When using PCI cards on shared slots, ensure that the drivers support Share IRQ or that the cards do not need IRQ assignments. Otherwise, conflicts will arise between the two PCI groups, making the system unstable and the card inoperable.

2.6.3 PCI slots

There are six 32-bit PCI slots in this motherboard. The slots support PCI cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. The following figure shows a LAN card installed on a PCI slot.

Figure 2-18

Installed PCI Card

2.6.4 AGP slot

This motherboard has an Accelerated Graphics Port (AGP) slot that supports +1.5V AGP cards. When you buy an AGP card, make sure that you ask for one with +1.5V specification. Note the notches on the card golden fingers to ensure that they fit the AGP slot on your motherboard. If you installed an incorrect AGP card, such as a SiS305-based AGP card or any other 3.3V AGP card, the onboard red LED (LED2) lights up, an indication that the card is not supported on the motherboard. As long as this LED is lighted, you cannot turn on the system power even if you press the power button, thus preventing permanent damage to the motherboard.
Install only 1.5V AGP cards on this motherboard!

Keyed for 1.5v

P4B-E Accelerated Graphics Port (AGP)

Figure 2-19

Accelerated Graphics Port (AGP) Slot Location

2.6.5 CNR slot

The Communications and Networking Riser (CNR) slot supports interface cards that integrates audio, modem, and network functionality. The CNR specification supports interfaces including: Audio Codec 97 (AC 97) - for audio and/or modem functions Local Area Network (LAN) - for networking functions Universal Serial Bus (USB) - for functions implemented in the USB interface, and technologies such as broadband, DSL, and wireless System Management Bus (SMB) - for Plug-n-Play functionality Power - to provide the signals required for power management, and the main power supplies to operate the CNR circuitry The CNR is tagged to replace the current Audio Modem Riser (AMR) slot because of its flexibility and added features. Also, the CNR slot does not take up the motherboard space for one PCI slot because it is a shared slot; rather, it provides you more options.

Make sure that your ATX 12V power supply can provide 8A on the +12V lead and at least 1A on the +5-volt standby lead (+5VSB). The minimum recommended wattage is 230W, or 300W for a fully configured system. The system may become unstable and may experience difficulty powering up if the power supply is inadequate.

ATXPWR

+12.0VDC +5VSB PWR_OK COM +5.0VDC COM +5.0VDC COM +3.3VDC +3.3VDC +5.0VDC +5.0VDC -5.0VDC COM COM COM PS_ON# COM -12.0VDC +3.3VDC

ASUS EZ Plug (AUX+12V)

+5V GND GND +12V

+12V DC COM

P4B-E ATX & Auxiliary Power Connectors

Figure 2-42

Power Supply Connectors
9. Internal audio connectors (4-pin CD, AUX, MODEM) (on audio models only) These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, or MPEG card. The MODEM connector allows the onboard audio to interface with a voice modem card with a similar connector. It also allows the sharing of mono_in (such as a phone) and a mono_out (such as a speaker) between the audio and a voice modem card.

AUX (White) CD (Black)

Right Audio Channel Ground Ground Left Audio Channel
Modem-Out Ground Ground Modem-In
P4B-E Internal Audio Connectors

Figure 2-43

Internal Audio Connectors
10. Internal microphone connector (3-pin INT_MIC) (on audio models only) This connector connects to an optional front panel audio module using a 3-pin audio cable. If your chassis has this audio module, you can connect a microphone to the front panel connector.
The front panel microphone may not work properly when there is another microphone connected to the Microphone (pink) jack on the rear panel. You may only use one microphone at a time.

INT_MIC

MIC Power MIC Input Ground
P4B-E Internal Microphone Connector

Figure 2-44

Internal Microphone Connector
11. Headphone true-level line out connector (3-pin HPHONE) (on audio models only) This connector connects to an optional front panel audio module using a 3-pin audio cable. If your chassis has this audio module, you can connect a headphone/speaker to the front panel connector.

Reset Ground

ATX Power Switch / Soft-Off Switch Lead (2-pin PWRSW) This connector connects a switch that controls the system power. Pressing the power switch turns the system between ON and SLEEP, or ON and SOFT OFF, depending on the BIOS or OS settings. Pressing the power switch while in the ON mode for more than 4 seconds turns the system OFF. Reset Switch Lead (2-pin RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting the system without turning off the system power.

