Auto fan off

The system fans power off automatically when the system is in sleep mode. This feature reduces both power consumption and system noise.
Chassis intrusion detection
The motherboard supports chassis intrusion monitoring through the ASUS ASIC. A chassis intrusion event is retained in the system memory for more protection.

Motherboard overview

Before you install the P4B533-VM motherboard, familiarize yourself with its physical configuration and available features to facilitate the motherboard installation and future upgrades. A sufficient knowledge of the motherboard specifications will also help you avoid mistakes that may damage the board and its components.

1.4.1 Major components

The following are the major components of the P4B533-VM motherboard as pointed out in the picture on page 1-5.
1. 2. 3. 4. 5. 6. 7. 8. 9. 11. DIP switches ATX 12V connector CPU socket North Bridge controller DDR DIMM sockets ATX power connector Super I/O controller Floppy connector IDE connectors South Bridge controller 19. PS/2 mouse port 20. Parallel port 21. RJ-45 port (optional) 22. Line In jack (optional) 23. Line Out jack (optional) 24. Microphone jack (optional) 25. USB 2.0 ports 1 and 2 26. Video port 27. Serial port 28. USB 2.0 ports 3 and 4 29. Keyboard port
10. Flash EEPROM 12. ASUS ASIC 13. AGP slot 14. Standby power LED 15. Audio CODEC (optional) 16. PCI slots 17. AGP warning LED 18. LAN PHY (optional)
See page 1-6 for the specifications of each component. Refer to Chapter 2 for detailed information on the components.
1.4.2 Core specifications
3 DIP switches. This 5-switch Dual Inline Package (DIP) allows you to set the CPU external frequency. ATX 12V connector. This power connector is for the 4-pin 12V plug from an ATX 12V power supply. CPU socket. A 478-pin surface mount, Zero Insertion Force (ZIF) socket for the Intel Pentium 4 Processor, with 533/400 MHz system bus that allows 4.3GB/s and 3.2GB/s data transfer rates. North bridge controller. The Intel 845G Graphics Memory Controller Hub (GMCH) provides the processor interface with 533/400 MHz frequency, system memory interface at 133/100MHz operation, and 1.5V AGP interface that supports AGP 2.0 specification including 4X/2X Fast Write protocol. The integrated graphics accelerator delivers 3D/2D video capabilities and a high bandwidth access to graphics data in the system memory at a 2.2GB/s or 1.6GB/s. The GMCH interconnects to the south bridge ICH4 via the Intel proprietary Hub Interface. DDR DIMM sockets. These two 184-pin DIMM sockets support up to 2GB using unbuffered non-ECC PC2100/1600 DDR DIMMs. ATX power connector. This 20-pin connector connects to an ATX +12V power supply. The power supply must have at least 1A on the +5V standby lead (+5VSB). Super I/O controller. This Low Pin Count (LPC) interface provides the commonly used Super I/O functionality. The chipset supports a high-performance floppy disk controller for a 360K/720K/1.44M/ 2.88M floppy disk drive, a multi-mode parallel port, two standard compatible UARTs, a Standard Infrared (SIR), one MPU-401 UART mode compatible MIDI/game interface, and a Smart Card Reader interface. Floppy disk connector. This connector accommodates the provided ribbon cable for the floppy disk drive. One side of the connector is slotted to prevent incorrect insertion of the floppy disk cable. IDE connectors. These dual-channel bus master IDE connectors support up to four Ultra DMA/100/66, PIO Modes 3 & 4 IDE devices. Both the primary (blue) and secondary (black) connectors are slotted to prevent incorrect insertion of the IDE ribbon cable.

Flash EEPROM. This 2Mb firmware contains the programmable BIOS program. South bridge controller. The fourth-generation Intel I/O Controller Hub (ICH4) is a subsystem that integrates various I/O functions including 2-channel ATA/100 bus master IDE controller, up to six USB 2.0/1.1 ports, I/O APIC, SMBus 2.0 controller, LPC interface, AC97 2.2 interface, PCI 2.2 interface, and integrated LAN controller. The ICH4 also contains the necessary arbitration and buffering for efficient utilization of these interfaces. ASUS ASIC. This chip performs several system functions that include hardware and system voltage monitoring. AGP slot. This Accelerated Graphics Port (AGP) slot supports 1.5V AGP4X mode graphics cards for 3D graphical applications. Standby power LED. This green LED lights up if there is a standby power on the motherboard. The LED acts as a reminder to turn off the system power before plugging or unplugging devices. Audio CODEC. The Realtek ALC650 is a 6-channel audio CODEC that is fully compliant with AC 97 2.2 specifications. The ALC650 provides a playback sampling rate of 96KHz and supports DVD applications. (on audio models only) PCI slots. These three 32-bit PCI 2.2 expansion slots support bus master PCI cards with 133MB/s maximum throughput. AGP warning LED. Serving as a smart burn-out protection for the motherboard, this red LED lights up if you plug in any 3.3V AGP card into the AGP slot. When this LED is lit, there is no way you can turn on the system power even if you press the power button. LAN PHY. This Intel 82562ET LAN PHY works with the integrated MAC in the South Bridge (ICH4) to fully support 10BASE-T/ 100BASE-TX Ethernet networking. (on LAN models only) PS/2 mouse port. This green 6-pin connector is for a PS/2 mouse. Parallel port. This 25-pin port connects a parallel printer, a scanner, or other devices. RJ-45 port. This port allows connection to a Local Area Network (LAN) through a network hub. (on LAN models only)
Line In jack. This Line In (light blue) jack connects a tape player or other audio sources. In 6-channel mode, the function of this jack becomes Rear Speaker Out. (on audio models only) Line Out jack. This Line Out (lime) jack connects a headphone or a speaker. In 6-channel mode, the function of this jack becomes Rear Speaker Out. (on audio models only) Microphone jack. This Mic (pink) jack connects a microphone. In 6-channel mode, the function of this jack becomes Bass/Center. (on audio models only) USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. Video port. This port is for a VGA monitor or other VGA-compatible devices. Serial port. This 9-pin COM1 port is for pointing devices or other serial devices. USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. PS/2 keyboard port. This purple 6-pin connector is for a PS/2 keyboard.

Chapter 2

This chapter describes the hardware setup procedures that you have to perform when installing system components. It includes details on the switches, jumpers, and connectors on the motherboard.

Hardware information

2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 Motherboard installation. 2-1 Motherboard layout.. 2-2 Before you proceed.. 2-3 Central Processing Unit (CPU). 2-4 System memory.. 2-10 Expansion slots.. 2-13 Switches and jumpers.. 2-16 Connectors... 2-20

Motherboard installation

Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. The P4B533-VM uses the microATX form factor that measures 9.6 in x 8.6 in (24.4 cm x 21.9 cm).
Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause you physical injury and damage motherboard components.
2.1.1 Placement direction
When installing the motherboard, make sure that you place it into the chassis in the correct orientation. The edge with external ports goes to the rear part of the chassis as indicated in the image below.

