1.1 Package Contents

ASRock P4V88 Motherboard (ATX Form Factor: 12.0-in x 8.6-in, 30.5 cm x 21.8 cm) ASRock P4V88 Quick Installation Guide ASRock P4V88 Support CD One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable One Ribbon Cable for a 3.5-in Floppy Drive One Serial ATA (SATA) Cable One Serial ATA (SATA) HDD Power Cable(Optional) One ASRock I/O PlusTM Shield

1.2 Specifications

Platform: CPU: Chipsets: ATX Form Factor: 12.0-in x 8.6-in, 30.5 cm x 21.8 cm Socket 478, supports Intel Pentium 4 (Prescott, Northwood,
Willimate) / Celeron processor North Bridge: VIA PT880, FSB @ 800/533/400 MHz, with Intel Hyper-Threading Technology ready (see CAUTION 1) South Bridge: VIA VT8237, supports USB 2.0, ATA 133, SATA 1.5Gb/s Memory: 4 DDR DIMM Slots: DDR1, DDR2, DDR3, and DDRDDR DIMM Slots Supports PC3200 (DDR400), Max. 2GB, 4 DDR DIMM Slots Supports PC2700 (DDR333) / PC2100 (DDR266), Max. 3.5GB, Dual Channel Memory Technology support (see CAUTION 2) IDE: IDE1: ATA 133 / Ultra DMA Mode 6 IDE2: ATA 133 / Ultra DMA Mode 6 Supports up to 4 IDE devices Serial ATA: 2 SATA connectors Support up to 1.5Gb/s data transfer rate Floppy Port: Supports up to 2 floppy disk drives Audio: 5.1 channels AC97 Audio LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN Hardware Monitor: CPU temperature sensing Chassis temperature sensing CPU overheat shutdown to protect CPU life (ASRock U-COP)(see CAUTION 3) CPU fan tachometer Chassis fan tachometer Voltage monitoring: +12V, +5V, +3V, Vcore PCI slots: 5 slots with PCI Specification 2.2 AGP slot: 1 AGP slot, supports 1.5V, 8X/4X AGP card (see CAUTION 4) USB 2.0: 8 USB 2.0 ports: include 6 ready-to-use USB 2.0 ports on the rear panel, plus one on-board header supporting 2 extra USB 2.0 ports (see CAUTION 5)
ASRock I/O PlusTM: 1 PS/2 mouse port, 1 PS/2 keyboard port, 1 serial port: COM1, 1 parallel port: ECP/EPP support, 6 ready-to-use USB 2.0 ports, 1 RJ 45 port, Audio Jack: Line In / Line Out / Microphone BIOS: AMI BIOS Supports Plug and Play ACPI 1.1 compliance wake up events Supports jumperfree SMBIOS 2.3.1 support CPU frequency stepless control (only for advanced users reference, see CAUTION 6) OS: Microsoft Windows 98SE / ME / 2000 / XP compliant

CAUTION!

1. 2. About the setting of Hyper Threading Technology, please check page 24. This motherboard supports Dual Channel Memory Technology. Before you implement Dual Channel Memory Technology, make sure to read the installation guide of memory modules on page 12 for proper installation. 3. While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal 4. 5. grease between the CPU and the heatsink when you install the PC system. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard! It may cause permanent damage! Power Management for USB 2.0 works fine under Microsoft Windows XP SP1 / 2000 SP4. It may not work properly under Microsoft Windows 98 / ME. Please refer to Microsoft official document at 6. http://www.microsoft.com/whdc/hwdev/bus/USB/USB2support.mspx Although this motherboard offers stepless control, it is not recommended to perform over-clocking. Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU.

1.3 Motherboard Layout

3 21.8cm (8.6 in)

PS2 Mouse

PS2_USB_PWR1 CPU_FAN1

ATX12V1

PARALLEL PORT

PS2 Keyboard

PGA478
DDR3 (64/72 bit, 184-pin module) DDR1 (64/72 bit, 184-pin module)
DDR4 (64/72 bit, 184-pin module)
DDR2 (64/72 bit, 184-pin module)

USB 2.0 T: USB2 B: USB3

USB 2.0 Top: T: USB0 RJ-45 B: USB1

USB 2.0 T: USBB: USB5

USB4_5

ATXPWR1

P VIA T hi 88 ps 0 et

AGP 8X

30.5cm (12.0 in)

Super I/O

Top: Line In Center: Line Out Bottom: Mic In

AUDIO1

JL1 JR1

Audio CODEC

LAN PHY

1.5V_AGP1

USB2.0

FSB800 DDR400

CMOS Battery

VIA VT8237

2MB BIOS

5.1 CH

CLRCMOS1

PCI 4 ATA133

FLOPPY1

CHA_FAN1 SPEAKER1

PANEL 1

PLED PWRBTN

1 HDLED RESET
PS2_USB_PWR1 Jumper CPU Fan Connector (CPU_FAN1) CPU Heatsink Retention Module CPU Socket North Bridge Controller 2 x 184-pin DDR DIMM Slots (Dual Channel A: DDR1, DDR3; Blue) ATX 12V Connector (ATX12V1) Secondary IDE Connector (IDE2, Black) Primary IDE Connector (IDE1, Blue) 2 x 184-pin DDR DIMM Slots (Dual Channel B: DDR2, DDR4; Black) AGP Slot (1.5V_AGP1) Secondary Serial ATA Connector (SATA2) Primary Serial ATA Connector (SATA1) South Bridge Controller Clear CMOS Jumper (CLRCMOS1)
Floppy Connector (FLOPPY1) System Panel Header (PANEL1) Chassis Speaker Header (SPEAKER 1) Chassis Fan Connector (CHA_FAN1) USB 2.0 Header (USB67, Blue) Infrared Module Header (IR1) Game Connector (GAME1) 5 x PCI Slots (PCI1- 5) Flash Memory JL1 Jumper JR1 Jumper Front Panel Audio Header (AUDIO1) Internal Audio Connector: AUX1 (White) Internal Audio Connector: CD1 (Black) Shared USB 2.0 Header (USB4_5, Blue) ATX Power Connector (ATXPWR1)

1.4 ASRock I/O Plus TM

Parallel Port RJ-45 Port Line In (Light Blue) Line Out (Lime) Microphone (Pink) 2 x Shared USB 2.0 Ports (USB4, USB5)
2 x USB 2.0 Ports (USB0, USB1) 2 x USB 2.0 Ports (USB2, USB3) Serial Port: COM1 PS/2 Keyboard Port (Purple) PS/2 Mouse Port (Green)

2. Installation

P4V88 is an ATX form factor (12.0-in x 8.6-in, 30.5 cm x 21.8 cm) motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component. 2. To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components. 3. Hold components by the edges and do not touch the ICs. 4. Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component.

Before you install or remove any component, ensure that the power is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.

2.1 CPU Installation

Step 1. Step 2. Step 3. Unlock the socket by lifting the lever up to a 90 angle. Position the CPU directly above the socket such that its marked corner matches the base of the socket lever. Carefully insert the CPU into the socket until it fits in place.
The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to avoid bending of the pins.

Step 4.

