Use of substitute replacement parts, which do not have the same, specified safety characteristics may create shock, fire, or other hazards.
17" LCD Color Monitor 1. Monitor Specifications
Items Driving system Type Size Pixel pitch LCD Panel Viewable angle Response time (type) Contrast Ratio White Luminance Sync. Type Input H-Frequency V-Frequency ON Mode Power Consumption Descriptions TFT Color LCD CLAA170EA08 43.2cm(17.0")
0.264mm(H) x 0.264mm(V) 140 (H) 130 (V) (CR10)

OFF Mode Dot Clock

135MHz @75Hz VESA DDC2BTM 100~240VAC,47~63Hz 4
Operating Temp: 5C to 35C Storage Temp: -20C to 60C
Max. Resolution Plug & Play

Power Source

Environmental

Considerations

Operating Humidity: 10% to 85%
H/V TTL 30kHz 80kHz 55-75Hz 45W 2W

500:1 300cd/m2

17" LCD Color Monitor 2. LCD Monitor Description

control logic and DDC.

The LCD monitor will contain a power board and a key board which house the flat panel control logic, brightness The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage.

Monitor Block Diagram

CCFL Drive.

Flat Panel and

Key board

100V-240V

HOST Computer
Power board (Include: adapter, inverter)

Main board

RS232 Connector For white balance adjustment in factory Video signal, DDC

CCFL backlight

17" LCD Color Monitor 3. Operating Instructions

3.1 General Instructions

Press the power button to turn the monitor on or off. The control buttons are located in the front of the monitor. By changing these settings, the picture can be adjusted to your personal preferences. The power cord should be connected. Connect the video cable from the monitor to the video card. Press the power button to turn on the monitor, the power indicator will light up.

3.2 Control Buttons

Power Button: Press this button to turn the monitor ON or OFF. Power Indicator: Green Power On mode. Off mode. Orange
Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Brightness /Contrast Adjust OSD status. Brightness : Adjust brightness or function adjust. Contrast : Adjust contrast or function adjust. Auto Adjust button / Exit:
2. When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus. OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is off and then press power button to turn the monitor on.

1. 3. MENU / ENTER Power Button/ LED 2. 4. 5. Auto Adjust button / Exit 6
1. When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu).

/ Contrast / Brightness

MENU / ENTER :
3.3 Adjusting the Picture

Adjustment steps:

Press the MENU-button to activate the OSD window. Press or to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press or again to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it. Press or to change the settings of the selected function. To exit and save, select the exit function. If you want to adjust any other function, repeat steps 2-3.
OSD TABLE: Main Menu Item Main Menu Icon Sub Menu Item Contrast Luminance Brightness Sub Menu
Description Backlight Adjustment Horizontal-Line noise Vertical-Line noise. the picture. picture. from EEPROM. from EEPROM. from EEPROM. 7
Adjust Range 0-100 Reset Value Recall Cool Contrast Value Recall Cool Brightness Do Auto Config Contrast from Digital-register. 0-100 Adjust Picture Phase to reduce 0-100 Adjust picture Clock to reduce 0-100 Do Auto Config Adjust the horizontal position of 0-100 Do Auto Config Adjust the vertical position of the 0-100 Do Auto Config The Color Temperature will be set to Cool. N/A The User R/G/B N/A value (default is 100) will not be 0-100 Modified by Reset function. Recall Warm Color Temperature N/A Recall Cool Color Temperature Recall sRGB Color Temperature Red Gain from Digital-register.

Image Setup

Position

Color Temp.

Focus Clock H. Position V. Position Warm N/A Cool N/A sRGB N/A User / Red
User / Green User / Blue Yes Green Gain Digital-register. 0-100
Blue Gain from Digital-register. Auto Adjust the H/V Position, Focus and Clock of picture. Do not execute Auto Config, return to main menu. Adjust the horizontal position of the OSD. Adjust the vertical position of the OSD.
Auto Config (Analog-Onl y Model)

H. Position

OSD Setup

V. Position OSD Timeout

0-100 10-120 N/A N/A N/A N/A N/A

Adjust the OSD timeout.

