User Manual

Antari Z Series Fog Machine
Congratulations on the purchase of your new ANTARI Z Series FOG MACHINE.

Introduction

Thank you for choosing an ANTARI Fog Machine. You now own a rugged and powerful tate-of-the-art machine. Prior to use, we suggest that you carefully read all of the instructions. By following the suggestions found in this user manual, you can look forward to the reliable and satisfactory performance of your ANTARI Fog Machine for years to come.
Please follow these operation, safety and maintenance instructions to ensure a long and safe life for your fog machine. Cautions Risk of electric shock. Disconnect the appliance from the electric supply before removing the cover. Note: there are no user serviceable parts inside. Danger of electric shock Keep this device dry. For inside use only. Not designed for outside use. For the 110V models, use 3-prong grounded electrical outlet only. Prior to use take care to determine that the unit is installed at the rated voltage. Always unplug your ANTARI Fog Machine before filling its tank. Keep fog machine upright. Turn off or unplug when not in use. This machine is not water- or splash-proof. If moisture, water, or fog liquid gets inside the housing, immediately unplug the unit and contact a service technician or your ANTARI dealer before using it again. No user serviceable parts inside. Refer to your ANTARI dealer or other qualified service personnel. Danger of burns For adult use only. Fog machine must be installed out of the reach of children. Never leave the unit running unattended. Never aim the output nozzle directly at people.
Fog machine output is very hot. Avoid coming within 60 cm of the output nozzle during operation. Locate the fog machine in a well-ventilated area. Never cover the units vents. In order to guarantee adequate ventilation, allow a free air space of at least 20 cm around the sides and top of the unit. Never aim the output nozzle at open flames. If the supply cord is damaged, it must be replaced by manufacturer or its service agent or similarly qualified person in order to avoid a hazard. The output nozzle becomes very hot during operation (300C). Keep flammable materials at least 50 cm away from the nozzle. Always allow your ANTARI Fog Machine to cool down before attempting to clean or service it.
Danger of explosion Never add flammable liquids of any kind (oil, gas, perfume) to the fog liquid. Pay attention to all warning labels and instructions printed on the exterior of your ANTARI Fog Machine Use only the high-quality, water-based fog liquid that your dealer recommends. Other fog liquids may cause clogging or spitting. Always make sure there is sufficient liquid in the fog liquid tank. Operating this unit without liquid will cause damage to the pump as well as over-heating of the heater. If your ANTARI Fog Machine fails to work properly, discontinue use immediately. Drain all fog liquid from the tank, pack the unit securely (preferably in the original packing material), and return it to your ANTARI dealer for service. Always drain tank before mailing or transporting this unit. Never drink fog liquid. If it is ingested, call a doctor immediately. If fog liquid comes in contact with skin or eyes, rinse thoroughly with water. Unpacking & Inspection Open the shipping carton and verify that all equipment necessary to operate the system has arrived intact. Refer to the Features section for information on what items are included with your model. If any equipment is missing contact your ANTARI dealer immediately. Before beginning initial setup of your ANTARI Fog Machine, make sure that there is no evident damage caused by transportation. In the event that the units housing or cable is damaged, do not plug it in and do not attempt to use it until after contacting your ANTARI dealer for assistance. Setup Remove all packing materials from shipping box. Check that all foam and plastic padding is removed, especially in the nozzle area. Place fog machine on a flat surface and remove fog liquid tank cap. Fill with ANTARI Fog Liquid or other high-quality water-based fog fluid. Any other types of fluid can damage the unit. When filled, place cap back on liquid tank. Firmly attach the remote control cable to the proper input on the rear of the machine.