When the CPU is in place, press it firmly on the socket while you push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked.
CPU Marked Corner Lift Lever Up to 90 Socket Marked Corner
STEP 1: Lift The Socket Lever Up to 90
STEP 2/STEP 3: Match The CPU Marked Corner to The Socket Marked Corner
STEP 4: Push Down And Lock The Socket Lever
2.2 Installation of CPU Fan and Heatsink
This motherboard adopts 478-pin CPU socket to support Intel Pentium 4 / Celeron CPU. It requires larger heatsink and cooling fan to dissipate heat. You also need to spray thermal grease between the CPU and the heatsink to improve heat dissipation. Make sure that the CPU and the heatsink are securely fastened and in good contact with each other. Then connect the CPU fan to the CPU_FAN connector (CPU_FAN1, see p.8 No. 2). For proper installation, please kindly refer to the instruction manuals of the CPU fan and the heatsink.
2.3 Installation of Memory Modules (DIMM)
P4V88 motherboard provides four 184-pin DDR (Double Data Rate) DIMM slots, and supports Dual Channel Memory Technology. For dual channel configuration, you always need to install identical (the same brand, speed, size and chiptype) DDR DIMM pair in the slots of the same color. In other words, you have to install identical DDR DIMM pair in Dual Channel A (DDR1 and DDR3; Blue slots; see p.8 No.6) or identical DDR DIMM pair in Dual Channel B (DDR2 and DDR4; Black slots; see p.8 No.10), so that Dual Channel Memory Technology can be activated. This motherboard also allows you to install four DDR DIMMs for dual channel configuration, and please install identical DDR DIMMs in all four slots. You may refer to the Dual Channel Memory Configuration Table below. Dual Channel Memory Configurations DDR1 (Blue Slot) Populated Populated DDR2 (Black Slot) Populated Populated DDR3 (Blue Slot) Populated Populated DDR4 (Black Slot) Populated Populated

Step 2. Step 3. Step 4. Step 5. Step 6.

2.5 Jumpers Setup

The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is Short. If no jumper cap is placed on pins, the jumper is Open. The illustration shows a 3-pin jumper whose pin1 and pin2 are Short when jumper cap is placed on these 2 pins. Jumper PS2_USB_PWR1

(see p.8, No. 1)

Setting

1_2 +5V 2_3 +5VSB

Short pin2, pin3 to enable
+5VSB (standby) for PS/2 or USB wake up events. Note: To select +5VSB, it requires 2 Amp and higher standby current provided by power supply. JR1(see p.8, No. 26) JL1(see p.8, No. 25)
Note: If the jumpers JL1 and JR1 are short, both the front panel and the rear panel audio connectors can work. Clear CMOS
(CLRCMOS1, 2-pin jumper) (see p.8, No. 15)

2-pin jumper

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes system setup information such as system password, date, time, and system setup parameters. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord, then use a jumper cap to short the pins on CLRCMOS1 for 3 seconds. Please rem ember to remove the jumper cap after clearing the CMOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action.
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

FDD Connector

(33-pin FLOPPY1) (see p.8, No. 16)

Pin1 FLOPPY1

the red-striped side to Pin1
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE Connector (Blue)
(39-pin IDE1, see p.8, No. 9)
Secondary IDE Connector (Black)
(39-pin IDE2, see p.8, No. 8)
connect the blue end to the motherboard
connect the black end to the IDE devices
80-conductor ATA 66/100/133 cable
Note: If you use only one IDE device on this motherboard, please set the IDE device as Master. Please refer to the instruction of your IDE device vendor for the details. Besides, to optimize compatibility and performance, please connect your hard disk drive to the primary IDE connector (IDE1, blue) and CD-ROM to the secondary IDE connector (IDE2, black). Serial ATA Connectors
(SATA1: see p.8, No. 13) (SATA2: see p.8, No. 12)

SPEAKER DUMMY DUMMY +5V

Please connect the chassis speaker to this header.

Chassis Fan Connector

(3-pin CHA_FAN1) (see p.8, No. 19)

GND +12V CHA_FAN_SPEED

Please connect the chassis fan cable to this connector and match the black wire to the ground pin. Please connect the CPU fan cable to this connector and match the black wire to the ground pin. Connect a Game cable to this connector if the Game port bracket is installed.

CPU Fan Connector

(3-pin CPU_FAN1) (see p.8, No. 2)

CPU_FAN_SPEED +12V GND

Game Connector
(15-pin GAME1) (see p.8, No. 22)
+5V JBB1 JBX MIDI_OUT JBY JBB2 MIDI_IN
+5V JAB2 JAY GND GND JAX JAB1 +5V

ATX Power Connector

(20-pin ATXPWR1) (see p.8, No. 31)
Please connect an ATX power supply to this connector.

ATX 12V Connector

(4-pin ATX12V1) (see p.8, No. 7)
Please note that it is necessary to connect a power supply with ATX 12V plug to this connector so that it can provides sufficient power. Failing to do so will cause the failure to power up.
2.7 Serial ATA (SATA) Hard Disks Installation
This motherboard adopts VIA VT8237 southbridge chipset that supports Serial ATA (SATA) hard disks and RAID functions. You may install SATA hard disks on this motherboard for internal storage devices. This section will guide you to install the SATA hard disks. STEP 1: Install the SATA hard disks into the drive bays of your chassis. STEP 2: Connect the SATA power cable to the SATA hard disk. STEP 3: Connect one end of the SATA data cable to the motherboards SATA connector. STEP 4: Connect the other end of the SATA data cable to the SATA hard disk.
2.8 Hot Plug and Hot Swap Functions for SATA HDDs
P4V88 motherboard supports Hot Plug and Hot Swap functions for SATA Devices. NOTE What is Hot Plug Function?
If the SATA HDDs are NOT set for RAID configuration, it is called Hot Plug for the action to insert and remove the SATA HDDs while the system is still power-on and in working condition. However, please note that it cannot perform Hot Plug if the OS has been installed into the SATA HDD.
What is Hot Swap Function?
If SATA HDDs are built as RAID1 then it is called Hot Swap for the action to insert and remove the SATA HDDs while the system is still power-on and in working condition.
2.9 Making An SATA Driver Diskette
If you want to install Windows 2000 or Windows XP on your SATA HDDs, you will need to make an SATA driver diskette before you start the OS installation. STEP 1: Insert the ASRock Support CD into your optical drive to boot your system. (Do NOT insert any floppy diskette into the floppy drive at this moment!) STEP 2: During POST at the beginning of system boot-up, press <F11> key, and then a window for boot devices selection appears. Please select CDROM as the boot device. STEP 3: When you see the message on the screen, Do you want to generate Serial ATA driver diskette [YN]?, press <Y>. STEP 4: Then you will see these messages, Please insert a diskette into the floppy drive. WARNING! Formatting the floppy diskette will lose ALL data in it! Start to format and copy files [YN]? Please insert a floppy diskette into the floppy drive, and press <Y>. STEP 5: The system will start to format the floppy diskette and copy SATA drivers into the floppy diskette. Once you have the SATA driver diskette ready, you may start to install Windows 2000 / Windows XP on your system directly without setting the RAID configuration on your system, or you may start to use VT8237 SATA RAID BIOS to set RAID 0 / RAID 1 / JBOD configuration before you install the OS. Before you start to configure the RAID function, you need to check the installation guide in the Support CD for proper configuration. Please refer to the document in the Support CD, Guide to SATA Hard Disks Installation and RAID Configuration, which is located in the folder at the following path:. \ SATA RAID BIOS You may also set the RAID configuration by using VIA RAID Tool in Windows environment. Please refer to the document in the Support CD, Guide to VIA RAID Tool, which is located in the folder at the following path:. \ VIA RAID Tool

3. BIOS SETUP UTILITY

3.1 Introduction
This section explains how to use the BIOS SETUP UTILITY to configure your system. The Flash Memory on the motherboard stores the BIOS SETUP UTILITY. You may run the BIOS SETUP UTILITY when you start up the computer. Please press <F2> during the Power-On-Self-Test (POST) to enter the BIOS SETUP UTILITY, otherwise, POST will continue with its test routines. If you wish to enter the BIOS SETUP UTILITY after POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. You may also restart by turning the system off and then back on.
Because the BIOS software is constantly being updated, the following BIOS setup screens and descriptions are for reference purpose only, and they may not exactly match what you see on your screen.

