IMPORTANT SAFETY INSTRUCTIONS
GROUNDING OR POLARIzATION If this product is equipped with a polarized alternating current line plug (a plug having one blade wider than the other), it will fit into the outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. If this product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin, it will only fit into a grounding type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding type plug. POWER-CORD PROTECTION - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. OUTDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A. LIGHTNING For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. OVERLOADING Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

OBJECT AND LIQUID ENTRY - Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. SERVICING Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. DAmAGE REQUIRING SERVICE - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power-supply cord or plug is damaged. If liquid has been spilled, or objects have fallen into the product. If the product has been exposed to rain or water. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. If the product has been dropped or damaged in any way. When the product exhibits a distinct change in performance this indicates a need for service. REPLACEmENT PARTS -- W hen replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. SAFETY CHECK - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. WALL OR CEILING mOUNTING The product should not be mounted to a wall or ceiling. HEAT The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
VENTILATION Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturers instructions have been adhered to. POWER SOURCES This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. LOCATION The appliance should be installed in a stable location. NONUSE PERIODS The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.

ANTENNA LEAD IN WIRE GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
ELECTRIC SERVICE EQUIPMENT
GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) NEC NATIONAL ELECTRICAL CODE

Fig. A

Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 4

SAFETY INSTRUCTIONS

I. Read Instructions - All the safety and oper- ating instructions should be read before you perate the system. The safety and o operating instructions should be saved for future reference. 2. eed Warnings - All warnings on the system H and in the operating instructions should be adhered to. 3. ater and Moisture - The player should not W be used near water - for example, near a bath tub, kitchen sink, laundry ub, in a wet t basement or near a swimming pool, etc. 4. entilation - The system should be situated V so that its location or position does not interfere with its proper ventilation. For exam ple, the system should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. 5. eat - The system should be situated away H from heat sources such as radiators, heat registers, stoves, or other appliances (includ ing amplifiers) that produce heat. 6. ower Sources - The system should be conP nected to a power supply only of the type described in the operating instructions or as marked on the system. 7. Servicing - The user should not attempt to service the system beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel. The system should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the system. C. The system has been exposed to rain or water. D. The system does not appear to operate normally or exhibits a marked change in performance.

Line Voltage Selection

The desired voltage may be set with the VOLTAGE SELECTOR switch on the rear panel (using a flat head screw driver). Do not force the VOLTAGE SELECTOR switch as this may cause damage If the VOLTAGE SELECTOR switch does not move smoothly, please contact a quali- fied service technician.

VOLTAGE SELECTOR switch

The serial and model number for this unit is located on the rear panel. Please write down the numbers here and retain for future reference. Model No._____________________________ Serial No._____________________________ Purchase Notes: Date of Purchase_______________________ Dealer Name__________________________ Dealer Address_________________________ __________________________________________ ________________________________________ Dealer Phone__________________________

Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 5

Unpacking

Every CK 800Mp3 System has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your system for any damage and be sure all equipment necessary to operate the system has arrived intact. In the event damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Please do not return the system to your dealer without first contacting customer support.

Introduction

Introduction: Congratulations and thank you for purchasing the American Audio CK 800Mp3 System. This system is a representation of American Audios continuing commitment to produce the best and highest quality audio products possible at an affordable price. Please read and understand this manual completely before attempting to operate your new system. This booklet contains important information concerning the proper and safe operation of your new system. Customer Support: American Audio provides a toll free customer support line, to provide set up help and answer any question should you encounter problems during your initial set up or operation. You may also visit us on the web at www.AmericanAudio.us for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacific Standard Time. Voice: (800) 322-6337 Fax: (323) 582-2941 E-mail: support@americanaudio.us To purchase parts online visit http://parts.americandj.com Caution! There are no user serviceable parts inside this audio system. Do not attempt any repairs yourself, without being instructed to do so by an authorized American Audio service technician. Doing so will void your manufactures warranty. In the unlikely event your audio system may require service, please contact American Audio customer support. Do not discard the packing carton in the trash. Please recycle when ever possible.

Set-Up Precautions

Please be sure to make any connections before plugging the system in to an electrical outlet. All fader and volume controls should be set to zero or minimum position, before the system is switched on. If the system has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch on the system immediately. The arising condensation of water might damage your device. Leave the device switched off until it has reached room temperature. Operating Determinations: When installing this system, please make sure that the device is not exposed or will not be exposed to extreme heat, moisture or dust! Do not operate the system in extremely hot (more than 30/86F) or extremely cold (less than 5C/40F) surroundings. Keep the unit out of direct sunlight and away from heaters. Operate the system only after becoming familiar with its' functions. Do not permit operation by persons not qualified for operating the unit. Most damages are the result of unprofessional opera- tion.

Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 6

Main features

Plays Mp3, CD, and CD-R Discs Auto cue Sleep Mode (c) Selectable Single or Continuous Play 1/75th second frame search Real time cue (Cue on the Fly) Pitch display Digital RCA coaxial output Large bright LCD display can be viewed from wide angles. Fader Q Start Control (a) Digital Anti-Shock Jog Wheel Pitch Bend +/-100% RELAY (Flip-Flop Playback) (b) Aux Input Cue Mixing High output to headphones Seamless Loop (uninterrupted loop playback) 2 Line Level Inputs 3 Band EQ per channel Independent Gains Per Channel Front Access Combo Mic Jack Record Out Extremely clean signal to noise ratio Adjustable Pitch Percentages: +/-4%, +/-8%, and +/-16% Instant Start within 10ms (sound is produced immediately when the PLAY button is pressed)
(a) (b) FADER Q START CONTROL: Set up your CK 800Mp3 as described in the set-up section of this manual. After set up is completed load your players. By moving the mixers crossfader from left to right you can start and pause each players playback functions. For Example, when using the CK 800Mp3 player, if your mixers crossfader is all the way to the left (player one is playing, player two is in cue or pause mode), and you move the fader at least 20% to the right, player two (2) will begin to play. When the crossfader is to the right, and you move it 20% to the left, player one (1) will begin to play. You can create great effects similar to scratching with this feature. After storing cue points on each side of the CD player, different songs may quickly be recalled by moving the mixer crossfader back and forth. New cue points can be easily selected on the CK 800Mp3 player (see setting cue points page 19). Q Start control is easy to use and mastering this feature will help you create amazing effects with your music. RELAY (Flip-Flop): Connect your CK 800Mp3 player as described in the set-up section of this manual. This feature will start the next player once one (1) player has ended. For example, if player one (1) is playing a disc and it ends, player two (2) will instantly begin to play. You may set RELAY to play track to track or disc to disc. For more information on this feature, see RELAY (FLIP-FLOP) on page 25. (when in pause or cue mode). This will lengthen the life of your motor drive and laser. To initialize the player, just press the cue or play buttons.

(c) SLEEP MODE: The CK 800Mp3's laser and pick-up assembly will power down after 15 minutes of inactivity
Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 7
FOR BEST CD-R DISC PLAYBACK RESULTS IN THIS CD PLAYER PLEASE FOLLOW THESE GUIDELINES: 1. High quality CD-R Audio discs (should conform to the standards of the Orange Book 2). 2. Use a high quality bit rate when recording discs. (At least 160kbps) 3. Record discs in the slowest speed possible. (i.e. 2x or 4x speed) 1.Checking the Contents Be sure your CK 800Mp3 was shipped with the following: 1) CK 800Mp3 Professional CD player/mixer. 2) Operating instructions (this booklet). 3) Warranty card.

Set-UP

CAUTION: To avoid severe damage to the unit, be sure the power is off when making connections to the unit.
CAUTION: The CK 800Mp3 will work normally when the unit is mounted with the front panel within 15 degrees of the vertical plane If the unit is tilted excessively, discs may not be loaded or unloaded properly. (Figure 1)

Figure 1

CAUTION: The LCD is designed to be clearly visible within the angles shown in Figure 2. Mount the unit so that the visual angle is within this range.

