Impulse Response Utility

User Manual
Copyright 2009 Apple Inc. All rights reserved. Your rights to the software are governed by the accompanying software license agreement. The owner or authorized user of a valid copy of Logic Studio software may reproduce this publication for the purpose of learning to use such software. No part of this publication may be reproduced or transmitted for commercial purposes, such as selling copies of this publication or for providing paid for support services. The Apple logo is a trademark of Apple Inc., registered in the U.S. and other countries. Use of the keyboard Apple logo (Shift-Option-K) for commercial purposes without the prior written consent of Apple may constitute trademark infringement and unfair competition in violation of federal and state laws. Every effort has been made to ensure that the information in this manual is accurate. Apple is not responsible for printing or clerical errors.
Note: Because Apple frequently releases new versions and updates to its system software, applications, and Internet sites, images shown in this manual may be slightly different from what you see on your screen. Apple 1 Infinite Loop Cupertino, CA 95014 408-996-1010 www.apple.com Apple, the Apple logo, Logic, Logic Studio, and Mac are trademarks of Apple Inc., registered in the U.S. and other countries. Other company and product names mentioned herein are trademarks of their respective companies. Mention of third-party products is for informational purposes only and constitutes neither an endorsement nor a recommendation. Apple assumes no responsibility with regard to the performance or use of these products.

Contents

Preface
An Introduction to Impulse Response Utility About Impulse Response Utility About the Impulse Response Utility Documentation Additional Resources

Chapter 1

7 Understanding Deconvolution and Impulse Responses 7 Impulse Response Recording: Transients Method 8 Impulse Response Recording: Sine Sweep Method Setting Up Your Impulse Response Recording Environment Ideal Impulse Response Recording Setup Alternative Impulse Response Recording Setup Speaker and Microphone Selection Suggestions Speaker and Microphone Placement Suggestions Creating Impulse Responses in Impulse Response Utility Getting to Know the Interface Understanding the Workflow Creating Your Project Assigning Input and Output Hardware Configuring the Monitoring Parameters Configuring the Sweep Generator Recording Audio into Impulse Response Utility Deconvolving Your Impulse Response Editing Your Impulse Response Auditioning Your Impulse Response Creating a Space Designer Setting Saving, Opening, and Reverting to Saved Projects

Chapter 2

Chapter 3

Chapter 4

33 Recording Impulse Responses from Audio Equipment 33 Recording Impulse Responses from Guitar Speakers 34 Recording Impulse Responses from Hardware Devices

Chapter 5

35 B-Format Surround Encoding 36 Advantages of B-Format Surround Encoding 36 Microphone Suggestions for B-Format Recording 39 Impulse Response Utility Tutorial 39 Creating a Five Channel Surround Impulse Response 40 Recording a Mono to Omni 5 Channel Impulse Response

Appendix

An Introduction to Impulse Response Utility
Impulse Response Utility is a multi-track audio recording and deconvolution application. It is designed to enable you to create your own impulse response files for Space Designer, the convolution-based reverb effect of Logic Studio. Although Space Designer comes with plenty of great sounding Halls, Delays, and other Reverbs, you might want to create an impulse response of your own studio, kitchen, bathroom, or even teapot. This preface covers the following: About Impulse Response Utility (p. 5) About the Impulse Response Utility Documentation (p. 5) Additional Resources (p. 6)
About Impulse Response Utility
Impulse Response Utility is designed to work seamlessly with Space Designer. You can record and edit impulse responses and create Space Designer files quickly and easily. All tools needed to master the complex process of creating an impulse response, such as a flexible sweep generator, powerful editing facilities, and one-click creation of Space Designer settings, are included. All you need is your Mac, Impulse Response Utility and, of course, an audio interface connected to speakers and microphones.

