Reviews & Opinions
Independent and trusted. Read before buy Asrock 775dual-915GL!

Asrock 775dual-915GL

Manual

Preview of first few manual pages (at low quality). Check before download. Click to enlarge.
Manual - 1 page  Manual - 2 page  Manual - 3 page 

Download (English)
Asrock 775dual-915GL Motherboard, size: 335 KB
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

Asrock 775dual-915GLAbout Asrock 775dual-915GL
Here you can find all about Asrock 775dual-915GL like manual and other informations. For example: review.

Asrock 775dual-915GL manual (user guide) is ready to download for free.

On the bottom of page users can write a review. If you own a Asrock 775dual-915GL please write about it to help other people.

 

[ Report abuse or wrong photo | Share your Asrock 775dual-915GL photo ]

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

Comments to date: 6. Page 1 of 1. Average Rating:
mitternachtsblau 8:40pm on Tuesday, October 26th, 2010 
Note: This review has been rewritten and republishedHere is my review on the refurbished Asrock 775i65G revision 2.0 with bios version 3.
wesyah234 8:37pm on Tuesday, September 28th, 2010 
CAN NOT BEAT ASROCK ASROCK is a brown label of ASUS. I have not had an Asrock board fail me once yet. They are the best bang for the buck.
dsjvicar 4:23pm on Sunday, September 12th, 2010 
installed every thing just fine no problems with install fits the case like a champ very good mobo hope it last me a while none at all Truly a good Mobo, but a pain when starting. Also, it be nice if ASRock gave you a list of the "beep codes" for the Mobo.
saragaska 9:55pm on Monday, June 28th, 2010 
ASrock P45XE Motherboard applies northbridge Intel P45 and southbridge Intel ICH10 chipset.
semimu 11:08pm on Tuesday, June 8th, 2010 
Here is my review on the refurbished Asrock 775i65G revision 2.0 with bios version 3.20 that will work with a 65 nm.
SoftMaker 1:39pm on Thursday, March 25th, 2010 
Great Board & Price If you want a great board for a desktop / office PC this is the one to use.

Comments posted on www.ps2netdrivers.net are solely the views and opinions of the people posting them and do not necessarily reflect the views or opinions of us.

 

Documents

doc0

ASRock 775Dual-915GL Motherboard (Micro ATX Form Factor: 9.6-in x 8.6-in, 24.4 cm x 21.8 cm) ASRock 775Dual-915GL Quick Installation Guide ASRock 775Dual-915GL Support CD (including LGA 775 CPU Installation Live Demo) One 80-conductor Ultra ATA 66/100 IDE Ribbon Cable One Ribbon Cable for a 3.5-in Floppy Drive One Serial ATA (SATA) Data Cable One Serial ATA (SATA) HDD Power Cable (Optional) One ASRock 8CH I/O One COM Port Bracket One ASRock MR Card (Optional)

1.2 Specifications

Micro ATX Form Factor: 9.6-in x 8.6-in, 24.4 cm x 21.8 cm 775-Pin Socket supporting Intel Pentium 4 / Celeron processor (in 775-land LGA package) Chipsets: North Bridge: Intel 915GL chipset, FSB @ 800 / 533MHz, supports Hyper-Threading Technology (see CAUTION 1) South Bridge: Intel ICH6, supports SATA 1.5Gb/s Memory: 2 DDR DIMM slots: DDR1 and DDR2 supports PC3200 (DDR400) / PC2700 (DDR333), Max. 2GB (see CAUTION 2) Dual Channel Memory Technology support(see CAUTION 3) IDE: IDE1: ATA 100 / Ultra DMA Mode 5, supports up to 2 IDE devices Serial ATA: Supports up to 4 SATA devices at 1.5Gb/s data transfer rate. (No Support for RAID and Hot Plug functions) Floppy Port: Supports up to 2 floppy disk drives Audio: 7.1 channels AC97 Audio PCI LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN Hardware Monitor:CPU temperature sensing, Chassis temperature sensing, CPU overheat shutdown to protect CPU life (ASRock U-COP)(see CAUTION 4), CPU fan tachometer, Chassis fan tachometer, Voltage monitoring: +12V, +5V, +3.3V, Vcore PCI slots: 2 PCI slots with PCI Specification 2.3 AMR slot: 1 slot, supports ASRock MR card (Optional) AGI slot: 1 AGI [ASRock Graphics Interface] slot (see CAUTION 5) AGI Express slot (PCI Express x 4): 1 slot with PCI Express x 4 , supports PCI Express x 16 Graphic Card (see CAUTION 6) USB 2.0: 8 USB 2.0 ports: includes 4 default USB 2.0 ports on the rear panel, plus two headers to support 4 additional USB 2.0 ports (see CAUTION 7) ASRock 8CH I/O: 1 PS/2 Mouse Port, 1 PS/2 Keyboard Port 1 VGA Port 1 Parallel Port (ECP/EPP Support) 4 Ready-to-Use USB 2.0 Ports, 1 RJ-45 Port Platform: CPU:

