E R S A P O R T M A I N F E AT U R E S :. 16-bit/48 kHz AD/DA converter. USB 1.1 compliant. Mic level knob. Monitor level knob. Line/ phono selector. Headphone & Mic jack. 2 channel - 2 input & 2 output. RCA analog connections. USB bus - powered, adapter-free. Dimensions (LxWxH): 130 x 120 x 40 / v4.72 x 5.1x 1.57. Weight: 0.33 lbs. / 0.15 kgs
The recording time is limited only by your available hard drive space, also file formats vary depending on OS.

POC K E T R E COR D

pr ofessional SD r ecor der
- Portable high quality digital audio recorder. Specially designed for voice & audio recording P O C K E T R E CO R D F E AT U R E S :. Stereo built-in condenser microphones. Support high quality 44 KHz wav and MP3 recording formats. Stereo audio inputs. Switch to microphone, guitar & line-in recording sources. Volume control for input and output level adjustment. Stereo earphone jack. Built-in 128Mb flash memory. Equipped with an expanded memory slot for an SD card. USB port for computer connection and DC power in. Works with either two AA batteries or a DC 5V (NOT INCLUDED). Dimensions (LxWxH): 6. x 3.5 x 1 / 155 x 84 x 28mm. Weight: 6 lbs. / 2.5 kgs.

MEDIA PLAYBACK SOLUTIONS

M -52 U S B M I XE R / So u n d C a r d
pr ofessional19, 1U USB rack mount mixer
B u i l t f o r i n s t a l l a t i o n s i n c l u b s , b a r s o r w h e r e e ve r n o t m u c h s p a c e i s av a i l a b l e , b u t t h e m a x i m u m i n f u n c t i o n a l i t y i s n e e d e d. F E AT U R E S : 2 channel, USB rackmount mixer 2-channel, USB single rack mount mixer EQ adjustment for each channel Input matrix 1 microphone input 2x phono/line input (switchable) 2x line input Balanced XLR outputs 1 RCA master and 1 zone output Built-in full duplex USB soundcard - Input and Output simultaneously 2x USB inputs for USB sticks, HDD, SD-card readers etc. 3 selectable crossfader curve presets Gain per channel Mini jack input on the front Microphone talkover function LED peak levels on each channel Crossfader Cueing Dimensions (LxWxH): 19x5.25x1.75 / 483x133x44 mm Weight: 4 lbs. / 1.7 kg

C K- C A S E. Compatible with - CK-800 - CK-1000
R E A R PA N E L F E AT U R E S :. XLR Balanced. Digital Output (S/PDIF). 2 additional line inputs. Mic input (XLR or 14 input). Multi-voltage Switch: 115V/60Hz or 230V/50Hz. Power On/Off button. Dimensions (LxWxH): 17.75 x 11.25 x 4.5 / 450x285x110mm. Weight: 13 lbs. / 6 kgs.

CDI 300 MP3

M P3 F E AT U R E S :. Plays MP3, CD & CD-R discs. Display shows track (song) title and artist when a MP3 disc is played. Advanced cueing with track searching by frame (not by each second). Quick MP3/CD recognition. Folder Search M A I N F E AT U R E S :. Digital Scratching 2.0 (Accurate Scratching). Visual marker display: Reference point to view where the disc is playing. Anti Shock (10 sec.). Seamless loop. Fader Q Start. 3 flash start buttons with (5 second sample each button). Tempo Lock. Auto BPM Counter. Hyper Pitch (+/- 4%, +/-8%, +/-16%, +/-100%). Digital output (S/PDIF). Dimensions (LxWxH): 13.75 x 9.75 x 4.25 / 348x246x106 mm. Weight: 7 lbs. / 3.3 kgs.
*May var y depending on bit rate of your MP3 f iles.