Chapter 3

This chapter describes the power up sequence and gives information on the BIOS beep codes.

Powering up

Starting up for the first time
1. After making all the connections, replace the system case cover. 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: a. Monitor b. External SCSI devices (starting with the last device on the chain) c. System power (if you are using an ATX power supply, you need to switch on the power supply as well as press the ATX power switch on the front of the chassis). 6. After applying power, the power LED on the system front panel case lights up. For ATX power supplies, the system LED lights up when you press the ATX power switch. If your monitor complies with green standards or if it has a power standby feature, the monitor LED may light up or switch between orange and green after the system LED turns on. The system then runs the power-on tests. While the tests are running, the BIOS beeps or additional messages appear on the screen. If you do not see anything within 30 seconds from the time you turned on the power, the system may have failed a power-on test. Check the jumper settings and connections or call your retailer for assistance.

Award BIOS Beep Codes

One short beep when displaying logo Long beeps in an endless loop One long beep followed by three short beeps High frequency beeps when system is working

Meaning

No error during POST No DRAM installed or detected Video card not found or video card memory bad CPU overheated; System running at a lower frequency
You will not hear the BIOS beeps when the ASUS POST Reporter is enabled. You will hear the vocal POST messages instead.
7. At power on, hold down <Delete> to enter BIOS Setup. Follow the instructions in Chapter 4. ASUS P4B-E motherboard user guide 3-1

Vocal POST Messages

This motherboard includes the Winbond speech controller to support a special feature called the ASUS POST Reporter. This feature gives you vocal POST messages and alerts to inform you of system events and boot status. In case of a boot failure, you will hear the specific cause of the problem. These POST messages are customizable using the Winbond Voice Editor software that came with your package. You can record your own messages to replace the default messages. Following is a list of the default POST messages and their corresponding actions, if any. POST Message

Onboard Card Reader Type [Disabled]
This field allows you to select the appropriate card reader type to match your device if you installed one. Keep the default setting [Disabled] if you did not install any. Configuration options: [Disabled] [Memory Stick] [Secure Digital]
Onboard AC97 Audio Controller [Auto] Onboard AC97 Modem Controller [Auto]
[Auto] allows the BIOS to detect whether you are using any modem/audio device. If a modem/audio device is detected, the onboard modem/audio controller is enabled; if no modem/audio device is detected, the controller is disabled. If there are conflicts with the onboard modem/audio controller, set the appropriate field to [Disabled]. Configuration options: [Disabled] [Auto]
Speech POST Reporter [Enabled]
This field enables or disables the ASUS POST Reporter feature. See section 1.4 Special Features and 3.2 Vocal POST messages for more information. Configuration options: [Disabled] [Enabled]

4.4.3 PCI Configuration

Slot 1/5, Slot 2, Slot 3, Slot 4, Slot 6 IRQ [Auto]
These fields automatically assign the IRQ for each PCI slot. The default setting for each field is [Auto], which utilizes auto-routing to determine IRQ assignments. Configuration options: [Auto] [NA] [3] [4] [5] [7] [9] [10] [11] [12] [14] [15]
PCI/VGA Palette Snoop [Disabled]
Some non-standard VGA cards, like graphics accelerators or MPEG video cards, may not show colors properly. Setting this field to [Enabled] corrects this problem. If you are using standard VGA cards, leave this field to the default setting [Disabled]. Configuration options: [Disabled] [Enabled]

PCI Latency Timer [32]

Leave this field to the default setting [32] for best performance and stability.

USB Function [Both]

This motherboard supports Universal Serial Bus (USB) devices. Set this field to [Primary] or [Both] if you want to connect USB devices. Configuration options: [Disabled] [Primary] [Both]]
Primary VGA BIOS [PCI VGA Card]
This field allows you to select the primary graphics card. Configuration options: [PCI VGA Card] [AGP VGA Card]
Onboard LAN Boot ROM [Disabled]
This field allows you to enable or disable the option ROM in the onboard LAN chipset. Configuration options: [Disabled] [Enabled]]
Onboard ATA Device First [Yes]
This field allows you to select the onboard ATA or a SCSI device. The default setting [Yes] selects the onboard ATA device. Selecting the option [No] selects the SCSI device. Configuration options: [No] [Yes]]
4.4.3.1 PCI IRQ Resource Exclusion

