American Audio

User Instructions
American Audio 4295 Charter Strret Los Angeles Ca. 90058

Revised 5/01

CAUTION Do not open risk of electric shock
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICE TO YOUR AUTHORIZED AMERICAN AUDIO DEALER.
The lightning flash with an arrow triangular symbol is intended to alert the user to the presence of non insulated dangerous voltage within the products enclosure, and may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point triangular symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the user manual accompanying the CD player.
FOR OPTIMUM PERFORMANCE AND RELIABILITY DO NOT PRESENT THE AMPLIFIER WITH A SPEAKER LOAD OF LESS THAN 2 OHMS. OR ANY COMBINATION OF SPEAKERS THAT TOGETHER ARE LESS THAN 2 OHMS!
POUR ASSURER LA FIABILETE ET OBTENIT UNE PERFORMANCE OPTIMALE, NESOUMETTE JAMAIS LAMPLIFICATEUR A UNE CHARGE DIMPEDANCE TOTALE INFERIEURE A 2 OHMS, NI AVEC UN H.P. NI EN COMBINAISON DES H.P.
USING ONE SPEAKER, IT MUST BE AVEC UN H.P., IL FAUT UNE CHARGE DIMPEDANCE MINIMUM DE 2 OHMS. RATED AT 4 OR MORE OHMS. USING TWO SPEAKERS, THEY MUST AVEC DEUX H.P., FAUT POUR CHAOUN RATED EACH AT 4 OR MORE OHMS. UNE CHARGE DIMPEDANCE MINIMUM DE 4 OHMS. USING THREE SPEAKERS, THEY MUST BE RATED EACH AT 8 OR AVEC TROIS H.P., FAUT POUR CHAOUN UNE CHURGE DIMPEDANCE MINIMUM MORE OHMS. DE 8 OHMS.
FRONT PANEL.....4 REAR PANEL.....5 OPERATING VOLTAGE.....4 INPUTS.....6 OUTPUTS......7 LIMITER......10 LOW-CUT FILTER.....11 FUSE......5 LED INDICATORS.....4 STEREO/BRIDGED MONO.....10 PROTECTION.....10
V1500 Power Amplifier Instructions page 2

Important Precautions

1. Be sure to save the packing carton in case you may ever have to return the unit for service. 2. Read all documentation before attempting to operate your new amplifier. Please save all you documentation for future reference. 3. Do not spill water or other liquids in to or on to your amplifier. 4. Be sure that the local power outlet match that or the required voltage for your amplifier. 5. Do not attempt to operate this unit if the power cord has been frayed or broken. Please route your power cord out of the way of foot traffic. 6. Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short. 7. Always have the front gain controls set to their lowest level during initial power-up to prevent speaker damage. 8. Disconnect from main power before making any type of connection. 9. Do not block the units cooling vents or fan intake. If this unit is being used in an extremely dusty or smoky environment, the unit should be blown through on a regular basis. 10.Do not remove the top cover under any conditions. There are no user serviceable parts inside. 11. Do not drive the inputs with a signal level greater than that required to drive equipment to full output. 12. Do not try to run the input signal of an amplifier by the output of any other amplifier. 13. Never ground a RED (positive) terminal. Never connect a RED (hot) terminal to another RED (hot) terminal. 14. Disconnect the units main power when left unused for long periods of time.

Introduction

Introduction: Congratulations and thank you for purchasing the
American Audio V1500 amplifier. This amplifier is a representation of American Audios continuing commitment to produce the best and highest quality products all at an affordable price. This amplifier is an ultra-compact amplifier that packs a big punch! Please read and understand this manual completely before attempting to operate your new amplifier. This booklet contains important information concerning the proper any safe operation of your new amplifier.
Unpacking: Carefully open and unpack your amplifier. Be sure
to save the packaging in case you may ever need to return your unit to the factory. After unpacking, inspect the amplifier for any type of damage that may have occurred during shipping or transit. If you notice any type of damage notify your dealer immediately for instructions.
Installation: This amplifier is made to mount in a standard 19
rack The front panel provides four holes used to screw the unit into a rack The unit also provides a way to rear mount the unit into a rack for added security. Rear mounting the unit is especially recommended if the unit is to mounted in to a mobile rack.
Customer Support: American Audio provides a toll free cus-
tomer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at www.americandj.com for any comments or suggestions. For service related issue please contact American Audio. Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time. Voice: (800) 322-6337 Fax: (323) 582-2610 E-mail: support@americandj.com

V1500 Power Amplifier Instructions page 3

FRONT PANEL

Diagram 1
11 1. Channel 1 Signal indicator -
10 6. Channel 2 Protect indicator -
This Green LED will glow when there is an input signal present. 2. Channel 1 Protect indicator This red LED will glow when channel one goes in to protect mode. In protect mode the output signal to the speakers will terminated to channel one. 3. Channel 1 Clip indicator This LED comes on at the amplifiers clipping point, the point when the output signal begins to distort. Under heavy clipping lower the input gains (Diagram 8) to reduce the risk of damage to your speakers and amplifier. 4. Power LED This LED will glow when the amplifier is turned on, indicating power is going to the unit. 5. Channel 2 Clip indicator This LED comes on at the amplifiers clipping point, the point when the output signal begins to distort. Under heavy clipping lower the input gains (Diagram 10) to reduce the risk of damage to your speakers and amplifier.
This red LED will glow when channel two goes in to protect mode. In protect mode the output signal to the speakers will terminated to channel two. 7. Channel 2 Signal indicator This Green LED will glow when there is an input signal present. 8. Channel 1 Gain control This knob adjust the channel one volume output to the speakers connect to channel one. 9. Power Switch This switch turns the unit on. 10. Channel 2 Gain control This knob adjust the channel one volume output to the speakers connect to channel one. 11. Exhaust Cooling Vents A cooling fan is mounted at rear of the amplifier. These exhaust vents allow hot air to be pushed out of the amplified to allow ample cooling of the internal components. Do Not Block These Vents!
V1500 Power Amplifier Instructions page 4

REAR PANEL

Diagram 2
1. Channel 1 Input Connect the input source for channel one to either the balance XLR or the unbalanced 1/4 input jacks. 1/4 TS plug - Tip is positive, Sleeve is negative. XLR - Pin three positive, Pin two is negative, Pin one is ground. See the chart on page 6. 2. Channel 2 Input Connect the input source for channel two to either the balance XLR or the unbalanced 1/4 input jacks. 1/4 TS plug - Tip is positive/Sleeve is negative. XLR - Pin three positive, pin two negative, pin one ground. See the chart on page 6. 3. Cooling Fan This is a dual speed cooling fan. This fan is used to cool the internal parts of the amplifier when in use. Never block the fan in any way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail. 4. A/C Power Input Plug this cable in to a standard 110~120v wall outlet. Be sure that supplied voltage matches that of the required voltage of you amplifier. Never plug your amplifier in to a wall outlet that does not match the required voltage of your amplifier, serious damage

may occur to your unit. 5. Channel 1 Speaker Output - 5 Way Binding Post Connect your channel one speakers to channel one output. 6. Channel 2 Speaker Output - 5 Way Binding Post Connect your channel two speakers to channel two output. 7. Mono-Bridge/Stereo Selectable Switch This push button switch changes the amplifier operating mode from either stereo or mono bridge. Amplifiers arrive to you preset in the stereo operation mode. 8. Fuse This house the external 8amp fuse. All way replace with exact same type fuse unless otherwise instructed to do so by an authorized American DJ service technician. 9. Ground Lift Switch This switch is used to disconnect the internal ground signal from the chassis ground. This may reduce the buzz that is caused from an electrical 60Hz cycle.
V1500 Power Amplifier Instructions page 5

