AOC 9KLR

19 inch Color Monitor

Users Manual

by Envision Peripherals, Inc. www.aocmonitor.com
Before operating your monitor, please read this manual thoroughly.

v3_123102

For Your Safety

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help.

Notice

1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibility of the user to correct such interference. As an ENERGY STAR Partner, Envision Peripherals, Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Warning

To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously high voltage is present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.

Precautions

Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions. Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided. The monitor should be operated only with the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. Disconnect the power cord to stop the power supply to the monitor.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. As a safety feature, this plug will only fit into a grounded power outlet. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug. Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges. Do not overload power strips and extension cords. Overloading can result in fire or electric shock. Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on the monitor. Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous voltage and other hazards. Please refer all servicing to qualified service personnel. To ensure satisfactory operation, use the monitor only with UL-listed computers which have appropriately configured receptacles marked between 100 - 240 V AC, Min. 3.5A. The wall socket should be installed near the equipment and should be easily accessible.

General Notes

Do not install the monitor near heat sources such as radiators or air ducts. Do not place monitor in direct sunlight or in areas with excessive dust, mechanical vibration or shock. Save the original shipping carton and packing materials in case you need to ship your monitor. Be sure to repackage your monitor as it was originally packed at the factory. Periodically clean your monitor with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinners, benzene, or abrasive cleaners, since these will damage the cabinet. Always unplug the monitor before cleaning it.

General Features:

19" (48.3 cm) Color Monitor Crisp, Clear Display for Windows Supports Resolutions up to 1600 X 1200 pixels @75Hz EPA ENERGY STAR

Package Contents

The box that your monitor was shipped in should have included the following items: 1. 9Klr Color Monitor 2. Power Cord 3. Quick Start Guide 4. Booklet (containing Warranty and Safety information)
Using the Right Power Cord
The supplied power cord is a NEMA 5-15 style plug. It is UL-listed and CSA labeled for 125 volts AC. If the monitor will be connected to your computers power outlet, use a minimum No. 18 AWG, type SJT or SVT three conductors cord with one end terminating with a male grounded plug, rated 10A, 250V, CEE-22. The other end must terminate with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration.
Before You Operate the Monitor
Installing & Removing the Base
Connecting the Wires Using the Power Cord Supplied
1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. 2. Connect the power cord into your monitor's power input socket. 3. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip.
Caution: Make sure the power cord is the correct type that is required in your area. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required). If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied).

Connecting the Wires Using An Optional Power Cord (Not Supplied)
The power cord supplied with your monitor can only be connected to a grounded electrical wall socket or power strip. If you wish to connect your monitor to a power supply using the power input socket on the back of your computer, you must purchase a power cord with CEE-22 terminated connectors (see illustration above).
Follow these steps: 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. 2. Connect the power cord into your monitor's power input socket. 3. Plug the other end of the power cord into the power output socket on your PC.

Operating Instructions

Front Panel Buttons
Shuttle Knob: Press this knob to open the OSD window or select a highlighted function. Rotate this knob to switch functions or adjust settings. Power Indicator: A green light indicates that the monitor is on. An orange light indicates that the monitor is in Off mode. Note: This monitor automatically turns on when it is plugged into an AC outlet.
Power: Press this button to put the monitor into Off mode. The power indicator will turn orange. Press and hold this button again to restore the monitor to normal operation mode. On-screen Display (OSD): Press the Shuttle Knob to open the OSD window and adjust settings on your monitor. (See next page.)
Adjusting the OSD Settings
1. Press the Shuttle Knob to open the OSD window. 2. Rotate the Shuttle Knob until the desired function is highlighted. 3. Press the Shuttle Knob again to open the functions window. 4. Rotate the Shuttle Knob to change the settings of the function.
5. To save and exit, select the exit function or leave the monitor alone for 10 seconds. If you want to adjust any other function, repeat steps 2-4. Note: When the OSD window is open, the input signal timing settings appear at the top. H: stands for horizontal frequency and V: stands for vertical frequency. 9
Plug & Play DDC1/2B Feature
This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC1 and DDC2B. The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information. The DDC2B is a bidirectional data channel based on the IC protocol. The host can request EDID information over the DDC2B.

Windows INF Driver File

Most computers will automatically configure your monitor to work with your computer. For optimal viewing of your monitor, download the AOC monitor driver. Follow these steps: 1. Go to www.aocmonitor.com 2. Click on SUPPORT to open the drivers web page. 3. Follow the directions on the web page to download and install the driver on your computer. Or go to www.aocmonitor.com/support/drivers.asp to directly access the driver web page.