Impulse Response Recording: Transients Method
This method involves the recording of an impulse in a space, using a device such as a starter pistol. The gunshot is the impulse, and the audio file you record captures both the impulse (gunshot) and the room response. The advantage of this method is that the recorded audio file can be used in Space Designer without any further processing. You can use Impulse Response Utility to record your starter pistol impulses, and then combine them into a Space Designer Impulse Response (.sdir) file (and Space Designer setting file). The disadvantage of this method is that its extremely difficult to make a perfect, undistorted recording of a starter pistol shot. This is due to the extremely loud nature of the initial transient of the shot. A further issue is that starter pistol shots contain very little high or bass frequency informationwhich, in turn, limits the usable frequency range of the convolved reverb.
Impulse Response Recording: Sine Sweep Method
This is the preferred method for creating impulse responses. It involves playing a broadband audio sine sweep into a space, and recording the sweep (and space) at optimal recording levels. A sine sweep that covers the entire audible frequency range is used, resulting in a broad-range, and often higher-quality, impulse response. The recorded sine sweep audio file cannot directly be used as an impulse response. The recorded file contains all the echoes and reflectionsin other words, the responseof the space, stretched out over the length of the sine sweep. This is very different from the starter pistol approach, where the response is contained at the beginning of the file in an impulse. When you use a sine sweep, Impulse Response Utility uses a process called deconvolution to time align and level align all recorded reflections-that are present over the entire recorded sine sweepinto the very beginning of the file. This results in an impulse response that Space Designer can use to combine, or convolve, with your audio signal. Impulse Response Utility can then generate an.sdir setting from the impulse response.
Chapter 1 Understanding Deconvolution and Impulse Responses
Setting Up Your Impulse Response Recording Environment
Prior to using Impulse Response Utility to create an impulse response, you need to set up your recording hardwareallowing playback and recording of the sine sweep that Impulse Response Utility will generate. The impulse response of a space is never just the spaces impulse response. The recorded impulse response is always the response of the complete systemin other words, every piece of equipment you use in the recording process. This includes, in signal-flow order: the digital-to-analog converter, the amplifier and speakers (or powered speakers), the room characteristics, the microphones, and finally the microphone pre-amp and analog-to-digital converter. So, before leaving your studio to do any location recording, you have to think about your equipment. These days, even budget converters offer acceptable quality, so your main concern will be your selection of speakers and microphones. This chapter covers the following: Ideal Impulse Response Recording Setup (p. 9) Alternative Impulse Response Recording Setup (p. 11) Speaker and Microphone Selection Suggestions (p. 12) Speaker and Microphone Placement Suggestions (p. 12)

This method can create the impression of the audio signal being completely immersed in the simulated space.
The Auralization Approach
Another common strategy for placing speakers and microphones in a space uses the auralization approach. This technique attempts to capture the reflections from the performers perspective. Place one or more speakers at the performers location (or another audio source) and place the microphone at the listening position. The resulting impulse response should sound like your audio is being played back from these specific speaker locations. For example, you can make a stereo impulse response of a particular stage using the auralization technique, and when you use the IR in Space Designer, your audio should sound like it is on that stage. The image below illustrates use of the auralization technique to set up your speakers and microphones for a true stereo impulse response.

Audience

To capture a surround impulse response that represents being in the audience of a space, set up two speakers in the performers position as above, but place a surround array of microphones around the room. This can create a realistic feeling (and effect) of being in the audience when the performance is coming from in front of you. This can help to create a surround-like effect from a live stereo recording.
The Virtual Echo Chamber Approach
A good alternative to the auralization approach is placement of your speakers and microphones in a way that creates a virtual space that resembles a physical echo chamber. To create this kind of impulse response, face the loudspeakers toward the corners, and the microphones toward the opposite corners. This is how microphones in a physical echo chamber would be placed. This eliminates a direct path from the speaker to the microphone, and captures more reflections. The image below illustrates how you could set up two speakers and two microphones to create a stereo impulse response, using this virtual echo chamber approach.
The resulting impulse response allows you to mix the reverb into the dry signal, without any phase cancellation issues caused by early reflections or direct signals. This approach works particularly well if you want to keep your signal mostly dry, without any alteration or coloration from the reverb, but still want to add a high fidelity reverb tail to your audio. You can also use this method for surround or multi-channel reverbs. The main concept to remember is that the speakers should be pointing at the wall, to eliminate direct paths between microphones and speakers. The illustration below offers a possible layout for a five channel reverb chamber. The loudspeakers, placed in a circle, are directed at the walls, and the microphone array is in the center of the circle.