INPUTS

The V1500 allows you two types of input connector per a channel, a XLR jack for balanced connections and a 1/4 jack for unbalanced connections. Use these connection to connect the output signal from a mixer, cross-over or EQ to your V1500 amplifier. The XLR connection is recommended for cable runs longer that 20ft. When building your own XLR cables follow the pin configuration describe below for proper connections. For cable runs shorter than 20Ft. you may choose the 1/4 input option. The 1/4 input option may be a little more convenient for most user due to the abundant supply of prefabricated cables on the market. You may also use the two different types of input cables to jump a parallel connection to another amp. For Example: Connect a XLR cable to the input of channel one. You may now connect a 1/4 cable to the input put jack of channel one and jump that cable to the input of another amp.
Unbalanced 1/4 Plug GROUND

XLR MALE SOCKET HOT 3

1 EARTH

XLR Pin Configuration:

US ITT Standard
PIN 1: Ground / Return / 0v PIN 2: Negative data complement (-,Inverted) PIN 3: Positive data (+, inverted)

NON-INVERTING INPUT +

2 COLD DATA IN

Diagram3

Diagram4
V1500 Power Amplifier Instructions page 6

OUTPUTS:

Connect your speakers to the binding post outputs in the rear of the amp. The speaker wire may be connect by bare wire (directly connected usually for permanent connections), banana plug, or spade connector. Connections are made to Channel one and Channel two output for stereo mode or across the red terminals of Channels one and two for Mono Bridge Mode. Important Notice: Although a speaker will operate with the positive and negative leads plugged into either terminal on the amplifier binding post, be sure to plug the negative lead into the black terminal and positive lead into the red terminal. Ensuring proper polarity will avoid your speakers being out of phase, that can cause a loss of bass response.
Bare WIre Connections: (Diagram 5)

When connecting your speakers to the amplifier using bare wire; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps. Strip back the wire insulation 1/2 (13mm). Insert the bare wire into the hole that was reveled by unscrewing the binding post cap. After inserting the wire into the binding post hole, screw the binding post cap down on the wire. To reduce the risk of shock or damage to your amplifier, be sure that the wire connected to one binding post does not come in contact with that of another.
Spade Connector: (Diagram 6)
When connecting your speakers to the amplifier using spade connector; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps. Insert the spade connector in to the binding post and tighten the caps down on the spade connector. To reduce the risk of shock or damage to your amplifier, be sure that the wire connected to one binding post does not come in contact with that of another.
Typical Speaker Output Binding Post. Insert bare wire into the binding post.

Diagram 5

Banana Plug:
When connecting your speakers to the amplifier using banana jacks; Be sure that the red and black caps on the binding post are tighten down completely. Insert the banana jacks into the caps of the binding post, be sure that the banana jack is inserted securely to avoid the risk of it popping out.
Typical Speaker Output Binding Post. Insert spade connector into the binding post and tighten.

Mono Bridge Connections:

Mono bridge operation connections will follow the above descriptions however, when operating in mono bridge operation the speaker connections will run between the two positive (red) leads. Use channel two output for negative and channel one output for positive connection. (See page 8 Diagram 8)

American

Diagram 6
DJ Supply - www.americandj.com -
V1500 Power Amplifier Instructions page 7
Typical Stereo Output Connections

Diagram 7

SPEAKERS 4 OHM MINIMUM

Diagram 8

TYPICAL MONO BRIDGE SET-UP

SPEAKERS 8 OHM MINIMUM

V1500 Power Amplifier Instructions page 8

Typical Stereo Set-Up

Diagram 9

Typical Mixer

V1500 (Rear View)
Typical Speaker Connect to V1500 Channel One Output
Typical Speaker Connect to V1500 Channel Two Output
V1500 Power Amplifier Instructions page 9

NORMAL OPERATION:

Page 9/Diagram9 show you an example of a typical stereo set-up. Connect your inputs into channels one and two of the amplifier. Connect your speakers to the outputs on the rear of the amplifier. Be sure that your front gain controls are turned down to their lowest level (full counter-clockwise). Turn your amp on. Turn your input level up. Use your front gain controls to regulate the output volume. Be sure not to raise the volume to the clip level however, an intermittent clip signal is acceptable.

MONO BRIDGE OPERATION:

Page 8/Diagram 8 give you a description of mono bridge set-up. Be sure you amplifier and all other equipment is shut off. Press the Stereo/Mono switch to the in position (Page 5/Diagram 2 #7). Connect an input signal to channel one. Connect your speaker across the red output binding post on the rear of your amplifier (See Page 7 Mono Bridge Set-Up). Turn your equipment on (your amplifier should be the last piece you turn on). Apply an input signal to your amplifier. Turn channel two gain up. Use the channel one gain to regulate your amplifier output.

PROTECTION:

LIMITER During normal operation, the limiter does not affect the audio signal and is, in fact inaudible. It will allow brief clipping of peaks and will only activate when continuous,hard clipping occurs. The limiter will then reduce the audio signal enough to minimize the amount of clipping. When the signal amplitude decreases enough that clipping ends, the limiter will deactivate and cease its gain reduction. SHORT CIRCUIT PROTECTION The Output Short circuit protects the output devices from short circuits and stressful loads. THERMAL PROTECTION A single variable-speed fan provides adequate cooling. But if the heatsink temperature exceeds 90C., the amplifier will mute until the amplifier cools down. INPUT/OUTPUT PROTECTION The input circuits are isolated by 10k resistors. An ultrasonic network decouples RF from the output and helps keep the amplifier stable with reactive loads.
V1500 Power Amplifier Instructions page 10

SPECIFICATIONS

MODEL NO:
Output Power: 2 ohms, 1 khz 1% THD 4 ohms, 1khz, 1%THD 8 ohms, 1khz 1% THD (Bridge Mode, mono) 4 ohms, 1khz, 1% THD 8 ohms, 1khz, 1% THD

