Color 150/DMX

Introduction

American DJ

Thank you for purchasing the Color 150/DMX by American DJ. Every Color 150/DMX has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your unit for any damage and be sure all equipment necessary to operate the system has arrived intact. In the event damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Please do not return the unit to your dealer without rst contacting customer support.

Customer Support

Customer Support:
American DJ provides a toll free customer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at www.americandj.com for any comments or suggestions. For service related issue please contact American DJ. Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacic Standard Time. Voice: (800) 322-6337 Fax: (323) 582-2610 E-mail: support@americandj.com not expose this unit to rain or moisture.
Warning! To prevent or reduce the risk of electrical shock or re, do
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact your nearest American DJ dealer.
PLEASE do not discard the shipping carton in the trash. Please recycle when ever possible.
4295 Charter Street Los Angeles Ca. 90058 www.americandj.com
Safety Issues: This unit may blow a fuse if the maximum allotted load of 5 amps is reached. If the fuse needs replacement, always replace the fuse with same exact type that was remove, unless otherwise instructed by an authorized American DJ service technician. Use of a different type fuse from that which is recommended may cause fire or electric shock and will void the manufactures warranty.

American

DJ Supply - www.americandj.com - Color 150/DMX Instruction Manual Page 2
Color 150/DMX Please carefully read and understand the instructions in this manual thoroughly before attempting to operate this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future reference. Color 150/DMX Be sure that the local power outlet match that of the required voltage for your unit. Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and re in case of an internal short. Disconnect from main power before making any type of connection. Do not remove the cover under any conditions. There are no user serviceable parts inside. Never plug this unit in to a dimmer pack Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6 (15cm) between this device and a wall. Never operate this unit when its cover is removed. To reduce the risk of electrical shock or re, do not expose this unit rain or moisture This unit is intended for indoor use only, use of this product outdoors voids all warranties. During long periods of non-use, disconnect the units main power. Always mount this unit in safe and stable matter. Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the fixture. Cleaning -The fixture should be cleaned only as recommended by the manufacturer. The fixture should be serviced by qualified service personnel when: A. The power cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the appliance. C. The appliance has been exposed to rain or water. D. The fixture does not appear to operate normally or exhibits a marked change in performance.

DJ Supply - www.americandj.com - Color 150/DMX Instruction Manual Page 3

General Instructions

Quick Start

Precautions

Master/Slave Quick Start Instructions Connect up to 16 units together via XLR cables. Follow the dip switch chart on page 11 for master/slave settings. The master unit will run the slaves to programs built-in to the master unit via an internal microphone. Plug in all units. When the Color 150/DMX is first turned on, it will run through an internal self test where it resets to their zero position. After the self test the units will react to sound, and chase to the built in programs. Color 150/DMX

Features

The Color 150/DMX features a bright 150 watt halogen lamp with a 500 hour life. The color wheel features seven brilliant colors plus white. The fixture includes a built-in microphone with adjustable sensitivity, this allows the fixture to automatically run to sound without the need of an external controller. The Color 150/DMX may also be set-up to run in a Master-Slave mode when used in multiples, up to 16 units. When used in the Master-Slave mode, the unit will chase to several internal programs. The Color 150/DMX can also be controlled via a standard DMX controller such as the American DJ Show Designer, or the American DJ DMX Operator, giving the user independent control over the color wheel. The units may also be set to run in to audio in DMX mode.
ZB-JCR/H5 15V/150W, 500Hr Lamp. DMX-512 Compatible. Stepper motor for smooth color change. 7 colors plus white. Master/Slave Operation. Sound Active. Sleep mode Optional MINI/C controller, for blackout control. Color 150/DMX

Halogen Lamp Warning

This fixture is fitted with a halogen lamp which is highly susceptible to damage if improperly handled. Never touch the lamp with your bare fingers as the oil from your hands will shorten lamp life. Also, never move the fixture until the lamp has had ample time to cool. Remember, lamps are not covered under warranty conditions.
DJ Supply - www.americandj.com - Color 150/DMX Instruction Manual Page 4
Color 150/DMX Color 150/DMX