2.1.2 Screw holes

Place six (6) screws into the holes indicated by circles to secure the motherboard to the chassis.
Do not overtighten the screws! Doing so may damage the motherboard.
Place this side towards the rear of the chassis
PS/2KBMS T: Mouse B: Keyboard

Motherboard layout

21.9cm (8.6in)

KBPWR1 USBPWR2

CPU_FAN1

Bottom: USB20-3 USB20-4

Socket 478

Super I/O

IR_CON
DDR DIMM1 (64/72 bit, 184-pin module)

ATX Power Connector

PARALLEL PORT

FLOPPY

USBPWR1

Intel 845G

ATX12V1

CHA_FAN1

T: USB20_1 B: USB20_2

USB2.0 Top: RJ-45

Graphic Memory Controller Hub (GMCH)
Top:Line In Center:Line Out Below:Mic In

LAN PHY

DIMM1 DIMM2

SEC_IDE PRI_ IDE

FP_LINE_IN

FP_AUDIO

Accelerated Graphics Port (AGP)

AGP_WARN

SPDIF_OUT CD_IN1

SB_PWR

BCS2 BCS1

Audio Codec

PCI2 PCI3

J6 USB20_5 USB20_6 COM2

Intel I/O Controller Hub (ICH4)

BATTERY1

SMB 2.0

1. This feature requires a power supply that can provide at least 1A on the +5VSB lead when these jumpers are set to +5VSB. Otherwise, the system does not power up. 2. The total current consumed must NOT exceed the power supply capability (+5VSB) whether under normal condition or in sleep mode.

USBPWR2 USBPWR1 USBPWR3

+5V (Default)
P4B533-VM USB Device Wake Up

Connectors

This section describes and illustrates the internal connectors on the motherboard.
Always connect ribbon cables with the red stripe to Pin 1 on the connectors. Pin 1 is usually on the side closest to the power connector on hard drives and CD-ROM drives, but may be on the opposite side on floppy disk drives.
1. Hard disk activity LED (2-pin IDE_LED) This connector supplies power to the hard disk activity LED. The read or write activities of any device connected to the primary or secondary IDE connector cause this LED to light up.
TIP: If the case-mounted LED does not light, try reversing the 2-pin plug.

IDE_LED

P4B533-VM HDD Activity LED
2. Floppy disk drive connector (34-1 pin FLOPPY) This connector supports the provided floppy drive ribbon cable. After connecting one end to the motherboard, connect the other end to the floppy drive. (Pin 5 is removed to prevent incorrect insertion when using ribbon cables with pin 5 plug).
NOTE: Orient the red markings on the floppy ribbon cable to PIN 1.
P4B533-VM Floppy Disk Drive Connector
3. IDE connectors (40-1 pin PRI_IDE/SEC_IDE) This connector supports the provided UltraDMA/100/66 IDE hard disk ribbon cable. Connect the cables blue connector to the primary (recommended) or secondary IDE connector, then connect the gray connector to the UltraDMA/100/66 slave device (hard disk drive) and the black connector to the UltraDMA/100/66 master device. It is recommended that you connect non-UltraDMA/100/66 devices to the secondary IDE connector. If you install two hard disks, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. BIOS supports specific device bootup. If you have more than two UltraDMA/100/66 devices, purchase another UltraDMA/100/66 cable. You may configure two hard disks to be both master devices with two ribbon cables one for the primary IDE connector and another for the secondary IDE connector.
1. Pin 20 on each IDE connector is removed to match the covered hole on the UltraDMA cable connector. This prevents incorrect orientation when you connect the cables. 2. The hole near the blue connector on the UltraDMA/100/66 cable is intentional.

SEC_IDE

P4B533-VM IDE Connectors

PRI_IDE

NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1.
4. ATX power connectors (20-pin ATX_POWER1, 4-pin ATX12V) These connectors connect to an ATX 12V power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. In addition to the 20-pin ATXPWR connector, this motherboard requires that you connect the 4-pin ATX +12V power plug to provide sufficient power to the CPU.

13. Line in connector (5-pin FP_LINE_IN) (on audio models only) This connector is for a front panel Line In jack with a return path for automatic signal switching. By default, pins 1-2 and pins 2-3 are shorted with jumper caps to make the Line In source available from the rear panel Line In jack. Remove the jumpers caps if you wish to install the Intel front panel audio cable.
BLINE_IN_R LINE_IN_R AGND BLINE_LIN_L ALINE_LIN_L
P4B533-VM LINE_IN Connector
14. GAME/MIDI connector (16-1 pin GAME PORT1) This connector supports a GAME/MIDI module. If your package came with the optional USB 2.0/GAME module, connect the GAME/MIDI cable to this connector. The GAME/MIDI port on the module connects a joystick or a game pad for playing games, and MIDI devices for playing or editing audio files.
GND J1B2 J1CY GND GND J1CX J1B1 GND MIDI_IN J2B2 J2CY MIDI_OUT J2CX J2B1 GND

P4B533-VM Game Connector

15. Serial port 2 connector (10-1 pin COM2) This connector accommodates a second serial port using an optional serial port bracket. Connect the bracket cable to this connector then install the bracket into a slot opening at the back of the system chassis.
P4B533-VM Serial COM2 Bracket
16. System panel connector (20-pin ASUS_PANEL1) This connector is for various system front panel features. See the description of each feature below.

Keyboard Lock Power LED

PLED Keylock Ground +5 V

Speaker Connector

+5V Ground Ground Speaker
+5 V MLED ExtSMI# Ground PWR Ground

Message LED SMI Lead

Reset SW ATX Power Switch*
P4B533-VM System Panel Connectors
* Requires an ATX power supply.
System Power LED Lead (3-1 pin PLED) This 3-1 pin connector connects to the system power LED. The LED lights up when you turn on the system power, and blinks when the system is in sleep mode. System Warning Speaker Lead (4-pin SPEAKER) This 4-pin connector connects to the case-mounted speaker and allows you to hear system beeps and warnings.

Reset Ground

System Message LED Lead (2-pin MLED) This 2-pin connector is for the system message LED that indicates receipt of messages from a fax/modem. The normal status for this LED is OFF, when there is no incoming data signal. The LED blinks when data is received. The system message LED feature requires an ACPI OS and driver support. System Management Interrupt Lead (2-pin SMI) This 2-pin connector allows you to manually place the system into a suspend mode, or green mode, where system activity is instantly decreased to save power and to expand the life of certain system components. Attach the case-mounted suspend switch to this 2-pin connector. ATX Power Switch / Soft-Off Switch Lead (2-pin PWR) This connector connects a switch that controls the system power. Pressing the power switch turns the system between ON and SLEEP, or ON and SOFT OFF, depending on the BIOS or OS settings. Pressing the power switch while in the ON mode for more than 4 seconds turns the system OFF. Reset Switch Lead (2-pin RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting the system without turning off the system power.

