AOC 7F-SLK

17 inch Color Monitor

Users Manual

by Envision Peripherals, Inc. www.aocmonitor.com
Before operating your monitor, please read this manual thoroughly.

v2_123102

For Your Safety

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help.

Notice

1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibility of the user to correct such interference. As an ENERGY STAR Partner, Envision Peripherals, Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Warning

To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously high voltage is present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.

Precautions

Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions. Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided. The monitor should be operated only with the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. Disconnect the power cord to stop the power supply to the monitor.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. As a safety feature, this plug will only fit into a grounded power outlet. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug. Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges. Do not overload power strips and extension cords. Overloading can result in fire or electric shock. Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on the monitor. Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous voltage and other hazards. Please refer all servicing to qualified service personnel. To ensure satisfactory operation, use the monitor only with UL-listed computers which have appropriately configured receptacles marked between 100 - 240 V AC, Min. 3.5A. The wall socket should be installed near the equipment and should be easily accessible.

General Notes

Do not install the monitor near heat sources such as radiators or air ducts. Do not place monitor in direct sunlight or in areas with excessive dust, mechanical vibration or shock. Save the original shipping carton and packing materials in case you need to ship your monitor. Be sure to repackage your monitor as it was originally packed at the factory. Periodically clean your monitor with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinners, benzene, or abrasive cleaners, since these will damage the cabinet. Always unplug the monitor before cleaning it.

General Features:

17" (43.2 cm) Color Monitor Crisp, Clear Display for Windows Supports Resolutions up to 1280 x 1024 pixels @60Hz EPA ENERGY STAR

Package Contents

The box that your monitor was shipped in should have included the following items: 1. 7F-SLK Color Monitor 2. Power Cord 3. Quick Start Guide 4. Booklet (containing Warranty and Safety information)
Using the Right Power Cord
The supplied power cord is a NEMA 5-15 style plug. It is UL-listed and CSA labeled for 125 volts AC. If the monitor will be connected to your computers power outlet, use a minimum No. 18 AWG, type SJT or SVT three conductors cord with one end terminating with a male grounded plug, rated 10A, 250V, CEE-22. The other end must terminate with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration.
Before You Operate the Monitor
Installing & Removing the Base
Connecting the Wires Using the Power Cord Supplied
1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. 2. Connect the power cord into your monitor's power input socket. 3. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip.
Caution: Make sure the power cord is the correct type that is required in your area. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required). If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied).
Connecting the Wires Using An Optional Power Cord (Not Supplied)
The power cord supplied with your monitor can only be connected to a grounded electrical wall socket or power strip. If you wish to connect your monitor to a power supply using the power input socket on the back of your computer, you must purchase a power cord with CEE-22 terminated connectors (see illustration above).

Follow these steps: 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. 2. Connect the power cord into your monitor's power input socket. 3. Plug the other end of the power cord into the power output socket on your PC.

Operating Instructions

Front Panel Buttons
Shuttle Knob: Press this knob to open the OSD window or select a highlighted function. Rotate this knob to switch functions or adjust settings. Power Indicator: A green light indicates that the monitor is on. An orange light indicates that the monitor is in Off mode. Note: This monitor automatically turns on when it is plugged into an AC outlet.
Power: Press this button to put the monitor into Off mode. The power indicator will turn orange. Press and hold this button again to restore the monitor to normal operation mode. On-screen Display (OSD): Press the Shuttle Knob to open the OSD window and adjust settings on your monitor. (See next page.)
Adjusting the OSD Settings
1. Press the Shuttle Knob to open the OSD window. 2. Rotate the Shuttle Knob until the desired function is highlighted. 3. Press the Shuttle Knob again to open the functions window. 4. Rotate the Shuttle Knob to change the settings of the function.
5. To save and exit, select the exit function or leave the monitor alone for 10 seconds. If you want to adjust any other function, repeat steps 2-4. Note: When the OSD window is open, the input signal timing settings appear at the top. H: stands for horizontal frequency and V: stands for vertical frequency. 9
Plug & Play DDC1/2B Feature
This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC1 and DDC2B. The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information. The DDC2B is a bidirectional data channel based on the IC protocol. The host can request EDID information over the DDC2B.

Windows INF Driver File

Most computers will automatically configure your monitor to work with your computer. For optimal viewing of your monitor, download the AOC monitor driver. Follow these steps: 1. Go to www.aocmonitor.com 2. Click on SUPPORT to open the drivers web page. 3. Follow the directions on the web page to download and install the driver on your computer. Or go to www.aocmonitor.com/support/drivers.asp to directly access the driver web page.

Technical Support (FAQ)

Problem
Power LED is not ON No Plug & Play

Possible Solution

Make sure the power cord is properly connected to a grounded power outlet and to the monitor. Confirm that your computer is Plug & Play compatible. Confirm that your video card is Plug & Play compatible. Inspect the video cable and make sure that none of the pins are bent. Make sure the AOC monitor drivers are installed (AOC monitor drivers are available at: www.aocmonitor.com)

Picture is fuzzy Picture bounces or a wave pattern is present in the picture Power LED is ON (green or orange light is ON) but there is no video or picture. Missing one of the primary colors (RED, GREEN, or BLUE) Screen image is not centered or sized properly Picture has color defects (white doesnt look white)
Adjust the Contrast and Brightness settings. Move electrical devices away from the monitor. They may be causing electrical interference. Press a key on the keyboard or wiggle the mouse to re-activate the monitor. Make sure the video cable is properly connected to the computer. Inspect the video cable and make sure none of the pins are bent. Make sure your computer is operating correctly by pressing the CAPS LOCK key and observing whether the CAPS LOCK light turns ON or OFF.
Inspect the video cable and make sure that none of the pins are bent. Make sure the video cable is properly connected to the computer. Adjust the Horizontal, Vertical or Zoom settings in the OSD window.
Adjust the User Color setting in the OSD window.