V-1500

N/A 280W RMS PER CH. 200W RMS PER CH. N/A 600 WATTS RMS

V-2000 MKII

540W RMS PER CH. 400W RMS PER CH. 280W RMS PER CH. 1050 WATTS RMS 820 WATTS RMS Less than 0.1%

V-3000

800W RMS PER CH. 600W RMS PER CH. 360W RMS PER CH. 1500 WATTS RMS 1100 WATTS RMS Less than 0.1%

V-4000

1400W RMS PER CH. 1010W RMS PER CH. 600W RMS PER CH. 2500 WATTS RMS 1650 WATTS RMS Less than 0.02%
Total Harmonic Distortion: 20Hz-20kHz, @ rated Less than 0.1% output power, 8 ohms Input Sensitivity and Impedance: @ rated output power, 8 ohms Dimensions & Weight: Height Width Depth Weight Frequency Response: +/- 1db, 1w RMS. 8 ohms +/- 0.2 db, @ rated output, 8 ohms Hum & Noise: Below rated output, 8 ohms Power Consumption: @ rated output power, 8 ohms Cooling System: 1.5v rms

1.0v RMS (0 dBv)

1.75 (4.4cm) 19 (48.3cm) 15.25 (40cm) 25 lbs. (10.5kg) 10 Hz - 40 kHz 20 Hz- 20 kHz 100 dB, unweighted 8A @ 120v AC 1 Dual Speed Fan and Heatsinks
3.5 (8.8cm) 19 (48.3cm) 15.9 (40.5cm) 30 lbs. (13.6kg) 10 Hz - 40 kHz 20 Hz - 20 kHz 100 dB, unweighted 7A @ 120vAC 2 Dual Speed Fans and Heatsinks
3.5 (8.8cm) 19 (48.3cm) 15.9 (40.5cm) 31 lbs. (14 kg.) 10 Hz- 40 kHz 20 Hz- 40 kHz 100 dB, unweighted 10A @ 120vAC 2 Dual Speed Fans and Heatsinks
5.25 (13.3cm) 19 (48.3cm) 15.9 (40.5cm) 61.7 lbs. (28 kg.) 10 Hz- 40 kHz 20 Hz- 40 kHz 100 dB, unweighted 40A @ 120vAC 2 Dual Speed Fans and Heatsinks
V1500 Power Amplifier Instructions page 11
American Audio American DJ Group of Companies World Headquarters: 4295 Charter Street Los Angeles, CA 90058 USA Tel: 323-582-2650 / Fax: 323-582-2610 web: www.americandj.com / e-mail: info@americandj.com

www. AmericanAudio.u s

designed for the

Working DJ.

CONTENTS
05 CD PLAYERS 12 MIXERS 17 TURNTABLES 19 TT-CARTRIDGES 20 AMPLIFIER 22 SPEAKER 23 CROSSOVERS / EQs 24 RACKS & CASES 30 FOR THE RACK 31 ACCESORIES 32 CABLES 34 ACCESORIES 35 MICROPHONE

product catalog: 03/03

The actual performance of the jog wheel is exemplary, with it being suitably sensitive and giving you an excellent spin for pulling off rewinds and crazy effects. - iDJ (UK)

PS CASE

. Heavy duty roadcase for one Pro-Scratch2 or PSX. CD Player sold separately Code: 185100

PRO-SCRATCH2

MAIN FEATURES
. PowerTouch Wheel*: Touch sensitive interactive jog wheel. 2 Scratching modes: Digital Scratch mode & Beat Juggle mode. On-board FX: Scratch, Filter, Echo, Trans, Skid, Phase, Flanger, Pan & Bop. Digital Output - S/PDIF. Tempo Lock (Master Tempo). Store 384 cue points or samples. Pitch Bend: +/-4%, +/-8%, or +/-16%. Hyper Pitch (up to +/-100%). 3 Flash Start Sampler Buttons. Anti-shock memory (10 seconds). Seamless loop. Fader Q Start. Reverse play I took the old American Pros (Pro-Scratch1) on tour last year across America,. Reads CDs & CD-R discs and they were really good to work and travel with. All these feature advances really. Slot load make the Pro Scratch 2s a pleasure to use. An excellent follow-up from the team! Code: 100003 The CD mixer war is defiantly on - CARL COX (www.trustthedj.com)
+/- 0,5dB 20Hz - 20kHz 82 dB 84 dB 0.02% 2.0V +/- 1dB AV 115V 60Hz / 230V 50Hz 217 x 82 x 306 mm 2,5 kg

PS SYS CASE

PS SYS CASE. Heavy duty roadcase for the Pro-Scratch2 system. Also fits PSX Player. Fits most 2-channel and 3-channel mixers. Equipment sold separately Code: 185102
frequency response: channel separation: S/N ratio: total harmonic distortion: output level: power supply: dimensions (LxHxW): weight:

www.AmericanAudio.us

CD PLAYERS
. PowerTouch* , Touch sensitive interactive jog wheels. Digital Scratching 2.0 (Accurate Scratching). 2 Scratching modes: Digital Scratch mode, Beat Juggle mode. 9 On-board FX: Scratch, Filter, Echo, Trans, Skid, Phase, Flanger, Pan, Bop. Effect layering. Digital B.P.M. counter: keeps digital FX in sync with music. 6 Preset Parameters settings for each FX. Tempo Lock (Master Tempo). Lock out mode (Security feature). Parameter Ratio adjustment knob. Parameter Time adjustment knob. Pitch Bend: +/-4%, +/-8%, or +/-16%. Hyper Pitch (up to +/-100%). 3 Flash Start Sampler Buttons per side (7 second sample per button with or without a CD in drive). Flash Cue. Slot Load Dual CD Player. Digital Anti-shock memory: 10 seconds per side. Instant start. Seamless loop. Fader Q Start. Reverse play. Digital output - S/PDIF

VELOCITY

ADDITIONAL FEATURES
. Volume control between music and sampler. FX MIX. Auto cue. Store 384 cue points or samples. Single/continuous play. Flip Flop (Relay playback between two decks). Headphone output with volume control. Reads CDs and CD-R discs Code: 105007
frequency response: S/N ratio: total harmonic distortion: output level: power supply: power consumption: over sampling rate: D/A Conversion: Sampling Rate: Anti-Shock Memory: dimensions (main unit): dimensions (control unit): weight total: +/- 1dB 20Hz - 20kHz -85 dB 0.03% 2.0V +/- 1dB AV 115V 60Hz / 230V 50Hz 35W 8 times 1 bit 44,1 k 10sec. per side 482 x 88,8 x 251 mm / 2 rack spaces / x 177 x 52 mm / 4 rack spaces / 19 7,2 kg
*(U.S. & foreign patends pending)
The Velocity is one of the most powerful digital turntables to date; the first rack mount style CD player I actually enjoy working on. - Gerald World Wide Webb, founder of www.DigitalScratch.com

