Instructions for use

WASHING MACHINE Contents

English

Installation, 26-27
Unpacking and levelling, 26 Electric and water connections, 26-27 The first wash cycle, 27 Technical details, 27
Washing machine description, 28-29
Control panel, 28 Leds, 29
Starting and Programmes, 30
Briefly: how to start a programme, 30 Programme table, 30

Personalisations, 31

AVXL 105
Setting the temperature, 31 Setting the spin cycle, 31 Functions, 31 Detergent dispenser, 32 Preparing your laundry, 32 Special items, 32 Cashmere Platinum, 32
Detergents and laundry, 32
Precautions and advice, 33
General safety, 33 Disposal, 33 Saving energy and respecting the environment, 33

Care and maintenance, 34

Cutting off the water or electricity supply, 34 Cleaning your appliance, 34 Cleaning the detergent dispenser, 34 Caring for your appliance door and drum, 34 Cleaning the pump, 34 Checking the water inlet hose, 34
Troubleshooting, 35 Service, 36
Before calling for Assistance, 36

Installation

Keep this instruction manual in a safe place for future reference. Should the appliance be sold, transferred or moved, make sure the instruction manual accompanies the washing machine to inform the new owner as to its operation and features. Read these instructions carefully: they contain vital information on installation, use and safety.
Levelling your appliance correctly will provide it with stability and avoid any vibrations, noise and shifting during operation. If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the washing machine.

Unpacking and levelling

Unpacking
Electric and water connections
Connecting the water inlet hose
1. Unpack the washing machine. 2. Check whether the washing machine has been damaged during transport. If this is the case, do not install it and contact your retailer. 3. Remove the four protective screws and the rubber washer with the respective spacer, situated on the rear of the appliance (see figure).
1. Insert seal A into the end of the inlet hose and screw the latter onto a cold water tap with 3/4 gas theaded mouth (see figure). Before making the connection, allow the water to run freely until it is perfectly clear. 2. Connect the other end of the water inlet hose to the washing machine, screwing it onto the appliance's cold water inlet, situated on the top right-hand side on the rear of the appliance (see figure).
4. Seal the gaps using the plastic plugs provided. 5. Use the plug provided to seal the three holes where the plug was housed, situated on the lower right-hand side on the rear of your appliance. 6. Keep all the parts: you will need them again if the washing machine needs to be moved to another location.
3. Make sure there are no kinks or bends in the hose.
Packaging materials are not children's toys.

Levelling

The water pressure at the tap must be within the
values indicated in the Technical details table (on the next page).
1. Install the washing machine on a flat sturdy floor, without resting it up against walls, furniture cabinets or other. 2. If the floor is not perfectly level, compensate for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured according to the worktop, must not exceed 2.
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
Connecting the drain hose

65 - 100 cm

Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor;
Do not use extensions or multiple sockets.
The power supply cable must never be bent or dangerously compressed. The power supply cable must only be replaced by an authorised serviceman.
Warning! The company denies all liability if and when these norms are not respected.

Description

alternatively, place it over the edge of a basin, sink or tub, fastening the duct supplied to the tap (see figure). The free end of the hose should not be underwater.

The first wash cycle

Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, setting the 90C programme without a pre-wash cycle.

Programmes Detergents

We advise against the use of hose extensions; in case of absolute need, the extension must have the same diameter as the original hose and must not exceed 150 cm in length.

Electric connection

Technical details
Model AVXL 105 59.5 cm wide 85 cm high 56,5 cm deep from 1 to 6 kg voltage 220/230 Volts 60 Hz maximum absorbed power 1850 W maximum pressure 1 MPa (10 bar) minimum pressure 0.05 MPa (0.5 bar) drum capacity 52 litres up to 1000 rpm

Precautions

Before plugging the appliance into the mains socket, make sure that: the socket is earthed and in compliance with the applicable law; the socket is able to sustain the appliance's maximum power load indicated in the Technical details table (on the right); the supply voltage is included within the values i ndicated on the Technical details table (on the right); the socket is compatible with the washing machine's plug. If this is not the case, replace the socket or the plug. outdoor environment, not even when the area is sheltered, because it may be very dangerous to leave it exposed to rain and thunderstorms.
Dimensions Capacity Electric connections Water connections Spin speed Control programmes according to IEC456 directive

