A U T O

D5036_1
2. The LIGHT soft key indicates the brightness level, use the trackpad (up or down) to increase or decrease the setting. You can press and hold the trackpad to change the setting more rapidly. The brightness level is adjusted as you change the setting. 3. Press ENTER to return to the default screen, with the new brightness level. To set the screen brightness to 100%: Press and hold the MULTI key for one second. The brightness is increased to 100%. Note: During night-time use, the brightness may be set very low, when subsequently operated during the day it may not be apparent that the display is on; press MULTI, followed by the second soft key from the left, then use the trackpad to increase brightness. Alternatively, press and hold MULTI for one second to set the brightness to 100%.
2.3 Controlling the Display
You control the display using the cursor and control keys. You start all operations from the default screen, that is the default soft keys are displayed: Chart
ROUTE GOTO SCREEN FIND SHIP

D4160-1

When you have completed an action using the soft keys, press ENTER or CLEAR to return to the default screen; you may need to press ENTER or CLEAR several times to back-track through the soft key hierarchy. Note: If you have set up your system so that the default soft keys are not displayed all the time, press any soft key to display the labels. The remainder of this section describes how to select the mode of operation and switch half-screen windows on/off. The following sections describe how to set up the display for the Radar and for the Chart. The controls are summarized in the fold-out illustration on pages 2-11 and 2-12.
Selecting the Mode of Operation
You use the DISPLAY key to select the full-screen mode. If the data is available on your system, the following modes (described on Operating Modes on page 1-5) can be selected: Radar Chart Data log The DISPLAY key also accesses the soft keys for the half-screen window options.

Controlling the Display

To change the mode, press the DISPLAY key to show the DISPLAY pop-up, then press again to cycle through the modes available, shown in the Figure 2-5.
Selecting the Mode of Operation Figure 2-5: Using the DISPLAY Key The selected mode is shown by an icon with a red border and the mode is displayed on the screen. The associated half-screen window soft keys are also displayed. When the required mode is shown, press ENTER or CLEAR. The default soft keys are displayed. The selected mode is shown full-screen; in Radar and Chart mode you can switch on half-screen windows for additional display, as described in the following section. If you press DISPLAY again, the pop-up and soft keys for the current mode are shown.
Selecting a Half-Screen Window for Display

Cancel a Target

To cancel a target using the context-sensitive cursor: 1. Move the cursor over the target, the following soft keys are displayed.
CANCEL TARGET MARPA BOX OFF ON

D4119_1

CANCEL TARGET
2. Press the CANCEL TARGET soft key to cancel target tracking and remove the symbol from the display. The default soft keys are displayed.

MARPA LIST

To cancel a target from the database list. 1. Press the default soft key MARPA to display the MARPA soft keys. 2. Press the MARPA LIST soft key, the database list is displayed. 3. Use the trackpad to select a target, then press the CANCEL TARGET soft key to remove the selected target. 4. Press CLEAR to remove the database list. Using MARPA

View Target Data

You can toggle the MARPA data box on/off using the MARPA BOX ON/OFF soft key. This box displays the data for one MARPA target. You can select the target using the context sensitive cursor or the database list. Alternatively, if you display the data box when no target is selected, data is displayed for the last target that had the data box displayed unless a new target has been acquired, then the new target data is displayed. To view (or hide) target data using the context sensitive cursor: 1. Move the cursor over the target for which you require data. The letters MARPA and the following soft keys are displayed.

MARPA BOX OFF ON

2. Press the MARPA BOX ON/OFF soft key to toggle the data box on/off for the selected target.The target data box is displayed and the associated target symbol is identified by a circle drawn around it. The default soft keys are displayed when you move the cursor away from the target. Note: When you select ON, if the data box was already displayed for another target, it is updated for the selected target.

MARPA 1

BRG 84M RNG 1.48nm CRS 110M SPD 0.0kts CPA 1.48nm TCPA PASSED

D4117_1

Figure 3-15: MARPA Target Data Box To view (or hide) target data using the default soft keys: 1. Press MARPA to display the MARPA soft keys.
2. Press the MARPA BOX ON/OFF soft key to toggle the data box on. The target data box is displayed and the associated target symbol is identified by a circle drawn around it. The default soft keys are displayed.

