USERS MANUAL

A42W64AT4
Thank you very much for choosing the Envision Series Plasma TV. We recommend that you take a few minutes to read carefully through this manual before installing and using the TV.

CONTENT

IMPORTANT SAFETY INSTRUCTIONS...1 Precautions and Reminders.2 Features and Function.4 Front Panel Control.5 Basic Installation.6 Connection to other equipment.7 Remote Control Function...9 OSD Menu Descriptions Main Menu.....10 Setup Menu....10 Video Menu....11 Audio Menu.11 Feature Menu....12 EPG.13 TVChannel..13 Specifications.....14 Troubleshooting....15
IMPORTANT SAFETY INSTRUCTIONS
Read before operating equipment
1. 2. 3. 4. 5. 6. Read and follow all instructions. Do not operate this apparatus near water. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not block any of the ventilation openings. Clean only with a dry cloth. Do not defeat the safety purpose of the polarized or grounding-type plug.A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and third grounding prong. The wide blade or third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. This product may contain lead and mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org Damage Requiring Service -The appliance should be serviced by qualified service personnel when: The power supply cord or the plug has been damaged; or Objects have fallen, or liquid has been spilled into the appliance; or The appliance has been exposed to rain; or The appliance does not appear to operate normally or exhibits a marked change in performance; or The appliance has been dropped, or the enclosure damaged. 14. Tilt/Stability- All televisions must comply with recommended international safety standards for tilt and stability properties of its cabinet design. Do not compromise these design standards by applying excessive pull force to the front, or top, of the cabinet which could ultimately overturn the product. Do not endanger yourself, or children, by placing electronic equipment/toys on the top of the cabinet. Such items could unsuspectingly fall from the top of the set and cause product damage and/or personal injury. 15. Wall or Ceiling Mounting- The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer. 16. Power Lines- An outdoor antenna should be located away from power lines. 17. Outdoor Antenna Grounding- If an outside antenna is connected to the receiver, make sure the antenna system is grounded so as to provide protection against voltage surges and built up of static charges. Section 810 of the National Electric Code, ANSI/NFPA No.70-1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure below. 18. Object and Liquid Entry- Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. 19. Battery Usage CAUTION To prevent battery leakage that may result in bodily injury, property damage, or damage to the unit: Install all batteries correctly, with + and - aligned as marked on the unit. Do not mix batteries (old and new or carbon and alkaline, etc.). Remove batteries when the unit is not used for a long time. 20. Keep this manual for future reference

7. 8. 9.

10. 11.
Example of Antenna Grounding as per NEC - National Electric Code

GROUND CLAMP

ANTENNA LEAD IN WIRE
Note to the CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

ANTENNA DISCHARGE UNIT

(NEC SECTION 810-20) (NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21) (NEC SECTION 810-21)

GROUND CLAMPS

ELECTRIC SERVICE EQUIPMENT
POWER SERVICE GROUNDING ELECTRODE SYSTEM

(NEC ART 250, PART H)

Precautions and Reminders
Do not place unit on uneven surfaces.
Do not place the TV in confined spaces or in a box when using it.
Unplug immediately if there is any malfunction, Unplug immediately if other foreign materials like no video, no audio, smoke or a bad odor. are put inside TV box or if the TV fell down.
Do not throw any object like metals or flammable materials into the TV set. Prohibit/Avoid opening TV cabinet
DO NOT use liquid cleansers or aerosol Avoid direct sunlight, dusty, high humidity and cleansers to clean the plasma display. Dilute a smoky areas. neutral detergent with water and wipe with a soft cloth or gently clean with some absorbent cotton. Remember to unplug the AC mains cord before cleaning the display.
Make sure to unplug the unit when not in use Call service personnel to clean the internal part for a long period of time (2 days). of the TV once a year.
Do not cover or block any vents and openings. Do not place the unit near water, such as Inadequate ventilation may shorten the life of bathtub, washbasin, kitchen sink laundry tub, the display unit and cause overheating. swimming pool or in a damp basement.
Notice for Remote Control