Care Troubleshooting

programme 3; temperature 60C; run with a load of 6 kg. This appliance is compliant with the following European Community Directives: - 73/23/CEE of 19/02/73 (Low Voltage) and subsequent amendments - 89/336/CEE of 03/05/89 (Electromagnetic Compatibility) and subsequent amendments
The washing machine should not be installed in an

Service

When the washing machine is installed, the mains socket must be within easy reach.
Washing machine description

Control panel

Leds Programme key

Buttons

FUNCTION START/STOP ON-OFF/DOOR LOCK l

Button

Detergent dispenser

PROGRAMME

START/RESET SPIN SPEED

TEMPERATURE

Detergent dispenser: to add detergent and fabric softener (see page 32). Programme key: to consult a straightforward chart of the different programmes available: pull the grey tab outwards to open it. LEDS: to find out which wash cycle phase is under way. If the Delay Timer function has been set, the time left until the programme starts will be indicated (see page 29). SPIN SPEED knob: to set the spin speed or exclude the spin cycle completely (see page 31). FUNCTION buttons: to select the functions available. The button corresponding to the function selected will remain on.

TEMPERATURE knob: to set the temperature or the cold wash cycle (see page 31). START/STOP button: to turn the washing machine on and off. START/RESET button: to start the programmes or cancel any incorrect settings. ON-OFF/DOOR LOCK Led: to find out whether the washing machine is on and if the appliance door can be opened (see page 29). PROGRAMME knob: to select the wash programmes. The retractable control knob: press the centre of the knob for it to pop out. The knob stays still during the cycle.
The LEDS provide important information. This is what they can tell you: Delay set: If the Delay Timer function has been enabled (see page. 31), once you have started the programme, the LED corresponding to the delay set will begin to flash:
Cycle phase under way: During the wash cycle, the LEDs gradually illuminate on to indicate the cycle phase under way: Prewash Wash Rinse Spin cycle Note: during draining, the LED corresponding to the Spin cycle phase will be turned on. Function buttons The FUNCTION BUTTONS also act like LEDS. When a function is selected, the corresponding button is illuminated. If the function selected is incompatible with the programme set, the button will flash and the function will not be enabled. If you set a function that is incompatible with another function you selected previously, only the last one selected will be enabled.
Installation Description Programmes
As time passes, the remaining delay will be displayed, and the corresponding LED will flash:

Detergents

Once the set delay is complete, the flashing LED will turn off and the programme set will start.
Precautions Care Troubleshooting
ON-OFF/DOOR LOCK led: If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damages, wait for the LED to flash before you open the appliance door.
The rapid flashing of the ON-OFF/DOOR LOCK Led together with the flashing of at least one other LED indicates there is an abnormality. Call for Technical Assistance.

Starting and Programmes

Briefly: starting a programme
1. Switch the washing machine on by pressing button. All the LEDS will light up for a few seconds and the ON-OFF/DOOR LOCK Led will begin to flash. 2. Load your laundry into the washing machine and shut the appliance door. 3. Set the PROGRAMME knob to the programme required. 4. Set the wash temperature (see page 31).

5. Set the spin speed (see page 31). 6. Add the detergent and any fabric softener (see page 32). 7. Start he programme by pressing the START/RESET button. To cancel it, keep the START/RESET button pressed for at least 2 seconds. 8. When the programme is finished, the ON-OFF/ DOOR LOCK Led will flash to indicate that the appliance door can be opened. Take out your laundry and leave the appliance door ajar to allow the drum to dry thoroughly. Turn the washing machine off by pressing button.

Programme table

Type of fabric and degree of Programmes soil Wash temperat. Detergent Prewash Wash Fabric softener Cycle length (minutes) Description of wash cycle

Cotton

Extremely soiled whites (sheets, tablecloths, etc.) Extremely soiled whites (sheets, tablecloths, etc.) Heavily soiled whites and fast colours Heavily soiled whites and fast colours Slightly soiled whites and delicate colours (shirts, jumpers, etc.) 5 90C 90C 60C 40C 40C 72 Pre-wash, wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, anti-crease or delicate spin cycle Wash cycle, rinse cycles, anti-crease or delicate spin cycle Wash cycle, rinse cycles, anti-crease or delicate spin cycle Wash cycle, rinse cycles, anti-crease or delicate spin cycle Wash cycle, rinse cycles and delicate spin cycl Wash cycle, rinse cycles and delicate spin cycle Wash cycle, rinse cycles, anti-crease or draining cycle Rinse cycles and spin cycle Rinse cycles, anti-crease or draining Draining and heavy duty spin cycle Draining and delicate spin cycle Draining

