Safety and Environmental Notices Danger Notices
A danger notice calls attention to a situation that is potentially lethal or extremely hazardous to people. Use the following danger notices throughout this book: DANGER To prevent a possible electrical shock during an electrical storm, do not connect or disconnect cables or station protectors for communications lines, display stations, printers, or telephones. (RSFTD003)
DANGER To prevent a possible electrical shock from touching two surfaces with different electrical grounds, use one hand, when possible, to connect or disconnect signal cables. (RSFTD004)
DANGER To prevent a possible electrical shock, do not use the port tester during electrical storms. (RSFTD006)
DANGER An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the system or the products that attach to the system. It is the customers responsibility to ensure that the outlet is correctly wired and grounded to prevent an electrical shock. (RSFTD201)
DANGER To prevent a possible electrical shock when installing the system, ensure that the power cords for all devices are unplugged before installing signal cables. (RSFTD202)
DANGER To prevent a possible electrical shock when adding or removing any devices to or from the system, ensure that the power cords for those devices are unplugged before the signal cables are connected or disconnected. If possible, disconnect all power cords from the existing system before you add or remove a device. (RSFTD203)
DANGER To prevent power from switching on automatically during service procedures, select manual or secure mode on the system unit control panel or disconnect the cables that connect to J15 and J16 on the frame being serviced. (RSFTD211)
DANGER Use caution when installing or modifying telephone lines. Disconnect the lines at the network interface before working with telephone wires that are not insulated. Never install telephone jacks that are not waterproof in wet locations. Do not install or modify telephone lines or use a telephone (other than a cordless type) during an electrical storm. Do not use a telephone to report a gas leak in the area of the leak. (RSFTD213)

TWRCARD 21F5680 The power control compartment is causing an over current condition in the 21F5793 FC 5032 Removable Storage Unit power system. 21F9362 The ac module and the SPCN port cable should be exchanged together.
Detected AC loss Before replacing any parts, verify that the AC input voltage is correct.
PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD CBLALL PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD

1511 1512

Power supply failure Power supply failure

1513 to 1514 1516

Power supply failure No Power Supplies Present The required power supplies are not installed.
Reference Code Description/Action Perform all actions before exchanging Failing Items Power supply failure Power supply failure Failing Item PWRSPLY TWRCARD PWRSPLY TWRCARD CBLALL PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD CBLALL PWRSPLY TWRCARD PWRSPLY TWRCARD PWRREG TWRCARD PWRREG TWRCARD PWRREG TWRCARD PWRREG TWRCARD PWRREG TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD

1523 to 1524 1526

Power Supply P03 fault/AC loss Before replacing any parts, verify that the AC input voltage is correct.

1531 1532

Power Supply P03 fault Power Supply P03 Communication fault

1613, 1623 1810

Power Supply P03 fault Power Supply P03 Fault Regulator Fault on Card Position M01 Regulator Communication Fault on Card Position M01 Regulator Fault on Card Position M01 Regulator Communication Fault on Card Position M01 Regulator Fault on Card Position M01 Load fault on the +12V bus An isolation procedure is required for identifying which load is at fault.
Load fault on the +5V bus An isolation procedure is required for identifying which load is at fault.
Load fault on the +3.3V bus An isolation procedure is required for identifying which load is at fault.
Load fault on the -12V bus An isolation procedure is required for identifying which load is at fault.
Load fault on the +12V bus An isolation procedure is required for identifying which load is at fault.
Reference Code 1B03 Description/Action Perform all actions before exchanging Failing Items Load fault on the +3.3V bus An isolation procedure is required for identifying which load is at fault. 1B04 Load fault on the -12V bus An isolation procedure is required for identifying which load is at fault. 1B05 Load fault on the +1.8V bus An isolation procedure is required for identifying which load is at fault. 1B06 to 1B07 Load fault on the +2.5V bus An isolation procedure is required for identifying which load is at fault. 1B11 Load fault on the +12V bus An isolation procedure is required for identifying which load is at fault. 1B12 Load fault on the +5V bus An isolation procedure is required for identifying which load is at fault. 1B13 1B14 1B16 to 1BLoad fault on the +3.3V bus Load fault on the -12V bus Load fault on the +2.5V bus Power Supply P01 Fault A fault has been detected for Power Supply P01. 2132 Power Supply P02 Fault A fault has been detected for Power Supply P02. 2133 Power Supply P03 Fault A fault has been detected for Power Supply P03. 2134 Power Supply P04 Fault A fault has been detected for Power Supply P04. 2141 Power Supply P01 Fault A fault has been detected for Power Supply P01. 2142 Power Supply P02 Fault A fault has been detected for Power Supply P02. 2143 Power Supply P03 Fault A fault has been detected for Power Supply P03. 2144 Power Supply P04 Fault A fault has been detected for Power Supply P04. 2151 Power Supply P01 Fault A fault has been detected for Power Supply P01. 2152 Power Supply P02 Fault A fault has been detected for Power Supply P02. Failing Item PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWRSPLY SPNLCRD PWRSPLY SPNLCRD PWRSPLY SPNLCRD PWRSPLY SPNLCRD PWRSPLY SPNLCRD PWRSPLY SPNLCRD PWRSPLY SPNLCRD PWRSPLY SPNLCRD PWRSPLY SPNLCRD PWRSPLY SPNLCRD