Avoid Dropping

Avoid Liquids

Avoid Aerosol Cleaners

Features and Function
42 inch107cmLarge Screen Flat Panel Plasma Display Panel Resolution: WVGA 852 x 480 Pixels MAX Brightness of Panel: 1500 Cd/m2 MAX Contrast Ratio of Panel: 10000:1 View Angle: Greater than 160 Internal TV Tuner, Air69 channels Cable135 channels Frequency Range55.25MHz to 859.25MHz ATSC receiver, MPEG-2 decoder NTSC receiver, Video decoder Dual Video, Dual S-Video Dual Y Pb Pr 480i, 480P, 720P, 1080iHDTV Ready PC D-SUB 15Pin INPUT D-SUB Vertical refresh rate 50Hz to 85 Hz D-SUB Horizontal frequency 31KHz to 80KHz DVI-D SignalTMDSINPUT, Support HDTV, SDTV MIPS controller technology Auto Scan TV Channels Factory Presets Universal Power Supply designed for worldwide application 350 W (Power consumer) Closed Caption / V-chip For USA

Front Panel Control

MODE MENU - VOL + - CH +
Mode: Press to select input signal modes or use as Enter in Menu operation. Menu: Press to enter Menu or exit Menu. Left: Press to decrease the sound volume level or move Left in Menu operation. Right: Press to increase the sound volume level or move Right in Menu operation. Down: Press to select the next lower Programme number or move Down in Menu operation. Up: Press to select the next higher Programme number or move up in Menu operation Power switch: Press to power on or power off the TV set. LED: Power Indicator. IR: Remote Control Sensor.

Basic Installation

1. Connect TV Cable and Power Cord to this PDP TV Set. 2. Plug Power Cord to your home power outlet. 3. Check front panel LED for proper power connection: Blue color indicates this TV set is powered on; Red color indicates this TV set is in standby state. 4. Push POWER KEY on Remote Control or Power key on Front panel controls to switch the TV from stand by state to ON state. This TV will power on and you can see display on screen within a few minutes. 5. Once you see information displayed on screen, press Digital button on Remote Control or MODE key on front panel continuously to select TV as input source. TV channel information will be displayed. 6. Use Auto channel search in Setup Menu to search all channels in your location. Refer to page 8 for Setup Menu operation procedure. 7. After Auto channel search is completed, press CHup or CHdown key on remote control to select the next lower or higher channel. Refer to the following pages for operating procedures: Remote Control page 9. Setup Menu page 10. TV Channel Arrangement page 13.

POWER KEY

Ch14.0

12:00AM

TV channel information
Connection to other equipment
Please connect this TV Set to other equipment as picture below. You may have many types of equipment as: DVD, VCD, VCR, Set Top Box, X-Box and so on. (View from back of the TV set,left to right)

INPUT CONNECTION OF VIDEO SIGNAL(DVD/VCD/VCR)

s-video

R AV1-INPUT
We have 2 component signal input jacks: Y Cb Cr and Y Pb Pr. The R / L is Audio input for every Y Cb Cr and Y Pb Pr. If your DVD or Set Top Box have Y Cb Cr or Y Pb Pr output, you can connect it to Y Cb Cr or Y Pb Pr input jack. And select to Y Cb Cr or Y Pb Pr source input. Some DVD or Set Top Box need to set to Y Cb Cr or Y Pb Pr output Notice: If you see that display abnormality in screen, you need to check the cable connection and DVD setup.

G B R R W

INPUT CONNECTION OF PC SIGNAL(PC/DVD)
Notice: If you see that display abnormality in screen, you need to check the cable connection and DVD setup.
Notice: The PC output can not set out of range.The highest resolution input is 1280 X 1024 / 60Hz. Some PC models cannot be connected to the set.
24PIN DVI R/L INPUT 15PIN DVI R/L INPUT
D-SUB 15 Pin: Connect D-SUB signal cable VGA cable from PC to D-SUB jack at the back of this display. And connect the earphone cable from PC earphone output jack to AUDIO input jack near to the D-SUB jack. Setup: Use the key Digital Remote Control Transmitter or MODE on Front panel controls in key to select source to VGAstate. Then turn on the PC. DVI-D: Connect DVI-D 24 Pin signal cable TMDS cable from equipment with DVI-D jack to the back of this display. And connect earphone cable from equipment with earphone output jack to AUDIO input jack near the DVI-D jack. Setup: Use the key Digital Remote Control Transmitter or MODE on Front panel controls in key to select source to DVIstate. Then turn on the equipment.