COM Port: BIOS:

Audio Jack: Side Speaker / Rear Speaker / Central/Bass / Line In / Front Speaker / Microphone (see CAUTION 8) 1 COM Port Header to support a COM port module AMI legal BIOS, Supports Plug and Play, ACPI 1.1 compliance wake up events, Supports jumperfree, SMBIOS 2.3.1 support, CPU frequency stepless control (only for advanced users reference, see CAUTION 9) Microsoft Windows 2000 / XP compliant

CAUTION!

1. 2. About the setting of Hyper Threading Technology, please check page 27. Please check the table below for the memory support frequency and its corresponding CPU FSB frequency. CPU FSB Frequency 800 Memory Support Frequency DDR333, DDR400
533 DDR333, DDR400 * This motherboard doesnt support 128Mbit DRAM Cell DIMM (128MB/8 3. cells; 256MB/16 cells; 512MB/32 cells). This motherboard supports Dual Channel Memory Technology. Before you implement Dual Channel Memory Technology, make sure to read the installation guide of memory modules on page 17 for proper installation. 4. While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal 5. grease between the CPU and the heatsink when you install the PC system. The AGI [ASRock Graphics Interface] slot is a special design that only supports compatible AGP VGA cards. For the information of the compatible AGP VGA cards, please refer to the Supported AGP VGA Card List for AGI Slot on page 8 and page 9. For the proper installation of AGP VGA card, please refer to the installation guide on page 18. 6. For the information of the compatible PCI Express VGA cards, please refer to the Supported PCI Express VGA Card List for AGI Express Slot (PCI Express x 4) on page 10. For the proper installation of PCI Express VGA card, please refer to the installation guide on page 18. 7. 8. Power Management for USB 2.0 works fine under Microsoft Windows XP SP1 / 2000 SP4. For microphone input, this motherboard supports both stereo and mono modes. For audio output, this motherboard supports 2-channel, 4-channel, 6-channel, and 8-channel modes. Please check the table on page 12 for proper connection. 9. Although this motherboard offers stepless control, it is not recommended to perform over-clocking. Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU.

Supported AGP VGA Card List for AGI Slot
(for Windows 2000/Windows XP) I. AGP 4X
Graphics Chip Vendor n-VIDIA Model Name ASUS AGP-V8170 ASUS AGP-V9180 Magic INNO3D GeForce4 MX440SE Insignia GeForce MX440SE ATI LEADTEK A170TH GIGABYTE GV-AP64S-H POWERCOLOR RADEON 9100 Transcend TS64MVDR7 For the latest updates of the supported AGP VGA card list for AGI slot, please visit ASRock website for details. ASRock website: http://www.asrock.com/support/index.htm