(1xxx) SPCN Reference Codes for Models 800, 810, and 825
For details on the Failing Item column entries, see the SPCN Failing Items Detail table. Table 1. SPCN reference codes for Models 800, 810, and 825
Reference Code 00A0 Description/Action Perform all actions before exchanging Failing Items SPCN BATs in process No action required. This reference code is logged for information only. If this reference code is present for more than 1 minute, exchange the failing items. Failing Item TWRCARD
Reference Code 00AA Description/Action Perform all actions before exchanging Failing Items Download in process No action required. This reference code is logged for information only. 00AC Detected AC loss If system powers on normally or stays powered on after AC power failure, no replacement of parts may be needed. 00BA The system is running on the Battery Power Unit. No action required. This reference code is displayed for information only. 00BC Battery Power Unit test is in process. No action required. This reference code is displayed for information only. 00CA 00EF 1500 Thermal calibration in progress Remote EPO switch is OFF Detected AC loss Before replacing any parts, verify that the AC input voltage is correct. Power supply failure Power supply failure PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD CBLALL PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD CBLALL PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD CBLALL PWRSPLY TWRCARD ACMODUL Failing Item

1503 1510

Power supply failure Detected AC loss Before replacing any parts, verify that the AC input voltage is correct.

1517 1520

1521 1522

1523 to 1524

Power supply failure
Reference Code 1526 Description/Action Perform all actions before exchanging Failing Items No Power Supplies Present The required power supplies are not installed. Power supply failure Detected AC loss Before replacing any parts, verify that the AC input voltage is correct. Power supply failure Power supply failure Failing Item PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD CBLALL PWRSPLY TWRCARD PWRSPLY TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD PWROC TWRCARD