C D I 300 MP3 SYSTEM

. 2 x CDI 300 MP3 CD Players. 1 x Q-D6 Mixer. Case & Component cables included
V E LO C I T Y M P3 F E AT U R E S :. Plays MP3, CD & CD-R discs. Quick MP3/CD recognition. Display show track listing and artist when a MP3 disc is played. Advanced cueing with track searching by frame (not by each second). Advanced Track Search by track (song) title or by Folder Search. Fine Tune B.P.M. adjustment. Cue Point. Advance Track Launch V E LO C I T Y M P3 F E AT U R E S :. PowerTouch** , Touch sensitive interactive jog wheels (**U.S. & foreign patents pending). Digital Scratching 2.0 (Accurate Scratching). 2 Scratching modes: Digital Scratch mode, Beat Juggle mode. 9 On-board FX: Scratch, Filter, Echo, Trans, Skid, Phase, Flanger, Pan, Bop. Effect layering. Digital B.P.M. counter: keeps digital FX in sync with music. 6 Preset Parameters settings for each FX. Tempo Lock (Master Tempo). Parameter Ratio & Time adjustment knobs. Hyper Pitch (+/-4% up to +/-100%). 3 Flash Start Sampler Buttons per side (7 second sample per button with or without a CD in drive). Slot Load Dual CD Player. Digital Anti-shock memory. Instant start. Seamless loop. Fader Q Start. Reverse play. Digital output - S/PDIF. Volume control between music and sampler. FX MIX. Store 384 cue points or samples. Flip Flop (Relay playback between two decks). Dimensions MAIN UNIT: 19 x 10 x 3.5 (2 rack spaces) CONTROL UNIT: 19 x 2 x 7 (4 rack spaces). Weight (total): 16 lbs.

V EL O C I TY

pr ofessional dual mp3 /cd player

PL AY U P TO

O F M P3 M U S I C P E R D I S C *

MC D-7 10

M A I N F E AT U R E S :. Plays MP3, CD & CD-R discs. Fader Q Start. +10 track advance button. -10 back track button. MP3 Folder Search. Auto BPM. Tempo Lock. 20 seconds Anti Shock Protection (per side). Flip Flop (Relay Playback). Pitch Control (+/-4%, +/-8% or +/-16%). Pitch Bend. Advanced cueing with track search by frame. S/PDIF digital output for each player. Bright LCD display Single/Continue and Time viewing. Reads CD and CD-R media. Update firmware via CD-ROM. Dimensions (LxWxH): Player unit: 10 x 19 x 3.5 Controller: 2.5 x 19 x 3.5 (2-spaces). Weight:15 lbs.

DCD - P R O 310 M KI I

pr ofessional dual cd player
M A I N F E AT U R E S. Audio CD & CD-R compatible. Single/Continuous playback. +10 track advance button. Single Repeat mode. Mechanical Anti-Skip Protection. Flip Flop (Relay Playback). Pitch / Frame search jog modes. Pitch Control (+/-4%, +/-8% or +/-16%)
. Pitch Bend. Bright LCD display: Single/Continue and (3) Time viewingmodes. Dimensions (LxWxH):. Player unit: 10 x 19 x 3.5 / 254x482x89mm(2 rack spaces). Controller: 2.5 x 19 x 3.5 / 64x482x89mm (2 rack spaces). Weight:15 lbs./ 7kgs.

MC D- 1 10

pr ofessional mp3 /cd player
M C D -110 M A I N F E AT U R E S. Plays MP3 and CD discs. +10 track advance button. -10 back track button. 20 seconds Anti Shock Protection. Pitch Control (+/-4%, +/-8% or +/-16%). Pitch Bend. Advanced cueing with track search by frame. S/PDIF digital output for each player
. Bright LCD display Single/Continue and Time viewing. Reads CD and CD-R media. Update firmware via CD-ROM. Dimensions (LxWxH): Player unit: 10 x 19 x 3.5 (2-spaces). Weight: 9 lbs.

PRO MIXERS

pr ofessional mp3 mixer

MAIN ADVANTAGES:

. No external hard drives. No expensive laptops. No extra MP3 players. No complicated software to learn. Supports up to 4GB SD Card

Q-SD MAIN FEATURES:

. SD card slot for full functioning MP3 player (reads SD cards up to 4GB). 4-channel, 19-inch Professional SD DJ mixer. 2 Phono, 4 Line, 4 Aux & 2 Mic inputs. Folder & Track knob selector. Big LCD display with back-light. Crossfader start control for CD player. Mic input and master output trim control. Tempo Lock. Fader Q Start compatible (with select American Audio CD players). Balanced XLR outputs. DJ microphone with volume, treble, bass and talkover control. Gain, treble, mid & bass control for each channel (-30 dB Rotary Kills). Advance MP3 Track Selection. Recessed back panel. Mini plug input on face of mixer for use with MP3 players (standard 3.5mm plug). Headphone jack on face of mixer. Cue mixing, cue level and master level control. Zone output control. Seamless Loop. Auto BPM counter. Stream Flow LED meters. Fully adjustable crossfader curve. Volume, treble and bass control for each mic. Trim output adjustment on rear. Mic attenuator control on rear panel. Pitch Blend (+/-4%, +/-8%, +/-16%, +/-60%). Power: Switchable AC 115/230V, 60/50Hz, 18W. Dimensions (LxWxH): 19x 7x 4.5 / 482.6 x 177 x 109.6mm - 4 rack spaces. Weight: 9 lbs. / 4 kgs. Q-SD does not accept SDHC-cards.