Set Up

Power Supply:
Before plugging your unit in be sure the source voltage in your area matches the required voltage for your American DJ Color 150/DMX. The American DJ Color 150/DMX is available in a 120v and 220v version. Because line voltage may vary from venue to venue, you should be sure to plug your unit into a matching wall outlet before attempting to operate you xture.
Data Cable (DMX Cable) Requirements (For DMX Operation Only and Master-Slave): The Color 150/DMX can be controlled via DMX-512 protocol. The American DJ Color 150/DMX is a single channel DMX unit. The DMX address is set on the rear panel of the Color 150/DMX. Your unit and your DMX con troller require a standard 3-pin XLR connector for data input and data output (Figure 1). If you are making your own cables, be sure to use standard two conductor shielded cable (This cable may be purchased at almost all pro sound and lighting stores). Your cables should be made with a male and female XLR connector on either end of the Figure 1 cable. Also remember that DMX cable must be daisy chained and can not be split. Notice: Be sure to follow gure three when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cables shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs outer casing. Grounding the shield could cause a short circuit and erratic behavior.

XLR Male Socket 1 Ground 2 Cold 2 Cold XLR Female Socket 1 Ground
Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.
Termination reduces signal errors and avoids signal transmission problems and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture.

Figure 4

DMX Addressing
DMX is short for Digital Multiplex. This is a universal DMX binary language used as a form of communication between intelligent fixtures. Each dip switch represents a binary value. Dip Switch 1 address equals 1 Dip Switch 2 address equals 2 Dip Switch 3 address equals 4 Dip Switch 4 address equals 8 Dip Switch 5 address equals 16 Dip Switch 6 address equals 32 Dip Switch 7 address equals 64 Dip Switch 8 address equals 128 Dip Switch 9 address equals 256

DMX CHANNEL 32 128

XLR Pin Conguration
Pin 1 = Ground Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
Each dip switch has a preset value, a desired DMX address is set by combining the dip switches that will create your desired value. For example: To achieve a DMX address of 21, combine dip switches 1, 3, and 5. Sense dip switch 1 has a value of 1, dip switch 3 has a value of 4, and dip switch 5 has a value of 16, the combination of the create a DMX value of 21. Set DMX address 21: Dip switches # 1 = 1 3== 16 = 21

COMMON

Figure 2

DMX512 OUT 3-PIN XLR

DMX512 IN 3-PIN XLR

Figure 3

Set DMX address 201: Dip switches # 1 = 1 4== = 128 = 201
DJ Supply - www.americandj.com - Color 150/DMX Instruction Manual Page 5

DJ Supply - www.americandj.com - Color 150/DMX Instruction Manual Page 6

Operating Instructions

Operating Modes:
You can use the Color 150/DMX in three ways: Stand-Alone mode - The unit will react to sound, chasing through the several built in programs. You can also use the optional MINI/C remote control to blackout the units. Master/Slave mode - Allows you to daisy chain up to 16 fixtures together for a synchronized light show. The fixtures will react to sound chasing through several built in programs. DMX control mode - This function will allow you to control each fixtures DMX traits with a standard DMX 512 controller such as the American DJ Show Designer or DMX Operator. NOTE: Stand-Alone and Master/Slave operation require a sound source to operate properly. The units will blackout to conserve lamp life when inactive for more than 60 seconds. A single sound source will reactivate the units. For best results use fog or special effects smoke to enhance the beams projections.
4. Turn all the master units dip switches to the off position and follow the chart on page 11 for all slave dip switch settings. Note only one fixture may use the master units dip switch settings. 5. After all the units settings have been set and are plugged in, adjust the sensitivity knob on the bottom of the master unit to make them react to sound. 6. You can also use the optional MINI/C Remote Control. If you want to use the optional remote control, connect the MINI/C controller to the first fixture in the line (master).
Note: The remote control only operates in Stand-Alone and Master/Slave modes. If the remote is connected in DMX mode it will not function. If the units do not receive an active DMX signal, the units will automatically react to sound in the Master/Slave mode.