Remote Control Function

Wide Mode Normal, Zoom ,Wide, Cinema display select EPG Display the state, source TV TV source select, into TV state SLEEP Select timer into power down state. off306090off CC To select close caption options (CC1,CC2) ENTER To enter sub Menu or sub item. MENU To enter Menu mode. MUTE Mute the sound Vol up / Vol down Press Vol up/ Vol down key to adjust volume. 0~9 number To enter TV channel number To enter sub channel number for digital channels.
POWER The TV Set turn on /turn off key

Wide Mode EPG POWER

Digital
Video AV1 CVBS Rear /AV1 S-Video Rear/ AV2 CVBS Side/ AV2 S-Video Side / AV3 component 1/ AV4 component 2 Digital VGA/DVI source input MTS To select audio program options Up/Down Move the cursor up and down on the Menu left / right Use left / right to select or adjust an item.

D ow n

M en u

Mute Vol up CH up

Vol down

CH down

EXIT To exit Menu or other OSD. CH up / CH down Press to select the next lower or higher Program number. Pre-CH TV channel return, see last TV channel.

Pre-CH

OSD Menu Descriptions
Main Menu 1. Press MENU key on remote control or front panel controls to bring up Main Menu. 2. Press or to move the cursor up and down the sub menu list. 3. Press or to select sub menu item. 4. Press "Enter" to enter sub-item then use or to adjust. Setup Menu
1. Tuning Band: Select TV signal source between Air and Cable. Select Cable if you are connecting to a cable box and select Air if you are directly connecting to the antenna. 2. DTV Signal: Display signal strength to aid antenna adjustment. 3. Auto Ch Search: Automatically scan and store all TV channels. 4. Manual Ch Set: Enter channel setup table. 5. Channel Labels: Display and edit channel names. 6. Menu Language: Select language for menu (English Espaol Franais Portuguese).
DTV signal menu indicates signal strength in real-time. Auto channel scan menu displays channel number being scanned.
Manual Channel Set Menu Displays all the channel numbers that are found. Tune either to ATSC or NTSC channels. Add or delete Channel number.
Channel Labels Menu allows user labeling.
Video Menu. 1. Press or to move the cursor up or down the sub-item list. 2. Press "Enter" to enter the highlighted sub-item menu. 3. Press or to adjust the value of the sub-item. 4. Press "Enter" again to exit the sub-item.
Contrast: Contrast adjustment, 0 ~ 100. Brightness: Brightness adjustment, 0 ~ 100. Color: Color chroma adjustment, 0 ~ 100. Tint: Tint adjustment, 0 ~ 100. Aspect Ratio: Aspect Ratio selection. Normal Zoom Wide Cinema. Settings: Restore default setting.
Audio Menu 1. Press or to move the cursor up or down the sub-item list. 2. Press "Enter" to enter the highlighted sub-item menu. 3. Press or to adjust the value of the sub-item. 4. Press "Enter" again to exit the sub-item.

Audio Language: English Spanish French Portuguese. Bass: Bass adjustment, 0 ~ 100. Treble: Treble adjustment, 0 ~ 100. Balance: Balance adjustment, 0 ~ 100. Restore Default: Restore Audio Language, Treble, Bass, and Balance setting to default.
Feature Menu 1. Press or to move the cursor up or down the sub-item list. 2. Press "Enter" to enter the highlighted sub-item menu. 3. Press or to adjust the value of the sub-item. 4. Press "Enter" again to exit the sub-item.
Time Set : The default time when you first set up theTV is 12:00 midnight. The internal clock starts from 12:00am. In the time set menu, first select the time zone you are in and manually change the time to the present time. Press Enter to confirm the time and exit the menu. Note that whenever you switch the MAINS off, you need to set the time again when you turn the TV on. Sleep Timer: Select minutes into standby Off 90. Password Set: Enter and change Parental Control Password. Parental Control: Setup TV and Movie rating controls. White Screen:Press Enterto white screen.
Parental Control Menu: Controls viewing of rated TV and Movie programs. Note:Need password to change settings. Initial Default password is: 0000. Important : If you have forgotten your Password Use the code [0711] to enter into the Password Set menu item to change your password. You can also use the code [0711] to change your Parental Controls settings.