Figure 2

Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 8
GENERAL Functions and controls

cd player

Figure 3
A. Top unit controls (Figure 3)
1. EJECT FUNCTION - Pressing this will eject the CD. The eject function will only when the unit is in pause or cue mode, this is to prevent accidentally ejecting the disc when in play mode. 2. TIME BUTTON - The TIME button will switch the time value described in the time meter between Elapsed playing time, TRACK Remaining time, and Total remaining time (this is for CDs only). 3. SGL/CTN - This function allows you to choose between single track play or continuous track play (all tracks in order). This function also operates in RELAY (flip-flop) mode, when RELAY is activated. 4. PITCH SLIDER - This slider is used to adjust the playback pitch percentage. The slider is a
set adjustment and will remain set until the pitch slider is moved or the pitch function has been turned off. This adjustment can be made with or without a disc in the drive. The pitch adjustment will remain even if a disc has been removed and will reflect on any other disc loaded into the player. That is to say, if you set a +2% pitch on one disc, remove that disc and insert another, that disc too will have a +2% pitch. The amount of pitch being applied will be displayed in the LCD (16). 5. Pitch ON/OFF Button - This button is used to switch the pitch function on and off. When the button LED is lit the PITCH SLIDER (4) is active. When the button LED is not lit, the PITCH SLIDER (4) is not active. The pitch percentage

Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 9
GENERAL Functions and controls (Cont.)
can be changed between 4%, 8%, and 16%. 4% pitch percentage can be changed between 4%, will allow the least amount of pitch manipulation and 16% will allow the most amount of pitch manipulation. 6. PITCH PERCENTAGE SELECTOR - Press this button to select pitch range percentages of 4%, 8%, and 16%. See adjusting the PITCH SLIDER'S RANGE on page 22. 7. (+) PITCH BEND BUTTON - The (+) pitch bend function creates a momentary BUMP in the CDs BPMs (Beats per minute) while it is playing. This will allow you to match the beats between two playing CDs or any other music source. Remember, this is a momentary function. When you remove your finger from this button, the BPMs will automatically return to Pitch sliders (4) selected pitch. Holding down this button will give a maximum of +16% pitch. (-) PITCH BEND Button - The (-) pitch bend function creates a momentary Slow Down in the CDs BPMs (Beats per minute) while it is playing. This will allow you to match the beats between two playing CDs or other playing music source. Remember, this is a momentary function. When you remove your finger from the pitch button, the BPMs will automatically return to Pitch sliders (4) pitch value. Holding down this button will give a maximum of -16% pitch. Use this function to slow to another playing music source. Be sure to notice that this function is a momentary pitch adjustment, for a more precise adjustment use the pitch slider (4) to match the BPMs with another playing music source. 8. RELOOP BUTTON - If a SEAMLESS LOOP has been made (see setting a SEAMLESS LOOP on page 20), but the CD Player is not actively in SEAMLESS LOOP mode (a loop is not playing), pressing the RELOOP button will instantly reactivate the SEAMLESS LOOP mode. To exit the loop, press the OUT button (10). LOOP will appear in the LCD DISPLAY (16) when the RELOOP function is available. 9. JOG WHEEL/EFFECTS PLATTER - This wheel has two functions;

A. B.

CD PLAYER
The jog wheel will act as a frame search control when the CD is in pause or cue mode, allowing you to set a cue point. The wheel also works as a pitch bend during Playback. Turning the wheel clockwise will increase the pitch percentage up to 100%, and turning the wheel in the counter-clock- wise direction will decrease the pitch percentage down to -100%. The pitch bend will be determined on how long you turn the jog wheel continuously.
10.Out Button - This button is used to set the ending point of a loop. A loop is started by pressing the IN BUTTON, and pressing the OUT BUTTON to set the loop ending point. The loop will continue to play until the OUT BUTTON is pressed once again. SEAMLESS LOOP IN BUTTON - cue ON THE FLY - This function allows you to set a CUE POINT (see CUE POINT page 19) without music interruption (on the fly). This button also sets the starting point of a seamless loop (see SEAMLESS LOOP). 11.PLAY/PAUSE Button - Each press of the PLAY/PAUSE Button causes the operation to change from play to pause or from pause to play. While in play mode the blue play LED will glow, and while in pause mode the blue play LED will flash. 12. CUE - Pressing the CUE button during playback immediately pauses playback and returns the track to the last set cue point (see setting a CUE POINT, page 19). The red CUE LED will glow when the unit is in cue mode The LED will also flash every time a new CUE POINT is set. The CUE button can be held down to momentarily play the CD. When you release the CUE button it instantly returns to the CUE POINT. 13. +10 TRACK SKIP - This button allows you to skip ahead by 10 tracks. Example: if you are at Track #1, pressing this button will skip you to Track #11, press the button again, it will skip to Track #21. If there are not that many tracks, it will go back to Track #1.

Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 10
14.SEARCH BUTTONS This search button allows you to quickly scan backwards through a track. This search button allows you to quickly scan forwards through a track.
15. TRACK ButtonS This button is used to select a track. Tapping this button will forward skip to the next track, holding down this button will rapidly forward skip through the tracks. This button is used to select a track. Tapping this button will back skip on track, holding down this button will rapidly back skip through the tracks. 16. LCD DISPLAY - This high quality LCD display indicates all the various functions, as they are occurring. This display is viewable at several comfortable angles (see page 8). The display ICONS will be explained on page 16.
Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 11
17. OURCE SELECTOR SWITCH - These S switches are used to select the input source assigned to each channel. Each channel may only be assigned one input source at a time. 18. AUX INPUT - This Aux input is for the use of a Mp3 player. Input volume will be controlled by the channel two fader 19. Channel Gain Control - This adjustment is used to adjust an audio source signal input gain for a channel. Never use the gain control to adjust output volume. Setting the gain level properly will ensure a clean output signal. To properly set the gain level controls: 1. Be sure the Master Volume Con- trol (28) is set to level 4. 2. Set the Channel Fader (22) to level 8. 3. Begin playback on an audio source connected to the channel you are adjusting. 4. Use the Gain Control (19) to adjust an average output volume of +4 dB.
5. Repeat this step for all channels
20. Channel Equalizer - All of the channels include a three-band signal EQ. These controls are used to increase or decrease the LOWs, MIDs, and HIs of the output signal. CHANNEL treble control - This knob is used to adjust the treble levels of a channel allowing for a maximum treble gain of +12dB or maximum decrease of -30dB. Turning the knob in a counter-clockwise direction will decrease the amount of treble applied to a channel signal, turning the knob in a clockwise direction will increase the amount of treble applied to a channel signal. CHANNEL midrange control - This knob is used to adjust the midrange levels of a channel allowing for a maximum midrange gain of +12dB or maximum decrease of -30dB. Turning the knob in a counter-clockwise direction will decrease the amount of midrange applied to a channel signal, turning the knob in a clockwise direction will increase the amount of midrange

42.POWER CONNECTOR - This connection is used to connect your main power. Be sure that your local power matches the units required power. NEVER REMOVE THE GROUND PRONG FROM THE POWER CABLE, DOING SO MAY RESULT IN IMPROPER OPERATION.
Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 15

CD PLAYER LCD

Figure 6
53 D. LCD DISPLAY PANEL (FIGURE 6) 43. PLAY/PAUSE Indicator - Either the play or pause indicator will glow depending which mode you are in. 44.CUE Indicator - This indicator will glow when the unit is in CUE or mode and will flash every time a new CUE POINT is set. 45.Mp3 indicator - This will indicate that a Mp3 disc is loaded in the drive. 46. Elapsed Indicator - This indicator is in direct reference to the time meter (53). When the Elapsed indicator is displayed in the LCD (16), the time defined will refer to a single track's elapsed time. The time mode is changed by the tapping on the TIME BUTTON (2). 47.Single indicator - This indicates that the CD drive is in single play mode, the track will play once and return to CUE mode. If the single indicator is not on the unit is in continuous mode In continuous mode the drive will play all the remaining tracks on the disc. 48. Total Remain indicator - When "REMAIN" is indicated in the LCD DISPLAY (16) the time Display (53) in the LCD will define the current track's remaining time. When "TOTAL REMAIN" is indicated in the LCD DISPLAY (16) the time Display (53) in the LCD will define the total disc remaining time (for CD only). 49. Pitch indicator - This icon will glow when the pitch function is activated.
50. Loop - This icon will glow when you are in loop mode. 51. PITCH meter - This meter will display the pitch percentage applied by the PITCH SLIDER (4). 52.Time bar indicator - This bar gives a visual approximation of a track's or disc's remaining time. This bar will begin to flash when a CD is ending. 53. TIME DISPLAY - These indicators detail the Minutes, Seconds, and Frames. The meter will display either the elapsed or remaining time of a track. 54. Track indicator - This indicator details the current track. The number displayed in the track indicator is a direct reference to the track in play, pause, or cue mode.
Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 16
1. Loading/EJECTING discs

BASIC OPERATIONS

Figure 13

2)You may also use the Jog wheel (9) to set a cue point. While a disc is in PAUSE or CUE mode, use the Jog wheel (9) to scroll through a track and find your desired starting point. Once you have found your desired CUE point press the Play button (11) to set your cue point. Pressing the cue Button (12) will now return you to this exact point.

Figure 14

3) You may also use the SEARCH BUTTONS to set a cue point. While a disc is in PAUSE or CUE mode, use the SEARCH BUTTONS to scan through a track to find your desired starting point. Once you have found your desired position press the PLAY BUTTON to set your cue point. Pressing the CUE BUTTON will now return you to this exact point.
Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 19
9. Creating and playing a Seamless Loop
A seamless loop is a sound loop that plays continuously without sound interruption. You can use this loop to create dramatic effect in your mixing. This loop has no time limit and you could actually loop the entire length of disc. You create a seamless loop between two continuous points of a disc.
1)Press PLAY/PAUSE button (11) to activate playback mode.

Figure 15

2)Press the IN Button (10). This will set the starting point of the SEAMLESS LOOP. The IN Button (10) LED will light.

Figure 16

3)Press the OUT BUTTON (10) to set the ending point for your LOOP (Figure 17). The IN BUTTON (10) and OUT button (10) LEDs will immediately begin to flash rapidly, indicating the SEAMLESS LOOP mode has been activated.
LCD LOOP INDICATORS - During a loop, the loop indicator (50)
will turn on in the LCD DISPLAY (16) indicating a loop is active.