Q-R E COR D

pr ofessional USB mp3 dj mixer
USB Flash Drive For Full Functioning MP3 Playback & Record!
Q - R E CO R D M A I N FE AT U R E S. Professional 19-inch 4-channel mixer. USB Flash drive for full functioning MP3 playback & record. 2 Phono, 4 Line, 4 Aux & 2 Mic inputs. Fader Q Start compatible (with select American Audio CD players). Balanced XLR outputs. Mic volume, treble, bass and talkover control. Gain, treble, mid & bass control for each channel (-30 dB Rotary Kills). MP3 recorded at 256kbps. Recessed back panel. Mini plug input on face of mixer for use with MP3 players *(standard 3.5mm plug) *MP3 player not included. Headphone jack on face of mixer. Cue mixing, cue level and master level control. Zone output control. Stream Flow LED meters. Trim output adjustment on rear. Mic attenuator control on rear panel. Power: Switchable AC 115/230V, 60/50Hz, 18W. Dimensions (LxWxH): 19x 7x 4.25 / 482.6 x 177 x 109.6mm - 4 rack spaces. Weight: 8.5 lbs./3.8 kgs.

Q -D1 PR O

pr ofessional mixer
Q - D1 PR O M A I N FE AT U R E S. 2 band EQ w/input gain control per channel. High level master output, high current phones output. Power on/off muting. Low sound leakage cross fader. Low distortion (0.0028%), low noise (S/N=112dB). CD play control by cross fader. Record out. USB Device Port (USB device not included) with Play/ Pause Next andPrevious Buttons. Balanced TRS Outputs. Power Source: AC 9V, 1000mA. Dimensions (WxDxH): 8.62 x 10.04 x 3.94 / 219x255x100mm. Weight: 5 lbs. / 2.3 kgs.

Q -D 1 M KI I

Q - D1 M A I N FE AT U R E S. 2 Phono, 2 Line, 1 Mic inputs. Q-Start. Gain, treble and bass control for each channel. Master, Microphone and Cue Level volume control. Cue monitoring between channels. 1/4 jacks for Mic & Phono input. 9V AC power supply included. Dimensions (LxWxH): 9.5 x 7.5 x 4. Weight: 4 lbs.

Q -D 6

pr ofessional 10-inch mixer
Q-D6 M A I N F E AT U R E S. 3-channel Pro DJ Mixer. 2 Phono, 3 Lines, 2 Aux & 1 Mic input. Mini plug input on face of mixer for use with MP3 players & satellite receivers. Balanced Outputs. Fader Q Start Compatible. Gain, Treble, Mid & Bass control for each Ch. (-26 dB Rotary Kills). DJ Mic with Volume, Treble, Bass and Talkover control. Stream flow LED Master Level meters. Cue Mixing, Cue Level and Master Level Control. Extremely clean signal to noise ratio. Dimensions (LxWxH): 12.25 x 10x 3.25. Weight: 7 lbs.

Q-D5 M K II

Q -D5 MKII M A I N F E AT U R E S. 2 Phono, 2 Lines, 2 Aux & 1 Mic input. Optical Crossfader (tested over 1 million times)*. Balanced XLR outputs. Q-Start. Cross Fader curve knob (short to long crossfade) with reverse crossfade button. Independent curve for channels 1 & 2 (short to long curve) with reverse button. Gain, Treble, Mid & Bass control for each channel. -30 dB Rotary Kills for Treble, Mid & Bass. 100% cut buttons for Treble, Mid & Bass. Dimensions (LxWxH): x 12.25 x 10 x 3.25. Weight: 7 lbs.