Operation Plug power cord into a grounded electrical outlet. If necessary, turn power switch on rear of unit to ON position. Warm-up is complete when green lamp lights up on remote unit. To emit fog, press the appropriate button on the remote for the desired length of time. The remote units lamp will cycle on and off as the machine re-heats to the proper operating temperature. For further information on operating your ANTARI Fog Machine, see the section titled, Remote Control Operation. If your model includes a mounting bracket designed for overhead installation, it may be installed at floor level or suspended overhead. If the unit is to be mounted using the bracket, it is important that the fog does not shoot directly at any ones face. Whatever installation method you choose, do not allow the unit to have more than a 15 degree angle of inclination. Important: Always monitor tank fluid level as you are fogging. Running a fog machine with no fluid can permanently damage the unit. If you experience low output, pump noise or no output at all, unplug immediately. Check fluid level, the external fuse, remote connection, and power from the wall. If all of the above appears to be O.K., plug the unit in again. If fog does not come out after holding the remote button down for 30 seconds, check the hose attached to the tank to make sure there is fluid going through the hose. If you are unable to determine the cause of the problem, do not simply continue pushing the remote button, as this may damage the unit. Return the machine to your ANTARI dealer. Remote Control Operation Z-1: 10 meter wired remote controller with five-prong plug for ANTARI Fog Machine models Z-800 and Z-1000. The red lamp indicates that the unit is receiving power. When the fog machine has reached operating temperature the green lamp on this remote control will light up, indicating that the operator may begin fog emission by pressing the red button. The green lamp turns off during fog machine warm-up (approx. 4 minutes) and re-heating cycles (approx. 1-2 minutes), and turns on when the machine becomes operational. Z-2: 10 meter wired multi-function remote controller with 5-pin XLR connector for ANTARI Fog Machine models Z-1500 and Z-3000. Its interface allows the operator to customize fog machine functions by adjusting fogging duration, interval and volume. Its LCD displays current operating parameters, which are automatically stored in non-volatile memory, allowing the machine to be powered down without losing function settings. Instructions below: Description of the elements of the Z-2: (1) LCD-Display (2) Function-key (3) Up-/Down-keys (4) Timer-key (5) Volume-switch (6) Manual-key 3

1. Via the Function key, you can adjust the desired settings. After pressing the Function key once, the display shows "Interval Set". Adjust the interval between each fog emission (within the range of 1 to 255 seconds) by means of the Up-/Down keys. By pressing the Function-key twice, the display shows "Duration Set". Adjust the duration of each fog emission (within the range of 1 to 20 seconds) by means of the Up/Down keys. Under the menus "Timer Out" and "Volume Out" you can adjust the output volume by means of the Up/Down keys. The menu "DMX Add" refers to adjusting the DMX address for DMX control or synchronization. Adjust the desired DMX-address by means of the Up/Down keys. 2. Press the Timer key to activate the timer function. The display shows the adjusted interval and the device counts the seconds down to "0". After that, the fog emission is triggered at the volume adjusted under "Timer Out". The duration depends on the settings adjusted under "Duration Set". If you wish to deactivate the timer function, press the Timer key once more. 3. Press the Volume switch for immediate triggering of the fog emission at the volume adjusted under "Volume Out". Press the Volume switch once more in order to stop the fog emission. 4. Press the Manual key for immediate triggering of the fog emission at 100 % volume. Let the Manual key loose in order to stop the fog emission. For control of the DMX settings please refer to the section on Page 6 titled Antari Z-Series Onboard DMX Fog Machine Settings
Z-4: 10 meter wired remote controller with five-prong plug for ANTARI Fog Machine
models Z-800 and Z-1000. To use the Z-4 remote control, press the red POWER button to enable the remotes functions. The two knobs allow the operator to customize fog machine operation by adjusting output duration and interval. Press the yellow TIMER button to activate the timer function. Adjust the interval between each fog emission (within the range of 10 seconds to 5 minutes) by means of the INTERVAL control knob. Adjust the duration of each fog emission (within the range of 1 to 10 seconds) by means of the DURATION control knob. When pressed, the green FOG button overrides all other function controls, and activates maximum output.
Z-5: Wireless remote controller with five-prong plug for ANTARI Fog Machine models Z800 and Z-1000. Remote operation is possible up to a distance of 50 meters. Z-8: 10 meter wired timer and volume remote control for the Z-1200 ANTARI Fog Machine. To engage the timer function presses the yellow button on the handheld unit. The duration knob regulates the length of time of the smoke blast. The blast can be set for between 1 and 15 seconds. The interval knob controls the amount of time between blasts. This can be set between 10 and 255 seconds. For continuous fogging, depress the red button marked Continuous. This will set the unit to fog steadily at the selected volume. The volume of fog produced is regulated via the output knob. This varies between 0 and 100% of maximum volume output. The green Manual button overrides any timer and/or volume settings to deliver a full volume blast of fog for as long as the button is held down. 4