Stand Alone Mode:

1. To operate as a stand alone unit, via its internal chases and microphone, turn all dip switches off (see Page 11). 2. Adjust the sensitivity knob on the bottom of the unit so the unit will react to sound. Turning the sensitivity knob in a clockwise direction will make the fixture more sensitive to sound, turning the sensitivity knob in counter-clockwise direction will make the fixture less sensitive to sound.

Master-Slave Operation:

1. In Master-Slave operation one unit will act as the controlling unit and the others will react to the controlling units signal. Any unit can act as a Master or as a Slave. 2. Daisy chain your fixtures via the XLR connectors on the rear of the fixtures with standard XLR microphone cables. Remember that the Male XLR connector is the input and the Female XLR connector is the output. 3. The first unit in the chain (master) will only use the female XLR connector. The last unit in the chain will only use the male XLR connector.

DMX Mode: The Color 150/DMX is completely DMX-512 compatible. DMX allows a programmer the ability to create custom programs when using any universal DMX controller such as the American DJ Show Designer or the American DJ DMX Operator. 1. To operate your fixtures in DMX mode please follow the DMX set-up procedures beginning on page 5. 2. After all the proper set-up procedures have been completed, follow the standard DMX binary code on page 6 to assign a unique DMX address to each individual fixture. A dip switch chart has been included in this manual on page 12. Please note the dip switch guide on page 12 is set up as a guide only. Please follow the instructions included with your DMX controller for proper DMX addressing. 3. The fixture uses one DMX channel to operate in DMX mode, this channel control color change. 4. For further information on operating in DMX mode please refer to your controllers owners manual.
DJ Supply - www.americandj.com - Color 150/DMX Instruction Manual Page 7
DJ Supply - www.americandj.com - Color 150/DMX Instruction Manual Page 8
Color 150/DMX The MINI/C controller may be purchased separately allowing you to control the main unit, and any others connected to it, while it is in stand alone mode. You can set the unit to blackout. If you have more than one unit, make sure the remote control is plugged into the first unit in the daisy chain. The remote control will not have any effect if the unit is in DMX mode. When the unit is in blackout mode, the light will come on next to the blackout button. The Color 150/DMX may be controlled by a wide range of controllers; ie. Show Designer, DMX Operator, Scene Setter or by the MINI/C basic controller.

Optional MINI/C Remote

Cleaning
Due to fog residue, smoke, and dust, cleaning the internal and external optical lenses must be carried out periodically to optimize light output. 1. Use normal glass cleaner and a soft cloth to wipe down the outside casing. 2. Use a brush to wipe down the fan grill. 3. Clean the external optics with glass cleaner and a soft cloth every 20 days. Situation may very. If used heavily in clubs with lots of fog, cleaning may be required more often. 4. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days. 5. Always be sure to dry all parts completely before plugging the unit in.

MINI/C features: 30 ft. cable
Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue, dust, dew). Color 150/DMX

DMX Traits

The fixture has been designed with a special Sound-Active DMX feature. When using this fixture with a DMX controller, you may activate the Sound-Active mode. This feature may prove useful when exact color combinations are not important or there is not enough time to program a complete show.
DMX Value: 0-25 26-51 52-77 78-103 104-129 130-155 156-181 182-207 208-233 234-255 = = = = = = = = = =

Trait:

Stand by (Black out)
Lamp Off White Red Blue Green Yellow Orange Pink Magenta Sound-Active Function
DJ Supply - www.americandj.com - Color 150/DMX Instruction Manual Page 9
DJ Supply - www.americandj.com - Color 150/DMX Instruction Manual Page 10
Color 150/DMX The following details the proper dip switch setting for Master-Slave operation. Please follow these setting when running four units in a Master-Slave conguration.