Tide Data

The symbol indicates tide height data is available for that position on the chart. When you select the tide height option, a graph of predictions for maximum and minimum tide heights is displayed, data for sunrise and sunset is also provided as illustrated Figure 5-3.
Note: The predictions available are sufficiently accurate under moderate weather conditions, for the coastal areas served by the reference station, to be used for navigation planning. However, certain weather fronts and storms can alter tidal patterns and influence predicted times and heights. The cursor, represented by a dotted vertical line on the graph, is used to select a time for which the tide height is displayed. You can use the soft keys and trackpad to change the date for which tide information is shown.
4.61 3.96 3.31 2.66 2.01 1.36 0.2 4
CSR 5049^05W POS 00118^00W

BRG 304T RNG 27.70nm

CALSHOT CASTLE
Displaying Object Information
CURSOR TIME 13:30 HEIGHT 4.06m SUNRISE/SUNSET TWILIGHT 0646 SUNRISE 0807 SUNSET 1611 TWILIGHT 1732
SELECTED DATE 2/01/1998 HIGH/LOW WATER HIGH 0220 4.22m LOW 0640 0.88m HIGH 1400 4.10m LOW 1900 0.76m

SET DATE

PREV. DAY

NEXT DAY

D4270-1

Figure 5-3:

To select a time, use the trackpad to move the cursor to the required time. To change the day press PREV. DAY, DAY or TODAY, as required. Alternatively, press SET DAY; to change date, use the trackpad to move the cursor left/right to select the character and up/down to increase/decrease the value. The graph and tide data will be updated accordingly.

Nearest

To obtain the information for the nearest port facility: 1. Move the cursor to the required position this can be anywhere on the chart and may be over an object then press ENTER to display the object information pop-up. 2. Press the NEAREST soft key. The port facility symbols are displayed. 3. Use the trackpad to highlight the required facility, then press ENTER. 4. The nearest ports providing that facility are listed with distance and bearing to the port. If you highlight a port name then press ENTER, details for that facility are displayed. Typical port data is shown in Figure 5-4. Press CLEAR to return to the port list. Press CLEAR to return to the facility symbols. 5. Press CLEAR to return to the default display.

D4255_1

Figure 5-4:
Nearest Port - Typical Data
5.3 Working with Waypoints
The HSB Series Chartplotter enables you to place up to 998 waypoints: a waypoint is a position entered on a chart as a reference, or as a place to go to. All waypoints placed on the chartplotter or are stored in a waypoint database list which includes symbol, position, bearing, range and additional data. All waypoints in the database are displayed on the screen, unless you set waypoint display off in the Chart Set Up menu, as described in Chapter 7. You can select a waypoint, either on-screen or from the list, for editing. The waypoint is usually placed at the cursor position, you can also place a waypoint at the vessels current position (this is sometimes known as an event mark); a waypoint at the vessel position includes additional information (if available) on the depth and temperature when it was placed. Both types of waypoint can be included in a route. You can place waypoints, using simulator mode, before you install the chartplotter on your vessel. Note: Radar marks may also be displayed on the screen if your chartplotter is a combined radar/chartplotter or is part of an integrated system; these are screen annotations - you cannot go to marks, nor can they be included in routes. When you place a new waypoint, it is displayed using the default symbol of a cross. The waypoint is added to the waypoint list and tagged with the next available number. You can use the edit functions to change the symbol and name. When the cursor is positioned over a waypoint, the waypoint bearing and range are displayed. Waypoints in the current route are available on other SeaTalk instruments that support current route transfer, for example, another HSB Series Chartplotter or ST80 Masterview. You can also transfer waypoints between the chartplotter and other NMEA or SeaTalk instruments using the Waypoint Transfer functions. This section explains how to perform the following tasks using the on-screen cursor and the waypoint list: Placing a Waypoint Selecting a Waypoint Displaying Waypoint data Editing a Waypoint (symbol, name & position) Erasing a Waypoint Moving a Waypoint

5. To edit the waypoint position, press the EDIT WAYPOINT soft key, followed by POSITION. The Waypoint Position pop-up is displayed. Use the soft keys to select LAT, LON, BRG or RNG. Use the trackpad to edit the value: Use the left or right side of the trackpad to move the cursor to the character you wish to change. Use the top or bottom of the trackpad to scroll through the characters. Adjust each parameter until the waypoint position is correct. When you have finished editing the position, press ENTER to save the position or CLEAR to cancel the operation. Press ENTER or CLEAR again, the Waypoint Position window is removed from the screen and the default soft keys are displayed.