IRQ XX Reserved [No/ICU]

These fields indicate whether or not the displayed IRQ for each field is being used by a legacy (non-PnP) ISA card. The setting [No/ICU] for an IRQ field indicates that you are using the ISA Configuration Utility (ICU), and that this particular IRQ is NOT required by a legacy ISA card. Set the IRQ field to [Yes] if you install a legacy ISA card that requires a unique IRQ and you are NOT using ICU. Configuration options: [No/ICU] [Yes]

Power Menu

The Power menu allows you to reduce power consumption. This feature turns off the video display and shuts down the hard disk after a period of inactivity.
Power Management [User Defined]
This field allows you to activate or deactivate the automatic power saving features. When set to [Disabled], the power management features do not function regardless of the other settings on this menu. The [User Defined] option allows you to set the period of inactivity before the system enters suspend mode. Refer to Suspend Mode later in this section. When set to [Max Saving], system power is conserved to its greatest amount. This setting automatically puts the system into suspend mode after a brief period of system inactivity. [Min Saving] allows the least power saving as the system enters suspend mode only after a long period of inactivity. Configuration options: [User Defined] [Disabled] [Min Saving] [Max Saving]
You should install the Advanced Power Management (APM) utility to keep the system time updated even when the computer enters suspend mode. In Windows 3.x and Windows 95, you need to install Windows with the APM feature. In Windows 98 or later, APM is automatically installed as indicated by a battery and power cord icon labeled Power Management in the Control Panel. Select the item Advanced in the Power Management Properties dialog box.
Video Off Option [Suspend -> Off ]
This field determines when to activate the video off feature for monitor power management. Configuration options: [Always On] [Suspend -> Off]
Video Off Method [DPMS OFF]
This field defines the video off features. The Display Power Management System (DPMS) feature allows the BIOS to control the video display card if it supports the DPMS feature. [Blank Screen] only blanks the screen. Use this for monitors without power management or green features.
Even if installed, your screen saver does not display when you select [Blank Screen] for the above field.
[V/H SYNC+Blank] blanks the screen and turns off vertical and horizontal scanning. Configuration options: [Blank Screen] [V/H SYNC+Blank] [DPMS Standby] [DPMS Suspend] [DPMS OFF] [DPMS Reduce ON]
HDD Power Down [Disabled]
Shuts down any IDE hard disk drives in the system after a period of inactivity as set in this user-configurable field. This feature does not affect SCSI hard drives. Configuration options: [Disabled] [1 Min] [2 Min] [3 Min].[15 Min]
ACPI Suspend To RAM [Disabled]
This field allows you to enable or disable the ACPI Suspend-to-RAM feature. To support this feature, the +5VSB of the power supply should have the capacity to provide more than 720mA current. Configuration options: [Disabled] [Enabled]

Suspend Mode [Disabled]

Sets the time period before the system goes into suspend mode. Configuration options: [Disabled] [1~2 Min] [2~3 Min] [4~5 min] [8~9 Min] [20 Min] [30 Min]

Boot Virus Detection [Enabled]
This field allows you to set boot virus detection, ensuring a virus-free boot sector. The system halts and displays a warning message when it detects a virus. If this occurs, you can either allow the operation to continue or use a virus-free bootable floppy disk to restart and investigate your system. Configuration options: [Disabled] [Enabled]
Quick Power On Self Test [Enabled]
This field speeds up the Power-On-Self Test (POST) routine by skipping retesting a second, third, and fourth time. Configuration options: [Disabled] [Enabled]
Boot Up Floppy Seek [Enabled]
When enabled, the BIOS will seek the floppy disk drive to determine whether the drive has 40 or 80 tracks. Configuration options: [Disabled] [Enabled]
Full Screen Logo [Enabled]
This allows you to enable or disable the full screen logo display feature. Configuration options: [Disabled] [Enabled]
Make sure that the above item is set to [Enabled] if you wish to use the ASUS MyLogo feature.

Interrupt Mode [APIC]

The Advanced Programmable Interrupt Controller (APIC) setting allows you to distribute interrupt routings other than the 16 IRQs. The Programmable Interrupt Controller (PIC) setting allows you to use the 16 IRQs only. Configuration options: [PIC] [APIC] 4-30 Chapter 4: BIOS Setup

Exit Menu

When you have made all of your selections from the various menus in the Setup program, save your changes and exit Setup. Select Exit from the menu bar to display the following menu.
Pressing <Esc> does not immediately exit this menu. Select one of the options from this menu or <F10> from the legend bar to exit.