II. AGP 8X

Graphics Chip Vendor n-VIDIA ASUS AGP-V9570/TD ASUS AGP-V9480 ASUS AGP-V9950ULTRA ASUS AGP-V9520-X ASUS AGP-V9570/TD ASUS V9980 Ultra ASUS V9999 Ultra/2DT ASUS ASUS V9400MAGIC ALBATRON GeForce FX5600 ALBATRON GeForce MX-480 ALBATRON GeForce 6600 Aopen Aeolus Fx5200-DV 128 Awin FX5700-LE ELSA AGP-518BL GIGABYTE GV-N57L256D LEADTEK WinFast A360TD LEADTEK WINFAST A340TDH LEADTEK WinFast A340PRO/TD LEADTEK WinFast A400TDH LEADTEK A6600GT/TDH LEADTEK A280LE TD MIS FX5700-TD128 Prolink PV-N36AX PixeIView PV-N35XA ATI Club 3D RADEON 9800 Connect 3D RADEON 9250 GECUBE RADEON 9250/128M GIGABYTE GV-R9000 PRO GIGABYTE GV-9500 MSI RX 9200 SE-T128 POWERCOLOR RADEON 9200SE POWERCOLOR RADEON 9250/128M For the latest updates of the supported AGP VGA card list for AGI slot, please visit ASRock website for details. ASRock website: http://www.asrock.com/support/index.htm Note. ATi 9600, 9550 series, and all Matrox series VGA cards are NOT supported with AGI. Model Name
Supported PCI Express VGA Card List for AGI Express Slot (PCI Express x 4)
(for Windows 2000/Windows XP)
Graphics Chip Vendor n-VIDIA
Model Name ASUS Extreme N5900 ASUS EN6600 ASUS EN6800 ASUS Extreme N5750/A ALBATRON GeFORCE 6200TC GIGABYTE GV-NX66128D GIGABYTE GV-NX62128D MSI PCX 5750-TD128 SPARKLE GeFORCE 6200TC
Remark (VGA BIOS Version)
ASUS EAX600XT ASUS EAX800XT ASUS EAX300LE-A334C/TD ASUS EAX300LE-A334C R1.01 ASUS EAX300SE/T/N/128M/A R1.01 ASUS EAX700PRO/TVD/256M R1.00 ABIT X600XT ELSA FALCOX X70 PRO 256B3 DTV GIGABYTE GV-RX60P128D BK-ATI VER008.015.117.000 BK-ATI VER008.015.117.000 BK-ATI VER008.015.115.000 AA30602-100 113-xxxxxx-xxx RV410_X9.BIN
For the latest updates of the supported PCI Express VGA card list for AGI Express slot (PCI Express x 4), please visit ASRock website for details. ASRock website: http://www.asrock.com/support/index.htm Note1. Turbo cache PCI Express x 16 VGA cards are not recommanded to use. Note2. If you encounter any compatibility issue when installing above ATi X300 series and X700 series graphics cards, please make sure to update the VGA BIOS version according to the VGA BIOS Information in the table above.

1.5 Motherboard Layout

21.8cm (8.6 in)

PS2 Mouse

1 PS2_USB_PWR1

CPU_FAN1

Prescott 800 FSB800 775Dual-915GL Dual Channel

ATX12V1

DDR400

Super I/O

DDR DIMM1 (64/72 bit, 184-pin module)
DDR DIMM2 (64/72 bit, 184-pin module)

FLOPPY1

PS2 Keyboard

PARALLEL PORT

4Mb BIOS

USB 2.0 T: USB2 B: USB3

ATXPWR1

CHA_FAN1

USB 2.0 T: USB0 B: USB1

Top: RJ-45

AGI EXPRESS

CMOS Battery

CLRCMOS1

EXPRESS

8.015.117.000 8.015.115.000

x RV410_X9.BIN

USB2.0

l te In H6 IC

24.4cm (9.6 in)