Reference Code 1313 Description/Action Perform all actions before exchanging Failing Items Regulator R12 Fault A fault has been detected for Regulator R12. 1314 Regulator R13 Fault A fault has been detected for Regulator R13. 1315 Regulator R14 Fault A fault has been detected for Regulator R14. 1316 Regulator R15 Fault A fault has been detected for Regulator R15. 1317 Regulator R16 Fault A fault has been detected for Regulator R16. 1318 Regulator R17 Fault A fault has been detected for Regulator R17. 1319 Regulator R18 Fault A fault has been detected for Regulator R18. 131A Regulator R19 Fault A fault has been detected for Regulator R19. 131B Regulator R20 Fault A fault has been detected for Regulator R20. 131C Regulator R21 Fault A fault has been detected for Regulator R21. 131D Regulator R22 Fault A fault has been detected for Regulator R22. 131E Regulator R23 Fault A fault has been detected for Regulator R23. 1401 3.3V Memory Control 2 Domain Fault A 3.3V Memory 2 Control Domain fault has been detected. 1402 2.5V Memory Control Domain Fault A 2.5V Memory Control Domain fault has been detected. 1403 Cache Regulator Domain Fault A Cache Regulator Domain fault has been detected. 1404 3.3V Memory Control 1 Domain Fault A 3.3V Memory Control 1 Domain fault has been detected. 1405 Processor 1 Regulator Domain Fault A Processor 1 Regulator Domain fault has been detected. 1406 Processor 2 Regulator Domain Fault A Processor 2 Regulator Domain fault has been detected. Failing Item BKSPCN BACKPLN BKSPCN BACKPLN BKSPCN BACKPLN BKSPCN BACKPLN BKSPCN BACKPLN BKSPCN BACKPLN BKSPCN BACKPLN BKSPCN BACKPLN PWRREG BKSPCN PWRREG BKSPCN PWRREG BKSPCN PWRREG BKSPCN DMREG BKSPCN DMREG BKSPCN DMREG BKSPCN DMREG BKSPCN DMREG BKSPCN DMREG BKSPCN
Reference Code 1407 Description/Action Perform all actions before exchanging Failing Items Clock Regulator Domain Fault.A Clock Regulator Domain fault has been detected. 1510 Detected AC loss Before replacing any parts, verify that the AC input voltage is correct. Power supply failure Power supply failure Failing Item DMREG BKSPCN PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD CBLALL PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD CBLALL PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD PWRSPLY TWRCARD CBLALL PWRSPLY TWRCARD PWRREG TWRCARD PWRREG TWRCARD PWRREG TWRCARD PWRREG TWRCARD PWRREG TWRCARD PWRREG TWRCARD

Reference Code 4415 Description/Action Perform all actions before exchanging Failing Items Battery Power Unit missing Failing Item BATRY TWRCARD CBLALL BATCHGR TWRCARD CBLALL AIRMOVR TWRCARD AIRMOVR TWRCARD

8404 to 8406 8409

Air Moving Device Fault Air Moving Device missing error No VPD Found due to Invalid Bypass Timeout on Panel for Request of VPD Unable to Collect VPD VPD Critical Mismatch Processor Unit VPD Mismatch No Processor Installed
AIRMOVR TWRCARD AIRMOVR TWRCARD TWRCARD VPDPART TWRCARD VPDPART TWRCARD VPDPART TWRCARD VPDPART TWRCARD VPDPART TWRCARD
Reference Code 840A 840B 840C 840D 840E 840F 8413 to to Description/Action Perform all actions before exchanging Failing Items VPD 5V Power Off Failure VPD 5V Power On Failure Memory Module Misplug SPCN Configuration mismatch SPCN Default Configuration loaded SPCN Configuration mismatch Invalid Processor VPD No Processor VPD SPCN Configuration mismatch The V/S Comm cable is required, but not connected. 8431 SPCN Configuration mismatch The V/S Comm cable is connected, but not supported by current configuration. 8440 SPCN Configuration mismatch The V/S Comm cable is required, but not connected. 8441 SPCN Configuration mismatch The V/S Comm cable is connected, but not supported by current configuration. to 8801 SPCN Configuration mismatch Capacitor card fault Air Moving Device B01 Not Present Air Moving Device B02 Not Present BPA A AC loss BPA B AC loss BPC A communication failure BPC B communication failure BPC-A and -B are not at standby A DCA or fan has dropped to N-mode status in MCM subsystem BPC download failure on BPA A BPC download failure on BPA B BPC A cable missing BPC B cable missing Failing Item VPDPART TWRCARD VPDPART TWRCARD VPDPART TWRCARD IDPART TWRCARD IDPART TWRCARD IDPART TWRCARD VPDPART TWRCARD VPDPART TWRCARD IDPART TWRCARD IDPART TWRCARD
IDPART CAPPWR AIRMOVR TWRCARD AIRMOVR TWRCARD MAPPWR MAPPWR CBLPWR BPCPWR CBLPWR BPCPWR BPCPWR BPCPWR BPCPWR BPCPWR CBLPWR CBLPWR
Reference Code to 8943 Description/Action Perform all actions before exchanging Failing Items External Netfinity Server 3.3V fault External Netfinity Server Power Good fault Integrated Netfinity Adapter fault External Netfinity Server R485 Communication fault Failing Item ALTMANL TWRCARD TWRCARD ALTMANL TWRCARD TWRCARD CBLALL ALTMANL