Language

Set OSD language

Information

main menu. Exit OSD 8

Show the resolution, H/V current input timing.
frequency and input port of
Clear each old status of Auto-configuration.
Do not execute reset, return to
The Language will be set to English. N/A N/A N/A N/A
17" LCD Color Monitor 4. Input/Output Specification
4.1 Input Signal Connector
Pin No. 1. 2. 3. 4. 5. 6. 7. 8. Description Red Video Green Video Blue Video TXD Ground Red Ground Green Ground Blue Ground VGA connector layout Pin No. 9. 10. 11. 12. 13. 14. 15. Description +5V Detect Cable RXD DDC-Serial Data H-Sync V-Sync

4.2 Factory Preset Display Modes
4.3 Power Supply Requirements
A/C Line voltage range A/C Line frequency range Peak surge current Leakage current Power line surge DC output Voltage
100 V ~ 240 V 50 3Hz, 60 3Hz < 55A peak at 240 VAC and cold starting < 3.5mA No advance effects (no loss of information or defect) with a maximum of 1 half-wave missing per second 12VDC 5 9

DDC-Serial Clock

4.4 Panel Specification

4.4.1 General Features

CLAA170EA08 is 17.0 color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module composed of LCD panel, driver ICs, control circuit and backlight. By applying 6 bit digital data, 1280 1024, 26.2M-color images are displayed on the 17.0 diagonal screen. Input power voltage is 12.0V for LCD driving. Inverter for backlight is not included in this module. General specification are summarized in the following table.
4.4.2 Optical Characteristics
4.4.3 Electrical Characteristics
17" LCD Color Monitor 5. Block Diagram

5.1 Software Flow Chat

10 Y N 12 Y N 19 Y 13

9 N Y 15 Y 17 N N 16

1) MCU initialize. 2) Is the EPROM blank? 3) Program the EPROM by default values. 4) Get the PWM value of brightness from EPROM. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode. 9) Save the power key status into EPROM. Scalar initializes. 10) In standby mode? 11) Update the lifetime of back light. 12) Check the analog port, are there any signals coming? 13) Does the scalar send out an interrupt request? 14) Wake up the scalar. 15) Are there any signals coming from analog port? disappear. 18) Process the OSD display. Turn on the LED and set it to green color.
16) Display "No connection Check Signal Cable" message. And go into standby mode after the message 17) Program the scalar to be able to show the coming mode. 19) Read the keyboard. Is the power key pressed?
5.2 Electrical Block Diagram

5.2.1 Main Board

Crystal 20MHZ (X402)
Crystal 14.31818MHZ (X401)
Panel Interface (CN101, CN102)

(U402)

Connector (CN404) DB15_SDA, DB15_SCL EEPROM M24C02 (U405)
OSD Control Interface (CN403)

(U401) H sync V sync RGB

EEPROM AT24C16N (U403)

MCU W78E65P-40

Scalar IC TSU17AK

(Include ADC, OSD)

5.2.2 Inverter/Power Board

AC input

EMI filter
Bridge Rectifier and Filter

Transformer

Rectifier diodes

Start Circuit: R906R907

5V CN102

Output Lamp Circuit

Feedback Circuit

PWM Control IC

MOSFET Q203Q204

ON/OFF Control

Over Voltage Protect

Feedback Circuit 12V

ON/OFF
17" LCD Color Monitor 6. Schematic

6.1 Main Board

AOC LM760

.w jel.ne t

6.2 Power Board
NRNTCR TO R906 1M 1/4W R904 C906 1M 1/4W 0.0015uF/2KV R903 100K 2W D901 FR5 R1/16W 9 + R1/2W C920 0.001uF/500V F902 FUSE L903 + C922 1000uF/16V C924 470uF/16V C928 0.1uF BD901 2KBP06M 3 + D910 31DQ10
TO INVERTER CN102 FB903 BEAD 12V GND

C905 100uF/400V

O 7,8 R922 C1/4W 0.001uF/500V 7,8 D912 31DQ06 L904 + + 10,11 C925 1000uF/16V C926 470uF/16V R1/4W ZD902 HZ12B2 ZD903 HZ5C1 IC902 R931 1K 1/16W R927 1K 1/10W 1 PC123FY2 4P 2 C936 0.1uF R929 3.9 1/16W R924 33K 1/10W R925 3.6K 1/10W C935 0.01uF R928 1K 1/10W R926 24K 1/10W CNPHONEJACK Size B Date:

ZD904 SML4737A/1

C903 0.47uF/250V

R907 1M 1/4W

R905 470K 1/4W D902 PS102R +
C913 0.001uF/160V L902 D904 1N4148
GND GND 5V 5VA DIM ON/OFF

C908 0.1uF

C907 10uF

FB902 BEAD

C900 0.001uF/160V 1 4
POWER X'FMR IC901 LDS7552 R916 100K 1/10W R1/4W

C927 0.1uF

D905 1N4148

Q903 2SK2996

C904 0.47uF/250V R901 1M 1/16W R902 1M 1/16W

CN902 SW_ON/OFF GND NC

6 C912 330pF FB901 R912 1K 1/4W BEAD 2

C913 0.0047uF/250V

D906 1N4148
R915 10K 1/16W ZD905 RLZ20B R914 NC
R1/4W F901 FUSE C901 C902 0.001uF/160V 0.001uF/160V IC904 H431BA

R910 82K 1/10W

2 CN901 SOCKET
C910 1uF/25V R911 100K 1/10W IC903 HTL431

C911 0.001uF

R918 20K 1/4W

R919 0.39 2W

CNINR GND INL

CONN <Title>

Document Number Monday, July 04, 2005 Sheet 1 of 3 Rev 1
TP1 HVO 1 TP3 HVL 1 TP4 HVL 1

