Instructions for use

WASHING MACHINE Contents

Installation, 38-39 GB

English Unpacking and levelling, 38 Electric and water connections, 38-39 The first wash cycle, 39 Technical details, 39
Washing machine description, 40-41
Control panel, 40 How to open and shut the drum, 41 Leds, 41
Starting and Programmes, 42
Briefly: how to start a programme, 42 Programme table, 42

Personalisations, 43

AVTL 89
Setting the temperature, 43 Setting the spin cycle, 43 Functions, 43
Detergents and laundry, 44
Detergent dispenser, 44 Bleach cycle, 44 Preparing your laundry, 44 Special items, 44 Woolmark Platinum Care, 44
Precautions and advice, 45
General safety, 45 Disposal, 45 Saving energy and respecting the environment, 45

Care and maintenance, 46

Cutting off the water or electricity supply, 46 Cleaning your appliance, 46 Caring for your appliance door and drum, 46 Cleaning the pump, 46 Checking the water inlet hose, 46 Cleaning the detergent dispenser, 46
Troubleshooting, 47 Service, 48
Before calling for Assistance, 48

Installation

Keep this instruction manual in a safe place for
future reference. Should the appliance be sold, transferred or moved, make sure the instruction manual accompanies the washing machine to inform the new owner as to its operation and features. loosening the adjustable front feet (see figure); the angle of inclination, measured according to the worktop, must not exceed 2. Levelling your appliance correctly will provide it with stability and avoid any vibrations, noise and shifting during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the washing machine.
Read these instructions carefully: they contain vital information on installation, use and safety.

Unpacking and levelling

Unpacking
1. Unpack the washing machine. 2. Check whether the washing machine has been damaged during transport. If this is the case, do not install it and contact your retailer. 3. Remove the four protective screws and the rubber washer with the respective spacer, situated on the rear of the appliance (see figure). 4. Seal the gaps using the plastic plugs provided. 5. Keep all the parts: you will need them again if the washing machine needs to be moved to another location. Warning: should the screws be re-used, make sure you fasten the shorter ones at the top.
Electric and water connections
Connecting the water inlet hose
1. Insert seal A into the end of the inlet hose and screw the latter onto a cold water tap with a 3/4 gas threaded mouth (see figure). Before making the connection, allow the water to run freely until it is perfectly clear. 2. Connect the other end of the water inlet hose to the washing machine, screwing it onto the appliance's cold water inlet, situated on the top right-hand side on the rear of the appliance (see figure). 3. Make sure there are no kinks or bends in the hose.
Packaging materials are not children's toys.

Levelling

Your machine may make a considerable amount of noise if the two front feet have not been adjusted correctly. 1. Install the washing machine on a flat sturdy floor, without resting it up against walls, furniture cabinets or other. 2. If the floor is not perfectly level, compensate for any unevenness by tightening or
The water pressure at the tap must be within the

values indicated in the Technical details table (on the next page).
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Connecting the drain hose
outdoor environment, not even when the area is sheltered, because it may be very dangerous to leave it exposed to rain and thunderstorms.

65 - 100 cm

Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor;
When the washing machine is installed, the main socket must be within easy reach. Do not use extensions or multiple sockets. The power supply cable must never be bent or dangerously compressed. The power supply cable must only be replaced by an authorised serviceman.
Warning! The company denies all liability if and when these norms are not respected.

Description Programmes

alternatively, place it over the edge of a basin, sink or tub, fastening the duct supplied to the tap (see figure). The free end of the hose should not be underwater.

The first wash cycle

Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, setting the 90C programme without a pre-wash cycle.

Detergents

Technical details
We advise against the use of hose extensions; in case of absolute need, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.