Download Initialize Timeout An SPCN node failed to enter the download state after an Initialize for Download command. Exchange the failing SPCN node.
Download Completion Timeout An SPCN node failed to leave the download state. Exchange the failing SPCN node.
Load Damaged Timeout An SPCN node failed to enter the operational state. Exchange the failing SPCN node.
An SPCN LID was not found. No action required. This reference code is logged for information only.
An SPCN microcode download is required. No action required. This reference code is logged for error analysis only.
A status change occured in one of the SPCN nodes. No action required. This reference code is logged for information only.
Licensed Internal Code part number is not correct. The AROS part number field was not updated to the correct level after the system attempted to load new Licensed Internal Code.
Battery Power Unit capacity test failed. The battery power unit was not able to pass the capacity test.
SPCN is too large for VLIC. There are more nodes in the network than VLIC can service.

AJDG301

Primary SPCN node is reporting load damaged. The Licensed Internal Code for the primary SPCN node is damaged. The reload failed because the code could not be found.
Secondary SPCN node is reporting load damaged. The Licensed Internal Code for the secondary SPCN node is damaged. The reload failed because the code could not be found.
Frame SPCN node is reporting load damaged. The Licensed Internal Code for a SPCN node is damaged. The reload failed because the code could not be found.
Reference Code 9115 Description/Action Perform all actions before exchanging Failing Items SPCN Command rejected by the Service Processor. The service processor rejected an SPCN command from the Licensed Internal Code. No action required. This reference code is logged for information only. 9116 SPCN - Control Panel interface failure. The SPCN to control panel interface is not working. 9117 SPCN - Control Panel interface is now working. The SPCN to control panel interface is now working. No action required. This reference code is logged for information only. 91DD 9212 All SPCN Downloads Complete Frame Address field not valid. A Licensed Internal Code command had a frame address that is not valid. Exchange the failing items for the failing node. 9213 Invalid Address status, secondary node. The address in the SPCN command does not match the assigned address of the secondary node. Exchange the failing items for the failing node. 9214 Invalid Address Mode status Invalid Address Mode occurred during Frame Command processing. 9215 Invalid Frame Command status Invalid Frame Command occurred during Frame Command processing. 921B System Unit SPCN Port Fault status. System Unit Port Fault occurred during Command processing. 922B Address Unassigned status A secondary node has no address assigned during Command processing. 9231 Frame-to-Frame Communications Failure A frame-to-frame communications failure occurred during STF processing. 9232 Intrarack Communications Failure An SPCN secondary node to frame communications failure occurred during Command processing. 9233 Intrarack Communications Failure An SPCN frame to secondary node communications failure occurred during Command processing. 9234 Unsupported Packet Size status Unsupported Packet Size occurred during STF and Secondary Node Command processing. TWRCARD AJDG301 TWRCARD AJDG301 TWRCARD AJDG301 TWRCARD AJDG301 TWRCARD CBLALL TWRCARD CBLALL TWRCARD TWRCARD Failing Item

Reference Code 3151 Description/Action Perform all actions before exchanging Failing Items I/O processor detected a SCSI bus configuration error Internal and external SCSI cables are connected to SCSI bus 1 at the same time. Correct the SCSI bus 1 configuration. 3400 I/O processor card detected device error FI02112 STORIOA FI01106 DEVTERM FI01140 DEVBPLN AJDGP01 IOP Failing Item SVCDOCS

3600 to 8009 8012

Device backplane problem I/O processor Licensed Internal Code error System log entry only, no service action required A permanent cache battery pack failure occurred Impending cache battery pack failure Attached read cache devices exceed capacity supported by IOA Reduce the number of read caches on the IOA.
CACHBAT STORIOA CACHBAT SVCDOCS

8100 8130

I/O processor Licensed Internal Code error IOA detected recoverable device bus error An error occurred on SCSI bus 0. No action is required. This reference code is logged for information only.