ON ON ON

Master/Slave Settings

DMX Settings

This chart details DMX dip switch setting for the first 16 units (beginning on DMX address one). This chart is designed as a guide only. Please follow standard binary DMX protocol as described on page 6 for proper dip switch settings beyond the sixteenth unit or for units not starting at DMX channel one. For the American DJ DMX Operator setting please refer to the DMX Operator manual.
Master - Head 1 Head 2 Head 3

Head 1

Head 2

Head 3

Head 4

Head 5 Head 6

Head 5

Head 6

Head 7

Head 8

Head 9

Head 10

Head 11

Head 12

9 ON ON ON

Head 13

Head 14

Head 15

Head 16
DJ Supply - www.americandj.com - Color 150/DMX Instruction Manual Page 11
DJ Supply - www.americandj.com - Color 150/DMX Instruction Manual Page 12
Color 150/DMX The Color 150/DMX carries a one year (365 days) limited warranty. We recommend you fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Please contact American DJ customer support for a R.A. number. Color 150/DMX Fuse & Lamp Replacement

Warranty Registration

Trouble Shooting
Listed below are a few common problems users may encounter, with solutions. Note: The unit has been designed to shut the lamp down after 60 seconds of inactivity. This is a way of extending lamp life, be assured this is not a problem with the fixture. If problems are not resolved; Contact American DJ customer support for possible service options.

Caution: Always replace with the exact same type lamp and fuse, unless otherwise specified by an authorized American DJ technician. Replace with anything other than the specified part can damage your unit and will void your manufactures warranty. Warning: If after you have replaced the lamp or fuse and you continue to blow either one, STOP using the unit. Contact customer support for further instructions, you may have to return the unit for servicing. Continuing to use the unit may cause serious damage. Fuse Replacement:
Disconnect the units main power supply. Insert a standard flat head screw driver in to the fuse holder housing. Turn the screwdriver in counter-clockwise direction to remove the fuse holder. Remove the old fuse and discard it, replace the fuse with the same type. Insert the fuse holder back into its housing and turn in clockwise direction to lock the holder in place.
No light from the unit; 1. Be sure the Power On (red) LED is lit and the fan is running. If not, there is no main power supply. 2. Be sure the fuse located on the rear panel is good. 3. If power is present but the lamp does not light, the lamp may need to be replaced.

Lamp Replacement:

Caution! Never open the unit while in use. Always disconnect the main power before attempting to replace the lamps. Allow the unit ample time to cool before replacing lamps 1. Be sure to follow the proper procedures when handling halogen bulbs. Never touch the lamp with your bare fingers. 2. Locate the thumb screws that retaining the lamp cover to the fixture. Unscrew the retaining thumb screws to expose the lamp socket assemble. 3. Gently remove and discard the old lamp. 4. Insert the new lamp in the lamp/socket assembly and reassemble.
Unit not responding to DMX; 1. If the Green LED on the top of the unit is flashing, the unit is definitely receiving DMX. 2. Check the dip switch settings. 3. If the DMX LED is not lit, be sure the DMX cables are connected properly and are wired correctly (pin 3 is hot; on some other DMX devices pin 2 may be hot). Also, check that all cables are connected to the right connectors; it does matter which way the inputs and outputs are connected. 4. If it is a bad connection, the Green LED may flash when cables are wiggled (but remember it may also be the unit sensing audio!). 5. If DMX connectors are fairly short, ordinary microphone cables may be used. For longer runs, this may cause data transmission problems (which will show up as random or incorrect movements) for best result, use proper balanced data transmission cable. 6. If your DMX controller has a polarity switch, be sure the switch is in the set to the proper position. 7. If the unit was in DMX Sound-Active mode, the unit must hear a beat to return to regular DMX mode.