3.1.1 BIOS Menu Bar

screen has a menu bar with the following selections: To set up the system time/date information To set up the advanced BIOS features To display current hardware status To set up the default system device to locate and load the Operating System Security To set up the security features Exit To exit the current screen or the BIOS SETUP UTILITY Use < > key or < > key to choose among the selections on the menu bar, and then press <Enter> to get into the sub screen. The top of the Main Advanced H/W Monitor Boot

3.1.2 Navigation Keys

Please check the following table for the function description of each navigation key. Navigation Key(s) / / + / <Enter> <F1> <F9> <F10> <ESC> Function Description Moves cursor left or right to select Screens Moves cursor up or down to select items To change option for the selected items To bring up the selected screen To display the General Help Screen To load optimal default values for all the settings To save changes and exit the BIOS SETUP UTILITY To jump to the Exit Screen or exit the current screen

3.2 Main Screen

When you enter the BIOS SETUP UTILITY, the Main screen will appear and display the system overview
BIOS SETUP UTILITY H/W Monitor Boot

Advanced

Security

System Overview

System Time System Date BIOS Version Processor Type Processor Speed Cache Size Microcode Update Total Memory DIMM DIMM DIMM DIMM : : : : : [17:00:09] [Tue 02/24/2004] P4V88 BIOS P1.00 Intel (R) Pentium (R) 4 CPU 2.40 GHz 2400 MHz 512KB 0F24/1E
Use [Enter], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system Time.
: 512MB Dual-Channel Memory Mode : 256MB/166MHz (DDR333) : None : 256MB/166MHz (DDR333) : None

3.3.2 Chipset Configuration
BIOS SETUP UTILITY Advanced Chipset Configuration
DRAM Frequency Flexibility Option DRAM CAS# Latency DRAM Command Rate DRAM Bus Selection DRAM Voltage AGP Voltage Primary Graphics Adapter AGP Aperture Size AGP Mode AGP Fast Write PCI Delay Transaction OnBoard LAN OnBoard AC'97 Audio [Auto] [Disabled] [Auto] [2T Command] [Auto] [Normal] [High] [PCI] [64MB] [Auto] [Disabled] [Disabled] [Eabled] [Auto] Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit Options 133MHz (DDR266) 166MHz (DDR333) 200MHz (DDR400) Auto

+F1 F9 F10 ESC

DRAM Frequency If [Auto] is selected, the motherboard will detect the memory module(s) inserted and assigns appropriate frequency automatically. You may also select other value as operating frequency: [133MHz (DDR 266)], [166MHz (DDR 333)], [200MHz (DDR 400)].
Flexibility Option The default value of this option is [Disabled]. It will allow better tolerance for memory compatibility when it is set to [Enabled]. DRAM CAS# Latency Use this item to adjust the means of memory accessing. Configuration options: [Auto], [2.5], [2], and [3]. DRAM Command Rate Use this to select among [2T Command] and [1T Command] for DRAM Command Rate. The default value is [2T Command]. DRAM Bus Selection The default value is [Auto], which will automatically select the proper access mode for the system. You may select between [Single Channel] and [Dual Channel] if you have properly set the dual channel memory configuration. DRAM Voltage Use this to select among [Normal] and [High] for DRAM Voltage. The default value is [Normal]. AGP Voltage Use this to select among [Normal] and [High] for AGP Voltage. The default value is [High]. Primary Graphics Adapter This allows you to select [PCI] or [AGP] as the primary graphics adapter. The default vaule is [PCI]. AGP Aperture Size It refers to a section of the PCI memory address range used for graphics memory. It is recommended to leave this field at the default value unless the installed AGP cards specifications requires other sizes. AGP Mode The default value of this feature is set to [Auto]. If you install an 8X-AGP card on this motherboard, you may select [Auto], [8X] or [4X] as the AGP mode. If the installed AGP card is a 4X-AGP card, then you may set the AGP mode as [Auto], [4X], [2X], or [1X]. AGP Fast Write This allows you to enable or disable the feature of AGP fast write protocol support. PCI Delay Transaction Enable PCI Delay Transaction feature will free the PCI Bus when the CPU is accessing 8-bit ISA cards. Disable this feature when using ISA cards that are not PCI 2.1 compliant.

OnBoard LAN This allows you to enable or disable the onboard LAN feature. OnBoard AC97 Audio Select [Auto] or [Disabled] for the onboard AC97 Audio feature.

3.3.3 ACPI Configuration

BIOS SETUP UTILITY Advanced ACPI Configuration
Suspend To RAM Restore on AC / Power Loss Ring-In Power On PCI Devices Power On PS / 2 Keyboard Power On RTC Alarm Power On [Disabled] [Power Off] [Disabled] [Disabled] [Disabled] [Disabled] Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit Select auto-detect or disable the STR feature.
Restore on AC/Power Loss Use this item to set the power state after an unexpected AC/power loss. If [Power Off] is selected, the AC/power remains off when the power recovers. If [Power On] is selected, the AC/power resumes and the system starts to boot up when the power recovers. Ring-In Power On Use this item to enable or disable Ring-In signals to turn on the system from the power-soft-off mode. PCI Devices Power On Use this item to enable or disable PCI devices to turn on the system from the power-soft-off mode. PS/2 Keyboard Power On Use this item to enable or disable PS/2 keyboard to turn on the system from the power-soft-off mode. RTC Alarm Power On Use this item to enable or disable RTC (Real Time Clock) to power on the system.

3.3.4 IDE Configuration

BIOS SETUP UTILITY Advanced IDE Configuration
OnBoard IDE Controller Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave [Both] [Hard Disk] [Not Detected] [Not Detected] [Not Detected] DISABLED: disables the integrated IDE Controller. PRIMARY: enables only the Primary IDE Controller. SECONDARY: enables only the Secondary IDE Controller. BOTH: enables both IDE Controllers. Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit
OnBoard IDE Controller You may enable either the primary IDE channel or the secondary IDE channel. Or you may enable both the primary and the secondary IDE channels by selecting [Both]. Set to [Disabled] will disable the both. Configuration options: [Disabled], [Primary], [Secondary], [Both]. IDE Device Configuration You may set the IDE configuration for the device that you specify. We will use the Primary IDE Master as the example in the following instruction, which can be applied to the configurations of Primary IDE Slave, Secondary IDE Master, and Secondary IDE Slave as well.