Cleaning your fog machine regularly will help reduce costly parts replacement and repair charges.
Maintenance Do not allow the fog liquid to become contaminated. Always replace the caps on the fog liquid container and the fog machine liquid tank immediately after filling. After every 40 hours of continuous operation, it is recommended to run a cleaning solution composed of 80% distilled water/20% white vinegar through the system to prevent the accumulation of particulate matter in the heating element. The recommended cleaning regimen is as follows: 1. While unit is unplugged and cool, unscrew nozzle at very front of unit and clean out debris with vinegar and a pipe cleaner, making sure that the hole is free of clogs. 2. Empty all fog fluid from machine. Add cleaning solution to tank. Plug unit in and begin warm up. 3. Run unit in a well-ventilated area until tank is empty. 4. Replace nozzle. 5. Cleaning is now complete. Refill with fog liquid. Note: All fog machines are prone to clogging due to the thick consistency of fog fluid and the high temperature at which it vaporizes. However, a properly maintained fog machine should provide years of reliable use. Clean with a dry cloth only. Store dry. Performance Notes All fog machines develop condensation around the output nozzle. Because this may result in some moisture accumulation on the surface below the output nozzle, consider this condensation when installing your unit. All fog machines may sputter small amounts of fog occasionally during operation and for a minute or so after being turned off. All fog machines have a recycling period after long bursts when the machine will shut itself down for a short period in order to heat back up. During this time no fog can be produced. The green READY L.E.D. on the remote will be off during this time and will light up again when the machine is ready. If the supply cord is damaged, it must be replaced by manufacturer or its service agent or similarly qualified person in order to avoid a hazard.
Please read and save these instructions
Antari Z-Series Onboard DMX Fog Machine Settings
DMX Setting for Z-series fog machines with onboard DMX

Channel A 250-255

6 - 249
0 - 5 = OFF = Volume Control ( 5% - 95%)
= Maximum Volume Output ( 100%)
The Z-1200, Z-1500 and Z-3000 fog machines all have onboard DMX control. Currently all three models use 1 channel to control volume output operation. Each channel has a value range of 0 to 225. Timer functions such as duration and interval can be programmed using the DMX controller or the DMX control software being used by lighting and effects operator. If Channel A has a value from 0 to 5, the unit is OFF. Between the values 6 to 249 the volume of fog output is regulated. With 6 being the minimum volume of fog produced and 249 approaching the maximum. The volume output rises as the DMX value is increased. If Channel A has a value from 250 TO 255, the machine will operate at maximum output. Note: In the example above, if the machine were assigned the DMX address of 124, Channel A would correspond to DMX address 124. In general, Antari fog machines with onboard DMX conform to the following performance specifications: 1. Average Operating temperature = 250C 2. Fogger can maintain maximum output for 30 seconds or more 3. Fogger can maintain constant output at 30% volume setting (roughly a value of 75).

Z-1200II USER MANUAL Z-1200II BEDIENUNGSANLEITUNG Mode DEmploi des Z-1200II Machines Fume
Congratulations on the purchase of your new ANTARI Z-SERIES II FOG MACHINE. Wir beglckwnschen Sie zum Kauf Ihres neuen ANTARI Z-SERIES NEBELGERTES. Nous vous flicitons pour lachat de votre nouvelle Z-SERIES machine fume dANTARI.
Read and save these instructions Bitte lesen Sie diese Anweisungen und bewahren Sie sie gut auf Lisez et Gardez ces instructions 2005 Antari Lighting and Effects Ltd.

User Manual

Antari Z 1200II Fog Machine
Congratulations on the purchase of your new ANTARI Z-Series II FOG MACHINE.

Introduction

Thank you for choosing ANTARI Z-Series II Fog Machine. You now own a rugged and powerful state-ofthe-art machine. Prior to use, we suggest that you carefully read all of the instructions. By following the suggestions found in this user manual, you can look forward to the reliable and satisfactory performance of your ANTARI Fog Machine for years to come. Please follow these operation, safety and maintenance instructions to ensure a long and safe life for your fog machine.

CAUTION:

Risk of electric shock. Disconnect the appliance from the electric supply before refilling liquid, cleaning or performing maintenance on the machine.
Danger of Electric Shock Keep this device dry. For inside use only. Not designed for outside use. For the 110V models, use 3-prong grounded electrical outlet only. Prior to use take care to determine that
the unit is installed at the rated voltage. Always unplug your ANTARI Z-Series II Fog Machine before filling its tank. Always keep fog machine in upright position. Turn off or unplug the machine when not in use. This machine is not water-proof. If moisture, water, or fog fluid gets inside the housing, immediately unplug the unit and contact a service technician or your ANTARI dealer before using it again. No user serviceable parts inside. Refer to your ANTARI dealer or other qualified service personnel.
Danger of Burns For adult use only and must be installed out of the reach of children. Never leave the unit running

unattended.