Erasing a Waypoint

You cannot erase the target waypoint or waypoints that are used in routes. However, you can remove a waypoint from the current route - see Editing a Route on page 5-21. If you try to erase a waypoint that is used in a saved route you are warned WAYPOINT IS USED IN A ROUTE & CANNOT BE DELETED
To delete a waypoint using the cursor: 1. Move the cursor over the waypoint, until the letters WPT are displayed. The waypoint soft keys are displayed. 2. Press the ERASE WAYPOINT soft key. The waypoint is removed from the screen and the Waypoint List is updated. Note: If you have stopped a GOTO (see Stop Follow or Stop Goto on page 5-27), the target waypoint remains displayed as a target; you need to use the CLEAR GOTO soft key before you can erase the waypoint using the cursor.

ERASE WAYPOINT

To delete a waypoint using the waypoint list: 1. Select the waypoint from the waypoint list as previously described. The waypoint list soft keys are displayed. 2. Press the EDIT WAYPOINT soft key, followed by ERASE WAYPOINT. The waypoint is removed from the screen and the waypoint list is updated.

Moving a Waypoint

You can move any waypoint except the target waypoint (the waypoint you are following). You can use the Waypoint soft keys and cursor to move the selected waypoint, or you can edit the waypoint position. Moving a Waypoint CAUTION: Take care when editing waypoints as it is possible to move waypoints that are used in routes stored in the Route Database List.
To move a waypoint using the cursor: 1. Move the cursor over the waypoint, until the letters WPT are displayed. The waypoint soft keys are displayed. 2. Press MOVE WAYPOINT, the cursor changes to a four-headed arrow. 3. Move the cursor to the required waypoint position. Press ENTER to set the position and return to normal cursor control. Press CLEAR to cancel the operation.

Creating a New Route
Creating a New Route Note: If there is a current route, it is cleared when you select MAKE ROUTE. If you are following the current route you are prompted to STOP FOLLOW. Press the YES soft key to continue, or NO to abandon route creation. If the route has not been saved you are prompted to save it. The chart scenario Make and Follow a Route on page 2-28 provides a simple example of how to create a route. You can edit a route after you have finished making it, as described in Editing a Route on page 5-21. To make a new route by placing waypoints: Note: You can pan the chart and change the scale while placing waypoints. 1. If necessary, move the cursor to the area in which you wish to make the route, and select a suitable chart scale.
2. Press the ROUTE soft key, then press the MAKE ROUTE soft key. The make route soft keys are displayed:
PLACE WAYPOINT UNDO WAYPOINT ACCEPT ROUTE

D4170-1

PLACE WAYPOINT
3. Move the cursor to the position on the chart where you want your first waypoint to be. Press the PLACE WAYPOINT soft key. Note: You can position the cursor on an existing waypoint the text WPT indicates you are re-using the waypoint rather than placing a new one. This waypoint is included in the route when you press PLACE WAYPOINT. The waypoint appears on the screen at the cursor position. The number displayed alongside the waypoint identifies its position in the route. The new waypoint is temporarily added to the waypoint list with the first available waypoint number. The waypoints in the current route are re-numbered to identify the new positions. Note: If you Clear the route before it is Saved, the waypoint is removed.
4. Move the cursor to the next waypoint position. A dotted line connects the cursor to the last placed waypoint.
5. Press PLACE WAYPOINT again. The waypoint is placed and the dotted line changes to a solid line. If you placed the waypoint incorrectly, you can delete the last-placed waypoint by pressing the UNDO WAYPOINT soft key. 6. Repeat steps 4 and 5 until you have placed all your waypoints. You can have up to 50 waypoints in a route. 7. When you have entered all your waypoints, either: Press the ACCEPT ROUTE soft key (or ENTER) to complete the route. Your route is displayed on the screen, and is the current route, but it is not active. The first waypoint of a new route is outlined with a square, indicating that it will be the target waypoint when the route is activated. If selected, the waypoint data box is displayed for the target waypoint. You can save the route as described below. Note: The completed route is stored in the display unit, and will be re-displayed if you turn the unit off and on again. However, on an integrated system it is possible for a current route from another unit to overwrite this route; it is therefore recommended that you Save the route as described below.