M822FX

M-Series PA Mixer

PA PACK 1X

M822F X PA Mixer Package
I N C LU D E S : 1- M 2 F X 2 -X S P 10A ( s t a n d s n o t i n c l u d e d ) XSP 10A Main Features :. 10-inch 2-way Powered Speaker. Dual Amplifiers *LF/HF 200 Watt Total. 1-inch Compression Driver. Time Aligned Electronic Crossover. Flyable or Stand Mountable. Full grille. Built-in mixer with 1 Line input; 1 Mic input; Treble & Bass Control; Channel and Master Volume. XLR through output. Dimensions (LxWxH): 14 x 11 x 19 / 355x280x480mm. Weight: 31 lbs. / 14 kg. Speaker Specifications :. Frequency Response: 20Hz - 20KHz. Crossover: 3.5k. Nominal Dispersion: 90 x 50 (HXV) Amplifier Specifications :. Line: -20dB(100mV). Microphone: -40dB(10mV) *Low Frequency / High Frequency
M4 F X F E AT U R E S : Controls. 4 mono & 4 stereo channels input. Stereo Main output & ALT 3/4 output. Trim with Peak LED, HPF, 3-band EQ, 1 AUX with Pre/Post switch, 1 EFX, PAN, Mute & PFL switch for mono input. Trim with Peak LED, HPF (CH5-8). 3-band EQ, 1 AUX with Pre/Post switch, 1 EFX, BAL, Mute & PFL for stereo input. Main L/R with AFL switch, ALT3/4 with AFL, To Main switch, AUX Send, EFX send, AUX return & EFX return. Tape with PFL switch, HP/Control Room & Phantom Power. 24-bit DSP effect 100 presets, EFX on/off & EFX level Input Connectors:. 6 XLR MIC/INPUTS. XLR & 1/4 phone jack balanced & 1/4 phone jack for Insert on mono input. XLR & 1/4 phone jack for stereo (CH5-8) 1/4 phone & phono jack for stereo input. 1/4 phone jack for stereo return & phono jack for Tape Output Connectors:. 1/4phone jack for Main, ALT 3/4, AUX Send, EFX Send, Control Room & Headphone. Phono jack for Tape & 1/4 phone jack for Footswitch Indicator:. Peak for each mono channel, PFL, level meter, phantom power & DSP program Specifications M1224FX. Weight (Net): 3.4 kg. Dimensions: (W x H x D) 328 x 420 x 65 mm

M1224FX

PA PA CK 2X
M1224F X PA Mixer Package
I N C LU D E S : 1- M4 F X 2 -X S P 12 A 2 -S P S -1B XSP 12A Main Features :. High-powered 12-inch, 2-way Powered Speaker. Dual Amplifiers *LF/HF 300 Watt Total. Neodymium components. 1.75 compression driver. Time Aligned Electronic Crossover. Flyable or Stand Mountable. Full grille. Built-in mixer with 1 Line input; 1 Mic input; Treble & Bass Control; Channel and Master Volume. XLR through output. Dimensions (LxWxH): 16 x 12 x 23 / 405x305x585mm. Weight: 44 lbs. / 20 kg. Speaker Specifications :. Frequency Response: 20Hz - 20KHz. Crossover: 3.8k. Nominal Dispersion: 90 x 50 (HXV) Amplifier Specifications :. Line: -20dB(100mV). Microphone: -40dB(10mV) * Low Frequency / High Frequency

M16 24FX

M4 F X F E AT U R E S : Controls. 8 mono & 4 stereo channels input. Stereo Main output & ALT 3/4 output. Trim with Peak LED, HPF, 3-band EQ, 1 AUX with Pre/Post switch, 1 EFX, PAN, Mute & PFL switch for mono input. Trim with Peak LED, HPF (CH9-12). 3-band EQ, 1 AUX with Pre/Post switch, 1 EFX, BAL, Mute & PFL for stereo input. Main L/R with AFL switch, ALT3/4 with AFL, To Main switch, AUX Send, EFX send, AUX return & EFX return. Tape with PFL switch, HP/Control Room & Phantom Power. 24-bit DSP effect 100 presets, EFX on/off & EFX level Input Connectors:. 10 XLR MIC/INPUTS. XLR & 1/4 phone jack balanced & 1/4 phone jack for Insert on mono input. XLR & 1/4 phone jack for stereo (CH9-12) 1/4 phone & phono jack for stereo input. 1/4 phone jack for stereo return & phono jack for Tape Output Connectors:. 1/4phone jack for Main, ALT 3/4, AUX Send, EFX Send, Control Room & Headphone. Phono jack for Tape & 1/4 phone jack for Footswitch Indicator:. Peak for each mono channel, PFL, level meter, phantom power & DSP program Accessories:. 19 standard rack mountable (optional) Specifications M1624FX. Weight (Net): 5.6 kg. Dimensions: (W x H x D) 436 x 420 x 65 mm