DCD-PRO600

. Tempo Lock (Master Tempo). 7 On-board digital FX: 2 Filter, 2 Coast, Reverse Play, BOP. DSP Technology. 20 seconds of Digital Anti-Shock memory per side. 30 programmable tracks. Seamless Loop frequency response:. Fader Q Start channel separation:. Digital output S/PDIF S/N ratio:. Pitch control: +/- 8%, +/- 12% or +/- 16% total harmonic distortion: output level:. Reads CDs and CD-R discs power supply:. Flip Flop dimensions (cd player): dimensions (remote contr.): Code: 105006
weight (cd player): weight (remote contr.):
+/- 1dB 20Hz - 20kHz, 0 dB 80 dB 88 dB 0.02% 2.0V +/- 1dB AV 115V 60Hz / 230V 50Hz 482 x 89x 254mm / 2 rack spaces 482 x 74 x 132mm / 3 rack spaces 5,0 kg 2,0 kg
. Seamless Loop. Fader Q Start. Selectable Pitch Control (+/-8%, +/-12% or +/-16%). Direct track access buttons. Tap sync. beat counter. Digital Output - S/PDIF. 10 programmable cue points. Instart Start. Flip Flop. Reads CDs and CD-R discs Code: 105003 08
frequency response: channel separation: S/N ratio: total harmonic distortion: power consumption: sampling rate: D/A conversion: search accuracy: output level: power supply: dimensions (cd player): dimensions (remote contr.): weight (total): +/- 1dB 20Hz - 20kHz, 0 dB 88 dB 88 dB 0.02% 25W 44,1 kHz 16 bit 1/75 sec. 2.0V +/- 1dB AV 115V 60Hz / 230V 50Hz 482 x 89 x 264mm / 2 rack spaces 482 x 132 x 74mm / 3 rack spaces 7,0 kg

. 20 Seconds of Anti-Shock Protection. Seamless Loop. Fader Q Start. Digital output - S/PDIF. FX: Reverse Play, Skid, Coast & Bop. 4 Cue Hot Start Buttons. +10 Track Advance Button. Reads CDs & CD-R discs Code: 100002

PRO-DJ2FX

DIGITAL EFFECTS
MAIN FEATURES. Feather Fader Plus for Q-Start Control. 3 Phono, 4 Line, 3 Auxiliaries & 3 Mic Inputs. Balanced output, Rotary Kills. High Quality Feather Fader for smooth, clean cross fades (replaceable). Bass, Mid and Treble for each channel. 2 Independent Microphones with Separate EQ with combo connection (1/4/XLR) - 3rd Mic on channel 4. Zone Output with Bass and Treble Control. Mono/Stereo Switche on Master. High level headphone output. Cue Mixing. Split cue for headphones. Auto mute. Talk over Button - Reduces channel output Gain by 15dB +/- 2dB. Pre Fader Levels (PFL) for each channel. On/Off switch for channel assign

Q-FX19

. Digital output. Gain control for each channel. Independent light control output for touch panels and chase controllers. Rear inset L shape case design. 120V/220V selectable. Q-Start Compatible (for use with American Audio CD Players with Fader Q Start). Fader Q Start on channels 1 & 2. 2 year limited warranty. Hight output to headphones Light Control Signal Output Jack. Dual Stereo LED Level Indicator - Indicated Master Level. Master Output Pan Control. Balanced XLR Output. DSP Effects - Trans, Pan Filter, Pitch Shift, Flanger, Phase, Echo and Delay. Digital BPM Display

Code: 125012

headphone impedance: distortion: channel EQ: power supply: dimensions (LxHxW): weight (total): CROSSFADER:
16 Ohm >0.03% -35dB - +15dB for bass, mid & treble AV 115V 60Hz / 230V 50Hz 482 x 266 x 105mm / 19z 5,1 kg Featherfader Plus
. 8 lines, 2 phono, 2 mic inputs. 4 channels with rotary knobs and individual LED indicators. Separate Balanced Outputs: Master Outs; Booth Outs; Subwoofer Outs. 4-band rotary EQ: Bass, Mid Low, Mid High, Treble. Feather Fader crossfader. Fader Q Start with On/Off. Adjustable subwoofer frequency control. Recessed case design Code: 125003
power supply: dimensions (LxHxW): weight: AV 115V 60Hz / 230V 50Hz 114 x 178 x 482 mm / 19 2,3 kg 4 r.m. spaces

Q-2422SX

Q-3433SX
MAIN FEATURES MAIN FEATURES
. 2 phono, 4 line, 2 auxiliaries & 2 mic inputs. 3-Channels. Fader Q Start. Balanced XLR Outputs. Pan and Gain control for each channel. Bass, mid and treble control for each channel. Zone volume, treble and bass control Code: 125006

S/N ratio: Talkover: frequency range: headphone impedance: distortion: channel EQ: power supply: dimensions (LxHxW): weight (total): CROSSFADER: >80 dB -15 dB +/- 2dB 20Hz - 20kHz, +/- 1dB 16 Ohm >0.03% -35dB - +15dB for bass, mid & treble AV 115V 60Hz / 230V 50Hz 482 x 176 x 65mm / 19z 3,8 kg Featherfader Plus 4 r.m. spaces
. 3 phono, 4 line, 3 auxiliaries & 3 mic inputs. 4-Channels. Fader Q Start. Balanced XLR outputs. Bass, mid & treble control for mics. Combination microphone connection. Bass, mid, treble and gain control for each channel. 3 independent outputs Mater, Zone, & Booth. Zone with treble and bass control Code: 125007
S/N ratio: Talkover: frequency range: headphone impedance: distortion: channel EQ: power supply: dimensions (LxHxW): weight (total): CROSSFADER:
>80 dB -15 dB +/- 2dB 20Hz - 20kHz, +/- 1dB 16 Ohm >0.03% -35dB - +15dB for bass, mid & treble AV 115V 60Hz / 230V 50Hz 482 x 266 x 93mm / 19 4,4 kg Featherfader Plus 6 r.m. spaces

MIXERS

. 6 lines, 2 phono, 2 mics. 4-Channels. Balanced XLR outputs. 4-band EQ: Bass, Mid Low, Mid High, Treble Code: 125002
power supply: dimensions (LxHxW): weight (total):
AV 115V 60Hz / 230V 50Hz 482 x 114 x 178mm / 19 2,3 kg 4 r.m. spaces

Q-3633 SX Commander

S/N ratio Line/AUX: S/N ratio Mic: S/N ratio Phono: Talkover: frequency range: headphone impedance: distortion: channel EQ: power supply: dimensions (LxHxW): weight (total): CROSSFADER: >70 dB >55 dB >85 dB -15 dB 20Hz - 20kHz, +/- 1dB 16 Ohm >0.03% -30dB - +20dB for bass, mid & treble AV 115V 60Hz / 230V 50Hz 482 x 176 x 76mm / 19 2,8 kg FF-Plus 4 r.m. spaces