Never aim the output nozzle directly at people. Fog machine output is very hot. Avoid coming within 60 cm of the output nozzle during operation. Locate the fog machine in a well-ventilated area. Never cover the units vents. In order to guarantee
adequate ventilation, allow a free air space of at least 20 cm around the sides and top of the unit.
Never aim the output nozzle at open flames. If the supply cord is damaged, it must be replaced by manufacturer or its service agent or similarly qualified
personnel in order to avoid a hazard. away from the nozzle.
The output nozzle becomes very hot during operation (300C). Keep flammable materials at least 50 cm
Always allow your ANTARI Fog Machine to cool down before attempting to clean or service it. Danger of Explosion Never add flammable liquids of any kind (such as oil, gas, perfume) to the fog liquid. Use only high-quality, water-based fog liquid that your dealer recommends. Other fog liquids may cause

clogging or spitting.

Always make sure there is sufficient liquid in the tank. Operating this unit without liquid will cause damage

to the pump as well as over-heating of the heater.
If your ANTARI Z-1200II Fog Machine fails to work properly, discontinue use immediately. Drain all fog
liquid from the tank, pack the unit securely (preferably in the original packing material), and return it to your ANTARI dealer for service. Always drain tank before mailing or transporting this unit. Never drink fog liquid. If it is ingested, call a doctor immediately. If fog liquid comes in contact with skin or eyes, rinse thoroughly with water.
Note: Pay attention to all warning labels and instructions printed on the exterior of your ANTARI Fog Machine
Unpacking & Inspection
Open the shipping carton and verify that all equipment necessary to operate the system has arrived intact. The shipping carton should contain the following items: 1. 2. 3. 4. One unit of Z-1200II Fog Machine Power cord Z-8 multi-function remote control with attached cord User Manual
If any equipment is missing contact your ANTARI dealer immediately. Before beginning your initial setup on ANTARI Z-1200II Fog Machine, make sure that there is no evident damage caused by transportation. In the event that the units housing or cable is damaged, do not plug it in and do not attempt to use it until after contacting your ANTARI dealer for assistance.
Setup Remove all packing materials from shipping box. Check that all foam and plastic padding is removed,
especially in the nozzle area.
Place fog machine on a flat surface and remove fog liquid tank cap. Fill with ANTARI fog liquid or other high-quality water-based fog fluid recommended by ANTARI dealer.
Any other types of fluid can damage the unit resulting in spitting and serious clogging problem. When filled, place cap back on liquid tank. Be careful not to exceed the maximum fluid level. DO NOT OVERFILL. Firmly attach the Z-8 remote control cable to the proper input on the back of the machine.
Operation Add fluid carefully to the liquid tank. Do not overfill the tank. Plug the remote control cord into the slot marked remote control on the back of the machine. Plug power cord into a grounded electrical outlet. Turn the power switch to ON on the back of the
machine. The red light on the remote will turn ON once the machine is plugged into a power outlet and the ON/OFF switch is turn ON. The unit will take a couple of minutes to warm up the heater. During this time the machine cannot generate fog. The green light on the remote will turn ON once the machine is ready to produce fog. To emit fog press the green button on the remote. Z-1200II is controlled via the Z-8 remote control. For detailed instruction on the various functions on operating your Z-1200II Fog Machine, see the section titled Remote Control Operation.

Important: Always monitor tank fluid level as you are fogging. Running a fog machine with no fluid can
permanently damage the unit.
If your model includes a mounting bracket designed for overhead installation, it may be installed floor level or suspended overhead. If the unit is to be mounted using the bracket, it is important that the fog does not shoot directly at any ones face. Whatever installation method you choose, do not allow the unit to have more than a 15 degree angle or onclination. Note: A fluid level sensor is installed on the unit. The machine will stop to fog if the fluid is lower than the maximum level. If you experience low output, pump noise or no output at all, unplug immediately. Check fluid level, the external fuse, remote control connection and power from the wall. If all of the above appears to be O.K., plug the unit again. If fog does not come out after holding the remote button down for 30 seconds, check the hose attached to the tank to make sure there is fluid going through the hose. If you are unable to determine the cause of the problem, do not simply continue pushing the remote button, as this may damage the unit. Return the machine to your ANTARI dealer.