Figure 17

Exiting a loop - To exit a SEAMLESS LOOP, press the OUT
BUTTON (10). The IN button (10) and OUT button (10) LEDs will remain lit. Music playback will resume normal play. The IN button (10) and OUT button (10) LEDs will remain lit to remind you that a loop is in memory.

Figure 18

Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 20
Replay Loop - The RELOOP (8) function allows you to return to your stored
loop at any time. The IN button (10) and OUT button (10) LEDs will indicate a loop is stored in memory, and may be played at any time. To replay the loop, press the RELOOP BUTTON (8). The IN button (10) and OUT button (10) LEDs will again begin to flash indicating SEAMLESS LOOP mode has been activated and your loop will immediately begin to play.

must turn on the pitch adjustment function. Press the on/off button (5) located at the top right of the unit. The on/off button (5) led will glow when the function is activated. If the pitch function is not activated the pitch slider will not function.

Figure 22

Using the PITCH SLIDER (4): Be sure the pitch function has been activated as described above. To use the pitch slider slide the slider up and down. Down will increase the pitch and up will decrease the pitch.

Figure 23

Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 22
Adjusting the Pitch Slider's Range (6): You may change the
pitch slider's (5) operating range at any time. To change the operating range be sure the pitch function is turned on, see figure 33. The pitch percentage can be changed between +/-4%, +/-8%, and +/-16%. 4% will allow the least amount of pitch manipulation and 16% will allow the most amount of pitch manipulation. To adjust the different ranges, press the Pitch ON/Off Button (5) and tap on the pitch range button (6) until your desired value is reached, see figure 24.

Figure 24

2. Pitch Bending: Unlike the PITCH SLIDER (4) adjustment this function will momentarily increase or decrease a tracks speed
during playback. There are two ways to operate this function with the (-) & (+) pitch BEND buttons (7) or with the jog wheel (9). The maximum pitch bend percentage allowed is +/- 16%. The pitch bend function will work in conjunction with the PITCH SLIDER (4) pitch setting. For example, if the PITCH SLIDER (4) is set to a 2% pitch gain the pitch bending process will begin at 2% and will continue to the maximum of +/- 16%.
Holding down or tapping on the (-) PITCH BEND button (7) will provide a slow down in the playback pitch.

Figure 25

Holding down or tapping on the (+) PITCH BEND button (7) will provide a speed bump in the playback pitch.

Figure 26

Pitch bend buttons (7):
The (+) PITCH BEND button (7) will increase track playback speed and the (-) PITCH BEND button (7) will decrease track playback speed. The extent to which the speed changes is proportionate to the amount of time the button is pressed. For example, if the (+) PITCH BEND button (7) is held down continuously as in figure 26, the disc speed will increases and will continue to increase until it reaches a maximum of 16% speed gain. When you release the (+) Pitch bend button (7) the disc speed will automati ally return to its previous set speed.
Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 23

3. Jog wheel (9):

The jog wheel will temporarily bend the pitch if a track is in playback mode Rotating the wheel in a clockwise direction will increase your track pitch and rotating the wheel in a counter-clockwise direction will slow your track pitch. The speed you rotate the JOG Wheel will determine pitch bend percentage (%). For example, if the JOG Wheel is continuously turned in a counterclockwise direction the playback speed will steadily decrease and will continue to decrease until playback reaches a maximum of -100% and playback stops entirely. When you stop turning the JOG Wheel the disc speed will automatically return to its previous set speed.

Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 28
Warranty WARRANTY INFORMATION: The CK 800Mp3 carries a ONE year (365 days) limited warranty.
This warranty covers parts and labor. Please fill out the enclosed warranty card to validate your purchase and warranty. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Please contact American Audio customer support at (800) 322-6337 for a R.A. number. All package not displaying a R.A. number on the outside of the package will be returned to the shipper.

1-YEAR LIMITED WARRANTY

A. American Audio hereby warrants, to the original purchaser, American Audio products to be free of manufacturing defects in material and workmanship for a period of 1 Year (365 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owners responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought. B. For warranty service, send the product only to the American Audio factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, American Audio will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be shipped with the product. If any accessories are shipped with the product, American Audio shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof. C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which American Audio concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the American Audio factory unless prior written authorization was issued to purchaser by American Audio; if the product is damaged because not properly maintained as set forth in the instruction manual. D. This is not a service contract, and this warranty does not include maintenance, cleaning or periodic check-up. During the period specified above, American Audio will replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of American Audio under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of American Audio. All products covered by this warranty were manufactured after January 1, 1990, and bear identifying marks to that effect. E. American Audio reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by American Audio in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumers and or Dealers sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall American Audio be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product. G. This warranty is the only written warranty applicable to American Audio Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.

LINE, Aux: More than 65dB @1Khz between L and R +12 +/-2dB at 70Hz, Below -29dB at 70Hz +12 +/-2dB at 1KHz, BELOW -26dB at 1KHz +12 +/-2dB at 13KHz, -14 +/-3dB at 13KHz More than 75dB at 1KHz More than 70dB at 1KHz Channel Equalizer: BASS: Mid: Treble: Fader Maximum Attenuation: Channel Fader: Crossfader:

CD Player SECTION

AUDIO CHARACTERISTICS (TEST DISC: TCD-782, LOAD=47Kohm, Input Gain at Center) Output level 0dBV (1V) +/-2dB (TCD-782 TRK16, Max. Input Gain) T.H.D. + NOISE Less than 0.03% (TCD-782 TRK2; W/ 20KHz LPF) Frequency response 20Hz-20KHz, +/-2dB S/N ratio More than 85dB (W/ 20KHz LPF, A-Weighted) Channel separation More than 65dB @ 1KHz (W/ 20KHz LPF, A-Weighted) De-emphasis response -20dB +/-2dB (TCD-782 TRK14) SEARCHING TIME (TEST DISC: TCD-792) Short access time Less than 4sec to next track Long access time Less than 6sec from Track 1 ->Track 20 PLAYABILITY Interruption Black dot Finger prints Eccentricity Vertical deviation PICK-UP System Object lens drive system Tracking detection Optical source Wave length More More More More More than than than than than 800um (TCD-725) 600um (TCD-725) 65um (TCD-725) 140um (TCD-712) 500um (TCD-731R)
Object lens drive system optical pick-up 2 dimensional parallel drive 3 spot beam detection Semiconductor laser 780nm
NOTES: Specifications and improvements in the design of this unit and this manual are subject to
change without any prior written notice.
Audio - www.AmericanAudio.us - CK 800Mp3 Instruction Manual Page 31
American Audio World Headquarters: 4295 Charter Street Los Angeles, CA 90058 USA Tel: 323-582-3322 Fax: 323-582-3311 Web: www.AmericanAudio.us E-mail: info@americanaudio.us

Designed For The Working Professional.

CONTENTS:

DIGITAL MEDIA PLAYERS / MIDI CONTROLLERS SOUND CARDS / POCKET RECORD MEDIA PLAYBACK SOLUTIONS CD / MP3 PLAYERS PRO MIXERS PA MIXERS P. 134-139 P. 140 P. 141-143 P. 144-148 P. 149-154 P. 155-157
PRO AMPLIFIERS RACK ESSENTIALS AUDIO ESSENTIALS SOUND REINFORCEMENT CASES & ACCESSORIES
P. 158-160 P. 161 P. 162-163 P. 164-167 P. 168

www.americanaudio.eu

www.americanaudio.us

AMERICAN AUDIO

DIGITAL MEDIA PLAYERS / MIDI CONTROLLERS

RA D I US 0 0

pr ofessional single mp3 /cd player
Whether you DJ with CDs or a computer, the American Audio, Radius 1000 will help you achieve the next level! The Radius 1000 is a professional CD/MP3 player with Midi capabilities so DJs can control their favorite music playback software. It features a large 6-inch (150mm) jog wheel, 9 on-board DSP effects, and a large bright display that shows track titles and artist ID tags. Radius 1000 has a red LED visual marker display that rotates around the jog wheel to show the reference point of where the CD/MP3 disc is playing. The Radius 1000 also offers features only found on the highest quality CD Players, such as: Slot load CD Drive, Quick MP3/CD disc recognition, Advanced Track Search (search for a new track while one is playing), 10 seconds of Anti-shock memory, Seamless Loop, 3 Flash Start buttons, Digital BPM Counter, and Digital Output (S/PDIF). F E AT U R E S :. Plays MP3, CD & CD-R discs. Midi software compatible via USB (Control up to 8 MIDI channels at once). Display shows track titles and artist from ID tags when played. Advanced cueing with track searching by frame (not by each second). Quick MP3/CD recognition. Track and Folder Search. Advanced Track Search: Search for a new track while one is playing. PowerTouch advanced digital scratching (with adjustable sensitivity). 2 Scratching modes: Digital Scratch mode, Beat Juggle mode. Tempo Lock. Instant Start. 9 On-board FX: Scratch, Filter, Echo, Trans, Skid, Phase, Flanger, Pan, Bop. 6-inch (150mm) Jog Wheel with LED Cue marker and adjustable LED effects. 3 mode Jog Wheel: Normal, Scratch, and Auto Cue Scratch(Great for Beat Juggling). Time & Ratio adjustment for digital FX. FX sync adjustment. Red LED Visual marker display: Reference point to view where the disc is playing. Digital BPM Counter: keeps digital FX in sync with music.TAP Button for manual BPM. Anti Shock (10 sec.). Smart loop: Automatically measures your loop. Fader Q Start. Independently adjustable Pitch Bend (up to 100%). Sleep Mode (Adjustable in increments of 5 min - up to 120 minutes). 3 Flash Start Buttons with (5 second sample each button). Recall memory of Q-Start and samples. Store up to 1500 cue points. Digital Output (S/PDIF). Headphone jack on rear with volume control. Slot load CD drive. Flip Flop Relay playback between two Radius 1000 CD/MP3 Players. Dimensions (LxWxH): 10.5 x 14 x 4.25 / 265x356x106 mm. Weight: 8 lbs. / 3.6 kgs.