Chapter 3

This chapter describes the power up sequence and gives information on the BIOS beep codes.

Powering up

3.1 3.2 Starting up for the first time. 3-1 Powering off the computer.. 3-2
Starting up for the first time
1. After making all the connections, replace the system case cover. 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: a. Monitor b. External SCSI devices (starting with the last device on the chain) c. System power (if you are using an ATX power supply, you need to switch on the power supply as well as press the ATX power switch on the front of the chassis). 6. After applying power, the power LED on the system front panel case lights up. For ATX power supplies, the system LED lights up when you press the ATX power switch. If your monitor complies with green standards or if it has a power standby feature, the monitor LED may light up or switch between orange and green after the system LED turns on. The system then runs the power-on tests. While the tests are running, the BIOS beeps or additional messages appear on the screen. If you do not see anything within 30 seconds from the time you turned on the power, the system may have failed a power-on test. Check the jumper settings and connections or call your retailer for assistance.

Award BIOS Beep Codes

Beep One short beep when displaying logo Long beeps in an endless loop One long beep followed by three short beeps High frequency beeps when system is working Meaning No error during POST No DRAM installed or detected Video card not found or video card memory bad CPU overheated; System running at a lower frequency
7. At power on, hold down <Delete> to enter BIOS Setup. Follow the instructions in Chapter 4.
Powering off the computer
You must first exit the operating system and shut down the system before switching off the power. For ATX power supplies, you can press the ATX power switch after exiting or shutting down the operating system. If you use Windows 95/98/2000/XP, click the Start button, click Shut Down, then click the OK button to shut down the computer. The power supply should turn off after Windows shuts down.
The message You can now safely turn off your computer does not appear when shutting down with ATX power supplies.

Chapter 4

This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.

BIOS setup

4.1 4.2 4.3 4.4 4.5 4.6 4.7 Managing and updating your BIOS. 4-1 BIOS Setup program.. 4-7 Main Menu.. 4-10 Advanced Menu.. 4-17 Power Menu.. 4-26 Boot Menu.. 4-32 Exit Menu.. 4-34

Managing and updating your BIOS
It is recommended that you save a copy of the motherboards original BIOS to a bootable floppy disk in case you need to reinstall the original BIOS later.
4.1.1 Using ASUS EZ Flash to update the BIOS
The ASUS EZ Flash feature allows you to easily update the BIOS without having to go through the long process of booting from a diskette and using a DOS-based utility. The EZ Flash is built-in the BIOS firmware so it is accessible by simply pressing <Alt> + <F2> right after the Power-On Self Tests (POST). Follow these steps to update the BIOS using ASUS EZ Flash. 1. Download the latest BIOS file from the ASUS website (see ASUS contact information on page x). Save the file to a floppy disk.
Write down the BIOS file name on a piece of paper. You need to type the exact BIOS file name at the EZ Flash screen.
2. Reboot the computer. 3. To use EZ Flash, press <Alt> + <F2> right after POST to display the following screen.
ASUS EZ Flash V1.00 Copyright (C) 2002, ASUSTeK COMPUTER INC. [Onboard BIOS Information] BIOS Version : ASUS P4B533 ACPI BIOS Revision 1002 BIOS Model : P4B533 BIOS Built Date : 04/16/02 Please Enter File Name for NEW BIOS: _ *Note: EZ Flash will copy file from A:\, Press [ESC] to reboot
The BIOS information in the above screen is for reference only. What you see on your screen may not be exactly the same as shown.
4. Insert the disk that contains the new BIOS file into the floppy drive. You will receive the error message, WARNING! Device not ready. if you proceed to step 5 without the disk in the drive.
5. At the prompt, Please Enter File Name for NEW BIOS: _, type in the BIOS file name that you downloaded from the ASUS website, then press <Enter>. EZ Flash will automatically access drive A to look for the file name that you typed. When found, the following message appears on screen.
[BIOS Information in File] BIOS Version: P4B533 Boot Block WARNING! Continue to update the BIOS (Y/N)? _
If you accidentally typed in a wrong BIOS file name, the error message, WARNING! File not found. appears. Press <Enter> to remove the message, then type in the correct file name. Press <Enter>. 6. At the above prompt, type Y to continue with the update process. Pressing N exits the EZ Flash screen and reboots the system without updating the BIOS. The following prompts appear if you typed Y.
Flash Memory: SST 49LF004 (Y/N)? _ (Y/N)? _
1. Update Main BIOS area 2. Update Boot Block area
7. Press Y for both items to completely update the main BIOS area and the boot block area.

1. Download an updated ASUS BIOS file from the Internet (WWW or FTP) (see ASUS CONTACT INFORMATION on page x for details) and save to the boot floppy disk you created earlier. 2. Boot from the floppy disk. 3. At the A:\ prompt, type AFLASH and then press <Enter>. 4. At the Main Menu, type 2 then press <Enter>. The Update BIOS Including Boot Block and ESCD screen appears. 5. Type the filename of your new BIOS and the path, for example, A:\XXX-XX.XXX, then press <Enter>. To cancel this operation, press <Enter>.
6. When prompted to confirm the BIOS update, press Y to start the update.
7. The utility starts to program the new BIOS information into the Flash ROM. The boot block is updated automatically only when necessary. This minimizes the possibility of boot problems in case of update failures. When the programming is done, the message Flashed Successfully appears.
8. Follow the onscreen instructions to continue.
If you encounter problems while updating the new BIOS, DO NOT turn off the system because this may cause boot problems. Just repeat the process, and if the problem persists, load the original BIOS file you saved to the boot disk. If the Flash Memory Writer utility is not able to successfully update a complete BIOS file, the system may not boot. If this happens, call the ASUS service center for support.

BIOS Setup program

This motherboard supports a programmable EEPROM that you can update using the provided utility described in section 4.1 Managing and updating your BIOS. Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to Run Setup. This section explains how to configure your system using this utility. Even if you are not prompted to use the Setup program, you may want to change the configuration of your computer in the future. For example, you may want to enable the security password feature or make changes to the power management settings. This requires you to reconfigure your system using the BIOS Setup program so that the computer can recognize these changes and record them in the CMOS RAM of the EEPROM. The EEPROM on the motherboard stores the Setup utility. When you start up the computer, the system provides you with the opportunity to run this program. Press <Delete> during the Power-On Self Test (POST) to enter the Setup utility, otherwise, POST continues with its test routines. If you wish to enter Setup after POST, restart the system by pressing <Ctrl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis. You can also restart by turning the system off and then back on. Do this last option only if the first two failed. The Setup program is designed to make it as easy to use as possible. It is a menu-driven program, which means you can scroll through the various sub-menus and make your selections among the predetermined choices.