C215 22pF/6KV

Q203 +12V + C201 + C223 150uF/25V 150uF/25V C202 0.1uF/25V Q202 DTA144WKA R243 1K 1/4W C225 1uF/25V R214 2.2K 1/16W Q205 MPS3904 R1/16W R212 3.9K SI4431DY-T5
D201 SR24 D203 RLZ11B R224 1.5K R225 1.5K R226 1.5K 1/4W R227 1.5K 1/4W 5 PTR220 15K C213 0.22uF/160V 2 3,R222 12K POWER X'FMR R232 1K Q209 2SC5706 Q210 2SC3 R240 51K D207 1N4148 C221 0.47uF/63V R238 12K C219 1uF/25V RTP2 HVO L202 L 1 D202 SR24 D204 RLZ11B R228 1.5K R229 1.5K R230 1.5K R231 1.5K 5 PTC214 0.22uF/160V 3,1 Q211 2SCQ212 2SC5706 POWER X'FMR 7 R233 1K R221 15K R223 12K R241 51K D208 1N4148 C222 0.47uF/63V R239 12K C220 1uF/25V R237 620

L201 L

C216 22pF/6KV

NO/OFF RK DIM R202 10K

Q201 DTC144WKA

C211 1uF/25V

RR208 4.7K 1/16W R205 47K C209 1uF/25V R210 15K

2 Q207 MPS3906 3

C203 1uF/25V

D209 1N4148

D205 1N4148

C205 0.1uF

TP5 HVL

TP6 HVL

C207 33uF

R207 NC

C204 0.1uF Q204 U201 TL1451ACNSR

C217 22pF/6KV

C206 0.1uF R206 47K

C224 1uF/25V

R215 2.2K 1/16W

R213 3.9K

SI4431DY-T1

C218 22pF/6KV

C208 330pF R203 10K
C210 1uF/25V R204 10K R209 4.7K 1/16W

R244 1K 1/4W

MPS3904

R1/16W

1uF/25V

R219 100

Q208 MPS3906

D210 1N4148

D206 1N4148

R211 15K

17" LCD Color Monitor 7. PCB Layout

7.1 Main Board

7.2 Power Board

7.3 Key Board

17" LCD Color Monitor 8. Maintainability
8.1 Equipments and Tools Requirement
1. 2. 3. 4. 5. 6. 7. 8. Voltmeter. Oscilloscope. Pattern Generator. DDC Tool with an IBM Compatible Computer. Alignment Tool. LCD Color Analyzer. Service Manual. User Manual.

8.2.1 Main Board

No Power No power
Press power key and look if the picture is normal NG
the AC of 100-240 is normal OK Measure U701 PIN2=1.8V U702 PIN2=3.3V OK X401 and X402 oscillate waveforms are normal OK Replace U402 NG Replace U401 30
Please reinsert and make sure
NG Reinsert or check the Adapter/Inverter section NG Check CN701 or replace U701, U702 NG Replace X401, X402

8.2 Trouble Shooting

No Picture (LED orange)

No picture

The button if under control
X402 oscillate waveform is normal OK

Replace X402

Measure U701 PIN2=1.8V U702 PIN2=3.3V

U402 is normal OK

Replace U402 OK NG
X401 oscillate waveform is normal NG

Check HS/VS from CN404 is normal OK NG Replace U401 31

Replace X401

Replace U701, U702
Check Correspondent component

Check reset circuit of

White Screen

White screen

Measure Q704 base is high level? Measure C104 + =12V
X402 oscillate waveform is normal
Check Q704, Q703 are broken or CN101 solder?
Check reset circuit of U402 is normal
Check Correspondent component.

OK Replace PANEL

Replace U402

8.2.2 Key Board

OSD is unstable or not working
Is Keypad Board connecting normally? Y Is Button Switch normally? Y

Connect Keypad Board

N Is Keypad Board Normally? Y Check Main Board

Replace Keypad Board

Replace Button Switch

8.2.3 Power Board

Check to CN102 pin12 = 12V NG OK NG Check the voltage of C905(+) NG OK Check start voltage for the pin3 of IC901 NG OK Check Interface board
Check AC line volt 120V or 220V

Check R906, R907, IC901

Check the auxiliary voltage is smaller than 20V
Check D910, D912, IC902, IC903 34
1) Check IC902, IC903, ZD901 2) Check Q901, Q902OVP circuit
Change F901; check BD901, Q903, and IC901