Synthetics

Heavily soiled fast colours (baby linen, etc.) Fast colours (all types of slightly soiled garments) Heavily soiled fast colours (baby linen, etc.) Delicate colours (all types of slightly soiled garments) Delicate colours (all types of slightly soiled garments) 9 60C 40C 50C 40C 30C 30

Delicate

Wool Very delicate fabrics (curtains, silk, viscose, etc.) PARTIAL PROGRAMMES Rinse Delicate rinse cycle Spin cycle Delicate spin cycle Draining 40C 30C
Notes For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative. Special programmes Daily 30' (programme 9 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts 30 minutes and allows you to save on both time and energy. By setting this programme (9 at 30C), you can wash different fabrics together (except for woollen and silk items), with a maximum load of 3 kg. We recommend the use of liquid detergent.

Personalisations

Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Programme table on page 30). The temperature can be lowered, or even set to a cold wash ( ).
Turn the SPIN SPEED knob to set the spin speed for the programme selected. The maximum spin speeds for each programme are as follows: Programmes Maximum spin speed Cottone 1000 rpm Synthetics 800 rpm Wool 600 rpm Silk no. The spin speed can be lowered, or the spin cycle can be excluded altogether by selecting symbol The washing machine will automatically prevent you from selecting a spin speed higher than the maximum speed for each programme.

Setting the spin speed

Description Programmes

Functions

To enable a function: 1. press the button corresponding to the desired function, according to the table below; 2. the function is enabled when the corresponding button is illuminated. Note: The rapid flashing of the button indicates that the corresponding function cannot be selected for the programme set.

Function

Effect Delays the start of the wash by up to 9 hours. Allows for an impeccable wash, visibly whiter than a standard Class A wash. This option reduces the amount of creasing on fabrics, making them easier to iron. Cuts the duration of the wash cycle by 30%.
Comments Press the button repeatedly until the LED corresponding to the desired delay is turned on. The fifth time the button is pressed, the function will be disabled. N.B.: Once you have pressed the Start/Reset button, the delay can only be decreased if you wish to modify it.

Enabled with programmes:

Delay Timer Super Wash
This function is incompatible with the RAPID function.

1, 2, 3, 5, 6, 7, 8.

Easy iron
When this function is set, programmes 6, 7, 8, 11 and Delicate rinse will end with the laundry left to soak (Anti-crease) and the Rinse cycle phase LED will flash. - to conclude the cycle, press the START/RESET button; - to run the draining cycle alone, set the knob to the relative symbol and press the START/RESET button. This function is incompatible with the SUPER WASH function.
All programmes except for 1, 2, 4, 9, 10 and Draining. 1, 2, 3, 5, 6, 7, 8

Troubleshooting

Detergents and laundry
Good washing results also depend on the correct dose of detergent: adding too much detergent won't necessarily make for a more efficient wash, and may in fact cause build up on the interior of your appliance and even pollute the environment. Open up the detergent dispenser and pour in the detergent and fabric softener, as follows.

Special items

Curtains: fold curtains and place them in a pillow case or mesh bag. Wash them separately without exceeding half the appliance load. Use programme 11 which excludes the spin cycle automatically. Quilted coats and windbreakers: if they are padded with goose or duck down, they can be machine-washed. Turn the garments inside out and load a maximum of 2-3 kg, repeating the rinse cycle once or twice and using the delicate spin cycle. Trainers: remove any mud. They can be washed together with jeans and other tough garments, but not with whites. Wool: for best results, use a specific detergent, taking care not to exceed a load of 1,5 kg.