M ode l

AVT L 8 9

Precautions

Dim e nsions
cm w ide cm h ig h cm deep from 1 to 5 kg vo ltage /Vo lts 50 Hz max imu m abs o rbed po w er 50 W maximu m pres s u re 1 MPa (10 bar) min imu m pres su re 0.MPa (0.5 bar) dru m capacity 42 litres u p to rpm

Capacity

Electric connection
Electric connections Wate r connections Spin spe e d Control program m e s according to IEC456 dire ctive
Before plugging the appliance into the mains socket, make sure that: the socket is earthed and in compliance with the applicable law; the socket is able to sustain the appliance's maximum power load indicated in the Technical details table (on the right); the supply voltage is included within the values i ndicated on the Technical details table (on the right); the socket is compatible with the washing machine's plug. If this is not the case, replace the socket or the plug.
prog ramm e 3 ; temperatu re 60 C; ru n w ith a load o f 5 kg.

Troubleshooting

T h is applian ce is com plian t w ith th e follow in g Eu ro pean Co mmu n ity D irectives : - 7 3//CEE of 1 9/0 2/(L o w Vo ltag e) an d s u bs equ en t amen dmen ts - 8 9/6/CEE o f 03 /05 /(Electrom ag n etic Compatibility) an d s u bs equ en t amen dmen ts - 2 /96 /CE

Service

The washing machine should not be installed in an
Washing machine description

Control panel

SPIN SPEED

TEMPERATURE

ON/OFF

LID LOCKED

START/RESET

FUNCTION

PROGRAMME knob
Detergent dispenser to add detergent and fabric softener (see page 44). LEDs to find out which wash cycle phase is under way. If the Delay Timer function has been set, the time left until the programme starts will be indicated (see page 41). SPIN SPEED knob to set the spin speed or exclude the spin cycle completely (see page 43). FUNCTION keys to select the functions available. The button corresponding to the function selected will remain on.
TEMPERATURE knob to set the temperature or the cold wash cycle (see page 43). ON/OFF key to turn the washing machine on and off. START/RESET key to start the programmes or cancel incorrect settings. ON-OFF/LID LOCK led ,to find out whether the washing machine is on (flashing) and if the lid may be opened (see page 41). PROGRAMME knob to set the programmes (see page 42). The knob stays still during the cycle.
ON-OFF/LID LOCK led: If this LED is on, the appliance Lid is locked to prevent it from being opened accidentally; to avoid any damages, you must wait for the lamp to flash before you open the Lid. The rapid flashing of the ON-OFF/LID LOCK Led together with the flashing of at least one other LED indicates there is an abnormality. Call for Technical Assistance.
How to open and to close the drum

A) Opening (Fig. 1).

Lift the external lid and open it completely.
B) Opening the drum (Soft opening): With one finger, push the button indicated in fig. 2 and the drum will open delicately. With one finger, push the button indicated in fig. 2 and the drum will open delicately.

Description

Fig. 1

Fig. 2

C) Loading the washing machine. (Fig. 3). D) Shutting (Fig. 4). - close the drum fully by first shutting the front door followed by the rear one; - then ensure the hooks on the front door are perfectly housed within the seat of the rear door; - after the hooks have clicked into position, press both doors lightly downwards to make sure they do not come loose; - finally shut the external lid.

Programmes Detergents

Fig. 3

Fig. 4

The LEDS provide important information. This is what they can tell you: Delay set: If the Delay Timer function has been enabled (see page. 43), once you have started the programme, the LED corresponding to the delay set will begin to flash: Cycle phase under way: During the wash cycle, the LEDs gradually illuminate on to indicate the cycle phase under way: Prewash Wash Rinse Spin cycle Note: during draining, the LED corresponding to the Spin cycle phase will be turned on. As time passes, the remaining delay will be displayed, and the corresponding LED will flash: Function buttons The FUNCTION BUTTONS also act like LEDS. When a function is selected, the corresponding button is illuminated. If the function selected is incompatible with the programme set, the button will flash and the function will not be enabled. If you set a function that is incompatible with another function you selected previously, only the last one selected will be enabled.
Troubleshooting Service Care Precautions
Once the set delay is complete, the flashing LED will turn off and the programme set will start.