Appendix

Specifications
CRT Size 17.0" (43.2 cm) 11.4 (29 mm) neck 0.25mm(D), 0.21mm(H) dot pitch 90 degree deflection Viewable image size Preset Display area Dot Clock Maximum Resolution Plug & Play 16.0 (40.6 cm) diagonal 11.8 (300 mm) X 9.1 (230 mm) 110 MHz 1280 x 1024 pixels VESA DDC1/2B TM Factory Preset Mode User Programmable Mode EPA ENERGY STAR Power Consumption (Maximum) Regulatory Compliance Input Video Separate Sync. H/V Sync. H-Frequency V-Frequency Input Video Signal Power Source
Red, Green, Blue Analog Interface H/V TTL Positive/Negative 30 kHz - 72 kHz 50 Hz -130 Hz Analog: 0.7 Vpp, 75 OHM, Positive Universal AC 100 - 240 V 50/60 Hz Yes 90 Watts UL, CSA, FDA, FCC, TV/GS, MPRII
Specifications (continued)
Environmental Considerations Operating Temp: 32 to 104F (0 to 40C) ambient Operating Humidity: 10% to 85% relative, non-condensing Signal Cable Attached Mini D-sub 15 Male
Optimal Viewing Mode: 1024 x 768 x 85 Hz

Factory Preset Timing Table

Standard

Resolution (in pixels)

640 480

Horizontal Frequency
31.5 KHz 31.5 KHz 43.3 KHz 53.7 KHz 68.7 KHz 64.0 KHz

Vertical Frequency

70 Hz 60 Hz 85 Hz 85 Hz 85 Hz 60 Hz

VESA / 85

1024 768

VESA / 60

1280 1024

Connector Pin Assignment

Pin Number

Description

Red Green Blue Ground Ground R-Ground G-Ground B-Ground 15 *
Ground Monitor Ground DDC-Serial Data H-Sync V-Sync / *V-Clk DDC-Serial Clock For DDC

Limited 3-Year Warranty

This is a warranty statement for AOC color monitors including those sold within North America as specified. Envision Peripherals, Inc. (EPI) warrants this product to be free from defects in material and workmanship for a period of three (3) years after the original date of consumer purchase. During this period, EPI will, at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except as stated below*. The parts or product that are replaced become the property of EPI. * This limited warranty does not cover any losses or damages that occur as a result of: Shipping or improper installation or maintenance Misuse Neglect Any cause other than ordinary commercial or industrial application Adjustment by non-authorized source Repair, modification, or installation of options or parts by anyone other than an EPI Authorized Service Center Improper environment
Excessive or inadequate heating or air conditioning or electrical power failures, surges, or other irregularities. This three-year limited warranty does not cover any of the product's firmware or hardware that you or any third party have modified or altered; you bear the sole responsibility and liability for any such modification or alteration. All express and implied warranties for the product (including the warranties of merchantability and fitness for a particular purpose) are limited in duration to a period of three (3) years for parts and labor from the original date of consumer purchase. No warranties (either expressed or implied) apply after this period. In the United States, some states do not allow limitations on how long an implied warranty lasts. Therefore, the above limitations may not apply to you. EPIs obligations and your remedies hereunder are solely and exclusively as stated here. EPIs liability, whether based on contract, tort, warranty, strict liability, or other theory, shall not exceed the price of the individual unit whose defect or damage is the basis of the claim. In no event shall EPI be liable for any loss of profits, loss of use or facilities or equipment or other indirect, incidental, or consequential damage. In the United States, some states do not allow the exclusion or limitation of incidental or consequential damages. Therefore, the above limitations may not apply to you.

Warranty (continued)

Although this limited warranty gives you specific legal rights, you may have other rights which may vary from state to state. In the United States of America, this limited warranty is only valid for products purchased in the Continental United States, Alaska, and Hawaii. Outside the United States, this limited warranty is only valid for products purchased in Canada. In the United States, to obtain service under this limited warranty: 1. Call EPIs Customer Service, RMA Department at the toll free number (888) 662-9888 for the nearest Authorized Service Center located in your area. 2. Ask for a Return Merchandise Authorization (RMA) number. 3. Deliver the product freight pre-paid to the EPI Authorized Service Center. If you cannot deliver the product in person: Pack it in its original shipping container (or equivalent) Put the RMA number on the shipping carton
EPI is not responsible for damage to inbound products that were not properly packaged. EPI will pay the return shipment charges within one of the countries specified within this warranty statement. EPI is not responsible for any costs associated with the transportation of products across international borders. This includes the international borders of the countries within this warranty statements. 2002 Envision Peripherals, Inc.
Insure it (or assume the risk of loss / damage during shipment) Pay one-way shipping charge