AJDGP01 IOP

IOA detected recoverable device bus error An error occurred on SCSI bus 1. No action is required. This reference code is logged for information only.
IOA detected recoverable device bus error An error occurred on SCSI bus 2. No action is required. This reference code is logged for information only.
IOA detected recoverable device bus error An error occurred on SCSI bus 3. No action is required. This reference code is logged for information only.
IOA detected recoverable device bus error No action is required. This reference code is logged for information only.
IOA detected recoverable device error No action is required. This reference code is logged for information only.

8155 to 8156

A recoverable I/O processor error occurred. Disk device detected recoverable error A permanent I/O processor failure occurred I/O processor Licensed Internal Code error A permanent I/O processor failure occurred
STORIOA FI01105 STORIOA ANYBRDG AJDGP01 STORIOA AJDGP01 STORIOA
Reference Code 8157 Description/Action Perform all actions before exchanging Failing Items I/O adapter card error Display the Service Action Log entry for this SRC. If the Failing Item indicates I/O adapter, then replace the I/O adapter. If the Failing Item indicates SVCDOCS, then do NOT replace the I/O adapter. This is a recoverable error. Perform the following for the I/O processor that the I/O adapter is attached to: 1. If the I/O Processor is not operable and disk units are attached, use Hardware Service Manager to re-IPL the IOP. Other resources attached to the IOP may then need to be Varied On. 2. If disk units are not attached, perform the VRYCFG RESET(*YES) command to reset the IOP and Vary On attached resources. 9001 I/O processor Licensed Internal Code error I/O processor card detected device error I/O processor card detected device configuration error Perform SDIOP-PIP33. 9002 I/O processor card detected device error Perform SDIOP-PIP16. FI01105 STORIOA FI01140 BACKPLN FI01106 SVCDOCS AJDGP01 IOP FI01105 STORIOA SVCDOCS Failing Item SVCDOCS

(2765, 2766, 2787, 5704) Reference Codes
If the error is reported on the control panel, the unit reference code is characters 5 through 8 of the top 16 character line of function 11. If the error is reported on the console, the unit reference code is the 4 rightmost characters of word 1. Find the unit reference code in the following table.

2765, 2766, 2787, 5704

For more on the Failing Item column entries, see Table 2. Failing Items Details, which follows the reference code table below. Table 1. (2765, 2766, 2787, 5704) Reference Codes
Reference Code 3020 Description/Action Perform all actions before exchanging Failing Items I/O processor detected a configuration error Either too many devices or the wrong kind of devices have been configured under the IOA. Change the configuration. 3100 I/O processor card detected interface error FCINTF ANYFC FCIOA OPT_CLN FCPORT FCIOA FCDEV OPT_CLN Failing Item SVCDOCS
I/O processor detected a port failure
I/O Processor detected that a port is now operational This reference code and the 3120 reference code that occurred before it require no service action, since the port is now operational.
FCDEV FCINTF ANYFC FCIOA OPT_CLN

8130, 8140

Recovered Fibre Channel interface error No action required. This reference code is logged for information only.
IOA detected recoverable device error No action required. This reference code is logged for information only.
A recoverable I/O processor error occurred. Disk device detected recoverable error A permanent I/O processor failure occurred
FCIOA OPT_CLN FCDEV FCIOA ANYBRDG OPT_CLN AJDGP01 FCIOA IOP OPT_CLN AJDGP01 FCIOA OPT_CLN
I/O processor Licensed Internal Code error
A permanent I/O processor failure occurred
Reference Code 9091 to 9092 Description/Action Perform all actions before exchanging Failing Items Incorrect hardware configuration change has been detected. Reset the I/O processor and then IPL the I/O processor. For information on how to reset and IPL the I/O processor, see Debug the Resource in the Hardware Service Manager section of the iSeries Service Functions. If an I/O processor reset and I/O processor IPL does not resolve the problem, contact your next level of support. FF3D Recovered IOA error FCIOA ANYBRDG OPT_CLN Failing Item SVCDOCS