BIOS SETUP UTILITY Advanced Primary IDE Master
Device Vendor Size LBA Mode Block Mode PIO Mode Async DMA Ultra DMA S.M.A.R.T. Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T. 32Bit Data Transfer :Hard Disk :ST340014A :40.0 GB :Supported :16Sectors :4 :MultiWord DMA-2 :Ultra DMA-5 :Supported [Auto] [Auto] [Auto] [Auto] [Auto] [Disabled] [Disabled]
Select the type of device connected to the system.
Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit
TYPE Use this item to configure the type of the IDE device that you specify. Configuration options: [Not Installed], [Auto], [CD/DVD], and [ARMD]. [Not Installed]: Select [Not Installed] to disable the use of IDE device. [Auto]: Select [Auto] to automatically detect the hard disk drive. After selecting the hard disk information into BIOS, use a disk utility, such as FDISK, to partition and format the new IDE hard disk drives. This is necessary so that you can write or read data from the hard disk. Make sure to set the partition of the Primary IDE hard disk drives to active. [CD/DVD]: This is used for IDE CD/DVD drives. [ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device), such as MO. LBA/Large Mode Use this item to select the LBA/Large mode for a hard disk > 512 MB under DOS and Windows; for Netware and UNIX user, select [Disabled] to disable the LBA/Large mode. Block (Multi-Sector Transfer) The default value of this item is [Auto]. If this feature is enabled, it will enhance hard disk performance by reading or writing more data during each transfer. PIO Mode Use this item to set the PIO mode to enhance hard disk performance by optimizing the hard disk timing. DMA Mode DMA capability allows the improved transfer-speed and data-integrity for compatible IDE devices. S.M.A.R.T. Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) feature. Configuration options: [Disabled], [Auto], [Enabled]. 32-Bit Data Transfer Use this item to enable 32-bit access to maximize the IDE hard disk data transfer rate.
3.3.5 PCIPnP Configuration
BIOS SETUP UTILITY Advanced PCI / PnP Configuration

PCI Latency Timer PCI IDE BusMaster [32] [Enabled] Value in units of PCI clocks for PCI device latency timer register.
PCI Latency Timer The default value is 32. It is recommended to keep the default value unless the installed PCI expansion cards specifications require other settings. PCI IDE BusMaster Use this item to enable or disable the PCI IDE BusMaster feature.
3.3.6 Floppy Configuration
In this section, you may configure the type of your floppy drive.
BIOS SETUP UTILITY Advanced Floppy Configuration
Floppy A Floppy B [1.44 MB 31 2"] [Disabled] Select the type of floppy drive connected to the system.
3.3.7 Super IO Configuration
BIOS SETUP UTILITY Advanced Configure Super IO Chipset
OnBoard Floppy Controller Serial Port Address Infrared Port Address Parallel Port Address Parallel Port Mode EPP Version ECP Mode DMA Channel Parallel Port IRQ OnBoard Game Port OnBoard MIDI Port [Enabled] [3F8 / IRQ4] [Disabled] [378] [ECP + EPP] [1.9] [DMA3] [IRQ7] [Enabled] [Disabled] Allow BIOS to Enable or Disable Floppy Controller.
OnBoard Floppy Controller Use this item to enable or disable floppy drive controller. Serial Port Address Use this item to set the address for the onboard serial port or disable it. Configuration options: [Disabled], [3F8 / IRQ4], [2F8 / IRQ3], [3E8 / IRQ4], [2E8 / IRQ3]. Infrared Port Address Use this item to set the address for the onboard infrared port or disable it. Configuration options: [Disabled], [2F8 / IRQ3], and [2E8 / IRQ3]. Parallel Port Address Use this item to set the address for the onboard parallel port or disable it. Configuration options: [Disabled], [378], and [278]. Parallel Port Mode Use this item to set the operation mode of the parallel port. The default value is [ECP+EPP]. If this option is set to [ECP+EPP], it will show the EPP version in the following item, EPP Version. Configuration options: [Normal], [Bi-Directional], and [ECP+EPP]. EPP Version Use this item to set the EPP version. Configuration options: [1.9] and [1.7]. ECP Mode DMA Channel Use this item to set the ECP mode DMA channel. Configuration options: [DMA0], [DMA1], and [DMA3]. Parallel Port IRQ Use this item to set the IRQ for the parallel port. Configuration options: [IRQ5] and [IRQ7].
OnBoard Game Port Use this item to enable the Game Port or disable it. OnBoard MIDI Port Use this itme to select the address for the MIDI Port or disable it. Configuration options: [Disabled], [300], and [330].

3.3.8 USB Configuration

BIOS SETUP UTILITY Advanced USB Configuration
USB Devices Enabled : None USB Controller USB 2.0 Support Legacy USB Support [Enabled] [Enabled] [Disabled] Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit To enable or disable the onboard USB controllers.

USB Controller Use this item to enable or disable the use of USB controller. USB 2.0 Support Use this item to enable or disable the USB 2.0 support. Legacy USB Support Use this item to enable or disable the support to emulate legacy I/O devices such as mouse, keyboard,. etc. Or you may select [Auto] so that the system will start to auto-detect; if there is no USB device connected, Auto option will disable the legacy USB support.
3.4 Hardware Health Event Monitoring Screen
In this section, it allows you to monitor the status of the hardware on your system, including the parameters of the CPU temperature, motherboard temperature, CPU fan speed, chassis fan speed, and the critical voltage.
BIOS SETUP UTILITY Boot H/W Monitor
Hardware Health Event Monitoring
CPU Temperature M / B Temperature CPU Fan Speed Chassis Fan Speed Vcore + 3.30V + 5.00V + 12.00V : 37 C / 98 F : 31 C / 87 F : 2463 RPM : N/A : : : : 1.629V 3.306V 5.067V 11.890V F1 F9 F10 ESC
Select Screen Select Item General Help Load Defaults Save and Exit Exit

3.5 Boot Screen

In this section, it will display the available devices on your system for you to configure the boot settings and the boot priority.

Boot Settings

Boot Settings Configuration Boot Device Priority Removable Drives
Configure Settings during System Boot.
3.5.1 Boot Settings Configuration
BIOS SETUP UTILITY Boot Boot Settings Configuration
Boot From Network Bootup Num-Lock [Disabled] [On] To enable or disable the boot from network feature.
Boot From Network Use this item to enable or disable the Boot From Network feature. Boot Up Num-Lock If this item is set to [On], it will automatically activate the Numeric Lock function after boot-up.
3.5.2 Boot Device Priority
In this section, you may specify the boot sequence from the available devices in your system.
BIOS SETUP UTILITY Boot Boot Device Priority
1st Boot Device 2nd Boot Device 3rd Boot Device [1st FLOPPY DRIVE] [HDD: PM-MAXTOR 6L08] [CD / DVD] Specifies the boot sequence from the available devices. A device enclosed in parenthesis has been disabled in the corresponding type menu. Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit

Likewise, you may also specify the boot sequence from the available devices for the hard disk drives, the removable drives, and the CD/DVD drives.

3.6 Security Screen

In this section, you may set or change the supervisor/user password for the system. For the user password, you may also clear it.