Exit Saving Changes

Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. The CMOS RAM is sustained by an onboard backup battery and stays on even when the PC is turned off. When you select this option, a confirmation window appears. Select [Yes] to save changes and exit.
If you attempt to exit the Setup program without saving your changes, the program prompts you with a message asking if you want to save your changes before exiting. Pressing <Enter> saves the changes while exiting.

Exit Discarding Changes

Select this option only if you do not want to save the changes that you made to the Setup program. If you made changes to fields other than system date, system time, and password, the BIOS asks for a confirmation before exiting.

Load Setup Defaults

This option allows you to load the default values for each of the parameters on the Setup menus. When you select this option or if you press <F5>, a confirmation window appears. Select [Yes] to load default values. Select Exit Saving Changes or make other changes before saving the values to the non-volatile RAM.

Discard Changes

This option allows you to discard the selections you made and restore the previously saved values. After selecting this option, a confirmation appears. Select [Yes] to discard any changes and load the previously saved values.

Save Changes

This option saves your selections without exiting the Setup program. You can then return to other menus and make further changes. After you select this option, a confirmation window appears. Select [Yes] to save any changes to the non-volatile RAM.

Chapter 5

This chapter describes the contents of the support CD that comes with the motherboard package.

Software support

Install an operating system
This motherboard supports Windows 98/ME/NT/2000/XP and OS/2 operating system (OS). Always install the latest OS version and corresponding updates so you can maximize the features of your hardware. Because motherboard settings and hardware options vary, refer to your OS documentation for detailed installation insructions.
Before installing Windows NT/2000/XP operating system, make sure to copy the specific Promise RAID/ATA100 drivers for your OS from the support CD to a floppy disk. TIP: From the folders DRIVERS/PROMISE/RAID/SETUP, click on MakeDisk to automatically copy the RAID drivers into the floppy disk. Install the RAID/ATA100 drivers from the floppy disk. You cannot install these drivers directly from the support CD. The RAID drivers are in the folders DRIVERS/PROMISE/RAID. The ATA100 drivers are in the folders DRIVERS/PROMISE/ATA100.

Support CD information

The support CD that came with the motherboard contains useful software and several utility drivers that enhance the motherboard features.
The contents of the support CD are subject to change at any time without notice. Visit the ASUS website for updates.
5.2.1 Running the support CD
To begin using the support CD, simply insert the CD into your CD-ROM drive. The CD automatically displays the welcome screen and the installation menus if Autorun is enabled in your computer.
If the welcome screen did not appear automatically, locate and doubleclick on the file ASSETUP.EXE from the BIN folder in the support CD to display the menus.

5.2.2 Main menu

From the welcome screen, the program takes you directly to the main menu. The main menu displays an image of the motherboard, and the buttons and icons that link you to the software, drivers, utilities, and other information contained in the support CD.

Place your mouse cursor on an icon and click to display the specified item
Click on a button to display the available options
Chapter 5: Software support

5.2.3 Software menu

The software menu shows the applications and other software that the motherboard supports. The highlighted items indicate that they are available for your motherboard. Simply click on a specific item then follow the installation wizard to install it. The software menu is composed of two screens. Click on the Next button on the lower right corner of the first screen to display the second menu screen. To return to the first menu screen, click on the Back button on the lower right corner of the second screen.

ASUS Update

This program allows you to download the latest version of the BIOS from the ASUS website.
Before using the ASUS Update, make sure that you have an Internet connection so you can connect to the ASUS website.
The ASUS Update includes a new feature called ASUS MyLogo. This feature allows you to get rid of the boring boot up screens by customizing your own boot logo. Refer to section 5.3 Software information for setup instructions.
Intel LDCM Administrator Setup
This program is for monitoring PC systems on the network within the same bridge as the installed Client software.
The administrator should install both the Administrator and the Client software.

Intel LDCM Client Setup

This program is for monitoring the Client system. Install the LANDesk Client Manager to use the hardware manager features.

ASUS BIOS Flash Utility

This utility allows you to remotely flash the Client PCs BIOS when used with the Intel LDCM Administrator.