R A DIUS 3000

pr ofessional media player
Whether you DJ with CDs or a computer, the American Audio, Radius 3000 will help you achieve the next level! The Radius 3000 is a professional CD/MP3/WAV player with Midi capabilities so DJs can control their favorite music playback software. It features a large 6-inch (150mm) jog wheel, 9 on-board DSP effects, and a large bright display that shows track titles and artist ID tags. Radius 3000 has a white LED visual marker display that rotates around the jog wheel to show the reference point of where the CD/MP3/WAV disc is playing. The Radius 3000 also offers features only found on the highest quality CD Players, such as: Slot load CD Drive, Quick CD/MP3/WAV disc recognition, SD Card and USB inputs, Advanced Track Search (search for a new track while one is playing), 10 seconds of Anti-shock memory, Seamless Loop, 3 Flash Start buttons, Digital BPM Counter, and Digital Output (S/PDIF). F E AT U R E S :. Plays MP3, WAV*, CD & CD-R discs. Includes SD Card and USB inputs for additional music playback sources (such as SD, SDHC, USB Hard Drives). New & improved Database Builder for USB Drives: Sort your music by Title, Artist, Album or Genre in alphabetical order (ID3 tag info). Midi software compatible via USB (Control up to 8 MIDI channels at once). Display shows track titles and artist from ID tags when played. Advanced cueing with track searching by frame (not by each second). Quick MP3/CD recognition. Track and Folder Search. Advanced Track Search: Search for a new track while one is playing. PowerTouch advanced digital scratching (with adjustable sensitivity). 2 Scratching modes: Digital Scratch mode, Beat Juggle mode. Tempo Lock. Instant Start. 9 On-board FX: Scratch, Filter, Echo, Trans, Skid, Phase, Flanger, Pan, Bop. 6-inch (150mm) Jog Wheel with LED Cue marker and adjustable LED effects. 3 mode Jog Wheel: Normal, Scratch, and Auto Cue Scratch (Great for Beat Juggling). Time & Ratio adjustment for digital FX. FX sync adjustment. White LED Visual marker display: Reference point to view where the disc is playing. Digital BPM Counter: keeps digital FX in sync with music.TAP Button for manual BPM USB COMPACT DISC SLOT. Anti Shock (10 sec.) HARD DRIVE MP3 WAV. Smart loop: Automatically measures your loop. Fader Q Start. Independently adjustable Pitch Bend (up to 100%). Sleep Mode (Adjustable in increments of 5 min - up to 120 minutes). 3 Flash Start Buttons with (5 second sample each button). Recall memory of Q-Start and samples HEADPHONE OUTPUT. Store up to 1500 cue points. Digital Output (S/PDIF). Headphone jack on rear with volume control. Slot load CD drive. Flip Flop Relay playback between two Radius 3000 CD/MP3 Players. Built-in MIDI output and input remapping RADIUS-CASE Compatible with: Radius. Change device name (Radius 3000 A-H) for easy set-up. Link Mode: Gives the user the ability to plug in a USB Hard Drive into one Radius 3000 yet operate it from additional USB linked Radius 3000 players (up to additional 2 units). Dimensions (LxWxH): 10.5 x 14 x 4.25 / 265x356x106 mm. Weight: 8 lbs. / 3.6 kgs. *Supports most WAV files (PCM 1411 Kbps). May not be compatible with 1411.2 Kbps WAV files.

PCDJ DEX LE SOFTWARE Minimum System Requirements: WINDOWS XP or WINDOWS VISTA (32-bit and 64-bit supported) PIV 1.2 GHz computer (SSE2 CPU), AMD 64 or Greater 1024768 SVGA video DP2 Controller with built-in ASIO soundcard1 Gig RAM (XP), 2 GIG RAM (Vista) 40 MB free on the hard-drive (recommended 200MB)
D P2 F E AT U R E S :. 4 sample buttons per side (Sample length can be adjusted in preference dialog / Audio system setting page (8~30 seconds per sample if the PC hard disk memory size allow). MIDI capable. 4 Hot Cue buttons per side. Seamless Loop. Smart loop. X & Y Parameter adjustment. Scratch effect. Pitch Lock (Tempo Lock) + Pitch Bend. Pitch Adjustment Knob (+/- 4%, +/- 8%, +/- 16%). 2 channel mixer & crossfader. Back panel: USB input, headphone input, microphone input, RCA Outputs
B A S I C S YS T E M R E Q U I R E M E N T S :. Intel Pentium 4 1GHz processor, Intel Centrino Mobile Technology 1.6GHz, or above. Intel Celeron Processor NOT recommended. Microsoft Windows XP or Vista. DirectX 9 or above. Windows Media Player 9 or above. 512MB RAM. 250MB disk space (200MB for cache). Microsoft DirectSound and ASIO compatible sound card R E CO M M E N D E D S YS T E M R E Q U I R E M E N T S :. Intel Pentium 4 2.4GHz processor, Intel Centrino Mobile Technology 1.6GHz, or above. Microsoft Windows XP or Vista. DirectX 9 or above. Windows Media Player 9 or above. 1GB RAM. 550MB disk space (500MB for cache). Microsoft DirectSound and ASIO compatible sound card
D I M E N S I O N S & W E I G H T:. Dimensions (LxWxH): 19 x 5.25 x 5.25 / 482x132x133mm 3 rack spaces. Weight: 5 lbs. / 2.1 kgs.

V M S4

( Velo city M idi Sta t i o n )
pr ofessional midi sound mixing st ation
G E N E R A L F E AT U R E S : Midi Controller with 4 USB / Analog selectable MIDILOG (Midi & Analog) channels All audio control faders, knobs, switches, and buttons smoothed eliminates popping, wiper noise, and zipper noise On/off soft startup and turnoff Gain/treble/mid/bass EQ on all MIDILOGTM channels 2 phono/line selectable analog channels Two microphone channels with illuminated on/off switches and gain/treble/mid/bass EQs On/off cueing on each MIDILOGTM channel Split cueing headphones with rotary mix control Illuminated rubber knobs for ease of use in dark environments Solid 1.6mm thick faceplate for extra durability Panel mounted rotary knobs Full analog mixer operation if the computer crashes or with external power supply Innofader replaceable crossfader compatible (sold separately) Crossfader curve control Crossfader assign and reverse Q-Start crossfader controlled startup for 2 external audio players User replaceable channel faders Master and Booth outputs with L/R balance Balanced Master outputs 12 position stereo master output VU meter

M I D I F E AT U R E S :. Built-in mouse pad. Long life MIDI assignable touch strips. Two 10- bit resolution pitch sliders. 62 assignable MIDI buttons and switches. 50 MIDI buttons have LED illuminations, including 18 with dual blue/red LEDs. 4 assignable rotary encoders. 34 assignable rotary controllers. 5 assignable linear fader controllers. Dual MIDI controls on all buttons and switches. Dual 2000 point resolution touch sensitive turntable scratch controllers AU D I O F E AT U R E S : 24-bit 48 kHz analog audio 16-bit 44.1kHz USB audio 10-bit resolution on all analog fader controls THD <0.1%* Channel separation >60dB* S/N ratio >85dB* Analog channel audio latency < 1msec Selectable USB modes: 4 in 4 out mode for running software effects on phono/line analog channels or 2 in 8 out mode for running 4 software channels and master recording 2 msec response on all buttons 4 msec response on all rotary and linear faders 1 msec USB latency * For each audio channel, both line and phono modes
SOUND CARDS / POCKET RECORD

AUDIO GE NIE I I

USB audio int er face Turn you music from analog to digital with ease!
The American Audio Genie II is a great way to convert any analog signal into digital files. This easy-to-use audio interface connects directly to your PC by its USB connection. Record audio with your computers built-in audio recorder or your favorite audio production software.
AU D I O G E N I E I I M A I N F E AT U R E S :. 16-bit/44.1 kHz AD/DA converter. Line input gain knob. Line/ phono selector. 2 input - 2 output. RCA analog connections. USB bus - powered, adapter-free. Dimensions (LxWxH): 75 x 107 x 30.5 / 2.95 x 4.21x 1.2. Weight: 0.3 lbs. / 0.14 kgs Import audio using these programs (plus others) Windows: Audition Macintosh: Garage Band, Audio Hijack Pro (OSX) AU D I O G E N I E P R O M A I N F E AT U R E S : No soundcard or additional drivers needed Signal and peak LED indicators Built-in low noise phono preamp circuit Frequency Response: 10Hz-20Khz, +/-.5dB THD: 0.01% Typical @ 1KHz Hum & Noise: >89dB below clipping Maximum Input Level: 40mVrms @ 1 Khz (phono), +19dBu (line) Analog Output Connections: RCA (preamp line output), 1/8 Mini-Jack (USB monitor/headphone output) A/D & D/A: 16 bit, 44.1Khz or 48Khz USB selectable Computer Interface: USB 2.0 compliant, Windows 98, XP/ Mac OS9.1 & X 10.1 or newer Microsoft Vista Premium Level Compliant Dimensions (LxWxH): 4 x 3 x 1.5 / 113 x 73 x 40mm Weight: 0.5 lbs. / 0.22 kgs.