Starting and Programmes

Briefly: starting a programme
1. Switch the washing machine on by pressing button. All the LEDS will light up for a few seconds and the ON-OFF/DOOR LOCK Led will begin to flash. 2. Load your laundry into the washing machine, add the detergent and any fabric softener (see page 44) and shut the appliance door. 3. Set the PROGRAMME knob to the programme required. 4. Set the wash temperature (see page 43). 5. Set the spin speed (see page 43). 6. Start he programme by pressing the START/RESET button. To cancel it, keep the START/RESET button pressed for at least 2 seconds. 7. When the programme is finished, the ON-OFF/ DOOR LOCK Led will flash to indicate that the appliance door can be opened. Take out your laundry and leave the appliance door ajar to allow the drum to dry thoroughly. Turn the washing machine off by pressing button.

Programme table

Type of fabric and degree of soi l Pr ogrammes Wash temperat. Detergent Prewash Wash Fabric softener Bleaching Cycle length Description of wash cycle /option (minutes) Bleach

Cotton

Extremely soiled whites (sheets, tablecloths, etc.) Extremely soiled whites (sheets, tablecloths, etc.) Heavily soiled whit es and fast colours Heavily soiled whit es and fast colours Slightly soiled whit es and delicate colours (shirts, jumpers, etc.) 5 90C 90C 60C 40C 30C 137 Pre-wash, wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse crease or delicate Wash cycle, rinse crease or delicate cycles, antispin cycle cycles, antispin cycle
Delicate/ Traditional Delicate/ Traditional Delicate/ Traditional Delicate/ Traditional

129 144

Synthetics
Heavily soiled fast colours (baby linen, etc.) Heavily soiled fast colours (baby linen, etc.) Delicat e colours (all types of slightly soiled garments) Delicat e colours (all types of slightly soiled garments) 60C 50C 40C 30C
Delicate Delicate Delicate
Wash cycle, rinse cycles, anticrease or delicate spin cycle Wash cycle, rinse cycles and delicate spin cycl

Delicate

Wool Very delicate fabrics (curtains, silk, viscose, etc.) PARTIAL PROGRAMMES Rinse Delicat e rinse cycle Spin cycle Delicat e spin cycle Draining 40C 30C
Wash cycle, rinse cycles and delicate spin cycle Wash cycle, rinse cycles, anticrease or draining cycle
Rinse cycles and spin cycle Rinse cycles, anti-crease or draining Draining and heavy duty spin cycle Draining and delicate spin cycle Draining
Notes For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative. Special programme Daily 30' (programme 9 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts 30 minutes and allows you to save on both time and energy. By setting this programme (9 at 30C), you can wash different fabrics together (except for woollen and silk items), with a maximum load of 3 kg. We recommend the use of liquid detergent.

Personalisations

Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 42). The temperature can be lowered, or even set to a cold wash ( ).

Setting the spin speed

Turn the SPIN SPEED knob to set the spin speed for the programme selected. The maximum spin speeds for each programme are as follows: Programmes Maximum spin speed Cottone 800 rpm Synthetics 800 rpm Wool 600 rpm Silk no. The spin speed can be lowered, or the spin cycle can be excluded altogether by selecting symbol The washing machine will automatically prevent you from selecting a spin speed higher than the maximum speed for each programme.

Functions

To enable a function: 1. press the button corresponding to the desired function, according to the table below; 2. the function is enabled when the corresponding button is illuminated. Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the programme set.
Fu n c t i on Delay T i me r
Effect D e l a ys t h e st art of t h e w as h b y u p t o 9 hours
C om m e n t s P es s t h e bu t t o n r e pea t e dl y u n t i l t h e L ED co r r es po n d i n g t o t h e des i r e d de l a y i s t u r n ed o n. T h e f i f t h t i me t h e bu t t o n i s pr es s ed , t h e f u n ct i o n w i l l b e di s a bl ed. N.B.: O n ce yo u h a ve pr es s e d t h e S t a r t / R es et bu t t o n , t h e de l a y ca n o n l y be dec r eas ed i f yo u w i s h t o mo di f y it. T h i s f u n ct i o n i s i n c o mpa t i bl e w i t h t h e R A P I D f u n c t i o n.
E n a b l e d wi t h p r ogr a m m e s: All