Q-SPAND

. 3 phono, 6 line, 3 microphone inputs & 3 auxiliaries. 4-Channels. Fader Q Start. Balanced XLR outputs. Bass, mid, treble and gain for each channel. 2 independent microphones. 2 zones with bass and treble (3 total zones). FX send & receive for every channel including independent mics Code: 125004
power supply: dimensions (LxHxW): weight (total): AV 115V 60Hz / 230V 50Hz 482 x 89 x 267mm / 19 5,3 kg 6 r.m. spaces
. 3 Phono, 4 Lines, 3 Auxiliaries & 3 Mics. 4-channels. Fader Q Start. WOW by SRS button - SonicEnhancer with 3 dimensional sound. Bass, mid, treble and gain for each channel. Balanced XLR outputs. Zone volume knob Code: 125010
. 2 Phono, 2 Lines, 2 Aux & 1 Mic input. Fader-Q-Start w/ On/Off control for each channel. 3 position Fader Curve Switch Normal to Quick Fade (for crabbing). Hamster Switch. Gain, Treble, Mid & Bass control for each channel. 2 separate headphone outputs. 100% cut buttons for Treble, Mid & Bass Code: 125001

OPTTICAL CROSSFADER

DJ SKILZ
If DJs like to use a crossfader that feels like butter, then let me tell you rst-hand that this crossfader (Q-D5) will melt in your hands! - DJ Skilz

SIGNATURE SERIES MIXER

. 2 Phono, 2 Lines, 2 Aux ^ 1 Mic input. Optical Crossfader (tested over 1 milion times)*. Balanced XLR outputs. Fader Q Start. Cross Fader curve knob (short to long crossfade) with reverse crossfade button. Independent curve for channels 1 ^ 2 (short to long curve) with reverse button. Gain, Treble, Mid ^ Bass control for each channel. -30 dB Rotary Kills for Treble, Mid ^ Bass. 100% cut buttons for Treble, Mid ^ Bass Code: 125008
*The optical fader was factory tested over 1 million times back-and-forth and never quite working!
S/N ratio Line/AUX: S/N ratio Mic: S/N ratio Phono: Talkover: frequency range: headphone impedance: distortion: channel EQ: power supply: dimensions (LxHxW): weight (total): CROSSFADER:
>65 dB >55 dB >60 dB -15 dB 20Hz - 20kHz, +/- 2dB 16 Ohm >0.03% -30dB - +20dB for bass, mid & treble AV 115V 60Hz / 230V 50Hz 262 x 320 x 102mm 3,5 kg FF-Plus
AV 115V 60Hz / 230V 50Hz 254 x 82,5 x 311mm 3,0 kg
The unit (Q-D5) has the fastest and smoothest feel of any mixer I have experienced. The crossfader ies back and forth as if oating on air. - Orion Ray-Jones, Mixer Magazine

XDM-200

. 2 Phono,2 lines & 1 x mic. Low residue resistanced Crossfader Code: 125011
frequency range: distortion: cross talk: power supply: power consumption: dimensions (LxHxW): weight (total): 20Hz - 20kHz, +2, -3dB <0,2% >50dB 1kHz AC 9V/500 mA /transformer included) 9 Watts Typical 236x 192x 82mm 2,8 kg

Q-MX2BPM

. 3 Phono,4 lines & 3 mic inputs. Auto BPM Display. Fader Q Start. Balanced XLR outputs. Treble, Mid, Bass and Gain for each channel. Selectable Crossfader curve. XLR / 1/4 combo mic connector. 2 headphone outputs. 100% cut buttons for Treble, Mid & Bass. Trans FX Code: 125009
S/N ratio Line/AUX: S/N ratio Mic: Talkover: frequency range: headphone impedance: distortion: channel EQ: power supply: dimensions (LxHxW): weight (total): CROSSFADER: >63 dB >54 dB -15 dB +/- 2dB 20Hz - 20kHz, +/- 1dB 16 Ohm >0.03% -30dB - +20dB for bass, mid & treble AV 115V 60Hz / 230V 50Hz 280 x 310 x 78mm 4,0 kg Featherfader Plus
. 2 Phono, 2 Lines, & 1 Mic inputs. Fader-Q-Start w/ On/Off control for each channel. Fader Curve Switch Normal to Quick Curve. Treble & Bass control for each channel. Feather Fader cross fader Code: 125005

Ortofon Set Concorde-Pro

Code: 135121
Ortofon Set Concorde Night-Club E

Code: 135125

BANANA/STYL
. One replacement stylus for the Banana cartridge Code: 135002
Ortofon Set Concorde-DJ S

Code: 135122

Ortofon Set Concorde Scratch

Code: 135126

Ortofon Set Concorde-DJ E

Code: 135123

Code: 135124

TT-CARTRIDGES

CONCORDE-SYSTEMS

AMPLIFIERS

In a Best bang for the buck shootout, the American Audio V4000plus came out on top of two very major players. If youre considering a higher output amplifier, you owe it to yourself and your wallet to consider this amp! www.ProDJ.com

Output Power

GX-300
N/A 150W RMS per channel 100W RMS per channel N/A 300W RMS per channel Less than 0.1%

V1000PLUS

315W RMS per channel 245W RMS per channel 170W RMS per channel 600W RMS per channel 510W RMS per channel Less than 0.1%
N/A 280W RMS per channel 200W RMS per channel N/A 600W RMS per channel Less than 0.1%

V2000PLUS

650W RMS per channel 450W RMS per channel 280W RMS per channel 1290W RMS per channel 900W RMS per channel Less than 0.1%

V3000PLUS

960W RMS per channel
690W RMS per channel 440W RMS per channel 1930W RMS per channel 1450W RMS per channel Less than 0.1%

V4000PLUS

1400W RMS per channel 1010W RMS per channel 600W RMS per channel 2500W RMS per channel 1650W RMS per channel Less than 0.02%

V5000PLUS

1900W RMS per channel 1300W RMS per channel 800W RMS per channel 3000W RMS per channel 2100W RMS per channel Less than 0.02%
2 ohms, 1 khz 1% THD 4 ohms, 1 khz 1% THD 8 ohms, 1 khz 1% THD (Bridged Mode, mono) 4 ohms, 1 khz 1% THD 8 ohms, 1 khz 1% THD
Total Harmonic Distortion (THD)
20Hz-20kHz, @ rated output power, 8 ohms
Input Sensitivity ^ Impedance
@ rated output power, 8 ohms

Dimensions ^ Weight

.775v rms (0 dBv) 3.5 (88cm) 19 (48.3cm) 8.86 (220.cm) 16.3 lbs. (4.1 kg.) 10Hz - 40 kHz 20Hz - 20 kHz 100 dB, unweighted >100dB
1.0v rms (0 dBv) 3.5 (8.8cm) 19 (48.3cm) 15.9 (40.5cm) 26.4 lbs. (12 kg.) 10Hz - 40 kHz 20Hz - 20 kHz 100 dB, unweighted unweighted, 55 dB A weighted 90v/usec 240 DC output protection, Overload protection, Short circuit protection, On & Off protection Front panel reset