Security Settings

Supervisor Password User Password : Not Installed : Not Installed
Install or Change the password.
Change Supervisor Password Change User Password Clear User Password
Select Screen Select Item Change General Help Load Defaults Save and Exit Exit

3.7 Exit Screen

Main Advanced BIOS SETUP UTILITY H/W Monitro Boot Security
Exit system setup after saving the changes. F10 key can be used for this operation.

Exit Options

Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults
Save Changes and Exit When you select this option, it will pop-out the following message, Save configuration changes and exit setup? Select [OK] to save the changes and exit the BIOS SETUP UTILITY. Discard Changes and Exit When you select this option, it will pop-out the following message, Discard changes and exit setup? Select [OK] to exit the BIOS SETUP UTILITY without saving any changes. Discard Changes When you select this option, it will pop-out the following message, Discard changes? Select [OK] to discard all changes. Load Optimal Defaults When you select this option, it will pop-out the following message, Load optimal defaults? Select [OK] to load the default values for all the setup configurations.

4. Software Support

4.1 Install Operating System
This motherboard supports various Microsoft Windows operating systems: 98 SE / ME / 2000 / XP. Because motherboard settings and hardware options vary, use the setup procedures in this chapter for general reference only. Refer to your OS documentation for more information.
4.2 Support CD Information
The Support CD that came with the motherboard contains necessary drivers and useful utilities that enhance the motherboard features.
4.2.1 Running The Support CD
To begin using the support CD, insert the CD into your CD-ROM drive. The CD automatically displays the Main Menu if AUTORUN is enabled in your computer. If the Main Menu did not appear automatically, locate and double click on the file ASSETUP.EXE from the BIN folder in the Support CD to display the menus.

4.2.2 Drivers Menu

The Drivers Menu shows the available devices drivers if the system detects installed devices. Please install the necessary drivers to activate the devices.

4.2.3 Utilities Menu

The Utilities Menu shows the applications software that the motherboard supports. Click on a specific item then follow the installation wizard to install it.

P4V88-M+

User Manual
Version 1.0 Published May 2005 Copyright2005 ASRock INC. All rights reserved.

Copyright Notice:

No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners benefit, without intent to infringe.

Disclaimer:

Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. With respect to the contents of this manual, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the manual or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ASRock Website: http://www.asrock.com

Contents

1. Introduction.. 5
1.1 1.2 1.3 1.4 Package Contents... Specifications... Motherboard Layout.. ASRock I/O PlusTM.... 34 35

2. Installation.. 10

Pre-installation Precautions... 2.1 CPU Installation.. 2.2 Installation of CPU Fan and Heatsink.. 2.3 Installation of Memory Modules (DIMM).. 2.4 Expansion Slots (PCI and AGP Slots).. 2.5 Jumpers Setup.. 2.6 Onboard Headers and Connectors.. 2.7 Serial ATA (SATA) Hard Disks Installation. 2.8 Hot Plug and Hot Swap Functions for SATA HDDs. 2.9 Installing Windows 2000 / Windows XP With RAID Functions... 2.10 Installing Windows 98 / ME / 2000 / XP Without RAID Functions... 3.1 Introduction... 3.1.1 BIOS Menu Bar.. 3.1.2 Navigation Keys... 3.2 Main Screen.. 3.3 Advanced Screen.. 3.3.1 CPU Configuration.. 3.3.2 Chipset Configuration.. 3.3.3 ACPI Configuration.. 3.3.4 IDE Configuration.. 3.3.5 PCIPnP Configuration.. 3.3.6 Floppy Configuration.. 3.3.7 Super IO Configuration.. 3.3.8 USB Configuration.. 3.4 Hardware Health Event Monitoring Screen. 3.5 Boot Screen.. 3.5.1 Boot Settings Configuration.. 3.5.2 Boot Device Priority.. 3.6 Security Screen.. 3.7 Exit Screen...
SETUP 3. BIOS S ETUP UTILITY... 21

4. Software Support.. 36

4.1 Install Operating System.. 4.2 Support CD Information.. 4.2.1 Running Support CD.. 4.2.2 Drivers Menu... 4.2.3 Utilities Menu... 4.2.4 Contact Information... 36 36

1. Introduction

Thank you for purchasing ASRock P4V88-M+ motherboard, a reliable motherboard produced under ASRocks consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRocks commitment to quality and endurance. In this manual, chapter 1 and 2 contain introduction of the motherboard and step-bystep guide to the hardware installation. Chapter 3 and 4 contain the configuration guide to BIOS setup and information of the Support CD.
Because the motherboard specifications and the BIOS software might be updated, the content of this manual will be subject to change without notice. In case any modifications of this manual occur, the updated version will be available on ASRock website without further notice. You may find the latest memory and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com

CAUTION!

1. 2. About the setting of Hyper Threading Technology, please check page 24. This motherboard supports Dual Channel Memory Technology. Before you implement Dual Channel Memory Technology, make sure to read the installation guide of memory modules on page 12 for proper installation. 3. While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal 4. 5. grease between the CPU and the heatsink when you install the PC system. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard! It may cause permanent damage! Power Management for USB 2.0 works fine under Microsoft Windows XP SP1 / 2000 SP4. It may not work properly under Microsoft Windows 98 / ME. 6. Although this motherboard offers stepless control, it is not recommended to perform over-clocking. Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU.

1.3 Motherboard Layout

21.6cm (8.5 in)

1 PS2_USB_PWR1

CPU_FAN1

PS2 Mouse

ATX12V1

PARALLEL PORT

Ps2 Keyboard

PGA478

DDR400

USB 2.0 T: USB2 B: USB3

USB 2.0 T: USB0 Top: B: USB1 RJ-45

USB 2.0 T: USB4 B: USB5

P V Ch T8 IA ip 80 se t

USB4_5

24.4cm (9.6in)

FSB800

Prescott 800 Dual Channel P4V88-M+
DDR1 (64/72 bit, 184-pin module)
DDR3 (64/72 bit, 184-pin module)

ATXPWR1

IDE1 IDE2

Super I/O

PCI 1 5.1CH

Audio CODEC

VIA VT8237R
Top: Line In Center: Line Out Bottom: Mic In

AGP 8X

CMOS Battery

1.5V_AGP1

2Mb BIOS

CLRCMOS1

ATA133

USB2.0

SPEAKER1

PLED PWRBTN

AUDIO1

FLOPPY1

CHA_FAN1

1 HDLED RESET

PANEL 1
PS2_USB_PWR1 Jumper CPU Fan Connector (CPU_FAN1) CPU Heatsink Retention Module 2 x 184-pin DDR DIMM Slots (Dual Channel: DDR1, DDR3; Blue) ATX 12V Connector (ATX12V1) ATX Power Connector (ATXPWR1) Secondary IDE Connector (IDE2, Black) Primary IDE Connector (IDE1, Blue) Clear CMOS Jumper (CLRCMOS1) Secondary Serial ATA Connector (SATA2) Primary Serial ATA Connector (SATA1) System Panel Header (PANEL1) USB 2.0 Header (USB67, Blue) South Bridge Controller

AGP Slot (1.5V_AGP1) Chassis Speaker Header (SPEAKER 1) Chassis Fan Connector (CHA_FAN1) Floppy Connector (FLOPPY1) Infrared Module Header (IR1) Front Panel Audio Header (AUDIO1) JR1 / JL1 Jumpers 2 x PCI Slots (PCI1- 2) Flash Memory Internal Audio Connector: CD1 (Black) Internal Audio Connector: AUX1 (White) North Bridge Controller Shared USB 2.0 Header (USB4_5, Blue) CPU Socket

1.4 ASRock I/O Plus TM

Parallel Port RJ-45 Port Line In (Light Blue) Line Out (Lime) Microphone (Pink) 2 x Shared USB 2.0 Ports (USB4, USB5)
2 x USB 2.0 Ports (USB0, USB1) 2 x USB 2.0 Ports (USB2, USB3) Serial Port: COM1 PS/2 Keyboard Port (Purple) PS/2 Mouse Port (Green)

2. Installation

P4V88-M+ is a Micro ATX form factor (9.6-in x 8.5-in, 24.4 cm x 21.6 cm) motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component. 2. To avoid damaging the motherboard components due to static electricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components. 3. Hold components by the edges and do not touch the ICs. 4. Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component.
Before you install or remove any component, ensure that the power is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.