S u p er Was h

A l l o w s f o r an i mp ec cab l e w as h , vi s i b l y w h i t er t h an a s t a n d ar d Cl as s A w as h. T h i s o pt i o n r edu c es t h e amo u n t o f cr e as i n g o n f a br i c s , mak i n g t h em ea s i e r t o i r o n.

1, 2, 3, 4, 5, 6, 7, 8

Eas y i r o n
W h e n t h i s f u n c t i o n i s s et , pr o g r ammes 6 , 7 , 8 , an d D e l i c at e r i n s e w i l l en d w i t h t h e l au n dr y l ef t t o s o a k ( A n t i - cr ea s e ) an d t h e R i n s e cyc l e ph as e L ED will f l as h. - t o c o n cl u de t h e c ycl e, pr es s t h e STA R T /R ESET bu t t o n ; - t o r u n t h e d r a i n i n g c ycl e a l o n e, s et t h e k n o b t o t h e r e l at i ve s ymbo l an d p r e s s t h e STA R T /R ES ET bu t t o n. T h i s f u n ct i o n i s i n c o mpa t i bl e w i t h t h e S U P ER W A S H f u n ct i o n.
All p r ogr a m m e s e x c e p t f or 1, 2, 9, 10 and D r a i n i n g.

Troubleshooting Service

Rapi d
Cu t s t h e du r at i o n o f t h e w as h cyc l e by %.
1, 2, 3, 4, 5, 6, 7, 8 Ri n se s

Detergents and laundry

Detergent dispenser
Good washing results also depend on the correct dose of detergent: adding too much detergent won't necessarily make for a more efficient wash, and may in fact cause build up on the interior of your appliance and even pollute the environment. Open up the detergent dispenser and pour in the detergent and fabric softener, as follows.

Preparing your laundry

Divide your laundry according to: - the type of fabric/the symbol on the label. - the colours: separate coloured garments from whites. Empty all pockets and check for loose buttons. Do not exceed the weight limits stated below, which refer to the weight when dry: Sturdy fabrics: max 5 kg Synthetic fabrics: max 2.5 kg Delicate fabrics: max 2 kg Wool: max 1 kg
How much does your laundry weigh?
compartment 1: Detergent for pre-wash compartment 2: Detergent for the wash cycle (powder or liquid) It is recommended that you place liquid detergent directly into the compartment using the appropriate dosing cup. compartment 3: Additives (softener, etc.) When pouring the softener in compartment 3, avoid exceeding the "max" level indicated. The softener is added automatically into the machine during the last wash. At the end of the wash programme, some water will be left in compartment 3. This is used for the inlet of denser fabric softeners into the machine, i.e. to dilute the more concentrated softeners. Should more than a normal amount of water remain in compartment 3, this means the emptying device is blocked. For cleaning instructions, see page 46. compartment 4: Bleach
sheet 400-500 g pillow case 150-200 g tablecloth 400-500 g bathrobe 900-1,200 g towel 150-250 g

Special items

Curtains: fold curtains and place them in a pillow case or mesh bag. Wash them separately without exceeding half the appliance load. Use programme 11 which excludes the spin cycle automatically. Quilted coats and windbreakers: if they are padded with goose or duck down, they can be machine-washed. Turn the garments inside out and load a maximum of 2-3 kg, repeating the rinse cycle once or twice and using the delicate spin cycle. Trainers: remove any mud. They can be washed together with jeans and other tough garments, but not with whites. Wool: for best results, use a specific detergent, taking care not to exceed a load of 1 kg.