1.5v rms (0 dBv) 1.75 (4.4cm) 19 (48.3cm) 15.25 (40.cm) 25 lbs. (10 kg.) 10Hz - 40 kHz 20Hz - 20 kHz 100 dB, unweighted unweighted, 60 dB A weighted 90v/usec 240 DC output protection, Overload protection, Short circuit protection, On & Off protection Front panel reset
1.0v rms (0 dBv) 3.5 (8.8cm) 19 (48.3cm) 15.9 (40.5cm) 30 lbs. (13.6kg.) 10Hz - 40 kHz 20Hz - 20 kHz 100 dB, unweighted unweighted, 60 dB A weighted 90v/usec 240 DC output protection Overload protection, Short circuit protection, On & Off protection Front panel reset 2 limiters - 1 per channel 2 HP lters 30Hz, 50Hz
1.0v rms (0 dBv) 3.5 (8.8cm) 19 (48.3cm) 15.9 (40.5cm) 31 lbs. (14kg.) 10Hz - 40 kHz 20Hz - 20 kHz 100 dB, unweighted >100dB
1.0v rms (0 dBv) 5.25 (13.3cm) 19 (48.3cm) 15.9 (40.5cm) 61.7 lbs. (28kg.) 10Hz - 40 kHz 20Hz - 20 kHz 100 dB, unweighted >100dB
1.08v rms (20K Ohm) 3.5 (8.8cm) 19 (48.3cm) 17.5 (44.6cm) 67 lbs. (25kg.) 10Hz - 40 kHz 20Hz - 20 kHz 100 dB, unweighted >100dB
Height Width Depth Weight

Frequency Response

1dB, 1W RMS 8 ohms 0.2dB, @rated output, 8 ohms

Hum ^ Noise

Below rated output, 8 ohms

Signal to Noise Ratio

Slew Rate

20v/usec

Damping Factor @ 8
25v/usec 400 DC output protection Overload protection, Short circuit protection, On & Off protection Sub-Woofer Crossover
25v/usec 400 DC output protection Overload protection, Short circuit protection, On & Off protection Sub-Woofer Speakon Plugs LED Mode Indicator
20v/usec 300 DC output protection Overload protection, Short circuit protection, On & Off protection

>200 @ 1Khz

Protection Circuit
DC output protection, Overload protection, Short circuit protection,

Special Features

Power Consumption

Turn-On Thump Protection

5A @ 110V AC

5A @ 120V AC Yes

8A @ 120V AC Yes 1 Dual speed fan & heatsink
7A @ 120V AC Yes Dual 2 speed fans & heatsink
10A @ 120V AC Yes 2 dual speed fan & heatsink

20A @ 120V AC Yes 2 dual speed fan & heatsink

Cooling System

Variable speed fan
Dual 1 speed fans & heatsink
NOTE: 1 Rackspace = Approx. 1.75 Code: 150001 Code: 150002 Code: 150003 Code: 150004 Code: 150005 Code: 150006 Code: 150007 21
Sub-Woofer Speakon Plugs LED Mode Indicator

SPEAKERS

APX-POWER PRO

APX-122

APX-152

SPECIFICATIONS

. 2-way speaker with 12 woofer and 1 compression driver. POWER: 300W total - 250W to woofer, 50W to horn. Built-in socket for stand. Rugged lightweight plastic cabinet with handle. Dual 1/4 and dual Speakon inputs. Frequency response (-3dB): 60Hz-15 kHz. Frequency response (-10dB): 55Hz-19 kHz. Driver quantity: Bass 15 x 1, Treble ED4401X1. Nominal Dispersion: 90 x 50 (HXV). Impedance: 8 Ohm. Power: 225W power handling - 900W peak power (@ 8 ohms). Sensitivity: 96 dB/1W/1m. Dimensions: 59 x 43 x 32 cm. Weight: 18 kg Code: 165001
. 2-way speaker with 15 woofer and 1 compression driver. POWER: 300W total - 250W to woofer, 50W to horn. Built-in socket for stand. Rugged lightweight plastic cabinet with handle. Dual 1/4 and dual Speakon inputs. Frequency response (-3dB): 60Hz-15 kHz. Frequency response (-10dB): 45Hz-18 kHz. Driver quantity: Bass 15 x 1, Treble ED4401X1. Nominal Dispersion: 90 x 50 (HXV). Impedance: 8 Ohm. Power: 225W power handling - 900W peak power (@ 8 ohms). Sensitivity: 96 dB/1W/1m. Dimensions: 69 x 45 x 36 cm. Weight: 23,8 kg Code: 165002
. 2-way speaker with 15 woofer and 1 compression driver. POWER: 300W total - 250W to woofer, 50W to horn. XLR line & parallel inputs. Built-in 1 1/2 pole socket for stand. Built-in H Class design bi-amplifier system. Rugged lightweight plastic cabinet with handle and hanging hardware -3 fly points for hanging. 1/4 stereo microphone input with mic volume control. Line input control. Treble & bass adjustment knobs. Master volume control. Low cut switch (cuts bass). Power switch
.Heavy duty bolt for securing speakers
. Frequency response (-3dB): 60Hz-15 kHz. Frequency response (-10dB): 45Hz-18 kHz. Driver quantity: Bass 15 x 1, Treble ED4401X1. Nominal Dispersion: 90 x 50 (HXV). Impedance: 8 Ohm. Sensitivity: 96 dB/1W/1m. Connecting jack: XLR. Dimensions: 17.72 x 14.17 x 27.17. Weight: 55 lbs. Code: 165003

Code: 165100

Z-APX/H
.Heavy duty eye-hook for suspending speakers Code: 165101

SPS-1B

. Rugged gig bag with rollers, adjustable handle & heavy duty zipper. Move speakers with ease. Fits: APX-152, APX-Power Pro & various other brand speakers Code: 185200

Z-APX/B

. Sturdy Aluminum speaker stand tripod. 80 pound capacity with socket mounting bracket to attach to speaker. Recommended maximum height is 6 ft. Weight: 2,5 lbs. Pipe diameter: 1 3/8 Code: 170001
. 4th Order linkwitz-Riley electronic crossover. 2-way stereo / 3-way mono. Floating & balanced Inputs & Outputs. CD BOOST electronic circuitry. Clip LED to indicate distortion. Low & High mute buttons. Low/Mid/High phase inversion switch. Dimensions: 1 r.m. space. Weight: 6 lbs. Code: 155001
frequency response: S/N ratio: max. output level: power supply: dimensions (LxHxW): weight:
+/- 0,5dB 10Hz - 20kHz 11 dB RL > 2kOhm +21dBu (6.2V) AV 115V 60Hz / 230V 60Hz 482 x 171 x 44mm / 19 5,0 kg

XEQ-152

. 2 channel 15 2/3 octave band graphic equalizer. 25Hz - 16kHz frequency control. Constant Q circuitry (3% frequency accuracy). Selectable 6dB or 12dB control. Variable level control. By-pass switch. Overload threshold. Ground lift switch. XLR & 1/4 TRS balanced Inputs/Outputs. Dimensions: 1 r.m. space. Weight: 4.5 lbs. / 2.5 kg Code: 155002