Unit does not respond to sound; 1. Be sure the unit is not in DMX mode (green LED off). 2. Tapping on the microphone, quiet or high pitched sounds may not activate the unit. 3. Be sure the audio sensitivity knob is turn in the full clockwise position (maximum sensitivity).
DJ Supply - www.americandj.com - Color 150/DMX Instruction Manual Page 13
DJ Supply - www.americandj.com - Color 150/DMX Instruction Manual Page 14

1-YEAR LIMITED WARRANTY

A. American DJ hereby warrants, to the original purchaser, American DJ products to be free of manufacturing defects in material and workmanship for a period of 1 year (365 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owners responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought. B. For warranty service, send the product only to the American DJ factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, American DJ will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be shipped with the product. If any accessories are shipped with the product, American DJ shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof. C. This warranty is void if the serial number has been altered or removed; if the product is modied in any manner which American DJ concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the American DJ factory unless prior written authorization was issued to purchaser by American DJ; if the product is damaged because not properly maintained as set forth in the instruction manual. D. This is not a service contract, and this warranty does not include maintenance, cleaning or periodic check-up. During the period specied above, American DJ will replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of American DJ under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of American DJ. All products covered by this warranty were manufactured after January 1, 1990, and bear identifying marks to that effect. E. American DJ reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by American DJ in connection with this product, including warranties of merchantability or tness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or tness, shall apply to this product after said period has expired. The consumers and or Dealers sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall American DJ be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product. G. This warranty is the only written warranty applicable to American DJ Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published. H. Lamps are not covered under this warranty

Technical Specifications:

Model: Color 150/DMX

Lamp: Voltage: Dimensions: Colors Weight: Fuse: Duty Cycle: Sound Active: Cooling: DMX 512: Working Position: Warranty:
15v/150w JCR/HHour 120v~60Hz 8.3 x 8.8 x 5.Color plus White 7.5 Lbs 5 Amp AGC Several Hours Yes Fan Cooled Yes Any Safe position 1 Year (365 days)
Please Note: Specications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
DJ Supply - www.americandj.com - Color 150/DMX Instruction Manual Page 15
American DJ Supply American DJ Group of Companies World Headquarters: 4295 Charter Street Los Angeles, CA 90058 USA Tel: 323-582-2650 / Fax: 323-582-2610 Web: www.americandj.com / E-mail: info@americandj.com

Sunray Tri LED DMX

General Information
Unpacking: Thank you for purchasing the Sunray Tri LED DMX
by American DJ. Every Sunray Tri LED DMX has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact. In the event damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Do not return this unit to your dealer without first contacting customer support.
Introduction: The Sunray Tri LED DMX is part of American DJs
continuing pursuit for creating and upgrading affordable intelligent fixtures The Sunray Tri LED DMX is an colorfull upgrade to our Sunray LED DMX. The Sunray Tri LED DMX is an DMX intelligent centerpiece. This fixture can be used as a stand alone piece or connected in a Master/Slave configuration. The unit can sound active, run in a auto mode or be controlled via DMX controller. When used in DMX mode the fixture uses 3 DMX channels.
Customer Support: American DJ provides a toll free customer sup-
port line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at www.americandj.com for any comments or suggestions. Service Hours are Monday through Friday 9:00 a.m. to 4:30 p.m. Pacific Standard Time. Voice: (800) 322-6337 Fax: (323) 582-2941 E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com

User Instructions

Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact American DJ.