Editing a Route

Once you have created a route, you can edit it by: Inserting a Waypoint into the route Adding waypoints at the end of the route Removing a Waypoint Reversing a Route Moving a Waypoint as described in Moving a Waypoint on page 5-13. Any changes you make to the route affect only the current route. The current route is always held in position 0 in the database, so you need to Save the route if you want to keep the changes.
Inserting a Waypoint into a Route
You can use the context-sensitive cursor to insert one or more waypoints in the current route. However, if the route is being followed you cannot insert a waypoint into the current leg.
To insert a new waypoint in the current route: 1. Move the cursor over the route leg into which you wish to insert a waypoint. The letters RTE and the route leg data box are displayed. The Route soft keys are displayed. 2. Press ENTER. The cursor changes to a four-way arrow, controlling a new waypoint. The waypoint is connected to the existing waypoints on either side with a dashed line. 3. Move the new waypoint to the required position, and press ENTER to drop it and return to normal cursor operation, or CLEAR to abandon the operation. The new waypoint is temporarily added to the waypoint list and named with the first available waypoint number. The waypoints in the current route are renumbered to identify the new positions. Note: If you Clear the route before it is Saved, the new waypoint is removed.

Editing a Route

ROUTE EDIT ROUTE PLACE WAYPOINT UNDO WAYPOINT ACCEPT ROUTE
Adding Waypoints at the End of the Route
To add waypoints at the end of the route: 1. Press the ROUTE soft key, followed by the EDIT ROUTE soft key. The Make Route soft keys are displayed and the cursor is connected to the last-placed waypoint with a dotted line. You can add further waypoints to the route in the same way as for a new route. 2. Move the cursor to the required location, and press PLACE WAYPOINT soft key. If you place the waypoint in the wrong position, press the UNDO WAYPOINT soft key. Note: You can UNDO waypoints in the original route, not just the new ones. 3. Place as many waypoints as required, and press the ACCEPT ROUTE soft key, the default soft keys are displayed.

Removing a Waypoint from the Route
To remove a waypoint from the current route: 1. Move the cursor over the required waypoint until the letters WPT are displayed. The waypoint soft keys are displayed. 2. Press the REMOVE WAYPOINT soft key. The waypoint is removed from the route and the route is re-numbered. Alternatively, you can remove the last waypoint from a route by pressing the UNDO WAYPOINT soft key, as described above in Adding Waypoints at the End of the Route on page 5-22.

REMOVE WAYPOINT

If the route has not been saved, the waypoint is erased. If the route has been saved, the waypoint remains on the screen.

Reversing the Route

To reverse the route, so you can Follow the route back: 1. Either press the ROUTE soft key followed by MORE, or move the cursor over the required waypoint until the letters RTE are displayed. The route soft keys are displayed. 2. Press the REVERSE ROUTE soft key. The current route is reversed on the screen. Following Routes and Going to Points
5.5 Following Routes and Going to Points
The default soft key GOTO accesses the functions to FOLLOW a route and GOTO a waypoint or cursor. When you select the target destination, the chartplotter calculates bearing, distance and cross track error; this information is passed to a helmsman or autopilot. You can also restart the cross track error (XTE) from the actual vessel position to set XTE to zero at that point.
When the chartplotter is following a route, the target destination is indicated by a square around the waypoint (or cursor marker) and a dotted line shows the intended track, from your start point or previous waypoint, to the target waypoint. This section describes the following: Follow a route either forwards, or in reverse order. Target Point Arrival Other follow route options, including joining at a selected waypoint, advancing waypoints, and restarting XTE. Go to an individual point, either an existing waypoint or the cursor. Stop and Restart Follow/Goto. An alarm is triggered when you approach a waypoint, this section describes what happens when you arrive at waypoints. Chapter 6 describes how to set the alarm. The chartplotter can also display the vessels actual track and the track can be recorded for later display. The Track function is described in the Section 5.7.

Changing the Set Up Parameters
To set the default parameters: 1. Press the MENU key to display the set up soft keys - the options available depend on the selected operating mode. Radar
SYSTEM SET UP! RADAR SET UP! MARPA SET UP!