Closed Captions section

1. Press CC key on remote control to select closed captions mode.
NTSC TV: ATSC TV: Off.CC1.CC2. Off.CS1.CS2. CC1
2. Select desired closed caption mode. 3.Closed captioning for analog NTSC channels is transmitted as CC1/CC2/CC3/CC4.Closed captioning for digital channels is transmitted as CS1/CS2/CS3 /CS4/CS5/CS6 or occasionally CC1/CC2/CC3/CC4. You need to select the option you want for analog channels and digital channels separately.

NTSC TV

ATSC TV EPG Press the EPG key on the remote control to display the Electronic Program Guide (EPG). A message window will be displayed on screen.

EPG Message Window

TV channel arrangement

Ch 5.2

Analog NTSC channels are Numbered as2.0, 5.0, 11.0 etc. Digital ATSC channels are numbered as 2.1, 5.1, 5.2, 11.1, 11.2 etc depending on your local transmittors. Note that each digital channel may comprise of several sub-channels. For your convenience, this television groups all analog channels together followed by all digital channels together. To select a digital channel using the remote control: 1. To go to channel 5.2, enter main channel number (5). 2. Press the key. 3. Enter the sub-channel number (2).

Specifications

Screen size Aspect Display pixels Effective display size Number of color Contrast Ratio Peak brightness TV Tuning Sound system Color system AV1 ( S_Video/Video) AV2 ( S_Video/Video) Video Mode AV3 / AV4 COMPONENT X 2 (Y Cb Cr/Y Pb Pr) Signal input Plug and play Support Frequency PC Mode

Specification

42 inch plasma display panel 16:x 480 (WVGA) 932mm x 532mm 16.7 million colors 10000:1 (in dark room) 1500 cd/ 1 Tuners, Air:69 channels Cable:135 channels M ATSC / NTSC NTSC NTSC NTSC NTSC 480i 1080i YCbCr/YPbPrx 2 480P 720P AnalogD-Sub 15 pin DDC / 2B FH:31KHz to 80KHz FV:50Hz to 85Hz Video RCA x 1 S-Video1 x 1 Video RCA x 1 S-Video2 x 1 Audio: L/R x 1 Audio: L/R x 1

Panel Spec

TV Mode

Audio: L/R x 2

DVI Mode
Environment Dimension Net weight Accessory
VESA: 640 x 480 VESA: 800 x 600 D-Sub Mode VESA: 1024 x 768 VESA: 1280 x 1024 D-Sub Audio Earphone (3.5) Signal input DigitalDVI-D 24 pin Plug and play DDC / 2B 720P DVI Mode 1080i 480P DVI Audio Earphone (3.5) Power input sources AC 100-240V , 50/60Hz Power consumption 350W Operation Temperature + 0 C ~ + 40 C Storage Temperature - 10 C ~ + 50 C Humidity 10% -- 85% Width x Height x Thickness 1038 x 726.5 x 240 (mm) With Stand 34Kg Remote Control Transmitter, Battery X 2, Power Cord, Users Manual, RCA Cable, D-SUB Cable,DVI Cable.

Troubleshooting

Symptoms
Picture freezes in antenna mode. The TV does not react to remote controller commands. Picture breaks up in DVI mode, especially when a set top box is connected. The picture is jerky or is corrupted (multiple small square boxes seen) in ATSC mode.