8.015.117.000

Bottom: MIC IN Top: LINE IN Center: FRONT

Intel 915GL Chipset

Top: REAR SPK

Bottom: CTR BASS

Center: SIDE SPK

AUDIO CODEC

LAN PHY

AUDIO1

USB45 JR1 JL1

PANEL1

PLED PWRBTN

1 HDLED

1615 14
PS2_USB_PWR1 Jumper ATX 12V Connector (ATX12V1) 775-Pin CPU Socket CPU Fan Connector (CPU_FAN1) 184-pin DDR DIMM Slots (DDR1- 2, Dual Channel) Infrared Module Connector (IR1) BIOS FWH Chip Floppy Connector (FLOPPY1) Primary IDE Connector (IDE1, Black) Chassis Fan Connector (CHA_FAN1) COM Port Header (COM1) South Bridge Controller Chassis Speaker Header (SPEAKER 1) Fourth Serial ATA Connector (SATA4, black) Third Serial ATA Connector (SATA3, black)
Secondary Serial ATA Connector (SATA2, blue) Primary Serial ATA Connector (SATA1, blue) System Panel Header (PANEL1) USB 2.0 Header (USB67, Blue) USB 2.0 Header (USB45, Blue) AMR Slot (AMR1) JR1 / JL1 Jumpers Front Panel Audio Header (AUDIO1) PCI Slots (PCI1- 2) Clear CMOS Jumper (CLRCMOS1) ASRock Graphics Interface Slot (AGI) AGI Express Slot (PCI Express x 4) Internal Audio Connector: CD1 (Black) ATX Power Connector (ATXPWR1) North Bridge Controller

SPEAKER1

ASRock 8CH I/O
Parallel Port RJ-45 Port Side Speaker (Gray) Rear Speaker (Black) Central / Bass (Orange) Line In (Light Blue) Front Speaker (Lime)
Microphone (Pink) USB 2.0 Ports (USB01) USB 2.0 Ports (USB23) VGA Port PS/2 Keyboard Port (Purple) PS/2 Mouse Port (Green)
* If you use 2-channel speaker, please connect the speakers plug into Front Speaker Jack. See
the table below for connection details in accordance with the type of speaker you use.
TABLE for Audio Output Connection
Audio Output Channels Front Speaker Rear Speaker (No. 7) (No. 4) V V V V -V V V Central / Bass (No. 5) --V V Side Speaker (No. 3) ---V

Chapter 2 Installation

775Dual-915GL is a Micro ATX form factor (9.6" x 8.6", 24.4 x 21.8 cm) motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.
Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause physical injuries to you and damages to motherboard components.

2.1 Screw Holes

Place screws into the holes indicated by circles to secure the motherboard to the chassis.
Do not over-tighten the screws! Doing so may damage the motherboard.
2.2 Pre-installation Precautions
Take note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component. 2. To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components. 3. Hold components by the edges and do not touch the ICs. 4. Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component.
Before you install or remove any component, ensure that the power is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.

2.3 CPU Installation

For the installation of Intel 775-LAND CPU, please follow the steps below.

775-Pin Socket Overview

Before you insert the 775-LAND CPU into the socket, please check if the CPU surface is unclean or if there is any bent pin on the socket. Do not force to insert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.
Step 1. Open the socket: Step 1-1. Disengaging the lever by depressing down and out on the hook to clear retention tab.
Step 1-2. Rotate the load lever to fully open position at approximately 135 degrees. Step 1-3. Rotate the load plate to fully open position at approximately 100 degrees. Step 2. Insert the 775-LAND CPU: Step 2-1. Hold the CPU by the edges where are marked with black lines.

black line

Step 2-2. Orient the CPU with IHS (Integrated Heat Sink) up. Locate Pin1 and the two orientation key notches.
Pin1 orientation key notch orientation key notch Pin1 alignment key alignment key
775-Pin Socket 775-LAND CPU

For proper inserting, please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket.
Step 2-3. Carefully place the CPU into the socket by using a purely vertical motion. Step 2-4. Verify that the CPU is within the socket and properly mated to the orient keys. Step 3. Remove PnP Cap (Pick and Place Cap): Use your left hand index finger and thumb to support the load plate edge, engage PnP cap with right hand thumb and peel the cap from the socket while pressing on center of PnP cap to assist in removal.
It is recommended to use the cap tab to handle and avoid kicking off the PnP cap.
Step 4. Close the socket: Step 4-1. Rotate the load plate onto the IHS. Step 4-2. While pressing down lightly on load plate, engage the load lever. Step 4-3. Secure load lever with load plate tab under retention tab of load lever.
Installation of CPU Fan and Heatsink
This motherboard is equipped with 775-Pin socket that supports Intel 775-LAND CPU. Please adopt the type of heatsink and cooling fan compliant with Intel 775-LAND CPU to dissipate heat. Before you installed the heatsink, you need to spray thermal interface material between the CPU and the heatsink to improve heat dissipation. Ensure that the CPU and the heatsink are securely fastened and in good contact with each other. Then connect the CPU fan to the CPU_FAN connector (CPU_FAN1, see page 11, No. 4). For proper installation, please kindly refer to the instruction manuals of your CPU fan and heatsink. Below is an example to illustrate the installation of the heatsink for 775-LAND CPU. Step 1. Apply thermal interface material onto center of IHS on the socket surface.