D3640-3

2. Press the soft key for the set up you require. The requested set up menu is displayed, listing the parameters and their current settings. 3. Use the trackpad to move the selection bar up and down the list. An arrow is displayed at the top or bottom right-hand corner if you can scroll the list to display further parameters. As each line is highlighted, the soft keys are updated to show the settings available.
For parameters that have a numeric value, or more than four possible settings, a scroll list is displayed above two of the soft keys. Some parameters are controlled by a slider that is displayed above two of the soft keys. For some parameters, a soft key provides access to a sub-menu of further options. 4. Press the soft key corresponding to the desired setting or, for scroll lists, use the soft keys to scroll forwards or backwards through the list until the required setting is displayed. This setting is retained when you move the selection bar on to the next parameter in the menu list. For sliders, press the appropriate soft key repeatedly to increase or decrease the slider value in individual steps, or press and hold the key to change the setting quickly. 5. Once you have reset all the required values, press ENTER to clear the menu and return to the set up soft keys. 6. Press ENTER, MENU or CLEAR to clear the soft keys and return to the default display. Changing the Set Up Parameters You can return all the settings to their original factory settings, if required, by performing a factory reset as described in Chapter 9.
7.3 System Set Up Parameters
The following table lists the System menus and their options, shows the factory default setting, and provides a space for you to make a note of your new default setting. Each parameter is described in the following subsections. Table 7-1:

Cursor Readout

Bearing Mode This option controls whether the cursor data is shown in latitude and longitude or in range and bearing. Alternatively, you can show both types of readout, in separate boxes, or turn the cursor data box off. You can also turn the cursor readout box(es) on and off during normal operation, via the SCREEN default soft key (see Switching the Cursor Data Box On and Off on page 2-13.)
When Help is set to ON, a prompt appears when selecting a soft key or menu choice, and when using the context-sensitive cursor. The help message is cleared when an action is selected.
When the Soft Keys option is set to ON, the default soft keys are displayed if no other operation is in progress. When the Soft Keys option is set to OFF, the default soft keys are only displayed when a soft key is pressed, and they disappear if no operation is performed for 10 seconds.

Key Beep

This option controls whether or not the keys make a noise when you press them.

MOB Data

This option controls whether MOB data is based on position data, or on dead reckoning (DR). Dead reckoning normally provides a better indication of the course to an object in the water, on the assumption that your vessel and the object are both subject to the same tide and wind effects.

Menu Timeout Period

With no timeout set, menus and soft key labels remain displayed until you clear them by pressing ENTER, CLEAR or the appropriate dedicated key. If you set a value here, the menus and soft key labels will be cleared if a key has not been pressed for the specified number of seconds. This setting does not affect the default soft key labels, which are controlled by the Soft Keys option (see above).
You can set the units for speed, depth and temperature. The units you set will be used to display all data, including information received from other instruments on the system. However, the distance units do not affect the instrumented range of the radar, which is always in nautical miles.

Variation Source

The variation value is the difference between True and Magnetic direction data for heading or bearing values. The Variation Source option provides soft keys for selecting Auto or Manual variation mode, displays the current variation value for each and highlights the currently selected mode.
Auto Mode (available in systems with HSB Radar)
If you select Auto mode, the radar obtains the value of variation automatically, normally from received data. The variation value that is used depends on the data available, and is selected in the following order of priority: 1. Variation value from the same source as the heading data: If heading data is being taken from NMEA, then variation is also taken from NMEA If heading is taken from SeaTalk, then SeaTalk variation is used

D5063-1

Figure 8-3:
7 LCD Color Display Dimensions

8.5 in (217 mm)

8.1 in (205.2 mm)

7.3 in (185 mm)

11.5 in (292 mm)

3.82 in (97 mm)

11.4 in (289 mm)
6.38 in (162 mm) cable clearance

12.9 in (328 mm)

1.65 in (42 mm)

12.3 in (313 mm)

9.7 in (246 mm)
0.87 in (22.1 mm) 3.94 in (100 mm)

3.15 in (80 mm)

0.28 in (7.1 mm)

10.83 in (275 mm)

Weight: 12.65 lbs (5.75 kg) Compass Safe Distance: 39 in (1 m)

D5066-1

7.88 in (200 mm) 11.26 in (286 mm)

1.7 in (43 mm)