PA PACK 3 X

M1624F X PA Mixer Package
I N C LU D E S : 1- M4 F X 2 -S P S -1B 2 -X S P 10A 2 -X S P 15A 2 - PX W 18 P PXW 18P Main Features :. 18 powered Sub. 800 watts max power. Dimensions: (LxWxH): 27 x 27 x 32 / 686 x 686 x 813 mm. Weight: 171 lbs. / 78 kgs. XSP 10A Main Features :. 10-inch 2-way Powered Speaker. Dual Amplifiers *LF/HF 200 Watt Total. 1-inch Compression Driver. Dimensions (LxWxH): 14 x 11 x 19 / 355x280x480mm. Weight: 31 lbs. / 14 kg. XSP 15A Main Features :. High-powered 15-inch, 2-way Powered Speaker. Dual Amplifiers *LF/HF 400 Watt Total. Built-in mixer with 1 Line input; 2 Mic inputs; Treble & Bass Control; Channel and Master Volume. Dimensions (LxWxH): 17 x 15 x 27 / 430x380x685mm. Weight: 57 lbs. / 26 kg. * Low Frequency / High Frequency

PRO AMPLIFIERS

VX SERIES Controls At Your Fingertips: Input Sensitivity Filters Output Configuration

VX-1000

VX-1500
550W RMS per channel 500W RMS per channel 330W RMS per channel 1100W RMS per channel 1000W RMS per channel
750W RMS per channel 700W RMS per channel 450W RMS per channel 1500W RMS per channel 1400W RMS per channel
Total Harmonic Distortion (THD): Less than 0.5% (20Hz-20kHz, @ 8 Ohms) Input Sensitivity & Impedance: 1.0v rms (0 dBv) (@ 4 Ohms) Dimensions & Weight: Height: 3.5 (88mm) Width: 19 (483mm) Depth: 16.5 (429mm) Weight: 40 lbs. (18.5 kg)
Total Harmonic Distortion (THD): Less than 0.5% (20Hz-20kHz, @ 8 Ohms) Input Sensitivity & Impedance: 1.0v rms (0 dBv) (@ 4 Ohms) Dimensions & Weight: Height: 3.5 (88mm) Width: 19 (483mm) Depth: 16.5 (429mm) Weight: 45 lbs. (18.5 kg)

Total Harmonic Distortion (THD): Less than 0.5% (20Hz-20kHz, @ 8 Ohms) Input Sensitivity & Impedance: 1.0v rms (0 dBv) (@ 4 Ohms) Dimensions & Weight: Height: 3.5 (88mm) Width: 19 (483mm) Depth: 19.5 (495mm) Weight: 52 lbs. (23.5 kg)
Frequency Response: 3dB, 1W RMS 8 ohms (20Hz - 20kHz)
Signal to Noise Ratio: Less than 95 dB , unweighted (@ 8 ohms full power) Slew Rate: 15v/usec
Signal to Noise Ratio: Less than 95 dB , unweighted (@ 8 ohms full power) Slew Rate: 15v/usec Damping Factor: 300 (@ 8 Ohms)
Signal to Noise Ratio: Less than 95 dB , unweighted (@ 8 ohms full power) Slew Rate: 15v/usec Damping Factor: 500 (@ 8 Ohms)
Damping Factor: 300 (@ 8 Ohms)
Protection Circuit: DC output protection, Overload protection, High Temp protection, Short circuit protection, Current Inrush protection, Soft start-up protection Power Consumption: 5A @ 120V AC (@ 8 Ohms) Fan: 2-speed fan
Modes: Stereo, Parallel or Bridge Mono

VX-2500

Output Power: 2 ohms, 1 khz 1% THD 4 ohms, 1 khz 1% THD 8 ohms, 1 khz 1% THD (Bridged Mode, mono) 4 ohms, 1 khz 1% THD 8 ohms, 1 khz 1% THD
1400W RMS per channel 1200W RMS per channel 750W RMS per channel 2800W RMS per channel 2400W RMS per channel
QUALITY, AFFORDABLE & RELIABLE POWER AMPLIFIERS FOR THE WORKING PROFESSIONAL.