W / LED, No Backlight

Check CN102 pin12 =12V NG OK Check ON/OFF signal NG OK Check U201 pin9=12V NG OK Check the pin1 of U201 have saw tooth wave NG OK Check Interface board Check adapter or MB

Change Q201 or Q202

Check D201/D202 (-) have the output of square wave at short time.
NG OK NG OK Check the output of PT201/ PT202 NG OK Check connecter & lamp 35
Check the resonant wave of pin2 & pin5 for PT201/ PT202
Change U201 Check Q203/Q209/Q210/D201/ Q204/Q211/Q212/D202 Check Q209/Q210/C213/ Q211/Q212/C214 Change PT201/ PT202
17" LCD Color Monitor 9. White- Balance, Luminance Adjustment
1. How to do the Chroma-7120 MEM. Channel setting A. Reference to chroma 7120 user guide B. Use SC key and NEXT key to modify x, y, Y value and use ID key to modify the TEXT description Following is the procedure to do white-balance adjust 2. Setting the color temp. you want A. MEM.CHANNEL 3 (7800K color): 7800K color temp. parameter is x = 296 20, y = 311 20, Y = 180 cd/m2 , B. MEM.CHANNEL 4 (6500K color):
Approximately 30 minutes should be allowed for warm up before proceeding White-Balance adjustment.
3. Into factory mode of LM760S OSD will be at the left top of the panel. 4. Bias adjustment: Set the Contrast 5. Gain adjustment: Move cursor to -F- and press MENU key A. Adjust C2 (7800K) color-temperature to 50; Adjust the Brightness to 80.

Turn on power, press the MENU button, pull out the power cord, and then plug the power cord. Then the factory
1. Switch the Chroma-7120 to RGB-Mode (with press MODE button) 2. Switch the MEM. Channel to Channel 3 (with up or down arrow on chroma 7120) 3. The LCD-indicator on chroma 7120 will show x = 296 20, y = 311 20, Y =180 cd/m2 4. Adjust the RED of color1 on factory window until chroma 7120 indicator reached the value R=100 5. Adjust the GREEN of color1 on factory window until chroma 7120 indicator reached the value G=100 6. Adjust the BLUE of color1 on factory window until chroma 7120 indicator reached the value B=100 7. Repeat above procedure (item 4,5,6) until chroma 7120 RGB value meet the tolerance =1002 B. Adjust C1 (6500K) color-temperature
1. Switch the chroma-7120 to RGB-Mode (with press MODE button) 2. Switch the MEM.channel to Channel 4(with up or down arrow on chroma 7120) 3. The LCD-indicator on chroma 7120 will show x = 313 20, y = 329 20, Y = 180 cd/m2 4. Adjust the RED of color3 on factory window until chroma 7120 indicator reached the value R=100 5. Adjust the GREEN of color3 on factory window until chroma 7120 indicator reachedthe value G=100 6. Adjust the BLUE of color3 on factory window until chroma 7120 indicator reached the value B=100 7. Repeat above procedure (item 4,5,6) until chroma 7120 RGB value meet the tolerance =1002
C. Turn the Power-button off to quit from factory mode.
6500K color temp. parameter is x = 31320, y = 329 20, Y =180 cd/m2
17" LCD Color Monitor 10. Check List
Check if white-balance is within the specs after replacing Main board and panel, then re-writing DDC is necessary.
10.1 The White-Balance Value for Each Common Color Temperature:
6500 K: (warm color) x = 31320; y = 32920; 7800 K: (cool color) x = 29620; y = 31120; Remark: The value of Y should be confirmed according to different customers. If Customer is AOC so that its required to be larger than 170cd/cm2 (Center). The exact brightness values are confirmed by the checking-regulations of different customers and different models.
10.2 STEPSOF White-Balance Adjustment For LCD:( example for 17 AOC LCD)
white screen mode. First press the Reset key in the menu to recover factory set as following.
3. Set Chroma2325 at round-windows mode and make the detecting-head of Chroma7120 aim at the cross in the middle, the distance between the detecting-head and the cross is 20cm. white-balance value is within the specs. Please follow the steps below to adjust if it is beyond the specs. See the following pictures. 4. Set Chroma2325BGA265Ato be T1441280*1024/60HZand P105 of full white screen. Test if the

5. Cut the power. Then press MENU key and supply power at the same time to enter into the factory mode.
6. Test white-balance again after Auto Level. Adjustment with hand is necessary if it is beyond the specs just 37
SelectFthen Select AUTO LEVEL item
2. First connect the instruments together and turn on the LCD power, then warm up for 30 minutes under full
1. Required instruments: Chroma7120Chroma2325BGA265A

the same.