2.1 CPU Installation

Step 1. Step 2. Step 3. Unlock the socket by lifting the lever up to a 90 angle. Position the CPU directly above the socket such that its marked corner matches the base of the socket lever. Carefully insert the CPU into the socket until it fits in place.
The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to avoid bending of the pins.

Step 4.

When the CPU is in place, press it firmly on the socket while you push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked.
CPU Marked Corner Lift Lever Up to 90 Socket Marked Corner
STEP 1: Lift The Socket Lever Up to 90
STEP 2/STEP 3: Match The CPU Marked Corner to The Socket Marked Corner
STEP 4: Push Down And Lock The Socket Lever
2.2 Installation of CPU Fan and Heatsink

This motherboard adopts 478-pin CPU socket to support Intel Pentium 4 / Celeron CPU. It requires larger heatsink and cooling fan to dissipate heat. You also need to spray thermal grease between the CPU and the heatsink to improve heat dissipation. Make sure that the CPU and the heatsink are securely fastened and in good contact with each other. Then connect the CPU fan to the CPU_FAN connector (CPU_FAN1, see p.8 No. 2). For proper installation, please kindly refer to the instruction manuals of the CPU fan and the heatsink.
2.3 Installation of Memory Modules (DIMM)
P4V88-M+ motherboard provides two 184-pin DDR (Double Data Rate) DIMM slots, and supports Dual Channel Memory Technology. For dual channel configuration, you always need to install two identical (the same brand, speed, size and chip-type) memory modules in the DDR DIMM slots to activate Dual Channel Memory Technology. Otherwise, it will operate at single channel mode.
If you install only one memory module or two non-identical memory modules, it is unable to activate the Dual Channel Memory Technology.

Installing a DIMM

Please make sure to disconnect power supply before adding or removing DIMMs or the system components.

Step 1. Step 2.

Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.

notch break

The DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

Step 3.

Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated.
2.4 Expansion Slots (PCI and AGP Slots)
There are 2 PCI slots and 1 AGP slot on P4V88-M+ motherboard. PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI interface. AGP slot: The AGP slot is used to install a graphics card. The ASRock AGP slot has a special design of clasp that can securely fasten the inserted graphics card.
Please do NOT use a 3.3V AGP card on the AGP slot of this motherboard! It may cause permanent damage! For the voltage information of your AGP card, please check with the AGP card vendors.
Installing an expansion card
Step 1. Before installing the expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation. Remove the system unit cover (if your motherboard is already installed in a chassis). Remove the bracket facing the slot that you intend to use. Keep the screws for later use. Align the card connector with the slot and press firmly until the card is completely seated on the slot. Fasten the card to the chassis with screws. Replace the system cover.

Step 2. Step 3. Step 4. Step 5. Step 6.

2.5 Jumpers Setup

The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is Short. If no jumper cap is placed on pins, the jumper is Open. The illustration shows a 3-pin jumper whose pin1 and pin2 are Short when jumper cap is placed on these 2 pins. Jumper PS2_USB_PWR1

(see p.8, No. 1)

Setting

1_2 2_3

Short pin2, pin3 to enable +5VSB (standby) for PS/2 +5VSB +5V or USB wake up events. Note: To select +5VSB, it requires 2 Amp and higher standby current provided by power supply. JR1(see p.8, No. 21) JL1(see p.8, No. 21)
Note: If the jumpers JL1 and JR1 are short, both the front panel and the rear panel audio connectors can work. Clear CMOS
(CLRCMOS1, 2-pin jumper) (see p.8, No. 9)

2-pin jumper

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes system setup information such as system password, date, time, and system setup parameters. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short 2 pins on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action.
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!

FDD Connector

(33-pin FLOPPY1) (see p.8, No. 18)

Pin1 FLOPPY1

the red-striped side to Pin1
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE Connector (Blue)
(39-pin IDE1, see p.8, No. 8)
Secondary IDE Connector (Black)
(39-pin IDE2, see p.8, No. 7)
connect the blue end to the motherboard
connect the black end to the IDE devices
80-conductor ATA 66/100/133 cable
Note: If you use only one IDE device on this motherboard, please set the IDE device as Master. Please refer to the instruction of your IDE device vendor for the details. Besides, to optimize compatibility and performance, please connect your hard disk drive to the primary IDE connector (IDE1, blue) and CD-ROM to the secondary IDE connector (IDE2, black). Serial ATA Connectors
(SATA1: see p.8, No. 11) (SATA2: see p.8, No. 10)
These two Serial ATA (SATA) connectors support SATA data cables for internal storage devices. The current SATA interface allows up to 1.5 Gb/s data transfer rate. Either end of the SATA data cable can be connected to the SATA hard disk or the SATA connector on the motherboard.

1. Windows 98 / Windows ME does not support RAID functions. 2. If you want to use VIA RAID Tool in Windows environment, please install SATA drivers from the Support CD again so that VIA RAID Tool will be installed to your system as well.
2.10 Installing Windows 98 / ME / 2000 / XP Without RAID Functions
If you want to install Windows 98 / ME / 2000 / XP on your SATA HDDs without RAID functions or you want to install Windows 98 / ME / 2000 / XP on your IDE HDDs instead of SATA HDDs, please follow the below steps.
If you want to install Windows 98 / Windows ME on your SATA HDDs without RAID functions, you dont have to set up BIOS. Please install Windows 98 / Windows ME OS on your system directly.
STEP 1: Set Up BIOS. (For Windows 2000 / XP) A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration. B. Set the SATA Operation Mode option from [RAID] to [non-RAID]. STEP 2: Install Windows 98 / ME / 2000 / XP OS on your system. After setting up BIOS, you can start to install Windows 98 / ME / 2000 / XP on your system.
If you dont want to set up RAID functions, there is no need to make a SATA driver diskette.

3. BIOS SETUP UTILITY

3.1 Introduction
This section explains how to use the BIOS SETUP UTILITY to configure your system. The Flash Memory on the motherboard stores the BIOS SETUP UTILITY. You may run the BIOS SETUP UTILITY when you start up the computer. Please press <F2> during the Power-On-Self-Test (POST) to enter the BIOS SETUP UTILITY, otherwise, POST will continue with its test routines. If you wish to enter the BIOS SETUP UTILITY after POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. You may also restart by turning the system off and then back on.
Because the BIOS software is constantly being updated, the following BIOS setup screens and descriptions are for reference purpose only, and they may not exactly match what you see on your screen.