Do not use hand wash detergent because it may

form too much foam.

Woolmark Platinum Care
As gentle as a hand wash. Ariston sets a new standard of superior performance that has been endorsed by The Woolmark Company with the prestigious Woolmark Platinum Care brand. Look for the Woolmark Platinum Care logo on the washing machine to ensure you can safely and effectively wash wool garments labelled as "hand wash" (M.0303): Set programme 10 for all "Hand wash" garments, using the appropriate detergent (max load 1 kg).

Bleach cycle

Traditional bleach should be used on sturdy white fabrics, and delicate bleach for coloured fabrics, synthetics and for wool. When pouring in the bleach, be careful not to exceed the "max" level indicated on compartment 4. To run the bleach cycle alone, pour the bleach into (for compartment 4 and set the Rinse programme (for synthetic cotton fabrics) or delicate Rinse fabrics).

Precautions and advice

The washing machine was designed and built in compliance with the applicable international safety regulations. The following information is provided for your safety and should consequently be read carefully.

General safety

This appliance has been designed for nonprofessional, household use and its functions must not be changed. This washing machine should only be used by adults and in accordance with the instructions provided in this manual. Never touch the washing machine when barefoot or with wet or damp hands or feet. Do not pull on the power supply cable to unplug the appliance from the electricity socket. Pull the plug out yourself. Do not open the detergent dispenser while the appliance is in operation. Do not touch the drain water as it could reach very high temperatures. Never force the washing machine door: this could damage the safety lock mechanism designed to prevent any accidental openings. In the event of a malfunction, do not under any circumstances touch internal parts in order to attempt repairs. Always keep children well away from the appliance while in operation. The appliance door tends to get quite hot during the wash cycle. Should it have to be moved, proceed with the help of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy. Before loading your laundry into the washing machine, make sure the drum is empty.

The crossed out "wheeled bin" symbol on the product reminds you of your obligation, that when you dispose of the appliance it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance. Disposing of an old washing machine: before scrapping your appliance, cut the power supply cable and remove the appliance door.

Installation Description

Saving energy and respecting the environment
Environmentally-friendly technology If you only see a little water through your appliance door, this is because thanks to the latest technology, your washing machine only needs less than half the amount of water to get the best results: an objective reached to respect the environment. Saving on detergent, water, energy and time To avoid wasting resources, the washing machine should be used with a full load. A full load instead of two half loads allows you to save up to 50% on energy. The pre-wash cycle is only necessary on extremely soiled garments. Avoiding it will save on detergent, time, water and between 5 and 15% energy. Treating stains with a stain remover or leaving them to soak before washing will cut down the need to wash them at high temperatures. A programme at 60C instead of 90C or one at 40C instead of 60C will save up to 50% on energy. Use the correct quantity of detergent depending on the water hardness, how soiled the garments are and the amount of laundry you have, to avoid wastage and to protect the environment: despite being biodegradable, detergents do contain ingredients that alter the natural balance of the environment. In addition, avoid using fabric softener as much as possible. If you use your washing machine from late in the afternoon until the early hours of the morning, you will help reduce the electricity board's peak load. The Delay Timer option (see page 43 helps to organise your wash cycles accordingly. If your laundry has to be dried in a tumble dryer, select a high spin speed. Having the least water possible in your laundry will save you time and energy in the drying process.
Programmes Detergents Precautions Care Troubleshooting

Disposal

Disposal of old electrical appliances The European Directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimise the recovery and recycling of the materials they contain and reduce the impact on human health and the environment.

Care and maintenance

Cutting off the water or electricity supply
Turn off the water tap after every wash. This will limit the wear of your appliance's water system and also prevent leaks. Unplug your appliance when cleaning it and during all maintenance operations.
Make sure the wash cycle has ended and unplug the appliance.
To recover any objects that have fallen into the prechamber: 1. remove the plinth at the bottom on the front side of the washing machine by pulling from the side with your hands (see diagram); (see figure); 2. unscrew the lid rotating it anticlockwise (see figure): a little water may trickle out. This is perfectly normal; 3. clean the interior thoroughly; 4. screw the lid back on; 5. reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.