7. Select 7x00 item to adjust cool color-temperature and select 6x00 to adjust warm color- temperature. It can reach to the best effect through adjusting R/G/B value if it inclines to green or blue.
8. Select Exit to the upper menu after completing the adjustment. Then press POWER OFF to exit and save it. 10.3 Steps for Writing DDC:
1. Employ PC, and connect the DDC-writing instrument and the instrument that is ready for writing into DDC to the power of 12v. Connect the signal cable of the latter to D-USB or DVI of DDC-writing instrument (The data-writing of monitor needs transfer-interface) and link the DDC-writing instrument with PC through printer interface. (See the schematic picture below)
Connection of DDC-writing instrument for VGA.
2. Seek the document with the expanded name of.BAT in DDC file of this model. It appears the indication of Input Serial No.after dual-click the document to be ready for DDC-writing.
3. Input the serial number of the product (For instance: AOC LM729 is 13 bits), then press ENTER to start writing 4.Check the indication of DDC-writing program at the end. When you see the picture as the schematic picture above, the Data compare OK! means being written well and thats the end. Please check if the Manufacturer Name, Vendor Assigned Code, Monitor Name, Serial Number, Week of Manufacture, Year of Manufacture are right. It will appear Data compare error to indicate failure if the DDC-writing doesnt perform well. Please 38
check the power resource and the connection of the signal cable, then return to step 3 by pressing ENTER and re-do it. 5.You can exit the program by pressing Ctrl plus C, then cut the signal cable and the power. 6.The following picture is taking Acer AL1721 EDID for example.

Notes:

1Make sure the system time of PC is in accordance with the real time before writing.
the serial number of the BARCORD of this model. 3Data DDC-writing needs a transfer interface. InstructionDDC-writing needs 4 files: 1. Barcode.txt WR.bat
2. 3. *.EXE (DDC-writing program) perform DDC-writing) 4. w.dat 39
2The schematic picture is just as an example for description, the exact content of the DDC is dependent on

(Supply Barcode length and flow number)
(Group order file for cycling utilization of *EXE, and dual-click this file when
The content with 128 bits of DDC
17" LCD Color Monitor 11. Monitor Exploded View
17" LCD Color Monitor 12. BOM List

T780KC4HK4A1NE

Location Part No. CBPC782KC4E9 KEPC782KDAP PWPC1742CPE1 15G15G6208 L 1 15G6208 R 1 26G 40G 17N615 4A 40G 457786 3A 41G 68615 4B 41G780061513B 41G780061532C 44G44G44G44G3761615 2B 50G 50G 52G 52G Description CONVERSION BOARD KEY BOARD POWER BOARD BRACKET PANEL-BKT-L PANEL-BKT-R BARCODE

TCO99 LABEL TCO'99 CARD

SA CENTER LIST EVA WASHER EPS(L)
52G 1207 A 52G 52G 1211 A 1211 B 52G52G85G89G 715CAA D2 89G176J 89G176J E089A 89G402A15N IS 95GM1G CR3 M1G 47 CR3 M1G 47 CR3 M1GCR3 M1GCR3 Q1G CR3 41
TAPE AL TAPE MYLAR MYLAR FFCM FFC SCREW SCREW
EPS(R) CARTON HANDLE1 HANDLE2 MIDDLE TAPE FOR CARTON SMALL TAPE ALUMINIUM TAPE L705-E SHIELDING SIGNAL CABLE POWER CORD WIRE HARNESS SCREW M3X4 SCREW 3X6mm SCREW M3x6 SCREW 3X8mm

INPUT NOT SUPPORT CARD

ID LABEL
705L780KF750GLC70AH41G700N61595C H45G 2H H45G H H45G H AIC782KC4E9 CN701 CN403 33G33G40G 457624 1B 40G 45762412B C701 C706 CN404 X401 X402 CN102 CN101 U401 U702 U701 U404 U402 U403 67G215B101 4H 67G215B101 4H 88G 35315F H 93G 93G H 33G33G56G 56G 56G 56G 56G1125137CEM BEZEL ASS'Y CPT 17"020 PANEL MANUAL PE BAG FOR MONITOR
PE BAG FOR BASE/MANUAL PE BAG FOR BASE/MANUAL MAIN BOARD WAFER 2*6P 2.0MM R/A WAFER 16PIN 2.0mm DIP CPU LABEL CBPC LABEL
EC 100UF 25V LTR101M1EE EC 100UF 25V LTR101M1EE
14.31818MHZ HC-49US 20MHZ/20PF/49US
56GU405 56GQ402 Q701 Q702 Q704 Q706 Q401 Q404 57G 57G 57G 57G 57G 57G 57G Q703 Q705 RP401 RP402 RP403 RP101 FB410 FB411 57G 57G 61L 61L 61L 61L 61L0603000 61L0603000 42
AIC1084-33PM AZ1117D-1.8-EI W78E65P-40
WAFER FH12-30S-0.5SH SM CONNECTOR 50P