VLP300

Output Power 4 ohms, 1 khz 0.1% THD 8 ohms, 1 khz 0.1% THD (Bridged Mode, mono) 8 ohms, 1 khz 0.1% THD 150W RMS per channel 100W RMS per channel

VLP600

300W RMS per channel 200W RMS per channel 600W RMS per channel

VLP1500

750W RMS per channel 500W RMS per channel 1500W RMS per channel

300W RMS per channel

Total Harmonic Distortion (THD) 20Hz-20kHz, @ rated output Less than 0.1% power, 8 ohms Impedance Balanced / Unbalanced Dimensions & Weight Height Width Depth Weight Frequency Response 1dB, 1W RMS 8 ohms

Less than 0.1%

20K Ohms / 10K Ohms

20K Ohms / 10KOhms

1.75 (44cm) 19 (48.3cm) 13.25 (33.6cm) 24 lbs (11 kg)
3.5 (88cm) 19 (48.3cm) 14 (36cm) 33 lbs. (15kg)
3.5 (88cm) 19 (48.3cm) 14 (36cm) 42 lbs. (19kg)

20Hz - 20 kHz

Slew Rate 15v/usec Damping Factor @ Cooling System 2 individual fans Special Features High/Low Pass Filter Input Sensitivity Selector Ground Lift
15v/usec individual fans High/Low Pass Filter Input Sensitivity Selector Ground Lift Limiter
NOTE - 1 Rackspace = Approx. 1.75

V3001plus

Output Power 2 ohms, 1 khz 1% THD 1020W RMS per channel 4 ohms, 1 khz 1% THD 670W RMS per channel 8 ohms, 1 khz 1% THD 410W RMS per channel (Bridged Mode, mono) 4 ohms, 1 khz 1% THD 2050W RMS per channel 8 ohms, 1 khz 1% THD 1360W RMS per channel Total Harmonic Distortion (THD) 20Hz-20kHz, @ rated output Less than 0.1% power, 8 ohms Input Sensitivity & Impedance @ rated output power, 4 ohms 1.0v rms (0 dBv) Dimensions & Weight Height 3.5 (88cm) Width 19 (48.3cm) Depth 15.9 (40.5cm) Weight 31 lbs. (14kg) Frequency Response 10Hz - 40 kHz.5dB, 1W RMS 8 ohms 3dB, 1W RMS 8 ohms 20Hz - 20 kHz Hum & Noise 100 dB, unweighted Below rated output, 8 ohms Signal to Noise Ratio @ 4 ohms full power unweighted, 60 dB A weighted Slew Rate 25v/usec Damping Factor @ Protection Circuit DC output protection Overload protection Short circuit protection On & Off protection Special Features Sub-Woofer Crossover Contractor Smart Feature** Limiter Power Consumption @ rated output power, 8 ohms 10A @ 120V AC Turn-On Thump Protection Yes Cooling System Dual 2 speed fans & heatsink

Removable Screw-On Cable

(HP 900 model only)
Includes 1/4 Right Angle & Straight 1/4 Gold Connectors
(HP 900 & HP 700 Only HP 500 includes 1/4 Right Angle Only)
Includes Semi Hard Transport Case With Shoulder Strap
Includes A Pair Of Replacement Earpads
(HP 900, HP 700 & HP 500)

H P 700

H P M A I N F E AT U R E S. Comfortable, sturdy high-powered headphones. Ultra dynamic range with great sounding high and lows. Flexible housing design allows for double or single ear monitoring; folds up for easy transport. Input: Mini plug with two screw-on 1/4 adapters (Right Angle & Straight plugs). Includes headphone bag. Cord Length: 9 feet/3 meters

H P 55 0

H P M A I N F E AT U R E S. Comfortable, sturdy high powered headphones. Includes 1 set of extra earpads and a headphones bag. Flexible housing design allows for double or single ear monitoring; folds up for easy transport. Replaceable earpads - Easy to snap on. Input: Mini plug with right angle 1/4 adapter

H P 20 0

dj headphones
HP 200 M A I N F E AT U R E S. Comfortable, light weight headphones. High output in a compact design. Flexible housing design; folds up for easy transport. Input: Mini plug with right angle 1/4 adapter. Cord length: 6 ft. / 2 meters
Includes 1/4 Right Angle Adapter

SOUND REINFORCEMENT

PXW 18P

power ed sub woofer

P W X 18 P S P E C I F I C AT I O N S. 18 Powered Sub. 800 watts max power. Pole mount. Fan cooled. XLR inputs & outputs. Level Control. Heavy duty castor wheels. Weight: 17 lbs. / 78 kgs. Dimensions: (LxWxH) 27 x 27 x 32 / 686 x 686 x 813mm