3.1.1 BIOS Menu Bar

The top of the Main Advanced H/W Monitor Boot screen has a menu bar with the following selections: To set up the system time/date information To set up the advanced BIOS features To display current hardware status To set up the default system device to locate and load the Operating System Security To set up the security features Exit To exit the current screen or the BIOS SETUP UTILITY Use < > key or < > key to choose among the selections on the menu bar, and then press <Enter> to get into the sub screen.

3.1.2 Navigation Keys

Please check the following table for the function description of each navigation key. Navigation Key(s) / / + / <Enter> <F1> <F9> <F10> <ESC> Function Description Moves cursor left or right to select Screens Moves cursor up or down to select items To change option for the selected items To bring up the selected screen To display the General Help Screen To load optimal default values for all the settings To save changes and exit the BIOS SETUP UTILITY To jump to the Exit Screen or exit the current screen

3.2 Main Screen

When you enter the BIOS SETUP UTILITY, the Main screen will appear and display the system overview
BIOS SETUP UTILITY H/W Monitor Boot

Advanced

Security

System Overview

System Time System Date BIOS Version Processor Type Processor Speed Cache Size Microcode Update Total Memory DIMM 1 DIMM 2 : : : : : [17:00:09] [Wed 04/27/2005] P4V88-M+ BIOS P1.00 Intel (R) Pentium (R) 4 CPU 2.40 GHz 2400 MHz 512KB 0F24/1E
Use [Enter], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system Time.
: 512MB with 8MB share memory Dual-Channel Memory Mode : 256MB/166MHz (DDR333) : 256MB/166MHz (DDR333)

+Tab F1 F9 F10 ESC

Select Screen Select Item Change Field Select Field General Help Load Defaults Save and Exit Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
System Time [Hour:Minute:Second] Use this item to specify the system time. System Date [Day Month/Date/Year] Use this item to specify the system date.

3.3 Advanced Screen

In this section, you may set the configurations for the following items: CPU Configuration, Chipset Configuration, ACPI Configuration, IDE Configuration, PCIPnP Configuration, Floppy Configuration, SuperIO Configuration, and USB Configuration.

Configure CPU

Advanced Settings
WARNING : Setting wrong values in below sections may cause system to malfunction. CPU Configuration Chipset Configuration ACPI Configuration IDE Configuration PCIPnP Configuration Floppy Configuration SuperIO Configuration USB Configuration

Enter F1 F9 F10 ESC

Select Screen Select Item Go to Sub Screen General Help Load Defaults Save and Exit Exit
Setting wrong values in this section may cause the system to malfunction.

3.3.1 CPU Configuration

BIOS SETUP UTILITY Advanced CPU Configuration
CPU Host Frequency Actual Frequency (MHz) Spread Spectrum Ratio Status Ratio Actual Value CPU Thermal Throttling Hyper Threading Technology [Auto] [133] [Disabled] : Locked : 18 [Enabled] [Auto] +F1 F9 F10 ESC Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit Select how to set the CPU host frequency.

CPU Host Frequency While entering setup, BIOS auto detects the present CPU host frequency of this motherboard. The actual CPU host frequency will show in the following item. Spread Spectrum This item should always be [Disabled] for better system stability.
Ratio Status This is a read-only item, which displays whether the ratio status of this motherboard is Locked or Unlocked. If it shows Unlocked, you will find an item Ratio CMOS Setting appears to allow you changing the ratio value of this motherboard. If it shows Locked, then the item Ratio CMOS Setting will be hidden. If you use the ratio value to time the CPU frequency, it will be equal to the core speed of the installed processor. Ratio Actual Value This is a read-only item, which displays the ratio actual value of this motherboard. CPU Thermal Throttling You may select [Enabled] to enable P4 CPU internal thermal control mechanism to keep the CPU from overheated. Hyper Threading Technology To enable this feature, it requires a computer system with an Intel Pentium4 processor that supports Hyper-Threading technology and an operating system that includes optimization for this technology, such as Microsoft Windows XP. Set to [Auto] if using Microsoft Windows XP, or Linux kernel version 2.4.18 or higher. This option will be hidden if the installed CPU does not support Hyper-Threading technology.
3.3.2 Chipset Configuration
BIOS SETUP UTILITY Advanced Chipset Configuration
DRAM Frequency Flexibility Option DRAM CAS# Latency DRAM Command Rate DRAM Bus Selection DRAM Voltage AGP Voltage Primary Graphics Adapter AGP Aperture Size AGP Mode AGP Fast Write PCI Delay Transaction OnBoard LAN OnBoard AC'97 Audio [Auto] [Disabled] [Auto] [2T Command] [Auto] [Normal] [High] [PCI] [64MB] [Auto] [Disabled] [Disabled] [Eabled] [Auto] Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit Options 133MHz (DDR266) 166MHz (DDR333) 200MHz (DDR400) Auto

+F1 F9 F10 ESC

DRAM Frequency If [Auto] is selected, the motherboard will detect the memory module(s) inserted and assigns appropriate frequency automatically. You may also select other value as operating frequency: [133MHz (DDR 266)], [166MHz (DDR 333)], [200MHz (DDR 400)].

Flexibility Option The default value of this option is [Disabled]. It will allow better tolerance for memory compatibility when it is set to [Enabled]. DRAM CAS# Latency Use this item to adjust the means of memory accessing. Configuration options: [Auto], [2.5], [2], and [3]. DRAM Command Rate Use this to select among [2T Command] and [1T Command] for DRAM Command Rate. The default value is [2T Command]. DRAM Bus Selection The default value is [Auto], which will automatically select the proper access mode for the system. You may select between [Single Channel] and [Dual Channel] if you have properly set the dual channel memory configuration. DRAM Voltage Use this to select among [Normal] and [High] for DRAM Voltage. The default value is [Normal]. AGP Voltage Use this to select among [Normal] and [High] for AGP Voltage. The default value is [High]. Primary Graphics Adapter This allows you to select [PCI] or [AGP] as the primary graphics adapter. The default vaule is [PCI]. AGP Aperture Size It refers to a section of the PCI memory address range used for graphics memory. It is recommended to leave this field at the default value unless the installed AGP cards specifications requires other sizes. AGP Mode The default value of this feature is set to [Auto]. If you install an 8X-AGP card on this motherboard, you may select [Auto], [8X] or [4X] as the AGP mode. If the installed AGP card is a 4X-AGP card, then you may set the AGP mode as [Auto], [4X], [2X], or [1X]. AGP Fast Write This allows you to enable or disable the feature of AGP fast write protocol support. PCI Delay Transaction Enable PCI Delay Transaction feature will free the PCI Bus when the CPU is accessing 8-bit ISA cards. Disable this feature when using ISA cards that are not PCI 2.1 compliant.
OnBoard LAN This allows you to enable or disable the onboard LAN feature. OnBoard AC97 Audio Select [Auto] or [Disabled] for the onboard AC97 Audio feature.