Creating Impulse Responses in Impulse Response Utility
This chapter covers the creation of your own impulse responses for use in Space Designer. This chapter covers the following: Getting to Know the Interface (p. 18) Understanding the Workflow (p. 18) Creating Your Project (p. 19) Assigning Input and Output Hardware (p. 20) Configuring the Monitoring Parameters (p. 21) Configuring the Sweep Generator (p. 22) Recording Audio into Impulse Response Utility (p. 23) Deconvolving Your Impulse Response (p. 26) Editing Your Impulse Response (p. 27) Auditioning Your Impulse Response (p. 28) Creating a Space Designer Setting (p. 30) Saving, Opening, and Reverting to Saved Projects (p. 31)
Getting to Know the Interface
All parameters and functions that you need to create impulse responses are contained in a single screen.
Hardware I/O Assignment area Editing area
Monitor and Sweep Generator section

Inputs/Track section

The Impulse Response Utility interface is divided into four areas: Hardware I/O Assignment area: Contains pop-up menus that enable selection of the audio input and output device. Monitor and Sweep Generator section: Contains monitoring and sine sweep generation parameters, plus buttons to deconvolve your audio tracks into an impulse response, and to audition your IR. Inputs/Track section: Lists all audio tracks used for your impulse response recordings. Editing area: Displays the audio information of the currently selected audio track.
Understanding the Workflow
Creating an impulse response in Impulse Response Utility consists of the following stages: Stage 1: Creating a New Impulse Response Project Configure your Impulse Response Utility project for the number of tracks your impulse response format requires. Stage 2: Setting Impulse Response Utility Parameters Set the hardware I/O, monitor, and sweep parameters for your audio track recordings.
Chapter 3 Creating Impulse Responses in Impulse Response Utility
Stage 3: Recording Use Impulse Response Utility to record the audio tracks needed for your impulse response. Stage 4: Deconvolving Your Audio Recordings Assuming you have recorded sine sweeps, click Deconvolve after all audio tracks have been recorded. Impulse Response Utility will generate an impulse response from your tracks. Stage 5: Editing and Auditioning Cut silent portions, apply fades, and so on, to optimize your impulse response. Stage 6: Creating a Space Designer Setting Click Create Space Designer Setting when finished with the steps above. This adds the newly created impulse response to your list of available Space Designer settings.

Creating Your Project

When you first open Impulse Response Utility, you will be presented with the New Impulse Response Project dialog. This is the first step in creating a new impulse response project. You can also create a new impulse response project by choosing File > New Project (or pressing Command-N).
Impulse Response Utility offers formats ranging from conventional stereo impulse responses, true stereo (where each channel is processed discretely), quadraphonic formats, or five, six, or seven channel surround formats. These latter formats can be in either traditional multi-track, or B-Format encoding. See B-Format Surround Encoding for more information. You can also create multi-channel impulse responses in Impulse Response Utility by using the Mono to Omni Discrete impulse response format. This only requires the recording of one speaker by as many channel microphones as needed (for the chosen format). The resulting impulse response places a lower strain on your CPU. See Recording a Mono to Omni 5 Channel Impulse Response. To create a new impulse response project 1 Choose an impulse response format from the Configuration pop-up menu.
In the window below the Configuration pop-up menu, the dialog displays the number of speaker and microphone positions required by the selected format. 2 Click OK This exits the New Impulse Response Project dialog, and the required number of tracks (determined by the format you chose) are shown in the Inputs/Track section.
Assigning Input and Output Hardware
You need to set up the audio input and output device in the Hardware I/O Assignment area before you can use Impulse Response Utility.
The audio input selection determines the audio device used to record audio tracks. The audio output selection determines the audio device used to monitor the recorded signal, and to play back the generated sine sweep.
To select an audio input device In the Audio Input pop-up menu, choose an audio interface driver. To select an audio output device In the Audio Output pop-up menu, choose an audio interface driver. Note: Although the Hardware I/O Assignments area also displays the current sample rate, you cannot change the sample rate of your impulse response project in Impulse Response Utility. If you want to record your audio tracks at a different sample rate, you will need to change it in the Audio MIDI Setup utility, or in the software for your audio interface (if applicable). Consult the documentation for your audio interface if youre unsure.
Configuring the Monitoring Parameters
Once you have recorded sine sweep tracks into Impulse Response Utility, you can monitor them through a stereo output of your choice. The monitor controls determine the monitor channel and level. You can also mute the monitor section.