Sub-menu

Note that a right pointer symbol (as shown on the left) appears to the left of certain fields. This pointer indicates that you can display a sub-menu from this field. A sub-menu contains additional options for a field parameter. To display a sub-menu, move the highlight to the field and press <Enter>. The sub-menu appears. Use the legend keys to enter values and move from field to field within a sub-menu as you would within a menu. Use the <Esc> key to return to the main menu. Take some time to familiarize yourself with the legend keys and their corresponding functions. Practice navigating through the various menus and sub-menus. If you accidentally make unwanted changes to any of the fields, use the set default hot key <F5> to load the Setup default values. While moving around through the Setup program, note that explanations appear in the Item Specific Help window located to the right of each menu. This window displays the help text for the currently highlighted field.

Main Menu

When you enter the Setup program, the following screen appears.

System Time [XX:XX:XX]

Sets the system to the time that you specify (usually the current time). The format is hour, minute, second. Valid values for hour, minute and second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). Use the <Tab> or <Shift> + <Tab> keys to move between the hour, minute, and second fields.

System Date [XX/XX/XXXX]

Sets the system to the date that you specify (usually the current date). The format is month, day, year. Valid values for month, day, and year are Month: (1 to 12), Day: (1 to 31), Year: (up to 2099). Use the <Tab> or <Shift> + <Tab> keys to move between the month, day, and year fields.
Legacy Diskette A [1.44M, 3.5 in.]
Sets the type of floppy drive installed. Configuration options: [None] [360K, 5.25 in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.] [2.88M, 3.5 in.]
Floppy 3 Mode Support [Disabled]
This is required to support older Japanese floppy drives. The Floppy 3 Mode feature allows reading and writing of 1.2MB (as opposed to 1.44MB) on a 3.5-inch diskette. Configuration options: [Disabled] [Enabled]
Supervisor Password [Disabled] / User Password [Disabled]
These fields allow you to set passwords. To set a password, highlight the appropriate field and press <Enter>. Type in a password then press <Enter>. You can type up to eight alphanumeric characters. Symbols and other characters are ignored. To confirm the password, type the password again and press <Enter>. The password is now set to [Enabled]. This password allows full access to the BIOS Setup menus. To clear the password, highlight this field and press <Enter>. The same dialog box as above appears. Press <Enter>. The password is set to [Disabled].

SDRAM RAS Precharge Delay [3T]
This item controls the idle clocks after issuing a precharge command to the DDR SDRAM.
SDRAM Active Precharge Delay [5T]
This item controls the number of DDR SDRAM clocks used for DDR SDRAM parameters.
SDRAM Idle Timer [Infinite]
Configuration options: [Infinite] [0T] [8T] [16T] [64T]

Onboard VGA [Disabled]

This field allows you to enable or disable the onboard VGA feature. Set to [Enabled] if you wish to use the onboard VGA. Set to [Disabled] if you installed an AGP device. If you did not install an external AGP device into the AGP slot, BIOS will enable the onboard VGA regardless of the setting of this field. Configuration options: [Disabled] [Enabled]
Graphics Aperture Size [128MB]
This feature allows you to select the size of mapped memory for AGP graphic data. Configuration options: [128MB] [256MB]

AGP Capability [4X Mode]

This motherboard supports the AGP 4X interface that transfers video data at 1066MB/s. AGP 4X is backward-compatible, so you may keep the default [4X Mode] even if you are using an AGP 1X video card. When set to [1X Mode], the AGP interface only provides a peak data throughput of 266MB/s even if you are using an AGP 4x card. Configuration options: [1X Mode] [4X Mode]
Video Memory Cache Mode [UC]
USWC (uncacheable, speculative write combining) is a new cache technology for the video memory of the processor. It can greatly improve the display speed by caching the display data. You must set this to UC (uncacheable) if your display card does not support this feature, otherwise the system may not boot. Configuration options: [UC] [USWC]
Memory Hole At 15M-16M [Disabled]
This field allows you to reserve an address space for ISA expansion cards. Setting the address space to a particular setting makes that memory space unavailable to other system components. Expansion cards can only access memory up to 16MB. Configuration options: [Disabled] [Enabled]
Delayed Transaction [Disabled]
When set to [Enabled], this feature frees the PCI bus when the CPU is accessing 8-bit ISA cards. This process normally consumes about 50-60 PCI clocks without PCI delayed transaction. Set this field to [Disabled] when using ISA cards that are not PCI 2.1 compliant. Configuration options: [Enabled] [Disabled]

Onboard PCI IDE [Both]

ACPI Suspend To RAM [Disabled]
This field allows you to enable or disable the ACPI Suspend-to-RAM feature. To support this feature, the +5VSB of the power supply should have the capacity to provide more than 720mA current. Configuration options: [Disabled] [Enabled]

Suspend Mode [Disabled]

Sets the time period before the system goes into suspend mode. Configuration options: [Disabled] [1~2 Min] [2~3 Min] [4~5 min] [8~9 Min] [20 Min] [30 Min]
PWR Button < 4 Secs [Soft Off]
When set to [Soft off], the ATX switch can be used as a normal system power-off button when pressed for less than 4 seconds. [Suspend] allows the button to have a dual function where pressing less than 4 seconds puts the system in sleep mode. Regardless of the setting, holding the ATX switch for more than 4 seconds powers off the system. Configuration options: [Soft off] [Suspend]

4.5.1 Power Up Control

AC PWR Loss Restart [Disabled]
This allows you to set whether or not to reboot the system after power interruptions. [Disabled] leaves your system off while [Enabled] reboots the system. [Previous State] sets the system back to the state it was before the power interruption. Configuration options: [Disabled] [Enabled] [Previous State]
Wake/Power Up On Ext. Modem [Disabled]
This allows either settings of [Enabled] or [Disabled] for powering up the computer when the external modem receives a call while the computer is in Soft-off mode. Configuration options: [Disabled] [Enabled]
The computer cannot receive or transmit data until the computer and applications are fully running. Thus, connection cannot be made on the first try. Turning an external modem off and then back on while the computer is off causes an initialization string that turns the system power on.
Power Up On PCI Card [Disabled]
When set to [Enabled], this parameter allows you to turn on the system through a PCI LAN or modem card. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Enabled]