3.3.3 ACPI Configuration

BIOS SETUP UTILITY Advanced ACPI Configuration
Suspend To RAM Restore on AC / Power Loss Ring-In Power On PCI Devices Power On PS / 2 Keyboard Power On RTC Alarm Power On [Disabled] [Power Off] [Disabled] [Disabled] [Disabled] [Disabled] Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit Select auto-detect or disable the STR feature.

Restore on AC/Power Loss Use this item to set the power state after an unexpected AC/power loss. If [Power Off] is selected, the AC/power remains off when the power recovers. If [Power On] is selected, the AC/power resumes and the system starts to boot up when the power recovers. Ring-In Power On Use this item to enable or disable Ring-In signals to turn on the system from the power-soft-off mode. PCI Devices Power On Use this item to enable or disable PCI devices to turn on the system from the power-soft-off mode. PS/2 Keyboard Power On Use this item to enable or disable PS/2 keyboard to turn on the system from the power-soft-off mode. RTC Alarm Power On Use this item to enable or disable RTC (Real Time Clock) to power on the system.

3.3.4 IDE Configuration

BIOS SETUP UTILITY Advanced IDE Configuration
OnBoard IDE Controller SATA Operation Mode Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave [Both] [RAID] [Hard Disk] [Not Detected] [Not Detected] [Not Detected] DISABLED: disables the integrated IDE Controller. PRIMARY: enables only the Primary IDE Controller. SECONDARY: enables only the Secondary IDE Controller. BOTH: enables both IDE Controllers. Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit
OnBoard IDE Controller You may enable either the primary IDE channel or the secondary IDE channel. Or you may enable both the primary and the secondary IDE channels by selecting [Both]. Set to [Disabled] will disable the both. Configuration options: [Disabled], [Primary], [Secondary], [Both]. SATA Operation Mode Use this item to adjust SATA Operation Mode. The default value of this option is [RAID]. If you dont want to operate RAID function on SATA HDDs, please select [non-RAID]. IDE Device Configuration You may set the IDE configuration for the device that you specify. We will use the Primary IDE Master as the example in the following instruction, which can be applied to the configurations of Primary IDE Slave, Secondary IDE Master, and Secondary IDE Slave as well.

BIOS SETUP UTILITY Advanced Primary IDE Master
Device Vendor Size LBA Mode Block Mode PIO Mode Async DMA Ultra DMA S.M.A.R.T. Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T. 32Bit Data Transfer :Hard Disk :ST340014A :40.0 GB :Supported :16Sectors :4 :MultiWord DMA-2 :Ultra DMA-5 :Supported [Auto] [Auto] [Auto] [Auto] [Auto] [Disabled] [Disabled]
Select the type of device connected to the system.
Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit
TYPE Use this item to configure the type of the IDE device that you specify. Configuration options: [Not Installed], [Auto], [CD/DVD], and [ARMD]. [Not Installed]: Select [Not Installed] to disable the use of IDE device. [Auto]: Select [Auto] to automatically detect the hard disk drive. After selecting the hard disk information into BIOS, use a disk utility, such as FDISK, to partition and format the new IDE hard disk drives. This is necessary so that you can write or read data from the hard disk. Make sure to set the partition of the Primary IDE hard disk drives to active. [CD/DVD]: This is used for IDE CD/DVD drives. [ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device), such as MO. LBA/Large Mode Use this item to select the LBA/Large mode for a hard disk > 512 MB under DOS and Windows; for Netware and UNIX user, select [Disabled] to disable the LBA/Large mode. Block (Multi-Sector Transfer) The default value of this item is [Auto]. If this feature is enabled, it will enhance hard disk performance by reading or writing more data during each transfer. PIO Mode Use this item to set the PIO mode to enhance hard disk performance by optimizing the hard disk timing. DMA Mode DMA capability allows the improved transfer-speed and data-integrity for compatible IDE devices. S.M.A.R.T. Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) feature. Configuration options: [Disabled], [Auto], [Enabled]. 32-Bit Data Transfer Use this item to enable 32-bit access to maximize the IDE hard disk data transfer rate.
3.3.5 PCIPnP Configuration
BIOS SETUP UTILITY Advanced PCI / PnP Configuration
PCI Latency Timer PCI IDE BusMaster [32] [Enabled] Value in units of PCI clocks for PCI device latency timer register.
PCI Latency Timer The default value is 32. It is recommended to keep the default value unless the installed PCI expansion cards specifications require other settings. PCI IDE BusMaster Use this item to enable or disable the PCI IDE BusMaster feature.
3.3.6 Floppy Configuration
In this section, you may configure the type of your floppy drive.
BIOS SETUP UTILITY Advanced Floppy Configuration
Floppy A Floppy B [1.44 MB 31 2"] [Disabled] Select the type of floppy drive connected to the system.

3.3.7 Super IO Configuration
BIOS SETUP UTILITY Advanced Configure Super IO Chipset
OnBoard Floppy Controller Serial Port Address Infrared Port Address Parallel Port Address Parallel Port Mode EPP Version ECP Mode DMA Channel Parallel Port IRQ OnBoard Game Port OnBoard MIDI Port [Enabled] [3F8 / IRQ4] [Disabled] [378] [ECP + EPP] [1.9] [DMA3] [IRQ7] [Enabled] [Disabled] Allow BIOS to Enable or Disable Floppy Controller.
OnBoard Floppy Controller Use this item to enable or disable floppy drive controller. Serial Port Address Use this item to set the address for the onboard serial port or disable it. Configuration options: [Disabled], [3F8 / IRQ4], [2F8 / IRQ3], [3E8 / IRQ4], [2E8 / IRQ3]. Infrared Port Address Use this item to set the address for the onboard infrared port or disable it. Configuration options: [Disabled], [2F8 / IRQ3], and [2E8 / IRQ3]. Parallel Port Address Use this item to set the address for the onboard parallel port or disable it. Configuration options: [Disabled], [378], and [278]. Parallel Port Mode Use this item to set the operation mode of the parallel port. The default value is [ECP+EPP]. If this option is set to [ECP+EPP], it will show the EPP version in the following item, EPP Version. Configuration options: [Normal], [Bi-Directional], and [ECP+EPP]. EPP Version Use this item to set the EPP version. Configuration options: [1.9] and [1.7]. ECP Mode DMA Channel Use this item to set the ECP mode DMA channel. Configuration options: [DMA0], [DMA1], and [DMA3]. Parallel Port IRQ Use this item to set the IRQ for the parallel port. Configuration options: [IRQ5] and [IRQ7].

3.3.8 USB Configuration

BIOS SETUP UTILITY Advanced USB Configuration
USB Devices Enabled : None USB Controller USB 2.0 Support Legacy USB Support [Enabled] [Enabled] [Disabled] Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit To enable or disable the onboard USB controllers.
USB Controller Use this item to enable or disable the use of USB controller. USB 2.0 Support Use this item to enable or disable the USB 2.0 support. Legacy USB Support Use this item to enable or disable the support to emulate legacy I/O devices such as mouse, keyboard,. etc. Or you may select [Auto] so that the system will start to auto-detect; if there is no USB device connected, Auto option will disable the legacy USB support.
3.4 Hardware Health Event Monitoring Screen
In this section, it allows you to monitor the status of the hardware on your system, including the parameters of the CPU temperature, motherboard temperature, CPU fan speed, chassis fan speed, and the critical voltage.