Specification

Model Number Power Supply Power Consumption Output Volume Tank Capacity Fluid Consumption Weight Dimensions(mm) Remote Included Z-1200II AC100-120V, AC220-240V / 50HZ-60HZ 1250 W ca. 500 m/min. 2.5 Liter 44 min./Liter 10.9 Kg. L458 W243 H177 Z-8
Remote Control Operation Z-8: 10 meter wired multi-function remote control with 5-PIN plug for ANTARI Fog Machine model Z-1200II.
The Interval knob adjusts the time between discharges when the timer function is engaged. The range is from 10 seconds to 250 seconds. The Volume knob controls the volume of the fog produced. The range is from 0% - 100% of maximum output. The yellow TIMER button controls the timer function. Depress the button to activate. When activated, the yellow light will turn ON. Adjusting the interval knob will determine the time between fog output (seconds). The duration of output is set at 15 seconds. The volume can be adjusted using the volume knob to control the amount of fog produced. The red CONTINUOUS button sets the machine to constant fog production. To activate this function, depress the red button. The volume knob can be used to regulate the volume of the steady stream of fog produced. The green MANUAL button will produce a continuous blast at maximum volume while the button is held down. When released, the manual function stops and the machine will return to the previous setting; timer, continuous, or stationary. Note: The continuous function will override the Timer function. Therefore, if both buttons have been depressed the Z-1200II will fog continuously. The manual function overrides all functions. When depressed and held down the Z-1200II will fog at maximum volume for as long as the button is held down, regardless of the machines setting at the time.

Performance Note All fog machines develop condensation around the output nozzle. Because this may result in some
moisture accumulation on the surface below the output nozzle, consider this condensation when installing your unit. All fog machines may sputter small amounts of fog occasionally during operation and for a minute or so after being turned off. All fog machines have a recycling period after long bursts when the machine will shut itself down for a short period in order to heat up again. During this time no fog can be produced.

Maintenance

Do not allow the fog liquid to become contaminated. Always replace the caps on the fog liquid container and the fog machine liquid tank immediately after filling. After every 40 hours of continuous operation, it is recommended to run a cleaning solution composed of 80% distilled water and 20% white vinegar through the system to prevent the accumulation of particulate matter in the heating element. The recommended cleaning regimen is as follows: 1. Empty all fog liquid from machine. Add cleaning solution to tank. Plug unit in and begin warm up. 2. Run unit in a well-ventilated area until tank is almost empty. Do not allow the pump to run dry. 3. Cleaning is now complete. Refill with fog liquid. Run the machine briefly to clear any cleaning solution from the pump and heater. 4. Do not operate the fog machine without liquid at any time. Note: All fog machines are prone to clogging due to the thick consistency of fog liquid and the high temperature at which it vaporizes. However, a properly maintained fog machine should provide years of reliable use. Clean with a dry cloth only. Store dry. Cleaning your fog machine regularly will help reduce costly replacement and repair charges.

Storage

When storing run distilled water (not tap water) through the system as described in the cleaning regimen above. This will help avoid any particles condensing inside the pump or heater.
Please read and save these instructions.
Antari Z-1200II on-board DMX Fog Machine Settings
DMX Setting for Z-1200II fog machines with on board DMX Channel A
0 - 5 = OFF = Volume Control ( 5% - 95%)
= Maximum Volume Output (100%)
The Z-1200II Fog Machine have on-board DMX control. These two models use 1 channel to control volume output operation. Each channel has a value range of 0 to 255. Timer functions such as duration and interval can be programmed using the DMX controller or the DMX control software being used by lighting and effects operator. If Channel A has a value from 0 to 5, the unit is OFF. Between the values 6 to 249 the volume of fog output is regulated. With 6 being the minimum volume of fog produced and 249 approaching the maximum. The volume output rises as the DMX value is increased. If Channel A has a value from 250 TO 255, the machine will operate at maximum output. Note: In the example above, if the machine were assigned the DMX address of 124, Channel A would correspond to DMX address 124. In general, Antari fog machines with onboard DMX conform to the following performance specifications: 1. Average Operating temperature = 250C 2. Fogger can maintain maximum output for 30 seconds or more 3. Fogger can maintain constant output at 30% volume setting (roughly a value of 75).