Power On By PS/2 Keyboard [Space Bar]
This parameter allows you to use specific keys on the keyboard to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Space Bar] [Ctrl-Esc] [Power Key]
Power On By PS/2 Mouse [Disabled]
When set to [Enabled], this parameter allows you to use the PS/2 mouse to turn on the system. This feature requires an ATX power supply that provides at least 1A on the +5VSB lead. Configuration options: [Disabled] [Enabled]
Automatic Power Up [Disabled]
This allows an unattended or automatic system power up. You may configure your system to power up at a certain time of the day by selecting [Everyday] or at a certain time and day by selecting [By Date]. Configuration options: [Disabled] [Everyday] [By Date]

4.5.2 Hardware Monitor

CPU Q-Fan Function [Disabled]
This item allows you to enable or disable the ASUS Q-Fan feature that smartly adjusts the fan speeds for more efficient system operation. When this field is set to [Enabled], the CPU Temperature Threshold and CPU Fan Lowest Level Voltage items appear. Configuration options: [Disabled] [Enabled]
CPU Temperature Threshold
This item allows you to set the highest temperature for the CPU so that when exceeded by the actual CPU temperature, Q-Fan supplies more power to the CPU fan. When the CPU temperature goes below the setting, Q-Fan automatically reverts to the normal power supplied to the fan. Configuration options: [50C] [55C] [60C] [65C] [70C]
CPU Fan Lowest Level Voltage
This item allows you to set the lowest voltage applied to the CPU fan. Configuration options: [6V] [6.5V] [7V] [7.5] [8V] [8.5] [9V]
MB Temperature [xxxC/xxxF] CPU Temperature [xxxC/xxxF]
The onboard hardware monitor automatically detects and displays the motherboard and CPU temperatures.
CPU Fan Speed [xxxxRPM] or [N/A] Chassis Fan Speed [xxxxRPM] or [N/A]
The onboard hardware monitor automatically detects and displays the CPU, chassis, and power fan speeds in rotations per minute (RPM). If any of the fans is not connected to the motherboard, the specific field shows N/A.
VCORE Voltage, +3.3V Voltage, +5V Voltage, +12V Voltage
The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators.

Bus PCI AGP 1X AGP 2X AGP 4X Bus Frequency 33MHz 66MHz 66MHz 66MHz Bandwidth 33MHz 66MHz 133MHz 266MHz Data Transfer Rate 133MByte/sec 266MByte/sec 512MByte/sec 1024MByte/sec
Backup. A copy of a file, directory, or volume on a separate storage device from the original. This copy is for the purpose of data retrieval in case the original is accidentally erased, damaged, or destroyed. BIOS (Basic Input/Output System). BIOS is a set of routines that control how the computer transfers data between computer components, such as memory, disks, and the display adapter. The BIOS instructions are built into the computers read-only memory. BIOS parameters are configurable through the BIOS Setup program. You can update the BIOS using the AFLASH utility by copying a new BIOS file into the EEPROM. Bit (Binary Digit). Represents the smallest unit of data used by the computer. A bit can have one of two values: 0 or 1. Boot. Boot means to start the computer operating system by loading it into system memory. When the manual instructs you to boot your system (or computer), it means to turn ON your computer. Reboot means to restart your computer. When using Windows 95 or later, selecting Restart from Start | Shut Down. will reboot your computer. Bus Master IDE. PIO (Programmable I/O) IDE requires that the CPU be involved in IDE access and waiting for mechanical events. Bus master IDE transfers data to/from the memory without interrupting the CPU. Bus master IDE driver and bus master IDE hard disk drives are required to support bus master IDE mode. Byte (Binary Term). One byte is a group of eight contiguous bits. A byte is used to represent a single alphanumeric character, punctuation mark, or other symbol. Cache Memory. A type of RAM that allows a faster from the CPU than a regular RAM. The cache memory eliminates the CPU wait state. When the CPU reads data from the main memory, a copy of this data is stored in the cache memory. The next time the same address, the data is transferred from the cache memory instead of from the main memory. CODEC (Compressor/Decompressor). A software component that translates video or audio between its uncompressed form and the compressed form in which it is stored. COM Port. A connector with the accompanying circuitry that supports serial devices such as printers, mice, modems, and infrared modules. Each COM port is configured to use a different IRQ and address assignment. COM port is short for communication port, and is also called a serial port.

3 MSI 875P Neo LSR (MS6758) 875P (North Bridge) ICH5 (South Bridge) Intel 2.4CGHz (FSB 800) MSI (MS8907) (128M) FX5200 TDR128 Transcend 256MB DDR400 x 2

Motherboard

ASUS P4B533-VT 845G (North Bridge) ICH4 (South Bridge) Intel 2.4GHz (FSB 533) Gigabyte GV-AV64S-T (ATi RADEON 7000) Kingston 256MB DDR266
ASUS P4C800 875P (North Bridge) ICH5 (South Bridge) Intel 2.8CGHz (FSB 800) ASUS (V9520) (128M) FX5200 Transcend 256MB DDR400 x 2
Gigabyte GA-8KNXP 875P (North Bridge) ICH5R (South Bridge) Intel 2.6CGHz (FSB 800) PowerColor R95V-C3L (ATi RADEON R9500) Kingston 256MB DDR400 x 2
Gigabyte GA-8PE800Ultra 845PE (North Bridge) ICH4 (South Bridge) Intel 3.06GHz (FSB 533)

Chipset

Gainward GeForce4 MX440

Kingmax 512MB DDR333

Maxtor 40GB

Seagate 80G

Maxtor 80 GB (8M cache) 1. 2. 2. 4.

Seagate 80 GB

Maxtor 80 GB
GV600 V2.08A card GV800 V1.07 card GV900 V1.11 card GV1000 V1.11 card V5300 V5401 English Windows 2000 Windows XP 7 days (05/19~05/26) 18 days (1/15~2/2) Round-The-Clock Wavelet Mpeg4 Smart Record Technology NTSC PAL 320 x 240 V5300 V5400

GV600 V2.08 card

GV600 V2.11 card GV900 V1.11 card GV900-8 V1.11 card GV750 V1.07 card GV1000 V1.11+ DSP G1+GVA16 V5300 V5400 V6000 English Windows XP V5300
English Windows XP 12 days (05/27~06/08) 7 days (8/29~9/5) Round-The-Clock Wavelet M-Jpeg Smart Record Technology 230~240(GV900) 480(GV1000) NTSC

English Windows XP

English Windows 2000

Test Period

8 days (05/27~06/04)
7 days (05/23~05/30) 9 days (8/29~9/7) 22 days (1/16~2/7)

12 days (05/27~06/08)

Recording Mode CODEC

Round-The-Clock

Round-The-Clock Wavelet GeoMpeg4 240(GV900) 480(GV1000)
Wavelet Smart Record Technology

Frames / Sec

Video Source

Video Format

320 x channel(GV600) 4 channels(GV900)