UH7USER MH7TMED UH7CLN FI00871
Failing Item ANYFC DEVTERM FCCABLE FCCODE FCDEV FCGATE FCIOA MH7TMED UH7CLN UH7CNFG UH7USER Description Any device on Fibre Channel interface Terminating plug Fibre Channel cable Gateway device Licensed Internal Code Fibre Channel device Gateway device Fibre Channel IOA Defective tape Tape unit needs cleaning Tape configuration detected by I/O processor; not valid Operator action required Document Description Problem Analysis; Symbolic FRU Isolation Problem Analysis; Symbolic FRU Isolation Problem Analysis; Symbolic FRU Isolation Problem Analysis; Symbolic FRU Isolation Problem Analysis; Symbolic FRU Isolation IBM SAN Data Gateway Service Guide Problem Analysis; Symbolic FRU Isolation Magnetic tape subsystem service information Magnetic tape subsystem operators information Installation System operation information
(6A59) Workstation Adapter Console Reference Codes
The workstation adapter console detected a failure. Look at characters 5 through 8 of the top 16 character line of function 11 (4 rightmost characters of word 1). These 4 characters are the unit reference code. Find the unit reference code in the following table. For more on the Failing Item column entries, see Table 2. Workstation Adapter Console Failing Items Details, which follows the reference code table below. Table 1. (6A59) Workstation Adapter Console Reference Codes
Reference Code 0AD2 to 0AD3 0B25 Description/Action Perform all actions before exchanging Failing Items Communications adapter card test failed Communications adapter card test failed Failing Item FI00718 FI00719 FI00718 FI00727 FI00719 FI00718 FI00719 FI00718 FI00719 FI00718 FI00727 FI00719 FI00718 FI00719 FI00718 FI00719 FI00718 FI00719 FI00718 FI00719 FI00718
0BA0, 0BAB, 0BB0, Communications adapter card test failed 0BD0 to 0BD1 0BEE 0C10 I/O card Licensed Internal Code ended abnormally Communications adapter card test failed
0C20 0C30 0C40, 0C43 0C50, 0C53 0C60, 0C63
Communications adapter card test failed Adapter card failed modem interface test Synchronous-data-link-control send-receive test failed Binary synchronous control send-receive test failed Asynchronous send-receive test failed

I/O processor resource not available The I/O processor error log is being filled faster than the errors are being reported to the system. Check other errors reported to the system and correct them.
FI00131 ANYBUS AJDGP01 AJDG301 FI00131 AJDGP01 AJDG301 AJDGP01 FI00131 AJDGP01 FI00132 FI00131 SVCDOCS

1312 1313

I/O processor card or Licensed Internal Code error

1318 1403

I/O processor card error Service processor Licensed Internal Code error A resource needed to perform a requested function is not available in the Licensed Internal Code.

FI00131 AJDGP01 SVCPROC

Service processor Licensed Internal Code error The Licensed Internal Code has recovered from an unexpected condition.
AJDGP01 SVCPROC AJDGP01 SVCPROC AJDGP01 SVCPROC AJDG301 AJDGP01 SVCPROC AJDG301
Service processor Licensed Internal Code error A recoverable microcode condition occurred on the Service processor.
Service processor Licensed Internal Code failed A microprocessor exception occurred on the Service processor.
Service processor Licensed Internal Code failed The Licensed Internal Code could not allocate resources on the Service processor.
Reference Code 1408 Description/Action Perform all actions before exchanging Failing Items Service processor Licensed Internal Code failed Failing Item AJDGP01 AJDG301 SVCPROC AJDGP01 SVCPROC CDAWKLD FI00130 AJDG301 FI00130 FI00131 FI00132 FI00130 AJDG301 CDAWKLD FI00130 AJDG301 FI00131 FI00132 FI00130 FI00131 FI00132 CDAWKLD FI00132 FI00130 AJDG301 FI00130 FI00131 FI00132 FI00131 FI00132 FI01117 FI00130
Service processor Licensed Internal Code failed The Service processor was not ready for an interrupt that occurred.
I/O processor resource not available A deactivation failed to get a resource controlled by Licensed Internal Code.
Not valid condition in I/O Processor Licensed Internal Code An error in an activation or deactivation occurred.
I/O processor resource not available A resource that is needed to perform a requested function is not available in the Licensed Internal Code.
Recovered from condition in Licensed Internal Code. The Licensed Internal Code has recovered from a condition that was not expected.