Figure 8-4:
10.4 LCD Color Display Dimensions

8.4 Cable Runs

Consider the following before installing the system cables: You need to attach the power cable and the scanner cable. Additional cables will be required if you are installing an integrated system. All cables should be adequately secured, protected from physical damage and protected from exposure to heat. Avoid running cables through bilges or doorways, or close to moving or hot objects. Acute bends must be avoided Where a cable passes through an exposed bulkhead or deckhead, a watertight feed-through should be used. Secure cables in place using tie-wraps or lacing twine. Coil any extra cable and tie it out of the way. You need to run the following cables: Power/NMEA Input cable, supplied with the display unit. This has a connector plug at one end for connecting the display unit, and 7 wires at the other end for connecting the power supply and optional NMEA inputs (see Section 8.8, Integrated Systems). Inter-unit cable, supplied with the scanner unit. This is Vinyl-covered and shielded, with a connector plug at one end for connecting to the display unit or extension cable. SeaTalk cable, optional, with SeaTalk connector(s) at one or both ends. HSB cable, optional. NMEA Output cable, optional, with an NMEA OUT connector at one end only.

Cable Runs

Power Cable
The HSB Series display system (i.e. with a scanner connected where applicable) is intended for use on ships DC power systems rated as follows: 12 V or 24 V systems 12 V, 24 V or 32 V systems 24 V or 32 V systems Radome Scanner System 4 kW Open Array Scanners System; RC530/kW Open Array Scanners System

Screen Functions Data Boxes
Full, half and quarter screens available dependent on function Up to six user selectable information boxes

Radar Features

Range Scales (Range Rings)p 0.125 (0.0625), 0.25 (0.125), 0.5 (0.125), 0.75 (0.25), 1.5 (0.25), 3 (0.5), 6 (1), 12 (2), 24 (4), 48 (8) or 72 (12) nnm selectable (dependent on scanner). Performance limited by the scanner type and position. Range scales can be customised Better than +/ 1.5% of the max. range scale in use, or 22 m (72 ft), whichever is the greatest. +/ 1 2xVRMs, readout nm, kyds, sm, km 2xEBLs, floating if required, resolution graduated at 10 intervals 23 m (25 yds) 23 m (25 yds) Head up, Course up or North up (selectable True or Magnetic) Relative or True Motion Interference rejection, standby/transmit modes, pulse selection, Tune, Rain, FTC, and Sea controls, with selection of manual or automatic control of gain, sea clutter and tune (Auto GSTTM) NMEA or Seatalk Lollipop symbol, WPT range, bearing, TTG or lat/lon readout 100 Mark database Manual acquisition of 10 targets, automatic tracking, dangerous target alarms, safe zone, target history, true or relative vectors Auto (SeaTalk/NMEA/Internal algorithm) or Manual 2 guard zones, selectable sensitivity level, audible alarm User selectable in split screen mode provided chart data available x2, from 0.25 nm to maximum range, in 1/4 window and full screen from 1/4 window. 66% of radius (except maximum range) Radar, Chart, CDI, BDI and Navdata Short, medium, long, off Operator selectable (0.5 nm to 3 nm ranges only) Rotation periods: 10, 20 or 30 scans Repetition periods: 3, 5, 10 or 15 minutes
Range Ring Accuracy Bearing Accuracy Variable Range Markers Electronic Bearing Lines Bearing Scale Minimum Range Range Discrimination Presentation Modes Scanner Control
Magnetic Sensor Waypoint Navigation Marks MARPA - 10.4" Display Variation Source Guard Zone Alarm Radar/Chart Synchronization Zoom Mode Off Centre Function Display Windows Wakes Target Expansion Timed TX

Chartplotter Features

Cartography Display Windows Chart Scaling Presentation Modes Waypoints C-MAP NT micro cartridges available from C-MAP Chart of the world built in Chart, Radar, Data Log, BDI, CDI, Navdata 1/64 nm (if cartographic data is available) to 4000 nm North up (selectable True or Magnetic) Head up or Course up 1000 waypoints entered via cursor, lat/lon, range and bearing from present position or at vessels position. 16 character name can be assigned HSB, current route via Seatalk, NMEA A route plan may contain up to 50 waypoints. Up to 20 routes can be stored in the units internal memory 5 tracks with up to 750 points in each can be stored in the units internal memory Programmable arrival, cross track error, anchor drift, position fix/ data loss warning, countdown timer and alarm clock Own ships position in Lat/Lon, XTE, TTG and SOG/COG selectable. Mileage scale ruler. Bearing and distance to waypoint. Bearing and distance to cursor, SeaTalk data (see interfacing section) Auto (SeaTalk/NMEA/Internal algorithm) or Manual User selectable in split screen mode provided radar/chart data available