Step 2.

Step 3. Step 4.
Place the heatsink onto the socket. Ensure fan cables are oriented on side closest to the CPU fan connector on the motherboard (CPU_FAN1, see page 11, No. 4). Align fasteners with the motherboard throughholes. Rotate the fastener clockwise, then press down on fastener caps with thumb to install and lock. Repeat with remaining fasteners.
If you press down the fasteners without rotating them clockwise, the heatsink cannot be secured on the motherboard.

Step 5. Step 6.

Connect fan header with the CPU fan connector on the motherboard. Secure excess cable with tie-wrap to ensure cable does not interfere with fan operation or contact other components.

2.5 Installation of Memory Modules (DIMM)
775Dual-915GL motherboard provides two 184-pin DDR (Double Data Rate) DIMM slots, and supports Dual Channel Memory Technology. For dual channel configuration, you always need to install two identical (the same brand, speed, size and chip-type) memory modules in the DDR DIMM slots to activate Dual Channel Memory Technology. Otherwise, it will operate at single channel mode.
If you install only one memory module or two non-identical memory modules, it is unable to activate the Dual Channel Memory Technology.

Installing a DIMM

Please make sure to disconnect power supply before adding or removing DIMMs or the system components.

Step 1. Step 2.

Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.

notch break

The DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

Step 3.

Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated.
2.6 Expansion Slots (PCI, AMR, AGI, and AGI Express Slots)
There are 2 PCI slots, 1 AMR slot, 1 AGI slot, and 1 AGI Express slot (PCI Express x 4) on this motherboard. PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI interface. AMR slot: AMR slot is used to insert an ASRock MR card (optional) with v.92 Modem functionality. AGI slot: The AGI [ASRock Graphics Interface] slot is a special design that only supports compatible AGP VGA cards. For the information of the compatible AGP VGA cards, please refer to the Supported AGP VGA Cards List for AGI Slot on page 8 and page 9. AGI Express slot (PCI Express x 4): AGI Express slot (PCI Express x 4) is used to install PCI Express expansion cards. For the information of the compatible PCI Express VGA cards, please refer to the Supported PCI Express VGA Card List for AGI Express Slot (PCI Express x 4) on page 10.
1. If you install the add-on AGP VGA card or PCI Express VGA card, BIOS setup will automatically disable the onboard VGA. 2. Please make sure to set the BIOS onboard VGA selection into En abled if you want this motherboard to support Surround Display. Then the onboard VGA in Windows will be the primary VGA card.

2.9 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

FDD connector

(33-pin FLOPPY1) (see p.11 No. 8)

Pin1 FLOPPY1

the red-striped side to Pin1
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE connector (Black)
(39-pin IDE1, see p.11 No. 9)
connect the black end connect the blue end to the IDE devices to the motherboard 80-conductor ATA 66/100 cable Note: Please refer to the instruction of your IDE device vendor for the details.

Serial ATA Connectors

(SATA1: see p.11 No. 17) (SATA2: see p.11 No. 16) (SATA3: see p.11 No. 15) (SATA4: see p.11 No. 14)

SATA1 SATA2 SATA3 SATA4

These four Serial ATA (SATA) connectors support SATA data cables for internal storage devices. The current SATA interface allows up to 1.5 Gb/s data transfer rate. Either end of the SATA data cable can be connected to the SATA hard disk or the SATA connector on the motherboard.
Serial ATA (SATA) Data Cable
Serial ATA (SATA) Power Cable

(Optional)

connect to the SATA HDD power connector connect to the power supply
Please connect the black end of SATA power cable to the power connector on each drive. Then connect the white end of SATA power cable to the power connector of the power supply. ASRock 8CH I/O accommodates 4 default USB 2.0 ports. If those USB 2.0 ports on the I/O panel are not sufficient, this USB 2.0 header is available to support 2 additional USB 2.0 ports. ASRock 8CH I/O accommo-