1A05 to 1A06

Threshold overflow The I/O processor card has detected a threshold of recoverable error conditions. The errors are either wrong interruptions or memory error corrections. If in communications, the line is still running. Note: If a large number of these errors occur during a short time, they may be caused by an electrically noisy environment, a defective communications I/O processor card or modem, or a communications I/O processor code problem.
Error reported to system The I/O processor error log is being filled faster than the errors are being reported to the system. Check other errors reported to the system and correct them.

Reference Code 0201 Description/Action Perform all actions before exchanging Failing Items WS IOP detected error when transmitting data Perform WSAC-PIP1. 0203 WS IOP detected parity error from device Perform WSAC-PIP1. 0204 Device detected parity error from WS IOP Perform WSAC-PIP1. 0205 WS IOP detected error when transmitting data Perform WSAC-PIP1. 0206 WS IOP detected wrong data from device Perform WSAC-PIP1. 0207 WS IOP detected wrong address from device Perform WSAC-PIP1. 5002 WS IOP detected device power turned off, and then on WS IOP detected wrong device response to start command Printer detected equipment error Device detected not valid value from WS IOP Device detected wrong start command from WS IOP WS IOP detected wrong exception response from device WS IOP detected no status change from device WS IOP detected busy time-out from device Wrong command sent by Licensed Internal Code Procedure error in Licensed Internal Code Procedure error in Licensed Internal Code Procedure error in machine instructions 5009 500A Procedure error in Licensed Internal Code Procedure error in Licensed Internal Code Incorrect command value sent by Licensed Internal Code Procedure error in Licensed Internal Code Failing Item FI00604 GXC7777 FI00631 FI00730 FI00604 GXC7777 FI00631 FI00730 FI00604 GXC7777 FI00631 FI00730 FI00604 GXC7777 FI00631 FI00730 FI00604 FI00631 FI00730 FI00604 GXC7777 FI00730 GXCEEEE FI00604 FI00604 FI00730 FI00604 FI00730 FI00604 FI00730 FI00604 FI00730 FI00604 FI00730 FI00604 FI00730 FI00604 FI00730 AJDG301 AJDG301 CXCTEMP AJDG301 AJDG301 AJDG301 CXCMSTA AJDG301 AJDG301
Reference Code 500D 56EA Description/Action Perform all actions before exchanging Failing Items Incorrect command value sent by Licensed Internal Code Procedure error in Licensed Internal Code Communications controller storage not available Clear-to-send signal dropped on modem interface Failing Item AJDG301 CXCMAXI AJDG301 CXCBUSY GXCLINK FI00704 CXCCTSV FI00719 FI00701 FI00701 FI00704 FI00719 AJLAG01 FI00704 FI00701 GXCLINK FI00719 CXCNPRT FI00700 FI00705 FI00704 GXCLINK FI00701 FI00719 AJLAG01 CXCENCD CXCINAT GXCLINK FI00704 FI00705 FI00700 CXCSTAD FI00701 CXCDTAR FI00719 CXCMRTY GXCLINK CXCRPTO FI00701 FI00704 CXCMRTY FI00705 CXCENCD FI00700 CXCDTAR FI00719 GXCLINK FI00705 FI00704 FI00700 CXCMRTY FI00719 FI00701 FI00700
Data-set-ready turn-on time-out on modem interface
Data-set-ready dropped on modem interface

Nonproductive receive time-out while receiving from remote
No data received from remote equipment; time-out
Remote equipment did not respond causing an idle-time-out
Retry limit reached for sending frames to remote equipment
Reference Code Description/Action Perform all actions before exchanging Failing Items Retry limit reached for sending poll frame to remote Could not send frame to remote equipment; local problem Failing Item FI00700 CXCMODU FI00704 CXCDTAR FI00701 FI00719 FI00730 AJLAG01 CXCSTAD GXCBBBB FI00615