Cashmere Platinum

compartment 1: Detergent for pre-wash (powder) compartment 2: Detergent for the wash cycle (powder or liquid) Liquid detergent should only be poured in immediately prior to the wash cycle start. compartment 3: Additives (fabric softeners, etc.) The fabric softener should not overflow from the grid. As gentle as a hand wash. Ariston sets a new standard of superior performance that has been endorsed by The Woolmark Company with the prestigious Woolmark Platinum Care brand. Look for the Woolmark Platinum Care logo on the washing machine to ensure you can safely and effectively wash wool garments labelled as "hand wash" (M.00221): Set programme 10 for all "Hand wash" garments, using the appropriate detergent.
Do not use hand wash detergent because it may form too much foam.

Preparing your laundry

Divide your laundry according to: - the type of fabric/the symbol on the label. - the colours: separate coloured garments from whites. Empty all pockets and check for loose buttons. Do not exceed the weight limits stated below, which refer to the weight when dry: Sturdy fabrics: max 6 kg Synthetic fabrics: max 2.5 kg Delicate fabrics: max 2 kg Wool: max 1,5 kg
How much does your laundry weigh?
sheet 400-500 g pillow case 150-200 g tablecloth 400-500 g bathrobe 900-1,200 g towel 150-250 g

Precautions and advice

The washing machine was designed and built in compliance with the applicable international safety regulations. The following information is provided for your safety and should consequently be read carefully.

Saving energy and respecting the environment
Environmentally-friendly technology If you only see a little water through your appliance door, this is because thanks to the latest Ariston technology, your washing machine only needs less than half the amount of water to get the best results: an objective reached to respect the environment. Saving on detergent, water, energy and time To avoid wasting resources, the washing machine should be used with a full load. A full load instead of two half loads allows you to save up to 50% on energy. The pre-wash cycle is only necessary on extremely soiled garments. Avoiding it will save on detergent, time, water and between 5 and 15% energy. Treating stains with a stain remover or leaving them to soak before washing will cut down the need to wash them at high temperatures. A programme at 60C instead of 90C or one at 40C instead of 60C will save up to 50% on energy. Use the correct quantity of detergent depending on the water hardness, how soiled the garments are and the amount of laundry you have, to avoid wastage and to protect the environment: despite being biodegradable, detergents do contain ingredients that alter the natural balance of the environment. In addition, avoid using fabric softener as much as possible. If you use your washing machine from late in the afternoon until the early hours of the morning, you will help reduce the electricity board's peak load. The Delay Timer option (see page 31) helps to organise your wash cycles accordingly. If your laundry has to be dried in a tumble dryer, select a high spin speed. Having the least water possible in your laundry will save you time and energy in the drying process.

General safety

This washing machine should only be used by adults and in accordance with the instructions provided in this manual. Never touch the washing machine when barefoot or with wet or damp hands or feet. Do not pull on the power supply cable to unplug the appliance from the electricity socket. Pull the plug out yourself. Do not open the detergent dispenser while the appliance is in operation. Do not touch the drain water as it could reach very high temperatures. Never force the washing machine door: this could damage the safety lock mechanism designed to prevent any accidental openings. In the event of a malfunction, do not under any circumstances touch internal parts in order to attempt repairs. Always keep children well away from the appliance while in operation. The appliance door tends to get quite hot during the wash cycle. Should it have to be moved, proceed with the help of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy. Before loading your laundry into the washing machine, make sure the drum is empty.

Description Programmes Detergents Precautions Care Troubleshooting

Disposal

Disposing of the packaging material: observe local regulations, so the packaging can be re-used. Disposing of an old washing machine: before scrapping your appliance, cut the power supply cable and remove the appliance door.

Care and maintenance

Cutting off the water or electricity supply
Turn off the water tap after every wash. This will limit the wear of your appliance's water system and also prevent leaks. Unplug your appliance when cleaning it and during all maintenance operations.

Cleaning the pump

The washing machine is fitted with a self-cleaning pump that does not require any maintenance. Sometimes, small items (such as coins or buttons) may fall into the pre-chamber that protects the pump, situated in the lower part of the same.
Make sure the wash cycle has ended and unplug the appliance.
To access the pre-chamber: 1. using a screwdriver, remove the cover panel on the lower front of the washing machine (see figure);

Cleaning your appliance

The exterior and rubber parts of your appliance can be cleaned with a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
Remove the dispenser by raising it and pulling it out (see figure). Wash it under running water; this operation should be repeated frequently.
2. unscrew the lid rotating it anticlockwise (see figure): a little water may trickle out. This is perfectly normal;
Caring for your appliance door and drum
Always leave the appliance door ajar to prevent unpleasant odours from forming. 3. clean the interior thoroughly; 4. screw the lid back on; 5. reposition the panel, making sure the hooks are securely in place before you push it onto the appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If you see any cracks, replace it immediately: during the wash cycles, water pressure is very strong and a cracked hose could easily split open.