PXW 15P

P W X 15 P S P E C I F I C AT I O N S. 15 Powered Sub. Fan Cooled. 500 watts max power. Heavy duty castor wheels. Pole Mount. Level Control. Weight: 130 lbs. / 59 kgs. Dimensions: (LxWxH) 27 x 21 x 27 / 686 x 534 x 686mm

D LS -1 5P

power ed speaker
D L S -15 P S P E C I F I C AT I O N S. High Powered 15-inch, 2-way speaker. Die cast woofer with 3-inch voice coil. High compression 1.75 driver. Built-in high-powered amplifier system. ABS nylon fiber cabinet with handle. One XLR & one RCA line input. Two microphone inputs (XLR & 1/4 TRS) with separate microphone volume control. Treble, bass and volume output control. Trapezoidal design. Flyable & stand mountable. Floor monitor brackets included. 120v/220V switchable. Sensitivity: 109 dB/m/w. Dimensions (LxWxH): 13.6 x 16.5 x 26.4. Weight: 61 lbs.

D L S-1 5

dj speaker
D L S -15 S P E C I F I C AT I O N S. High Powered 15-inch, 2-way speaker. Die cast woofer with 3-inch voice coil. High compression 1.75 driver. ABS nylon fiber cabinet with handle. Speakon line input. Trapezoidal design. Flyable & stand mountable. Floor monitor brackets included. Sensitivity: 109 dB/m/w. Dimensions (LxWxH): 13.6 x 16.5 x 26.4. Weight: 55 lbs.

APX -B

speaker carr y bag
A PX- B F E AT U R E S. Rugged speaker bag with rollers, adjustable handle & heavy duty zipper. Move speakers with ease. Fits: DLS-15, DLS-15P, APX-152, APX-Power Pro, PXI Series & various other brand speakers

Z-APX/H

. Heavy duty eye-hook for suspending speakers

Z-APX/B

. Heavy duty bolt for securing speakers
XSPSERIES POWERED SPEAKERS

Designed

LIVE SOUND

XSP-8A

XSP-8A: Main Features :. 8-inch, 2-way Powered Speaker. Dual Amplifiers *LF/HF 100 Watt Total. Time Aligned Crossover. ABS nylon fiber cabinet with handle. Flyable or Stand Mountable. Full grille. XLR Mic/Line input with Volume Control. Dimensions (LxWxH): 11.5 x 9 x 16.5 / 290x230x420mm. Weight: 18 lbs. / 9 kg. Speaker Specifications :. Frequency Response: 20Hz - 20KHz. Crossover: 3.3k. Nominal Dispersion: 90 x 50 (HXV) Amplifier Specifications :. Line: -20dB(100mV). Microphone: -40dB(10mV) *Low Frequency / High Frequency

XSP-10A

XSP-10A: Main Features :. 10-inch 2-way Powered Speaker. Dual Amplifiers *LF/HF 200 Watt Total. 1-inch Compression Driver. Time Aligned Electronic Crossover. Flyable or Stand Mountable. Full grille. Built-in mixer with 1 Line input; 1 Mic input; Treble & Bass Control; Channel and Master Volume. XLR through output. Dimensions (LxWxH): 14 x 11 x 19 / 355x280x480mm. Weight: 31 lbs. / 14 kg. Speaker Specifications :. Frequency Response: 20Hz - 20KHz. Crossover: 3.5k. Nominal Dispersion: 90 x 50 (HXV) Amplifier Specifications :. Line: -20dB(100mV). Microphone: -40dB(10mV) *Low Frequency / High Frequency

XSP-12A

XSP-12A: Main Features :. High-powered 12-inch, 2-way Powered Speaker. Dual Amplifiers *LF/HF 300 Watt Total. Neodymium components. 1.75 compression driver. Time Aligned Electronic Crossover. Flyable or Stand Mountable. Full grille. Built-in mixer with 1 Line input; 1 Mic input; Treble & Bass Control; Channel and Master Volume. XLR through output. Dimensions (LxWxH): 16 x 12 x 23 / 405x305x585mm. Weight: 44 lbs. / 20 kg. Speaker Specifications :. Frequency Response: 20Hz - 20KHz. Crossover: 3.8k. Nominal Dispersion: 90 x 50 (HXV) Amplifier Specifications :. Line: -20dB(100mV). Microphone: -40dB(10mV) * Low Frequency / High Frequency