Data HSB 6-1 Data Box 2-14, 7-4, 7-5 COG 7-4 Date 7-4 Depth 7-4 Group of Six 2-14 On/Off 2-14 Heading 7-4 List of 7-4 Log/Trip 7-4 MARPA Target 3-27 MOB 4-5, 6-6 Moving 2-14, 3-18 On/Off 3-18 Pilot 7-4 Position 7-4 Ruler 6-2, 6-3
SOG 7-4 Speed 7-4 Temperature 7-4 Tide Set/Drift 7-4 Time 7-4 VMG 7-4 Waypoint 7-4 Wind 7-4 XTE 7-4 Data Display 5-19 Chart Object 5-4 Nearest 5-7 Port 5-4, 5-5 Tide 5-4, 5-5 Route 5-15 Data from other Equipment 4-1, 6-1, 6-6, 8-29 Chart 4-1 COG 6-1 Heading 4-1, 4-5, 6-1, 6-6 HSB 4-1 Navigation Data 4-1 NMEA 4-1, 4-4, 6-1 Position 4-1, 4-5, 6-1, 6-6 Radar 6-1 SeaTalk 4-1, 4-4, 4-6, 6-1 Speed 6-6 Waypoint 4-1 Data Log Mode 1-6, 6-1, 6-9 Full Screen 2-7 Database List 1-14, 1-18 MARPA 3-27, 3-28 Route 5-13, 5-15, 5-16, 5-19 Track 5-31 Waypoint 5-8, 5-9, 5-15, 5-27 Date Data Box 7-4 Date Format 7-5, 7-9 Datum Selection 7-16, 7-18 Dedicated Keys 1-4, 1-14, 1-16 ALARMS 3-19, 3-20, 6-4 CLEAR 1-16 DISPLAY 1-5, 2-7, 2-8, 6-9 GAIN 3-7 MARKS 4-4, 4-5, 5-9, 5-10, 5-29, 6-6 MENU 2-5, 5-30, 6-8, 7-1, 7-2 MULTI 2-6, 3-5, 3-7, 3-22 POWER 2-2, 2-3, 2-4 RANGE 2-22, 2-23, 3-2, 5-2 VRM/EBL 3-13, 3-14, 6-1, 6-3 Deleting a Guard Zone 3-19 a VRM/EBL 3-16 Deleting - See Erasing 5-12 Depth Data Box 7-4 Determining Radar Range 3-3
Display Brightness 2-6 Cleaning 9-1 Features 1-5 Lighting 2-6 Operating Modes 1-5 Selecting 2-7 DISPLAY Key 1-5, 1-16, 2-7, 2-8, 6-9 Display Options Chartplotter 1-11 Fishfinder 1-8 Radar 1-8 Display Timing Set Up 7-14 Display Unit 1-4 Connections 8-13 Console Mounting 8-10 Grounding 8-12 Location 8-5 Mounting 8-10 Specification A-1 Switching Off 2-4 Displaying Bearing Data (EBLs) 7-10 Chart Data 5-3 Waypoint Data 5-8, 5-10, 5-19 Displaying the Radar and Synchronising Radar & Chart 2-32
Chartplotter 1-11, A-3 Display 1-5 Radar 1-8 Find Ship 2-20 Fishfinder Definition 1-3 Mode 1-6 Simulator 2-5 Window Options 1-6, 2-10 Fishfinder Master 1-3 Fishfinder Repeater 1-3 Floating VRM/EBLs 3-14, 3-16 Follow a Route 5-23 Stop 5-23 FTC Control 3-4, 3-7, 3-10 Functions Chartplotter 1-13 Radar 1-10