To select the stereo monitor output channels Choose the desired stereo output pair from the Monitor Channel menu.
To adjust the output level of the monitored signal 1 Click inside the Monitor Level field. 2 Do one of the following: Drag left (or down) to reduce the volume, or right (or up) to raise the volume. Type a numeric value for the monitor level (any value above 0 dB will set the monitor level at 0 dB). Important: To avoid audio feedback when recording, be sure to mute the monitor output.
To mute the monitor output Select the Monitor Mute checkbox.
Configuring the Sweep Generator
The sweep generator produces a sine wave that sweeps smoothly from 20 Hz up to 20 kHz. The sweep generator parameters set the hardware output, volume, length, reverb time, and pre-roll of the sine sweep.
Sweep Channel pop-up menu: Choose the input channel that you want to use. Test Tone pop-up menu: Choose a test tone frequency for the integrated, sustaining (in other words, non-sweeping) sine wave tone generator. This facility helps you to calibrate your hardware outputs. Use this test tone to ensure that your hardware output channel is connected properly, and that your speakers can reproduce the selected sine wave frequency. On checkbox: Select to hear the test tone. Sweep Level field: Sets the level of the test tone. Sweep Length pop-up menu: Sets the sweep duration. Ideally, you want your sine wave to be short. This avoids artifacts in your recording due to air motion, rattling of interiors, and other ambient noise. Unfortunately, short sweeps may not yield high enough signal-to-noise ratios in some recording situations. If you find that the results obtained from recording with a 10-second sweep arent all you hoped for, try the 50-second sweep. There are three length options for the sine sweep: 10s: A 10-second sine sweep 50s: A 50-second sine sweep Off: No sine wave sweep. Choose this setting if you are recording a starter pistol impulse. Reverb Time field: Determines the maximum recording time for each track. In order to accurately capture the acoustic properties of a space, you should set a value that is long enough to capture the decay phase of all reverberations and echoes.
If you are using the sweep generator, the reverb time will start when the sine sweep ends. If you have the Sweep Length set to Off (in order to record a starter pistol impulse response), the Reverb Time parameter determines the entire length of the recording. Preroll checkbox: You want to be sure that any operator noise, such as typing, readjusting microphones, and so on, is not recorded. You can set a pre-roll for just this purpose; recording wont start immediately, giving you time to finish typing, make last-minute mic corrections, and so on. The pre-roll length equals the time you set with the Reverb Length parameter.