Never use hoses that have already been used.
Your washing machine could fail to work. Before calling for Assistance (see page 36), make sure the problem can't easily be solved by consulting the following list.

Problem

The washing machine won't start. The wash cycle won't start.
Possible causes/Solution:
The appliance is not plugged into the socket, or not enough to make contact. There has been a power failure. The appliance door is not shut properly. button has not been pressed. The The START/RESET button has not been pressed. The water tap is not turned on. A delayed start has been set (using the Delay Timer, see page 31). The water inlet hose is not connected to the tap. The hose is bent. The water tap is not turned on. There is a water shortage. The water pressure is insufficient. The START/RESET button has not been pressed.
The washing machine fails to load water.

Programmes

The washing machine continuously loads and unloads water.
The drain hose is not fitted between 65 and 100 cm from the floor (see page 27). The free end of the hose is underwater (see page 27). The wall drainage system doesn't have a breather pipe. If the problem persists even after these checks, turn off the water tap, switch the appliance off and call for Assistance. If the dwelling is on one of the upper floors of a building, there may be drain trap problems causing the washing machine to load and unload water continuously. In order to avoid such an inconvenience, special anti-drain trap valves are available in shops. The programme does not foresee the draining: some programmes require enabling the draining manually (see page 30). The Easy iron option is enabled: to complete the programme, press the START/RESET button (see page 31). The drain hose is bent (see page 27). The drain duct is clogged. The drum was not unblocked correctly during installation (see page 26). The washing machine is not level (see page 26). The washing machine is closed in between furniture cabinets and the wall (see page 26). The water inlet hose is not screwed on correctly (see page 26). The detergent dispenser is obstructed (to clean it, see page 34). The drain hose is not secured properly (see page 27). Call for Assistance because this means there is an abnormality.

Detergents Precautions

The washing machine does not drain or spin.
The washing machine vibrates too much during the spin cycle.
The washing machine leaks.
The ON-OFF/DOOR LOCK Led flashes rapidly at the same time as at least one other LED: There is too much foam.
The detergent is not suitable for machine washing (it should bear the definition "for washing machines" or "hand and machine wash", or the like). You used too much detergent.
Before calling for Assistance: Check whether you can solve the problem on your own (see page 35); Restart the programme to check whether the problem has been solved; If this is not the case, contact an authorised Technical Service Centre on the telephone number provided on the guarantee certificate. Always request the assistance of authorised servicemen. Notify the operator of: the type of problem; the appliance model (Mod.); the serial number (S/N); This information can be found on the data plate situated on the rear of the washing machine.

Washing Machine Rebate Program
Eligible Washing Machine List
1 March 2006 - 31 July 2008 - Limit one $150 rebate per dwelling. Rebate only available for machines with a 4-star or 5A water rating or above.
Disclaimer: The information published by Sydney Water is considered to be true and accurate at the time of publication. Whilst all due skill and care has been taken in collecting, validating and providing information, Sydney Water shall not be liable in anyway for loss of any kind including damages, costs, interest, loss of profits or special loss or damage, arising from any error, inaccuracy, incompleteness or other defect in this information. For more information on water ratings and the qualifying products please visit: http://www.wsaa.asn.au http://www.waterrating.gov.au/
L50600 L62800 L86800 L74800 LL1620

WATER RATING

4-STAR 4-STAR 4-STAR 4-STAR 4-STAR Effective 10/01/07 Effective 10/01/07 Effective 22/02/07 Effective 22/02/07 Effective 22/02/07

Ariston

AML 125 AQXL95 AQXXD149H AQXXF129 AQXXL109 AVXL 105 AVXL 129 BS 1400 ET1400
4-STAR 4-STAR 5-STAR 4.5-STAR 4-STAR 4-STAR 4-STAR 5A/4-STAR 4-STAR Effective 10/01/07 Effective 03/05/06 Effective 28/06/06 Effective 17/01/07 Effective 11/10/06 Effective 17/01/07 Effective 06/12/06
4-STAR Effective 12/04/06