USB 2.0 Header

(9-pin USB67) (see p.11 No. 19)
USB_PWR P-6 P+6 GND DUMMY

GND P+7 P-7 USB_PWR

(9-pin USB45) (see p.11 No. 20)
1 GND P+4 P-4 USB_PWR USB_PWR P-5 P+5 GND DUMMY
dates 4 default USB 2.0 ports. If those USB 2.0 ports on the I/O panel are not sufficient, this USB 2.0 header is available to support 2 additional USB 2.0 ports. This header supports an optional wireless transmitting and receiving infrared module. These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for front panel audio cable that allows convenient connection and control of audio devices.

Infrared Module Header

(5-pin IR1) (see p.11 No. 6)

IRTX +5V DUMMY

GND IRRX
Internal Audio Connectors
(4-pin CD1) (CD1: see p.11 No. 28)

CD-R GND GND CD-L

Front Panel Audio Header
(9-pin AUDIO1) (see p.11 No. 23)
1 AUD-OUT-L GND AUD-OUT-R MIC-POWER MIC GND +5VA BACKOUT-R BACKOUT-L

System Panel Header

(9-pin PANEL1) (see p.11 No. 18)

PLED+ PLEDPWRBTN# GND

This header accommodates several system front panel functions.
DUMMY RESET# GND HDLEDHDLED+

Chassis Speaker Header

(4-pin SPEAKER 1) (see p.11 No. 13)

SPEAKER DUMMY DUMMY +5V

Please connect the chassis speaker to this header.

Chassis Fan Connector

(3-pin CHA_FAN1) (see p.11 No. 10)

GND +12V CHA_FAN_SPEED

Please connect a chassis fan cable to this connector and match the black wire to the ground pin. Please connect a CPU fan cable to this connector and match the black wire to the ground pin. Please connect an ATX power supply to this connector.

CPU Fan Connector

(4-pin CPU_FAN1) (see p.11 No. 4)
GND +12V CPU_FAN_SPEED N/C

ATX Power Connector

(20-pin ATXPWR1) (see p.11 No. 29)

COM Port Header

(9-pin COM1) (see p.11 No. 11)
RRXD1 DDTR#1 DDSR#1 CCTS#1
This COM port header is used to support a COM port module.
RRI#1 RRTS#1 GND TTXD1 DDCD#1

ATX 12V Connector

(4-pin ATX12V1) (see p.11 No. 2)
Please connect an ATX 12V power supply to this connector.
AT (SAT 2.10 Serial ATA (SATA) Hard Disks Installation
This motherboard adopts Intel ICH6 south bridge chipset that supports Serial ATA (SATA) hard disks. You may install SATA hard disks on this motherboard for internal storage devices. This section will guide you to install the SATA hard disks. STEP 1: Install the SATA hard disks into the drive bays of your chassis. STEP 2: Connect the SATA power cable to the SATA hard disk. STEP 3: Connect one end of the SATA data cable to the motherboards SATA connector. STEP 4: Connect the other end of the SATA data cable to the SATA hard disk.
Before you install OS into the SATA hard disk, you need to check and ensure the configuration of the OnBoard IDE Operate Mode option in BIOS setup is correct according to the condition of your system. For the configuration details, please refer to the instruction on page 30.
Chapter 3 BIOS SETUP UTILITY

3.1 Introduction

This section explains how to use the BIOS SETUP UTILITY to configure your system. The BIOS FWH chip on the motherboard stores the BIOS SETUP UTILITY. You may run the BIOS SETUP UTILITY when you start up the computer. Please press <F2> during the Power-On-Self-Test (POST) to enter the BIOS SETUP UTILITY, otherwise, POST will continue with its test routines. If you wish to enter the BIOS SETUP UTILITY after POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. You may also restart by turning the system off and then back on. Because the BIOS software is constantly being updated, the following BIOS setup screens and descriptions are for reference purpose only, and they may not exactly match what you see on your screen.