* Reads SD cards up to 4GB each / SD card slot does not accept SDHC cards, SDHC card can be read via USB card reader.
M E D I A O P E R AT O R F E AT U R E S :. One USB 2.0 and one SD card* slot for full functioning MP3 player. Full playback control similar to most Pro CD players. Reads SD/SDHC cards up to 32GB each. Folder & Track Search knobs. Auto BPM. Seamless Loop. Easy-to-use. Tempo Lock. Pitch Control (+/-4%, +/-8% or +/-16%). Pitch Adjust knob. Pitch Bend
. Advanced cueing with track search by frame. Bright LCD display. Master volume control. Microphone input (XLR/1/4?combo) with mic volume control. Repeat mode. Single/Continue, Time viewing and MP3 track listings. Up to 1000 MP3 songs on a 1G SD card** (MP3 recorded at 128 bit rate)**. Dimensions (LxWxH): 19 x 5.5 x 1.75 / 482 x 139 x 43 mm / 1 rack space. Weight: Main unit 1.6 Kgs, PSU 200grams
pr ofessional dual SD car d player
Going Mobile Has Never Been Easier! NOW Supports SDHC Cards!
Your whole nights music can fit on one SD Card!
M A I N A DVA N TAG E S :. No external Hard drives. No expensive laptops.No extra MP3 players. No complicated software to learn. Now supports High Capacity SD Cards (SDHC)** S DJ -1 M A I N F E AT U R E S :. Dual SD card slot for full functioning MP3 player (currently shipping models that support High Capacity SD Cards (SDHC)**. Folder Search. Auto BMP. Seamless Loop. Easy to use. Full playback control similar to most Pro CD players. Tempo Lock. Fast, Simple & Reliable. Great for Drops. Fader Q Start. Pitch Control (+/-4%, +/-8% or +/-16%). Pitch Bend. Advanced cueing with track search by frame. S/PDIF digital output for each player. Bright LCD display Single/Continue, Time viewing and MP3 track listings. Up to 1000 MP3 songs on a 1G SD card* (4GB SD card not included / MP3 recorded at 128 bit rate)*. Dimensions (LxWxH): 19 x 3.46x 4.25 / 482 x 88 x 108. Weight: 4 lbs. / 1.8 kgs

SD J -2

pr ofessional media car d player
Going Mobile Has Never Been Easier!
M A I N A DVA N TAG E S :. No external Hard drives or expensive laptops. No compicated software to learn. No MP3 players or software needed. Supports High Capacity SD Cards (SDHC) and Standard SD Cards. Built-in 2-channel mixer with High & Low adjustments, Mic Volume and Master Volume control. USB input on front for optional external media sources (ie. Additional SD Cards, hard drives and MP3 players). Balanced outputs on rear to go directly to powered speakers or amplifers S DJ -2 M A I N F E AT U R E S :. Dual SD card slots and USB Portfor full functioning MP3 player or Flash Drives. Supports High Capacity SD Cards (SDHC). Folder Search. Auto BPM. Seamless Loop. Full playback control similar to most Pro CD players. Tempo Lock. Master Volume/ Mic control. Fast, Simple & Reliable. Balanced TRSand RCAmixed output (send signal direct to amplifier or powered speakers). Independent RCA outputs for eachPlayer (send signal to pre amp mixer). Fader Q Start. Dual Mode Cross fader. Pitch Control (+/-4%, +/-8% or +/-16%). Pitch Bend. 3 Cue Buttons per Folder.Advanced cueing with track search by frame. Mic jack input on rear of player. Bright LCD display. Single/Continue, Time viewing and MP3 track listings. Dimensions (LxWxH): 19x3x 5.25 / 482 x 74.8 x 132mm 3 rack spaces. Weight: 5 lbs. / 2.2 kgs.

CD / MP3 PLAYERS

C K-M P 3
pr ofessional mp3 /cd player /mixer
M P3 / C D P L AY E R S M A I N F E AT U R E S :. Plays MP3, CD & CD-R discs. Display shows track (song) title and artist when a MP3 disc is played (ID3TAG). Advanced cueing with track searching by frame (not by each second). Advanced Track Search by track (song) title or by Folder Search. Quick MP3/CD recognition. TAP sync BPM. Tempo Lock. Instant Start. Digital Scratch FX. TAP Button for manual BPM. Anti Shock (20 sec. per side). +10 track advance button. Seamless loop. BOP effect. Q-Start. Pitch range: +/- 4%, +/- 8%, +/- 16%. Selectable elapsed, remain & total remaiming time display. Single or continuous play
M I X E R M A I N F E AT U R E S :. 2 Channel Pro mixer built-in. Inputs: 2 CD (built-in), 2 Line, 1 Aux, 1 Mic. Bass, Mid, Treble & Gain adjustment for each channel. Master Level, Mic Level, Cue Pan & Cue Level adjustment. Stream Flow LED indicators for each channel. Flip Flop On/Off button Relay playback between two CD Players. Auxiliary input on face Mini Jack great for Portable MP3 players or satellite radio receivers
R E A R PA N E L F E AT U R E S :. XLR Balanced XLR Outputs. Digital Output (S/PDIF). 2 additional line inputs. Mic input (XLR or 14 input). Multi-voltage Switch: 115V/60Hz or 230V/50Hz. Power On/Off button. Dimensions (LxWxH): 17.75 x 11.25 x 4.5 / 450x285x110mm. Weight: 13 lbs. / 6 kgs.

C K-0 M P 3

M P3 / C D P L AY E R S M A I N F E AT U R E S :. Plays MP3, CD & CD-R discs. Quick MP3/CD recognition. Instant Start. Anti Shock (20 sec. per side). +10 track advance button. Loop & Reloop. Q-Start. Pitch range: +/- 4%, +/- 8%, +/- 16%. Selectable elapsed, remain & total remaiming time display. Single or continuous play
C K- C A S E. Compatible with - CK-800 - CK-1000
R E A R PA N E L F E AT U R E S :. XLR Balanced. Digital Output (S/PDIF). 2 additional line inputs. Mic input (XLR or 14 input). Multi-voltage Switch: 115V/60Hz or 230V/50Hz. Power On/Off button. Dimensions (LxWxH): 17.75 x 11.25 x 4.5 / 450x285x110mm. Weight: 13 lbs. / 6 kgs.

CDI 300 MP3

M P3 F E AT U R E S :. Plays MP3, CD & CD-R discs. Display shows track (song) title and artist when a MP3 disc is played. Advanced cueing with track searching by frame (not by each second). Quick MP3/CD recognition. Folder Search M A I N F E AT U R E S :. Digital Scratching 2.0 (Accurate Scratching). Visual marker display: Reference point to view where the disc is playing. Anti Shock (10 sec.). Seamless loop. Fader Q Start. 3 flash start buttons with (5 second sample each button). Tempo Lock. Auto BPM Counter. Hyper Pitch (+/- 4%, +/-8%, +/-16%, +/-100%). Digital output (S/PDIF). Dimensions (LxWxH): 13.75 x 9.75 x 4.25 / 348x246x106 mm. Weight: 7 lbs. / 3.3 kgs.

*May var y depending on bit rate of your MP3 f iles.

C D I 300 MP3 SYSTEM

. 2 x CDI 300 MP3 CD Players. 1 x Q-D6 Mixer. Case & Component cables included
V E LO C I T Y M P3 F E AT U R E S :. Plays MP3, CD & CD-R discs. Quick MP3/CD recognition. Display show track listing and artist when a MP3 disc is played. Advanced cueing with track searching by frame (not by each second). Advanced Track Search by track (song) title or by Folder Search. Fine Tune B.P.M. adjustment. Cue Point. Advance Track Launch V E LO C I T Y M P3 F E AT U R E S :. PowerTouch** , Touch sensitive interactive jog wheels (**U.S. & foreign patents pending). Digital Scratching 2.0 (Accurate Scratching). 2 Scratching modes: Digital Scratch mode, Beat Juggle mode. 9 On-board FX: Scratch, Filter, Echo, Trans, Skid, Phase, Flanger, Pan, Bop. Effect layering. Digital B.P.M. counter: keeps digital FX in sync with music. 6 Preset Parameters settings for each FX. Tempo Lock (Master Tempo). Parameter Ratio & Time adjustment knobs. Hyper Pitch (+/-4% up to +/-100%). 3 Flash Start Sampler Buttons per side (7 second sample per button with or without a CD in drive). Slot Load Dual CD Player. Digital Anti-shock memory. Instant start. Seamless loop. Fader Q Start. Reverse play. Digital output - S/PDIF. Volume control between music and sampler. FX MIX. Store 384 cue points or samples. Flip Flop (Relay playback between two decks). Dimensions MAIN UNIT: 19 x 10 x 3.5 (2 rack spaces) CONTROL UNIT: 19 x 2 x 7 (4 rack spaces). Weight (total): 16 lbs.