23/02/07

W6342 W6441 W6451 W6551 W6761 W6762
4-STAR 5A 4-STAR 5A 5A 4-STAR

Effective 12/04/06

Blanco

5A/4-STAR

WAE 20260AU WAE 22260AU WAE 22460AU WAE 24460AU WAE 26470AU WFO 2460AU WAE 18060AU WAE 24270AU WFR 2830AU WFR 3230AU WFX 2830AU
4-STAR 4-STAR 4-STAR 4-STAR 4-STAR 4-STAR 4-STAR 4-STAR 5A 5A 5A Effective 03/07/06 Effective 27/07/06 Effective 03/07/06 Effective 03/07/06 Effective 03/07/06 Effective 03/07/06 Effective 02/07/06

Daewoo

DWD F1021 DWD F1222

Electrolux

EWF 1087 EWF 1090 EWF 1092 EWF 1495
5A/4-STAR 5A/4-STAR 4-STAR 5A/4 -STAR Effective 27/07/06

Fisher & Paykel

WH60F60W1 (previously AWF60MD) AWF 70MD WH70F60W1 WL80T65CW1
4-STAR 5A 4-STAR 4-STAR Effective 11/10/06 Effective 25/10/06 Effective 05/04/06

HWM 1260K HWM 1270K

5A/4-STAR 4-STAR Effective 01/11/06

Indesit

WI 102 WIDL 106 WIL 102 WIXL 125
4-STAR 4-STAR 4-STAR 4-STAR Effective 30/06/06 Effective 03/05/06 Effective 30/06/06 Effective 03/05/06

Kleenmaid

KFL 1000 KFL 1600
4-STAR 5A/4.5-STAR Effective 03/07/06
WD 1018C WD 1049C WD 1238C WD 1247RD WD 1248RD WD 1255RD WD 1256RD WD 1435RD WD 1438RD WD 1457RD
4-STAR 4-STAR 4-STAR 4-STAR 4-STAR 4.5-STAR 4.5-STAR 5A 4-STAR 4.5-STAR Effective 14/06/06 Effective 20/09/06
Effective 12/04/06 Effective 12/04/06 Effective 12/04/06 Effective 28/06/06 Effective 28/06/06 Effective 15/06/06 Effective 15/06/06
WD 1458RD WD 1485RD WD 1488RD WD 8013C WD 8015C
4.5-STAR 5A 4-STAR 5A 4-STAR

Effective 20/09/06

Effective 14/06/06

Effective 28/06/06

Maytag
MAF 1060AAW MAF 1200AAW MAF 1260AAW MAF 1675AAW
5A/4-STAR 5A 5A 4-STAR Effective 12/04/06
W502 W1213 W2104 W2515 W2653 W2888 WT2670
4-STAR 4-STAR 4-STAR 4-STAR 4-STAR 4-STAR 4-STAR Effective 16/08/06 Effective 23/06/06 Effective 24/05/06 Effective 24/05/06 Effective 24/05/06 Effective 24/05/06 Effective 24/05/06

NFL 1065 NFL 1265

5A/4-STAR 5A

WD9500

4-STAR Effective 06/09/06

Omega (Daewoo)

OW6512WA
4-STAR Effective 07/02/07

Samsung

B1045 B1245 B1245AV J1043 J1045 J1045AV J1055 J1255 J1255AV J1455 J1455AV J843 J845 Q1435V
5A 5A 5A 5A/4-STAR 5A/4-STAR 5A/4-STAR 5A/4-STAR 5A/4-STAR 5A/4-STAR 5A/4-STAR 5A/4-STAR 5A 5A 5A

Simpson

45S708E 45S558E 45S710E
5A 4-STAR 4-STAR Effective 26/06/06 Effective 22/06/06

Technika

TFLE1200 T7E1200FL
5A/4-STAR 4-STAR Effective 21/02/07

TWF-65

Whirlpool
AWO 3561 AWO 5761 WFS 1071AW
5A 5A 4-STAR Effective 29/06/06

WFS 1072AW WFS 1273AW

4-STAR 4-STAR
Effective 29/06/06 Effective 29/06/06