XSP-15A

XSP-15A: Main Features :. High-powered 15-inch, 2-way Powered Speaker. Dual Amplifiers *LF/HF 400 Watt Total. Neodymium components. 1.75 compression driver. Time Aligned Electronic Crossover. Flyable or Stand Mountable. Full grille. Built-in mixer with 1 Line input; 2 Mic inputs; Treble & Bass Control; Channel and Master Volume. XLR through output. Dimensions (LxWxH): 17 x 15 x 27 / 430x380x685mm. Weight: 57 lbs. / 26 kg. Speaker Specifications :. Frequency Response: 20Hz - 20KHz. Crossover: 4.8k. Nominal Dispersion: 90 x 50 (HXV) Amplifier Specifications :. Line: -20dB(100mV). Microphones: -40dB(10mV) *Low Frequency / High Frequency

XSPSERIES PASSIVE SPEAKERS

XSP-10

XSP-12

XSP-15

Designed for LIVE SOUND
XSP-8: Features :. Passive 8-inch, 2-way speaker. Die cast woofer with 2-inch (50mm) voice coil, 8 Ohms. High compression 1-inch (25mm) Titanium Diaphragm Driver. ABS nylon fiber cabinet with handle. Flyable or Stand Mountable. Full grille. Speakon In/Out connectors. Dimensions (LxWxH): 11.5 x 9 x 16.5 / 290x230x420mm. Weight: 18 lbs. / 8 kgs. XSP-10: Features :. Passive 10-inch, 2-way speaker. Die cast woofer with 2-inch (50mm) voice coil, 8 Ohms. High compression 1.25-inch (34mm) Titanium Diaphragm Driver. ABS nylon fiber cabinet with handle. Flyable or Stand Mountable. Full grille. Speakon In/Out connectors. Dimensions (LxWxH): 14 x 11 x 19 / 355x280x480mm. Weight: 31 lbs. / 10.7 kgs. XSP-12: Features :. Passive 12-inch, 2-way speaker. Die cast woofer with 2.5-inch (65mm) voice coil, 8 Ohms. High compression 1.25-inch (34mm) Titanium Diaphragm Driver. ABS nylon fiber cabinet with handle. Flyable or Stand Mountable. Full grille. Speakon In/Out connectors. Optional APX-B Speaker Transport Bag. Dimensions (LxWxH): 16 x 12 x 23 / 405x305x585mm. Weight: 37 lbs. / 20 kgs. XSP-15: Features :. Passive 15-inch, 2-way speaker. Die cast woofer with 3-inch (75mm) voice coil, 8 Ohms. High compression 1.75-inch (44mm) Titanium Diaphragm Driver. ABS nylon fiber cabinet with handle. Flyable or Stand Mountable. Full grille. Optional APX-B Speaker Transport Bag. Speakon In/Out connectors. Dimensions (LxWxH): 17 x 15 x 27 / 430x380x685mm. Weight: 49 lbs. / 22 kgs.

CASES & ACCESSORIES

ETL C -8 X 4
E T LC- 8X4 M A I N F E AT U R E S. 19 inch rack mount: 8 spaces Top, 4 spaces Bottom. Sturdy plywood construction. Convenient, easy to carry handles. Rugged & road worthy. Detachable cover / lid (durable nylon with polyethylene center). Dimensions (LxWxH): 20 x 20 x 17. Weight: 18 lbs. Equipment sold separately

USB LIGHT

M A I N F E AT U R E S. Light for mixers and control consoles

GNL-14

M A I N F E AT U R E S. GNL-14, Gooseneck Light allows you to perform in dimly lit areas. 14-inch flexible gooseneck fits the American Audio mixers with BNC connection. Comes with one lamp. Replacement lamp:Model:ZB-GNL. Connection:12V DCBNC

TL C -8 X 1 4

T LC- 8X14 M A I N F E AT U R E S. An easier way to haul around your audio set ups, while keeping your gear organized and secure. A rackmount case on wheels thats designed to hold a complete DJ audio setup-from mixers and CD players to amplifiers and everything in between. 19-inch rack mount - 8 spaces Top, 14 spaces Bottom. Adjustable top rack. Made of lightweight, durable plastic. Rugged road worthy construction: 3 detachable lids (top, front and back), metal corners, lock tight latches. Dimensions (LxWxH): 23 x 21.5 x 38. Weight: 56 lbs. (unloaded). Equipment not included