XEQ-312

. 2 Channel 31 1/3 Octave Band Graphic Equalizer. 25Hz - 16kHz frequency control. Constant Q circuitry (3% frequency accuracy). Selectable 6dB or 12dB control. Variable level control. By-pass switch. Overload threshold LED (5dB below clipping). Ground lift switch. XLR & 1/4 TRS balanced Inputs/Outputs. Power: AC 115V 60Hz / 230V 50Hz switchable. Dimensions: 2 r.m. space. Weight: 9 lbs. Code: 155003
frequency response: range: max. output level: channel separation: output impedance: S/N ratio: total harmonic distortion: power supply: dimensions (LxHxW): weight: +/- 0,5dB 20Hz - 20kHz +/- 6dB / +/- 12dB 22dBm 50dB 600 Ohm 101 dB <0.01% AV 115V 60Hz / 230V 50Hz 482 x 216 x 44mm / 19 2,5 kg

frequency response: range: max. output level: channel separation: output impedance: S/N ratio: total harmonic distortion: power supply: dimensions (LxHxW): weight:
+/- 0,5dB 20Hz - 20kHz +/- 6dB / +/- 12dB 22dBm 50dB 600 Ohm 101 dB <0.01% AV 115V 60Hz / 230V 50Hz 482 x 264 x 88mm / 19 5,0 kg

CROSSOVERS / EQs

XCR-232

RACKS & CASES

PRO-DJ/CASE/AL19
PS SYS CASE PRO-DJ/CASE/AL
. Heavy duty roadcase for the Pro-Scratch2 system. Also fits PSX Player. Fits most 2-channel and 3-channel mixers. Equipment sold separately Code: 185102
. Custom case for Pro-DJ1,2 & 3 systems. Aluminum railing for added protection. Uniquely designed hinged doors that protect transport trays. Very lightweight. Use with 19 mixers. Dimensions: 37 W x 16.5 D x 8.5 H. Weight: 20 lbs. Equipment not included Code: 185122
. Custom case for Pro-DJ, Pro-DJ2FX. Aluminum railing for added protection. Uniquely designed hinged doors that protect transport trays. Very lightweight. Use with 10 mixers. Dimensions: 28 L x 17.5 W x 8.5 H - 711.2 x 444.5 x 215.9 mm. Weight: 18lbs. / 8.17kg. Equipment not included Code: 185123
MAIN FEATURES. Heavy duty roadcase for one
Pro-Scratch2 or PSX. CD Player sold separately Code: 185100
. Top load Amp Rack combo. 19 inch rack mount: 6 spaces Top, 2 spaces Bottom. Made of lightweight, durable plastic. Convenient, easy to carry handles. Rugged roadworthy construction: 3 detachable lids (top, front and back) with lock tight latches. Makes for a very lightweight, compact mobile DJ system. Equipment not included Code: 185131

PRO-SCRATCH/CASE

. Custom case for Pro-Scratch systems. Aluminum railing for added protection. Uniquely designed hinged doors. Very lightweight. Use with Q-MX mixers. Dimensions: 30 L x 6.5 W x 16.5 H - 762 x 165.1 x 419.1 mm. Weight: 12.4lbs. / 5.63kg. Equipment not included Code: 185124
TLC Cases are lightweight, durable & ready for the road!

TLC-6x2

. Top load Amp Rack combo. 19 inch rack mount: 10 spaces Top, 6 spaces Bottom. Made of lightweight, durable plastic. Convenient, easy to carry handles. Rugged roadworthy construction: 3 detachable lids (top, front and back), with lock tight latches. Equipment not included Code: 185130

TLC-10x6

NEW. Top load Amp Rack combo. 19 inch rack mount: 7 spaces Top, 2 spaces Bottom. Made of lightweight, durable plastic. Convenient, easy to carry handles. Rugged roadworthy construction: 3 detachable lids (top, front and back) with lock tight latches. Makes for a very lightweight, compact mobile DJ system. Shown with lids attached. Code: 185132 25

TLC-7x2

NEW. Durable DJ Roadcase for vinyl records & CDs. Approximate capacity: 70 LP records & 60 Jewel Cases or 180 View Packs. Lock type latch with key on CD case only. Heavy-duty wheels and pull-up handle. Extra slot to hold accessories. Available in Brushed Swirl chrome finish Code: 185103

PROTEK LP TRANSPARENT

PROTEK CDLP
. Transparent Durable DJ Roadcase for vinyl records. Approximate capacity: 70 LP records. Comes in Clear acrylic Code: 185117
Finally a case for DJs that use both vinyl and CD formats!

Equipment not included

. Vinyl/LP durable hardcase for vinyl records. Approximate capacity: 70 records. Available colors: Black, Silver, Blue & Red Code: 185112 Code: 185116 Code: 185113 Code: 185115 Black Silver Blue Red

PROTEK LP DIA W

PROTEK LP
. Durable DJ Roadcase for vinyl records. Approximate capacity: 70 LP records. 2 extra pockets to hold headphones & accessories. Zipper pouch on lid. Snap pouch on rear. Heavy-duty wheels and pull-up handles. Available in Chrome Diamond Plate Code: 185114
Equipment not included 26
. Durable turntable hardcase. Fits one American Audio or other popular turntable brands. Available colors: Black, Silver, Blue & Red. Equipment not included Code: 185118 Code: 185121 Code: 185119 Code: 185120 Black Silver Blue Red

PROTEK TT PRO

PROTEK TT
. Heavy duty turntable hardcase with sturdy brackets and ball corners. Fits one American Audio or other popular turntable brands. Available colors: Black only. Equipment not included Code: 185125
. Durable roadcase for CDs and accessories. Aluminum CD case for 60 Jewel cases or 180 View Packs. Lock type latch with key. Available colors: Black, Silver, Blue & Red. CDs sold separately
. Durable roadcase for CDs and accessories. Aluminum CD case for 200 Jewel cases or 600 View Packs. Heavy duty wheels and pull-up handle. Lock type latch with key. Available in Black and Silver. CDs sold separately
. Durable roadcase for CDs and accessories. Aluminum CD case for 100 Jewel cases or 300 View Packs. Lock type latch with key. Available colors: Black & Silver. CDs sold separately
Code: 185106 Black Code: 185107 Silver
Code: 185104 Black Code: 185105 Silver
Code: 185108 Code: 185111 Code: 185109 Code: 185110