RL70CRC Pathfinder Radar & Chartplotter 1-1 RL80C Pathfinder Radar 1-1 RL80CRC Pathfinder Radar & Chartplotter 1-1 Route Clearing 5-14 Creating 5-14 Current 5-14 Data Display 5-15 Database List 5-13, 5-15, 5-16, 5-19 Editing 5-15, 5-21 Erasing 5-15 Follow 5-23 Naming 5-15, 5-16 NMEA Transfer 5-28 Retrieving 5-14 Saving 5-14 Transfer 5-14 Route Leg 5-14 Data Display 5-19 Routine Checks 9-1 Ruler Data Box 6-2, 6-3
Safety iii, 5-1 Electromagnetic Energy iii EMC Guidelines 8-2 High Voltage iii Navigation Aid iii Saving a Route 5-14 Scale Chart 2-20, 5-2, 5-15, 6-6 Radar Range 3-2 Custom 7-10 Scanner iii, 1-4 Connection 8-13, 8-14 Modes Scanner Off 2-2, 2-3 Standby 1-4, 2-2, 2-3 Timed Transmit 1-5, 7-10, 7-11 Transmit 1-4, 2-2 Switching Off 2-4 Transmission Check 8-17 Scanner Off Mode 2-2, 2-3 Scenarios Displaying the Radar and Synchronising Radar & Chart 2-32 Make & Follow a Route 2-28 Place & Goto a Waypoint 2-26 Review Your Passage Plan 2-30 Sea Clutter Control 3-4 Recommendations 3-9 SeaTalk 1-4 Connection 8-13, 8-23, 8-25 Data 4-1, 4-4, 4-5, 4-6, 6-1, 6-7, 7-8, 8-25
Selecting a Half Screen Window 2-8 a Waypoint 5-8 the Heading Mode 4-3 the Operating Mode 2-7 Servicing EMC Guidelines 9-1 Setting Alarms and Timers 6-1 Setting Up a GPS 6-1, 6-8 Chart Parameters 7-2, 7-16 MARPA 7-2 Radar Parameters 7-2 System Parameters 7-2 Tracks 5-30 Shadows 3-6 SHM (Ship's Heading Marker) 1-8, 3-19 Head Up Mode 2-18 Side Lobes 3-5 Simulator 7-5, 7-9 Chart 2-1, 2-5 Fishfinder 2-5 Radar 2-1, 2-5 Soft Key Labels 7-6 Soft Keys 1-4, 1-14, 1-17 Keys Soft 7-4, 7-6 SOG (Speed Over Ground) Data Box 7-4 Source 5-4 Speed 6-6 Data Box 7-4 Standby Mode 1-5, 2-2, 2-3 Status Bar 1-8, 1-11 STC Preset 7-15 Stop Follow 5-23 Goto 5-23 Track - See Clear Track Switching Databoxes On/Off 2-14, 3-18 Range Rings On and Off 2-13 the Chart On 2-4 the Cursor Data Box On and Off 2-13 the Display On and Off 2-4 the Scanner Off 2-4 Symbol Marks 7-10, 7-11 MOB 4-5, 6-6 Waypoint 5-8, 5-11, 7-16, 7-18 Synchronize Chart and Radar 1-11, 2-21, 7-16 System Connections 8-12 Grounding 8-12 Set Up 7-2
Target Acquire 3-26 Cancel 3-26, 3-27 Data 3-27 Target (Chart) 5-23 Arrival 5-23 Goto 5-23 Waypoint 5-23 Target Tracking 3-1 Targets (Radar) 1-4, 2-3 Control 3-5 Expansion 3-5, 3-11 Interference Rejection 3-5, 3-11, 3-12 Wakes 3-5, 3-11 MARPA 1-10, 3-1 Temperature Data Box 7-4 Terminology 1-3 Tide Data 5-4, 5-5 Tide Set/Drift Data Box 7-4 Tide Vector 7-16, 7-18 Time Data Box 7-4 Time Format 7-5 Time Offset 7-5 Timed Transmit Mode 1-5, 7-10, 7-11 Timers Alarm Clock 6-4 Countdown 6-4 Setting 6-1 Trackpad 1-4, 1-14, 2-20 Tracks Clearing 5-30, 5-31 Database List 5-31 Managing 5-30, 5-31 Setting Up 5-30 Transfer Route 5-14 Transmission Check 8-17 Transmit Mode 1-5, 2-2, 2-3 Tune Preset 7-15 Tuning the Receiver 3-5, 3-9