V EL O C I TY

pr ofessional dual mp3 /cd player

PL AY U P TO

O F M P3 M U S I C P E R D I S C *

MC D-7 10

M A I N F E AT U R E S :. Plays MP3, CD & CD-R discs. Fader Q Start. +10 track advance button. -10 back track button. MP3 Folder Search. Auto BPM. Tempo Lock. 20 seconds Anti Shock Protection (per side). Flip Flop (Relay Playback). Pitch Control (+/-4%, +/-8% or +/-16%). Pitch Bend. Advanced cueing with track search by frame. S/PDIF digital output for each player. Bright LCD display Single/Continue and Time viewing. Reads CD and CD-R media. Update firmware via CD-ROM. Dimensions (LxWxH): Player unit: 10 x 19 x 3.5 Controller: 2.5 x 19 x 3.5 (2-spaces). Weight:15 lbs.

DCD - P R O 310 M KI I

pr ofessional dual cd player
M A I N F E AT U R E S. Audio CD & CD-R compatible. Single/Continuous playback. +10 track advance button. Single Repeat mode. Mechanical Anti-Skip Protection. Flip Flop (Relay Playback). Pitch / Frame search jog modes. Pitch Control (+/-4%, +/-8% or +/-16%)
. Pitch Bend. Bright LCD display: Single/Continue and (3) Time viewingmodes. Dimensions (LxWxH):. Player unit: 10 x 19 x 3.5 / 254x482x89mm(2 rack spaces). Controller: 2.5 x 19 x 3.5 / 64x482x89mm (2 rack spaces). Weight:15 lbs./ 7kgs.

MC D- 1 10

pr ofessional mp3 /cd player

Q -D1 PR O

pr ofessional mixer
Q - D1 PR O M A I N FE AT U R E S. 2 band EQ w/input gain control per channel. High level master output, high current phones output. Power on/off muting. Low sound leakage cross fader. Low distortion (0.0028%), low noise (S/N=112dB). CD play control by cross fader. Record out. USB Device Port (USB device not included) with Play/ Pause Next andPrevious Buttons. Balanced TRS Outputs. Power Source: AC 9V, 1000mA. Dimensions (WxDxH): 8.62 x 10.04 x 3.94 / 219x255x100mm. Weight: 5 lbs. / 2.3 kgs.

Q -D 1 M KI I

Q - D1 M A I N FE AT U R E S. 2 Phono, 2 Line, 1 Mic inputs. Q-Start. Gain, treble and bass control for each channel. Master, Microphone and Cue Level volume control. Cue monitoring between channels. 1/4 jacks for Mic & Phono input. 9V AC power supply included. Dimensions (LxWxH): 9.5 x 7.5 x 4. Weight: 4 lbs.

Q -D 6

pr ofessional 10-inch mixer
Q-D6 M A I N F E AT U R E S. 3-channel Pro DJ Mixer. 2 Phono, 3 Lines, 2 Aux & 1 Mic input. Mini plug input on face of mixer for use with MP3 players & satellite receivers. Balanced Outputs. Fader Q Start Compatible. Gain, Treble, Mid & Bass control for each Ch. (-26 dB Rotary Kills). DJ Mic with Volume, Treble, Bass and Talkover control. Stream flow LED Master Level meters. Cue Mixing, Cue Level and Master Level Control. Extremely clean signal to noise ratio. Dimensions (LxWxH): 12.25 x 10x 3.25. Weight: 7 lbs.

Q-D5 M K II

Q -D5 MKII M A I N F E AT U R E S. 2 Phono, 2 Lines, 2 Aux & 1 Mic input. Optical Crossfader (tested over 1 million times)*. Balanced XLR outputs. Q-Start. Cross Fader curve knob (short to long crossfade) with reverse crossfade button. Independent curve for channels 1 & 2 (short to long curve) with reverse button. Gain, Treble, Mid & Bass control for each channel. -30 dB Rotary Kills for Treble, Mid & Bass. 100% cut buttons for Treble, Mid & Bass. Dimensions (LxWxH): x 12.25 x 10 x 3.25. Weight: 7 lbs.
*The optical fader was factor y tested over 1 m i l l i o n t i m e s b a c k- a n d - f o r t h a n d n e v e r quit working !

M X -DS P

pr ofessional 14-inch mixer
M X-0 D S P M A I N F E AT U R E S. 4-channel, 14-inch professional mixer. 3 Phono, 4 Lines, 4 Aux, 3 Mics. FX with Digital Signal Processing (DSP): Echo, Auto Pan, Flanger, Manual Filter, Auto Filter, Reverb, Trans & Pitch Shifter. Assign FX to any Mic or channel input. Parameter Time & Depth adjustment. Master & Cue BPM analyzer. Master & Mic trim output adjustment on rear. Balanced XLR outputs. Booth output (XLR). Crossfader assign on each channel. Crossfader curve. Auxiliary RCA input on face of mixer. Stream Flow LED meters. Quality mic circuitry + long lasting faders. Q-Start. Recessed back panel. Digital output (S/PDIF). Multi-voltage switch. Dimensions (LxWxH): 14 x 12.5 x 3.25. Weight: 15 lbs.

MX -14 00

M X-0 M A I N F E AT U R E S. 4-channel, 14-inch professional mixer. 3 Phono, 4 Lines, 4 Aux, 3 Mics. Master & Mic trim output adjustment on rear. Balanced XLR outputs. Booth output (XLR). Crossfader assign on each channel. Crossfader curve. Auxiliary RCA input on face of mixer. Stream Flow LED indicators. Superior mic circuitry + long lasting faders. Q-Start. Recessed back panel. Digital output (S/PDIF). Multi-voltage switch. Dimensions (LxWxH): 14 x 12.5 x 3.25. Weight: 14 lbs.

PA MIXERS

M 2 F X F E AT U R E S : Controls:. 2 Mono & 3 Stereo channels input & stereo main output. Trim with Peak LED, HPF, 3-band EQ, 1 AUX, 1 EFX & PAN for mono input. Trim with Peak LED, HPF (CH3-CH6), 3-band EQ. 1 AUX, 1EFX & balance for stereo input. Main L/R, HP/Control Room, AUX Return, Tape Level & Phantom Power. 24 bit DSP effect 100 presets, EFX ON/OFF & EFX level Input Connectors:. 4 XLR MIC/INPUTS. XLR & 1/4 phone jack balanced & 1/4 phone jack for insert on mono input. XLR & 1/4 phone jack for stereo (CH3-CH6), 1/4 phone & phono jack for stereo input (CH7-CH8). 1/4 phone jack for stereo return & phono jack for Tape Output Connectors:. 1/4 phone jack balanced for main, 1/4 phone jack for AUX, Control Room & Headphone. phono jack for Tape, 1/4 phone jack for Footswitch Indicator:. Peak for each input, level meter & phantom power Specifications M822FX:. Weight (Net): 2.8 kg. Dimensions: (W x H x D) 247 x 65 x 290 mm

M822FX

M-Series PA Mixer

PA PACK 1X

M822F X PA Mixer Package
I N C LU D E S : 1- M 2 F X 2 -X S P 10A ( s t a n d s n o t i n c l u d e d ) XSP 10A Main Features :. 10-inch 2-way Powered Speaker. Dual Amplifiers *LF/HF 200 Watt Total. 1-inch Compression Driver. Time Aligned Electronic Crossover. Flyable or Stand Mountable. Full grille. Built-in mixer with 1 Line input; 1 Mic input; Treble & Bass Control; Channel and Master Volume. XLR through output. Dimensions (LxWxH): 14 x 11 x 19 / 355x280x480mm. Weight: 31 lbs. / 14 kg. Speaker Specifications :. Frequency Response: 20Hz - 20KHz. Crossover: 3.5k. Nominal Dispersion: 90 x 50 (HXV) Amplifier Specifications :. Line: -20dB(100mV). Microphone: -40dB(10mV) *Low Frequency / High Frequency
M4 F X F E AT U R E S : Controls. 4 mono & 4 stereo channels input. Stereo Main output & ALT 3/4 output. Trim with Peak LED, HPF, 3-band EQ, 1 AUX with Pre/Post switch, 1 EFX, PAN, Mute & PFL switch for mono input. Trim with Peak LED, HPF (CH5-8). 3-band EQ, 1 AUX with Pre/Post switch, 1 EFX, BAL, Mute & PFL for stereo input. Main L/R with AFL switch, ALT3/4 with AFL, To Main switch, AUX Send, EFX send, AUX return & EFX return. Tape with PFL switch, HP/Control Room & Phantom Power. 24-bit DSP effect 100 presets, EFX on/off & EFX level Input Connectors:. 6 XLR MIC/INPUTS. XLR & 1/4 phone jack balanced & 1/4 phone jack for Insert on mono input. XLR & 1/4 phone jack for stereo (CH5-8) 1/4 phone & phono jack for stereo input. 1/4 phone jack for stereo return & phono jack for Tape Output Connectors:. 1/4phone jack for Main, ALT 3/4, AUX Send, EFX Send, Control Room & Headphone. Phono jack for Tape & 1/4 phone jack for Footswitch Indicator:. Peak for each mono channel, PFL, level meter, phantom power & DSP program Specifications M1224FX. Weight (Net): 3.4 kg. Dimensions: (W x H x D) 328 x 420 x 65 mm