Black Silver Blue Red 27

PROTEK CD600

PROTEK CD300

PROTEK CD

RACKPANEL 19 closed

RACKPANEL 19 open Roller-Rack
. 185060 RACKPANEL EP-1U, 1 R.M.S. closed. 185061 RACKPANEL EP-2U, 2 R.M.S. closed. 185062 RACKPANEL EP-3U, 3 R.M.S. closed. 185063 RACKPANEL EP-4U, 4 R.M.S. closed
. 185064 RACKPANEL EP-1U, 1 R.M.S. open. 185065 RACKPANEL EP-2U, 2 R.M.S. open. 185066 RACKPANEL EP-3U, 3 R.M.S. open. 185067 RACKPANEL EP-4U, 4 R.M.S. open

L-RACKS 19

. 185050 Roller-Rack 10HE
. 185001 RACK Flight-Pro 3+12 R.M.S., heavy brown. 185002 RACK Flight-Pro 5+12 R.M.S., heavy brown. 185003 RACK Flight-Pro 6+12 R.M.S., heavy brown. 185004 RACK Flight-Pro 8+12 R.M.S., heavy brown. 185005 RACK Flight-Pro 10+12 R.M.S., heavy brown. 185006 RACK Flight-Pro 14+12 R.M.S., heavy brown

STANDARD

DOUBLEDOOR-RACKS 19
. 185007 RACK Flight-Pro 2 R.M.S., standard brown. 185008 RACK Flight-Pro 3 R.M.S., standard brown. 185012. 185013. 185014. 185015 RACK Flight-Pro 4 R.M.S., heavy brown RACK Flight-Pro 5 R.M.S., heavy brown RACK Flight-Pro 6 R.M.S., heavy brown RACK Flight-Pro 8 R.M.S., heavy brown
. 185009 RACK Flight-Pro 10 R.M.S., heavy brown. 185010 RACK Flight-Pro 11 R.M.S., standard brown. 185011 RACK Flight-Pro 20 R.M.S., standard brown

FOR THE RACK

. 7 protected switched A/C grounded outlets on rear of unit, & 1 A/C unswitched outlet on rear of unit. 1 A/C outlet switched on front of panel. 10A per outlet/16A protection breaker button on front panel. Master on/off switch. Dual pop-out lights with dim control knob. Great for lighting up DJ booths. Protection: 16A breaker. Power 120V or 220V operation. Weight: 2,5 kg. 1 rack mount space Code: 180014
. 7 protected switched A/C grounded outlets on rear of unit, & 1 A/C unswitched outlet on rear of unit. 1 A/C outlet switched on front of panel. 10A per outlet/16A protection breaker button on front panel. Digital voltage meter. Master on/off switch. Dual pop-out lights with dim control knob. Great for lighting up DJ booths. Protection: 16A breaker. Weight: 2,5 kg. 1 rack mount space. Power surge & spike protector with A/C filter for unwanted RFI noise Code: 180015

GNL-1019

. 19 inch rack mount single Goose Neck Light. 14 inch Goose Neck can be positioned in almost any direction. Great for lighting up DJ consoles. Knob to dim light. Includes power supply. Single space rack mount. Weight: 0,3 kg Code: 180016

Soon available in silver

dB-DISPLAY
. Designed to set in an amp rack to view your decibel level. Creates a great light show in your amp rack. Display progresses from green through amber to red. Sensitivity adjustment on both left and right channels. 2 separate modes: dot and bar. Includes a 12V power supply. Power Supply: 12V DC. Line Inputs: Left & Right RCA. Line Outputs: Left & Right RCA. 1 rack mount space. Weight: 1,2 kg Code: 180022

GNL-2019

. 19 inch rack mount dual Goose Neck Lights. 14 inch Goose Necks can be positioned in almost any direction. Great for lighting up DJ consoles. Knob to dim lights. Includes power supply. 1 rack mount space. Replacement Lamp: ZB-GNL Code: 180017
. Feather Fader is a replaceable, universal crossfader designed for all PROformer Series, PROformer Plus and Q-Series mixers. Provides smooth and quick mixing transitions between channels. Our high quality crossfader is put into every mixer, unlike other companies, who sell it as an option!. Alps fader made in Japan

FEATHER FADERS

XDM-221 XDM-241 XDM-343 XDM-352 XDM-3633 Code: 9910009
XDM-221 XDM-241 XDM-343 XDM-352 XDM-3633, XDM-250T Code: 9910008

XDM-221 Code: 9910007

Q-2221 Code: 9910006
Q-2422/S Q-3433/S Code: 9910005

FF-PLUS

FF-5/S

FF-PLUS/S

Q-2422/S Q-3433/S Code: 9910002
Q-2221/SX XDM-250 Q-2221/SX, Q-2422/SX Q-3433/SX, Q-221, Q-D3 Code: 9910011
Q-MX1 Q-MX2BPM Q-SPAND Code: 9910001

DX4 DX5R Code: 9910004

Q-D5 Code: 9910010

GNL-14

. GNL-14, Gooseneck Light allows you to perform in dimly lit areas. 14-inch flexible gooseneck fits the American DJ mixers with XLR connection. Comes with one lamp. Replacement lamp: Model: ZB-GNL. Connection: 12V DC BNC Code: 180018

Mini-Light

180044 180045
Mini-Light universel with transformator Mini-Light BNC with raylight Mini-Light BNC without raylight Mini-Light XLR with raylight Mini-Light XLR without raylight Sparelamp for Mini-Light

Mini-Light with raylight

Mini-Light without raylight

ACCESSORIES

FF-4/S

Plugs / Connectors

Adapters

Jack cables 6,3mm

. 392001 Adapter jack 3,5mm to 6,3mm plug. 392002 Adapter female/female for plug Speakon
. 387060. 387061. 387062. 387063. 387064. 387065
cable jack 6,3mm mono, 5m, male male cable jack 6,3mm mono, 20m, male male cable jack 6,3mm stereo, 5m, male male cable jack 6,3mm stereo, 10m, male male cable jack 6,3mm stereo, 20m, male male cable jack 6,3mm mono jack 2x1
. 392100. 392101. 392102. 392103. 392104. 392105. 392106. 392107. 392108. 392117. 392109. 392110. 392111. 392112. 392113. 392114. 392115. 392116
plug XLR 3pol female black plug XLR 3pol female blue plug XLR 3pol female yellow plug XLR 3pol female red plug XLR 3pol male black plug XLR 3pol male blue plug XLR 3pol male yellow plug XLR 3pol male red fitting connector female 3pol XLR metal black fitting connector male 3pol XLR metal, black plug Speakon 4pol Neutrik NC 3 MX Neutrik NC 3 FX Neutrik NC 5 MX Neutrik NC 5 FX Neutrik NC 4 FC plug jack 6,3 Mono plug jack 6,3 Stereo
. 392003. 392004. 392005. 392006
Adapter plug XLR 3pol male mono Adapter plug XLR 3pol female stereo Adapter plug XLR 3pol male to jack 6,3mm mono Adapter plug XLR 3pol female to jack 6,3mm mono
. 392007 XLR male / XLR male / adapter for extend. 392008 XLR female / XLR female / adapter for extend
. 392009 XLR female / RCA Chinch / adapter. 392010 XLR male / RCA Chinch / adapter