3.1.1 BIOS Menu Bar

The top of the Main Advanced H/W Monitor Boot screen has a menu bar with the following selections: To set up the system time/date information To set up the advanced BIOS features To display current hardware status To set up the default system device to locate and load the Operating System Security To set up the security features Exit To exit the current screen or the BIOS SETUP UTILITY Use < > key or < > key to choose among the selections on the menu bar, and then press <Enter> to get into the sub screen.

3.1.2 Navigation Keys

Please check the following table for the function description of each navigation key. Navigation Key(s) / / + / <Enter> <F1> <F9> <F10> <ESC> Function Description Moves cursor left or right to select Screens Moves cursor up or down to select items To change option for the selected items To bring up the selected screen To display the General Help Screen To load optimal default values for all the settings To save changes and exit the BIOS SETUP UTILITY To jump to the Exit Screen or exit the current screen

3.2 Main Screen

When you enter the BIOS SETUP UTILITY, the Main screen will appear and display the system overview
BIOS SETUP UTILITY H/W Monitor Boot

Advanced

Security

System Overview

System Time System Date BIOS Version Processor Type Processor Speed Microcode Update Cache Size Total Memory DIMM 1 DIMM 2 : : : : : [14:00:09] [Wed 01/05/2005] 775Dual-915GL BIOS P1.00 Intel (R) CPU 2.40 GHz 2400 Mhz F24/1E 512KB
Use [Enter], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system Time.
: 512MB with 8MB shared memory Dual-Channel Memory Mode : 256MB/166MHz (DDR333) : 256MB/166MHz (DDR333)

+Tab F1 F9 F10 ESC

Select Screen Select Item Change Field Select Field General Help Load Defaults Save and Exit Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
System Time [Hour:Minute:Second] Use this item to specify the system time. System Date [Day Month/Date/Year] Use this item to specify the system date.

3.3 Advanced Screen

3.3.3 ACPI Configuration

BIOS SETUP UTILITY Advanced ACPI Configuration
Suspend To RAM Restore on AC/Power Loss Ring-In Power On PCI Devices Power On PS / 2 Keyboard Power On RTC Alarm Power On [Disabled] [Power Off] [Disabled] [Disabled] [Disabled] [Disabled] Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit Select auto-detect or disable the STR feature.
Restore on AC/Power Loss This allows you to set the power state after an unexpected AC/ Power loss. If [Power Off] is selected, the AC/Power remains off when the power recovers. If [Power On] is selected, the AC/Power resumes and the system starts to boot up when the power recovers. Ring-In Power On Use this item to enable or disable Ring-In signals to turn on the system from the power-soft-off mode. PCI Devices Power On Use this item to enable or disable PCI devices to turn on the system from the power-soft-off mode.
PS/2 Keyboard Power On Use this item to enable or disable PS/2 keyboard to turn on the system from the power-soft-off mode. RTC Alarm Power On Use this item to enable or disable RTC (Real Time Clock) to power on the system.

3.3.4 IDE Configuration

BIOS SETUP UTILITY Advanced IDE Configuration
ATA/IDE Configuration SATA1 SATA2 SATA3 SATA4 IDE1 Master IDE1 Slave [Enhanced] [Hard Disk] [Not Detected] [Not Detected] [Not Detected] [ATAPI CDROM] [Not Detected] Set [Compatible] when Legacy OS (MS-DOS, Win NT) device is used. Set [Enhanced] when Native OS (Win2000 / XP) is used.
Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit
ATA/IDE Configuration Please select [Compatible] when you install legacy OS (Windows NT). If native OS (Windows 2000 / XP) is installed, please select [Enhanced]. When [Compatible] is selected Combined Option It allows you to select between [SATA 1, SATA 2, SATA 3, SATA 4], [SATA 1, SATA 3, IDE 1], and [IDE 1, SATA 2, SATA 4]. If it is set to [SATA 1, SATA 3, IDE 1], then SATA2, SATA4 will not work. Likewise, if it is set to [IDE 1, SATA 2, SATA 4], then SATA1, SATA3 will not work.
Because Intel ICH6 south bridge only supports four IDE devices under legacy OS (Windows NT), you have to choose [SATA 1, SATA 2, SATA 3, SATA 4], [SATA 1, SATA 3, IDE 1], or [IDE 1, SATA 2, SATA 4] when the installed device is used with legacy OS. [SATA 1, SATA 2, SATA 3, SATA 4] Master Slave SATA1, SATA2, SATA3, SATA4, [SATA 1, SATA 3, IDE 1] SATA1 SATA3 [IDE 1, SATA 2, SATA 4] SATA2 SATA4