Rev. 12/10

American
DJ - www.americandj.com - Sunray Tri LED DMX Instruction Manual Page 2

General Instructions

Safety Precautions
Please carefully read and understand the instructions in this manual thoroughly before attempting to operate this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future reference. Sunray Tri LED DMX Product Registration The Sunray Tri LED DMX carries a 3 year (1095 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Please contact American DJ customer support for a R.A. number. Sunray Tri LED DMX Main Features Bright 3 Watt LED Produces 34 Colors, using Green, Purple, Blue, Yellow, & Orange DMX-512 Compatible Master/Slave Operation 3 DMX Channels Optional UC3 Controller Compatible (Not Included)
o reduce the risk of electrical shock or fire, do not expose this unit T rain or moisture o not spill water or other liquids into or on to your unit. D e sure that the local power outlet match that of the required volt- B age for your unit. o not attempt to operate this unit if the power cord has been D frayed or broken. o not attempt to remove or break off the ground prong from the D electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short. isconnect from main power before making any type of connection. D o not remove the cover under any conditions. There are no user D serviceable parts inside. ever operate this unit when its cover is removed. N ever plug this unit in to a dimmer pack N lways be sure to mount this unit in an area that will allow proper A ventilation. Allow about 6 (15cm) between this device and a wall. o not attempt to operate this unit, if it becomes damaged. D his unit is intended for indoor use only, use of this product out T doors voids all warranties. uring long periods of non-use, disconnect the units main power. D lways mount this unit in safe and stable matter. A ower-supply cords should be routed so that they are not likely to P walked on or pinched by items placed upon or against them, be paying particular attention to cords at plugs, convenience recep- tacles, and the point where they exit from the appliance. Cleaning -The fixture should be cleaned only as recommended by manufacturer. See page 10 for cleaning details. the eat -The appliance should be situated away from heat sources H such as radiators, heat registers, stoves, or other appliances (in cluding amplifiers) that produce heat. he fixture should be serviced by qualified service personnel when: T The power-supply cord or the plug has been damaged. A. Objects have fallen, or liquid has been spilled into the appliance. B. The appliance has been exposed to rain or water. C. The appliance does not appear to operate normally or exhibits a D. marked change in performance.

DJ - www.americandj.com - Sunray Tri LED DMX Instruction Manual Page 3
DJ - www.americandj.com - Sunray Tri LED DMX Instruction Manual Page 4

Sunray Tri LED DMX

Set Up
Sunray Tri LED DMX dipswitch 10 it is used for special functions.
Power Supply: Before plugging your unit in, be sure the source volt-
age in your area matches the required voltage for your American DJ Sunray Tri LED DMX. The American DJ Sunray Tri LED DMX is available in a 120v and 220v version. Because line voltage may vary from venue to venue, you should be sure your unit voltages matches the wall outlet voltage before attempting to operate you fixture.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures (most controllers only have a DATA OUT terminal). DMX Linking: DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain. Dip-switches in DMX mode: This unit uses dipswitches to assign a DMX address. Each dipswitch represents a binary value. Dipswitch 1 address equals 1 DMX CHANNEL Dipswitch 2 address equals 128 SP Dipswitch 3 address equals 4 Dipswitch 4 address equals 8 Dipswitch 5 address equals 16 Dipswitch 6 address equals 32 ON Dipswitch 7 address equals 64 Dipswitch 8 address equals Dipswitch 9 address equals 256 Dipswitch 10 - Some units omit dipswitch 10. When a unit does include
Each dipswitch has a preset value. A specific DMX address is set by combining the dipswitches that sum your desired value. For example: To achieve a DMX address of 21, combine dipswitches 1, 3, and 5. Sense dipswitch 1 has a value of 1, dipswitch 3 has a value of 4, and dipswitch 5 has a value of 16, the combination of the create a DMX value of 21. Set DMX address 21: Set DMX address 201: Dipswitch # 1 = 1 Dipswitch # 1 = 1 Dipswitch # 3 = 4 Dipswitch # 4 = 8 Dipswitch # 5 = 16 Dipswitch # 7 = 64 = 21 Dipswitch # 8 = 128 = 201
Data Cable (DMX Cable) Requirements (For DMX and Master/ Slave Operation): The Sunray Tri LED DMX can be controlled via

DMX-512 protocol. The American DJ Sunray Tri LED DMX is a three channel DMX unit. The DMX address is set below the dome of the Sunray Tri LED DMX. Your unit and your DMX controller require a standard 3-pin XLR connector for data input and data output (Figure 1). If you are making your own cables, be sure to use standard two conductor shielded cable (This cable may be purchased at almost all pro sound and lighting stores). Your cables should be made with a male and female XLR connector on either end of the Figure 1 cable. Also remember that DMX cable must be daisy chained and can not be split.
REMOTE CONTROL INPUT INPUT OUTPUT SOUND REMOTE CONTROL INPUT INPUT OUTPUT
DMX512 Notice: Be sure to follow figures two and three when making your own DMX+,DMX-,COMMON
cables. Do not use the ground lug on the XLR connector. Do not connect the cables shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs outer casing. Grounding the shield could cause a short circuit and erratic behavior.
COMMON DMX512 OUT 3-PIN XLR