ASUS PC Probe

This smart utility monitors the fan speed, CPU temperature, and system voltages, and alerts you on any detected problems. This utility helps you keep your computer at a healthy operating condition.

Winbond Voice Editor

This program is for recording and customizing wave files for the ASUS POST Reporter. Use this program if you wish to change the default vocal POST messages. See section 3.2 Vocal POST messages for a list of the default messages.

Cyberlink Video and Audio Applications
This item installs the Cyberlink PowerPlayer SE 5.0 and Cyberlink VideoLive Mail 4.0.

Direct X

This item installs the Microsoft V8.0a driver.

PC-cillin

This item installs the PC-cillin 2000 V7.61 anti-virus software. View the PC-cillin online help for detailed information.
The above PC-cillin version supports Windows XP operating system and maintains backward compatibility with Windows 95.

Acrobat Reader

This item installs the Adobe Acrobat Reader V5.0. The Acrobat Reader software is for viewing files saved in Portable Document Format (PDF).

E-Color 3Deep

This item installs the 3Deep software. 3Deep is the first application that gives online gamers the competitive edge in multi-player skirmishes. This application removes dark washed-out graphics to deliver true vibrant colors.

ASUS Screen Saver

This item installs the ASUS screen saver. 5-4 Chapter 5: Software support

5.2.4 Drivers menu

The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. The drivers menu is composed of two screens. Click on the Next button on the lower right corner of the first screen to display the second menu screen. To return to the first menu screen, click on the Back button on the lower right corner of the second screen.

INF Driver

This item installs the Intel Chipset Software Installation Utility that enables Plug-n-Play INF support for Intel chipset components. This utility installs to the target system the Windows INF files that outline to the operating system how the chipset components will be configured. You may install this utility in three modes: interactive, silent, and unattended preload. The interactive mode requires user input during installation. This is not required in the silent and unattended preload modes. Refer to the online help or readme file that came with the utility.
Intel Application Accelerator
This item installs the Intel Application Accelerator for Microsoft Windows 98/98SE/ME/NT4.0/2000. This program is designed to improve performance of the storage sub-system and overall system performace.
Install the INF Driver before installing the Intel Application Accelerator.

LAN (optional)

This item installs the RealTek PCI Fast Ethernet driver.
This item installs the C-Media 6-channel PCI audio driver. Refer to 5.3.5 Multi-Channel audio Feature on page 5-18 for setup instructions.

Smart Card Reader

This item installs the Smart Card Reader device driver.
This item installs the RAID 0/RAID 1 device driver.
Make sure that you enable the RAID jumpers if you wish to use the RAID feature. See page 2-23.
Winbond Memory Stick Storage Device Driver
This item installs the Memory Stick (MS) device driver. The device driver allows you to use the MS for securely downloading and storing digital files and other data.

If you selected the option to update the BIOS from a file, a window pops up prompting you to locate the file. Select the file, click Save, then follow the screen instructions to complete the update process.