Checks

Please ensure the antenna is properly connected. Please switch off the mains and switch on again. Re-install the channels if needed. The TV is trying to read the HDCP code sent by the set top box. Please switch off the set top box and switch on again. The signal could be weak. Check the DTV signal via Menu --> Setup --> DTV Signal. Adjust the direction of your antenna to improve the signal. Re-install the channels if needed. Press the channel number to check if the channel exists, if yes, go to the Manual Channel Set Menu (Menu-->Setup--> Manual ch set), and add the channel. Go to the Setup Menu (Menu-->Setup) and install the channels again, searching Air/Cable as appropriate. Check the power cord and power outlet. Check whether the TV power switch is on. Verify the front panel LED is showing blue color. Check connections for the selected input source. Verify that external signal for the selected input is active. Check Video/Audio settings. The signal could be weak. Check the DTV signal via Menu --> Setup --> DTV Signal Adjust the direction of your antenna to improve the signal Re-install the channels if needed. Check antenna connection, aerial location, and direction. Check and relocate nearby electrical appliances. Check fluorescent lights. Check cars/motorcycles. Check antenna connection, aerial location, and direction Re-scan Channels.

Some channels are missing / are not found.

No Picture, No Sound

Interference,Noisy
Distorted picture,Noisy Check whether colour setting is at minimum. Adjust video menu picture settings or reset to default. No Colour,Normal Sound Check audio input connections. Check whether TV audio is in MUTE mode. Adjust audio volume to audible level. Normal Colour,No Sound
The plasma TV panel is manufactured using an extremely high level of precision technology, however, sometimes some parts of the screen may be missing picture elements or have luminous spots. This is not a malfunction. Do not allow a still picture to be displayed for an extended period, as this can cause a permanent after-image to remain on the Plasma TV. Examples of still pictures include logos, video games, computer images, and Teletext. Note: The permanent after-image on the Plasma TV resulting from fixed image use is not an operating defect and as such is not covered by the Warranty. This product is not designed to display fixed images for extended periods of time. The signal is too weak to display a picture. Try to re-orient the antenna to a suitable direction and auto-tune again.
Some parts of the screen do not light up

After-images appear

DTV signal jumps from 0 to 100 and back.
No closed captioning seen when the TV is connected to a set top box.
Press the CC button on the remote controller to switch off the closed captioning. Then switch it on again.
Envision Peripherals Inc. 47490 Seabridge Dr. Fremont, CA 94538 www.AOCdisplay.com Tech Support: 1-888-662-9888