DMX + DMX -

DMX512 IN 3-PIN XLR

Figure 2

Termination reduce avoids signal trans and interference. It to connect a DMX te 120 Ohm 1/4 W) bet and PIN 3 (DMX +)
DJ - www.americandj.com - Sunray Tri LED DMX Instruction Manual Page 5
DJ - www.americandj.com - Sunray Tri LED DMX Instruction Manual Page 6

XLR Male Socket 1 Ground

SOUND REMOTE CONTROL INPUT

XLR Pin Configuration

Pin 1 = Ground Pin 2 INPUT = Data Compliment (negative)
REMOTE CONTROL INPUT OUTPUT

XLR Female Socket 2 Cold

Operating Modes:

Operation

2 Cold

INPUT OUTPUT

1 Ground
Stand-Alone Operation (Sound Active and Auto Program):
Pin 3 = Data True (positive)

Figure 3

Special Note: Line Termination. When longer runs of cable are

POWER POWER

used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number ZDMX/T) will decrease the possibilities of erratic behavior.
Sound Active: 1. Put dipswitch #1 in the On position. The unit will react to the low frequencies of music via the microphone. Auto Program: 1. To run the Auto Program, put dipswitches 1 & 2 in the On po sition. Dipswitch 3 will reverse the rotation. Dipswitches 4, 5, & 6 will control the speed of rotation. 2. The optional UC3 Controller (not included) may be used to con- trol different functions including blackout. See the next page for UC3 controls.

Master-Slave Operation:

Termination reduces signal errors and avoids signal transmission problems and interference. It is always advisable to connect a DMX terminal, (Resistance 120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last fixture.

Figure 4

5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR
connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion Conductor
Ground/Shield Data Compliment (- signal) Data True (+ signal) Not Used Not Used

3-Pin XLR Female (Out)

Pin 1 Pin 2 Pin 3

5-Pin XLR Male (In)

Pin 1 Pin 2 Pin 3 Do Not Use Do Not Use
This function will allows you to link units together to run in a MasterSlave mode. In Master-Slave operation one unit will act as the controlling unit and the others will react to the controlling units built-in programs. Any unit can act as a Master or as a Slave however, only one unit can be programmed to act as the Master. 1. Using standard XLR microphone cables, daisy chain your units together via the XLR connector on the rear of the units. Remem- ber the Male XLR connector is the input and the Female XLR connector is the output. For longer cable runs we suggest a terminator at the last fixture. 2. Simply daisy chain the units together using XLR cables. 3. For the Master unit put dipswitch 1 in the On position, and all other dipswitches in the Off position. For the Slave units, put any dipswitch in the On position, except the #1 dipswitch. The #1 dispswitch must stay in the Off position on all Slave units. 3. The optional UC3 Controller (not included) may be used to con- trol different functions including blackout. See the next page for UC3 controls.
Universal DMX Control: This function allows you to use a universal DMX-512 controller such as the Elation DMX Operator or Show Designer. to control the DMX traits. Operating through a DMX
DJ - www.americandj.com - Sunray Tri LED DMX Instruction Manual Page 7
DJ - www.americandj.com - Sunray Tri LED DMX Instruction Manual Page 8
Stand by Function Mode Blackout the unit 1. Synchronous Strobe 2. Two light Strobe 3. Sound Strobe Strobe (LED OFF)

UC3 Control

controller gives freedom to create unique programs tailored to ones individual needs. 1. The Sunray Tri LED DMX uses 3 DMX channels. Channel 1 con- trols the dimmer/strobe, channel 2 controls color selection and channel 3 controls dome rotation. See the bottom of this page for the DMX traits. 2. To control your fixture in DMX mode, follow the set-up proce- dures on pages 5 - 7 as well as the set-up specifications that are included with your DMX controller. Using the dipswitches assign a DMX address to the unit. See page 7 for addressing. 3. For help operating in DMX operation consult the manual included with your DMX controller. 4. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.