5722 A000 B000

Wrong command value sent by OS/400 licensed program Too many devices active on the workstation IOP WS IOP fails to report part, model and serial number Perform WSAC-PIP1.
C000, D000 D001 F003 FFFF
WS IOP error not known Wrong or no external communications cable installed WS IOA buffer utilization threshold exceeded temporarily User believes there is a problem Reference code FFFF is assigned by the ANZPRB (Analyze Problems) for user-detected errors. Run ANZPRB again if the problem still exists or look in the problem log (WRKPRB) for possible failing FRUs.
AJLAG01 FI00631 AJLAG01 AJLAG01 UXCFF00
Failing Item AJDG301 AJLAG01 CXCBUSY CXCCONF CXCCPTO CXCCTSV CXCDTAR CXCENCD CXCINAT CXCMAXI CXCMODU CXCMRTY CXCMSTA CXCNPRT CXCRPTO CXCSNDT CXCSTAD CXCTEMP Description Vertical Licensed Internal Code Licensed Internal Code Too many communications lines in use Configuration or OS/400 licensed program CNNPOLLTMR value in CRTLINSDLC command CTSTMR value in CRTLINSDLC command LINESPEED value in CRTLINSDLC command NRZI value in CRTLINSDLC command INACTTMR value in CRTLINSDLC command MAXFRAME value in CRTLINSDLC command MODULUS value in CRTLINSDLC command FRAMERTY value in CRTLINSDLC command MAXCTL value in CRTLINSDLC command NPRDRCVTMR value in CRTLINSDLC command IDLTMR value in CRTLINSDLC command SHMNODE value in CRTLINSDLC command STNADR value in CRTCTL_____command No failure found Document Description Service Functions; APAR or LICTR Service Functions; APAR or LICTR Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration Communications Configuration

I/O Port See the Locations Section for the system on which you are working. The HSL I/O Bridge in the base I/O tower may have failed.

RIOPORT

4BF0 to 4BFD 4C03 4C09 4C0A 4C10 to 4C13 4CA5
Mandatory Mandatory Mandatory Mandatory Mandatory Mandatory
I/O Port Processor Card Memory Card I/O Port Configuration Mismatch Configuration Mismatch Check the locations section for the system on which you are working for base system components and processor and memory configuration rules. If the problem is not corrected, contact your next level of support.
RIOPORT ANYPROC ANYMEM CCIN PROCMM NEXTLVL
4CA6 4CA9 4D00 to 4D0F 4EA0 to 4EA2 4EA4 4EAF 4EB0 4EB1 to 4EBC 4EE1 to 4EE2 4EEto 800A to 800D
Mandatory Mandatory Mandatory Mandatory Mandatory Mandatory Mandatory Mandatory Mandatory Mandatory High High High High High
Invalid memory configuration Invalid memory configuration Processor Cache Card Code Error Contact your next level of support Code Error I/O Port I/O Port Code Error Contact your next level of support Clock Card Processor Backplane Processor Card Processor Cache Card Network Interface Controller If this error occurs at IPL time, clean the cable connections (if optical), then reseat the cables. If that does not correct the problem, replace the cable prior to continuing with the FRU list.
NOMSUSE MEMCFG CCIN PROCODE NEXTLVL PROCODE JTPORT PRCLINE PROCODE NEXTLVL PROCODE CCIN CCIN CCIN CCIN CCIN

800E to 800F

Processor Configuration Card
8010 to 801F, 8020 High to 8027, 8100 to 8101, 8110 to 8111, 8120 to 8121 8A03 to 8A06 High
8B00 to 8B03, 8B10 High to 8B17, 8B20 to 8B27, 8B30 to 8B37 8BE0 High
I/O Port See the Locations section for the model on which you are working. The HSL I/O Bridge card in the base I/O tower may have failed.
8BF0 to 8BFD 8C03 8C09 8C0A 8C10 to 8C13 8CA5
High High High High High High
8CA6 8CA9 8D00 to 8D0F 8EA0 to 8EA2 8EA4 8EAF 8EB0 8EB1 to 8EBC 8EE1 to 8EE2 8EE5 C001 C002 C003 to C006 C007 C00A to C00D
High High High High High High High High High High Low Low Low Low Low

C00E to C00F

Reference Code C010 to C01F, C020 to C027, C100 to C101, C110 to C111, C120 to C121 CA03 to CA06 CB00 CB10 CB20 CB30 CBE0 to to to to CB03, CB17, CB27, CB37 Priority Low Description Memory Card Failing Item ANYMEM