M1224FX

PA PA CK 2X
M1224F X PA Mixer Package
I N C LU D E S : 1- M4 F X 2 -X S P 12 A 2 -S P S -1B XSP 12A Main Features :. High-powered 12-inch, 2-way Powered Speaker. Dual Amplifiers *LF/HF 300 Watt Total. Neodymium components. 1.75 compression driver. Time Aligned Electronic Crossover. Flyable or Stand Mountable. Full grille. Built-in mixer with 1 Line input; 1 Mic input; Treble & Bass Control; Channel and Master Volume. XLR through output. Dimensions (LxWxH): 16 x 12 x 23 / 405x305x585mm. Weight: 44 lbs. / 20 kg. Speaker Specifications :. Frequency Response: 20Hz - 20KHz. Crossover: 3.8k. Nominal Dispersion: 90 x 50 (HXV) Amplifier Specifications :. Line: -20dB(100mV). Microphone: -40dB(10mV) * Low Frequency / High Frequency

M16 24FX

M4 F X F E AT U R E S : Controls. 8 mono & 4 stereo channels input. Stereo Main output & ALT 3/4 output. Trim with Peak LED, HPF, 3-band EQ, 1 AUX with Pre/Post switch, 1 EFX, PAN, Mute & PFL switch for mono input. Trim with Peak LED, HPF (CH9-12). 3-band EQ, 1 AUX with Pre/Post switch, 1 EFX, BAL, Mute & PFL for stereo input. Main L/R with AFL switch, ALT3/4 with AFL, To Main switch, AUX Send, EFX send, AUX return & EFX return. Tape with PFL switch, HP/Control Room & Phantom Power. 24-bit DSP effect 100 presets, EFX on/off & EFX level Input Connectors:. 10 XLR MIC/INPUTS. XLR & 1/4 phone jack balanced & 1/4 phone jack for Insert on mono input. XLR & 1/4 phone jack for stereo (CH9-12) 1/4 phone & phono jack for stereo input. 1/4 phone jack for stereo return & phono jack for Tape Output Connectors:. 1/4phone jack for Main, ALT 3/4, AUX Send, EFX Send, Control Room & Headphone. Phono jack for Tape & 1/4 phone jack for Footswitch Indicator:. Peak for each mono channel, PFL, level meter, phantom power & DSP program Accessories:. 19 standard rack mountable (optional) Specifications M1624FX. Weight (Net): 5.6 kg. Dimensions: (W x H x D) 436 x 420 x 65 mm

PA PACK 3 X

M1624F X PA Mixer Package
I N C LU D E S : 1- M4 F X 2 -S P S -1B 2 -X S P 10A 2 -X S P 15A 2 - PX W 18 P PXW 18P Main Features :. 18 powered Sub. 800 watts max power. Dimensions: (LxWxH): 27 x 27 x 32 / 686 x 686 x 813 mm. Weight: 171 lbs. / 78 kgs. XSP 10A Main Features :. 10-inch 2-way Powered Speaker. Dual Amplifiers *LF/HF 200 Watt Total. 1-inch Compression Driver. Dimensions (LxWxH): 14 x 11 x 19 / 355x280x480mm. Weight: 31 lbs. / 14 kg. XSP 15A Main Features :. High-powered 15-inch, 2-way Powered Speaker. Dual Amplifiers *LF/HF 400 Watt Total. Built-in mixer with 1 Line input; 2 Mic inputs; Treble & Bass Control; Channel and Master Volume. Dimensions (LxWxH): 17 x 15 x 27 / 430x380x685mm. Weight: 57 lbs. / 26 kg. * Low Frequency / High Frequency

PRO AMPLIFIERS

VX SERIES Controls At Your Fingertips: Input Sensitivity Filters Output Configuration

VX-1000

VX-1500
550W RMS per channel 500W RMS per channel 330W RMS per channel 1100W RMS per channel 1000W RMS per channel
750W RMS per channel 700W RMS per channel 450W RMS per channel 1500W RMS per channel 1400W RMS per channel
Total Harmonic Distortion (THD): Less than 0.5% (20Hz-20kHz, @ 8 Ohms) Input Sensitivity & Impedance: 1.0v rms (0 dBv) (@ 4 Ohms) Dimensions & Weight: Height: 3.5 (88mm) Width: 19 (483mm) Depth: 16.5 (429mm) Weight: 40 lbs. (18.5 kg)
Total Harmonic Distortion (THD): Less than 0.5% (20Hz-20kHz, @ 8 Ohms) Input Sensitivity & Impedance: 1.0v rms (0 dBv) (@ 4 Ohms) Dimensions & Weight: Height: 3.5 (88mm) Width: 19 (483mm) Depth: 16.5 (429mm) Weight: 45 lbs. (18.5 kg)
Total Harmonic Distortion (THD): Less than 0.5% (20Hz-20kHz, @ 8 Ohms) Input Sensitivity & Impedance: 1.0v rms (0 dBv) (@ 4 Ohms) Dimensions & Weight: Height: 3.5 (88mm) Width: 19 (483mm) Depth: 19.5 (495mm) Weight: 52 lbs. (23.5 kg)
Frequency Response: 3dB, 1W RMS 8 ohms (20Hz - 20kHz)
Signal to Noise Ratio: Less than 95 dB , unweighted (@ 8 ohms full power) Slew Rate: 15v/usec
Signal to Noise Ratio: Less than 95 dB , unweighted (@ 8 ohms full power) Slew Rate: 15v/usec Damping Factor: 300 (@ 8 Ohms)
Signal to Noise Ratio: Less than 95 dB , unweighted (@ 8 ohms full power) Slew Rate: 15v/usec Damping Factor: 500 (@ 8 Ohms)
Damping Factor: 300 (@ 8 Ohms)
Protection Circuit: DC output protection, Overload protection, High Temp protection, Short circuit protection, Current Inrush protection, Soft start-up protection Power Consumption: 5A @ 120V AC (@ 8 Ohms) Fan: 2-speed fan
Modes: Stereo, Parallel or Bridge Mono

VX-2500

Output Power: 2 ohms, 1 khz 1% THD 4 ohms, 1 khz 1% THD 8 ohms, 1 khz 1% THD (Bridged Mode, mono) 4 ohms, 1 khz 1% THD 8 ohms, 1 khz 1% THD
1400W RMS per channel 1200W RMS per channel 750W RMS per channel 2800W RMS per channel 2400W RMS per channel
QUALITY, AFFORDABLE & RELIABLE POWER AMPLIFIERS FOR THE WORKING PROFESSIONAL.

VLP300

Output Power 4 ohms, 1 khz 0.1% THD 8 ohms, 1 khz 0.1% THD (Bridged Mode, mono) 8 ohms, 1 khz 0.1% THD 150W RMS per channel 100W RMS per channel

VLP600

300W RMS per channel 200W RMS per channel 600W RMS per channel

VLP1500

750W RMS per channel 500W RMS per channel 1500W RMS per channel

300W RMS per channel

Total Harmonic Distortion (THD) 20Hz-20kHz, @ rated output Less than 0.1% power, 8 ohms Impedance Balanced / Unbalanced Dimensions & Weight Height Width Depth Weight Frequency Response 1dB, 1W RMS 8 ohms

Less than 0.1%

20K Ohms / 10K Ohms

20K Ohms / 10KOhms

1.75 (44cm) 19 (48.3cm) 13.25 (33.6cm) 24 lbs (11 kg)
3.5 (88cm) 19 (48.3cm) 14 (36cm) 33 lbs. (15kg)
3.5 (88cm) 19 (48.3cm) 14 (36cm) 42 lbs. (19kg)

20Hz - 20 kHz

Slew Rate 15v/usec Damping Factor @ Cooling System 2 individual fans Special Features High/Low Pass Filter Input Sensitivity Selector Ground Lift
15v/usec individual fans High/Low Pass Filter Input Sensitivity Selector Ground Lift Limiter
NOTE - 1 Rackspace = Approx. 1.75