IDE Device Configuration You may set the IDE configuration for the device that you specify. We will use the Primary IDE Master as the example in the following instruction.
BIOS SETUP UTILITY Advanced Primary IDE Master
Device Vendor Size LBA Mode Block Mode PIO Mode Async DMA Ultra DMA S.M.A.R.T. Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T. 32Bit Data Transfer :Hard Disk :ST340014A :40.0 GB :Supported :16Sectors :4 :MultiWord DMA-2 :Ultra DMA-5 :Supported [Auto] [Auto] [Auto] [Auto] [Auto] [Disabled] [Enabled]
Select the type of device connected to the system.
TYPE Use this item to configure the type of the IDE device that you specify. Configuration options: [Not Installed], [Auto], [CD/DVD], and [ARMD]. [Not Installed]: Select [Not Installed] to disable the use of IDE device. [Auto]: Select [Auto] to automatically detect the hard disk drive. After selecting the hard disk information into BIOS, use a disk utility, such as FDISK, to partition and format the new IDE hard disk drives. This is necessary so that you can write or read data from the hard disk. Make sure to set the partition of the Primary IDE hard disk drives to active. [CD/DVD]: This is used for IDE CD/DVD drives. [ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device), such as MO. LBA/Large Mode Use this item to select the LBA/Large mode for a hard disk > 512 MB under DOS and Windows; for Netware and UNIX user, select [Disabled] to disable the LBA/Large mode.
Block (Multi-Sector Transfer) The default value of this item is [Auto]. If this feature is enabled, it will enhance hard disk performance by reading or writing more data during each transfer. PIO Mode Use this item to set the PIO mode to enhance hard disk performance by optimizing the hard disk timing. DMA Mode DMA capability allows the improved transfer-speed and data-integrity for compatible IDE devices. S.M.A.R.T. Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) feature. Configuration options: [Disabled], [Auto], [Enabled]. 32-Bit Data Transfer Use this item to enable 32-bit access to maximize the IDE hard disk data transfer rate.
3.3.5 PCIPnP Configuration
BIOS SETUP UTILITY Advanced PCI / PnP Configuration
WARNING: Setting wrong values in below actions may cause system to malfunction. PCI Latency Timer PCI IDE BusMaster [32] [Enabled] Value in units of PCI clocks for PCI device latency timer register.

 

Tags

Rs 800 Cf900 MB-387W 42PF7421 TM-U675 G W KV-V1430K LA32R81B SP-J720K X1100 BH-200 Xbox 360 2 7 AST-S1 Donky Kong GR-S462GC MX-4500N IC-A22 RH387H 33csptn01 Scales VGN-FS215E Maxi-cosi Tobi Induction OW5023 C-350 Zoom RQ-SX71 NV-GS35EG Portrait STR-DE525 321 II FVX538V2 Pqnfb17B0 GB801 Reference HS 200 MX-980 41283 Docucolor 8000 XS-LB12S MA351 VGN-NS31m S T37850 460DX NEC LT80 Pilot III Conquest Game MP-233 TY-FB7TA MZ-RH1 Dm220 Serie 2000 Deluxe HT-DS490 NV-GS230EG LC37A1E E-300L N4060W CMT-ED1A VSX-D709S SCL901 KX-P7105 Pixon BR-6218MG Ducati 695 VSX-AX5ai-G Plus M-10 Hdci-5000 Motorola T720 Knukles 370DE6 RX-D29 VGN-NS21z S 1923H Mini 2102 2100M LMV1630WW DVD 29 WV-PS15 SD-P1600 Guide Virus KB Review DP391B Chronographs MHC-EC68USB TCP65S2 PW50-1998 FS-85USB Samsung S843 CD1013 SR-270II T7300 21T9D PET700 PDK-TS23 DVD-V8000 5100-503 Zentera DDW1805W Gz-mg505

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101