5.3.2 ASUS MyLogo

The ASUS MyLogo is automatically installed when you install the ASUS Update utility from the software menu. See section 5.2.3 Software menu.
Before using ASUS MyLogo feature, use the AFLASH utility to make a copy of your original BIOS file, or obtain the latest BIOS version from the ASUS website.
Follow these steps to use ASUS MyLogo. 1. Launch the ASUS Update utility. See section 5.3.1 ASUS Update. 2. When prompted for the BIOS update method, select the option Update BIOS from a file. 3. Specify the location of the BIOS file, such as from a floppy disk. Click Next.
4. From the selection that appears, choose a logo image. Click Next. NOTE: If you wish, you may create your own boot logo image in GIF, JPG, or BMP file formats.
5. When you click on an image, it displays larger on the MyLogo screen.
6. The next screen prompts you to flash the original BIOS to update it with the new boot logo. Click Flash to update the BIOS. 7. When finished, click Exit, then reboot your computer. Your system boots with the new boot logo.
Instead of starting from ASUS Update, you may also launch ASUS MyLogo directly from the Windows Start menu to change your BIOS boot logo. After you have modified the BIOS file with the new logo, use the ASUS Update utility to upload the new BIOS into the EEPROM.
5.3.3 Personalized Boot Logo
Also included in the support CD is a DOS version of ASUS MyLogo. Locate the application called LOGO.EXE and a sample image library of boot screens in bitmap (BMP) format to install this feature.
Back up your system BIOS to a bootable floppy disk before using LOGO.EXE to modify your boot screen. See section 4.1 Managing and updating your BIOS. Make sure that the item Full Screen Logo in BIOS is set to [Enabled].
1. To set up a new Personalized Boot Logo, browse the Support CD and copy these three components to the windows directory: LOGO.EXE; AFLASH.EXE; one or more BMP files in 640 x 480 pixel, 16-color format. 2. Then go to the Shut Down Menu and select: Restart in DOS Mode. From the DOS prompt, run AFLASH: C:\WINDOWS>AFLASH 3. In AFLASH, select [1] and save the existing system BIOS file with a new name, for example: CSCB1016.AWD. Exit AFLASH to DOS. 4. To set up a new boot screen, run LOGO from DOS. Both the BIOS file name and the BMP file name must follow in the command line: C:\WINDOWS>LOGO CSCB1016.AWD SEA2.BMP 5. Press <Enter> to save the image with the BIOS file. 6. Run AFLASH again. Select [2] and flash the updated BIOS file, in this case, CSCB1016.AWD, to the ROM. 7. Reboot your computer by pressing <Ctl><Alt><Del>. The new boot screen that you selected appears. If you wish to select a new BMP file, re-run the process from Step 4. You may wish to create an original boot image. Use your favorite photo editor to save an image as a 640 x 480 pixel, 16-color BMP file. Choose a file name for the image with eight digits and characters recognizable in the DOS environment.

7. Click a POST event on the Voice Editor screen, then on the Edit button. The Event Sound Editor window appears. 8. Locate and select your wave file for the event then click on the arrow opposite Voice1. The file you selected appears on the space next to it. 9. Click OK to return to the Voice Editor screen. 10. Do steps 7 to 9 for the other events. 11. When done, click the Save button. A window appears prompting you to save your configuration. 12. Type a file name with a.flh extension, then click Save. 13. Click on the Write button to compress the file and copy into the EEPROM. 14. Click Yes on the confirmation window that appears.
If you receive an error message telling you that the files exceed the total allowable size, do one or all of the following. Try to modify your messages to make them shorter Save the wave files at a lower quality Skip lesser used events like FDD Detection, IDE HDD Detection, etc.
5.3.5 Multi-Channel Audio Feature
The C-Media PCI Audio Driver and Applications are included in the Support CD that came with your motherboard package. Install these programs to enable the multi-channel audio feature.
You must use 4 or 6 channel speakers for this setup.
Setting the C-Media Audio Mixer
1. Install the C-Media 6-channel PCI audio driver from the support CD. 2. After installation, the C-Media Mixer icon appears on the bottom right of the screen.

Mixer Icon

3. Click on the mixer icon to display the C-Media Audio Mixer.

Advanced Button

You may also launch the Mixer by clicking on the Start button on your Windows desktop, then select
Programs/PCI Audio Applications/ Mixer/Audio Rack.
4. Click on the Advanced button on the Mixer to display the Speaker, Volume, Sound Effects, and Options menus.
Make sure that the BCS1/BCS2 jumpers are set correctly before using the 6-channel audio feature. See page 2-22 for the settings.
Running the C-Media Audio Demo Program
The C-Media audio demo program allows you to test and fine tune your speaker system. To launch the the multi-channel audio demo program, click on Start from your desktop, then select PCI Audio Applications/ Multi-Channel Audio Demo. From the demo program interface, click on Help to display the instructions and hardware diagrams for configuring and testing your speaker system.

TV Box

To configure your speakers, launch the Speaker Channel Configuration menu by clicking on the TV Box on the program interface.

Expansion card installation 2-13 IRQ assigments 2-14 Expansion slots 1-5, 2-13 AGP 1-5 CNR 1-4 PCI 1-5 E-Color 3Deep 5-4
Keyboard Auto-Repeat Delay 4-13 Auto-Repeat Rate 4-13 Features 4-13
Flash EEPROM 1-4 Floppy 3 Mode 4-8