If your screen model is not listed below please check www.ergoindemand.com for the latest version of this chart.
SCREEN CONFIGURATION CHART
Model PDP4249ED PDP4290 PDP4294 PDP4298ED PDP5090 EMP 420 EMP420A/B SV 4201 SV 4201H SV-4202IQ HPT-500AW A42W64 A42HD84 A42W64AT4 PDP7859 PD46W1 PD5000 d:4222 d:4232 d:4742M d:4742DII d:5032 MP4205 DP-42GM DP-42SM DP-42WM DSP-4210 PD42S20W PD46C10 W4200 W4200ED W4201C W5001C DG4200 Revolution I P42HC P50 HD-150 HD-50 P5070 P5071 DTS-4230 DTS42PT DTS42W L42W761 FPP-42HD20 FPP-42HD25 FPP-50HD20 FPP-50HD25 P42HCA11WA P42HCA11WH P42HCA30WH P42HHA10US P42HHA10WS P42HHA30WS P42HHA40US P42HVA40 P42VCA21UH P42VCA30WH P42VHA20US P42VHA30WS P42XHA40US P42VHA51WS P50XCA11UH P50XCA30WH P50XHA10US P50XHA30WS P50XHA40US P50XTA51US PDS-5001 ScrewSize M6 M8 M8 M8 M8 M5 M5 misc misc M8 M8 M6 M6 M6 misc M6 M8 M8 M8 M8 M8 M8 M8 M5 M5 M5 misc M4 M6 M8 M8 M8 M8 M8 M4 M5 M8 M4 M8 M8 M8 M8 M8 M8 M6 M4 M4 M4 M4 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 ScrewLength 25 misc misc 12 misc 12 misc 40
See chart below to determine the fasteners to use with your screen. If your screen has a note in the far right column, then reference it on the last page.
Manufacturer Akai Akai Akai Akai Akai Akira Akira Akira Akira Akira Akira AOC AOC AOC Ben Q Ben Q Boxlight byd:sign byd:sign byd:sign byd:sign byd:sign Cornea Systems Daewoo Daewoo Daewoo Daewoo Daewoo Daewoo Dell Dell Dell Dell Digimate Dreamvision Dukane Dukane DWIN DWIN EIZO EIZO Electrograph Electrograph Electrograph Envision Faroudja Faroudja Faroudja Faroudja Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu
ScreenSize 42" 42" 42" 42" 50" 42" 42" 42" 42" 42" 50" 42" 42" 42" 42" 46" 50" 42" 42" 47" 47" 50" 42" 42" 42" 42" 42" 42" 46" 42" 42" 42" 50" 42" 42" 42" 50" 50" 50" 50" 50" 42" 42" 42" 42" 42" 42" 50" 50" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 50" 50" 50" 50" 50" 50" 50"
Washer multi none none none none multi multi misc misc none none multi multi multi misc multi none none none none none none none multi multi multi misc multi multi none none none none none multi multi none multi none none none none none none multi multi multi multi none none none none none none none none none none none none none none none none none none none none none
Spacer none 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 5.6mm ID 5.6mm ID misc misc 8.7mm ID 8.7mm ID none none none misc none 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID none none none none misc none none 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID none none none none 8.7mm ID none none 8.7mm ID 8.7mm ID 8.7mm ID none none none none none none none none none none none none none none none none none none none none 8.7mm ID 8.7mm ID 8.7mm ID none none 8.7mm ID

1 of 14

4900 Industry Drive Central Point, OR 97502 (800) 888-6024 or (541) 779-3763 Fax: (541) 779-0829 www.ergoindemand.com ISSUED: 01-12-06 SHEET #: 202-9084-27 09-30-09
Manufacturer Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Fujitsu Gateway Gateway Gateway Gateway Gateway Gateway Gateway Gateway H&B H&B H&B H&B H&B Harsper Harsper Harsper Hewlett Packard Hewlett Packard Hewlett Packard Hewlett Packard Hewlett Packard Hewlett Packard Hewlett Packard Hewlett Packard Hewlett Packard Hewlett Packard Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi Hyundai Idex Integra
ScreenSize 50" 50" 50" 55" 55" 61" 63" 63" 63" 42" 42" 42" 42" 42" 46" 50" 50" 42" 42" 50" 50" 50" 42" 42" 50" 32" 37" 42" 42" 42" 42" 42" 47" 47" 50" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 50" 50" 50" 50" 50" 50" 42" 42" 50" PDS-5002 PDS-5003 PDS-5004 P55XHA30WS P55XHA40US PDS-6101 P63XHA30US P63XHA30WS P63XHA40US GTW-P42M102 GTW-P42M203 GTW-P42M303 GTW-P42M403 GTW-P42M504 GTW-P46M103 GTW-P50M203 GTW-P50M603 HP-4250B-N HP-4250V-N HP-5000B-N HP-5000V-N HP-5500V-N HP-4200 HP-4250 HP-5000 HP-LC3200N HP-LC3700N LC4276N PE4200N PL-4200N PL4260N SL4278N LC4776N SL4778N PL-5000N 42EDT41 42HDF52 42HDM70 42HDS52 42HDS69 42HDT20 42HDT50 42HDT51 42HDT52 42HDT55 42HDT70 42HDX60 42HDX62 42HDX99 CMP402HDU CMP4120HDU CMP4121HDU, CMP4201U CMP4202U CMP4203U CMP420V1 CMP420V2 CMP4211, CMP4211U, CMP4212, CMP4212U, 50HDA39 50HDT50 50HDT55 50HDX60 CMP5000WXE CMP5000WXU PD421 PDM4276PC PLA-50FP1