320 x 240

320 x channel 4 channels 16 channels

4 channels

1 channel

3 channels

1024*768 Resolution
ASUS P4PE 845PE (North Bridge) ICH4 (South Bridge) Intel 3.06GHz (FSB 533) ASUS (V8170) (64M) GeForce4 MX440
Shuttle FS50 SIS 651 (North Bridge) SIS 961 (South Bridge) Intel 2.66GHz (FSB 533)
FREE TECH P8F533 845GE/GV (North Bridge) ICH4 (South Bridge) Intel 1.4GHz (FSB 400)
Gigabyte GA-8INXP E7205 (North Bridge) ICH4 (South Bridge) Intel 3.06GHz (FSB 533)
ASUS P4G8x E7205 (North Bridge) ICH4 (South Bridge) Intel 3.06GHz (FSB 533) ASUS V9280 GeForce4 Ti4200

VGA on Board

Albatron GeForce4 Ti4200

Kingston 512MB DDR200

Kingmax 256MB DDR400 X 2

Kingmax 512MB DDR333 x 2

IBM 80 GB

IBM 40 GB

Maxtor 60 GB 1. GV600 V2.11 card 2. GV650 V1.07 card 3. GV800 V3.01 + DSP G1+GVA16 1. V5300 2. V5301 3. V6000 English Server 2003 Windows XP GV800 GV750 GV650 GV600
IBM 80G V1.07 V1.07 V3.01 V3.01 card card card card
GV650 V1.07 card GV800 V1.07 card GV800 V1.07 card GV600 V3.01 card V5300 V6000 English Windows 2000 Windows XPsp1 V5300

GV600 V2.08A card

V5301 V6000 V6020 English Windows 2000 Windows XP 7 days (06/30~07/07) (07/15~07/21) 14 days (1/20~2/3) 12 days (4/24~5/6) Round-The-Clock Mpeg-4 GeoMpeg4 Smart Record Technology NTSC 320 x channels 3 channels 2 channels
7 days (05/28~06/04) 13days (1/16~1/29)

10 days (05/29~06/08)

7 days (05/29~06/05)
7 days 1. (06/16~06/23) 2. (07/15~07/22) 14days (1/20~2/3)
Round-The-Clock Wavelet GeoMpeg4 Smart Record Technology NTSC 320 x 240
Round-The-Clock Mpeg-4 GeoMpeg4 Smart Record Technology NTSC 320 x channel 2 channels
Wavelet Smart Record Technology NTSC 320 x 240

Video Source Video Format

2 channels

Micro system
14 MSI 875P Neo LSR MS 6758 875P (North Bridge) ICH5 (South Bridge) Intel 2.4CGHz (FSB 800) MSI FX5200 TDR-128 MS-8907
Gigabyte GA-8IK1100 875P (North Bridge) ICH5 (South Bridge) Intel 2.6CGHz (FSB 800) Winfast A310TD Nvidia FX5600
ASUS A7N8X-X N force Ultra400 (North Bridge) N force MCP (South Bridge) AMD XP2800+ Barton (FSB333) ELSA 534 Nvidia FX5200
Albatron PX 865PE Pro 865PE (North Bridge) ICH5 (South Bridge) Intel 2.8CGHz (FSB 800)
MSI 845PE MAX2-FIR Intel 845PE North Bridge 82801DB South Bridge Intel 2.4GHz (FSB 533) GAINWARD GeForce 3 Ti500 64MB

Albatron Giga FX5200P

A DATA A DATA 256MB DDR400 X 256MB DDR400 X 2 2
Kingston 256MB DDR400 X 2

TwinMos 256MB DDR400 X 2

Kingmax 256MB DDR333

Maxtor 80G

Maxtor 80 GB GV1000 V1.11 card GV900 V1.11 card V6000
Maxtor 60GB GV650 V3.01 + DSP G1 + GVA16 V6000
GV900 V1.11 card GV1000 V1.11 GV804 V3.00 card card V5400 V5400

GV1000 V1.11 card

English Windows XP 7 days (11/24~12/01/) 30 days (2/12~3/14 ) Round-The-Clock

English Windows 2000sp4

9 days (8/29~9/7)

14 days (8/29~9/12)

7 days (11/24~12/01)

8 days (1/28~2/5)

Round-The-Clock Wavelet M-Jpeg 230~240(GV900) 480(GV1000) NTSC 320 x channels

470~480(GV1000)

Wavelet Smart Record Technology NTSC 320 x channels

Geo-Mpeg4

Wavelet Smart Record Technology NTSC 640 x channels

477~480

475~480
Video Source Video Format Audio

NTSC 320 x x channels

NTSC 320 x channels
18 ASUS P4S-800 (SIS 648FX) SIS 648FX (North Bridge) SIS 963L (South Bridge) Intel 2.6CGHz (FSB 800)
19 Aopen XC cube (Micro system) Intel 865G (North Bridge) ICH 5 (South Bridge Intel 2.6CGHz (FSB 800)
AOPEN AX4GER-N Intel 845GE (North Bridge) ICH4 (South Bridge) Intel 2.4GHz (FSB 533)
Gigabyte GA-7NNXP N Force SPP (Ultra 400) (North Bridge) n Force MCP (South Bridge) AMD XP2800+ (Barton) PowerColor R96-C3 (RADEON 960 0)
GIGABYTE 8S655TX-ULTRA SIS 655TX (North Bridge) SIS 964 (South Bridge) Intel 2.6CGHz (FSB 800) MSI TD128 MS-8912 (FX5600)

Albatron GF4MX440SE-N

GIGABYTE GV-R9500

A DATA 256MB DDR400 X 2

Kingston Kingston 256MB DDR400 X 2 256MB DDR400 X 2
Maxtor 60GB GV600 V3.01 + GVA16 V6010

Maxtor 80GB

WD 120GB

Maxtor 120GB (8M)

HITACHI 120GB 8M *2 GV1000 V1.11 card+ DSP G1 +GVA16 V6000

GV600 V2.11

GV 250 V2.1D

GV800 V3.01 card

English Windows 2000 sp4

English Windows XPsp1

15 days (2/18~3/4)

8 days (12/10~12/17)

15 days (1/20 ~2/4)

9 days (1/7~1/16)

9 days (2/12~2/21)

Motion + WM

Mpeg4 Smart Record Technology NTSC 320 x channel
Geo-Mpeg4 Smart Record Technology PAL 320 x channel
Geo-Mpeg4 Smart Record Technology NTSC 320 x channel
Geo-Mpeg4 Smart Record Technology NTSC 640 x 480sw 4 channels
HP Desktop d330 Intel 865G (North Bridge) ICH 5 (South Bridge) Intel 2.6CGHz (FSB 800)
GIGABYTE 8IPE1000-L Intel 865PE (North Bridge) ICH 5R (South Bridge) Intel 2.8CGHz (FSB 800) ELSA F X 736- 128M ( F X 5700)
ASUS P4GE-V Intel 845GE (North Bridge) 82801DB (South Bridge) Intel 3.06CGHz (FSB 533)
CHAINTECH 9PJL Intel 865PE (North Bridge) ICH 5 (South Bridge) Intel 2.8CGHz (FSB 800) ASUS V9560/TD (FX5600)
GIGABYTE 8IG1000-Pro Intel 865G (North Bridge) ICH 5 (South Bridge) Intel 2.8CGHz (FSB 800)