Technical Support (FAQ)

Problem
Power LED is not ON No Plug & Play

Possible Solution

Make sure the power cord is properly connected to a grounded power outlet and to the monitor. Confirm that your computer is Plug & Play compatible. Confirm that your video card is Plug & Play compatible. Inspect the video cable and make sure that none of the pins are bent. Make sure the AOC monitor drivers are installed (AOC monitor drivers are available at: www.aocmonitor.com)
Picture is fuzzy Picture bounces or a wave pattern is present in the picture Power LED is ON (green or orange light is ON) but there is no video or picture.
Adjust the Contrast and Brightness settings. Move electrical devices away from the monitor. They may be causing electrical interference. Press a key on the keyboard or wiggle the mouse to re-activate the monitor. Make sure the video cable is properly connected to the computer. Inspect the video cable and make sure none of the pins are bent. Make sure your computer is operating correctly by pressing the CAPS LOCK key and observing whether the CAPS LOCK light turns ON or OFF. Inspect the video cable and make sure that none of the pins are bent. Make sure the video cable is properly connected to the computer. Adjust the Horizontal, Vertical or Zoom settings in the OSD window. Adjust the User Color setting in the OSD window.
Missing one of the primary colors (RED, GREEN, or BLUE) Screen image is not centered or sized properly Picture has color defects (white doesnt look white)

Appendix

Specifications
CRT Size 19.0" (48.3 cm) 11.4 (29 mm) neck 0.21mm(H), 0.25mm(D) dot pitch 90 degree deflection Viewable image size Preset Display area Dot Clock Maximum Resolution Plug & Play 18.0 (45.7 cm) diagonal 13.6 (346 mm) X 10.2 (260 mm) 200 MHz 1600 x 1200 pixels VESA DDC1/2B TM Factory Preset Mode User Programmable Mode EPA ENERGY STAR Power Consumption (Maximum) Regulatory Compliance Input Video Separate Sync. H/V Sync. H-Frequency V-Frequency Input Video Signal Power Source
Red, Green, Blue Analog Interface H/V TTL Positive/Negative 30 kHz - 95 kHz 50 Hz -160 Hz Analog: 0.7 Vpp, 75 OHM, Positive Universal AC 100 - 240 V 50/60 Hz Yes 130 Watts UL, CSA, FDA, FCC, TV/GS, TCO92, Windows XP Logo
Specifications (continued)
Environmental Considerations Operating Temp: 32 to 104F (0 to 40C) ambient Operating Humidity: 10% to 85% relative, non-condensing Signal Cable Attached Mini D-sub 15 Male
Optimal Viewing Mode: 1280 x 1024 @ 85 Hz
Factory Preset Timing Table

Standard

Resolution (in pixels)

640 480

Horizontal Frequency
31.5 kHz 31.5 kHz 43.3 kHz 53.7 kHz 68.7 kHz 85.9 kHz 91.1 kHz 93.8 kHz

Vertical Frequency

70 Hz 60 Hz 85 Hz 85 Hz 85 Hz 85 Hz 85 Hz 75 Hz

VESA / 85

1280 1024

VESA / 75

1600 1200

Connector Pin Assignment

Pin Number

Description

Red Green Blue Ground Ground R-Ground G-Ground B-Ground 15 *
Ground Monitor Ground DDC-Serial Data H-Sync V-Sync / *V-Clk DDC-Serial Clock For DDC

Specialized System Integration 2519 Data Drive Louisville, KY 40299 502-491-9951 sales@ssi-ky.com
Celeron 850 Celeron 900 Celeron 1.1 Celeron 1.2 Celeron 1.3 PIII 1.0 EB P4 1.6 GB P4 1.7 GB P4 1.8 GB P4 1.9 GB P4 2.0 GB P4 2.2 GB

20 GB 1425 1730

40 GB 1450 1750

60 GB 1490 1790

80 GB 1540 1840

100 GB

1620 1920
All systems include the following: ! Microsoft Intelli-Mouse ! Integrated Sound and Network Interface ! Altec Lansing AV200 Powered Speakers ! Western Digital 7200 RPM Hard Drive ! 104 Key Keyboard ! 56K Internal Modem ! 128 MB RAM (Celeron & PIII 133 Mhz / PMhz RDRAM) ! 3 Year Warranty (Depot) ! 3.5 Floppy Drive & CD-ROM Drive ! Choice of Windows 98 SE, Windows ME or Windows XP Home Edition ! Norton Anti-Virus ! Video Adapter (Celeron & PIII 4MB Integrated 3D / P4 ATI Xpert 2000 Pro w/ 32MB)

Special Options Pricing

**Pricing applies only with purchase of new computer.

Monitors:

15 Color Monitor 15.28mm (AOC 5E) 17 Color Monitor 17.27mm (AOC 7KLR) 19 Color Monitor 19.25mm (AOC 9KLR) 15 Color LCD Flat Screen Monitor (AOC LM500) 17 Color LCD Flat Screen Monitor (AOC LM700) 670

Printers:

HP Deskjet 630c 6ppm blk / 2ppm color, 600x300 dpi color HP Deskjet 648c 6ppm blk / 3ppm color, 600x300 dpi color HP Deskjet 845c 8ppm blk / 5ppm color, 600x1200 dpi color HP Deskjet 842c (same features as 845c), Lime color lid 99 119
Visit Our Website at http://www.ssi-ky.com