TSU17AK PQFP-128

EM6353BZ2SP3B-2.9 SOT23
AT24C16N-10SC-2.7 M24C02-WMN6TP PMBS3904/PHILIPS-SMT(04 PMBS3904/PHILIPS-SMT(04 PMBS3904/PHILIPS-SMT(04 PMBS3904/PHILIPS-SMT(04 PMBS3904/PHILIPS-SMT(04 PMBS3906/PHILIPS-SMT(06 PMBS3906/PHILIPS-SMT(06 AO3401L SOT23 BY AOS(A1 AO3401L SOT23 BY AOS(A1 CHIP AR 8P4R 10KOHM +-5 CHIP AR 8P4R 10KOHM +-5 CHIP AR 8P4R 10KOHM +-5 CHIP AR 894R 33OHM +-5% RST SM 0603 JUMP MAX 0R RST SM 0603 JUMP MAX 0R

D-SUB 15PIN

FB412 R102 R103 R104 R105 R108 R110 R406 R710 R716 R410 R413 R414 R418 R420 R456 R458 R465 R466 R457 R459 R704 R404 R405 R408 R409 R411 R412 R423 R424 R430 R455 R461 R462 R463 R702 R705 R707 R708 R712 61L0603000 61L0603000 61L0603000 61L0603000 61L0603000 61L0603000 61L0603000 61L0603000 61L0603000 61L0603000 61L0603101 61L0603101 61L0603101 61L0603101 61L0603101 61L0603101 61L0603101 61L0603101 61L0603101 61L0603102 61L0603102 61L0603102 61L0603103 61L0603103 61L0603103 61L0603103 61L0603103 61L0603103 61L0603103 61L0603103 61L0603103 61L0603103 61L0603103 61L0603103 61L0603103 61L0603103 61L0603103 61L0603103 61L0603103 61L0603103 43
RST SM 0603 JUMP MAX 0R RST SM 0603 JUMP MAX 0R RST SM 0603 JUMP MAX 0R RST SM 0603 JUMP MAX 0R RST SM 0603 JUMP MAX 0R RST SM 0603 JUMP MAX 0R RST SM 0603 JUMP MAX 0R RST SM 0603 JUMP MAX 0R RST SM 0603 JUMP MAX 0R RST SM 0603 JUMP MAX 0R RST SM 0603 RC0603 100R RST SM 0603 RC0603 100R RST SM 0603 RC0603 100R
RST SM 0603 RC0603 100R RST SM 0603 RC0603 100R
RST SM 0603 RC0603 100R RST SM 0603 RC0603 100R RST SM 0603 RC0603 100R RST SM 0603 RC0603 1K P RST SM 0603 RC0603 1K P RST SM 0603 RC0603 1K P
CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16

RST SM 0603 RC0603 100R

R713 R714 R720 R722 R434 R435 R460 R429 R101 R445 R446 R447 R402 R440 R441 R442 R443 R444 R448 R401 R436 R437 R438 R464 R475 R701 R703 R706 R711 R717 R718 R477 R452 R453 R454 R449 R450 R451 C441 C442 61L0603103 61L0603103 61L0603104 61L0603104 61L0603121 61L0603121 61L0603222 61L0603223 61L0603330 61L0603330 61L0603330 61L0603330 61L0603391 61L0603471 61L0603471 61L0603471 61L0603471 61L0603471 61L0603471 61L0603472 61L0603472 61L0603472 61L0603472 61L0603472 61L0603472 61L0603472 61L0603472 61L0603472 61L0603472 61L0603472 61L0603472 61L0603561 61L0603680 61L0603680 61L0603680 61L0603750 61L0603750 61L0603750 65G65G44 CHIPR 10K OHM +-5% 1/16 CHIPR 10K OHM +-5% 1/16 CHIPR 100K OHM +-5% 1/1 CHIPR 100K OHM +-5% 1/1 CHIPR 120 OHM 1/16W CHIPR 120 OHM 1/16W RST SM 0603 RC0603 2K2 CHIPR 22K OHM +-5% 1/16 CHIPR 33 OHM +-5% 1/16W CHIPR 33 OHM +-5% 1/16W CHIPR 33 OHM +-5% 1/16W CHIPR 33 OHM +-5% 1/16W CHIP 390 OHM 1/16W

BAV99 BAV99 BAV99 SS14 GS1D
TZMC5V6 TZMC5V6 TZMC5V6 TZMC5V6 TZMC5V6 TZMC5V6 TZMC5V6 BAV70 SOT-23 KEY BOARD

TB160808G151

CHIP BEAD 600 OHM 0805 CHIP BEAD 600 OHM 0805 CHIP BEAD 600 OHM 0805 CHIP BEAD 600 OHM 0805 CHIP BEAD 600 OHM 0805 CHIP BEAD 600 OHM 0805 CHIP BEAD 600 OHM 0805