Recording Audio into Impulse Response Utility
Once you have made hardware assignments and configured the monitor and sine sweep parameters, its time to start recording audio tracks. If you are using the sweep generator, you will hear the sine wave sweep up through its frequency range. Impulse Response Utility will record the result onto the selected audio track(s). If you have set the sweep generator to Off, click Record, and shoot your starter pistol. Impulse Response Utility will record the resulting impulse response onto the selected track. To select an audio track Do one of the following:
Click in a track lane. Use the Up and Down Arrow keys to navigate through the track list.
To record in Impulse Response Utility 1 Select an audio track in the Inputs/Track section. 2 Configure the audio track for recording. 3 Repeat this step for each track required by the chosen format. 4 Click the Sweep/Record button to begin recording.
Configuring Audio Tracks for Recording
The Inputs/Track section is automatically filled with the number of tracks required for the impulse response recording, based on your selections in the New Impulse Response Project dialog. Every track lane in the Inputs/Track section has a number of parameters. Some are automatically configured by Impulse Response Utility; others you will need to set before recording.
Track Parameters Speaker Position pop-up menu: Selects the speaker position label for the selected track. Both Impulse Response Utility and Space Designer use these labels to identify, and process, the audio files that comprise a multi-channel stereo or surround impulse response. Impulse Response Utility automatically sets the speaker position label for each track, but you can change these labels to any other position (available in the current impulse response format), if desired. Mic Position pop-up menu: Selects the mic position label for the selected track. Both Impulse Response Utility and Space Designer use these labels to identify, and process, the audio files that comprise a multi-channel stereo or surround impulse response. Impulse Response Utility automatically sets the mic position label for each track, but you can change these labels to any other position (available in the current impulse response format), if desired. Input pop-up menu: Sets the physical input for each track. Be sure to select the correct input before recording. S[olo] button: Click to engage or disengage solo mode for the selected track. When the Solo button is engaged (yellow), the input signal is routed to the monitor section, and the input level is displayed in the VU meter (see VU meter below). Only one track can be soloed at a time. R[ecord-Enable] button: Places the selected track into record-ready mode. The R button turns red when engaged. Clicking this button also activates the Solo button for the selected track, allowing you to monitor the input signal before recording. You can record-enable several tracks at once, for multi-channel recording. When you click Sweep/Record, a recording will be made on all record-enabled tracks. L[ock] button: As soon as one track is locked, the sweep generator parameters are also locked. This ensures that any subsequent recordings will use identical sweep settings. This is necessary, as every track must use an identical sine sweepin order to produce a phase coherent, accurate, multi-channel impulse response.

Click the Deconvolve button.
Choose Edit > Deconvolve (or press Shift-Command-D). Following deconvolution, your audio tracks will be a single impulse response that you can audition, edit, and turn into an.sdir setting. Note: While it is possible to deconvolve each audio track once recorded, theres really no point in working this way; its far more efficient to wait until all tracks are recorded, and then deconvolve them.
Editing Your Impulse Response
When you have finished recording your audio tracks, you may feel that they have superfluous silence at the beginning or end of the file, dont fade out early enough, and so on. To address these minor issues, Impulse Response Utility allows you to cut, crop, and fade your audio files in the Editing area.
To view an audio file in the Editing area Select the audio file. Your audio file will automatically appear in the Editing area.
You can choose from three different display modes by clicking the buttons at the top of the Editing area: Waveform button: Shows the recorded audio as a standard waveform. The horizontal axis displays the elapsed time. The vertical axis displays the audio level as a percentage. Energy button: Shows the sound energy distribution over time. The horizontal axis displays the elapsed time. The vertical axis displays audio levels in dB. Spectrogram button: Shows the frequency distribution over time. The horizontal axis displays the elapsed time. The vertical axis displays the frequencies, which are color-coded by dB range. The color legend in the upper-right corner of the Editing area indicates the color schema. These display modes allow you to effectively analyze your waveforms, making it easy to identify material you need to cut or crop, or that requires a fade. The Spectrogram mode, in particularwhich simultaneously shows frequency, level, and timeallows for very detailed analysis of your audio. To select and play part of an audio file in the Editing area 1 Drag horizontally over the desired section.
2 Audition your selection by clicking the Play button. Click the Cycle button to continuously play back the selected track.
To edit the selected part of an audio file Choose one of the editing operations from the buttons at the top-left corner of the Editing area: Crop button: If you make a selection that doesnt extend to either the beginning or end of the audio, the left edit button activates the Crop function. Clicking this button will remove the audio to the right and left of your selection, without touching the selected audio. You can also choose Edit > Crop (or press Command-X) to crop. Cut button: If you make a selection that extends to either the very beginning or very end of the audio, the left edit button activates the Cut function. Clicking this button will remove the selected audio, without touching the unselected audio. You can also choose Edit > Cut (or press Command-X) to cut. Fade button: If you make a selection that includes either the very beginning or end of the audio, you can select the Fade function. Clicking this button creates a gradual fade over the length of the selection area. You can also choose Edit > Fade (or press Command-F) to fade. Note: In order to maintain phase coherency between all tracks of your impulse response, edits are performed across all tracks equally. To ensure that your impulse response cannot include tracks that are not edited equally, you are prevented from recording further tracks once an edit has been made.