ScrewSize M4 M4 M4 M6 M6 M6 M6 M6 M4 M4 M4 M4 M4 M4 M4 M4 M4 M4 M4 M6 M6 M6 M6 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8

ScrewLength 40 40

Washer multi multi multi multi none none none none multi multi multi multi multi multi multi multi multi multi multi none multi multi none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none
Spacer none none none none none none none none none none none none none none none none none none none none none none none 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID

Notes 11

6 of 14
Manufacturer Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Panasonic Philips Philips Philips Philips Philips Philips
ScreenSize 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 46" 46" 46" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 58" 58" 58" 58" 58" 58" 58" 58" 58" 42" 42" 42" 42" 42" 42"

Model TH-42PX25U/P TH-42PX50U TH-42PX500U TH-42PX600U TH-42PX60U TH-42PX75 TH-42PX77 TH-42XVS30 TH-42PZ700U TH-42PZ80U TH-42PZ85U TH-46PZ80U TH-46PZ85U TH-46PZ85X PT-50PD2-P PT-50PD3-P PT-50PD4-P PT-50PHD4-P TH-50PF9UK TH-50PF10EK TH-50PHD3U TH-50PHD5U TH-50PHD5UY TH-50PHD6 TH-50PHD6EX/BX TH-50PHD6UY TH-50PHD7UY TH-50PHD7WK/WS TH-50PHD8UK TH-50PHW5 TH-50PH9UK TH-50PH10EK/BS TH-50PH10UK TH-50PM50U TH-50PWD8UK TH-50PX20U/P TH-50PX25U/P TH-50PX30U/P TH-50PX500U/P TH-50PX50U/P TH-50PX6U TH-50PX600U/P TH-50PX75 TH-50PX77 TH-50PX700 TH-50PX80U TH-50PX80X TH-50PZ77U TH-50PZ700U TH-50PZ750U TH-50PZ80U TH-50PZ85U TH-50PZ85X TH-50XVS30 TH-50XVS30U/P TH-58PE75U TH-58PH10EK/ES TH-58PH10UK TH-58PX600U TH-58PX60U TH-58PX75U TH-58PX700 TH-58PZ700U TH-58PZ750U BDH4241V BDS4241V 42FD9934 42FD9935 42FD9944 42FD9954
ScrewSize M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M5 M5 M5 M5
Washer none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none multi multi multi multi
Spacer 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID 8.7mm ID none none none none

Notes 2

7 of 14
Manufacturer Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Philips Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer Pioneer
ScreenSize 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 46" 47" 47" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 52" 52" 63" 42" 42" 42" 42" 42" 42" 42" 42" 42" 43" 43" 43" 43" 43" 43" 43" 43" 43" 43" 43" 43" 43" 43" 43" 43" 43" 50" 42FX9020/37 42FW9020 42FW9030 42FW905 42FW9220/37 42FW997 42FW9975/37 42HF7945D/27 42PF5321D/37 42PF7320A 42PF7321D/37 42PF7421D 42PF9431D/37 42PF9630A 42PF9730A 42PF9731D 42PF9831D 42PF9936 42PF9936D 42PF9956 42PF9966 42PF9976 42PF9996 42PFL5332D 42PFL7332D/37 42PFL9900D BDS4611 47PFL5432D 47PFL9732D/37 BDH5021V/27 50FD9955 50FD9956 50PF7320 50PF7320A 50PF9431D 50PF9630A 50PF9956 50PF9966 50PF9986 BDH5011 52PFL7422D/37 52PFL7432D/37 63PF9631D/37 PDP-424MV PDP-425CMX PDP-427CMX PDP-4270HD PDP-4271HD PDP-4272HD PDP-4280HD PRO940HD PRO950HD PDP-4300 PDP-4304 PDP-4310HD PDP-4312 PDP-4330HD PDP-433CMX PDP-433PU PDP-4340 PDP-4341HD PDP-4345HD PDP-434CMX PDP-434PU PDP-4350HD PRO800HD PRO910 PRO920HD PRO930HD MC-505HD

none multi none multi none none none none washer none multi multi multi multi multi multi multi multi multi multi multi multi none none none none