MAIN BOARD PCB

PIN HEADER 2*7 R/A
SW001 SW002 SW003 SW004 SW005 DP101 77G 600 1GCJ 77G 600 1GCJ 77G 600 1GCJ 77G 600 1GCJ 77G 600 1GCJ 81G 12 1F GP 715GJ001 J002 J003 J004 95G 95G 95G 95G PW1742CPE1SMT L902 PT201 PT202 CN201 CN202 CN203 CN204 S73L17426VG S80LL15T7VG S80LL15T7VG 33G8021 2D U 33G8021 2D U 33G8021 2D U 33G8021 2D U 40G 45762412B 51G IC902 IC901 Q209 Q210 Q211 Q212 R4500 TACT SWITCH TSPB-2 TACT SWITCH TSPB-2 TACT SWITCH TSPB-2 TACT SWITCH TSPB-2 TACT SWITCH TSPB-2 LED KEY BOARD PCB TINCOATEDCOPPER TINCOATEDCOPPER TINCOATEDCOPPER TINCOATEDCOPPER
POWER BOARD FOR SMT COMMON CHOKE TRANSFORMER TRANSFORMER 3.5mm WAFER 3.5mm WAFER 3.5mm WAFER 3.5mm WAFER CBPC LABEL RTV

56G 139 3A 56G 379 53

57G 57G 57G 57G 61G 2JNR901 R903 C904 C215 C216 C217 C218 C901 C902 C913 C922 C925 61G 58080 WT 61G152M63G107K474 HS6319 H H H H 65G 3J2206ET 65G 3J2206ET 65G 3J2206ET 65G 3J2206ET 65G305M2222BP 65G305M2222BP 65G306M4722BP 67G215V102 3R 67G215V102 3R 47
PC123Y22FZOF LD7552BN 2SC5706-PM-E 2SC5706-PM-E 2SC5706-PM-E 2SC5706-PM-E 0.39 OHM 5% 2W 8 OHM NCT 100KOHM 5% 2W X2 CAP 0.47UF K 275VAC 22PF 5% SL 3KV TDK 22PF 5% SL 3KV TDK 22PF 5% SL 3KV TDK 22PF 5% SL 3KV TDK 2200PF +-20% 2200PF +-20% 4700PF +-20% 400VAC LOW E.S.R 1000UF +/-20% LOW E.S.R 1000UF +/-20%
C201 C223 C924 C926 C905 L903 L904 L201 L202 T901 BD901 CN102 H1 67G215V471 3N 67G215V471 3N 67G215V471 3N 67G215V471 3N 67G305S10114H 73G H 73G H 73G 253139 YA 73G 253139 YA 80LL17T 2 TG 93G 50460502 95GJ85G705L 02 705L 15 705L 780 5702A PW1742CPE1AI U201 Q205 Q206 Q207 Q208 Q201 56G 57G 57G 57G 57G 57G 57G 760 4B 470UF/16V 470UF/16V 470UF/16V 470UF/16V 100UF +-20% 400V CHOKE COIL CHOKE COIL CHOKE COIL CHOKE COIL SRW28EC-X12HO18-D KBP206G HARNESS SHIELD
D910/D912 ASS'Y Q903 ASS'Y
Q202 Q203 Q204 R216 R217 R925 R212 R213 R929 57G 57G 61L0603221 61L0603221 61L0603362 61L0603392 61L0603392 61L0603392 R927 R928 R926 R924 R208 R209 R917 R911 61L0805102 61L0805102 61L0805242 61L0805333 61L0805472 61L0805472 61L1206100 61L1206100 3F 48

100OHM +- 5% 1/6W 100OHM +- 5% 1/6W

CFR 1K OHM+-5% 1/6W

CFR 10K OHM+-5% 1/6W
R236 R237 R234 R235 FB902 FB901 ZD902 D901 61G 60268152T 61G 60268152T 61G 60291152T 61G 60291152T 71G T 71G 93G 39 5452T 93G 6026T52T 50
2.2K 5% 1/6W 2.2K 5% 1/6W FERRITE BEAD HZ12B2-E
CFR 10K OHM+-5% 1/6W 12KOHM 5% 1/6W 12KOHM 5% 1/6W 12KOHM 5% 1/6W 12KOHM 5% 1/6W 15KOHM 5% 1/6W 15KOHM 5% 1/6W 15KOHM 5% 1/6W 15KOHM 5% 1/6W
30KOHM 5% 1/6W 47KOHM 5% 1/6W 47KOHM 5% 1/6W 51KOHM +-5% 1/6W 51KOHM +-5% 1/6W 680 OHM 5% 1/6W 680 OHM 5% 1/6W CFR 910 OHM+-5% 1/6W CFR 910 OHM+-5% 1/6W FERRITE BEAD D9X3. 5X0.