Auditioning Your Impulse Response
To really know how your impulse response will sound when used in Space Designer, you need to be able to listen to it in context. Impulse Response Utility includes an Audition window for just this purpose, where the loaded impulse response can convolve test audio files. The Audition window is divided into three sections: the Impulse Response area, the Monitor area, and the Audio Test Files area.
The appearance of the Audition window changes slightly when using a B-Format impulse response. The B-Format Audition window removes the Output Channel parameter from the Track area and includes a Loudspeaker area:
Audition Impulse Responses window
Audition B-Format Impulse Responses window
Impulse Response Utility allows up to five audio files to be loaded/used as sources when auditioning your impulse response. The Audition window also includes four test source files.
To open the Audition window Click the Audition IR button. The Audition window will open. All editing functions are disabled while the Audition window is open. Audition Impulse Response Window Parameters Enable checkbox: Enables or disables individual impulse response recordings. Use these boxes to select the specific file (or files) you want to audition. Input ID label: Identifies the specific impulse response file by its speaker > mic positions. Output Channel pop-up menu (not available for B-Format Impulse Responses): Selects the physical output channel used for playback of the selected impulse response. Mix field: Determines the ratio of dry test source signal to wet effect signal.
Monitor Level field: Sets the overall auditioning volume. Test Audio File buttons: Plays one of the four included test source audio files. Open buttons: Click to load an audio file for use as a test source. Any uncompressed audio file can be used. Play buttons: Click to play the selected audio file through the enabled impulse response file (or files). Loudspeaker Area Parameters (B-Format Specific) Number of Loudspeakers field: Determines the number of loudspeakers that Impulse Response Utility will decode the impulse response into. Click the arrows to increase or decrease the number of speakers, or double-click the number of speakers and type in a new value. Loudspeaker Angle field: Allows you to configure the angle of each loudspeaker. The B-Format decoding takes this into account when re-creating the recorded space. Output Channel pop-up menu: Sets the physical output channel for the selected loudspeaker.
Creating a Space Designer Setting
Once you are satisfied with your impulse response, the final step is to generate an.sdir file, and a plug-in setting. When done, your newly created impulse response can be used in Space Designer. To create a Space Designer setting Do one of the following:
Click the Create Space Designer Setting button.

Choose File > Create Space Designer Setting. Impulse Response Utility will generate an.sdir file of your impulse response and save it in the following directory: ~/Library/Application Support/Logic/Impulse Responses. A plug-in setting file for your impulse response is also generated and saved in the following directory: ~/Library/Application Support/Logic/Plug-In Settings/Space Designer. The next time you open Logic, your newly created impulse response will be available in the Library, and within the Space Designer interface.
Saving, Opening, and Reverting to Saved Projects
The Impulse Response Utility project file is a Mac OS X package file, that contains all files associated with the project.

Saving Projects

Impulse Response Utility automatically saves your project as soon as you record audio (see Automatic Saving of Projects). You can manually save your project at any time, however. You can also open a previously saved project, or revert the current project back to its last saved state.
To save your project with its current name and location Choose File > Save Project (or use Command-S) to save your IR Project with its current name, in its current location. To save your project with a new name or location Choose File > Save As (or use Command-Shift-S).