Rotation Speed 1-8 Rotation (LED ON)

Fuse Replacement

Channel 1

Function

DMX Traits
Disconnect the units main power supply. Insert a standard flat head screw driver in to the fuse holder housing. Turn the screwdriver in counter-clockwise direction to remove the fuse holder. Remove the old fuse and discard it, replace the fuse with the same type. Insert the fuse holder back into its housing and turn in clockwise direction to lock the holder in place. Sunray Tri LED DMX Cleaning
DIMMER/STROBE 0-- - - 255 CLOSED DIMMER 0% - 100% STROBING FAST - SLOW OPEN COLOR SELECTION DOME ROTATION 0-- - - - 255 NO ROTATION CLOCKWISE FAST - SLOW NO ROTATION COUNTER-CLOCKWISE SLOW - FAST NO ROTATION
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the

0 - 255

internal and external optical lenses and mirror should be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates (I.e. smoke, fog residue, dust, dew). In heavy club use we recommend cleaning on a monthly basis. Periodic cleaning will ensure longevity, and crisp output. 1. Use normal glass cleaner and a soft cloth to wipe down the out- side casing. 2. Use a brush to wipe down the cooling vents and fan grill. 3. lean the external optics with glass cleaner and a soft cloth every C 20 days. 4. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days. 5. Always be sure to dry all parts completely before plugging the unit back in.
DJ - www.americandj.com - Sunray Tri LED DMX Instruction Manual Page 9
DJ - www.americandj.com - Sunray Tri LED DMX Instruction Manual Page 10

Warranty

Technical Specifications:
LEDs: Colors: Voltage: Dimensions: Weight: Power Consumption: Fuse: Duty Cycle: DMX: Working Position: Warranty:
MANUFACTURERS LIMITED WARRANTY A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American Audio products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owners responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought. B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, American DJ, Inc. will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be shipped with the product. If any accessories are shipped with the product, American DJ, Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof. C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the American DJ, Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the product is damaged because not properly maintained as set forth in the instruction manual. D. This is not a service contract, and this warranty does not include maintenance, cleaning or periodic check-up. During the period specified above, American DJ, Inc. will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of American DJ. All products covered by this warranty were manufactured after January 1, 1990, and bear identifying marks to that effect. E. American DJ, Inc. reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by American DJ, Inc. in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumers and/or Dealers sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall American DJ, Inc. be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product. This warranty is the only written warranty applicable to American DJ and American Audio Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published. MANUFACTURERS LIMITED WARRANTY PERIODS: All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Amplifiers) All American Audio V-Plus Series Amplifiers = 3-year (1095 day) Limited Warranty American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty (Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps, and Star Tec Series) American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors which have a 1-year (365 day Limited Warranty) American DJ - www.americandj.com - Sunray Tri LED DMX Instruction Manual Page 11

Model:

One 3 Watt RGB 100v~240v/ 50~60Hz 8.25 (L) x 8.25 (W) x 7 (H) 210mm x 210mm x 179mm 4 Lbs. / 1.8 Kgs 13W 1 Amp GMA None 3 Channels Any Safe, Secure Position 3 Year (1095 days)
Please Note: Specifications and improvements in the design
of this unit and this manual are subject to change without any prior written notice.
American DJ Supply American DJ World Headquarters: 6122 S. Eastern Ave. Los Angeles, CA 90040 USA Tel: 323-582-2650 / Fax: 323-582-2610 Web: www.americandj.com / E-mail: info@americandj.com American DJ Europe Junostraat EW Kerkrade Netherlands service@americandj.eu / www.americandj.eu Tel: +00 / Fax: +99