Aopen GF4MX440SE-N

A DATA Kingston 256MB DDR400 X 256MB DDR400 X HITACHI 120GB 8M *1 Seagate 120GB(8M) *1 GV1000 V1.01 card GV 250 V2.2D V6000 V6020 Maxtor 120GB (8M) Maxtor(SATA) 160GB (8M) GV1000 V1.01 card+ DSP G1 +GVA16 GV650 V3.01 + DSP G1 V6000 V6020
Kingston A DATA 256MB DDR400 X 2 256MB DDR400 X 2

WD WD 300BB 80GB (8M)

HITACHI 120GB (8M)
HITACHI 120GB (8M) GV800 V3.01+ DSP G1 GV900 V1.11+ DSP G1 V6000 V6020

GV 600 V3.01

GV 800 v3.01
English Windows XPspdays (2/16~3/8) 16 days (4/19~5/5) Round-The-Clock
English Windows XPspdays (2/10~3/9) 11 days (4/22~5/3) Round-The-Clock
English Windows XPspdays (2/3~2/12) 15 days (4/10~4/25) Round-The-Clock Mpeg4 Geo-Mpeg4 Smart Record Technology NTSC 320 * channels

35 days (3/16~4/20)

9 days (3/22~3/31)
Mpeg4 Smart Record Technology NTSC 320 * channel
Geo-Mpeg4 Smart Record Technology PAL 320 * channels
470~480(GV1000) 470~480(GV1000) Smart Record Smart Record Technology Technology NTSC 320 x 240 None 1 channel PAL NTSC 320 x channels 1 channel
ASUS P4P800S Intel 848P (North Bridge) ICH 5 (South Bridge) Intel 2.8CGHz (FSB 800) GAINWARD GFTi4 800-SE 64M B TWIN MOS 512MB DDR400
ACER Veriton 7600G Intel 865G (North Bridge) ICH 5 (South Bridge) Intel 2.6CGHz (FSB 800)
ASUS T2 Intel 865G (North Bridge) ICH 5 (South Bridge) Intel 2.6CGHz (FSB 800)
GIGABYTE 8KNXP-ULTRA Intel 875P (North Bridge) ICH 5R (South Bridge) Intel 2.8CGHz (FSB 800) MSI FX5600XT-VTDR128 (FX5600XT) Kingston 256MB DDR400 *2
AOPEN AX4SPE-UN Intel 865PE (North Bridge) ICH 5 (South Bridge) P4 2.8C FSB 800 (Socket 478) ELSA 960XT-VIVO 128MB Kingston 256M *2 DDR400 Hitachi 120G(P-ATA) HDS722512VLAT20 Maxtor(S-ATA) 160GB (8M) 6Y160M0-1A GV1000 GV650 V6020 V6.1

TWIN MOS 256MB DDR400 *2

Kingston 256MB DDR400 *2

SEAGATE 120GB (8M)

GV804 V3.00
GV1000 V1.21 + GVA16 GV800 V3.01+ DSP G1+GVA16 V6020

GV800 V3.01

GV1000 V1.21 + DSP G1 + GVA16
English Windows XPspdays (4/9~4/22) 21 days (5/3~5/24)

E-Win-XPsp1

19 days (4/2~4/21)

26 days (3/16~4/11)

19 days (4/9~4/28)
12 Days (6/15~6/27) 10 Days (10/1~10/11)

Recording Mode

Round the clock
Geo-Mpeg4 Smart Record Technology NTSC 320 * channels
Geo-Mpeg4 465~480(GV1000) Smart Record Technology NTSC 320 * channels 4 channels
Mpeg4 Smart Record Technology NTSC 320 * channels
Geompeg4 465~480(GV1000) Smart Record Technology NTSC PAL 320*channels

475~480(GV1000)

NTSC 320 * channels
34 MSI 915G Combo-FR MS-7058 ver:1 Intel 915G (North Bridge) ICH 6R (South Bridge) LGA775 P4 3.0G (Socket T)
AOPEN AX45F-4DN SIS 655FX (North Bridge) SIS 964 (South Bridge) P4 2.8C FSB 800 (Socket 478) A OP E N FX5700- DV128 BUFFALO 256M *2 DDR400
ASUS P4P800-SE Intel 865PE (North Bridge) ICH 5R (South Bridge) P4 2.8EG FSB800 (Socket 478) L2 1MB ASUS A9550/TD/N/128M/ A (ATI9550) Transcend 256MB *2 DDR400
GIGABYTE 8I865PE-TW Intel 865PE (North Bridge) ICH 5 (South Bridge) P4 2.8EG FSB800 (Socket 478) L2 1MB GIGABYTE GV-R955128 D (ATI9550) Kingston 256MB *2 DDR400 Seagate 160GB(8M)SATA ST-3160023AS Seagate 160GB(8M)PATA ST-3160023A GV1000 V6.1
ASUS P5GDC-V Deluxe Intel 915G (North Bridge) ICH 6R (South Bridge) LGA775 3.0G (Socket T)

On board

Kingston 256MB *2 DDRII 533
A DATA 256MB *2 DDRII 533
Seagate 160GB(8M)PATA Seagate ST3160023A 160GB(8M)SATA 160GB(8M)SATA ST-3160023AS *2 ST-3160023AS GV1000 V6020 GV800 GV900+DSP V6.1
Seagate 160GB(8M)SATA ST-3160023AS *2

H/W S/W

GV1000 GV800S V6.1 V7040

GV1000 V6.1

12 Days (5/12~5/24)
10Days (8/7~8/17) 8 Days (8/18~8/26)

12 Days (8/13~8/25)

8 Days (9/22~9/30) 19Days (9/7 ~9/26)

11 Days (11/25~12/6)

Geompeg4 GV1000 (465~480) NTSC 320*240
Geompeg4 Smart Record Technology PAL 320*channels

Geompeg4

Geompeg4 GV1000 (465~480) GV800S (120) NTSC 320*240

GV1000 (465~480)

HITACHI Deskstar T7K250 250G(SATA II) GV650S V3.31 GV2008*1 V8020 V8110/V8120 E-Win-XP sp2

V8120 E-Vista

7 Days (9/15 ~ 9/22) 30 days (1/16 ~ 2/16)

11 (9/(1/25

Days ~ 10/3) Days ~ 2/15)