Legacy Diskette 4-8

Hard Disk Drives (HDDs) CHS Capacity 4-11 Cylinders 4-11 Heads 4-11 LBA Capacity 4-11 Primary/Secondary Master 4-9 Primary/Secondary Slave 4-9 Sectors 4-11 Types 4-9 Hardware Monitor 4-28 Heatsink installation 2-7 Heatsink retention module 1-7
Motherboard components 1-2 IRQ table 2-14 layout 2-2 placement 2-1 screws 2-1 Multi-Sector Transfers 4-11
Onboard LEDs 2-3 Operating system installation 5-1 Overclocking features 1-8
Interrupt Assignments 2-14 IRQ assignments 2-14
Parallel Port 1-5, 4-21 Modes 4-21 Password Supervisor 4-14 User 4-14 PC-cillin 5-4 PCI Configuration 4-22 PCI Latency Timer 4-22 PCI/VGA Palette Snoop 4-22 PIO Mode 4-12 Plug & Play O/S 4-30 Power Management 4-24 Power On Self Test 4-30 POST Messages 3-2 customizing 5-16 PS/2 Keyboard Port 1-5 PS/2 Mouse Port 1-5 PS/2 Mouse Function Control 4-17
Super I/O chipset 1-4 Support CD 5-1 ASUS Update 5-3 Boot Logo 5-13 DOS Utilities 5-7 Drivers menu 5-5 Main menu 5-2 motherboard information 5-8 readme file 5-9 Software menu 5-3 Technical Support Form 5-9 Welcome screen 5-1 Winbond Voice Editor 5-14 Suspend Mode 4-25 System Controller North Bridge 1-3 South Bridge 1-3 System Date 4-8 System memory configurations 2-10 System Time 4-8

Retention Mechanism 2-8

UART2 4-22 Ultra DMA Mode 4-12 USB Legacy Support 4-17 USB ports 1-5 USWC 4-19
SCSI BIOS 4-22 SDRAM Active to Precharge Time 4-18, 19 V CAS Latency 4-18 Configuration 4-18 Video Memory 4-19 RAS Precharge Time 4-18 Z RAS to CAS Delay 4-18 Serial Ports 1-5, 4-20 ZIF socket 2-4 Slots AGP 2-15 CNR 2-16 PCI 2-15 Smart Card Reader 2-35 SMART Monitoring 4-12 SPDIF audio 2-33

PlusSOYOSYK7VEMProSOYOSYK7VIASOYOSYK7VLMBSOYOSYK7VTAProSOYO SYP4VAL(VersionM)SOYOSYP4VGASOYOSYTISUSupermicro370DDESupermicro 370SSA/370SSE/370SSM/370SSRSupermicroP3TSSE/P3TSSA/P3TSSRSupermicro P4SBA+/P4SBA/P4SBE/P4SBM/P4SBRSupermicroSuperServer5010E(SYS5010E0)Supermicro SuperServer5010H(SYS5010H0)SupermicroSuperServer5011E(SYS5011E0)Supermicro SuperServer5011H(SYS5011H0)SupermicroSuperServer5012B6(SYS5012B6)Supermicro SuperServer5012BE(SYS5012BE)TyanComputersTiger200T(S2505)/(S2505TDNGR)Tyan ComputersTiger230/Tiger230T(S2507D)/(S2507T)TyanComputersTrinity450 (S2507S)TyanComputersTrinityI845(S2090)TyanComputersTrinityK7(S2380)Tyan ComputersTrinityKT(S2390)TyanComputersTrinityKTA(S2390B). ProductDescription StorageCapacity UpgradeType
KingstonValueRAMmemory512MBDIMM168PINSDRAM

FormFactor

Technology MemorySpeed DataIntegrityCheck CASLatency Features

Generic SDRAM

512MB DIMM168PIN

133MHz(PC133)

NonECC CL3

Unbuffered 3.3V Gold

SupplyVoltage LeadPlating

ManufacturerWarranty

Limitedlifetimewarranty(Germany,AustriaandFrance10years)

ExtendedSpecs

General
StorageCapacity UpgradeType

512MB Generic

Memory

DRAM SDRAM DIMM168PIN

Technology ModuleHeight(inch) MemorySpeed CASLatency

1.15 133MHz(PC133) CL3

DataIntegrityCheck RAMFeatures
NonECC Unbuffered 64x64 3.3V Gold
ModuleConfiguration SupplyVoltage LeadPlating

Expansion/Connectivity

CompatibleSlots

1xmemoryDIMM168PIN

Service&ampSupport
*Techdataisnotresponsiblefortheerrorsinthedocumentationofproducts