Opening Projects

If youd like to continue working on a previously saved project, you first need to open it. To open a project Choose File > Open Project (or press Command-O), then navigate to your project file. Choose File > Open Recent to open a hierarchical menu of recently opened project files.
Reverting to Saved Projects
If you are unhappy with the edits or recordings made in your current projectand you have saved the projectyou can use the File > Revert to Saved command. This returns the project to its last saved state. Note: Once you use the Revert to Saved command, you will lose all unsaved changes.
Recording Impulse Responses from Audio Equipment
You arent limited to creating impulse responses from rooms and spaces. You can make an impulse response from any device that you can play a broadband sine sweep into (and record the results). Two examples are guitar speaker cabinets and hardware processing devices, such as tube equalizers and reverb effects units. This chapter covers the following: Recording Impulse Responses from Guitar Speakers (p. 33) Recording Impulse Responses from Hardware Devices (p. 34)

Chapter 4 Recording Impulse Responses from Audio Equipment
B-Format Surround Encoding
B-Format is a special way of encoding spatial information. It represents space using four audio streams: one to capture the sound pressure (W), and three to capture the X (front-to-back), Y (left-to-right), and Z (top-to-bottom) room coordinates. The following illustration shows you how these four audio streams interact with each other, to create a three-dimensional spatial image.
Height Z Front X Right Y W

Y Left

X Rear
Space Designer can decode and convolve these four streams into reverbs, in all supported surround formats. Space Designer offers a comprehensive library of B-Format impulse responses that use all four streams (W, X, Y, and Z). As impulse responses do not make use of Z-axis information, Impulse Response Utility only records and encodes information from the W, X, and Y positions, saving CPU resources and disk space. Impulse Response Utility allows you to encode all supported surround impulse response formats in B-Format. This chapter covers the following: Advantages of B-Format Surround Encoding (p. 36) Microphone Suggestions for B-Format Recording (p. 36)
Advantages of B-Format Surround Encoding
One advantage of the B-Format is that it can capture a surround image with fewer audio files. Normally, you need to record every speaker position from every microphone position, to correctly record surround information. With B-Format, these four (or three, in Impulse Response Utility) audio streams are all you need to capture audio from each speaker. As an example, imagine you are using a five channel setup, and want to use Impulse Response Utility to create a five channel impulse response. Using traditional methods, you would need to record all five speakers from all five microphone positions, resulting in 25 audio files. If you choose to create your project as a five channel B-Format impulse response, you will only need to record 15 audio filesthree audio recordings (W, X, and Y) from each of the five speaker positions. As you can see, B-Format encoded surround impulse responses require far fewer audio files, which means they require less hard drive space, as well as needing less RAM and CPU cycles when decoded in Space Designer. A second advantage to B-Format encoding is phase coherency when using multiple microphones at once. Whenever you use multiple microphones, differences in the time it takes sound to reach each microphone can result in phase cancellations and phase shifts, which can affect the quality of your impulse response. As the point of reference is always the same when using B-Format encoding, there will be no phase issues, even when using multiple microphones to record your impulse response.

Recording a Mono to Omni 5 Channel Impulse Response
The process in Creating a Five Channel Surround Impulse Response is an example of recording a true surround impulse response. In many cases, it is sufficient to record one speaker position, thus creating a mono/omni discrete impulse response. Mono/omni discrete impulse responses are not only easier and faster to record, but also place a lower strain on the CPU. To create a mono to Omni 5 Channel impulse response 1 Choose the Mono/Omni to 5 channel template in the New Projects dialog. You will see that mono/omni discrete projects only require one speaker. 2 Aim your speaker toward the ceiling or a back wall.
Appendix Impulse Response Utility Tutorial
3 Point your microphone to the first surround position: Front-Left, for example. 4 Record the sweep. 5 Repeat the process for all remaining microphone positions.