13 of 14

If your screen model is not listed below please check www.peerlessmounts.com for the latest version of this chart.
NOTES (only look at the note that applies to your screen from the previous table) * The mount includes 12.7mm tall spacers 1 All hardware may not be included. If you are missing the additional fasteners needed for your screen, then please contact Customer Service at 1-800-888-6024. 2 If back of screen has a bumpout at bottom, then you may need to shift the brackets up so mount would miss it. 3 Remove the knobs on the back of the screen. Attach the mounting brackets to the mounting holes where the knobs used to be. 4 Use outter-most mounting holes 5 Remove cover, knob, handle, or original screws from TV before attaching bracket. 6 If back of screen has a bumpout, or if mounting holes lie in pockets, then use M4 X 25 mm screw with 12.7mm tall spacers 7 If screw is too small, then use M5 X 12 mm screw. 8 If mounting holes lie inside pockets, then use M8x25mm screws with 8.7mm ID spacers 9 If screen bumpout hits mount, then contact Customer Service for 15.9mm tall spacers ( not included ) 10 Use M8 x 25mm screws with 8.7mm ID spacers for top mounting holes. Use M8 x 40mm screws with 8.7mm ID spacers for bottom mounting holes 11 If screw gets less than 3 threads of engagement, then try the next longer length screw. If all longer lengths have been tried, and there is still less than 3 threads of engagement, then contact Customer Service for assistance. 12 If back of screen has a bumpout, then remove it, or contact Customer Service for 15.9mm tall spacers and M5x40mm screws (both are not included ). Stack the spacers with 12.7mm tall spacers that come with the mount. 13 Each top mounting hole requires stacking an 8.7mm ID spacer with a 15.9mm tall spacer ( not included ) and an M8x40mm screw. Bottom threaded holes require 15.9mm tall spacers ( not included ) and M8x25mm screws. 14 Remove all accessories, such as the D-Box, from the back of the screen. If you want to attach these accessories directly to the screen, then call Customer Service for a dedicated mount or mount accessory. 15 If you get less than 4 full threads of engagement, then contact Customer Service for M4x16mm screws (not included ) 16 If you get less than 4 full threads of engagement, then contact Customer Service for M5x16mm screws (not included ) 17 If you get less than 3 full threads of engagement, then contact Customer Service for M6x16mm screws (not included ) 18 If you get less than 3 full threads of engagement, then contact Customer Service for M8x30mm screws (not included ) 19 Top mounting holes require these fasteners, which are not included : M4x20mm, 6.4mm tall spacer, and M4 large OD washer. Place them in this order: bracket to washer to spacer to screen. 20 No Security. Requires (4) 1/4-20x1/2" screws and (4) 1/4-20 hexnuts (not included ). Refer to Bobcat instruction for removing the Mounting Plate from the back of the screen. Attach the mounting brackets to the Bobcat Mounting Plate using the 1/4-20 screws and hexnuts, then install that back onto screen. For security option, contact Customer Service for a dedicated mount. 21 If any mounting hole lies in a dimple, then place a 3.2mm thick washer ( not included ) in the dimple. 22 If any mounting hole lies in a dimple, then place an M5 flat washer (not included ) in the dimple. 50" screens require 2 more M5x12 screws. 23 Requires stacking 31.8mm tall spacers ( not included ) and 12.7mm tall spacers 24 Requires M4x35mm screws and 19.1mm tall spacers (both are not included ). Remove the cable cover from the back of the screen first. Shift the brackets down so that they are out of view when looking down from the front of the screen. 90 Hardware specifications are not currently available. Please contact Customer Service at 1-800888-6024 and ask for technical support to assist in the determination of your specific hardware configuration. 91 May require deep brackets.

14 of 14

ISSUED: 01-12-06 SHEET #: 202-9084-27 09-30-09
4900 Industry Drive Central Point, OR 97502 (800) 888-6024 or (541) 779-3763 Fax: (541) 779-0829 www.ergoindemand.com