Cleaning your appliance

The exterior and rubber parts of your appliance can be cleaned with a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser by raising it and pulling it out (see figure). Wash it under running water; this operation should be repeated frequently.
Caring for your appliance door and drum
Always leave the appliance door ajar to prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning pump that does not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the pre-chamber that protects the pump, situated in the lower part of the same.
Checking the water inlet hose
Check the water inlet hose at least once a year. If you see any cracks, replace it immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open.
Never use hoses that have already been used.
How to clean the detergent dispenser
Disassembly: Press lightly on the large button on the front of the detergent dispenser and pull it upwards (fig. 1). Cleaning: Then clean the dispenser under a tap (fig. 3) using an old toothbrush and, once the pair of siphons inserted in the top of compartments 1 and 2 (fig. 4) have been pulled out, check whether the same are not clogged and then rinse them. Reassembly: Do not forget to reinsert the pair of siphons into the special housings and then to replace the dispenser into its seat, clicking it into place (fig. 4, 2 and 1).
Your washing machine could fail to work. Before calling for Assistance (see page 48), make sure the problem can't easily be solved by consulting the following list.

Problem

The washing machine won't start.
Possible causes/Solution:
The appliance is not plugged into the socket, or not enough to make contact. There has been a power failure. The appliance Lid is not shut properly. The Lid locked Led flashes. button has not been pressed. The The START/RESET button has not been pressed. The water tap is not turned on. A delayed start has been set (using the Delay Timer, see page 43). The water inlet hose is not connected to the tap. The hose is bent. The water tap is not turned on. There is a water shortage. The water pressure is insufficient. The START/RESET button has not been pressed.

The wash cycle won't start.
The washing machine fails to load water.

Programmes

The washing machine continuously loads and unloads water.
The drain hose is not fitted between 65 and 100 cm from the floor (see page 39). The free end of the hose is underwater (see page 39). The wall drainage system doesn't have a breather pipe. If the problem persists even after these checks, turn off the water tap, switch the appliance off and call for Assistance. If the dwelling is on one of the upper floors of a building, there may be drain trap problems causing the washing machine to load and unload water continuously. In order to avoid such an inconvenience, special anti-drain trap valves are available in shops. The programme does not foresee the draining: some programmes require enabling the draining manually (see page 42). The Easy iron option is enabled: to complete the programme, press the START/RESET button (see page 43). The drain hose is bent (see page 39). The drain duct is clogged. When the machine is installed, the locking screws for the oscillating assembly are still in place. Remove the screws (see page 38) The washing machine is not level (see page 38). The washing machine is closed in between furniture cabinets and the wall (see page 38). The water inlet hose is not screwed on correctly (see page 38). The detergent dispenser is obstructed (to clean it, see page 46). The drain hose is not secured properly (see page 39).

Detergents Precautions

The washing machine does not drain or spin.
The washing machine vibrates too much during the spin cycle.
The washing machine leaks.
The ON-OFF/DOOR LOCK Led flashes rapidly at the same time as at least one other LED. There is too much foam.
Call for Assistance because this means there is an abnormality.
The detergent is not suitable for machine washing (it should bear the definition "for washing machines" or "hand and machine wash", or the like). You used too much detergent.
Before calling for Assistance: Check whether you can solve the problem on your own (see page 47); Restart the programme to check whether the problem has been solved; If this is not the case, contact an authorised Technical Service Centre on the telephone number provided on the guarantee certificate.
If the machine has been installed or used incorrectly, you may be charged for the maintenance callout

service.

Always request the assistance of authorised servicemen.
Notify the operator of: the type of problem; the appliance model (Mod.); the serial number (S/N); This information can be found on the data plate situated on the rear of the washing machine.