V3001plus

Output Power 2 ohms, 1 khz 1% THD 1020W RMS per channel 4 ohms, 1 khz 1% THD 670W RMS per channel 8 ohms, 1 khz 1% THD 410W RMS per channel (Bridged Mode, mono) 4 ohms, 1 khz 1% THD 2050W RMS per channel 8 ohms, 1 khz 1% THD 1360W RMS per channel Total Harmonic Distortion (THD) 20Hz-20kHz, @ rated output Less than 0.1% power, 8 ohms Input Sensitivity & Impedance @ rated output power, 4 ohms 1.0v rms (0 dBv) Dimensions & Weight Height 3.5 (88cm) Width 19 (48.3cm) Depth 15.9 (40.5cm) Weight 31 lbs. (14kg) Frequency Response 10Hz - 40 kHz.5dB, 1W RMS 8 ohms 3dB, 1W RMS 8 ohms 20Hz - 20 kHz Hum & Noise 100 dB, unweighted Below rated output, 8 ohms Signal to Noise Ratio @ 4 ohms full power unweighted, 60 dB A weighted Slew Rate 25v/usec Damping Factor @ Protection Circuit DC output protection Overload protection Short circuit protection On & Off protection Special Features Sub-Woofer Crossover Contractor Smart Feature** Limiter Power Consumption @ rated output power, 8 ohms 10A @ 120V AC Turn-On Thump Protection Yes Cooling System Dual 2 speed fans & heatsink

V4001plus

1530W RMS per channel 1090W RMS per channel 660W RMS per channel 3000W RMS per channel 2170W RMS per channel

V5001plus

2150W RMS per channel 1500W RMS per channel 980W RMS per channel 4250W RMS per channel 3100W RMS per channel Less than 0.03% @ 4 Ohms

V6001plus

2530W RMS per channel 1920W RMS per channel 1260W RMS per channel 5100W RMS per channel 3650W RMS per channel
**Contractor Smart = Switch on rear panel to disable front volume controls (Models V3001 thru V6001 only) NOTE - 1 Rackspace = Approx. 1.75
3001plus 4001plus 5001plus 6001plus
Less than 0.1% @ 4 Ohms Less than 0.03% @ 4 Ohms 1.0v rms (0 dBv) 1.0v rms (0 dBv) 1.0v rms (0 dBv) 5.25 (13.3cm) 19 (48.3cm) 15.9 (40.5cm) 62 lbs. (28kg) 10Hz - 35 kHz 5Hz - 85 kHz 3.5 (88cm) 19 (48.3cm) 15.9 (40.5cm) 31 lbs. (14kg) 10Hz - 40 kHz 20Hz - 20 kHz 100 dB, unweighted 5.25 (13.3cm) 19 (48.3cm) 15.9 (40.5cm) 62 lbs. (28kg) 10Hz - 35 kHz 5Hz - 85 kHz 100 dB, unweighted 100 dB, unweighted >100dB >100dB 25v/usec 400 >100dB 25v/usec 400 25v/usec 500 DC output protection DC output protection Overload protection Overload protection Short circuit protection Short circuit protection On & Off protection On & Off protection Sub-Woofer Sub-Woofer Crossover Speakon plugs Contractor Smart Feature** LED mode indicator Limiter Crossover 20-200Hz Contractor Smart Feature** 10A / TBA (8 ohms) 45A / 22.5A (4 Ohms) DC output protection Overload protection Short circuit protection 53A / 25.5A (4 Ohms) Yes Yes Yes 2 dual speed fan & heatsink 2 dual speed fan & heatsink 2 dual speed fan & heatsink

Sub-Woofer Speakon plugs LED mode indicator Crossover 20-200Hz Contractor Smart Feature**

RACK ESSENTIALS

RAC K COLOR LE D

L ED power panel

R AC K CO LO R L E D M A I N F E AT U R E S Easy-to-use 19-inch LED Bar used to light up your DJ rack (24 LEDs) LED Advantages: No heat output, low power draw, long life LED operation 3-pin XLR in/out Master/ Slave operation RC-1 infrared remote control included Control: color change, brightness & rainbow effect with pattern, speed and fade control LED Colors: Red, Cyan, Green, Magenta, Blue, Yellow, White & Amber Power Supply: DC 12V, 500 mA min (included) Dimensions (LxWxH): 3 x 19 x 2/ 76x483x50mm 1 rack space Weight: 1.5 lbs./0.8 kg.

P DP-85 0

power distribution panel

LED Technology

P D P- 0 M A I N F E AT U R E S. 7 protected switched A/C grounded outlets on rear of unit & 1 A/C unswitched outlet on rear of unit. Dual L.E.D. pop-out lights with dim control knob. 1 A/C outlet switched on front of panel. 15A per outlet/20A protection breaker switch on front panel. Protection: 20A breaker. USB receptacle on front panel. Great for lighting up racks. Dimensions: 19 x 1.75 x 6.5 (1 rack space). Weight: 7 lbs.

P DP-95 0

P D P- 0 M A I N F E AT U R E S. 7 protected switched A/C grounded outlets on rear of unit & 1 A/C unswitched outlet on rear of unit. 1 A/C outlet switched on front of panel. Incoming Line Voltage Meter. 15A per outlet/20A protection breaker switch on front panel. Dual L.E.D. pop-out lights with dim control knob. USB receptacle on front panel. Great for lighting up racks. Protection: 20A breaker. RFI and surge protection. Dimensions: 19 x 1.75 x 6.5 (1 rack space). Weight: 7 lbs.

d B-DIS PLAY

decibel indicat or
d B - D I S P L AY M A I N F E AT U R E S. Designed to set in an amp rack to view your decibel level. Creates a great light show in your amp rack. Display progresses from green through amber to red. Sensitivity adjustment on both left and right channels. 2 separate modes: dot and bar. Includes a 12V power supply. Power Supply: 12V DC. Line Inputs: Left & Right RCA. Line Outputs: Left & Right RCA. 1 rack mount space. Weight: 3 lbs.

P C -100/ A

power indicat or
P C-/ A M A I N F E AT U R E S. Larger easy to access buttons. A/C power center designed to eliminate extension cords and messy wires. 8 lighted switches on front panel. 15A resetable circuit breaker on front panel. Eight grounded AC sockets on rear of the unit. Ideal for switching lights and sound equipment. Maximum load: 15 amps or 1800 watts. 1 rack mount space. Weight: 4 lbs.

D L S-1 5

dj speaker
D L S -15 S P E C I F I C AT I O N S. High Powered 15-inch, 2-way speaker. Die cast woofer with 3-inch voice coil. High compression 1.75 driver. ABS nylon fiber cabinet with handle. Speakon line input. Trapezoidal design. Flyable & stand mountable. Floor monitor brackets included. Sensitivity: 109 dB/m/w. Dimensions (LxWxH): 13.6 x 16.5 x 26.4. Weight: 55 lbs.

APX -B

speaker carr y bag
A PX- B F E AT U R E S. Rugged speaker bag with rollers, adjustable handle & heavy duty zipper. Move speakers with ease. Fits: DLS-15, DLS-15P, APX-152, APX-Power Pro, PXI Series & various other brand speakers

Z-APX/H

. Heavy duty eye-hook for suspending speakers

Z-APX/B

. Heavy duty bolt for securing speakers
XSPSERIES POWERED SPEAKERS

Designed

LIVE SOUND

XSP-8A

XSP-8A: Main Features :. 8-inch, 2-way Powered Speaker. Dual Amplifiers *LF/HF 100 Watt Total. Time Aligned Crossover. ABS nylon fiber cabinet with handle. Flyable or Stand Mountable. Full grille. XLR Mic/Line input with Volume Control. Dimensions (LxWxH): 11.5 x 9 x 16.5 / 290x230x420mm. Weight: 18 lbs. / 9 kg. Speaker Specifications :. Frequency Response: 20Hz - 20KHz. Crossover: 3.3k. Nominal Dispersion: 90 x 50 (HXV) Amplifier Specifications :. Line: -20dB(100mV). Microphone: -40dB(10mV) *Low Frequency / High Frequency

XSP-10A

XSP-10A: Main Features :. 10-inch 2-way Powered Speaker. Dual Amplifiers *LF/HF 200 Watt Total. 1-inch Compression Driver. Time Aligned Electronic Crossover. Flyable or Stand Mountable. Full grille. Built-in mixer with 1 Line input; 1 Mic input; Treble & Bass Control; Channel and Master Volume. XLR through output. Dimensions (LxWxH): 14 x 11 x 19 / 355x280x480mm. Weight: 31 lbs. / 14 kg. Speaker Specifications :. Frequency Response: 20Hz - 20KHz. Crossover: 3.5k. Nominal Dispersion: 90 x 50 (HXV) Amplifier Specifications :. Line: -20dB(100mV). Microphone: -40dB(10mV) *Low Frequency / High Frequency

XSP-12A

XSP-12A: Main Features :. High-powered 12-inch, 2-way Powered Speaker. Dual Amplifiers *LF/HF 300 Watt Total. Neodymium components. 1.75 compression driver. Time Aligned Electronic Crossover. Flyable or Stand Mountable. Full grille. Built-in mixer with 1 Line input; 1 Mic input; Treble & Bass Control; Channel and Master Volume. XLR through output. Dimensions (LxWxH): 16 x 12 x 23 / 405x305x585mm. Weight: 44 lbs. / 20 kg. Speaker Specifications :. Frequency Response: 20Hz - 20KHz. Crossover: 3.8k. Nominal Dispersion: 90 x 50 (HXV) Amplifier Specifications :. Line: -20dB(100mV). Microphone: -40dB(10mV) * Low Frequency / High Frequency