28 Days (8/30 ~ 9/28)

Geompeg4 GV800 120FPS GV1480 400FPS GV2008 240FPS NTSC / PAL 320*240 720*channels 8 channels
Geompeg4 H/W MPEG4 ASP GV650 60FPS GV2008*2 480FPS
Geompeg4 H/W MPEG2 GV650 60FPS GV2008 240FPS
Geompeg4 H/W MPEG4 ASP GV800 NTSC 120FPS PAL 100FPS GV2008*2 480FPS NTSC / PAL 320*240 720*channels

H/W MPEG4 ASP

GV2008*2 480FPS
NTSC / PAL 720*576 720*channels
NTSC / PAL 720*576 720*channels 8 channels

NTSC / PAL 720*channels

BIOS update to f8d Combo Card Driver required to solve V1544 or later GV combo card DSP required to solve overlay issue OS freeze issue.
ASUS P5W64 WS Professional Intel 975X (North Bridge) ICH7R (South Bridge) Intel Core2 Extreme processor QX6700
ASUS P5KC Intel P35 (North Bridge) ICH9 (South Bridge) LGA775 3.0G (E6850) (Socket T)
Supermicro C2SBE Intel P35 (North Bridge) ICH9 (South Bridge) LGA775 Core 2 Quad Q6600 (Socket T) ELSA NVIDIA 6600 LE
Gigabyte GA-P31-DS3L Intel P31 (North Bridge) ICH7 (South Bridge) LGA775 Core 2 Quad Q6600 (Socket T) MSI NX8500GT-TD256E -OC Kingstone DDRII-800 1G*2 HITACHI 160G HDS721616PLASEAGATE 320G ST3320620SV GV2008*2 V8200 E-Win-XP spdays (1/30 ~ 2/15)
Gigabyte GA-73PVM-S2H NVIDIA 7300 (North Bridge) NVIDIA 630i (South Bridge) LGA775 Core 2 Quad Q6600 (Socket T) On board
GIGABYTE Elsa GV-RX16P256D-RH 730GT 128B 3 2DT (ATI X1600) Kingstone DDRII 800 1G *2 ADATA 1G DDR2-800*2 SEAGATE 160G ST3160815SV SEAGATE 320G ST3320620SV GV2008*2 V8200 E-Win-XP spDay (12/14 ~ 1/10)
ADATA 1G DDR2-800*2 HITACHI 160G HDS721616PLA380 SEAGATE 320G ST3320620SV GV2008*2 V8200 E-Win-XP spdays (12/20 ~ 1/11)
Kingstone DDRII-800 1G*2 WD 160G WD1600AAJS SEAGATE 320G ST3320620SV GV1240 V8200 E-Win-XP spdays (11/28 ~ 12/14)

WD2500YS SATA2 *2

H/W S/W O/S
GV1480 GV2008*2 V8120 E-Win-XP spDays (5/15 ~ 6/6)
Geompeg4 H/W MPEG4 ASP GV1480 480FPS GV2008*2 480FPS NTSC / PAL 320*240 720*channels

480 FPS

240 FPS

NTSC 720*channels

NTSC 360*channels
DFI P35-T2RL Intel P35 (North Bridge) ICH9R (South Bridge)
Foxconn P35A Intel P35 (North Bridge) ICH9 (South Bridge)
Intel DG33BU Intel G33 (North Bridge) ICH9R (South Bridge)
ASUS P5KPL-VM Intel G31 (North Bridge) ICH7 (South Bridge)

Gigabyte GA-X38-DQ6 Intel X38 (North Bridge) ICH9R (South Bridge) LGA775 Core 2 Quad QX6850 (Socket T) Powercolor ATI1950 pro
LGA775 LGA775 LGA775 LGA775 Core 2 Quad Q6600 Core 2 Quad Q6600 Core 2 Quad Q6600 Core 2 Dual E4400 (Socket T) (Socket T) (Socket T) (Socket T) ASUS X2600XT 256M DDR4 MSI RX2600PRO-T2D25 6EZ/D3 Apcer DDRII-800 1G*2 WD 160G WD1600AAJS SEAGATE 320G ST3320620SV GV2008*2 V8200 E-Win-XP sp2
Apcer DDRII-800 1G*2 WD 160G WD1600AAJS SEAGATE 320G ST3320620SV GV804A GV2008*2 V8200 E-Win-XP spDays (11/29 ~ 12/14) 24 Days (12/14 ~ 1/6)
Apcer DDRII-800 1G*2 WD 160G WD1600AAJS SEAGATE 320G ST3320620SV GV1240 GV2008*2 V8200 E-Win-XP spDays (11/30 ~ 12/14) 24 Days (12/14 ~ 1/6)
ADATA 1G DDR2-800*2 SEAGATE 160G ST3160815SV SEAGATE 320G ST3320620SV GV1480 GV2008*2 V8200 E-Win-XP sp2 E-Vista Ultimate 25 Days (2/13 ~ 3/10) 27 Days (3/10 ~ 4/7)
Kingstone DDRII-800 1G*2 HITACHI 160G HDS721616PLA3 SEAGATE 320G ST3320620SV GV800 V4 GV2008*2 V8200 E-Win-XP sp2 E-Vista Ultimate 15 (3/(5/15 Days ~ 4/10) Days ~ 6/17)

25 Days (12/14 ~ 1/7)

Geompeg4 H/W MPEG4 ASP GV804A 120FPS GV2008*2 480FPS NTSC 320*240 720*channels
Geompeg4 H/W MPEG4 ASP GV1240 240FPS GV2008*2 480FPS NTSC 320*240 720*channels
Geompeg4 H/W MPEG4 ASP 480 FPS
Geompeg4 H/W MPEG4 ASP GV800V4 120FPS GV2008*2 480FPS NTSC / PAL 320*240 720*channels GV1480*2 + Enhance ENP-5150G power supply causes DSP live display error and video freeze,
NTSC 360*240 720*channels

77 Test180

79 Test189
80 Test193 Gigabyte GA-X48-DQ6 Intel X48 (North Bridge) ICH9R (South Bridge) Intel Core 2 QuadQ9450

81 Test195

ASUS P5E-VM HDMI Intel G35 (North Bridge) ICH9R (South Bridge) Intel Core 2 Duo E8400
ASUS P5E-VM DO Intel Q35 (North Bridge) ICH9 DO (South Bridge)
MSI G31M2-FD Intel G31 (North Bridge) ICH7 (South Bridge)
ASUS P5Q-E Intel P45 (North Bridge) ICH10R (South Bridge) Intel Core 2 QuadQ9300
LGA775 LGA775 Core 2 Quad Q6600 Core 2 Quad Q6600 (Socket T) (Socket T)