RECTIFIER DIODE FR107

D902 D205 D206 D207 D208 D209 D210 IC903 IC904 C911 C204 C205 C206 C936 C221 C222 C906 C208 C912 C908 C920 C921 C907 93G 6038P52T 93G 64 1152T 93G 64 1152T 93G 64 1152T 93G 64 1152T 93G 64 1152T 93G 64 1152T 56G T 56G T 64G700J1020AT 64G700J1040AT 64G700J1040AT 64G700J1040AT 64G700J1040AT 64G701J4740AT 64G701J4740AT 65G 2K152 1T6921 65G 44233113T 65G 444331 5T 65G 450104 7T 65G517K102 5T6213 65G517K102 5T6213 67G 2152207NT 67G 305479 7T 87G CJ A A PS102R 1N4148 DO-35 1N4148 DO-35 1N4148 DO-35 1N4148 DO-35 1N4148 DO-35 1N4148 DO-35 H431BA H431BA 1000PF 50V PEN 0.1UF 50V PEN 0.1UF 50V PEN 0.1UF 50V PEN 0.1UF 50V PEN 0.47uF 50V 0.47uF 50V
C207 CN901 95G205S354022 96G 90GD912 93G 60217 D910 93G 60250 M1GCR3 Q903 57G 724 4A 90G M1GCR3 15G33GC 33G4848 AS L 33G34G1544BAS 2B 34G1546 GM B 51
SCREW SCREW CLAMP LENS BEZEL STAND
330PJNPO 50V 330P/50V DIP 22UF/50V AC SOCKET HARNESS HEAT SINK FCH10U10G STP9NK60ZFP HEAT SINK HINGE-BKT KEY PAD

1.5NF/2KV Y5P+-10%

0.1UF +80-20% 50V Y5V
1000PF 10% Y5P 500V 1000PF 10% Y5P 500V

4.7UF 20% 50V 105

SHRINK TUBE UL/CSA

FMB29L 10A 100V SANKEN

34G1547 GM B 37GQ1G CR3 Q1GCR3 H34G0041 GM14B 2F0605100 BASE HINGE SCREW SCREW REAR COVER SCREW NUTS M6.0*P1.0

SPECIFICATIONS

Panel TFT Active Matrix LCD, Slim Cabinet VIS: 17" (43.2cm), Diagonal Hard Coating (3H), Anti-glare Treatment Basic 0.264mm x 0.264mm Design Line Pixel / Dot Pitch Viewable Image Size (Diagonal) 17 Display Area Brightness Contrast Ratio Typ. Response Time (tr+tf) Viewing Angle Compatibility Scanning Frequency Pixel Frequency Maximum Resolution Recommended Resolution Resolution Supported 338mm x 270mm 300 cd/m (typ) 700:1 8ms Horizontal: Vertical: 150 Degrees 130 Degrees VESA, SXGA, XGA, SVGA, VGA MacEquipped With VGA Port Horizontal: Vertical: 135 MHz 1280x1024@75Hz 1280x1024@60Hz 640x350@70Hz, 740x400@70Hz, 640x480@60/75Hz, 800x600@60/75Hz, 1024x768@60/70/75Hz, 1280x1024@60/75Hz 16M Video: 0.7Vp-p, RGB analogue Separate Sync: TTL Level H/V Sync: Positive / Negative RGB Signal: 15-pin D-sub Male (Attached) Power: 3-pin Plug (CEE22) Power Input: Universal 100~240VAC, 50/60Hz 45Watts (Max) DDC1/2B Yes Stand-by Power, Auto Config Brightness, Contrast, Focus, Clock, H/V Position, Language, Colour Temperature (C1, C2), Reset, Exit, RGB English, German, French, Spanish, Italian 2 x 1.5Watt Volume, Earphone Output TC099 UL, CSA, FCC, TUV/GS, CE, ISO 13406-2, WindowsXP Logo VESA 75mm Wall Mountable*, Kensington Security Slot Monitor: 380x86x385 mm Carton: 435x134x456 mm Net: Gross: 4.0 Kg 5.0 Kg 20" 988 pcs 30K~80KHz 55~75 Hz

I NEED

Colours Signal Input

Connectors

Power Source Power Consumption Plug & Play EPA ENERGY STAR User Control Function OSD Languages Speaker Emissions Standard Regulations Other Features Dimensions (WxHxD mm) Weight Loading Qty w/pallet Warranty

40" 2052 pcs

3-year limited warranty
* Wall mount arm & bracket not included.
Note: Specifications are subject to change without notice.

www.AOCdisplay.com

c 2006 AOC Monitors. All rights reserved. AOC is a registered trademark. All other trademarks are the property of their respective owners. Sales: sales@aocmonitor-anz.com